Special Rep to Bldgs No P-96 and P-97 at Dayal Bagh in Bharatpur

Amount

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and as directed.

Demolition of cement concrete (reinforced) in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and as directed.

Dismantling asbestos cement (corrugated or semi corrugated) sheets in roof coverings, complete all as specified and directed..

Pre painted galvalume zinc coating GI based corrugated steel sheet 0.50 mm thick, sheeting of any colour having strength of 550 mpa as in roof covering etc, complete all as specified and directed.

S&F rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections & MS pipe) including distance pieces, cleats etc. conforming to Fe-410W Gde E-250 quality 'A', complete all as specified and directed.

M&L for mild steel work as in wind ties for roof covering including securing bolts etc. including all necessary drilling, bolting or riveting etc and similar work conforming to Fe 290 Gde E-165, complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground levels) complete all as specified and as directed.

M&L for 100 mm thick PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in sub base complete all as specified and as directed.

M&L for chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed & pointed in neat cement slurry in floors with grey cement & pigment over 15 mm thick screed in CM (1:6), complete all as specified and directed.

M&L 75 mm thick cement concrete 1:3:6 type C2 (using 40mm graded crushed stone aggregate) as in plinth protection/path laid in panel surface finished even and fair without using extra cement complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), and rubbish off the same from premises, complete all as specified and as directed.

M&L for 25 mm thick PCC 1:2:4, type B-0 using 12.5 mm graded stone aggregate as in sub floor, laid and finishing the surface of concrete topping even and rough to receive screed for tiling, complete all as specified and as directed.

M&L for coloured non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exc. 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor, laid over 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for coloured non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exc. 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor, laid over 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for glazed ceramic tiles, coloured/printed tiles in vertical surface of size 450x300x7 mm thick, laid over 15 mm thick rendering in cement mortar (1:3) and set and jointed in neat cement slurry & pointed in white cement with pigment to match the colour of tiles, complete all as specified and as directed.

M&L for 20-25 mm thick kota stone slab as in flooring/steps laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over and including 20 mm thick screed bed in CM 1:6, complete all as specified and as directed.

M&L for 20-25 mm thick machine cut kota stone slab on vertical surfaces such as skirting, dados etc. set and jointed in neat cement slurry and pointed in colored cement to match the shade of Kota stone laid over 10 mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces finishing rough to receive stone, complete all as specified and as directed.

M&L for 18 - 20 mm thick black machine cut granite slab (of any type) (table rubbed and polished), as in steps, jambs, pillars, window- cills, cooking platform set in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab laid over and including 15 mm thick cement screed in cement and sand mortar 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for rounding to edges of stone slab one edge, such as in steps, cooking platform and other similar situation including making of hole suitable for gas pipe etc. complete all as specified and as directed.

Dismantling of Stone slabs in roofs, suspended floors, chajjas, landings, etc., any thickness, jointed in any mortar complete all as specified and as directed.

M&L for sand stone slabs of 50 mm thick in cills, sun-shades, chajjas, shelves, cover stones, templates, etc. n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in cement mortar 1:4, complete all as specified and as directed.

Taking up or down steel tubing and connections, 15 mm bore fixed on walls, floors or ceiling etc including cleaning for re-fixing or removal to store complete all as specified and as directed

Taking up or down steel tubing and connections, 20 mm bore fixed on walls, floors or ceiling etc including cleaning for re-fixing or removal to store complete all as specified and as directed

S&F GI tubing medium grade galvanised with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 15 mm complete all as specified and as directed

S&F GI tubing medium grade galvanised with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 20 mm complete all as specified and as directed .

S&F in repair vitreous china squatting pan,Órissa pattern size 580 x 440 mm white, with integral foot rest and CI 'P' trap complete, all as specified and directed.

S&F in repair Vitreous China wash basin, white, flat back, size 550x400mm including brackets & waste coupling, pipe of polythelene of low or high densitycomplete all as specified and directed.

S&F pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with long screwed shank and fly nuts, with or without lettered "Hot" or "Cold" suitable for 15 mm nominal bore iron pipe, screwed for iron pipe and fixed complete all as specified and as directed.

S&F in repair sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or includingfixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm including waste pipe of polythelene of low or high density including making holes in any type of wall for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0 complete all as specified and as directed.

S & F in repair of chromium plated shower rose 125 mm dia with 200 mm long CP arm with swivel joints, any size, including fixing to steel pipe or union complete all as specified & directed.

S&F in repair of Tubular towel rail, 20mm dia, D type, 60 cm long between flanges complete all as specified and directed.

