Construction of Multipurpose Social Center in Porur Chennai

Amount

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel,stoney earth and earth mixed with small size boulders SS.20B and Sand, silt or other loose soil, wet sand,or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water and cleaning and levelling the site etc.,complete -

0 m to 2 m Depth

Upto 2 m Depth

Supplying and filling in foundation and basement with Well Gravel in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Plain Cement Concrete 1:4:8 (one cement four fine aggregates and eight coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification

Providing and laying in position Standardised Concrete Mix M-35 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 400Kg/ cum in Cement and maximum water cement ratio of 0.45 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of Crushed Stone sand (M- Sand) but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requiremnents of IS standards.

In Foundation and basement - Below Ground Level

In Stilt Floor

In First Floor

In Second Floor

In Third Floor

In Terrace Floor - Fourth Floor

In Upper Terrace - Fifth Floor

Centering for soffits of RCC slabs of plane surface like lintels, beams ,etc.,including strutting 3m high using mild steel sheets of size 90cm X 60cm X and B.G 10 stiffened with M.S angles of size 25mm X 25mm X 3mm laid over silver Oak (C.W) joists of size 10cm X 6.5cm (spaced at about 90cm c/c )and supported dy casurina props of 10cm to 13cm dia (spaced of 75cm C/C) complying with standard specification and directed by the Enginner in Charge.

In Footing & Plinth Beam

For Roof Slab & Roof Beam

For RCC Column - Square or Rectangle & Lintel & Sunshade

For RCC Column - Circular

Centering for curved surfaces of all RCC items of work

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc.

Additional Strutting - Roof Slab & Roof Beam in Second floor - Double height Roof

Providing two legged scaffolding using 15cm dia casuarinas post of 4 M over all length (3 M Height + 0.5 M Projection + 0.5 M into the Ground) the distance between the two rows being 1.25 M and the spacing of posts being 2.0 M in both the rows with two horizontal posts with 0.5 M. Overlap on either side and braces at 2.0 M center to center including longitudinal and transverse middle braces to step up and providing a platform with country wood planks of 40mm thick and 1.M width, etc. in a complete from using coil and nails.(Rate for an initial height of 3 M and length of 1 M)

Suppling and fabricating and placing in position MS (or) R.T.S. bar for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors.

Post Tensioning Work: Design and execution of post tensioning work, including decoiling, the strands, cutting to the required lengths, supplying, laying of HT strands sheathing (GI corrugated ducts 0.3mm thick) jointing with couplers and inserting the strands, profiling, fixing liveend anchorages, including supply of stressing anchorages, suitable for 5-5 & 5-4 tendons, grout vents, making dead end anchorages, including flowering the strands, fixing tendon support bars, supervising the fixing of antibursting reinforcement, stressing the cables, end trimming, grouting the cables, with cement slurry, mixed with admixtures with required tools, plants, and machineries, and consumables etc.

(Shuttering, concreting & reinforcement steel shall be paid under respective items) at all heights including all leads, lifts, coordination, with the post- tensioning agency, preparation of drawings, obtaining approval from the Employer / Architect etc. Rate to include providing water, power, cement and admixture for grouting, packing of sheathing and anchorages blockings, filling of recess pockets after stressing using grouts (cement slurry mixed with approved admixtures) including providing access to post tensioning at all heights including all leads, lifts etc., all complete and as approved and as directed by the Employer Architect but excluding shuttering, concreting & reinforcement steel which shall be payable under respective items separately.

Brick work in CM 1:5 (one cement & Five Crushed Stone Sand (M- Sand)) using II class ground moulded bricks of size 9" X 43/8"X 2 3/4" including finishing, curing, etc., complete complying with standard specification

Upto Basement

Above Basement in Stilt Floor

In First Floor

In Second Floor upto Tie Beam Lvl

In Third Floor Above Tie beam as Third Floor

In Terrace Floor

In upper Terrace Floor

Brick Partition Walls using II class ground moulded chamber bricks of size 9"X43/8"X 23/4" in C.M 1:3 (One part of Cement and Three part of Crushed Stone Sand (M- Sand)) using hoop iron reinforcement,if found necessary standard specification including finishing, curing,etc., complete complying with standard specification.

In First Floor

In Second Floor upto Tie Beam Lvl

In Terrace Floor - Fourth Floor

Brick Arch work (Flat, Semi Circular or Segmental) in CM 1:3 (one cement & Three Crushed Stone Sand (M- Sand) using ground moulded chamber bricks of size 9"X4 3/8"X 2 3/4" standard specification including finishing, curing, etc., complete complying with standard specification

In First Floor

In Second Floor upto Tie Beam Lvl

In Second Floor Above Tie beam as Third Floor

Brick Arch work (Flat, Semi Circular or Segmental) in Partition Walls using II class ground moulded chamber bricks of size 9"X43/8"X 23/4" in C.M 1:3 (One part of Cement and Three part of Crushed Stone Sand (M- Sand)) using hoop iron reinforcement,if found necessary standard specification including finishing, curing,etc., complete complying with standard specification.

In First Floor

In Second Floor upto Tie Beam Lvl

In Second Floor above Tie Beam Lvl 32'6" Third Floor

Special Ceiling Plastering with cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 10mm thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications

Inner Plastering with cement mortar (1:5) 12mm ,thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications (S.I.306)

Outer Plastering with cement mortar 1:4 (One Part of Cement and Four part of Plastering Sand (P- Sand)) 20mm thick in all floors including cost and conveyance of all materials to site and labour charges etc, complete complying with standard specifications.

Plastering for bands including 115 mm thk Brick work in CM 1:3 as per the partion wall specification and plastering the band 4" X 4" with cement mortar 1:3 (One Part of Cement and Four part of Plastering Sand (P- Sand)) 12mm thick in all floors including cost and conveyance of all materials to site, finishing the corners and labour charges etc, complete complying with standard specifications.

Plastering for Cornice 3"X3" including Brick pitcning work in CM 1:3 as per the partion wall specification and plastering the Cornice 3" X 3" with cement mortar 1:3 (One Part of Cement and Four part of Plastering Sand (P- Sand)) 12mm thick in all floors including cost and conveyance of all materials to site, finishing the corners as per drawings and labour charges etc, complete complying with standard specifications.

Apply two coats of approved cement paint including cost of all materials to site and all labour charges for mixing applying and proper curring etc.

Painting two coats for Interior surface with approved Interior Plastic Emulsion paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification.

Painting two coats for Exterior surface with approved Exterior Plastic Emulsion paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification.

Painting two coats with Ready Mixed Enamel Paint over the new iron works of approved quality and colour without priming coat including the cost all materials etc.,complete, in all floors.

Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding,grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification

Paving the floor with Double charged Vitrified tiles of approved quality and colour of size 600x600x8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality of tiles should be got approved by Municipal Engineer before use on work

Paving the floor with design Antiskirt ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick laid in-situ and pointed with same coloured cement

Dadooing walls with Glazed tiles of sizes 305mm X 200mm X 6mm size of approved make and quality and colour Set in cement mortar 1:2 (One part of Cement and two part of Plastering Sand (P- Sand)) over 10 mm base layer plastering and pointing with white cement neatly as directed.

Supply and laying flooring with best quality the following materials of Machine Polished granite slab not less than 18 mm thick (Jet Balck) in CM 1:4 (1 of cement : 4 of manufactured sand) 20 mm thick including finishing the joints with white cement slurry, cutting, edge chamfering to approved shape and polishing rough, medium, nice and tin-oxide polish. The rate including cost of all materials, labour charges, wastages, necessary lead and lifts working at all levels, transportaion charges, loading & unloading, preparation of surface, ncessary haccking in RCC surface, cutting to required shape, edging, tools and plants, fuel, curing, cleaning, acid wash over finished surface, protection with Gypsum / Pop layer over plastic sheet and removing the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Supply and Laying flooring with best quality approved colour 18mm thick Flamed Steel Grey Granite Slab for Staircase and Ramp flooring of size not less than 1200 x 600 mm machine cut and set in C.M 1:4 (1 of cement: 4 of manufactured sand) 20 mm thick topped with white cement slurry (tor surface contact of the bottom of the granite slab) as per approved pattern, Including tinishing the joints with matching shade cement slurry, cutting, edge chamfering and polishing rough medium, nice and tin-oxide polish.Rate including all materials, labour charges wastages, necessary lead and lifts, working at all levels, transportaton charges, loading, unloading. preparation of surface, ncessary haccking in RCC surface, cutting to required shape, edging, antiskid grooves,tools and plants, fuel, curing, cleaning, acid wash over Finished surface, protection with Gypsum/Pop layer over plastic sheet and removing the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge

Polishing and Nosing the Granite Slab To Half Edge to round shape and finishing the surface neatly etc. complete complying with standard specification as directed by department officers

Nosing of Granite - Single Nosing

Nosing of Granite - Double Nosing

Grooving on the Granite Slab for steps as non slippery effect of 5mm in size and cleaning, finishing the surface neatly etc. complete complying with standard specification as directed by department officers

Stainless Steel Handrail 900mm high Providing and fixing stainless steel handrail 900mm high (as shownin drawing) made out of stainless steel conforming to SS 304 with 8%to8.5% nickel using 50.8mm outer dia at top (with 1.6mm wall thickness) and 38.10mm(1.6mm wall thickness ) stainless steel pipe placed vertically at 1m centre to centre and two horizontal SS pipe 25.40mm outer dia (with 1.2mm wall thickness) welded at a distance of 300mm using TIG welding process with 308L SS electrode (in station building all flooor staircases) with necessary bends, flanges and base plates. Rate is inclusive of all materials, labours, lead, lift,etc. as directed by Engineer in-charge.

Supplying and filling the sunken slab area by BRICK-BATCOBA by adding CICO NO:1 of approved equivalent admixture including applying two coats not less than 2 mm thick of TAPECRETE- Acrylic Polymer Based Naterproof Coating, over the final coat of cement plaster 12 mm thick with cement sand mortar 1:3 mixed with water proofing compound like CICO No.1 at the rate specified in the manufacturer's specification after entire completion of laying pipes, sanitary fittings etc Rate including all mater aaod and lifts, working materials, labour charges wastages with necessary lead and at all levels, protecting the laid pipes and sanitary fittings, finishing the surface smooth to receive the top coat of water proofing application etc. as complete with all respects complying with relevant standard specificatior and as directed by the Client/ Engineer-in Charge

Including applying two coats not less than 2 nm thick of TAPECRETE- Acrylic Polymer Based Waterproof Coating, over the plastered surface as including final coat of cement plaster 12 mm thick with cement sand mortar 1:3 mixed with approved water proofing compound like CICO No. 1 or approved equivalent conforming to IS 2645 at the rate specified by the manufacturer over coated surfacepreparation of surface, finishing, curing etc. all complete at all levels as per manufacturer's specifications and as directed.

