ADDN/ALTN TO BLDG NO P-01 TO P-08 AND P-15, BLDG NO P-18 TO P-22, BLDG NO P-70, P-71, P-72 AND P-73 OTM, BLDG NO P-42 (OFFICE COMPLEX), P-47 (CC) AND P-60 (QG) AT 1 ARMY HQ SIG REGT, DELHI CANTT

Amount

Demolition of cement concrete (reinforced) of any position not otherwise specifically provided for and including reinforcement required to facilitate demolition upto and including fourth story and on the roof top/mumty/parapet and removal of debris and rubbish out side MoD land complete all as specified and directed.

Demolition of brick work built in cement mortar in any description and position complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in Ground floors and paving n.exe 15cm thickness ( below or above ground level ) including removal of rubbish out side complex (MOD land), complete all as specified and directed.

Dismantling of PVC water tanks of exc 250 litres and n.exc 500 litres capacity of any condition or type complete all as specified and directed.

Dismantling of Cast Iron pipe/ RCC drain pipe/PVC pipe up to 100 mm bore complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortor bedding (but not backing) laid bedded and pointed in any mortar and removal of old tiles from premises complete all as specified and directed.

M&L for cutting chases on brick or concrete surface for concealed water tubing or girth n.exc 10cm including making good of disturved surfaces with PCC 1:2:4 type B0 using 12.5 mm graded aggregate complete all as specified and directed.

Dismantling of Brick tiles or terracing tiles, single layer on roofs, kerbs, aprons, etc. (each layer) complete all as specified and directed.(Note : All roots of plant on either on wall or roof to be removed and making good the disturbed surfaces. The rate quoted be the contractor is deemed to be included in the unit rates.)

Demolition of Mud phuska in roofs, any thickness including plastering and leeping of any thikness upto 30cm deep complete all as specified and directed.(Note : All roots of plant on either on wall or roof to be removed and making good the disturbed surfaces. The rate quoted be the contractor is deemed to be included in the unit rates including the removal of mud phuska outside defence land.)

M&L for the following:- (a) Dismantling of floor of WC with Indian type Water closet and removing out the cinder/concrete from sunken protion, cleaning of RCC surface to remove dust, loose particle with compressed air or any other suitable method depending on site conditons, grinding any sharp edges etc complete all as specified and directed. (b) Cleaning or RCC surface to remove dust, loose particle etc with compressed air or any other particles or any other suitable techniques on site conditions etc. (c) M&L for a glass fibre reinforced acrylic modified cementitious coating system with base coat @ 1.50 Kg/Sqm, glass fibre reinforcement and top coat with acrylic modified cementitious coating system @ 1.50 Kg/Sqm (d) M&L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound. (e) M&L for providing 25mm dia GI pipe spout projecting at least 150mm beyond outer face of wall. (f) M&L for sunken portion filled with 40 mm graded brick bats and finished with 50 mm thick PCC 1:2:4 type B1 all as specified and directed. (g) The area of Each WC portion is n.exc 2.00 Sqm each. (h) Cost of the above aspect shall be deemed to be included in the quoted rates of the respective item and nothing extra shall be paid on this account. Note : The work will be executed by authorised manufacturers/applicator.

Taking up or down 15 mm bore GI tubing and connections including cleaning for re-fixing complete all as specified and directed.

All as per item No. 11 above but 20 mm bore

Taking down chowkats or frames exc. 1.5 Sqm and n.exc 4 Sqm each with shutters (without taking off shutters from frames) complete all as specified and directed.

Taking down chowkats or frames not exc. 1.5 Sqm each with shutters (without taking off shutters from frames) complete all as specified and directed.

Taking down shutters of any description exc 1 sqm and not exc 2 sqm each complete all as specified and directed.

Taking shutters of any description exc 1 sqm and not exc 2 sqm each and refixing in the same or other opening as required at site complete all as specified and directed. Note : The rate quoted by the contractor are inclusive ofTaking old mild steel hinges carefully without damaging and refixing in the same or other opening as directed. Nothing extra cost will be allowed in this account.

Taking down cement plaster, terrazzo dado in any thickness from brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc including removal of rubbish,vegetation etc outside complex (MOD land) complete all as specified and directed.

S&F Fiber Glass Reinforced Plastic (FRP) Door Frames of cross section 90mm x 45mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.

S&F 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardantgrade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames complete all as specified and directed.

M&L Frame work as in door chowkhats with angle iron welded together ends of angle shouldered and fixed to opening and welding 3 Nos mild steel butt hingese, and 6 nos hold fasts made out of FI 25x3 mm 30 cm long for fixing of chowkhats( Butt hinges paid separately) complete all as specified and directed

All as per item No.20 above but fixing only ditto. Note any additional items will be paid under item No.20 above

M&L framed work such as grills, grating etc with ends of bars shouldered or riveted or forged into spikes framed guard bars, railing and similar work confirming to Fe - 290-0 or E-165 including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

S&F 35mm thick factory made flush shutters solid core construction with block board core and plywood face panels commercial type on both sides complete all as specified and directed.

M&L Factory made 2nd class hard wood glazed and skeleton shutter 35mm thick, factory made, open rebated and prepared to receive glass/guage etc, without sash bars, mitred and rebated, with edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/guage etc, sizes of members of shutter as specified in section 8, clause 8.24(a) of SSR Part I complete all as specified and directed.

S&F 25 mm thick flush shutter solid core construction with block board core and ply wood face panel commerical type on both side to be fixed as shutter of cupboard/kitchen cup board/loft board including two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F 100 mm long (size) butt hinges, medium weight, cold rolled mild steel, complete all as specified.

S&F 75 mm long (size) butt hinges, medium weight, cold rolled mild steel, complete all as specified.

S&F 300mm long, Aluminium anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts complete all as specified and directed.

S&F in repair aluminium anodised grade barrel tower bolt 200 mm long, extruded section complete all as specified and directed.

S&F aluminium anodised barrel tower bolt 200 mm long , extruded sections complete all as specified and directed.

S&F extruded aluminium alloy handle of size 150mm size long complete all as specified and directed.

S&F in repair aluminium anodised floor door stopper with hard drawn steel spring 140mm long complete all as specified and directed.

S&F Aluminium anodised floor door stopper with hard drawn steel spring 140mm long complete all as specified and directed.

S&F in repair 300mm long, Aluminium anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts complete all as specified.

M&L Cement concrete 1:2:4 type B1(using 20mm graded crushed stone aggregate) as in bed blocks for hold fast, coping, benching etc. including weathering, slightly rounded or chamfered angles or throating including form work to concrete surfaces complete all as specified and directed upto two storey height.

S&F Hasp and staple, 75mm size, safety type, brass with mild steel hinge pin including bolt to hinge plate & fixed with screws, complete all as specified and directed

S&F in repair 40mm dia, cup boards stainless steel knobs fixed with nuts , screw and washer of mild steel bright finished complte all as specified and directed

S&F 150mm size double action spring, hinge, mild steel with steel wire spring, stove enamelled black, complete all as specified and directed.

S&F Continuous piano hinges stainless steel of AISI 304 grade width of flaps (when open) 30mm complete all as specified and directed.

M&L Preparation of new or previously untreated wood and wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and directed.

