GE (N) P/TOKEN- 65 OF 2021-2022PROVISION OF CERTAIN MW AND SPECIAL REPAIR WORKS IN THE AREA OF AGE B/R (CENTRAL) UNDER GE (NORTH) PUNE

Amount

Material and labour for roof tiles Mangalore pattern interlocking at side joints, laid dry including dismantling single layer Mangalore pattern or similar tiles in roofing and rubbish off the premises complete all as specified and as directed.

Ditto all as per serial item No.2.00 here-in-before but except tiles.

Dismantling of 2nd class hardwood clean sawn tile battens, cross sectional area exc 5 and n.exc 15 Sqcm spaced at 30 cm centres to centres fixed with nails complete, scantling and rubbish off the premises all as specified and as directed. (NOTE:Measurements shall be taken overall including both battens and spaces.

Dismantling of 2nd class hard wood, clean sawn, in scantling timber work size area exc 40sqcm and over rubbish off the premises all as specified and as directed.

M&L Fibre board Eves/Weather Boarding 18 to 20mm thick or Feather Edged 15mm to 20mm thick and fixed with 30mm Lap, complete approved arch pattern any size and shape all as specified and as directed.Make: Shera wall/Everest

Dismantling plain or corrugated steel sheeting , any gauge or any thickness, as in roof coverings complete all as directed.

Supply and fix for 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc with grade of zinc coating 120gms/ Sqm complete all as specified and as directed.

Ditto all as per serial item No.7.00 here-in-before but except sheeting.

Supply and fix in repairs 0.56mm thick plain, Aluminium sheeting, alloy 31000H4 in ridges, hips, valley gutter, crumple joint, drip and straight flashing (length and girth as fixed) complete all as specified and as directed.

M&L for PCC (1:5:10) type E2 (using 40mm graded stone aggregates) as in sub base including demolition of existing PCC and removing rubbish off the premises complete all as specified and directed.

M/L for 15mm thick cement plaster in CM 1:6 on brick or concrete surfaces finished even and smooth as specified and directed.

Taking down cement plaster on brick/ stone walling including raking out joints, hacking for key, scrubbing down with water etc complete all as directed.

M&L Brick work with fly ash bricks, conforming to IS- 12894:2002, Non modular, class designation 75, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 etc including demolition of brickwork built in cement mortar and rubbish off the premises complete all as specified and directed.

Material and labour for rendering 15mm thick in cement mortar (1:4) on fair faces of brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L Solid PVC Wall Lining consisting of 5mm thick wood grain etc complete all as specified and directed. printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as specified and directed.

M&L 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing and as specified and directed.

M&L 5mm thick plain colour PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining, Insulated PVC Wall Lining, and Solid PVC Partitions inclusive of Solvent Cement and fixing at site all as specified and directed.

Dismantling of wooden boarding any description and in any position complete all as directed.

Material and labour for false ceiling with 10mm thick 600mm x 900mm plaster of paris sheets fixed with machine screws on GI channel 18 gauge thick, grid work main joists placed at 750mm centres, secondary joists placed at 450mm centres, GI angle suspenders from roof and treating the plaster of paris sheets with thin layer of POP with Gypsum binder, sanding the surfaces till smooth surface is obtained including preparation of surfaces and applying two coats of oil bound distemper over a coat of primer including dismantling of existing ceiling of any description and any thickness including grid etc complete all as specified and as directed.NOTE: pop ceiling to be made in two /three tier design)

M&L for PCC (1:2:4) type B1 (using 20mm graded stone aggregates) as in roof kerbs or mud stops rounded or chamfered on edges as in Coping including necessary formwork complete all as specified and directed.

Material and labour for 12mm thick mineral fibre false ceiling board on and including GI powder coated grid work of size 600 mm x 600 mm with using 32.0 mm x 20 mm x 1.5 mm thick main tee, 23.5 mm x 23.5 mm x 1.28 mm cross tee and 25 mm x 25 mm x 1.5 mm angle fixed to wall for false ceiling including necessary supporting hanger with 3.0 mm dia GI wire and 'J' bolts washer nuts for securing frame work to ceiling, suspended @ 120 cm C/C both ways, size of grid shall be 605 mm x 605 mm complete all as specified and as directed. Make :- Armstrong, Diaken, New Age.

