GE/T-01/2025-26 PROVN OF CERTAIN REVENUE AND MINOR WORKS AT AHRR UNDER GE E/M RR HOSPITAL DELHI CANTT-10.

Amount

M&L for brick work with sub-class `B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4, complete all as specified and directed by Engr-in-Charge.

Taking down cement plaster of any description on brick or stone walls, etc including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed by Engr-in-Charge.

M&L for 15mm thick rendering on brick or concrete wall surfaces in cement mortar 1:6, finished the surface even and fair without using extra cemnent, complete all as specified and directed by Engr-in-Charge.

M&L for 15mm thick rendering on brick or concrete wall surfaces in cement mortar 1:4, finished the surface even and fair without using extra cemnent, complete all as specified and directed by Engr-in-Charge.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over 1 to 2mm thick cement base wall care putty, complete all as specified and directed by Engr-in-Charge.

M&L for preparation of newly plastered surfaces of walls and applying two coats of exterior grade weather proof paint over a coat of primer, complete all as specified and directed by Engr-in-Charge.

M&L for complete removal of existing treatment from internal surfaces of walls by electrically operated grinder, washing and filling of holes with filler material and applying 1-2mm thick cement base wall care putty on the whole surface to achieve smooth, even & uniform surface including grinding with sand paper and levelling of surface and applying two coats of oil bound distemper over one coat of primer, complete all as specified and directed by Engr-in-Charge. Note: (a) All works shall be done mechanically through authorised applicator only. (b) Authorised applicator of paint manufacture shall have valid authrisation letter from the manufacturer (minimum regional HQs) issued not earlier than 30 days from start date of the said finishing work. (c) The contractor shall provide application for testing and certification of finishes by paint manufacturing firm/ their authorised applicator. (d) Cost of all above aspects shall be deemed to be included in quoted rate of the contractor.

M&L for complete removal of existing treatment from internal surfaces of ceiling by electrically operated grinder, washing and filling of holes with filler material and applying 1-2mm thick cement base wall care putty on the whole surface to achieve smooth, even & uniform surface including grinding with sand paper and levelling of surface and applying two coats of oil bound distemper over one coat of primer, complete all as specified and directed by Engr-in-Charge. Note: (a) All works shall be done mechanically through authorised applicator only. (b) Authorised applicator of paint manufacture shall have valid authrisation letter from the manufacturer (minimum regional HQs) issued not earlier than 30 days from start date of the said finishing work. (c) The contractor shall provide application for testing and certification of finishes by paint manufacturing firm/ their authorised applicator. (d) Cost of all above aspects shall be deemed to be included in quoted rate of the contractor.

M&L for complete removal of existing treatment from from external surfaces of walls by electrically operated grinder, washing and filling of holes with filler material and applying 1-2mm thick cement base wall care putty on the whole surface to achieve smooth, even & uniform surface including grinding with sand paper and levelling of surface and applying two coats of exterior grade weather proof paint over one coat of primer, complete all as specified and directed by Engr-in-Charge. Note: (a) All works shall be done mechanically through authorised applicator only. (b) Authorised applicator of paint manufacture shall have valid authrisation letter from the manufacturer (minimum regional HQs) issued not earlier than 30 days from start date of the said finishing work. (c) The contractor shall provide application for testing and certification of finishes by paint manufacturing firm/ their authorised applicator. (d) Cost of all above aspects shall be deemed to be included in quoted rate of the contractor

Dismantling floor, hearth or wall tiling including cement mortar bedding (including backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed by Engr-in-Charge.

M&L 10 mm thick screed bed or bedding layer in cement mortar (1:4) to receive wall tiles, complete all as specified and directed by Engr-in-Charge.

M&L for coloured glazed ceramic wall tiles as in vertical surfaces of size 450 mm x 300 mm x 7 to 8 mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match, complete all as specified and directed by Engr-in-Charge.