S&F in repair PVC valveless, syphonic action type, flushing cistern, low level, white, 10 lit capacity with inlet, ball valve, float and handle including brackets, flush pipe complete all as specified and directed.

S&F PVC connection 15 mm size with PTMT nuts of length 450 mm including complete all as specified and as directed.

S&F in repair Bib tap, cast copper alloy, fancy type long body with crutch or butterfly handle, screwed down, suitable for 15 mm nominal bore iron pipe screwed for iron or brass ferrule and fixed complete all as specified and as directed.

S&F in repair 20 mm bore stop valves, cast copper alloy, screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repair 15 mm bore stop valves, chromium plated, screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repair 15 mm bore stop valves, cast copper alloy, fancy type chromium plated with long shank and cup (concealed type), screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repair Waste coupling of PTMT (half or full threaded) of 40 mm bore dia of discarge pipe . (Minimum weight 40mm- 60gms complete all as specified and directed.

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed.

S/F in repair PVC (SWR) floor trap 75mm dia plain with stainless steel grating including jointing with solvent cement complete all as specified and directed.

S & F in repair, 500 ltr ISI marked three layer, white colour, rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) with thread type cover and fixed with screw hoisted and fixed in position & including 20 mm brass ball valve complete all as specified and as directed.

Supply only PTMT ball valve of 20 mm bore high pressure of PTMT with epoxy coated aluminium rod & high denisty plastic ball screwed for iron pipe (minimum wt -210 grams) complete all as specified and as directed.

M & L for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe.290.Gde-E-165, complete all as specified and as directed.

S&F of welded steel wire fabric ,weight n. exc 4.00 kg/sq. m fixed to steel members complete all as specified and as directed.

Demolition & breaking up drain pipes AC, (Salt glazed ware, AC or Reinforced concrete) set in CM Internal dia of pipe 100 mm/75 mm complete all as specified and as directed.

S&F PVC (SWR) pipe not less than 6 Kgf/sqcm rating single socketed, in any length with rubber ring joints including clamps of FI 40x3 mm fixed bolt 8 mm drilled to wall, in walls, type 'B' ISI marked of 110 mm bore complete all as specified and as directed.

S&F PVC (SWR) pipe not less than 6 Kgf/sqcm rating single socketed, in any length with rubber ring joints including clamps of FI 40x3 mm fixed bolt 8 mm drilled to wall,in walls, type 'B' ISI marked of 75 mm bore complete all as specified and as directed.

S&F PVC (SWR) bend of 110 mm bore with access door of any radius including taking down of bend, complete all as specified and as directed.

S&F PVC (SWR) bend of 75mm bore with access door of any radius including taking down of bend, complete all as specified and as directed.

S&F PVC (SWR) Vent cowl of 75mm bore including taking down of old one, complete all as specified and as directed.

S&F PVC (SWR) single T of 110 mm bore equal or un equal including taking down of old one, complete all as specified and as directed.

S&F PVC (SWR) single T of 75 mm bore equal or un equal including taking down of old one, complete all as specified and as directed.

Taking down chowkats or frames n. exc 1.5 sq. m each with shutters (without taking off shutters from the frame) complete all as specified and as directed.

Taking down chowkats or frames exc 1.5 sq. m but n exc 4 sq. m each with shutters (without taking off shutters from the frame) complete all as specified and as directed.

Taking down shutter of any description area n exc 1 sq. m each complete all as specified and as directed.

Taking down shutter of any description area exc 1 sq. m and n. exc 2 sq. m each complete all as specified and as directed.

S&F Plain, framed, panelled shutters 40mm thickness (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats, complete all as specified and directed

S&F factory made, 35 mm thick, 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc.( without sash bars ), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, gauge etc., sizes of members of shutters as specified 8.24(a) in SSR Part I complete as as specified and as directed.

S & F for Solid PVC Door Frame of the size 50 x 47mm made out of 5 mm PVC sheet. The door profiles are to be reinforced with 19x19mm M.S Square tube. The profile shall be cut and mitred at two corners and joined by inserting 2nos. of 150mm long brackets of 15x15mm M.S. square tube inside the 19mm x 19mm M.S. square tube and suitably screwed complete all as specified and as directed.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement all as specified & shown on SSR 2020 (Part-II) complete all as specified and as directed.

Providing and fixing factory made UPVC white colour Sliding window, three track made of extruded profiles with wall thickness of 2.3 mm (+/- 0.2 mm). Window profile with hollow section with multi chamber, Frame (88mm x 52mm), sliding sash (42mm x 67mm), Sliding mesh Sash (42mm x 57mm), Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+/- 0.2 mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners. Hardware : Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and required accessories. Note : The Unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. (a) Area not exceeding 2.00 sqm each

S&F MS butt hinges medium weight cold rolled of size 100 mm, complete all as specified and as directed.