Material and labour for false ceiling with made up of size 1800mm x 1200mm x 12.5mm thick, tapered edge gypsum board (Gypboard) Plain (conforming to IS 2095-Part 1:2011, Certified board) is then screw fixed to ceiling section with 25mm drywall screws {Material-Carbon steel EN-ISO 7049/50, Finish-Case hardened Grey Phosphating} at 230mm centres on ceiling section & 150mm at periphery of ceiling. Finally square and tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with Gyproc Pro-Fill Jointing compound (Conforms to ASTM C475), Gyproc Joint Paper tape fixed on metal grid of hot dipped galvanized steel sections and suspended as per manufacturer's specifications and instructions including dismantling of ceiling board of any description and any thickness including cover fillets/ grid etc.complete all as specified and as directed. Make: Gyproc-Saint Gobain or equivalent of Armstrong, Diaken, New Age (ACE) as approved by GE.

Material and labour for plaster of paris decorative cornices/ moulding to the pattern as approved, cross sectional area exceeding 13 Sq.cm and not exceeding 25 Sq.cm and fixed in decorative pattern including preparation of surfaces and applying two coats of oil bound distemper over a coat of primer matching with the colour of ceiling including dismantling existing complete all as specified and as directed.

Material and labour for 12mm thick plywood, grade BWR, type BB, number of ply 7 Nos, fixed with fevicol and nails for working table/ storage almirah wall panelling to the size and pattern complete all as shown on drawing and as directed.

Material and labour for 2nd class hard wood sal plain fillets, square, rectangular or triangular in section, bull-nosed, splayed, chamfered or rounded on one edge or face, wrought, secured with fevicol and nails or brads, sectional area exc 13 and not exc. 25Sq.cm complete all as specified and as directed.

Material and labour for 4mm thick one side decorative group match veneer complete all as specified and as directed.

Material and labour for applying one or two or more coats of melamine polish over veener surface with spray guns, compressor etc complete till fine glossy surface is obtained complete all as specified and as directed.

Taking down wall panelling including veneer, plywood & Batten complete all as specified and as directed.

Taking down old Aluminum partition along with glass and board carefully all as directed.

Refixing old Aluminium partition along with glass and board all as directed

Supply and fix for aluminium powder coated partition using ‘Jindal’ aluminium SP/ DP section or equivalent make as specified with 5mm thick tinted glass, PVC rubber beading,12mm thick prelaminated particle board fixed with glazing clips etc complete all as specified and as directed. Sections : SP (Single partition) - 20033, DP (Double partition) - 20034,Glazing clips - 4407

Supply and fix for aluminium anodised powder coated three track sliding window with two glazed shutters, one shutter with and including 4mm thick ordinary quality float glass and one shutter with and including stainless steel wire mesh 0.36 mm dia wire and 1.40mm aperture including good quality of bearing, handle, locks, PVC rubber lining of transparent colour etc. complete all as specified and as directed. Catalouge numbers of Jindal company or equivalent make sections : Three track bottom – 20957, Three track top/vertical – 20958,Handle – 20606, Interlocking – 20605, Top and bottom – 20604.

Taking down chowkats or frames with shutters (without taking off shutters from frame) area exc.1.5 sqm and not exc.4 sqm each complete all as directed

Supply and fix for powder coated aluminium single/double leaf, two panels, openable door , 5mm thick plain glass panes fixed with garware sun control film, fixed with rubber beading and glazing clips, alongwith supplying and fixing aluminium body hydraulically regulated door closer, designation No 2 universal type, suitable for sheet width 701 to 850mm of weight between 36 to 80 kg , mortice door lock, handle, tower bolt 200mm (02 Nos.), aluminium sliding bolt using aluminium sections all as specified and directed. Note :- Catlouge numbers of Jindal or equivalent company. (i) Top-19528 (ii) Middle-19575 (iii) Bottom-19530 (iv) Vertical-19526 (v) Glazed clips section No. 19381 and 19352 (vi) 1'' interlock (20939) (vii)1'' handle(20602) .

Supply and fix for 30mm thick flush shutters solid core construction, with block board core and plywood face panels, commercial type on both sides including second class hard wood plain cover fillets 35X6mm all around the shutters complete all as specified and as directed

Material and labour for 0.90mm thick decorative laminate type 1 of surface finish, colour, pattern and size as approved, fixed with approved adhesive as per manufacturer’s instructions on horizontal and vertical surfaces etc. complete all as specified and as directed.

Taking down shutters of any description, area exc.2sqm each complete all as specified and as directed.

Factory made 100 % solid wood plastic composite(WPC) door frame, single rivet 90 mm x 45 mm made from wood plastic composite (Single extruded process) material with density 780 Kg/ Cum complete all as specified and directed.NOTE: During Fixing of chowkhat, surface Shall be make good in plumb with existing finishes like cement plaster, similar wall tile,floor tile etc and as per site requirement.

Supply and fix for 28 to 30 mm thick WPC board in door shutter complete all as specified and directed

Supply and fix for 75mm size butt hinges, extruded brass with mild steel hinge pin, bright polished and fixed type D-11 complete all as specified and as directed.

