SPL REPAIR TO BLDG NO P-14 AND P-06 AT KHETOLAI AND PUMP HOUSE AT LATHI UNDER AGE (I) POKARAN

Amount

Dismantling Stone slabs in roofs, suspended floors , chajjas, landings, etc., any thickness, jointed in any mortar complete all as specified and as directed by the Engineer-in-Charge.

Demolition of concrete of any description and in any position (PCC Padding over roof) complete all as specified and as directed by the Engineer-in-Charge.

Demoliton of RCC Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similars complete

M&L for PCC 1:2:4 type BO using 12.5 mm graded stone aggregate for levelling course for consolidated thickness shall be varied from 25 to 85 mm as per the requirements all as directed by Engr-in-Charge.

M&L for jodhpur stone roof slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, hoisted, set, jointed and grouted in lime mortar 1:3 or cement mortar 1:6 complete complete all as specified and as directed by the Engineer-in-Charge

M&L for jodhpur stone roof slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, hoisted, set, jointed and grouted in lime mortar 1:3 or cement mortar 1:6, except stone slabs complete all as specified and as directed by the Engineer-in-Charge

M&L for Flush Pointing single joints in brickwork or masonry in detached work, flashings, etc. on ceiling in CM (1:4) complete all as specified & directed.

Supply only integral Waterproofing compound.

M&L for laying of APP based polymeric membrane minimum weight 3Kg/Sqm and minimum 3mm thick reinforced with polyester non woven fabric (wt not less than 150gm/sqm) laid on primed surface by torched application complete etc all as per manufacturer instructions and sealing all the over laps of 75mm in length side and 100mm on the width side of membrane all as specified and directed including following (i) Taking down the existing roof treatment of any description , any thickness and removing the debris not exceeding 1000 m. (ii) Preparing the surface of roof slab by brushing with wire brushes for removing of loose/ dirt material etc and sweeping with brooms or gunny bags or mechnical devices. (iii) Applying neat cement slurry with 3Kg of cement per sqm & mixing of liquid water proofing compound as per manufacturer instruction on surface of roof slab (iv) Screed bed 10 mm thick in CM (1:4) on concrete surfaces with mixing of liquid waterproofing compound as per manufacturer’s instructions and finishing the surface even and smooth without using extra cement (v) Priming the suraface of concrete/plaster with bituminous primerconfirming to IS-3384 applied at 0.3 liter per Sqm (vi) Applying 2 coat of Al paint @ 100 ml/sqm (vi) M&L for PCC 1:2:4 type BO using 12.5 mm graded stone aggregate for levelling course for consolidated thickness 40mm as per the requirements

M&L for roughly squared stone 5cm thick as in lintels n exc 3m in length, hammer dressed on face and soffits, hoisted, set and pointed in lime mortar 1:3 or cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge

Dismantling of Stone slabs and tiles of any description or thickness in floors, walls, aprons etc., removing serviceable tiles to store and rubbish off the premises.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) remaining serviceable tiles to stores and rubish off the premises

M&L for Vitrified ceramic tiles , Light Shade, 10mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floor etc set jointed and pointed in white or coloured cement to match the colour of tiles with screed or bedding layer of mortar 15mm thick for laying floor finishes in CM 1:6. all as specified.

.M&L all as per item No- 13 but in skirting over & including 10mm thick backing coat of CM 1:4 all as specified.

S&F for Non- skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with screed bed 15 mm thick CM 1:6 complete all as specified & directed

M&L Glazed ceramic coloured tiles in vertical surface 300 x450x7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick rendering CM1:4 complete all as specified and directed.

Demolition of stone/ boulder masonry and built in cement mortar all as specified & directed by Engineer-in-charge.

M&L for squared rubble walling, Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) all as specified & directed by Engineer-in-charge.

M&L for squared rubble walling, Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) but except stone all as specified & directed by Engineer-in-charge.