M&L for exterior finish wall tiles as in vertical surfaces of size 300mm x 450mm x 10 mm / 300mm x 600mm x 10mm thick, including 10mm thick rendering in CM 1:4 to recieve wall tiles, design and pattern as directed, set and jointed in neat cement slurry and pointed in white or colour cement to match, complete all as specified and directed by Engr-in-Charge.

M&L for 18-20 mm thick machine cut kota stone slab flooring laid over and including 20 mm thick screed bed or bedding layer in CM 1:6, jointed with grey cement slurry mixed with pigment to match the shade of slab including grinding, rubbing and polishing, complete all as specified and directed by Engr-in-Charge.

M&L machine cut kota stone slab flooring 18-20mm thick riser of steps with single piece. skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including 10mm thick rendering in CM 1:4 as a backing coat on walls for fixing of tiles, complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engr-in-Charge.

M&L for RCC type B1 1:2:4 (using 20mm graded crushed stone aggregate) as in slab supported on walls, beam and columns in floors, roofs, landing, balconies , canopies, deck slabs and in shelves and the like complete all as specified and directed by Engr-in-Charge.

Form work to soffits of suspended slab such as roof slab, floor slab, landing and similar workn exc 200mm thick flat rough finished surfaces, complete all as specified and directed by Engr-in-Charge.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide with rough finished surfaces, complete all as specified and directed by Engr-in-Charge.

M&L for steel TMT bars 10 mm dia and over, cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binging with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed by Engr-in-Charge.

Taking down chowkats or frames including shutter (without taking off shutters from the frame) area n exc 1.50 Sqm each, complete all as specified and directed by Engr-in-Charge.

Taking down chowkats or frames including shutter (without taking off shutters from the frame) area exc 1.50 Sqm but n.exc 4.00 sqm each, complete all as specified and directed by Engr-in-Charge.

S&F pressed steel frames made out of mild steel 1.25mm thick sheet, with with size of frame 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., and applying a shop coat of red oxide primer including prividing PCC 1:3:6 type C-0 (using 12.5mm graded crushed stone aggregates) for filling back of chowkhats, complete all as specified and directed by Engr-in-Charge.

S&F 35mm thick flush shutters, solid core construction, with block board core and plywood face panels commercial type with both faces, complete all as specified and directed by Engr-in-Charge.

M&L for prepration of new wooden surface of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthatic enamel paint over a coat of pink primer, complete all as specified and directed by Engr-in-Charge.

S&F 150 mm long, aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed by Engr-in-Charge.

S&F aluminium anodised barrel tower bolt 200mm long extruded section all complete all as specified and directed by Engr-in-Charge

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodised, complete all as specified and directed by Engr-in-Charge.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet,cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium complete all as specified and directed by Engr-in-Charge.

S&F 140mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, complete all as specified and directed by Engr-in-Charge.

Supplying, fabricating & fixing aluminium powder coated (minimum thickness of powder coating 50 micron) glazed three track sliding window of frame 100x44x1.5mm and sliding shutter of section 40mmx19mm including 3mm thick sheet glass, ordinary quality exceeding 0.36 sqm in each pane, in two track shutter and in one track stainless steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, all fitting such as aluminium handle of size 100mm and locking arrangement with each moving leaf, complete all as specified and directed by Engr-in-Charge.

M&L for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165, complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new steel surfaces of any description not other wise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed by Engr-in-Charge.

M & L for glazed ceramic digital coloured tiles 600x300x7 to 8 mm thick in dado/skirting set and jointed in neat cement slurry and pointed in coloured cement to match over 10mm thick rendering in CM 1:4 complete all as specified and directed by Engr-in-Charge.

M & L Non skid coloured ceramic tiles 7-8 mm thick (square or rectangular) area of each tiles exc 0.06 sqm but n exc 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match over 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engr-in-Charge.

M&L for Virified Ceramic tiles light shade 8-9 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid incl over 15mm thick cement screed bed in CM 1:6 complete all as specified and directed by Engr-in-Charge.

All as per ser items No. 35.00 here-in-before but in dado/skirting over 8-9mm thick rendering in CM 1:4 as backing coat complete all as specified and directed by Engr-in-Charge.