Supply and fix for aluminium powder coated louvered ventilator with provision of exhaust fan using ‘Jindal” aluminium section or equivalent make as specified including glass 3mm thick ordinary quality, frosted and stainless steel wire mesh 0.36mm dia wire and 1.40mm aperture etc complete all as specified and directed.

Preparation of old surface of wall/ceiling by filling cracks by crack fill paste of Berger or equivalent make , removing loose paints etc , removing nails etc and make good surface by applying white birla/JK wall putty wherever required, smoothen surface by sand paper and applying one coat of weather proof exterior emulsion paint ('APEX' brand of Asian or equivalent brand of Berger/Shalimar) complete all as specified and as directed.

M&L for applying two coats of weather proof exterior emulsion paint ('APEX' brand of Asian or equivalent brand of Berger/Shalimar) roof/ wall /floor etc, over a coat of primer complete all as specified and as directed.

M&L for preparation of old painted steel surfaces of any description over 10cm girth or width and applying one coat of synthetic enamel paint complete all as specified and as directed.

Material and labour for preparation of old treated plastered or unplastered surfaces of wall by removing all loose paints etc removing nails ,applying birla putty whereever required, smoothen the surface with sand paper and finally applying one coat of acrylic distemper complete all as specified and as directed.

Material and labour for appyling two coats of acrylic distemper of approved tint on ceiling surfaces complete all as specifie and as directed.

Material and labour for preparation of New plastered or unplastered surfaces of ceiling , applying birla putty whereever required, smoothen the surface with sand paper and finally applying two coat of acrylic distemper complete all as specified and as directed.

Material and labour for preparation of New plastered or unplastered surfaces of walls , applying birla putty whereever required, smoothen the surface with sand paper and finally applying one coat of acrylic distemper complete all as specified and as directed.

M&L for complete removal of existing treatment on walls using steel wire brush, sanding machine, rubbing ivory papers etc and washing , rubbing down and stopping of distempered and painted surfaces, preparing surfaces plastered or unplastered surfaces ready to receive new finish complete all as specified and directed.

M&L for applying wall care putty 1 to 1.5 mm thick on walls surfaces.

M&L for applying one coat of alkali resistant priming paint on wall.

M&L for two coats of acrylic distemper of approved tint on wall surfaces

M&L for mild steel framed work such as grill, grating etc. with ends of bars shouldered or rebated or forged into spike framed guard bars barred iron doors, ladders, framed baluster, walk way, railing; frame work, including pintle hinges, stops, hand-made sliding bolts etc,sliding channels for sliding of gate and similar work conforming to Fe 290 Gde-E-165 complete all as specified & as directed.

M&L for preparation of New steel surfaces of any description over 10cm girth or width and applying one coat of synthetic enamel paint over a coat of Red Oxide Primer all as specified and directed

M&L for double charged vitrified ceremic tiles 10 mm thick (square/rectangular) polished, area of each tile exc. 0.42 sqm not exceeding 1 sqm, in flooring etc , laid over and including screed bed of 15 mm thick cement mortar (1:4) and jointed in neat cement slurry and pointed in white or coloured cement to match dark shade complete all as specified and directed.

M&L for double charged vitrified ceremic tiles 10 mm thick wooden texture size- 200 X 1200 mm, plank type laid over and including screed bed of 15 mm thick cement mortar (1:4) and jointed in neat cement slurry and pointed in white or coloured cement to match dark shade complete all as specified and directed.

Material and labour for coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular), area of each tile exceeding 0.06sq.m but not exceeding 0.11sq.m as in floor etc., colour and pattern as approved by GE, set and jointed in neat cement slurry using grey cement and pointed in white or coloured cement to match the colour of tiles, laid over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and as directed.

M&L for coloured glazed ceramic tiles of size 600mm x 300mm x 7 to 8mm thick highlighter tiles of colour and pattern as approved by GE, as in vertical surface, set and jointed in neat cement slurry using grey cement and pointed in coloured cement to match the colour of tiles over and including 10mm thick screed bed in cement mortar 1:3 including dismantling existing tiling, cement mortar bedding (but not backing), removing rubbish off the premisescomplete all as specified & directed.

M&L for coloured glazed ceramic tiles of size 600mm x 300mm x 7 to 8mm thick of colour and pattern as approved by GE, as in vertical surface, set and jointed in neat cement slurry using grey cement and pointed in coloured cement to match the colour of tiles over and including 10mm thick screed bed in cement mortar 1:3 including dismantling existing tiling, cement mortar bedding (but not backing), removing rubbish off the premisescomplete all as specified & directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as directed.