Providing and fixing factory made UPVC any colour sliding window. Three track of area n exc 2.00 Sqm each made of extruded profiles with wall thickness of 2.3mm (+0.2mm). Window profile with hollow section with multi chamber, frame ((88mm x 52mm), sliding sash (42mm x 67mm), sliding mesh sash (42mm x 57mm) sliding interlock (one vertical length in each shutters) (45.5mm x 28mm). Glazing bead (24.5mm x 16mm) will be mitred cut and fusion welded at all corners, including railing of holes for fixing hardware and drainage of water etc, making arrangement for fixing of hardware EPDM gasket, 1.2 + 0.2mm thick galvanized steel frame (30mm x 18) 02Nos, sliding sash(30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in reqd. Profile, frame will be fixed to the wall with 8mm x 100mm long fasterners. Hardware ( Touch lock of zinc alloyed (any colur powder coated) , steel roller system, including 5mm thick toughened glass with single glazing bead and weather seal, stainless steel wire cloth 0.36mm nominal dia of wire and avg width of aperture 1.40mm and required accessories). Note:- Net opening will be measured for payment purpose.

M&L Granite of 18 to 20mm thick with uniform texture (table rubbed and polished) in steps, jambs, pillars, window cills,cooking platforms and like in cement mortar (1:4) including pointing with white cement (1:2) using marble dust with admixture of pigment to match with marble shade of makrana doogri green colour stone for Kitchen cooking platform laid over and including 15mm thick screed bed in cement mortar (1:6) polishing bevelled edges of corner etc complete all as specified and directed. Note: - The granite slab of window Sill shall be in single piece.As far as possible the granite slab of cooking platform in the kitchen shall be of single piece, but total number of joints shall not be more than two. Any deviation from this instruction shall be regularized with minus price adjustment if the work is technical acceptable.

All as per serial item no 44 above but on vetical surfaces including 15 mm thick rendering in cement mortar 1:4

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with steel wire staples, complete all as specified and directed

M&L for Brick work with sub class B bricks of old size, straight or curved on plan exc 6 m mean radius, built in cement mortar 1:6 complete all as specified and directed.

Ditto all as per item No.47 above but except bricks ditto.

M&L for Brick work with sub class 'B' bricks straight or curved on plan to any radious in half brick thick wall built in CM 1:4 complete all as specified and directed.

Ditto all as per item No.49 hereinbefore but except bricks ditto.

S&F Mild steel TMT bars of 10 mm dia and over cut to length bent to shape required including cranking, bending etc and for stengthening existing reinforcement by use of mild steel bars of any dia , cut to length, bent to shape required, including cranking, bending spirally and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for providing reinforced cement concrete (1:2:4) type B-1 using 20 mm graded crushed stone aggregate as in kitchen slab, Chajjas, lintels complete all as specified and directed. Note : The rate quoted by the contractor is deemed to include the necessary scafoldings, supports etc. Nothing extra will be claimed on this account. The work will be executed upto G+3 Storyes building.

M&L Kota stone slab 18-20 mm thick with uniform texture in floor (size 580mm x 580mm) with laid over and including 15 mm thick screed in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed

M&L kota stone slab with uniform texture of 18-20 mm thick in treader of steps, riser of steps, skirting, dado and pillars in one single piece (size decided by Engineer-in-Charge) laid over and including cement screed 15mm thick in cement morter 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing , bevelled edge of corner etc complete all as specified and directed.

S&F Form work to sides and soffits of shelves etc including supports such as kitchen shelves, platforms and similar works rough finish surface of concrete (the thickness of slab/shelves n.exc. 100 mm) complete all as specified and directed.

M&L for 5 mm thick rendering in cement mortar 1:3 on concrete surfaces of ceiling, chajja and like surface finished even and smooth without using extra cement complete all as specified.

M&L for rendering 15mm thick external plaster of ready mix plaster with mix plaster with CM 1:6 of approved make on fair faces of brick work or stone work or conc surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick internal rendering in cement mortar 1:6 on fair face of brick walls/ concrete surfaces & finished even and smooth without using extra cement, complete all as specified.

M&L Non skid Coloured ceramic rectified tile 300x300x7-8 mm thick as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L Coloured ceramic rectified tiles 300x600 x 7 to 8mm thick, as in vertical surfaces of wall such as dado/skirting, set and jointed in neat cement slurry and pointed in white or coloured cement over and including 10mm thick rendering in CM 1:4 complete all as specified.

M&L Coloured ceramic rectified tiles 600mm x 600mm x10 mm thick , joint free as in floors over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L Coloured glazed ceramic rectified tiles 600 mm x 600 mm x 10 mm thick as in skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

S&F 15mm bore GI tubing medium grade with all fittings and fixed to wall and ceiling or laid in floors etc complete all as specified and directed.Note :-The pipe shall be painted with bituminous paint of approved quality and the pipes should not come in contact with lime mortar or lime concrete as pipes are affected by lime etc.

All as per item No 63 above but 20 mm bore.

S&F white colour Rotational moulded polyethylene water storage tank 1000 litres capacity, ISI marked triple layer construction (cylindrical vertical closed top), hoisted & fixed in position including all fittings complete all as specified and as directed.

S&F in repair viterous china squatting pan 'ORISSA Pattern' size 580x440mm white with integral foot rests incl P or S Trap) (excluding flushing cistern & flush pipe) complete all as specificed and directed.

S&F vitreous china white coloure flat back wash hand basin 550mm x 400mm complete, Ist quality, incl provn of pair of mild steel angle iron brackets of suitable size duly painted and cutting for and pinning in ends of brackets in walls,making good incl providing and fixing of suitable CP Waste & Pipe complete all as specified.

S&F in repairs PVC valveless syphonic action flushing cistern 10ltr capacity, low level, white with inlet, ball valve, float and handle incl brackets and connection to pipes and fixing of chain and pull or lever if any complete all as specified.

S&F Brass CP basin mixer for mixing hot & cold water screwed down for iron pipe 15 mm bore, screwed down high pressure, screwed for iron pipe and fixed complete all as specified and directed. Make:- Cera Cat Part No F3001461, Jaquar Cat Part No VTG 9167B, Marc Cat Part No MOR 1100 or equivalent

S&F sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracked guard and railing 60 cm long complete all as specified and directed.

S&F stainless steel sink AISI 316 grade without drainage board of 1 mm thick kitchen or laboratory with plug , washer and waste, 15mm bore brass Chromium plated sink mixer for mixing hot and cold water, bedding in cement morter to dwarf wall or including CP Waste , PVC Down pipe etc and fixing cantilever brackets and connecting union to pipe overall Size 330mm x 255mmx150mm etc compete all as specified and directed.

S&F stainless steel kitchen plate rack 1 mm thick four shelves made out of stainless steel sheets 1 mm thick overall size 1200mm x 900mm x 250mm complete all as specificed and directed.

S&F Chromium plated tubular towel rail, 20mm dia, ‘D’ type 60cm long between flanges of brass chromium plated and fixed with brass screws all as specified. Make Cera Cat Part No S9010111, Jaquar/Marc/Parko or equivalent.

S&F stainless steel peg set of six complete all as specified and directed.

S&F in repairs 15 mm bore Angle valve cast copper alloy Chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe complete all as specified and directed. Make- Cera Cat Part No F1001201, Jaquar Cat Part No VTG 9053, Marc Cat Part No MOR 1060A or equivalent

S&F wall mixture 15 mm bore cast copper alloy Chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe complete all as specified and directed. Make- Cera Cat Part No F1001411, Jaquar Cat Part No VTG 9219, Marc Cat Part No MOR 1141 or equivalent.