Extra over stone walling for hammer dressing to face stones with maximum depression on face from a straight edge not exceeding 20mm & dressing face beds and joints as specified to squared rubble walling Jodhpur type brought up to courses all as specified & directed by Engineer-in-Charge.

M&L for Brickwork with flyash bricks,modular size, straight or curved on plan to any radius in half brick thick walls built in CM 1:6

M&L Rendering 10mm thick on fair faces of brick work or concrete surfacesin CM 1:6, Surface finished even and fair w/o using extra cement

Taking down cement plaster on brick or stone walls including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

M&L rendering 15mm thick in 1:6 cement plaster on stone masonary surface is to be finished even and smooth (without using extra cement) complete all as specified and directed.

M&L rendering 15mm thick in 1:4 cement plaster on of stone masonary surface is to be finished even and smooth (without using extra cement) complete all as specified and directed.

M&L for 10 mm thick , plaster in cement mortar (1:4) on surfaces of ceiling and finishing the surface even and smooth without using extra cement all as specified & directed by Engineer-in-charge.

M&L for preparation of new plastered surfaces as in ceilings, applying 3 coats of white wash complete.

M&L preparation of new wall surface and applying two coats of distemper oil emulsion over a coat of alkali resistant primer,including 3mm thick wall care putty on wall complete all as specified and directeded.

Complete removal of existing treatment and applying chalk whiting (putty) on plastered surface, preparatory to distempering, priming plastered and other surfaces with alkali resistant priming paint and applying two coats of OBD on wall.

M&L for preparing old painted surfaces by washing, rubbing down and stopping of distempered and painted surfaces and applying a coat of white wash on surfaces of ceiling complete all as specified & directed by Engineer-in-charge.

Complete preparation new surfaces of walls and preparation of surfaces old (external faces) of walls and applying two coats of external weather proof paint of Apex or equivalent over a coat of primer (self coat) complete all as per manufacturers instructions, complete all as per specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sq. m each complete all as specified and as directed by the Engineer-in-Charge

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.5 sq. m but not exc 4 sq. m each complete all as specified and as directed by the Engineer-in-Charge

Joist, channel, angle, or tee sections, fixed independently, without connection plate, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated), Fe 410-W (Gde E-250) quality A

S&F 35mm thick factory made plain framed, panelled shutters (two panels) With lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (Part-I), kiln seasoned and chemically pressure treated all as specified.

S & F, 35 mm thick factory made second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc size of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (a) complete all as specified & directed by Engineer-in-charge.

S&F PVC door frame size 50mm x 47mm made out of 5mm plain coloured PVC sheet reif with MS square tube supplying & fixing in opening as per specification.

S&F factory made solid panel PVC door shutter 28 to 30mm thick (Stile) with 2,4 or 6 raised panels design with 2mm thick moulded PVC sheet on the front face and 2mm plain colour on back face

S&F SS Hinges100 mm size and fixed

S&F Aluminium anodised, barrel tower bolt of extruded section and fix of length 150mm

S&F Aluminium handles, cast type, anodised of size 150mm long.

S&F 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F Factory made Box Type steel window with side hung shutters including projecting type hinges with steel handle, and steel peg stay , complete with glazing bars, dovetailed or complete as shown in Drawing No. CEJZ/TD/22 sh 1/1 to 1/3, and all as specified & directed by Engineer-in-Charge.

S&F Factory made Box Type steel window with side hung shutters including projecting type hinges with steel handle, and steel peg stay , complete without glazing bars, dovetailed or complete as shown in Drawing No. CEJZ/TD/22 sh 1/1 to 1/3, and all as specified & directed by Engineer-in-Charge.

S&F Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con-forming to Fe 290.Gde-E-165

S&F 4 mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.50 sqn in each pane.

S&F stainless steel wire cloths 0.36mm nominal dia of wire and averaging width of aperature 1.40mm and fixed with stainless steel wire staples complete all as specified & directed.

Preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and direction.

Preparation of new Steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and direction.

S&F in repair for 05 cm thick Jaisalmer stone slabs in chajjas/shelves,cills, landings, manhole cover stones, etc and like n exc 2.00m in length, punched dressed on face and along exposed edges, self faced on other side and set & pointed in cement mortor 1:4, complete all as specified.

S& F MS work joist, beam, channel,angle, or tee,sections, fixed independently ,with out connecting plates,etc cut to ordinary lengths i.e with in 20 mm of the length indicated.etc using EWR on inducion butt welded tubes conforming to FE-410W(Gde-E-250)-B

Demolition of wall ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets.

S&F for anodised aluminium snap grid 605 x 605 mm frame work for false ceiling all as specified and directed.

M&L for PVC insulation panels with EPS stuck to 10 mm thick plain PVC sheet suitably placed in false ceiling grid made of Aluminium/G.I./M.S.

S&F Hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long complete all as specified

S&F Solid PVC wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed.

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification and drawing.

S&F in repair of Brass chromium plated shower rose 125mm size

S&F in repairs 15mm bore dia conceled/Angular stop valves chromium plated fancy type , screwed down , high pressure ,screwed both ends for iron pipe or for union and fixed complete all as specified and directed

Supply and fix repairs decorative type curtain rod , stainless steel, 25 mm dia with not less than 1mm wall thickness complete all as specified and directed.

Supply and fix decorative type brackets , stainless steel, suitable for above curtain rod complete all as specified and directed.

M&L for 50 mm thick PCC (1:3:6) type C-1 using 20 mm graded stone aggregate as in plinth protection all as specified and directed

Demolition of cement concrete unreinforced in groundfloors and pavings not exc 15cm thickness below or above ground level etc all as specified and as directed

Supply and fix rotational moulded polyethylene water storage tanks ( cylindrical vertical with closed top ) hoisted and fixed in position all as specified in SSR part-I ,1000 ltr capacity including dismantling of water tanks and removing to store capacity of tank exc 500 and n exc 1000 ltr.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth

S&F Medium grade GI tubing 15 mm bore with all fittings , to walls, ceiling or laid in floors etc including taking up or down steel tubing and connections including cleaning for refixing or removal to store 15 mm bore to walls, ceiling etc.

S&F Medium grade GI tubing 20 mm bore with all fittings , to walls, ceiling or laid in floors etc including taking up or down steel tubing and connections including cleaning for refixing or removal to store 20mm dia pipe.

S&F gun metal globe or gate valves with iron wheel head screwed both end for iron pipe and fixed in repairs to 15 mm bore pipe.

S&F gun metal globe or gate valves with iron wheel head screwed both end for iron pipe and fixed in repairs to 20 mm bore pipe.

S&F in repairs for stop cock copper alloy but fancy type and chrominum plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron/pipe or for union and fixed 15 mm bore in repairs

S&F counter top wash basin of Cat No - 1023 with out utility counter (under or over & semi recessed) type clair , size 520 x 450 MM of colour Snow white , Make - Cera

S&F towel rail 600 mm long of Brass C.P 'D' type fixed with and including chromium plated brass screws and wooden /plastic cheats in repairs

S&F PVC (SWR) pipes of 75 mm dia, single socket fixed to walls and floors

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc complete, drilled for fixing of steel sheeting or other covering. Door, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings(exclusive of steel sheeting or other covering, running rails & guides) and hanging also fastening & complete all as specified & directed by Engineer-in-charge.

M&L 25mm Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

M & L for add in repair of Pillar taps, cast copper alloy, with capstan heads, chromium plated, fency type crewed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed

S&F grating doom 100mm dia of PTMT

M&L for white Marble tiles 20mm thick machine cut, bedded jointed and pointed with grey cement slurry including cutting and polishing types

M&L for Chequered cement concre tiles 20 cm x20 cm x25 mm thick, set, jointed and pointed in neat cement slurry in floors in coloured cement to match complete all as specified and directed including screed bed 15 mm thick in CM (1:6)

M&L for RCC M 25 concrete using 20 mm graded stone aggreagte fo slab supported on walls, beams,floors, landings and similar works complete all as specified and as directed.