Terrace Waterproofing Supply and laying water proofing treatment for terrace covering the following order and consisting of following operations. i) Making V' grooves at the construction joints of size 20 x 20 mm and filling the "V" Groove with CICO No. 3 Quick Setting Waterproofing Compound admixed with cement.The roof slab gutter slab shall be thoroughly cleaned to remove debris and dust, and applying 2 coats not less than 2 mm of polymer based Elastomeric Coating like TAPECRETE - RTU compound and cured for 7 days and followed by a layer of 20 mm thick cement mortar 1:3 admixed with CICO NO: 1 (or) other approved equivalent make shall be spread over the prepared surface

The gap cement mortar 1:4 admixed with compound like CICO NO:1 or approved equivalent afterwards curing shall be carried out for two days a final layer of cement mortar of 1:3 admixed with water proofing compound like CICO NO:1 or approved equivalent make shall be laid to a thickness of 20 mm and draw a false line of 300 mm x 300 mm.

The parapet side wall / gutter wall shall be thoroughly cleaned to remove all dust particles and a layer of 15 mm thick C.M 1:3 shall be laid to a height of about 300 mm above the top of the terrace/Gutter slab on the Parapet / Gutter side wall admixed with water proofing compound like the CICO NO:1 or approved equivalent make. Providing, supplying, mixing, applying two coats of ready to use two component Acrylic polymer modified cement based, flexible, water proofing slurry like or approved equivalent to a thickness of 2 mm over the plastered surface of operation as per manufacturer's specification and as directed.

Providing Pre – Constructional Anti – Termite Treatment and creating a Chemical Barrier to the building by injecting chemical emulsion of required concentration under grade slab and grade beam, all round the footings, column pits, trenches, pits, tunnels, wall trenches, back fill, plinth filling,Retaining/side walls of basement floor, external perimeter of building, surrounding of pipes, expansion joints, below U.G. sump and retaining/side walls etc. as per instructions of chemical manufacturer and all as directed. The treatment shall be carried out strictly in accordance with the technical specification and conforming to IS 6313 or equivalent BS specification. The chemical to be used as insecticide for the treatment shall be Biflex Tc, TC stands for Termiticide Concentrate for Termite Control (Bifenthrin) and the application shall be diluted 1 part of chemical Biflex Tc with 49 parts of water to get 0.05% emulsion and strictly in accordance with the manufacturer’s specification. The chemical to be used for the treatment and concentration of the chemical solutions should be as laid down in IS - 6313 Part II

Weathering Course with Concrete Broken Brick (S.I.No.278) & ( P & D) Data 54.Jelly 20mm gauge in pure slaked lime (no sand to be added) over roof slab,the proportion of brick jelly to lime being '32 to 12.5 well beated with wooden beaters for giving required slope and thickness as directed by the departmental officers etc., complete.-10 cum

Finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 20 mm of approved quality in Cement Mortar 1:3 (One Cement add three sand) 12 mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cem

Best Indian Teak Wood panelled and glazed door in double shutters with glazed head. The size of frames shall be 100x75mm at side,verticals,top transom and centre vertical for head. The height of glazed head is 40cm using 595 gm.glass panes for head. The shutters shall be of 40mm thick with moulded panels in 20 mm thick planks for the panelled portion and 595gm.glass panes for the glazed portion. 6Nos.of iron hold fasts fixed in C.C.1:2:4. 6Nos.of butt hinges 125mm long including wind appliances, furniture iron fittings.1No.of iron padlock 15cm long for locking arrangements and fixing in position with 2Nos.of 20mmdia M.S horizontal bars for the head portion, etc., complete. (ISISTD)

Flush doors : Supplying and fixing Double leaf flush door 32/30mm thickness poth side commercial ply and approved brand Century/ Merino/ Greenlam with T.W.frames of size 100x75mm at side verticals and top, 6Nos.of iron hold fast fixed in C.C.1:2:4 and 3Nos.of butt hinges 125mm long including wind appliances furniture iron fittings 2Nos.of iron pad lock 15cm long for locking arrangements and fixed in position as directed during execution.(ISI STD)

Flush doors : Supplying and fixing single leaf flush door 32/30mm thickness poth side commercial ply and approved brand Century/ Merino/ Greenlam with T.W.frames of size 100x75mm at side verticals and top, 6Nos.of iron hold fast fixed in C.C.1:2:4 and 3Nos.of butt hinges 125mm long including wind appliances furniture iron fittings 2Nos.of iron pad lock 15cm long for locking arrangements and fixed in position as directed during execution.(ISI STD)

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 25GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with spag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown olour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the executive Engineer before use on work

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Supplying & fixing door shutters for Medium Density Fiber Board of exterior grade 35 mm thick,single leaf conforming to IS:12406/1989 with 35x12 mm T.W.Lipping on all edges with necessary adhesives and CP screws complying with standard specifications. The rate is inclusive of threee coats of best quality varnish but excluding cost of furniture fittings.such as 300 mm tower bolt 2nos,200mm towerbolt I no. 300mm Aldrop 1 No. Alu handle ornamental type 2 Nos,and 1 No. Door stopper etc complete.

Solid PVC door shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rebate for housing the shutter.

Supplying and Erecting Pull and Push Type Rolling Shutter with ISI make of approved size and section sing 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc Manuallay Operaeted Rolling Shutter

FALSE CEILING WITH GYPSUM BOARD Providing and fixing suspended false ceiling using SAINT - GOBAIN GYPROC or Equivalent make which includes providing and fixing GI perimeter channel of size 0.50mm thick having one flange of 20mm and another flange of 30mm and a web of 27mm along with perimeter of ceiling, screw fixed to brickwall / partition with the help of nylon sleeved and screws at 610mm centres. Then suspending GI intermediate channels of size 45mm, 0.9mm thick with two flange of 15mm each from the sofit at 1220mm centres with ceiling angle of width 25mm x 10mm X 0.55mm thick fixed to sofit with GI cleat and steel expansion fasteners. ceiling section 0.55mm thickness having knurled web of 51.5mm and two flanges of 26mm each with lops of 10.5mm are then fixed to the intermediate channel with the help of connecting clips and in direction perpendicular to the intermediate channel

Dismantling removing the existing Reinforced Cement Concrete work etc., by using required mechinaries including stacking of steel bars and disposal of unserviceable material within 50m lead, labour charges, as per direction of Engineer in charge.

Dismantling removing the existing Plain Cement Concrete work etc., by using required mechinaries including stacking of steel bars and disposal of unserviceable material within 50m lead, labour charges, as per direction of Engineer in charge.

Dismantling brickwork manually by mechanical means including stacking of serviceaboe material and disaposal of unservice material within 50 meters lead as per direction of Engineer in charge.. (Under 3m Height)

Clearing the grabbing the site, This work shall consist of cutting, removing and disposing of all materials such as trees, bushes, shrubs, stumps , roots, grass, weeds, lop organic soil not exceeding 150 mm in thickness, rubbish etc., which in the opinion of the Engineer are unsuitable for incorporation in the works, from the area of road land containing road embankment, drains, cross-drainage structures and such other areas as may be specified on the drawings or by the Engineer., It shall include necessary excavation, backfilling of pits resulting from uprooting of trees and stumps to required compaction, handling, salvaging, and disposal of cleared materials. Clearing and grubbing shall be performed in advance of earthwork operations and in accordance with the requirements of these Specifications.

Clearing the Light jungle

Refilling with excavated soil (other than sand) complying with standard specification in layers of 15cm watered well rammed and consolidated in the sides of the foundation, Plinth beam, Basement etc., and removing and depositing the surplus earth complete as directed by the Engineer-in-charge.

Carting away surplus excavated earth available with in the campus is to be carted to a lead of within 5 KM from site. The rate shall include loading into the tipper/ lorry transporting and unloading, leveling and the earth scooped by bulldozers grading etc.,complete with all respects complying with relevant standard specification, as directed by the Departmental Officers. Rate to include materials, loading, unloading, transportation, plant and machinery, hire and fuel charges for tools and plants and other incidental charges, royalties, seignorage and taking statutory approvals as necessary to carry out the work as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

Providing of Granular Sub base using Grade I materials of table 400 -1 of Morth with minimum CBR 30 spreading in uniform layers with motor grader on prepared surface, mix in by palce method at OMC and compacting with Vibratory Roller to achieve the desired density including all labourcharges etc, complete as per technical specification and as directed by the departmental officers. Morth - Rev V No. 111,112,401,900

Providing and laying, spreading and compacting graded stone aggregate to Wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant carriage to mixed material by tipper to site laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achive the desired density complete as per clasue 406 of MORTH specifications.

Supplying and laying Rubberised interlocking Paver block M40 grade Providing and laying of 83mm thick high strength type conforming IS 15658-2006 of rubberized interlocking paver lock in size of minimum compressive strength of 40N/mm2 in uniform shape of approved make to be laid in flurring bone pattern with sand cushion below the uniform shap of approved non skitting surface in the top and the rate including levelling the base preparation of pavers as sub base, sand cushion 150mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers,sweeping tranporting loading unloading of laying paver block as per standard specification,.

Providing enamel indication board with proper male or female figure of size 35x30cm as directed.

Manufacturing, Supplying and fixing Brass cut letters of size 30cm height and 18mm thick. (Rate as per quotation inclusive of all Labours, Material & Transportation)

Providing and laying non-pressure class NP2 RCC Spun pipes with collars including excavation of trenches in soil/murum/rock, laying the pipes as per layout and drawing, filling the joints with stiff mixture of cement mortar (1 part cement :1part fine sand) and jute, curing, testing the pipe and refilling the trenches in layers with due compaction & watering etc. complete as directed

Supply and fixing in position white European Water Closet of approved make with low level flushing tank 10 litre capacity of best quality and approved make with 100mm P or S trapwith double flapped rigid PVC seat cover with CP brass hinges etc. complete complying with standard specification and as directed by the Departmental officers (The EWC should be got approved by the Executive Engineer before use on works.

Supplying and fixing of CP Two Way Bib Cock with Health Faucet ,wall hook & one metre long flexible tube including cutting and making good the walls wherever required etc complete. complying with standard specification and as directed by the Department officers. The quality and make of health faucet should be got approved by Concern department Engineer before use on work.