S&F in repairs 15mm bore bib taps fancy type of Chromium plated high pressure screwed for iron pipe and fixed etc. complete all as specified and directed. Make- Cera Cat Part No F1001151, Jaquar Cat Part No; VTG 9037, Marc Cat Part No MOR 1020A or equivalent.

S&F in repairs CP brass shower rose 125mm dia with chromium plated arm fixed to 15mm pipe of revolving type complete all as specified and directed. Make- Cera Cat Part No F7010506, Jaquar Cat Part No; OHS 489 & SHA 479L450, Marc Cat Part No MOR 1050 or equivalent.

S&F in repair Stainless steel grating 100mm dia of best quality as approved by GE including fixing in CM 1:4 to floor/nahani traps etc complete all as specified .

S&F in repair Gun-metal globe or gate valves 20mm bore with iron wheel head, screwed both ends for iron iron complete all as specified and directed.

S&F 20mm dia Ball brass valves, high pressure, with polythene float and fly- nut com-plete, scre-wed for iron pipe or brass ferrule , plastic ball screwed for iron pipe and fixed complete all as specified and directed.

S&F in repair PVC connection 15 mm bore and 45cm long with washers complete all as specified and directed.

M&L Preparation of new or previously untreated steel surfaces of any description over 10cm in width or girth,not otherwise specifically and applying two coats of synthetic enamel paint over a coat of redoxide primer complete all as specified .

S&F 100mm dia (bore of pipe) cast iron (sand cast) soil, waste, vent pipe in any length with or without ears with cement joint fixed to walls, complete all as specified.

All as per item 85 above but except pipes

S&F 75 mm dia (bore of pipe) cast iron (sand cast) soil, waste, vent pipe in any length with or without ears with cement joint fixed to walls, complete all as specified.

All as per item 87 above but except pipes

S&F in repair 100mm dia (bore of pipe) cast iron Tee diminishing pieces or tapers (larger bore measured) with cement joints, complete all as specified.

All as per item 89 above but 75mm dia (bore of pipe) Tee

S&F 75mm dia (bore of pipe) branch pieces single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches, fitted with oval access door, complete all as specified.

All as per item 91 above but 100mm dia (bore of pipe).

S&F in repair cast iron floor trap square type with Cockroch Proofing CP grating with or without hole including provision of jointing to waste pipes in run lead joint dia of outlet 75 mm, complete all as specified.

S&F in repair 100 mm pipe, stack clamps out of 50mmx 5 mm flat iron and 16 mm dia round iron stamp including bolts and nuts and securing ends of stays to walls or roof complete all as specified and directed.

All as per item No 94 above but 75 mm bore pipe.

M&L 19mm thick MDF boards, grade 1 quality, exterior grade, commercial type, fixed with screws to timber frame-work face complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

S&F Drappery curtain rods decorative type stainless steel 25mm nominal dia of approved quality (3mm wall thickness) including fixing of two number decorative brackets fixed in brick/concrete wall, Two number of latto on both ends of curtain rods ( The length of each curtain rod will be 1.00m to 1.50m long) complete all as directed and specified.

BLANK

M&L for applying a coat of bituminous primer conforming to IS - 3384 @ 0.50 Litres/qm on prepared surfaces of plaster and applying APP based polymeric membrane with mineral slate finish @ 4.00 Kg/Sqm and minimum 3mm thick reinforced with polyester non woven fabric and sealing joints by torch application complete all as specified and directed. Note : The work will be executed by authorised manufacturers/applicator

M&L Screed bedding 20mm thick plaster in CM 1:4 on roof finished even and fair using integral water proofing admixtuire.(Note : Supply only water proofing admixture shall be measured and paid separately) complete all as specified and directed .

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws and the sheet should be embedded in to the wall to a depth of 25mm and the surfaces to be plastered and made good complete all as specified and directed

S&F Framed bracket of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary,gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 complete all as specified and directed

M&L for 75 mm thick cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection laid in bays & surfaces finished fair and even without using extra cement, complete all as specified.

M&L for providing pre cast RCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate as in culvert slab/landings etc including form work complete all as specified & directed.

M&L Resecuring or Easing and adjusting , without taking down shutters of doors/windows for easy opening /closing ,tightening of hinges and changing its position or adjustment of tower bolts/sliding bolts etc area not exc 2 sqm each complete all as specified and directed.

M&L Cement concrete 1:2:4 type B0(using 12.5mm graded crushed stone agg) as in roof levelling complete all as specified and directed

M&L Cement concrete type B1-1:2:4 (using 20 mm graded crushed stone agg) in roof kerbs or mud stop rounded or chamfered on edge etc complete all as specified and directed

M&L for complete removal of existing treatment on surfaces of walls/ceilings by scrapping down with mechanical grinder on old walls as per the specification of manufacturers instructions of paints/OBD complete all as specified and directed.

M&L for preparation of newly plastered or unplastered surfaces of walls complete all as specified and directed.

All as per item No. 110 above but on ceilings

M&L for applying of wall care putty on newly/old plastered walls of 2-3mm thick including preparing the surface with even and smooth complete all as specified and directed. (Note : Wall putty to be procured from manufactures directly)

M&L Preparation of newly/old plastered surfaces of walls and applying two coats of Oil bound distember on walls complete all as specified and directed.

M&L Preparation of newly/old plastered surfaces of walls and applying two coats of white wash on walls complete all as specified and directed.

M&L Preparation of newly/old plastered surfaces of ceilings and applying two coats of white wash complete all as specified and directed.

M&L 150mm dia Intercepting traps of salt-glazed stoneware, with square ends to inspection arms for building flush into manholes and setting in cement mortar 1:1 complete, including concrete foundation of width and thickness as for pipes of same dia and haunching after setting. Cleaning arm to include a glazed ware stopper, galvanised iron bayonet joint (or other approved pattern) and galvanised iron lever (or trigger), galvanised iron chain, hook and ring complete all as specified and directed.

M&L for applying one coat of alkali resistent primer on already prepared surfaces of walls complete all as specified and directed.

M&L Preparation of newly/old plastered surfaces of walls and applying two coats of cement base paint walls/ceilings complete all as specified and directed.

M&L for Preventive treatment against the danger of carbonation in exposed faces of RCC members :- (i) Cleaning existing surfaces of RCC members and making surface free of loose material, oil, grease etc. by vigorous wire brushing including light grit blasting where necessary as recommended by Engr-in-charge. (ii) Further, cleaning using biocide(as recommended by manufacturer) to ensure that surface is free of algae and fungus and no trace of paint (any type) left out. Sand blasting to be done to remove trace of paint. (iii) Cleaned surface to be allowed to dry. (iv) Spray a coat of primer (as recommended by manufacturer) over dry cleaned surface as required prior to final finish. Primer shall be diluted in proposition 2:1 with mineral turpentine. After application, primer shall be allowed to dry for 03 hours or as directed. (v) Apply a coat of neat Aliphatic Acrylic anti-carbonation (ACC) over the primed surface with air / spray gun at nominal rate of 3.5 ltrs per sqm as recommended by manufacturer. (vi) Apply a more coat of Aliphatic Acrylic anti-carbonation (ACC) after 5-6 hours as recommended by manufacturer complete all as specified and directed.