M & L for TMT bars 10mm dia and over cut to length, bent to shape reqd, including cranking and binding with and including MS wire annealed) not less than 0.9mm dia or securing with clips quality confirming to Fe 410-w or E-250 complete all as specified and directed

M & L for TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders and binding with and including MS wire annealed) not less than 0.9mm dia or securing with clips quality confirming to Fe 410-w or E-250 complete all as specified and directed

Formwork to edges of floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide

Dismantling of cast iron Rcc, Ac or PVC pipe jointed in CM up to 150mm dia bore

S&F PVC (SWR) pipes of 110 mm dia, single socketed fixed to walls

(PVC (SWR) vent cowl, 100 mm dia

M&L for cement epoxy grouting on RCC wall and base floor of under ground water sump as per manifacturers instructions all as specified and directed

Taking down carefully point wiring of any type (i.e. on wooden batten, surface conduit, casing-N- capping or concealed conduit) complete for light, fan socket or power point with fittings & fixtures such as ceiling rose, electric fittings, holders, switches, sockets, regulators, wooden batten, conduit etc. including accessories such as wooden gutties/rawal plug, screw etc including making good disturbed surface to match the existing surface all as specified & directed.

Taking down carefully by unscrewing from boards/outlet boxes, fittings and fixtures such as switches,sockets, ceiling roses, lamp holders, brackets, ceiling fittings, bulk head fittings, tube light fittings and regulators, etc. for reuse at site or carrying to the store (To be measured only when found serviceable in all respects complete for reuse)

Taking down carefully sub main/ service cable / wiring of any nos of wire and size with earth wire on wooden batten/surface conduit/casing-N-caping complete with its all accessories

M&L for point wiring with PVC unsheathed cable single core stranded copper conductor 1.5 sq mm size, 1100 V grade, drawn into concealed conduit medium grade (ISI marked) not less than 20mm dia on surface with and including PVC unsheathed cable single core copper conductor 1.5 Sq mm as continuous earth wire and including pressed MS sheet sunk in box 1.12 mm thick with 2.8 mm thick laminated bakelite sheet all as specified & directed by Engr-in-charge for One light/fan/Exhaust point controlled by one switch 5 Amp one way

Ditto- all as per item no 92.but socket outlet 3pin 5 amps same board

Ditto- all as per item no.92 but socket outlet 3pin 5 amps independent board

Ditto- all as per item No.92 here-in-before but for one socket outlet/metal clad socket of 15 Amps fixed on independent board with 4.0 Sq mm multistranded copper conductor wire FRLS PVC insulated and 2.5 Sq mm copper conductor wire FRLS PVC insulated using as earth wire complete all as specified and directed by Engineer-in-Charge

M&L Modular white cover plate with frame ( both inner plate & outer plate cover ), 1 module.

M&L Modular white cover plate with frame ( both inner plate & outer plate cover ), 2 module.

M&L Modular white cover plate with frame ( both inner plate & outer plate cover ), 3 module.

M&L Modular white cover plate with frame ( both inner plate & outer plate cover ), 4 module.

M&L Modular white cover plate with frame ( both inner plate & outer plate cover ), 6 module.

Modular metal flush box 1 & 2 module

M&L Modular metal flush box 3 module

M&L Modular metal flush box 4 module

M&L Modular metal flush box 6 module

M&L in repair, Modular switch one way 6 Amp single pole & one modular.

M&L in repair, Modular socket 6 Amp 2/3 pin combined shattered ISI marked confirming to IS 1239 : 1997 having finger proof terminals with captive screws having front fixing & removing features without removing plates.