Wash Hand Basin of size 550 mm X 400 mm with all accessories such as cast Iron Brackets, 32 mm Dia C.P. Waste coupling, Rubber plug and Chain, 32 mm dia ' B ' Class G.I. Waste pipe, 15 mm Dia G.M Wheel valve; 15 mm Dia Nylon connection, 15 mm Dia Brass Nipples, 15 mm C.P. Pillar tap etc.,including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and as directed by the Department officers. The quality and make of below counter Wash basin should be got approved by department Engineer before use on work. ( all Inclusive of cost of basin, Bottle Trap and Angle Cock)

Supplying and fixing Lipped Mouth Porcelain Flat Back Urinal(white colour) of size 26.5x31.5x44cm with all accessories such as 32mm dia Bell Mouth PVC Connection, 15mm dia GM Wheel Value, 15mm dia 'B' Class GI Waste Water Pipe, 15mm dia Nylon Connection, 15mm dia Brass Nipple, and suitable screws, shellac etc., complete. The rate including cost of all materials, labour charges for fixing and transportation etc. completed as directed by Engineer- in-Charge.

Providing and fixing in position vertically marble partition in the urinals with Raj Nagar marble stone of white hard, dense hemogenious colour without cracks, and fissures of size (3.0+2.0)5'height thickness varies from 18 to 20mm including making grew in the wall and pointing and packing with cement mortar 1:3 polishing, finishing on both sides etc., as directed at site. (GCC BD-874)

Supplying and fixing Cp towel rail 600mm long and 20mm diameter with brackets of same materials including cost of teak wood plug and CP screws etc., complete complying with standard specification and as directed by the Departmental officers.

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed Various Sized and 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks) .

Size 600X450X5.5mm Thk

Supplying and fixing heavy duty 15mm CP shower unit comprising of CP 15mm dia hot & cold mixer with CP spout, overhead shower set comprising of CP shower arm, rose etc.,complete with CP wall flanges. The rate including cost of all materials, labour charges and transportation etc. completed as directed by Engineer- in-Charge.

Supplying,installing,testing and commissioning of approved make CONCEALED STOP COCK including neccesary accessories etc, complete,works include making require size curout in wall,and fixing the control box property,redoing the same etc,complete the quality and make of concealed stop cock should be got approved by concern department Engineer before use on work.

Supplying and fixing the best quality approved make of Angle Cock with wall flange including cutting and making good the walls wherever required etc. complete complying with standard specification and as directed by the department officers. The quality and make of angular stop cock ahould be got approved by concern department engineer before use on work

Supplying and fixing the best quality approved make of C.P. Soap Tray/ Dish of size of 150mmx100mm with wall flange including cutting and making good the walls wherever required etc. complete complying with standard specification and as directed by the department officers. The quality and make of angular stop cock ahould be got approved by concern department engineer before use on work

Supplying & fixing in position 15 mm dia brass/ C.P pillar tap (Heavy duty) of approved make conforming to I.S. Specifications & quality including cost of shellac, thread etc., complying with standard specifications & including cutting & threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the work).

Supplying & fixing in position 15 mm dia PVC Bib Tap of approved make conforming to I.S. Specifications & quality including cost of shellac, thread etc., complying with standard specifications & including cutting & threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the work).

Automatic Electrical Water Heater with copper container, with Glass Wool / Puf Insulation with MS powder coated shell suitable for 25 Litres capacity 230V / 1000W (Lower End)

Supplying and fixing in position PVC cowls of following dia of best approved quality conforming to BIS, etc., complete complying with standard specifications. (The PVC cowl should be got approved by the Executive Engineer before use on works).

160mm Dia

110mm Dia

90mm Dia

75mm Dia

Supplying & fixing in position PVC Nahini / Floor trap of size 100x75mm including stainless steel gratings of approved brand & quality, fixed over a bed of brick jelly lime concrete 1:2:5 ( One part of lime, two parts of sand & five parts of 40 mm size brick jelly ) & finished with cement mortar 1:3 ( One cement & three sand ) including dismantling masonry works wherever found necessary & making good the damaged portions to the original condition & giving connections to the cast iron pipes etc., complete, complying with standard specification. (The PVC Nahini / Floor trap should be got approved by the Executive Engineer before use on works ).

Supplying & fixing in position 150 X 100 mm square mouth 'P' or 'S' trap stone ware Gully trap 'A' grade with cast iron gratings of size 300 X 300 mm with C.I. air tight cover with frames of size 300 X 300 mm at bottom & top respectively with necessary earth work excavation, laid over a bed of brick jelly cement concrete 1:3:6, 150 mm thick using 20 mm size broken brick jelly including necessary block work & plastering, &including dismantling masonry wherever necessary & redoing the damaged portions to the original condition & by using cement concrete 1:3:6 using 20 mm stone jelly for fixing the Gully trap & giving connections to the stone ware sewer line etc., complete, complying with standard specification. (The stone ware gully trap should be got approved by the Executive Engineer before use on works ).

Making Through holes in plain or Reinforced Cement Concrete with Diamond Core drilling system by using Bosch Power Tools of Following Diameter in Various thickness and Dia

100mm Dia 300mm Thk

150mm Dia 300mm Thk

Supplying,installing,testing and commissioning best quality approved/equivalent make of Single Bowl with drain board 1200X550X180 mm stainless steel sink with brass Chromium Plateds wivalty peex tended swing sink cock 32mm dia CP waste coupling, 32mm dia heavy duty waste hose with extension pipe, 15mm CP angle valve with CP inlet connection tube,CP wall flange, including necessary bracket set ccomplete complying with standard specification and as directed by the Department officers.The quality and make o fsink and brass CP coated swiv al type sink cock should be got approved by Concern department Engineer before use on work.

Constructing brick masonry manhole with second sort Solid Blocks in CM 1:5 (one of cement, Msand) including earthwork excavation and sand filling for a depth of 150mm top cover slab with CC 1:2:4 (one of cement, two of sand, four of graded aggregate) 20mm nominal size for fixing C.I Frame, including shuttering, reinforcement foundation concrete 1:4:8 (one of cement, four of sand, eight of graded aggregate 40mm nominal size) 100mm tk., plastering inner, outer and other exposed surface with 15mm tk., cement mortar 1:3 (one of cement, three of sand) and finishing with a floating coat of neat cement with water proofing compound as per specification, making channelsin CC 1:2:4 (one of cement, two of sand, four of graded aggregate) neatly finished including fixing C.I. Cover and frame, C.I. Rungs etc., complete complying to standard specification.

Supply and fixing RCC precast slab manhole cover SFRC of 50mm thick and required size 900mm x 900mm made in CM 1:3 Ratio both direction including cost and conveyance of all materials, labour and transportation etc complete complying with standard specification.

Supplying and fixing in position the best quality and variety sizes PVC soil and waste pipes 6Kg /10Kg / cm2 of ISI mark, providing leak proof joints etc and making connection to all sanitary fittings, including dismantling masonry / RCC works wherever necessary and making good the portions. The quality and make of PVC pipes and specials should be got approved by Concern department Engineer before use on work.

160mm Dia Pipe

110mm Dia Pipe

90mm Dia Pipe

75mm Dia Pipe

40mm Dia Pipe

Supplying, laying and jointing UPVC pipes of approved quality and best variety conforming to ISS and with ISI mark of the following size including cutting, threading and fixing PVC specials but excluding cost of such specials and fixing to wall with necessary teak wood plugs, PVC clamps and screws, making good the portions to original condition with necessary brick work and concrete plastering wherever necessary with necessary scaffolding charges etc. complete complying with standard specification and as directed by the Department officers. The quality and make of UPVC pipes and specials should be got approved by Concern department Engineer before use on work.

20 mm dia UPVC pipe

40 mm dia UPVC pipe

Supplying, laying and jointing CPVC pipes SDR 11(having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing CPVC specials using CPVC adhesives and fixing into wall with teak wood plugs, CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The CPVC pipes shall be got approved by Executive Engineer before use on works. (Internal)

20 mm dia CPVC pipe

40 mm dia CPVC pipe

Supplying & fixing in position first quality & approved variety of various dia U.P.V.C Ball Valves ( Heavy type ) with I.S.I. Mark of the following size including cost of Shellac, thread etc.,including labour for cutting & threading of Pipes etc., complete complying with standard specifications for both internal & external water supply arrangements.

Cost of 40mm dia U.P.V.C Ball Valve (quotation)

Supplying and fixing in position first quality and approved variety of Gun Metal /brass valve /airrelease valve /Check valve (Heavy type)with ISI mark of the following sizes including cost of Shellac,thread etc,including labour for cutting ,threading and fixing position of CPVC Pipes for both internal external water supply arrangements etc,complete complying with standard specification and as directed by the Department officers. The quality and make of valve should be got approved by Concern department Engineer before use on work

Drilling of 12" dia vertical borewell so as to have a finished size of 6" dia borewell in boulder area to any required depth as decided by the TWAD Board Officers including Transportation from one place to anothr place with in Tamilnadu State by direct or reverse rotary mud circulation method using Contractor's rig tools, fuel, labourers, bentonite mud and water required for drilling at the site shown including construction of mud pit etc. using only calyx rigs.

300mm (As per Twad Schedule Item No: 14f, P.No: 306)

150mm / 165mm (As per Twad Schedule Item No: 14a, P.No: 305)

Reaming from 200mm dia pilot bore upto 350mm dia bore as direct by the Engineer incharge up to 80mtr depth ending below ground level. (As per Twad Schedule Item No: 7f, P.No: 301)

Supply and laying following dia PVC casing pipe with excise duty as per IS 12818 / 1992 ( 1.1 (4,6,3), P.No: 22, Twad

200mm dia CS

200mm dia RS

150mm dia RS

Labour charges for inserting PVC casing pipes assembly (with slots or without slots) in the drilled hole including jointing the pipes with PVC couplers with cement paste etc., complete, supply and packing the annular space with pebbles of size and quality as approved by the Executive Engineer of Departmental

200mm dia CS

200mm dia RS

150mm dia RS

Charges for developing the borewell with air compressor of 300 CFM capacity (Minimum 8 Hours) including transportation labour and fuel charges for compressor as directed and conducting yield test by 'V' notch method.

Supply ,erection and testing & commisioning of 3HP submersible pumpset in the to suit 200mm borewell of capacity of 4800 LPH @ 265Ft, max. total head of 280 Ft pumps fitted with bronze impellers and having delivery size of 40mm - 430V along with 3mts cable and manufactures standard control panel which is mandatory and as directed by the officer incharge and other required supporting items like SS hose nipple, nylon rope, clamps, bolt and nuts,GI nipple, 50mm dia HDPE hose of required length etc completed and as directed by the officer incharge.

Supply ,erection and testing & commisioning of 2HP submersible pumpset in the Open borewell of capacity of 2.5 LPS @ 65Ft, max. total head of 80 Ft pumps fitted with bronze impellers and having delivery size of 40mm - 430V along with 3mts cable and manufactures standard control panel which is mandatory and as directed by the officer incharge.