M&L for followings :- (i) Removing plaster & finishes all around the coloumns, slabs & beams (on all four sidescription of column to full height , three sidescription of beam to entire span & bottom of slab to area as directed) (ii) After cleaning gently removing cover concrete using pneumatic/electric chipper or any other approved tool in entire portion of structural member (removal of cover concrete shall be done to an extent when reinforcement is visible) (iii) Removal of cover concrete with under cutting of up to a depth of 20mm beyond reinforcement around full circumference & full length of bar where directed. (concrete shall be stripped to an extent concrete substrate is exposed) (iv) Cleaning exposed concrete substrate by using water jet. (v) Removing visible rust along the length of reinforcement using hand tools as approved. (vi)M&L for providing rust proof /anti corrosive treatment to bars as per manufacturers instrucions.

(vii) cleaning of all exposed bars (new & old) alround (viii) Apply a single coat of Alkaline rust converting primer on alround bars new & old as recommended by the manufactuer (ix) Apply two coats of Epoxy phenolic anti corrosive protective coat on bars alround new & old as recommended by the manufactuer. Note : Anti corrosive treatment shall be continuous espcially in the regions where pitting, imperfections, etc were present on the surface of the bars. It is important that the rear portions of re bars (those towards the concrete substrate) should not be left without coating. (The Engr-in-charge may order sand blasting if rust is approved) (x) Any other work as directed by Engr-in-charge to present clean surface for determination of type of repair to be carried out complete all as specified and directed.

M&L for providing PMM (Polymer modified cementitious mortar) :- (i) Dry sub strate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible.(In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of 25 mm thickness. Note : Application of PMM shall be preferably be in coats of appx 10mm thickness. PMM work shall be executed in fairely rapid successions so as entire work is completed with in 30 mins). PMM shall be pre packed ready to use. (iv) PMM surface to be moist cured for three days followed by air curing in temperature as recommended by manufactuer complete all as specified and directed.

M&L for treatement of cracks found in the core concrete :- (i) Opening of crack by making a ' V' notch/groove of size 12mm x 12mm over the entire length of the crack as identified by the Engr-in-charge. (ii) cleaning ' v' notch/groove of all dust/debris/loose material (iii) Drilling hole of 16mm dia and about 40mm deep along the length of crack @ (300 mm c/c or thickness of structural member whichever is less) Note : In case length of crack is found less than 300 mm then min 2 holes shall be drilled. (iv) Inserting 12 mm dia flexible PVC one way injection nipple in the hole drilled above and fixing the nipple with the help of fast setting epoxy putty. (v) seal the surface around the nipple and the area of crack between successive nipples polymer modified mortar to ensure that there is no leakage from any gap. (vi) Allow the PMM to cure for 24 hours and ensure that firmly fixed in postion. (vii) cleaning nipple one by one commencin from the top to bottom in case of column and one by one in alternate direction incase of beam/slab using blow compressed air followed by water injection. An Ensuring that there is no obstruction in free flow of grouting materials complete all as specified and directed.

(viii) Injecting " resin with very low viscosity monomer by mixing resin and hardener in proportions recommended by manufacturer by using injection gun equipped with pressure gauge & valves for controlling of flow of compressed air & resin. Note : pressure shall be in the range of 1-2 kg/sqm and shall be done in nipples one by one as per order recommended by manufacturer. Mixing of resin and hardenere shall be mixed in small quantities so as it is consumed with in 30 minutes. Before use mixer shall be stirred thoroughly. (ix) Allow entire effected surface to cure for 24 hours. (x) cutting out projected parts of the nipple & seal the hole in the nipple with epoxy putty as recommended by manufacturer. (xi) cleaning exposed surface of substrate off any dust /loose material after ageing of the grout as recommended by manufactuer. (NOTE : THE RATE QUOTED IS INCLUSIVE FOR ENTIRE COMPLETION OF WORK. THE MEASUREMENT FOR THE ABOVE ITEM IS MADE FOR EACH SET OF HOLE COMPLETE ALL AS SPECIFIED)

M&L for treatement of core concrete when found to be porous/honeycombed :- (i) Marking the area in marker as directed by the Engr-in-charge. (ii) Drilling holes of upto 16mm dia in an orthogonal grid on exposed cone of member @ 150 mm c/c both way, depth of the hole shall be about 60% of the element thickness. (iii) clean the drill hole using compressed air removing the dust/dirt. (iv) Inserting 12 mm dia flexible PVC one way injection nipple in the hole with the annular space around the nipple sealed with epoxy putty. It shall be ensured that the injected grount does not leak. (v) Allow the nipple to cure for 24 hours. (vi) Injecting " Resin with very low viscosity monomer by mixing resin and hardener in proportions recommended by manufacturer by using injection gun equipped with pressure gauge & valves for controlling of flow of compressed air & resin. Note : pressure shall be in the range of 2-3 kg/sqm and shall be done in nipples one by one as per order recommended by manufacturer. Mixing of resin and hardenere shall be mixed in small quantities so as it is consumed with in 30 minutes. Before use mixer shall be stirred thoroughly. (vii) Allow entire effected surface to cure for 24 hours. (viii) cutting out projected parts of the nipple & seal the hole in the nipple with epoxy putty as recommended by manufacturer. (ix) cleaning exposed surface of substrate off any dust /loose material after ageing of the grout as recommended by manufactuer.

M&L for Providing & Pouring Micro concreting M-40 grade :- (i) Dry concrete substrate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound concrete substrate using approved spray machine & ensuring that no pin holes are visible. (In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above pour Micro concreting M40 grade, using approved mixing machines/pumping under pressure via approved pneumatic pump at the locations to be repaired in RCC beams & columns etc,. Adding of aggregates will be permitted only as per manufacturer’s recommendation without compromising the strength. The rate shall include cost of all materials (except re-bar) labour charges for mixing, pouring concrete, cost of tools, lead & lift of materials, transportation etc., to carry out the complete work complete all as specified and directed. Note : The cost of micro concrete M-40 grade & Epoxy bond coat is inclueded in this item.

M&L for Drilling & chemical anchoring of new rebars/stirrups :- (i) Drilling in to the sound RCC members for anchoring of rebars/stirrups as directed, the dia of hole to be match with dia of rebar & length of drilling as under :- 8 mm dia bar - drilling length 80 to 100 mm - 384 Nos Note : Anchoring of new re-bars of any dia as directed in to the sound RCC members as directed using pure epoxy resin anchoring mortar with appropriate diameter of drilling of holes as mentioned above for proper bonding into the concrete etc., complete. (The cost of drilling hole & chemical anchoring with epoxy resin is inclueded in this item)

M&L for Drilling & chemical anchoring of new rebars/stirrups :- (i) Drilling in to the sound RCC members for anchoring of rebars/stirrups as directed, the dia of hole to be match with dia of rebar & length of drilling as under :- 16 & 20 mm dia bar - drilling length 160 to 180 mm - 700 Nos Note : Anchoring of new re-bars of any dia as directed in to the sound RCC members as directed using pure epoxy resin anchoring mortar with appropriate diameter of drilling of holes as mentioned above for proper bonding into the concrete etc., complete. (The cost of drilling hole & chemical anchoring with epoxy resin is inclueded in this item)

M&L for use & waste of form work using steel sheets , steel bracing, propping etc around structural members where micro concreting to be done and keeping form work in position till required specified period complete all as specified and directed. Note : Form work shall be 100% leak proof. For purpose of payment area in touch with concrete shall be measured.