Material and labour for double charge coloured vitrified tiles 10mm thick (square/rectangular) polished, area of each tile exc. 0.18 Sqm but not exc. 0.36 Sqm as in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles, laid over and including 20mm thick screed bed in cement mortar (1:6) complete all as specified and as directed.

M&L 25 mm thick plain cement concrete (1:2:4), type B-O (using 12.5mm graded stone aggregate) as in sub base to receive tile/claddings tops including demolition of existing cement concrete complete all as specified and directed.

Material and labour for machine cut cudappah stone slab 20-25 mm thick as in lintels, shelves, vertical surface, fixed with neat cement slurry or arldite, including rubbing and polishing complete all as specified and as directed

Supply and fix for 300mm long aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, ISI marked, complete all as specified and as directed.

Supply and fix for 300mm long brass sliding door bolts with sand or die cast brass hasp, staple (bolt type) and fixing bolt with roller or drawn brass bolts, ISI marked, complete all as specified and as directed.

Supply and fix for 200mm long aluminium anodised, barrel tower bolts of extruded section, complete all as specified and as directed.

Supply and fix for 150 mm long aluminium anodised, barrel tower bolts of extruded section, complete all as specified and as directed.

Supply and fix for butt hinges, 100mm size, mild steel cold rolled, medium weight complete all as specified and as directed.

Supply and fix for floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, overall length of cover plate 150mm all as specified and as directed.

Supply and fix for 100mm size brass handles, extruded, fabricated type, polished complete all as specified and as directed.

Supply and fix for 150mm size extruded aluminium alloy handles fabricated type anodised complete all as specified and as directed.

Supply and fix in repairs for vitreous china coloured wash down water closet (pedestal pattern) cascade type ‘P’ trap, in built seat cover and flushing cistern, low level, valveless, symphonic action type complete with inlet ball valve, float and handle complete all as specified and as directed. Make :- Hindware , catalogue No. 20028 Constellation, 21038 cistern, pastel (complete set) or equivalent from Cera/ Parryware. Note :- If Cat No. is revised, equivalent cat No. from latest catlauge shall be considered.

Supply and fix in repair for vitreous china European type wash down water closet pan, (Pedestal pattern), white including plastic water closet white closed pattern with flat bottom and cover with mild steel chromium plated hinging device and fixing bolts, necessary inlet and outlet, anti-syphonage pipe connections including making good complete all as specified and as directed.

S&F in repairs Chromium plated single lever extended basin mixer (height 150 mm) without popup waste system with 450mm long braided hoses as per Cat No FUS- 29005NB of make Jaquar 'FUSION' series or equivalent of makes asper Appx 'A' as approved by GE complete all as specified and as directed.

Taking up or down 15 mm bore steel tubing with all fittings and connections including cleaning for refixing or removal to store complete all as directed.

Taking up or down 20 mm bore steel tubing with all fittings and connections including cleaning for refixing or removal to store complete all as directed.

Supply and fix for 15 mm bore GI tubing 'medium grade' galvanised, with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and as directed.

Supply and fix for 20 mm bore GI tubing 'medium grade' galvanised, with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and as directed.

Refixing 20mm dia old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) complete all as directed.

Refixing 15mm dia old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) complete all as directed.

Material and labour for PP-R gate valves (brass insert) of 20mm bore complete including taking down old unserviceable valve all as specified and as directed.

Material and labour for cutting chases in brick wall, not exc. 10cm girth, pinning in for concealed water tubing and making good to facings where required and pointing to cenment mortar (1:3) complete all as specified and as directed.

Supply and fix for factory made solid Panel PVC door shutter, 30mm thick (style) consisiting of frame made out of MS tubes for top and bottom rails. M.S. frame shall covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheets for top rail, lock rail, bottom rail; panelling of wood grain printed PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (90°) and joined together with solvent cement, suppling and fixing in the frame at site as per specification and drawing including fittings complete all as specified and as directed. Make: Rajshri/ Sintex/Duraplast/Accucell

S&F in repairs, chromium plated bib cock with wall flange quarter turn complete all as specified and as directed. Cat No. FUS-29037 of make Jaquar ‘Fusion ' series or of equivalent make as per Appx 'A' as approved by GE.

S&F in reapir 15mm dia Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed.

S&F in repairs brass chromium plated quarter turn two way bib cock with wall flange 15mm dia Cat No. FUS-29041 of make Jaquar ‘FUSION series or equivalent as per Appx 'A' as approved by GE complete all as specified and as directed.

Supply and fix in repairs, chromium plated pillar cock 15mm dia quarter turn as per Cat No.FUS-29001 of make Jaquar ‘FUSION ' series or equivalent of make as per Appx 'A' as approved by GE complete all as specified and as directed.