Labour charges for the erection of submersible pumpset in borewell/openwell including fixing and jointing submersible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TPICN switches starter, Voltmeter, Ammeter, three pilot (indicating) lamps capacitor single phasing preventor, water level guard and laying and jointing the cables and twin earthing as per IE rules etc., complete and testing the pumpset and trailrun for 10 days. (TWAD 17C)

Supplying and erecting in position of following liters capacityIndustrial Model Reverse Osmosis Water-cum- Purifier todeliver Potable Water with World Health Organisation (WHO)Standards with following accessories.(a) MS Skid - 1 No.(b) Media 11054 No. Vessel with 20 nb Multiport Valve (withMedia Pubble and Fine Sand and Activated Carbon Filling) set(c) Feed Pump 0.50 HP – 1 No.(d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No.(e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic(USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No.& Pressure Gauge - 2 Nos.(f) Flow Meter - 1 No. 20” Filter with Housing - 1 No., LowPressure Switch - 1 No., Level Switch - 1 No. & NecessaryCPVC Pipes and Fittings.The system shall be provide with Two Panel Control Systemwith necessary Stainless Valves and Fittings and Float Controletc. The rate should be inclusive of all civil works, wherevernecessary to install the System in position and intact.

Providing & Fixing Toilet Cubicle System in SS-316 MEDIUM Series - Shoe System of size Width 900mm x Depth 1500mm x Height 1930mm, Door Size - 600mm x 1830mm, Divider Height - 1830mm, Comprising of Rigid SS components: (1) SS316 Indicator Lock (2) SS316 Height Adjustable Legs (3) SS316 Door Knob (4) SS316 Coat Hook & Aluminum (Brush Finish): (5) Shoe Box with Cap (6) Top Rail (7) h Section (8) U Section (9) Silicon Strip to be inserted in h Section to provide Noise Dampening (10) Screws & Plugs with (11) Water, Chemical, Heat, Bacteria, Fire, Impact & Scratch Resistant 12 mm T Line High Pressure Compact Laminate. The 12mm HPL to have a minimum density of 1350 kg/m3 with a warpage limit of .5% of its length. The Top Rail will be fixed end to end and all the mid and end pilasters will get fixed into it. Shoe box will only be fixed on the Front Panels and not in dividers. U Sections will be used for Board to Board Jointing and Board to Wall Fixing.

Providing & Fixing Urinal Partition with SS Clamp which has a interconnection between which the Water, Chemical, Heat, Bacteria, Fire, Impact & Scratch Resistant 12 mm T Line Compact Laminate will be fixed and the other side of the clamp will be screwed in the wall from both sides.

Construction of Rain water Recharge well (1500mm dia) as per the drawing with necessary connections, Earth work - digging the well for recharge well. supply and installation of Reinforced concrete Rings - 5 feet OD & 1 feet Height, 50 MM Thick - 10 no's. supply and installation of Reinforced concrete slab- 5 feet in dia, 200 mm thick, and 25 mm perforated - 8 mm mild steel rods used for reinforcement -1" Perforated - 1no's.supply and installation of Reinforced concrete closing slab - 3 feet in dia OD, 75 mm thick, 8 mm mild steel rods used for reinforcement with 600mm x 600mm Square FRP/Plastic manhole cover - 1no's.supply and installation of MS grating - 6*6inch square - 2no'sFiltration Media Installation For recharge Well Unit: 40 mm crushed stones - 0.12cum, 20 mm crushed stones - 0.12cum, Brick Bats - 0.12cum, Mixture of Brick Bats and Gravels for filling the gap between excavated earth and RCC rings- 1.6cumShifting of excavated earth to the approved / authorised dumping yard as directed by the authorities / Site in charge.

supply and installation of `V' WIRE SCREEN - 0.75 mm Slots. SS-304 Material - 0.5 mtrs Height - 6 " diameter - 2no's Drilling a bore well - 200mm dia by high speed compressor- 4MTRS. supply and installation of 110mm PVC PIPE PN-6 - 4 rmtr, 110mm PVC PIPE PN-6 Perforated with 10 mm Zigzag holes to easy percolate the water - 4 rmtr, 12mm Gravel Packing between bore well hole and PVC pipe and Inserting into the Bore Well- 4 mtrs. supply and installation of - 180GSM Gio-fabric sheet to cover V-Wire screen,Shifting of excavated earth upto 1000mtrs as directed by Engineer in charge.

11kV HT Outdoor RMG Panel Supply,Installation,Testing and Commissioning of OUTDOOR Weather & Dust proof Type, floor mounting, free standing type 11KV Ring Main Gear unit made out of M.S sheet steel clad dust and vermin proof with 630A Copper Busbars, Interconnections, necessary protections, Measuring Instruments, Indicating Instruments, necessary Protection Relays, CTs, PT with necessary control fuses/MCBs, Termination arrangements for Incoming and Outgoing Cable of as per EB authorities approval ,earthed cable, Terminal Blocks, Earthing, Powder coated painting, Sign writing and Base channels etc., with complete all accessories as required for satisfactory operations and as per the detailed Technical Specifications enclosed and as per TANGEDCO Requirements comprising of the following. Remote Communication and operation

INCOMER:

11kV,25KA 630A, Load break Switch with necessary required accessories - 1Nos

OUTGOING :

11kV, 25KA 630A, vacuum Circuit Breaker with necessary required accessories : 1No

The RMG panel shall be manufactured as required by the electrical authorities with all necessary approval approval shall be obtained including testing & commissioning and any additional features required by the supply authorities shall be carried out at no extra cost. Rate shall inclusive of factory witness test as specified in the technical specification and all necessary test to satisfy the Tangedco /CEIG Requirements.Erection shall inclusive of foundation and Base channels etc., with complete all accessories as required for satisfactory operations and as per the detailed Technical Specifications enclosed and as per CMDA/TANGEDCO/CEIG Requirements . Remote Communication and operation facility should be incorporated as per TANGEDCO requirements.

At EB Room

11KV Outdoor HT Panel Supply,Installation,Testing and Commissioning of 11KV Outdoor type floor mounting, free standing 11KV HT Panel, RMU,25KA, 630A VCBs 1 no as incoming and RMU,25KA,630A VCB-2nos as outgoing and with all accessories complete as required following:- a) Protection relay: 27,50,51,51N, 59,81,86,94. b) Manually Charged Spring Closing mechanism, c) set of mechanical close /trip knops. d) Spring charge indicators. e) 2-5A Overload Trip Shunt with time limit fuses calibrated for 75-150% and shunt with limit fuse. f) 1 no of operator counter. g) 3 nos cast resign current transformer with secondary ratio of 100/1A for incomer & 50/1A for Outgoing , class 0.5/5p20,15VA burden rating protection and metering. breaker shall have all protective and auxiliary relays with alarm annunciation. h) Potential Transformer11KV/110V,50 VA, for class 0.5 metering and class 3P for protection. i) provision for mounting sealing kit suitable for HT XLPE cables. j) 11KV class 630a 25KV VCB draw out Type. k) Built in DC power supply pack of suitable capacity.

The Panel made out of M.S sheet steel clad dust and vermin proof with 630A Aluminium Busbars, Interconnections, necessary protections, Measuring Instruments, Indicating Instruments, Protection Relays, CTs, PT with necessary control fuses/MCBs, Termination arrangements for Incoming and Outgoing Cable of 11 kV 3Core 240 Sq.mm XLPE Alu. Armoured earthed cable, Terminal Blocks, Earthing, Powder coated painting, Sign writing and Base channels etc., with complete all accessories as required for satisfactory operations and as per the detailed Technical Specifications enclosed and as per TANGEDCO Requirements also and as comprising of the following.

11kV, 630A, 25KA VCB (Vacuum Circuit Breaker)with necessary required accessories - 1 No

OUTGOING :

11kV, 630A, 25KA VCB (Vacuum Circuit Breaker)with necessary required accessories - 1 Nos

With necessary Aluminium busbars and meterings as per shown in the drawing ,phase indication lamp, MCB and switch control etc. with provision for accommodating 11 kV, PT, CT meterings, energy consumption metering, all protection relays with necessary C.T. as per the detailed specification & Single Line diagram attached. Panel should be extendable type. The HT Panel shall be manufactured as required by the electrical authorities and approval shall be obtained including testing & commissioning and any additional features required by the supply authorities shall be carried out at no extra cost. The Panel shall be designed for extendable in future. Note:-The panel should be having provision to compatibility with IBMS. Rate shall inclusive of factory witness test as specified in the technical specification and all necessary test to satisfy the TANGEDCO/CEIG/CLIENT Requirements. Erection shall inclusive of foundation and Base channels etc., with complete all accessories as required for satisfactory operations and as per the detailed Technical Specifications enclosed and as per CMDA/TANGEDCO/CEIG /PWD Requirements.

Rate shall inclusive of factory witness test as specified in the technical specification and all necessary test to satisfy the TANGEDCO/CEIG Requirements. Erection shall inclusive with complete all accessories as required for satisfactory operations and as per the detailed Technical Specifications enclosed and as per CMDA/TANGEDCO/CEIG Requirements.

EB Incomer:

400 Amps 4 Pole 50kA EDO microprocessor based electrically draw out type Air circuit breaker with shunt release shutter assembly, door interlock and all other accessories with three over current and one earth fault releases as shown in the Electrical schematic drawing.

Each Incomer shall have

1 No. 400A/5A CT with CL: 1 5P10,15VA with suitable control fuse For APFCR RELAY in the capacitor panel, and CT for REF for Transformer Neutral to be incorporated as per SLD

1 No. Spike Protection Device with connected with suitable control fuse(Type B+C)

1 No.Maximum Demand controller and 1 No. Digital type Multifunction meter with RS Port and connected with 1 No..400A/5A CL.1 15VA CT

1 Set.of 2 overcurrent and 1 Earth fault relay are connected with 1 NO.1600-/5A CL.5P10 15VA CT

Master Trip relay & Stand By Earth fault relay, over voltage relay with all related connected accessories.

1 Set of 'RYB' and 'ON','OFF','TRIP' indication lamps connected with suitable control fuse

DG Incomer:

400 Amps 4 Pole 50KA microprocessor based electrically draw out type Air circuit breaker with shunt release shutter assembly, door interlock and all other accessories with three over current and one earth fault releases as shown in the Electrical schematic drawing.

Each DG Incomer shall have

1 No.Digital type Multifunction meter with RS Port and connected with 1 NO.400/5A CL.1 15VA CT and necessary protection CTs as per SLD

Bus coupler:

1 No. 400 Amps 4 Pole 50KA EDO ACB without releases

Interlock Arrangements:

Both EB & DG incomers and Bus coupler shall be electrically and mechanically interlocked through burden rope as per the Truth Table mentioned in the SLD and should be compatible to PLC(Programmable Logic Controls.) operations. I/C of DG,Transformer and Bus Coupler should be suitable to all type of conditional operation. Necessary control should be incorporated to the Client requirement and safety operations. All control circuits should fail safe condition to be incorporated.