M&L for chipping of spalled and loose concrete and cleaning rust from re-inforcement by sand brushing scrubing down concrete surfaces with wire brushes cleaning with water allowed to dry applying a layer of zinc rich epoxy primer as antirust on all exposed reinforcement followed by a layer of bonding coat of a layer of epoxy adehessive on complete exposed surfaces of concrete and provide guniting in two layers over steel welded mesh 2 mm dia of wire and total aperture 75 mm, thickness of gunite n.exc 25 mm thick (average thickness) using cement mortar 1 :3 with OPC 43 grade cement mixed with polycrete admixture @ 2 % by wight of cement or as per manufactures instructions and finally applying cement plaster over gunite surfaces of required thickness to give an even uniform and smooth finish conforming to proper Geometrics in cement mortar 1:4 to match with the existing surface as in side and soffits of slabs,chajjas,fins,facias ,parapets ,columns and beams etc complete including necessary scaffolding ,shuttering necessary chased to brick work or RCC members at any height upto four storey buildings incl removing of small trees shrubs etc all as specified(Note: steel welded mesh to be welded with the existing reinforcement. The cost of welded meshis to be welded with the existing re-inforcement is deemed to be included in the quoted rate complete all as specified and directed.

Impregnating cream for injection into masonry or concrete wall 230 mm thick against capilary rising humidity complete all as specified and directed. (make: RIsing bar super strong of chowgale or equivalent ) Method of Applicaion Methodology (a) The surface must be sound, absorbent, clean, free of dust, oil, paint, curing agents, loose cement or lime plaster & concrete, debris, or any separation layers. (b) The plaster must be knocked off at least 50 cm beyond the visibly penetrated area. (c) Damaged mortar joints are to be scraped out to a depth of approximately 2-3 cm. All sharp edges/joints need to be levelled ; loose concrete to be removed. (d) Drill boreholes at ground level horizontally. The boreholes are drilled horizontal into the masonry.

(e) The holes should be drilled until a depth of approx 5 cm (for a 6cm thick wall) before the end of the wall is reached. The boreholes should have a diameter of 12mm upto a maximum of 15mm and should be spaced approx. 100 to 120mm apart and the vertical offset is 6 cm max. (f) Before inserting RisingBar Super Strong or equivalent the boreholes must be cleaned from boring dust by using air pressure. It is not necessary to pre-wet the borehole. (g) For applying of RisingBar Super Strong or equivalent the dosing system inserted as far as possible into the borehole. While dosing the product uniformly, the injection nozzle is pulled out leading to a completely filled borehole (h) Treatment of highly absorbent masonry might require repeated filling of the borehole. Depending upon extent of damage, RisingBar Super Strong or equivalent can be re-injected into the same hole after 24 hours. Depending on absorbency, application or masonry thickness 0.1 to 0.15 litre/m with 10 cm wall thickness.

M&L for Providing & injecting chemical for post construction ATT along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc in a portion with cement mortar 1:2 to match the existing apron complete all as specified and directed.

M&L for Post Construction anti termiteTreatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor sall as specified and directed.

BLANK

S&F factory made PVC frame of size 75x40mm with wall thickness of 4mm made out of extruded 4mm thick plain or prelam PVC sheet reinforced with 15x15mm MS square tube of 19 gauge thickness through out the frame and mitred cut and two corners and jointed with two nos of 150mm long bracket of 10x10mm MS Square tube. The door frame shall be fixed to the wall using 65x100mm long MS screws though the frame by using PVC fastners minimum of four Nos of screws to be provided for each vertical members and minimum of two nos of screws to be provided horizintal members etc complete all as per manufacture instructions and directed by Engineer-in-Charge.

S&F 18/19mm thick PVC moulded solid board one side prelam for cabinet boxes etc with self and shutter full size fitted under/above the kitchen cooking platform and other platform complete all as specified and directed as per drg incl provn of fixing arrangement

All as per Item No 65 above but 500 Ltr capacity

All as per Item No 65 above but 300 Ltr capacity

All as per Item No 72 above but overall size 900mm x 800mmx250mm

All as per Item No 72 above but overall size 600mm x 600mmx250mm

All as per Item No 82 above but overall size 600mm x 600mm x 5.5mm thick

S&F stainless steel sink with drainage board AISI 304 grade of 1mm thickness for Kitchen including waste/washer, 15mm bore CP sink mixer for mixing for mixing hot and cold water, bedding in cement mortar to dwarf wall including CP waste coupling and PVC waste pipe and connection union over all size 1145mm x 510mm bowl size 560x410x215mm etc complete all as specified and directed.

S &F Stainless steel grill AISI 304 grade using 10mm thick size hollow square bar (100mm c/c) weight not less 0.62 Kg/mt including necessary frame and accessories for window and ventilator grill complete all as specified and directed

M& L for complete decommissioning and commissioning of IGL pipe line along with IGL metre in each block up to the length of 5.00 mtr (approx) complete all as specified and directed. NOTE:- THE DECOMMISSIONING AND COMMISSIONING SHALL BE CARRIED OUT BY REP OF IGL ONLY. THE CERTIFICATE DULY SIGNED BY REP OF IGL SHALL BE SUBMITTED TO GE OFFICE IMMEDIATELY AFTER THE COMPLETION OF JOB.

Providing working space including pruning of trees and vegetation clearance near bilding upto the distance of 3.00m from the periphery of the building complete all as specified and directed.

S&F in repairs vitreous China coloured European type WC with "P" or "S" trap for 100 mm bore , including connection to drain and to flushing cistern with pipe 32mm dia PVC pipe and fixing bolts complete all as specified and directed.

S&F stainless steel sink with drainage board AISI 304 grade of 1mm thickness for Kitchen including waste/washer, 15mm bore CP sink mixer for mixing for mixing hot and cold water, bedding in cement mortar to dwarf wall including CP waste coupling and PVC waste pipe and connection union over all size 1000mm x 510mm bowl size 460x410x200mm etc complete all as specified and directed.

S&F mild steel 150mm ordinary rat tail, rod pattern springs including roller and roller plate complete all specified

S&F of 150mm dia UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed complete to walls, celings or indoors with suitable clamps/bracket including taking down old PVC/Cl pipes and necessary cutting through RCC roof and brick work etc (G+1) and making good all as specified

S&F of 150mm dia UPVC (SWR) bend any radius with solvent joints, complete all as specified and directed

S&F of 150mm dia UPVC (SWR) Tee any radius with solvent joints, complete all as specified and directed

Disconnecting existing tanks of exc 250 ltr and n exc 500 ltr capacity, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position.

Disconnecting existing tanks of exc 500 ltr and n exc 1000 ltr capacity, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position

M&L Flush Pointing to 30cm by 15cm brick tiles with CM 1:4 laid in Roof Terrace complete all as specified and directed

M&L for Preparation of Roof surfaces of any description over 10cm width or girth not otherwise described and applying two coats of Heat Resistant reflective Aluminium Paint over APP Membrance or brick tiles or concrete surface complete all as specified & directed.

M&L for Supreme quality Heat Resistant Terrace Tiles of size 250x250x18 to 20mm thick over and including 15mm thick screed in CM 1:4 all as specified and directed.

S&F stainless steel three drawer set of the kitchen cabinet system of overall size 500X600X800mm with the following specified Stainless steel 304 bracket (i) Raw material:- Stainless steel AISI 304 grade, dia 10mmX19 SWG (ii) The bracket base stainless steel AISI 304 grade dia 3mm (iii) Support bar of stainless steel AISI 304 grade dia 5mm (iv) Finish: Electro polished or buff (v) The three drawer set shall consist of the following units:- (a) Cutlery unit: Perforated curtlery unit made out of perforated stainless steel 304 grade with perforated channel with provision of size 435x550x100mm and is fitted with telescopic channel. (b) Cups and saucer unit made out of stainless steel 304 grade of size 435x550x100mm and fitted with telescopic channel to carcass all as specified. (c) Plate rack: plate rack made out of stainless steel 304 grade of size 435x550x100mm and fitted with telescopic channel all as specified.