M & L for 16-18mm thick granite of any type (table rubbed & polished) in jambs, pillars, window cills, plate forms in CM (1:4) including pointing in white cement (1:2) ,using marble dust with admixture of pigment to match with shade of granite over 20mm thick screed bed in in CM 1:6 complete all as specified and directed by Engr-in-Charge.

S&F of aluminium powder coated chowkhats of 100x44x1.5mm section with rebate complete frame complete all as specified and directed by Engr-in-Charge.

Supply, fabricating and fixing of aluminium door shutter powder coated of extrusion aluminium section, Vertical style of door shutter of size 85mmx44.45mmx1.5mm thick. Top, middle and bottom rail of size 85mmx44.45x1.5mm thick and fixing plain/tinted sheet glass or ACP sheet with aluminium beading and rubber gasket/beading as directed One mortice lock for aluminium door (each), and three nos aluminium hinges of size 100mm of and two aluminium tower bolts of 250mm size of each door fixed with rawl plug including rectification of floor/wall to match the existing surfaces all as specified and as directed by Engineer-in-Charge at site. (Cost of sheet glass Plain/frosted/ACP Sheet shall be measured and paid seprately )

M&L for 5.5 mm thick plain glass fixed with beading in aluminium frame complete all as specified and as directed by Engr-in-Charge.

Dismantling Asbestos cement (corrugated, semi-corrugated etc.) sheets in roof covering.complete all as specified and directed by Engr-in-Charge

S&F prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge.

S&F PVC 18/19mm thick PVC moulded solid board ,one side prelaminated for cabinets boxes shutters,etc with shelf and shutters full size fitted under/above kitchen cooking platform and other platform complete all as direction of the Engr-in charge and the manufacturer complete all as specified and directed by Engr-in-Charge

S&F soft closing clip on hinge, full / half overlay type, of stainless steel,complete all as specified and directed by Engr-in-Charge

S&F 100 mm size stainless steel handles, matt finish, complete all as specified and directed by Engr-in-Charge.

S&F brass two levers keys,Locks, cupboard,grade I, size 50mm suitable for cup board door/drawer , complete all as specified and directed by Engr-in-Charge

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., complete all as specified and directed by Engr-in-Charge

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC (SWR) bend 110 mm dia fixed in position complete all as specified and directed by Engr-in-Charge.

S & F in repair stainless steel curtain rod 20-22mm dia of make VISTA or eqv. including brackets, side knobs fixed to wall complete all as specified and directed by Engr-in-Charge.

Demolition of brick work built in cement mortar including all quoins, arches, pillars, drain and culvert in foul condition etc.complete all as specified and directed by Engr-in-Charge.

M&L for brick work with sub class B bricks, straight or curved on plan exc 6 m mean radius built in CM 1:6 complete all as specified and directed by Engr-in-Charge.

Material & Labour for preparation of newly plastered external wall surface and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.with a coat of 1.5mm thick putty, complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete unreinforced( in ground floors and paving at any position 15 cm thickness (below or above ground level) complete all as specified and directed by Engr-in-Charge.

M&L for PCC 1:5:10 type E-2 (using 40 mm graded stone aggregate) in sunken floor complete all as specified and directed by Engr-in-Charge.

M&L for rendering 15 mm thick in CM 1:4 on brick or concrete surfaces using integral water proofing compound (3% by weight) for floor and sides of wall complete all as specified and directed by Engr-in-Charge.