BusBar:

400 Amps TPN 50KA Al. busbars : Current density consider 0.8 Amp/1Sq.mm. Neutral Busbar shall be the same size of Phase busbar.

Earthing : 2R 50 x 6mm Aluminium flat

OUTGOINGS

All incoming and outgoing breakers should have over current, Time adjustable short circuit and earth fault releases. Necessary Flange connection for Bus duct entry to be included. All the Outgoing feeder shall be ON/OFF/Trip status for BMS , indication lamps , & MULTIFUNCTION METER , with emergency lockable push buttons, all ACB and MCCBs should have one (spare) potential free contactor, Combined digital type Multi function meter with LAN port. Each LAN port of the meter connected through individual cable. , The rate shall inclusive of necessary CTs, control switches, Front operating handles etc., All switch boards shall be fabricated as per the detailed specification enclosed. Suitable size outgoing cable chamber and extra busbars should be provided for connecting the number of outgoing cables as per the schematic drawing. 320A MCCB Switch - 2Nos 250A MCCB Switch - 3 Nos 160A MCCB Switch - 1 Nos 100A MCCB Switch - 2 Nos

The transformers incomer, DGs incomer shall be provided with protection relays such as IDMT (2O/C + E/F), REFR with CTs at transformer side (Restricted Earth fault Relay), Both the incomers and bus coupler should be interlocked with mechanical and electrical arrangements by hardware control wiring along with PLC (Programmable Logic Controls). The Hardware control wiring & PLC operation shall be feasible to extend for future 2 incomers and bus couplers, and all as per the detailed specification and drawings enclosed.

Energy Monitoring/breaker monitoring software: All incoming and outgoing breakers should monitored from Display units - Model number similar to Schneider make FDM 128 (for total incomer and outgoing breakers) . The display module should support to PC via RS 485 network or Ethernet Modbus. The rate should inclusive of necessary software for PC monitoring

Main Power Control Centre (MPCC)

630Amps 4P aluminium busbars:- All the neutral busbars shall have the same capacity of phase busbars. Necessary proper ventilation to be provided for heat disceptation

Note: All MCCBs shall have rotary handle mechanism and spreader wherever necessary.

Cable Entry/Exit: Suitable to top and bottom. (Rate as per quotation)

At EB Room

Supply, Erection, Testing and Commissioning of 200KVA Diesel Generator set with acoustic enclosure, comprising of Water cooled CPCB developing @ 1500 RPM and Alternator, complete with type approved canopy and all accessories. with the following technical specification: *Industries most reliable engines, proven over decades. *Low emission, High efficiency. *Compact, robust and rugged design. *Engine Dry type air cleaner *Exhaust Silencer (Residential type) Hospital Grade. *Expansion bellow *Lube oil cooler Lube oil filter (“Spin-on” type) *Fuel Filter (“Spin-on” type) *In line mono block fuel injection pump with Electronic Governor and fuel feed pump. *Dynamically balanced Flywheel with starter ring *Electronic Governor : Governing class G2 (as per ISO 8528 part V) *SAE 1 flywheel housing and flywheel suitable for SAE 14 disc coupling for close coupling of single bearing alternator. ( SR 2024-2025, Page no. 229,M-2351 )

outgoing of.100A,3Pole MCCB with Suitable contactor with 25KVAR Heavy duty capacitor - 2Nos.outgoing of.63A,3Pole MCCB with Suitable contactor with 20KVAR Heavy duty capacitor - 1No, 63A, 3Pole MCCB with Suitable contactor with 20KVAR Heavy duty capacitor - 1Nos,63A, 3Pole MCCB with Suitable contactor with 10KVAR Heavy duty capacitor - 1No, 40A, 3Pole MCCB with Suitable contactor with 5KVAR Heavy duty capacitor - 2No,40A, 3Pole MCCB with Suitable contactor with 2KVAR Heavy duty capacitor - 2No,40A, 3Pole MCCB with Suitable contactor with 1KVAR Heavy duty capacitor - 1No. Start, Stop, push buttons, internal wiring, colour coding, ferrules, cable gland plates, Aluminium earth bus for the entire length of the panel with bonding to earth and painting, Panel mounting MS Channels, fasteners, etc., including all associated control wiring and interlocking circuitry, MV panel sensing CT interconnecting wiring etc., complete.

LIFT Supplying, erecting, testing and commissioning of machine room less passenger Elevator having 13 passengers capacity, rated speed 1.0 mtr. / sec., for Basement, Ground , 1st floor and Second Floor 400 volt 3 phase, 50 Hz, AC variable voltage variable frequency derive with speed encoding, simplex full collective with / with out attendant, microprocessor based controller located top floor, variable frequency regenerative drive, flat polyurethane coated belts for traction media, stainless steel panels with hairline finish for car and door, gearless with permanent magnet motor located in the shaft top, all openings are located at the front of the hoist way, with centre opening Automatic with ACVVVF door operator with electronic door protective system, stainless steel hairline finish sliding doors, painted frame with down light false ceiling, Stainless Steel mirror finish hand rails, granite flooring of client choice, sixteen segment digital LED display position indicator in all floors, digital car position indicator, over load warning indicator, battery operated alarm bell and emergency light, fireman's switch at main lobby, with automatic rescue device, intercom between lift car and lobby and controller, voice synthesizer, 60 minutes fire rated car door. Car Entrance :- Clear opening

FIRE PUMP PANEL Supplying, installation, testing and commissioning of Fire Fighting Electrical Control Panel of cubical construction, floor mounted type fabricated using CRCA sheet, compartmentalised with hinged lockable door dust and vermin proof, cable alley, inter connection having switch gears and accessories mounting and internal wiring, earth terminals, numberings, necessary metering protections and indications complete in all respect suitable for operation on 415volt, 3 phase, 50 Hz AC supply with enclosure protection class IP 54 and mounted with the followings. (i). Incomer a. 1 No. 160A 4P MCCB Outgoings : 40A 4P MCB with RYB Indicator

AC Panel -1 Supplying,erecting,connecting & commissioning FLOOR MOUNTED CUBICLE TYPE 14 SWG thick CRCA sheet compartmentalised modular type with powder coated SUB POWER PANEL.The Board shall be incorporated with the following:-INCOMER: 200 AMPS TPN MCCB With 25KA(Ics) Withstanding Capacity With adjustable Over load and Short circuit releases.OUTGOINGS : 160 AMPS FP MCCB with 16KA(Ics) Withstanding Capacity With both fixed Over load and Short circuit releases. … 9 Nos.40 AMPS 4P MCB with 16KA(Ics) Withstanding Capacity With both fixed Over load and Short circuit releases. and Connected accessories etc.,

AC Panel -2 Supplying,erecting,connecting & commissioning WALL MOUNTED TYPE 14 SWG thick CRCA sheet compartmentalised modular type with powder coated SUB POWER PANEL.The Board shall be incorporated with the following:-INCOMER: 32 AMPS TPN MCB With 16KA(Ics) .OUTGOINGS : 20 AMPS DP MCB with 10KA(Ics) and Connected accessories etc.,

Pump panel -1 Supplying,erecting,connecting & commissioning WALL MOUNTED TYPE 14 SWG thick CRCA sheet compartmentalised modular type with powder coated SUB POWER PANEL.The Board shall be incorporated with the following:-INCOMER: 63 AMPS TPN MCB With 16KA(Ics) OUTGOINGS : 40 AMPS TPN MCB -3 Nos with 10KA(Ics) and Connected accessories etc.,

LIGHTING PANEL Supply and erection of 160 Amps capacity floor mounting / wall mounting panel board (Cubical type) with bus bar chamber made up of 14/16 SWG MS sheet for 3 phase 4 wire system with 25mm x 3mm tin coated copper flats for phases and neutral; cable chamber, switch chamber and with 2 Nos. 25mmx3mm tinned copper flat for the earth bus on the rear side of the panel board; necessary interconnections by copper flat of suitable sizes; suitable PVC colour sleeves for the interconnecting copper flats / rigid copper wire; earth connections to all swithces / bus bar by copper flats of suitable sizes from the earth bus; hylam sheet separation between bus bar and swithces; 1set LED pilot lamps with switches, fuse units, suitable angle iron frame size of 40mmx 40mmx 6mm with powder coated painting over one coat of red primer and with numbering; superscription of cables sizes, capacity of switches etc and incorporating the following:Incoming: 1 no.100A TPN 15KA MCCB with all protective devices.Bus capcity 3phase 4wire 100 A Aluminium bus Outgoings: 5 No. 63A TPN 16KA MCCB, 1 No. 25A DP MCB with all protective devices.

VERTICAL THREE PHASE MCB DISTRIBUTION BOARD WITH MCB : Supply and fixing of 12 way vertical TPMCB sheet steel Industrial Type TPMCB DB with IP54 Protection of surface type fitted with bus bars and neutral links with1 No. of 100A FP MCB as Incoming and 12 Nos.of 32A,10KA Triple Pole MCB in Flush with wall and making good of the concealed portion with earth connection.( Industrial Type TPMCB DB with IP54 Protections)

VERTICAL THREE PHASE MCB DISTRIBUTION BOARD WITH MCB : Supply and fixing of 12 way vertical TPMCB sheet steel Industrial Type TPMCB DB with IP54 Protection of surface type fitted with bus bars and neutral links with1 No. of 100A FP MCB as Incoming and 12 Nos.of 32A,10KA Triple Pole MCB in Flush with wall and making good of the concealed portion with earth connection.( Industrial Type TPMCB DB with IP54 Protections)

Supply and fixing of 7 segment 6 way TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 6 ways in each segment) and seperate provision for MCB / Isolators ( totally 18 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only (for First,second and third floor DB)

Supply and fixing of 25A Flush type Wall Socket 25A DP MCB complete set for AC Plug in flush with wall with earth connection (For AC Plug) (SD 143)

Supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonry pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 48W LED Street light fitting with LED (Higher end) with 1 metre 32mm dia. GI pipe (class B) Complete with suitable MS clamps for LED street light fitting and SMC box with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour

Supply, installation, testing and commissioning of 150W LED FLOOD LIGHT FITTING with cool day light suitable for wall / roof sheet mounting, made out CRCA powder coated body,IP65 aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, including electronic drivers, day light colour LED lamps, inter connecting wiring with suitable fixing clams, hooks as required including accessories all inclusive. (Provision)

Supply, Installation, Testing & Commissioning of 40W LED Gate Light Fitting. The Light Fitting should be powder coated with high pressure die-cast aluminium LED housing. And the LED fixed on die-cast aluminium heat sink for proper thermal management. and the operating voltage range 140 – 270V AC, provided with open and short circuit protection and input surge voltage protection. Decorative post top for 360 degree Indirect light with IP 65 protection, Resistant to impact and corrosion. Glare-free and better uniformity. MAPLE LPTO-40-CDL/M make :Crompton Features and details Aesthetically designed and soft illumination effectiveness : 2450 lm power : 40W colour : multi colour Included components : post Top Rate shall inclusive of necessary joint kit,glands,etc for loop in/out connection suitable to outdoor application. Crompton CAT REF : - LPTO-40-WW-M Equivalent.

supply and fixing of 24W LED 2x2 square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting. ( SD 439 )

Supply, installation, testing and commissioning of 18 W LED DOWN LIGHT FITTING with IP55 cool day light suitable for pole mounting, made out CRCA powder coated body, aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, including electronic drivers, day light colour LED lamps, inter connecting wiring with suitable fixing clams, hooks as required including accessories all inclusive.