S&F in repairs chromium plated single towel rail 600mm long including built in side brackets ,Cat No. AKP-35711 of make Jaquar ‘KUBIX PRIME' Series or other equivalent series of Jaquar or equivalent of makes as per Appx 'A' as approved by GE complete all as specified and as directed.

S&F in repairs chromium plated toilet paper holder ,Cat No. AKP-35751 of make Jaquar ‘‘KUBIX PRIME" Series or other equivalent series of Jaquar or equivalent of makes as per Appx 'A' as approved by GE complete all as specified and as directed.

S&F in repairs chromium plated soap dish ,Cat No. AKP-35731P of make Jaquar ‘KUBIX PRIME'S Series or other equivalent series of Jaquar or equivalent of makes as per Appx 'A' as approved by GE complete all as specified and as directed.

S&F in repairs chromium plated towel rack, 600mm long with lower hangers, Cat No. ACN-1181FHN of make Jaquar ‘CONTINENTAL'S Series or other equivalent series of Jaquar or equivalent of makes as per Appx 'A' as approved by GE complete all as specified and as directed.

Supply and fix for vitreous chinaware wash hand basin, table top type with fixing accessories set, CP brass waste coupling, chain and plug and porcelain stopper, waste fittings, union and waste pipe 32 mm dia of required length, 15mm dia PVC connection 450mm long including PTMT nuts and all necessary inlet outlet connections (excluding tap) complete all as specified and as directed. Make: Hindware CAT Part No. 91064, or equivalent of makes as per Appx 'A' as approved by GE

Material and labour for 18 to 20mm thick granite (of any type) work ( table rubbed and polished) in steps , jambs. pillars, window cills, cooking platforms and any other platform like in cement mortar (1:4) over and including 10mm thick backing coat in cement mortar (1:3), pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including cutting, edge moulding, full curving the edges complete all as specified and as directed.

Labour only for full round moulding to 18 to 20mm thick granite slab all as directed by Engineer-in-Charge.

Supply and fix in repairs 10 litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, 32mm dia PVC flush pipe and connections to pipes, making good the disturbed surfaces complete all as specified and as directed.

S&F stainless steel health faucet witrh 1 Mtr tube and hook complete all as specified and directed ny Engr-in-charge. Confirming to Cat part No ALD573 of jaguar completed all as specified

Supply and fix in repairs for vitreous china EWC of white colour with plastic water closet seat closed pattern with flat bottom (with MS or CP hinging device) and fixing bolts, including connection to drain or out going pipe and to PVC flusing pipe, antisyphonage pipe and all necessary fittings etc complete all as specified and as directed.

Supply and fix in repair for hand shower (health faucet), with 1 metre long easy flex tube in chrome finish & wall hook, Cat No. F160068 of make Hindware or equivalent as per Appx 'A' as approved by GE complete all as specified and as directed.

S&F in repairs vitreous chinaware wash hand basin, size 550x400 mm chromium plated,including CP waste coupling, chain and plug, waste fittings, union and waste pipe 32 mm dia of required length and all necessary inlet & outlet connections complete fixed in repairs. Cat No. - 10091 Starwhite complete set Make - Hindware or equivalent.

S&F in repairs vitreous china Urinal, Flat back Eureka Size- 37x39x60cm Cat No- 60020 starwhite half stall type,white with waste pipe and CP brass spreader complete including providing and fixing plugs, bedding urinal against wall in CM (1:2), securing urinal to plug with and including 60mm long brass screws, pointing around urinal back in cement; flush pipe, grating and union for discharge pipe including brass CP urinal spreader for fixing with 15mm dia pipe complete all as specified and directed.

Supply and fix in repairs for 5mm thick float glass looking mirror fixing with Brass CP Bracket all as specified complete all as specified and as directed.

Supply and fix for 15mm dia PVC connection 450mm long including PTMT check nuts etc complete all as specified and as directed

Supply and fix in repair for 15 mm bore bib taps chromium plated, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule all as per Cat No.PIS-06 (Neptune Series) of make Prayag or equivalent complete all as specified and as directed.

Supply and fix in repairs 15 mm bore pillar tap high pressure screwed for iron pipe all as per Cat No.F330002CP of Make Hindware or equivalent complete all as specified and as drected. (Minimum weight 110 gms).

Supply and fix in repairs for 15mm dia angle cock CP of any colour high pressure screwed for iron pipe all as per Cat No. F 740039 of make Hindware or equivalent complete all as specified and as directed.

Supply and fix in repairs for grating round doom 100mm dia of PTMT (minimum weight 25gms) all as per Cat No.111of make Prayag or equivalent complete all as specified and as drected.