M&L for 25 mm thick PCC 1:2:4 type B0 (Using 12.5mm graded stone aggregate) as in flooring complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair aluminium composite panels cladding of approved make & shade having total thickness of 4 mm (Top coil -0.5mm , non Toxic PE - Core - 3 mm and back Coil -0.50 mm ) with 25 micron PVdF Coating on top coil and polyester / epoxy coating on back coil ( 4-7 microns ) on aluminium substructure fixed with 19 mm x 12 mm x 1.6 mm aluminium cleat & 10 x 100 mm SS Wooden screw with PVC plug on faced horizontal/ vertical surfaces of rectangular / circular columns ,suspended ceiling Cills , jambs ,canopy with including necessary aluminium frame ,scaffolding etc. and making 10 mm to 20 mm wide grooves and applying non staining and non sticking waterproofing silicon sealant of and backing rods complete all as specified and directed by Engr-in-Charge. Note :- (i) Only exposed surface shall be measured and paid for. (ii) ACP Material shall be for exterior application & shade as approved by Garrison Engineer

S&F and fabrication Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161 1979 grade St.-240 complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new or previously untreated steel surfaces of any description, over 10cm in width or girth,not otherwise described, applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed by Engr-in-Charge.

Dismantling of wall and ceiling boards of any description, any thicknes including cover fillets and frame work complete all as specified and directed by Engr-in-Charge

M&L for forming jambs, etc. to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, in CM 1:4 complete all as specified and directed by Engr-in-Charge

M & L for 20mm thick granite of any type (table rubbed & polished) in jambs, pillars, window cills, plate forms in CM (1:4) including pointing in white cement (1:2) ,using marble dust with admixture of pigment to match with shade of granite over 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engr-in-Charge.

S & F solid PVC wall panelling consisting of 5mm thick wood grain finish PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed by Engr-in-Charge.

S & F for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed by Engr-in-Charge.

S & F solid PVC leeping of 2mm thick wood grain finish PVC sheet is heat bent as lipping on the edges of doors, windows & other edges inclusive of solvent cement and fixing at site complete all as specified and directed by Engr-in-Charge.

M&L for exposed GI frame/grid system duly powder coated for module size of 600 x 600 mm suitable for lay-in metal / mineral fibre ceiling tiles, having main T runner of 24 mm size, suspended at 1200mm C/C and cross T runner of 24 mm size, suspended at 600mm C/C with interlocking arrangements to form grid of 600 x 600mm, perimeter runner/channel of 15 mm size, main and cross T runner supported by 4mm dia GI rod from slab / Roof, wall angle etc with and including all fixing accessories and making good of distrubed wall surfaces with POP and one coat of oil emulsion distemper, as required to match the existing surfaces, complete all as specified and directed by Engr-in-Charge.

M&L for metal false ceiling, lay-in type, 0.7 mm thick, having tegular edge profile, duly powder coated, perforated type with glass fibre acoustic fleece, suitable for false ceiling grid/frame module of 600 x 600mm size, complete all as specified and directed by Engr-in-Charge. (Note : The grid /frame shall be measured and paid for separetly.)

S&F 5mm thick aluminium composite panel (ACP Sheet) including necessary clips, rubber packing & aluminium beading (aluminium frame) complete all as specified and directed by Engr-in-Charge.

M & L for glazed ceramic digital coloured tiles 300x450x8 to 9 mm thick in dado/skirting set and jointed in neat cement slurry and pointed in coloured cement to match over 10mm thick rendering in CM 1:4 complete all as specified and directed by Engr-in-Charge.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 20mm thick screed bed in CM 1:6 complete all as specified and directed by Engr-in-Charge.

M&L for Virified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles n.exc. 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid incl over 15mm thick cement screed bed in CM 1:6 complete all as specified and directed by Engr-in-Charge.

Supplying and laying of 20mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed by Engr-in-Charge.

Supplying and laying of 25mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed by Engr-in-Charge.

S&F 100mm bore cast iron soil waste and vent pipe (sand cast pipes) in any length with or without ears fixed with cement joints laid in floors or in trenches complete all as specified and directed by Engr-in-Charge.

S&F 75mm bore cast iron soil waste and vent pipe (sand cast pipes) in any length with or without ears with cement joints laid in floors complete all as specified and directed by Engr-in-Charge

S&F white colour, vitreous china washdown water closet pan (pedestal pattern) fancy type (excluding fixing bolts, flushing cistern and flush pipe), complete all as specified and directed by Engr-in-Charge.

S&F Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging devicewhite colour, all as specified and directed by Engr-in-Charge..