Supply and Fixing of 40W 4' LED Tube Light with PVC unsheathed copper leads from terminals to the fitting. (Make : Philips/Crompton/Hiveless )

Supply and fixing of 9W LED and decorative Surface mounted LED luminarie Superior finish etc., complete. The rate inclusive of all taxes and transportation charges etc., complete

Supply and fixing of pressure die cast aluminium housing Bulk Head 10W LED fitting with IP65 protected with PVC unsheathed copper leads from terminals to the fitting.(Philips /Bajaj/ Crompton /K.Lite )

Supply and fixing of Floor mount LED Step Light for Outdoor 6W LED Light fitting ( BED Lamp)(IP67) fixture with PVC unsheathed copper leads from terminals to the fitting and to complete necessary accessories and etc to complete the work. model equivalent to Crompton LSL-6-CDL(Make:Philips/ Crompton/ Havells)

Supply, Installaion, Testing and Commissioning of Inspired from the deep roots of Bohemia, Monarc is an amalgation of classical Indian grandeur along with elegant Bohemian crystal design. The Monarc family of 12 Lamps Chandelier (12 x 4.5 W LED Filament Lamp) with accessories . Make Havelles, Klite(Rate as per quotation)

Supply and Fixing of Cove LED Light (10W) on floor or Ceiling with Mounting accessories ( IP20 & IP44 ) Complete etc,. (Make :Philips/ Klite /Crompton/Havelles )

Supply and installation of LED multi coloured serial lights concealed in a moulded housing of thicknes 2mm suitable for outdoor hanging.The serial lights shall be having Light Modes: Constant Bright, Flicker, Wavy, Fast and Slow Flash. The Led serial lights shall be internally connected and the connecting straps for a proper conjuction of the single profile. The rate is inclusive of the power cables, drivers, 12V SMPS, IR Controller with connecting wires with required taping, cartage & labour charges.

Supply and fixing of 1200mm (48") sweep AC ceiling fan complete with stepped electronic 300W regulator with 1metre down rod with fan clamp with side plates and cross arm of size 450mm (18") (Higher end) and wiring to the near by point with 1.5 sqmm FRLS , PVC insulated copper wires, including necessary accessories and hardware's as required. (SD -106)

Supply and fixing of 300mm(12")sweep (Heavy duty) AC Exhaust fan complete with necessary wall opening and making good of the wall and wiring to the near by point with 1.5 sqmm FRLS PVC insulated copper wires including necessary accessories and hardware's as required.

Supply and fixing of 300mm(12")sweep (Heavy duty) AC Exhaust fan complete with necessary wall opening and making good of the wall and wiring to the near by point with 1.5 sqmm FRLS PVC insulated copper wires including necessary accessories and hardware's as required.

Supply and fixing of 300mm(12")sweep (Heavy duty) AC Exhaust fan complete with necessary wall opening and making good of the wall and wiring to the near by point with 1.5 sqmm FRLS PVC insulated copper wires including necessary accessories and hardware's as required.

Supply and fixing of 1000W automatic electric water heater of 25 litres capacity suitable for 230V 50 c/s AC supply on suitable MS clamps with 3 core flex wire,but without plumbing work (SD-103)

Supply and laying of following XLPE armoured LTUG cable in a trench/Tray with suitable cable tie tag etc as required.

Supply and laying of 3 core 150 Sq.mm HT XLPE 11KV (E) Cable insulated, Armoured, HT cable on surface / cable trench using clamps in Trench / cable tray including all accessories, hardware etc., as directed.

Supply and laying of 31/2 core 150 Sq.mm PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and laying of 31/2 core 120 Sq.mm PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Clamping of 4 core x 25 Sq.mm PVC armoured LTUG Copper cable on post or on wall MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable

Supply and Clamping of 4 core x 6 Sq.mm PVC armoured LTUG Copper cable on post or on wall MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable.

Supply and Laying of 4C x 10 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and fixing of double compression brass cable gland for following Aluminium / Copper conductor XLPE insulated armoured cable of 1100 V grade with earth connection.

Supply and fixing of brass cable gland for 3 C x 300 Sq.mm PVC HT armoured cable with earth connection

Supply and fixing of brass cable gland for 3 1/2 C x 150Sq.mm PVC LTUG armoured cable with earth connection

Supply and fixing of brass cable gland for 3 1/2 C x 120 Sq.mm PVC LTUG armoured cable with earth connection

Supply and fixing of brass cable gland for 4C x 25 Sq.mm PVC LTUG armoured cable with earth connection

Supply and fixing of brass cable gland for 4C x 10 Sq.mm PVC LTUG armoured cable with earth connection.

Supply and fixing of brass cable gland for 4C x 6 sqmm COPPER cable LTUG cable with earth connection.

Supplying and Laying of 100 mm dia PVC pipe (6kg / sq.cm.)and relevant specials including packing the joints with rubbers lubricant with necessary connections to fittings etc., complete in all respects as directed by the departmental officers.

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) ( 4points / Coil)

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with Module GI switch box in flush with wall with 6A one way module switch with module front plate continuous earth wire connection by 1 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for PVC concealed light (6 points per coil) (for rooms like bath, toilet & pumproom, etc.).

Lift Shaft Wiring : Wiring, Connecting, Testing & Commissioning for lift well light point and 6Amps power socket outlet for all 4 floors with 2 x 2.5 sqmm FRLS PVC insulated stranded copper conductor of 1100V grade along with 1 x 2.5 sqmm FRLS PVC insulated stranded copper conductor cable as earth wire in MS conduit including providing and fixing switch box, 2 Nos. of 5A single way module switch (for controlling light point and socket Outlet ) for each floor of the lift well , with bulkhead lamp 1 No. 5A 5 Pin shuttered socket outlet with flush type switch for each floor of the lift well and making necessary connections complete etc. ( 6 points)

Wiring with 3R x1.5 sq.mm. (22/0.3) PVC insulated unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A two way module switch with module front plate with continuous earth wire connection of 1 run of 2.5 Sq.mm wire and making good of the concealed portion with suitable colour for Concealed PVC pipe Stair case Light point.

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 6A one way module switch and 1 no. 6A 3/2 pin module socket with module front plate with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with painting of suitable colour for concealed PVC pipe Plug point ( 8 points / Coil).

Wiring with 2 x 4 sq.mm. (56/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 16A one way module switch and 1 no. 16A 3/2 pin module socket with module front plate with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with painting of suitable colour for Concealed PVC pipe power Plug point ( 8 points / Coil)

Supply and Run of 2 of 4 sq.mm. (56/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour.

Supply and Run of 2 Run x 2.5 sqmm and 1R of 1.5sq sqmm PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable Pvc conduit pipe on concealed wall and ceiling with continuous earth wire connection with painting of suitable colour.

Supply and fixing of 1no.6A two module 5 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Scope cover wall cutting , grouting , flushing and making good on the wall.

Supply and fixing of 2nos.6A two module 5 pin socket , 2 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Scope cover wall cutting , grouting , flushing and making good on the wall.

Supply and fixing of manufacturer's GI metal back box and 3 nos of 6A modular switch, 3nos of 6A 3 pin combined modular type wall socket in flush with wall mounted on poly carbonate front plate with switch mounting metal parts, in flush with wall.

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Scope cover wall cutting , grouting , flushing and making good on the wall.

EARTH SYSTEM

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 50mm and 2 mtr long earth electrode of low carbon steel rod with 100 micron bonding and 25 kgs of carbon based environment friendly backfill compound and suitable clamp and with copper earth plate of size 125mm x 50mm x 6mm with necessary funnelling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry

Supply, Installation, Testing and Commissioning of earthing station consisting of 600 x 600 x 3 mm. thick, copper Plate earth electrode, back filling with alternate layer of charcoal, salt, brick masonry work for chamber 450 x 450 mm. heavy duty CI cover, watering pipe, funnel and earthing conductor as per IS:3043 specification. All civil works required such as excavation in all types of soils, rocks, PCC Earthing Chamber foundation, reinstatement and making good the surface to match original, removal of surplus earth etc. are included.

Coil earth to street light poles with No.8 SWG GI wire of 11.5 metres of length in which 10 metres of total length compressed in to a coil of one meter length (75mm to 100mm dia) connected suitable with hexagonal earth bolt of size 8mm in to 25mm welded on the pole at one end with a coil position fixed on the earth.

Supply, fabrication, of GI /Copper earth flat of following size in provided trench, clamping in wall, ceiling, with suitable Clamps/ saddles, connecting the joints through bracing / welding covering with termination in the earth pits, Panels, Distribution boards and equipment's with bitumen paint including accessories wooden plugs, screws, fastener etc., all inclusive

Supply and run of 25mm x 6mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection

Supply and run of 25mm x 6mm GI flat with necessary clamps / supports on wall / floor / ground for earth connection

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection

Supply and Run of 2 of 10 sq.mm. (140/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with painting of suitable colour.

LIGHTNING ROD : Air termination rod 16/ 10 mm( Lightning rod) - 4mtrs (PWD SR2024-25, pg no:242 , M-2563)

TEST LINK Supply of Test Link Box for each Down conductor in order to disconnect the earth termination system to enable measurement of resistance

Supply and installation maintenance free GI Earthing System comprising of 50mm dia and 2 mtr. long earth electrode of low carbon steel rod with 100 micron bonding and 25 kgs. of carbon based environment friendly backfill compound and suitable clamp

SURGE PROTECTION Supply and installation Cabinet Type Class 1 and 2 Combined Model SPD to arrest surges and overvoltages in the power line due to lightning switching action etc. they must be installed in the incoming MCC panel / DB of the respective building in parallel to the power circuit. Model: PSV4-12.5/400TT (3 phase power network)

FIRE ALARM

Supply, installation, testing and commissioning of Micro Processor based conventional 4 Zone Fire Alarm Control Panel having the rating of 24 volt DC power supply ,consisting 230/24 volt SMPS unit, 2Nos.of 12 volt 7 AH standby batteries, suitably mounted on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers.