M&L PVC (SWR) branch piece single Y equal or unequal of 75mm dia with access door

M&L for 150 mm bore pipe for Concrete bed to drain pipes including packing under, and hunching against the sides of pipes after they are laid and tested; in cement concrete, type D-2 , 1:4:8 (using 40mm graded stone aggregate) complete all as specified and directed.

M/L 150mm dia reinforced cement concrete pipe Class NP2 laid and jointed complete with collars and laid in trenches complete all specified.

S&F for 50 mm thick , 900x650 mm , heavy duty factory made precast RCC cover slab with frame, RCC in 1:2:4 type B1 using 20 mm graded stone aggregate including reinforcement with mild steel TMT bars 6mm dia @ 150 mm c/c both wasys and set in cement mortar 1:4, finished the surface even and fair complete all as specified and as directed.

M&L for cutting into existing manhole for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel in CM 1:2:4 Type B1 smooth finished reforming benching as required. Internal dia of pipe 150mm.

S&F Stack Clamps made out of (50mmx5mm) flat iron and 12mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for pipe 100mm bore.complete all as specified and directed.

M/L PCC 1:3:6 type C-2, 75mm thick using 40mm graded stone aggregate as in plinth protection and similar works including finishing surfaces even and smooth without using extra cement etc.complete all as specified and directed.

S&F in repair for cast iron Nahani trap, with grating of diameter of outlet 75mm including jointing to waste pipe fixed in PCC (1:2:4) type B-1 (using 20mm graded broken stone aggregates) complete all as specified and as directed.

S & F of mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS1161-1998 grade ST.-240,as in main cross beams and running rails fixed independently with angle iron cleats or connecting pieces complete all as specified and directed.

S&F in repairs chrome plated towel ring square with round flange, Cat No. CAN-1121N of make Jaquar ‘CONTINENTAL'S COLLECTION' Series or equivalent as approved by GE all as specified and as directed.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid on wall fixed complete all as specified and directed

S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid on wall complete all as specified and directed

S&F PVC (SWR) bends, 75 mm bore, any radius with access door complete all as specified and directed.

S&F PVC (SWR) bends, 110 mm bore, any radius with access door complete all as specified and directed.

S&F PVC (SWR) Junction, single, (single T) equal or unequal, 110 mm bore,with access door complete all as specified and directed.

M&L for PVC (SWR) vent cowl, 110 mm bore complete all as specified and directed.

S/F in repair 75 mm bore PVC (SWR) floor trap plain with grating incl jointing with solvent cement complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and average 15 cm and getting out etc as specified and directed by Engr-in Charge.

M&L Hardcore of broken stone of guage nexc. 63 mm deposited spread and levelled in layers nexc. 15 cm thk watered and rammed to true surface.

M&L for PCC type D2 (1:4:8, using 40mm graded stone aggregate) as in sub base.

M/L cement Ready mix concrete type B-2 1:2:4 ( 20 mm graded agg) nominal mix laid over sub base finished even smooth without using extra cement (Concrete to be laid in alternate panel not exc 10 sqm in each panel)

M&L for PCC type B1 (1:2:4, using 20mm graded stone aggregate) as in coping.

M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggregate ) as in foundation concrete in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases)

M&L for Precast cement concrete solid block masonry exc 10cm in width and set in CM(1:6) Mix 1:3:6 , Type C-1 all as specified.

M&L for rendering 15mm thick in cement mortar (1:4) on fair faces of brickwork or concrete surfaces finished even and smooth.

M&L for preparation of newly plastered surfaces and applying three coats of white wash on walls Complete all as specified and as directed.

S & F of mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS1161-1998 grade St.-240,as in main Columns/ Posts cross beams and running rails fixed independently with angle iron cleats or connecting pieces complete all as specified and directed.

M&L Mild steel work of angle, channel plates etc as in framed roof truss , purlins brackets etc including bending and welding angles,bolts as necessary, gusset plates, riveting, etc , conforming to Fe 290 Gde-E-165 complete all as specified and as directed.

Supply and fix for 0.50mm thick pre-painted galvalume aluminium zinc coating (AZ-150) GI based corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screws with side lap complete including dismantling unserviceable asbestos cement (Corrugated, Semi corrugated etc.) sheets all as specified and as directed.

Taking down carefully exising unserviceable aluminium point wiring (light, fan, socket or power), complete (fitting such as switches,ceiling rose, pendent, regulators etc) removing material to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately and making dood disturbed surfaces of wall, floor etc. complete all as specified and as directed.

Taking down of old unserviceable sub main wiring of any type complete all as specified and as directed.