S&F SS hinges medium weight of size 100 mm, complete all as specified and as directed.

S&F aluminium anodised,barrel tower bolts of extruded section, 200 mm length of bolt and fixed with screws, complete all as specified and as directed.

S&F aluminium anodised, barrel tower bolts of extruded section, 125 mm length of bolt and fixed with screws, complete all as specified and as directed.

S&F 250 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy and fixed with screws complete as as specified and as directed.

S&F Aluminium handles, cast type, anodised of 125 mm size complete all as specified and as directed.

S & F window guard bars, plain and fixed independently in steel window frames, conforming to Fe 290 Gde E-165, complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or from metal frame or stone or concrete or bricks surrounds glazesd with putty, taking out old pins punching or drilling out, complete all as specified and as directed.

S & F Sheet glass 4.0 mm thick, ordinary quality & glazing with oil putty in squares n.exc 0.5 sqm in each pane including punching or drilling out old glazing pins/spring clips, and providing & fixing new ones complete all as specified and as directed.

S&F for Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples or rivets, complete all as specified and as directed.

S&F in repair for Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples or rivets, complete all as specified and as directed.

Dismantling/demolition of brickwork or stone boulder masonry built in cement mortar including all quoins, arches, pillars etc, complete all as specified and as directed.

M & L for brick work with sub-class 'B' bricks, straight or curved on plan exc 6.0 metre mean radius as wall built in cement & sand mortar 1:6, complete all as specified and as directed.

Taking down cement or cement lime plaster of any description from brick or stone walls including raking out joints, hacking for key, scrubbing down with water etc., complete all as specified and as directed.

M&L for rendering 10 mm thick in cement and sand mortar 1:6 on fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement, complete all as specified and as directed.

M&L for rendering 5 mm thick in cement and sand mortar 1:3 on fair faces of concrete surfaces as in ceiling including finishing the surface even and smooth without using extra cement, complete all as specified and as directed.

M&L for rendering 15 mm thick in cement and sand mortar 1:4 on brick work or cement concrete surfaces including finishing the surface even and smooth, complete all as specified and as directed.

Supply only Integral water proofing compound

M&L for preparation of newly plastered or un plastered surfaces of walls and applying two coats of oil emulsion distemper white or tinted (copolymer based resin glue to be added for longer durability and better finish) over one coat of water based white pigmented alkali resistant priming paint, over 1 mm thick wall care putty on Wall Surface including all necessary arrangement for execution of work ,complete all as specified and as directed.

M&L Preparation of newly plastered surfaces of ceiling & applying three coats of oil emulsion distemper white or tinted complete all as specified and as directed.

M&L for Preparation of old decorative concrete, plastered/ un-plastered surface of wall including cornices, pilasters etc by brooming down, steel wire brushing ,scraping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots removing nails and filling small holes by putty and prepare the surface and applying one coat of Exterior emulsion paint for external wall Surface, complete all as specified and as directed.

M & L Preparation of new decorated plastered surface of wall including cornices, pilasters etc by brooming down and applying two coats of Exterior emulsion over a coat of alkali resistant primer complete all as specified and as directed.

M&L for painting to new or previously untreated steel surfaces of any description over 10 cm in width or girth with two coats of synthetic enamel paint over a coat of zinc chrome primer including preparation of surfaces complete all as specified and as directed.

M&L for painting to new or previously untreated steel surfaces of any description n exc10 cm in width or girth with two coats of synthetic enamel paint over a coat of zinc chrome primer including preparation of surfaces complete all as specified and as directed.

M&L for preparation of new or previously untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for one coats painting with synthetic enamel paint to old wood or wood based surfaces of any description, not otherwise described over 10 CM width or girth including preparation of surface complete all as specified and as directed.

M & L for Preparation of old distempered surface of wall including cornices etc by brooming down, steel wire brushing ,scraping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots removing nails and filling small holes by putty and applying one coat of distemper oil emulsion white or tinted complete all as specified and as directed.

Ditto all as per Srl item No 4 here in above but applying one coat of distemper oil emulsion white or tinted on ceiling complete all as specified and as directed.

M & L Preparation of old decorated plastered or undecorated plastered surface of wall including cornices, pilasters etc by brooming down, steel wire brushing ,scraping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and applying one coat of white wash on wall complete all as specified and as directed.