Supply, installation, testing and commissioning of Conventional Smoke Detector suitably mounted on ceiling with MS juction box / false ceiling using fixing accessories like screws, plug, clamps, etc., as per standard methods and as directed by the Departmental Officers.(Make: Ravel / Equivalent)

Supply, installation, testing and commissioning of Electronic Hooter / Sounder providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers (Make: Ravel / Equivalent)

Supply and laying of FRLS PVC insulated 2 core 1.5 sq.mm. Armoured Copper Cable on ceiling / wall using fixing accessories like screws, plug, clamps, etc., asper standard methods and as directed by the Departmental Officers.

Telephone

Supply and fixing of telephone socket (telephone jack single line RJ 11) on suitable factory made metal box (necessed) with frame and face cover plate etc., complete required with connections

Supply and Clamping of armoured co-axial cable for TV (RG-06) in suitable PVC Pipe 1" thick on wall / ceiling with connected PVC accessories with clamps, saddles etc., complete.

Supply & fixing of TV socket (coaxial jack) on suitable factory made metal box (recessed) with frame and face cover plate etc., complete required with connections

CCTV SYSTEM

Supply, Installation, Testing and commissioning of 32 channel 8 SATA NVR, with 6T Hard Disk Drive 4 nos, New logical and visualized GUI design Dual-OS design to ensure high reliability of system running, ANR technology to enhance the storage reliability when the network is disconnected, Configurable normal or hot spare working mode to constitute an N+1 hot spare system Video Input and Transmission, Connectable to the third-party network cameras Compression and Recording, H.265+ compression effectively reduces the storage space by upto 75%, Full channel recording at up to 12MP resolution HD Video Output  HDMI1 / VGA1 outputs provided  HDMI1 Video output at up to 4K ( 3840 × 2160 ) resolution Storage and Playback, Upto 16 SATA interfaces and 1 eSATA interface for HDD connection, Support upto 10TB capacity for each HDD, Smart search for efficient playback. and smart playback to improve the playback efficiency, Supports VCA search for fire/ship/temperature/temperature difference detection triggered video files, POS information overlay on live view and playback, POS triggered recording and alarm Network & Ethernet Access  Hik-Connect for easy network management, 2 Gigabit Ethernet network interfaces. (Make : Hikvision / Dahua / Sony

Supply, Installation, Testing and commissioning of 16 channel NVR with 4TB HDD * 4nos, Up to 16-ch 8 MP IP cameras can be connected, Connectable to the third-party network cameras Compression and Recording, H.265+ compression effectively reduces the storage space by up to 75%, Full channel recording at up to 12MP resolution HD Video Output  HDMI1/VGA1 outputs provided  HDMI1 Video output ) resolution Storage and Playback, Up to 4SATA interfaces and 1 eSATA interface for HDD connection, Support upto 6TB capacity for each HDD, Smart search for efficient playback. (Make: Hikvision/Dahua/Panasonic) (Rate as per quotation)

Supply of 8MP, Internet Protocol fixed BULLET CAMERA with following specification: ●1/2.5" Progressive Scan CMOS, ● 3840 × 2160 @15 fps,2.8/4 mm fixed lens,01 lux @ (F1.2, AGC ON), 0.028 lux @(F2.0, AGC ON), 0 lux with IR, H.265+, H.265, H.264+, H.264, 2 Behaviour analyses ( Line crossing detection, intrusion detection) ● Face Detection ● 120dB WDR, ● BLC/3D DNR/ROI, IP67 complied ●On-board Storage - Built-in micro SD/SDHC/SDXC card slot, up to 128 GB, ● Shutter Speed 1/3 s to 1/100,000 s, ● 3-Axis Adjustment Pan: 0° to 360°, tilt: 0° to 100°, ● rotate: 0° to 360°, 2.8 mm, ● horizontal FOV: 102°, vertical FOV: 53°, diagonal FOV: 124°, ●Lens Mount M12 ● IR Range I5: up to 50 m, ● Image Settings Rotate mode, saturation, brightness, contrast, sharpness adjustable by client software or web browser, ● Power Consumption and Current-12 VDC, 0.7 A, max. 7.5W PoE: (802.3af, 36V to 57V), 0.3 A to 0.2 A, max. 9W ● Camera out fitted with metal housing so as to prevent the lens from damages during physical abuse. (Make: Dahua/Panasonic)

Supply ,Testing and Commissioning of Dom Camera 8MP IR camera (rate as per Quotation)

Supply, Installation, Testing and Commissioning of 55" smart LED TV with following specifications a) Full HD 1920 x1080 (4K monitor) b) IPS panel c) Slim back light LED module d) 900 PMI e) Triple XD engine f) Dynamic scanning g) ANR h) True colour generator i) 8modes of picture j) picture wizardIII k) Real cinema 24P l) HDMI -3nos m) USB -3nos n) Built in LAN o) Magic remote p) Dimension 1242 x 724 x 55.1min(37). (Make: Sony/ LG /Samsung).

Supply and fixing of outdoor 4X6 PVC box with 102mm x 77mm x 102mm with all fixing accessories.

Supply and Clamping of CAT 6 armoured cable in suitable PVC Pipe 1" thick on wall / ceiling with connected PVC accessories with clamps, saddles etc., complete. (Between ethernet switch to camera and radio modem) i. Application : Primary (Campus), Secondary (Riser), Tertiary(Horizontal) IEEE 802.3 : 10Base-T; 100Base-T; 1000Base-T IEEE 802.5 16 MB; ISDN; TPDDI; ATM ii. Standards: ISO/IEC 11801 2nd ed.; IEC 61156-5 2nd EN 50173-1; EN 50288-6-1,EIA/TIA 568C.2, RoHS Compliant. Fire Rating: PVC : IEC 60332-1. iii. Conductor - Bare Copper Wire iv. Insulation - Polyethylene v. Twisting - 2 Cores to the pair vi. Cable lay up - 4 Core to the pair It has diameter of (23 AWG) 0.550 ± 0.015.Insulation : Polyethylene.GI wire of size is 0.90 ± 0.030mm.

Fixing and Termination of CAT 6 Cable RJ 45Jack Single Point ( Point to Point ) Crimping, Testing and arrangement charges.

Supply and fixing of POE 24 port switch 10/ 100 / 1000 Base -T / 2 x 1000Base-FX / 20Gbps bandwidth / IEEE803.af/at compliant PoE+ / RJ45 supports auto MDI/MDI-X function / Auto negotiation speed, half/full-duplex / Store and forward / Max packet size: 10kbytes / Wide range power design (12~56VDC) / Operating temperature (-40 ̊C ~ +75 ̊C) / Reverse polarity protection / Resettable fuse to protect against overcurrent / IP-40 protection / EFT protection for power line.

Supply and fixing of POE 8 port switch 10/ 100 / 1000 Base -T / 2 x 1000Base-FX / 20Gbps bandwidth / IEEE803.af/at compliant PoE+ / RJ45 supports auto MDI/MDI-X function / Auto negotiation speed, half/full-duplex / Store and forward / Max packet size: 10kbytes / Wide range power design (12~56VDC) / Operating temperature (-40 ̊C ~ +75 ̊C) / Reverse polarity protection / Resettable fuse to protect against overcurrent / IP-40 protection / EFT protection for power line. (Make: DLINK,NETGEAR/ TPLINK)

Supply and fixing of Out Door Weather Proof Box 2Ft x 2Ft Out Door Weather Proof Box 2Ft x 2Ft

Supply and Fixing of Rack with Accessories -Higher end 42 U Rack with LNS unit and fan extra for the above rack.

Supply and fixing of 2 feet CCTV Camera Stand with attachment fittings as follows: * Weather heads and couplings * Cabinet mounting fittings, plates, brackets as needed. * Reinforced couplings for wire entrances to cabinets.

Supply and Installation for 2KVA UPS with Battery, Single Phase UPS (Single Phase In & Single Phase Out) Capacity - System with Battery - 2Hours back up

Supply and fixing of 6m Length pole with base plate of size 250x250x6mm as per IS-875 with following specification. Pole Outer die -76.10mm x 3.65mm Thick x 6 meter.

Supply and filling in foundation and basement with M sand / filling sand in layers of not more than 15cm thick well watered, rammed and consolidated etc., complete as per standard specification.

Providing and relaying Plain Cement Concrete 1:2:4 (One cement Two sand and ten broken Machine crushed stone jelly ) using HBG Machine crushed stone jelly of size 20mm gauge for founding and basement including de-watering if found necessary and laid in layers of not more than 15cms thick etc., complete complying with standard specification and as directed by the departmental officers.

PA SYSTEM

Supply and Installation of 15 watts indoor Wall Speaker with Line Matching Transformer in the existing pole with supporting clamp Model:- Specification:- 1.Input Power : 15W RMS/20W Max 3. Frequency : 250-10,000Hz 4. SPL : 108dB/1W/1m,122dB/25W/1m at 1kHz 5. Power Taps : 40/30/20/10/5W (Make: Ahuja, Bose, Yamaha or equivalent) (Make: Ahuja AMH402T/Bosch or its equivalent)

Supply, Installation, Testing & commissioning of 240 watts P.A Booster Amplifier with the output power of 1350 watts maximum, 500watt rms at 10% Thyristor harmonic distortion(THD), 850watt RMS at 5% THD, 800 watts RMS at 2% THD and the power supply AC voltage ranging from 220-240 volt, 50/60 hertz. with the DC input of 48 volt and 1000watts has tone controls of Bass=+- 10 db at 100 hz weighing 42kg with the speaker output of 2Q,4Q.70volt&100volt has power consumption of 1600VA AC &12A DC and 100db output regulation at 1khz no load to full load ratio. The signal to noise ratio is 60db with the input channels of 0.8mv/4.7kq,3*Aux 100mv/50kq.The frequency response of 50-15000hz+-3db.(Make: Ahuja SSA 10000 /Bosch or its equivalent)

Supply, Installation, Testing & Commissioning of 10" gooseneck with suitable base incorporates separate bush switches for momentary and dynamic microphone with 600ohm impedance and has 2.5mv/pa sensitivity and frequency response ranging from 50-15000hz with multi tone chime model.(Make:-ACM66 Ahuja/Bosch/its equivalent)

Supply and run of Armoured Speaker Cable 2 core 1.5 sqmm PVC insulated SC unsheathed of 1100V Grade in suitable PVC conduit pipe on concealed wall and ceiling with painting of suitable colour.

Supply & Installation of custom built M.S Powder coated wall mounting Audio rack with Lock & key for housing of Amplifier & player/Recorder conforms to EIA-310,IEC-60297 and able to withstand the load of 40kg with welded construction made up of CRCA steel with suitable height, width and depth.