Taking down the existing unserviceable main switch / cut out / DBs of any type / capacity / description as existing at site including necessary making good the disturbed surfaces to match with the existing finishes all as specified.

M & L for Point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sq. mm (nominal area), two single core, PVC insulated and unsheathed FRLS cable 1100 volts grade ISI-694 marked drawn through in and including heavy duty, PVC concealed conduit of white/ ivory colour including all accessories after chasing in wall/ceiling etc, heavy duty ISI marked, with GI sunken boxes 1.2 mm thick, 60 mm deep with earth dolly duly, covered with modular white cover plate with frame suitable for modular switches, including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly all as specified and directed for One light point controlled by one, one way switch 5 Amps

Ditto all as per serial item No 140.00 here-in-before but for One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator

Ditto all as per serial item No 140.00 here-in-before but for One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad.

Ditto all as per serial item No 140.00 here-in-before but for One bell point controlled by one, bell switch 5 Amps

Ditto all as per serial item No 140.00 here-in-before but for One 3 pin 5 Amps switch socket outlet point controlled by one switch on the same board.

Ditto all as per serial item No 140.00 here-in-before but with stranded copper conductor 2.5 Sqmm (nominal area), single core, PVC insulated and unsheathed multistranded FRLS cable 1100 Volt grade ISI-694 marked for 3 pin, 15 Amp socket outlet on independent board including PVC insulated multistranded copper conductor 2.5 Sqmm (nominal area) single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly.

Ditto all as per serial item No 140.00 here-in-before butusing 4.0 sq mm single core copper conductor FRLS cable of multistranded PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 4.0 sq mm PVC insulated copper conductor FRLS cable as earth continuity conductor along with wiring and connecting to the common eath dolly.

S & F for modular step type fan regulator 120 watt single module suitable for operation on 230 volt 50 HZ AC supply including removal of old unserviceable one complete all as specified and as directed

S & F for celling rose 2/3 terminals, PVC/ polycarbonate, isolated body ISI marked complete all as specified.

S & F for Modular switch one way 6 A, 1 module complete all as specified.

S & F for Modular switch one way 16 A, 1 module, with neon indicator complete all as specified.

S & F for Modular socket, 6A - 2/3 pin combined 2 module complete all as specified.

S & F for Modular socket, 6A/16A - 2/3 pin combined 2 module complete all as specified.

S & F for modular Bell push modular 6 Amps single module complete all as specified.

Suply and fix for Bell Electric Ding dong type suitable for operation on 230 volt 50 HZ A C supply complete all as specified and as directed

S & F for recess mounted 2' x 2' square LED panel 36 watts, 600 x 600mm size, sleek design aluminium housing, polycarbibate diffuser white powder coated finish operating voltage 140 volts - 270 volts, AC, 50 Hz complete all as specified and as directed.

S & F for LED down light recess mounted luminare, square type 15 watts with efficiency of 100 lumens per watt, sleek design aluminium housing polycarbonate diffuser white finish operating voltage 150 V-270 V AC, 50 Hz all as specified and as directed.

S & F for LED hanging light for table adjustable type, square type 15 watts with efficiency of 100 lumens per watt, sleek design glass housing finish operating voltage 150 V-270 V AC, 50 Hz all as specified and as directed.

S & F for wall mounted LED 20 watts with out put of 2000 lumens,box type (decorative) light fitting,230 volts with extruded aluminium heat sink provided for efficient heat disspation and integrated electronic driver connector block etc complete with all accessories internally pre wired and necessary mounting arrangments provision of new 3 core muiltistrand copper conductor of size 23/0.193 from ceiling rose to fitting including LED tube 4'x20 watts complete all as specified and as directed.

S & F for LED 10 watts batten aluminium extruded with decorative end caps complete all as specified and as directed.

S & F for plastic body Exhaust fan, AC Single phase ,240 V of size 250 mm sweep with louvers (as per Cat Part No - Maxma DX 8" of make Bajaj or equivalent in Crompton/Havells) including necessary connection and replacement of flexible copper cable from ceiling rose and taking down old unserviceable fan complete all as specified and as directed.

S & F for MCB DB VTPN 4 way with provision for FP MCB/Isolator/RCCB etc as incommer and SP/TP MCBs as out going double door IP 43 complete prewired including Bus Bar including MCCB 63/100 Amps 4 pole for incoming etc suitable for operation on 415 volt 50 Hz AC supply including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed .

S & F for sheet metal enclosure MCB DB TPN 4 way with 200 Amps rated bus bar 415 volts including MCB TPN 63 Amps suitable for fixing double door with magnetic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed. Make -Legrand/L&T/ ABB

S & F for MCB DB, SPN, sheet metal enclosure, 8 way with 200 amps rated bus bar double door, fixed on wall good to disturbed surfaces, and connecting with existing cable complete all as specified and directed.