Cutting or uprooting grass incl removing old mud phuska/ roof treatment of any thickness and description, removing rubbish off the premises, cleaning surface and preparing to receive new treatment complete all as specified and directed.

M&L for 20 mm thick screed bed or bedding layer of cement mortar 1:4, finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparing surfaces for roof treatment by removing all loose gravel, dirt, oil, grease and foreign matter by jet of dry air and clean the surfaces mechanically or by grinding to make it smooth before application, repair all cracks by cutting "V" groove and fill with PMC mortar (Polymer modified cement mortar) prepared by cleaning free from dust and loose particles and apply on dry surface first coat of crack fillar using putty knife or trowel allow to dry for 4 to 6 hr, afterthat apply second coat and dry for 4-6 hrs in ratio as per manufacturers specification, provide 75 mm x 75 mm coping made out of PMC mortar as above on all joints of vertical upstands to ensure that moisture content in the prepared surface does not exceed 5% immediately before application of liquid membrane. Material incorporation & Protection be provided as Terrasheild first apply with water (ratio terrasheild : water will be 4:1) as primer with coverage area 0.1 Kg per Sqm. After 2-3 hour later, second step apply directly first coat of terrasheild 0.30 to 0.40 mm thickness coverage area 0.5 to 0.75 Kg per Sqm with roller.Spread non woven geo textile of 40 / 50 gsm with overlap of 50 mm in both direction when the surface is still tacky. After 4-6 hour later, apply third step apply directly second coat of terrasheild 0.30 to 0.40 mm thickness coverage area 0.5 to 0.75 Kg per Sqm with roller. final thickness of complete treatment should be minimum 1.0 mm. Water tank and Khurra location one additional coat of terrasheild 0.30 to 0.40 mm thickness coverage area 0.5 to 0.75 Kg per Sqm be provided. after complete application full curing minimum 7 days . Above complete application will be done by authorized apllicator from Manufacturer and manufacturer's specification.

Dismantling boarding of any description, fixed in any position with nails, complete all as specified and as directed.

M&L for 18 mm thick PVC boarding shutters of density exc 550 Kg per Cum but nexc 600 Kg per Cum one side decorative lamination & other sidebalancing lamination sheet fixed with brackets, screws etc, Panels shall be fabricated using adhesive and screws wherever required all the edges shall be coverd with 18 mm x 1 mm thick edge bending tape or 90 degree edge bend finish as per manufactrure specification or approved pattern complete all as specified and as directed.

M&L for 18 mm thick PVC boarding shelves of density exc 550 Kg per Cum but nexc 600 Kg per Cum one side decorative lamination & other sidebalancing lamination sheet fixed with brackets, screws etc, Panels shall be fabricated using adhesive and screws wherever required, Supported for three sides with 18 mm x 18 mm PVC Ply fixed with Screw all the edges shall be coverd with 18 mm x 1 mm thick edge bending tape or 90 degree edge bend finish as per manufactrure specification or approved pattern complete all as specified and as directed.

S&F for stainless steel 125 mm handle not less than 12 mm dia suitable for cupboard shutters with self tapping stanless steel screw complete all as specified and as directed.

S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised with width of flaps (When open) 40 mm complete all as specified and as directed.

S&F Magnet catch for shutters as per approved sample complete all as specified and directed.

Taking down carefully & refixing of exhaust fan (Metal/PVC) in serviciable condition with connecting wire PVC insulated twisted flexible 0.5 sqmm coppper conductor complete all as specified and directed.

Taking down carefully & refixing of tube light fitting/wall light/mirror light/holder with conncting wire PVC insulated twisted flexible copper conductor complete all as specified and directed

Taking down carefully & refixing of electric meter & DBs with connecting wire PVC insulated twisted flexible copper conductor complete all as specified and directed.

Supply and fixing of 18/20 watt LED tubelight fitting retro fit type 4 x feet alonwith replaceble rod complete with all accessories and including connecing up with three core twisted flexible copper conductor cable with suitable size of 230V, 50 Hz complete all as specified and directed.

S& F ceiling fan (white of 1200 mm sweep, 5 star rating copper wound with super energy efficient BLDC motor including remot, connecting wire PVC insulated twisted flexible 0.5 sqmm copper conductor canopy set down rod, shackle kit, including taking down old u/s ceiling fan deposited to AGE E/M store yard all standard accessories complete all as specified and directed

GOVIND CONSTRUCTION (BID ID -3094976)

Tulsi Enterprises (BID ID -3088980)

krishna Associate (BID ID -3088258)

M/S MAMTA CONSTRUCTIONS (BID ID -3088490)

Captainkomalchaharconstructions (BID ID -3085024)