Supply, Installation, Testing & Commissioning of Cordless mic UHF model.(Make:-ACM66 Ahuja/Bosch/its equivalent)

Preparation of CEIG drawings, Liasioning with CEIG for getting drawing approval, arranging inspection, getting safety certificate,Preparation& submission of AS BUILT drawings as per the site system installation. To Arrange Four Sets of paper print for As-built drawings & a soft copy of these drawings to be submitted to the client while the time of work completion at site.(All statutory fees to be paid in this regard will be reimbursed by the client against submission of paid receipt & the same cost should not be included in this item)

Supply, Installation, Testing and Commissioning of 75" Commercial monitor with following specifications a) Full HD 1920 x1080 (4K monitor) b) IPS panel c) Slim back light LED module d) 900 PMI e) Triple XD engine f) Dynamic scanning g) ANR h) True colour generator i) 8modes of picture j) picture wizardIII k) Real cinema 24P l) HDMI -3nos m) USB -3nos n) Built in LAN o) Magic remote p) Dimension 1242 x 724 x 55.1min(37). (Make: Sony/ LG /Samsung). (Rate as per quotation)

HIWALL - DX UNIT

Supply, Installation, Testing and Commissioning of Wall mounted Split type 1.5TR Air conditioning unit with supply and installation of necessary accessories including necessary length of copper pipes, suitable type double boost voltage stabilizer, pvc drain pipes, also includes necessary opening in the walls (if necessary)for the drain pipe routing and all other required accessories for the 1.5TR split type AC unit. (Make: (5star) -Blue Star,OG/Carrier/Voltas. or equivelent)

Supply and laying of 1/2" and 1/4" Copper Pipe (Extra Beyond 3 Mtrs Supplied with AC unit)

Supply and laying of 4C X 1.5 sqmm insulated multistrandad flexible copper copper cable for control wiring between indoor and outdoor unit

Supply and Installation of 1" PVC water Drain pipe line for Air conditioners.

Supply & Installation of 5KVA capacity Automatic Voltage Stabilizer with time delay relay (V guard/ Equivalent).

DUCTABLE AC - DX UNIT

Supply, Installation, Testing, Commissioning and handing over of 16.5 TR Ceiling Supsended ductable AC units.

Supply, Installation, Testing, Commissioning and handing over of 8.5TR Ceiling Supsended ductable AC units.

Supply & installation of hard drawn copper pipes 1.1/8 - 1/2 7/8-3/8 ,and Foam Cotton Roll per meter with 13mm thick nitrile rubber insulation (rate as per quotation)

Supply and laying of 7C X 1.5 sqmm insulated multistrandad flexible copper copper cable for control wiring between indoor and outdoor unit

Supply & installation of water line drain pipe 32mm (1inch) with 9mm thick nitrile rubber insulation with necessary supports and accessories (rate as per quotation)

Supply and fixing of Thread rod and Channel

Supply , installation and Testing of (N2)

Supply, fabrication and fixing of MS Channel for Mounting the Airconditioning Indoor Unit .

Supply, fabrication and fixing of MS Channel for Mounting the Airconditioning outdoor Unit .

Supply and Fixing of Scoffolding ( steel pipes ) Connected accessories such as swing, shackles, couplers, clamps, putlogs and ladder etc.,

Supply , Fabrication and erection of fabricated ducting made up of GI sheets of 24 Gauage Thickness.

Supply , Fabrication and erection of fabricated ducting made up of GI sheets of 22 Gauage Thickness.

Supply , Fabrication and erection of fabricated ducting made up of GI sheets of 20 Gauage Thickness.

Supply and providing thermal insulation of 9mm thick vidoflex with Aluminum Foil

Supply and fixing of acoustic insulation with 10mm thick open cell nitril rubber.

Supply and fixing of extruded aluminum power coated, Supply and return Air Grilles / Diffusers with Volume control Damper.

Supply Volume control Damper.

Supply and fixing of Flexible Canvas Connection .

Supply and Filling of R-410 Refrigerant Gas

Transportation, Loading, unloading, Lifting, shifting of Equipments and Materials. (Rate as per quotation)

FIRE FIGHTING ARRANGEMENT

Supply, installation of Fire Fighting Application 180 degree swinging type, hose reel drum with 20mm dia braided thermoplastic hose of 30 metres long, so as to extend to necessary distance by self rolling spindle wheel including necessary 20mm dia ball valve and open and close spray nozzle, warm clip, etc., as per the standard pattern of any reputed make at every floor nearer to hydrant valve, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary., etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, erection, testing and commissioning Mono Block type Fire Fighting Pressurisation Pump of 180 LPM 110 metres head at 10 HP with suitable base frame including necessary vibration bad mounting etc., including conveying, fixing and incidental charges., etc., complete as per standard specification and as directed by the Departmental Officers. (Make: Kirloskar / Equivalent)

Supply, erection, testing and commissioning of Fire Fighting 4 Way Fire Brigade Inlet with necessary gun metal 63mm dia non return spring shutter arrangements, so that to control one way flow at the time of emergency water supply by fire and rescue service fire engine entry including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KIARTAR / OMEX / EQUIVALENT.

Supply of Fire Fighting Application MS Hose Box to keep two number of hoses and 1 No. of branch pipe with nozzle having proper glass window type double door with universe open key, painted inside white and outside Post Office Red. Near every hydrant point including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply and kept in position of 9 litres capacity Fire Buckets of 4 Nos. with Bucket Stand as per standard specifications and as directed by the Departmental Officers

Supply, erection, testing and commissioning of following MS ‘C’ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm including necessary fittings like MS flange of table ‘E’, elbows, reducers, gaskets, bolt, nuts with washers & joints as per standard method of arc welding, including one coat metal primer and two coat Post Office Redpainting including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: JINDAL / EQUIVALENT.

150mm Dia

100mm Dia

Supply, erection, testing and commissioning of Cast iron body and Gun metal or stainless steel internal Non-return valve of following sizes to control one way flow of water to be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table ‘E’, gaskets, bolts & nuts, etc. as per IS 5312 including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers.

150mm Dia

100mm Dia

Supply, erection, testing and commissioning of Gun Metal Gate Valve of size 50mm dia size including necessary MS flange of table ‘E’, gaskets, bolts & nuts etc., installed at pump house delivery line for the purpose of priming water to suction line including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: LEADER / EQUIVALENT.

Providing, fixing pipe supports from columns / wall or suspenders from roof slab to suit various dia of pipes made out of GI / MS adjustable rods threaded for a sufficient length to adjust the height of support along with clamping arrangement for holding pipes of anchor fastening, arrangement design of hanger and should confirm with specification.

100mm Dia

Supply, erection, testing and commissioning of Air Release Valve of 20mm dia, so as to release airlock in 100mm dia MS pipe at top most wet riser, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KARTAR / EQUIVALENT.

Supply erection testing and commissioning of Electric Motor Driven Fire Pumpset suitable for automatic operation and consisting of following: a. 1 No. horizontal split casing centrifugal type fire pump capable of delivering 4550 LPM against a total head of 110 metres, so as to ensure a minimum pressure of 3.5 kg. per sq.cm at the farthest top most hydrant / outlet with pump casing of cast iron to grade FG 200, IS 210-1978 and parts like impeller, shaft sleeve, bearing ring etc., of non-corrosive metal either like bronze, brass or gun metal and shaft of stainless steel. b. 1 No. squirrel cage induction motor of 175 HP, 415 Volt, 3 phase 50Hz rating, conforming to IS:325-1978 with class "F" insulation, totally enclosed, IP 55 for enclosure fan cooled type conforming to relevant protection clause of IS 4691, synchronous speed of 2900 RPM. c. Common bed plate fabricated with MS channel / cast iron type for assembling the pump and motor flexible coupling between the pump and the motor with coupling guard for protection - 1 No. d. Making cement concrete foundation suitable for the above pumpset including vibration isolation pads as necessary, foundation bolts, brackets, clamp fixtures, grouting, etc., in accordance with the manufacturer's design and as per standard methods and including conveying, fixing and incidental charges, etc., complete as per standard Specification and as directed by the Departmental Officers.

Supply, installation, testing and commissioning of Diesel Engine Driven Main Fire Pump suitable for automatic operation and consisting of followings and complete in all respects as required. a. 1 No. horizontal split casing centrifugal type fire pump capable of delivering 4550 LPM against a total head of 110 metres, so as to ensure a minimum pressure of 3.5 kg. per sq.cm at the farthest top most hydrant / outlet with pump casing of cast iron to grade FG 200, IS 210-1978 and parts like impeller, shaft sleeve, bearing ring etc., of non-corrosive metal either like bronze, brass or gun metal and shaft of stainless steel. b. 190 BHP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant BS & IS standard complete. c. Auto starting mechanism, 12 volts / 24 volts electric starting equipment like self motor, dynamo, solenoid switches, etc. d. 110 litres capacity diesel tank mounted over stand fabricated using 25mm x 25mm x 6mm size MS angle providing with level indicator, inlet port, outlet port, drain port and diesel return line port and fuel pre-filter, after filter etc...............

e. Exhaust system having flexible metallic mufler, 100mm dia MS heavy pipe extended upto 1m outside pump house duly insulated with 50mm thick glass wool with 1mm thick aluminium sheet cladding, residential silencer with necessary MS support arrangements from wall or ceiling as per site condition. f. Dash board consisting the instruments like Temperature Gauge, Galvano Type DC Ammeter, Lubricant Oil Pressure Gauge, Ignition Switch, Emergency Stop and all other protection equipment as per specification, stop soleneid for auto stop in the event of fault with audio indications, painted with Post Office Red Colour, etc., as required. g. 12V / 24V, storage battery, maintenance free tape, 180AH rating, MS fabricated common base plate, coupling guard, foundation bolts, etc., as required. h. Postioning the diesel engine driven fire pump over cement concrete foundation using suitable size antivibration mounting arrangement. All works including conveying, fixing and incidental charges, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KIRLOSKAR / EQUIVALENT.

Supplying, erection, testing and commissioning of Diesel Engine Pump Main Control Panel & Jockey Pump including necessary auto cut-in, cut-off and manual operations, battery charger switch arrangements, voltmeter, ammeter and running indication siren provision, wall mounting type, etc., as per the standard method and as directed by the Departmental Officers.

FIRE SAFETY

First Aid Box complete with all First Aid Medicines

Shock Treatment Chart fixed in glass frame

Fire Extinguisher Co2, 4.5 kg. confirming to TAC Norms

Danger Board as required by the Electrical Authorities

2m x 1m Rubber Mat suitable for 11 KV installation confirming to IS (5 set)

Hand Gloves 11KV Grade

Earth Discharge Rod

Supply and kept in position of 9 litres capacity Fire Buckets of 4 Nos. with Bucket Stand as per standard specifications and as directed by the Departmental Officers

Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc, complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT

Supply and fixing of Carbon-di-Oxide Gas Type 2 kg. capacity Fire Extinguisher as per New IS15683, complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc., complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT /SAFETY FIRST / EQUIVALENT

KSR ASSOCIATES (BID ID -1216093)

Shree Shivane Construction (BID ID -1216884)