S & F for MCB tripple pole and neutral rated capacity 63 Amps, 415 volts breaking capacity 10 KA complete all as specified and as directed.

S & F for MCB tripple pole and neutral rated capacity 32 Amps, 415 volts breaking capacity 10 KA complete all as specified and as directed.

S & F for MCB Single pole and neutral rated capacity 40 amps, 240 volts breaking capacity 10 KA complete all as specified and as directed.

S & F for MCB Single pole rated capacity 5 to 32 amps, 240 V breaking capacity 10 KA complete all as specified and as directed.

Taking down carefully ceiling fan of any sweep, keeping with safe custody and refixing the same with replacement of unsv 3 core PVC insulated PVC sheated 3 core multistranded copper conductor cable of size 23/ 0.193 from ceiling rose to fan terminal over hauling the fan, replacement of fan condensor 2.5 Mfd and painted with synthatic enamel white colour paint by spray machine including filling of cavities with filler material complete all as specified and as directed.

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLS cable with stranded copper conductor of size 6.0 Sqmm nominal area and drawing into PVC non metallic rigid PVC casing caping including one run of PVC insulated 6 Sqmm (nominal area) stranded copper conductor FRLS cable as earth wire complete all as specified and as directed. Note:- Two runs of 6.0 sqmm cable,one run of 6 sqmm cable and one run of PVC heavy duty concealed conduit will be measured as one unit

M & L for Sub main wiring with approved colour coding as per IS with four single core PVC insulated FRLS cable with multistranded copper conductor of size 10 Sq. mm nominal area and drawing into PVC non metallic rigid heavy duty PVC conduit and its accessaries ISI marked heavt duty of suitable size including with two runs of PVC insulated 10 Sqmm (nominal area) multistranded copper conductor FRLS cable as earth wire and connected from DB to DB/ main boardcomplete all as specified and as directed. Note:- four runs of 10 sqmm cable, two runs of 10 sqmm cable and one run of PVC heavy duty conduit will be measured as one unit.

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLS cable with multistranded copper conductor of size 4.0 Sq mm nominal area and drawn through PVC non metallic rigid PVC casing caping and its accessories including one run of PVC insulated 4 Sq mm (nominal area) multistranded copper conductor FRLS cable as earth wire and connected from DB to DB/ main board complete all as specified and as directed. Note:- Two runs of 4 sqmm cable,one run of 4 sqmm cable and one run of PVC casing caping and accessories will be measured as one unit

Supply and fix single pole and neutral enclosure with a two pin and earth plug and socket complete with 20 Amps MCB single pole.

Supply and fix Rigid non-metallic PVC conduit of size 25mm exclusive of boxes (junction/terminal) but inclusive of all tees, bends,elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, locknuts, saddles, pipe hooks etc.

Supply and fix Rigid non-metallic PVC conduit of size 40mm exclusive of boxes (junction/terminal) but inclusive of all tees, bends,elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, locknuts, saddles, pipe hooks etc.

M & L for Earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0 mm as earth lead wire by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in Electrical plate No 3, SSR Part I- 2009 with 15 mm dia medium grade GI pipe as a protection and 20 mm dia medium grade GI pipe for watering purpose inlcuding funnel, wire mesh, RCC pit with cover complete and connected to earthing test point all as specified or indicated including testing on completion.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 4 core.

Excavation in trenches not exc. 1.5 m wide and not exc. 1.5 m in depth for foundation, cable etc. or for shafts, wells, cesspits, manholes, pier holes, pole etc. n. exc 10 sq m on plan and getting out in soft/ loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick with soils complete all as specified and as directed.

Removing of excavated material (soil) to distance not exc.50metres and deposited where directed at a level not exc.1.5 metre above the starting point complete all as specified and as directed.

Supply and laying 40mm outer dia, double walled corrugated (DWC) HDPE duct pipe conforming to IS- 14930 Pt-II with antirodent and non flame propogating properties of approved colour complete with fittings for cable protection complete all as specified and as directed.

Note : 1. Performance security:- Refer Condition 22 of Special Conditions. 2. Quoted Contract Sum shall be arrived at after deducting the amount of Credit Schedule (refer Schedule of Credit in pdf form for quantity, rate and amount etc.) for old unserviceable materials retrieved from site.

J P ASSOCIATES

R k construction

M/s Akshay Contruction

ganesh electricals and airconditioners

VISALAKSHI WATER PROOFINGCOMPANY PRIVATE LTD

Sai Construction

M/S Eknath agencies

ANIL CONSTRUCTION CO.