S&F vitreous china wash basin, white colour, flat back type, of approx size 580 x 450 mm (for hospital use) including waste coupling, wall bracket, waste pipe of suitable size etc,complete all as specified and directed by Engr-in-Charge

S&F wash basin mixer, with out pop up waste system, long body, made of cast copper alloy, chromium plated fancy type, suitable for 15 mm bore pipe, complete all as specified and directed by Engr-in-Charge

S&F PVC made multipurpose cabinet with front door looking mirror of overall minimum size 350 x 450 mm, complete all as specified and directed by Engr-in-Charge.

S&F chromium plated towel rail 20mm dia and 600 mm long complete all as specified and directed by Engr-in-Charge.

S&F of long body bib cock, 15 mm bore with wall flange made of cast copper alloy, chromium plated, complete all as specified and directed by Engr-in-Charge.

S&F angular stop cock/ angle valve 15 mm bore with wall flange made of cast copper alloy, chromium plated fancy type, complete all as specified and directed by Engr-in-Charge.

S&F handshower (health faucet) with 8 mm dia, 1.0 M long flexible tube, wall hook and wall flange made of cast copper alloy, chromium plated fancy type, complete all as specified and directed by Engr-in-Charge.

S&F 15mm dia PVC connection 45 cm long, complete all as specified and directed by Engr-in-Charge.

S&F two way bib cock suitable for 15 mm bore water pipe, with & including wall flange, made of cast copper alloy, chromium plated fancy type, complete all as specified and directed by Engr-in-Charge.

S&F SS glossy finish grating of square shape, overall size of 150x150mm with hinge type openable jali of 100 mm dia size with and including fixing with cement mortar to floor/nahani traps etc, complete all as specified and directed by Engr-in-Charge.

S&F 8-9 liters PVC valve less syphonic action type flushing cistern, low level white with inlet, ball valve, float and handle including bracket and flush pipe to squatt pattern closet including all joints and making good to the floor.complete all as specified and directed by Engr-in-Charge.

S&F toilet paper holder chromium plated complete all as specified and directed by Engr-in-Charge.

S&F bottle trap 32 mm size with 250 mm long wall connection pipe and wall flange made of cast copper alloy, chromium plated fancy type, complete all as specified and directed by Engr-in-Charge.

S&F Soap dish, chromium plated, approximat size 160X160X90mm fixed in repairs complete all as specified and directed by Engr-in-Charge.

M & L cast iron floor trap of 75 mm outlet plainincluding jointing to waste pipe in run lead fixed in cement mortar complete all as specified and directed by Engr-in-Charge.

M&L for preparing newly plastered wall surfaces and applying putty 1.5mm thick over cement primer followed by 2 coats of distemper oil emulsion complete all as specified and directed by Engr-in-Charge.

Taking down carefully unserviceable of aluminium point wiring complete except for ceiling or where not feasible fan/plug/bell but including fittings such as switches, ceiling rose, pendants, regulator etc. and making good disturbed surface to match with the existing surface of roof/ wall/ floor by applying putty and applying colour/ white wash finish complete all as specified and directed by Emgr-in-Charge.

M & L for point wiring concealed type with 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable connected to common earth and earth dolly with suitable copper lugs drawing into and including rigid non-metallic PVC surface conduit of 20mm dia or higher, medium grade complete with all PVC conduit accessories, GI metal flush box of 1.60 mm thick suitable for modular / conventional switches / sockets / fan regulators with cover plates, blanking plates, brass screws, cup washers etc including all cutting / chases etc in walls and making good to the disturbed surfaces to match the existing for One light/fan/bell/exhaust fan point controlled by one switch complete all as specified and directed by Engr-in-Charge. Note - All accessories likes modular top cover plate/ hylum sheet cover plate, Metal flush box, screws etc as applicable will be included in quoted rates.

All as per ser items No. 98.00 here-in-before but point wiring for one socket outet point 3 pin 5 amps on the independent board complete all as specified and directed by Engr-in-Charge.