S&F stainless steel three drawer set for the kitchen cabinet system of overall size 500x600x800mm with the following specifications Stainless steel 304 grade bracket (i) Raw material:- Stainless steel AISI 304 grade, dia 10mmx19 SWG (ii) The bracket base stainless steel AISI 304 grade dia 3mm (iii) Support bar of stainless steel AISI 304 grade dia 5mm (iv) Finish: Electro polished or buff (v) The three drawer set shall consist of the following units (a) Normal drawer unit top:- Normal drawer unit made out of stainless steel 304 grade of size 435x550x100mm and is fitted with telescopic channel as shown in the sketch. (b) Normal drawer unit bottom:- Normal drawer unit made out of stainless steel 304 grade of size 435x550x100mm and is fitted with telescopic channel as shown in the sketch (c) Plate rack: plate rack made out of stainless steel 304 grade of size 435x550x100mm and is fitted with telescopic channel all as shown in the sketch.

S&F stainless steel one tier pullout set out for kitchen cabinet system of over all size 800x600x800mm with the following specifications (i) Stainless steel AISI 304 grade, dia 12mmx19SWG (ii) The bracket base stainless steel AISI 304 grade dia 3mm (iii) Support bar of stainless steel AISI 304 grade dia 5mm (iv) Finish: Electro polished or buff (v) Heavy duty storage drawer unit bottom made out of stainless steel 304 grade of size 735x550x100mm and is fitted with telescopic channel as shown in the sketch

S&F stainless steel one tier spice rack for the kitchen cabinet system of overall size 200x600x800mm including SS 304 grade tray, PWCT carcass with the following specifications. Stainless steel 304 grade for tray (i) Raw material:- Stainless steel AISI 304 grade, dia 10mmX19 SWG (ii) The bracket base stainless steel AISI 304 grade dia 3mm (iii) Support bar of stainless steel AISI 304 grade dia 5mm (iv) Finish: Electro polished or buff Spice Rack should consist of stainless steel 304 grade of size 130x550x100mm and is fitted with telescopic channel

S&F stainless steel One tier soup rack for the kitchen cabinet system of over all size 200x600x800mm including SS 304 grade tray, PWCT carcass with the following specifications . Stainless steel 304 grade for tray (i) Raw material:- Stainless steel AISI 304 grade, dia 10mmX19 SWG (ii) The bracket base stainless steel AISI 304 grade dia 3mm (iii) Support bar of stainless steel AISI 304 grade dia 5mm (iv) Finish: Electro polished or buff Soup rack should consist of 1 racks of stainless steel 304 grade of size 130x550x100mm and is fitted with telescopic channel as specified.

S&F Stainless steel 304 grade dustbin stand for the kitchen cabinet system of 8 litres capacity with PVC lid and bucket.

Supply only 550mm telescopic channel for fixing cabinet dooors in kitchen cabinet system which allows the cabinet door to close smoothly with minimum weight bearing capacity of 40kg

S&F Auto closing hinges for fixing cabinet doors in kitchen cabinet system with self closing mechanism which allows the cabinet door to close smoothly.

S&F Fancy type 100mm long SS handle with extruded section fixing with SS screw complete all as spd

Description of Work / Item(s)

Amount

Taking down carefully copper/aluminium point wiring from wooden battan or conduits (light, fan, socket or power) complete including (fittings such as switches, ceiling roses, pendants, regulator, sockets etc. to be measured separately) and making good disturbed surfaces of walls, floor etc.

Taking down old MCCB , TPN DBs , SPN DBs, & main switch/ enclosure box of any make and type from the site and making good surface complete all as specified and directed.

Taking Down old submain wiring of any size includng conduit & make from the site complete all as specified and directed.

Taking down old unsv light fitting of any size and make from the site and making good surface complete all as specified.

Taking down old carefully unserviceable recess mounted 2"x2" (4x14 watt) light fitting of any make and type from the pop hard pop false ceiling without damaging the existing false ceiling structure and making good the disturbed surfaces around the light fitting with POP and matching with the existing colour.

M & L for Point wiring complete with 1.5 sqmm single core PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor drawn through and including non-metalic rigid new PVC conduit medium grade ISI Marked not less than 20 mm dia and all conduit accessories concealed in wall on surface in ceiling/fixed to roof/truss/columns etc and including provision of 1.5 sqmm PVC insulated copper cable FRLS as earth continuty, fabricated modular metal flush box, concealed in walls with suitable modular inner and outer plate for housing switches , socket out let and fan regulators etc, complete all as specified.

(a) One light /Ceiling fan/exhaust fan point controlled by one switch.

(b) One 3 pin 5 Amps socket outlet point controlled by one No one way switch on same board

(c) One 3 pin 5 Amps socket outlet point controlled by one No one way switch on independent board.

(d) One bell point controlled by one bell push.

(e) One light point controlled by two Nos two way switches

M&L point wiring with PVC unsheathed multi stranded copper conductor cable 4 sqmm FRLS 1100 Volts in New PVC concealed conduit medium grade ISI Marked not less than 20 mm dia in new MS steel terminal boxes modular including one run of using 4 sqmm FRLS 1100 Volts copper conductor cable as earth continuity connected to common earth for one 15 A switch socket power point, all as specified

M&L switch Modular type 6 Amps one way ISI marked 230V AC complete all as specified.

M&L switch modular type 6 amp SP two way ISI marked complete all as specified.

M&L Modular socket outlet 5 pin 6 Amp socket 2 module ISI marked complete all as specified.

M&L switch bell push Modular type 6 Amps 1W-1 module, ISI marked 230V AC complete all as specified.

M&L switch Modular type 16 Amps one way ISI marked 230V AC complete all as specified.

M&L Modular socket outlet 5 pin 6/16 Amp universal socket 2 module complete all as specified.

Supply & Fix Modular five stepped type electronic fan regulator 2 module ISI marked 230V AC complete all as specified.

M&L bell electric (ding dong) 230 volt, SP all as specified and directed.

M&L point wiring with PVC insulated FRLS 1100 Volts unsheathed cable 1.5 Sqmm multistranded copper conductor and drawing concealed in wall & including nonmetalic rigid new PVC conduit medium grade ISI Marked not less than 20 mm dia of conduit, terminal box of 1.6 mm thick and 3 mm thick hylam sheet cover for terminal boxes also including porvision of earth wire PVC insulated FRLS 1100 Volts unsheathed 1.5 sqmm stranded copper conductor single core cable connected to common earth dolly the following :

(a) One light/fan/bell point controlled by one by one way switch.

(b) One light point controlled by two, two way switch.

(c) -ditto- as above item No 16 but One 3 pin socket outlet 5 hole 5 Amp independent board socket & switches to be measured and paid separately.

(d) -ditto- as above item No 16 but Same board.

M&L One power point with insulated stranded copper conductor cable 4 Sqmm single core for 3 pin 15 Amp switch socket and PVC insulated FRLS 1100 Volts unsheathed copper conductor 4 Sqmm in and including new PVC conduit medium grade not less than 20 mm dia, stranded conductor as earth wire connected to dolly complete.

M&L for submain wiring with two single core PVC insulated FRLS 1100 Volts unseathed stranded copper conductor cable 4 Sqmm in and including new PVC conduit medium grade not less than 20 mm dia, for submain wiring and connection complete FRLS 1100 volts unsheathed stranded copper conuctor cable of 4 Sqmm size stranded conductor as earthwire.