All as per ser items No. 98.00 here-in-before but point wiring for one socket outet point 3 pin 5 amps on the same board complete all as specified and directed by Engr-in-Charge.

All as per ser items No. 98.00 here-in-before butwith 2.5 sq mm FRLS copper wire with 2.5 Sqmm FRLS copper earth wire for 3/5 pin 15 Amp power point on Independent board complete all as specified and directed by Engr-in-Charge.

S & F Modular Switch 1 way 16 A, 1 Module complete all as specified and directed by Engr-in-Charge.

S & F Modular Socket 6 / 16 A - 2/3 Pin combined 2 module complete all as specified and directed by Engr-in-Charge.

S & F Modular Switch 1 way 6 /10 A, 1 Module complete all as specified and directed by Engr-in-Charge.

S & F Modular Socket 6 / 10 A - 2 / 3 Pin combined 2 module complete all as specified and directed by Engr-in-Charge.

S & F Modular fan regulator step type, 120W 2 Module complete all as specified and directed by Engr-in-Charge.

S & F of Ceiling rose surface Polycarbonate type with three terminals 240 Volts complete all as specified and directed by Engr-in-Charge.

S & F in replacement of LED tube light fitting 20 watt (CW), 4 feet long in extruded aluminium batten with high efficient LEDs available in milky diffuser and Colour Rendering Index (CRI>70), IP20, correlated Colour Temperature (CCT- 5700K to 6500K), PF>0.9 and Voltage rated 220V to 240V complete all as specified and directed by Engr-in-Charge.

Taking down unserviceable sub main wiring of aluminium any type with earth wire and making good disturbed surfaces of wall/ floor or roof etc and applying putty, complete all as specified and directed by Engr-in-Charge.

Material and labour for Sub main wiring with 2 run of 4 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, drawn in and including PVC conduit with wall thickness 1.6mm thick and including 4 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire, connected with thimble from main DB / Panel to sub DB complete all as specified and directed by Engr-in-Charge. Note : 1. The two run of 4 Sqmm wire, one run of 4 Sqmm wire and 1 mtr PVC conduit pipe will be measured as one unit. 2. Cutting chases required for sub main wiring shall be finished with cement mortar 1:4 and surface shall be matched with existing shade of surface shall be deemed to be included in the unit rate quoted by the contractor.

S & F in replacement MCB, SP, 6 to 32 Amps capacity, 240V, B Curve type, 10kA, single pole with over load and short circuit protection complete all as specified and directed by Engr-in-Charge.

S & F in replacement MCB, SP, 40 to 63 Amps capacity, 240V, B Curve type, 10kA, single pole with over load and short circuit protection complete all as specified and directed by Engr-in-Charge.

S & F in replacement MCCB, 415 Volt, 16kA, 4 pole, 125 Amp capacity with over load and short circuit protection complete all as specified and directed by Engr-in-Charge.

S & F in replacement Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, surface mounting, VTPN 8 way, 415 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCCBs / MCBs and isolators etc and making all necessary connections complete all as specified and directed by Engr-in-Charge.

Taking down carefully ceiling / exhaust fan of any size, sealing cable end, dismantling blades & removing fan and blades to store, complete all as specified and directed by Engr-in-Charge.

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed by Engr-in-Charge.

M & L Earthing complete with galvanised steel earth plate electrode 600 x 600 x 6.3 mm thick buried directly in ground earth pit not less than 2.25 mtr deep below ground level connected with earthing lead of 4mm dia galvanised iron or steel wire all by means of nuts and bolt check nuts and washers of galvanised iron sheet all as shown in electrical plate Nos 5 of SSR Part - I and connected to and including earthing test point complete including testing filling of adequate quantity of charcoal dust and common salt including refilling earth and removal of surplus soil up to 50 mtrs PCC 1:3:6 type CI chamber precast RCC cover 40 mm thick reinforced with 6 mm dia MS bar 3 Nos both way with handle made but at 6 mm dia MS bar water pipe with wire mesh and connecting testing etccomplete all as specified and directed by Engr-in-Charge.

Commercial Traders (BID ID -3300035)