M&L for submain wiring with two single core PVC insulated FRLS 1100 Volts unseathed stranded copper conductor cable 6 Sqmm in and including new PVC conduit medium grade not less than 20 mm dia, for submain wiring and connection complete FRLS 1100 volts unsheathed stranded copper conuctor cable of 6 Sqmm size stranded conductor as earthwire.

M&L for submain wiring with two single core PVC insulated FRLS 1100 Volts unseathed stranded copper conductor cable 10 Sqmm in and including new PVC conduit medium grade not less than 20 mm dia, for submain wiring and connection complete FRLS 1100 volts unsheathed stranded copper conuctor cable of 10 Sqmm size stranded conductor as earthwire.

M&L switch piano flush type 5 Amp SP one way ISI marked complete all as specified and directed.

M&L switch piano flush type 5 Amp SP two way complete all as specified and directed.

M&L switch piano flush type 15 Amp SP one way ISI marked complete all as specified and directed.

M&L bell push,flush type,5 amp ISI marked complete all as specified and directed.

M&L socket outlet 5 pin 5 Amp flush type ISI marked complete all as specified and directed.

M&L socket outlet 2 in 1,3 pin 5/15 Amps ISI marked complete all as specified and directed.

M&L ceiling rose 3 phase PVC polycorbonate, isolated body complete all as specified and directed.

S&F electronic fan regulator 5 step ISI marked connecting complete all as specified and directed.

M&L angle Lamp holder with metallic ring, PVC/Polycorbonate type with back plate complete all as specified and directed.

S&F LED bulb 12 watts, 1200 lumens output, 6500K suitable for B-22 base complete all as specified and directed.

M & L for earthing complete with galvanized steel earth plate 600x600x6mm thick buried vertically in ground to depth not less than 2.25 mtr below ground level, with top edge of the plate not less than 1.50 mtr below normal ground level, connected to earth lead GI 4mm dia by means of bolts, nuts, check nuts and washers of galvanized iron and connection to main switch board of panel, including watering pipe GI 20 mm bore light grade 15mm bore for earthing lead, wire mess, funnel, salt, charcoal dust, excavation and refilling pit with PCC 1:2:4 type B1(using 20mm dia stone aggregate) reinforced with 6mm dia round bar @ 75mm cement concrete both always with MS handle 12mm dai and frame all as shown in electric plate No 3 in page 497 of SSR Part I (2009) including testing ion completion all as directed

M&L for earth continuity conductor or main earthing lead fixed to wall on batten or recessed or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc 4 mm dia galvanised or steel wire complete all as specified.

S&F MCB DB SPN 12 way Horizontal, IP - 43 Protection double door 240 V AC 50Hz with for MCB SPN as incomer and SP MCBs as out going with tinned copper bus bar ,neutral link earth link complete.

Supply and fix MCB DB SPN 8 way Horizontal, IP - 43 Protection double door 240 V AC 50Hz with for MCB SPN as incomer and SP MCBs as out going with tinned copper bus bar ,neutral link earth link complete.

S&F MCB SPN 63 Amps 240 volts 10 KA 50 HZ 'C' curve complete all as specified and directed.

M&L MCB SPN 40 Amp "C " curve complete all as specified and directed.

M&L MCB SP 6 to 32 Amp "C" curve complete all as specified and directed.

Supply and fix LED batten luminaire surface mounted, 4 feet system wattage of 22 Watts with lifetime of 50000 burning hours with 70% of its initial lumen maintained. CRI>80, Power Factor > 0.95, THD< 10%, colour temperature - 6500K, surge protection 2.5KV in CM, IP-20 protected, meets LED IS specifications, Class - 1, Short circuit and over circuit protection, voltage range - 150 to 270 Volts AC, temperature range 0 to 50 DegreeC, system efficacy at luminarie level > 100 Lumens/watt and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting fixed complete.

Supply and fix LED batten luminaire surface mounted 2 feet system wattage of 10 watts and not less than 900 lm system lumen output with life time of 50000 burning hours with 70% of its initial lumen maintained. CRI > 80, power factor > 0.95, THD < 10%, color temperature > 6500 K , surge protection 2.5 KV in CM IP- 20 protected meets LED IS specifications, short circuit and over circuit protection, voltage range - 150 to 270 volts AC, temperature range 0 to 50 Degree C, and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire fixed complete.

Supply and fix 10 watts bulkhead fitting with powder coated die cast aluminium housing with glass/ non yellowing polycarbonate cover, IP65 Protection, System level efficacy of the Luminary is > 90 lm/W with a life class of 50,000 burning hours at L70 criteria, Power Factor >0.95, driver with Voltage range 150-270V, Temperature range 0 to 50 Deg, Driver efficiency >85%, THD<10%, CRI>80, Color Temperature-6500K, Surge protection of 4.0 KV, including connecting up with necessary PVC sheathed 3 core 1.5Sqmm copper conductor flexible wire fixed complete.

Supply and fix surface ceiling mounted, round LED down light fitting 12 watts with die cast aluminium housing and system wattage of 12W, system efficacy at luminary level ≥ 80 Lumens/watt, 50000 burning hours, 6500K color temperature with CRI >80, Power Factor > 0.90, Driver should meet IEC compliant for safety with multi stage high Isolate CC-CV operated driver with voltage variation range - 150 to 270 Volts AC, and surge protection of 2.5 KV, and including connecting up with PVC sheathed 3 core 1.5Sqmm copper conductor flexible wire fixed complete.

supply and fix recessed mounting LED FLAT panel 2"x2" made of crca sheet steel duly power coated with high efficient LED and glaire free full opal diffuser , IP 20 Suitable for 36 watt,230 volts ,50 Hz AC Supply, Neutral White,with electronic driver and incluiding all fixing accessories complete.

Supply and fix surface ceiling mounted,squre LED down light fitting size (1 ft x 1 ft), 12 watts with die cast aluminium housing and system wattage of 12W, system efficacy at luminary level ≥ 80 Lumens/watt, 50000 burning hours, 6500K color temperature with CRI >80, Power Factor > 0.90, Driver should meet IEC compliant for safety with multi stage high Isolate CC-CV operated driver with voltage variation range - 150 to 270 Volts AC, and surge protection of 2.5 KV, and including connecting up with PVC sheathed 3 core 1.5Sqmm copper conductor flexible wire fixed complete.

Supply & fix in repair factory made epoxy powder coated Distribution Board TPN-4 ways with metal door (IP-43 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removeable gland plates with knockouts and suitable for one TPN- MCCB 125/160 Amp as incomer and 40 to 63 Amp SP MCBs outgoing complete all as specified and conforming to IS : 8623.

M&L in replacement MCCB 125 Amps, 16 KA , 4P, complete.

Supply and fix 45 W High efficient LED Street light fitting with pressure die cast LM6 Aluminum housing and has lenses specially designed for Street Lighting with polycarbonate cover. System level efficacy of the Luminarie is 100lm/W with a life class of 50,000 burning hours at L70. The color temperature is around 6500 K with a color rendering index of 70. The luminaire is IP:66 protected with IK05 impact resistance. It has an electronic driver complaint to IEC safety standards with a power factor>.0.9, voltage variation range 120-270V, THD<20%, High and low protection along with a surge protection of 4 KV including provision of 40mm dia GI light grade pipe1.5 meter length bend to shape and necessary clamps etc for fixing the light fittings on pole fixed complete

Taking down carefully the existing ceiling fan of 1200mm from its position after disconnecting electric connection and deposits in MES Store all as specified and directed.

Supply and fixing ceiling fans three blade, Robust and reliable inverter motor (brush less DC Motor) powered by ECM technology, BEE 5 star rating for energy saving, rated Air delivery >220 cum/min, service valve > 6, AC single phase 230/240 V of size 1200 mm sweep including making connection with three core flexible, copper cable pvc insulated of suitable length, complete all as specified and directed. Note: Ceiling Fan must operated on electronic Regulator, it should not be remote operated.

S&f fresh air fan PVC body air delivery > 800 CMH , 5 number of blades, AC single phase 230/240 V of size 250 mm sweep with louvre fixed complete with suitable size ply by cutting into suitable size as required complete.

S&F sheet metal enclosure single pole and Neutral with a two pin earth plug and socket complete with a MCB SP 20 Amp 230 volts, 50 Hz, 10KA breaking capacity complete.

S&F sheet metal enclosure single pole and Neutral with a two pin earth plug and socket complete with a MCB SP 10 Amp 220 volts, 50 Hz, 10KA breaking capacity, including fixing completly in wall with sutable sand and cement, complete.

S&F water heater storage type Geyser ABS body vertical type with suitable size of fastner and including provision and connecting up of SS braided pipe with adopter for inlet and outlet water connection having adjustable knob for temperature control and inner tank should be glass line coated, capacity 25 Ltrs, having heating element 2 KW and not less than 5 star rating, suitable for ,230 volt, 50 Hz electric supply complete all as specified and directed .

S&F exhaust fans AC single phase 230/240 V of size 300 mm sweep, Air flow rate > 900cum/min, Bird screen for protection against birds, double ball bearing, heavy duty, metal body with louvre metal body with louvre for fixing of exhaust fan complete all as specified and directed.

M &L telephone Point wiring complete with single pin 0.61mm dia copper conductor cable telephone pain taped and rip conforming to ITD specification D-3003 and ITI-113C/114C cable PVC insulated drawn though PVC concealed conduit not less than 20 mm dia for one 2 pin telephone socket out let on independent modular type board.

Supply & Fix in repair RJ-11 Telephone socket with transparent shutter 1 module on phenolic laminated sheet etc as required.

Taking down carefully the existing Exhaust fan of 300mm rom its position after disconnecting electric connection and deposits in MES Store all as specified and directed.

S&f Wall mounted fans AC single phase 230/240 V, of size 400 mm sweep, aerodynamic design, air delivery >70 CMM, 3 blade, double chord, thermal overload protected motor, speed RPM 1400, Sturdy and shock proof body for fixing of wall fan complete all as specified and directed.

Supply and fixing wall mounted, 5 watt decorative LED picture light fitting complete all as directed.

M&L for breaking the old existing wall and making provn of a round hole for fixing of 300 mm sweep exhaust fan including making good to the disturbed wall/ portion and matching with existing colour.all as specified and directed.

Taking down carefully the existing ceiling fan of 1200mm from its position after disconnecting electric connection and checking it for its serviceability and refixing after painting all as specified and directed.

Taking down carefully the existing Exhaust/Fresh air fan of any size from its position after disconnecting electric connection and checking it for its serviceability and refixing all as specified and directed.

M&L for earthing of machinery/ equipment/ panel/ installed at power house/subatation, complete with galvanised steel earth palte electrode 600 x 600 x 6 mm thick buried directly in ground (Earth pit not less than 2.5 mtrs deep below ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level connecting to galvanised iron strip 25 x 4 mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel and earth protected by 40 mm dia GI pipe medium grade and connected to distribution board/earthing test point all as shown in electrical plate No.3 of SSR Part-I )2009) and testing on completion all as specified and directed.

Taking down carefully the existing Old U/S Geyser capacity 25 Ltr its position after disconnecting electric & water connection and deposits in MES Store all as specified and directed.

Fluorescent tube light fitting. 1 x36W flameproof type FLP-WP made ofaluminium alloy LM6, with electronic ballast, bipin holders, connector block,etc. complete with all accessories prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size

Point wiring in steel conduit unsheathed multistrand copper conductor cable 1.5 sqmm single core FRLS for one light point / fan point / bell point controlled by Flame proof switch including continuous earth continuity insulated PVC unsheathed (green colour) 1.5 sqmm copper earth wire connected to common earth dolly complete all as specified and directed by the Engineer-in-Charge.

S&F Switch flame proof rotary type with termination box in LM6, 16A, single pole 250V

S&F air termination, Single pointed aluminium rod 12mm dia and 300 mm long complete all as specified and directe.

M & L for fixing aluminium strip 25 x 3 mm complete duly fixed on porcelain/epoxy insulator with the help of nut, bolt, and washers etc for roof and down conductor above ground (all the joint shall be properly riveted and brazed welded) complete all as specified and directed. Note:- For srl item No. 2 insulator will be measured and paid separately in item No.-4

M&L GI pipe light grade 40mm dia with all fitting and fixed complete to wall and ceiling or lad in floor for fixing of GI/Aluminium strip or protection of lightening conductor complete all as specified and directed.

S&F porcelain/ PVC insulator of suitable size to fixed GI/ Al strip 32x6/ 25x3 mm as earth continuity conductor or main earthing lead buried in ground (All the joints shall be properly) riveted and brazed/welded) complete all as specified.

M&L earth test point terminal block made of gun metal or phosphorous bronze size 75x75x25mm drilled and screwed including 3 Nos 8mm dia 25mm long hex. Head screw complete all as specified and directed.

Taking down old earthing & GI strip complete all as specified & directed.

M&L earthing complete with GI electrode 600x 600 x 6mm, thick buried directly in ground vertically in a pit of depth not less than 2.25 mtr below normal ground level (with top edge of earth plate not less than 1.50 mtr below normal ground level connected to GI strip 32x6mm as earthing lead by means of bolt nuts, check nuts, and washers of brass connected including gun metal or phosphorus bronze of sixe 75x75x25mm drilled and screwed including 3 Nos 8mm dia 25 mm long hexagonal head screwed all as specified including excavation and earth work and disposal of surplus soil incl 40 mm GI tubing light grade and necessary fitting for protection of GI strip incl laying of charcoal dust and common salt PPC (1:2:3) type C-1 (using 20mm graded stone aggregate) for earth pit with 40 x 40 x 6mm MS angle iron frame for cover 40 mm thick (1:2:4) type B20 using 12.5 mm graded stone aggregate reinforced with 8 mm dia round bar @ 75mm C/C both way with MS handle 20mm dia plastering 15mm thick CM (1:6) internally and upto 150mm below ground level externally PGL funnel with ground wire mesh 20mm dia Med grade GI pipe for watering complete all as shown on electrical plate No 3 of SSR Part-1 2009 and connected in earth test incl testing completed all as specified and directed. Note:- GI strip and protecton light grade GI pipe upto 7.5 mtr shall be deemed to be in the rates.

M&L for Providing PCC 1:2:4 type B-1 20 mm graded aggregate for GI tubing post for lightening protection complete all as specified and directed.

ASSOCIATED CONSTRUCTION CO.

NSC Projects Pvt. Ltd.

Third Wave Services Pvt Ltd

Khairati Lal

India Guniting Corporation

AMIT ASSOCIATES

AMIT ASSOCIATES

India Guniting Corporation

Third Wave Services Pvt Ltd

NSC Projects Pvt. Ltd.

Khairati Lal

m/s meetu enterprises