M&L in repair, Modular socket 16/6 Amp 3 pin combined shattered ISI marked confirming to IS 1239 : 1997 having finger proof terminals with captive screws having front fixing & removing features without removing plates.

M&L in repair Modular switch 16 Amp single pole one way ISI marked confirming to IS 3854 : 1997 or latest IS having finger proof terminals with captive screws having front fixing & removing features without removing plates.

S&F in repair, Electronic type modular fan regulator step type 120 watt, 230 volt. 01 module

S&F in repair, sheet metal enclosure DB's 240 Volts, IP-43, suitable for mounting MCB's, SPN, 4 way with 200 Amps rated copper bus bar double door type complete all as directed by Engineer-in-charge.

S&F in repair, sheet metal enclosure DB's 240 Volts, IP-43, suitable for mounting MCB's, SPN, 8 way with 200 Amps rated copper bus bar double door type complete all as directed by Engineer-in-charge.

M&L in repairs MCB SP 240 volts, 5 to 32 Amps, 10 KA

M&L in repairs MCB SPN 240 volts, 40 Amps, 10 KA

M&L in repair, Lamp holder PVC polycarbonate type with back plate suitable for battern fittings

S&F LED 15 watt

Ceiling rose, 3 phase/PVC/polycarbonate, isolated body

S & F in repair Decorative box type fitting 1x 16w, blue coloured end caps, prewired for LED tube including LED tube 16 watts, including connecting up with twin core twisted flexible copper conductor cable with suitable size complete and all as specified and directed by Engineer- in Charge.”.

Supply and fixing recessed mounting LED Square downlighter luminaire with die cast aluminium housing 15 watts incl provn of three core cable size 1.5 Sq.mm from ceiling rose to fitting with all accessories and all as specified and directed by Engineerin Charge Make- Crompton greaves Limited LSDN-15-CDL/TL/WW or Equivalent make of Havells/Philips.

S & F in repair, LED building Security light fitting 1x18watt with polycarbonate housing ,Aluminum gear tray duly prewired inbuilt LED module IP 65 Protection complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of size 1.5 sq mm including GI tubing 40mm dia light grade 1.5m long band to shape for mounting of security light with 2 nos MS,FI clamp including plinth with nut bolts etc complete all as specified and directed

S&F 40 W LED, IP65 Rated LED Post Top ideal to lit up parks, garden ways and heritage sites. resistant to impace and corrosion. glare-free and better uniformity with necessary 32/40mm GI tubing for fixing the lights as site requirement (Make :- Crompton Greaves Cat Part No.LPTH-20-CDL or equivalent as approved by GE) complete all as specified & directed by Engineer-in-charge.

M & L for earthing complete with galvanized steel earth plate electrode 600x600x6.3 mm thick, burried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less 1.5 mtr deep below normal ground level connected to GI earth wire 4 mm dia connected to earth plate by means of nut, bolts, check nut & washer of galvanized iron or of steel, GI earth wire will be protected by 15 mm dia GI pipe 'light grade', watering pipe 20 mm dia GI 'light grade', GI wire meshed funnel, alternate layer of char coal and salt on all side to earth plate upto thickness of 150 mm, filling of black cotton soil in earth pit upto ground level, PCC chamber recessed for and including RCC cover including all necessary excavation & earth work, earth wire connected to O/H continious earth wire on pole, testing the earthing after completion all as specified and shown in electric plate No 5 of MES SSR Part-I 1991 print and as directed .

M&L in repairs for submain wiring with PVC unsheathed cable single core stranded copper conductor 6sq mm size, 1100 V grade, drawn through PVC conduit medium grade (ISI marked) not less than 25mm dia on surface with and including PVC unsheathed cable single core copper conductor 4.0 Sq mm as continuous earth wire and all as specified & directed by Engr-in-charge.

Taking down old unserviceable LT cable, supply and Laying in trenches/through pipes/ducts or on poles/walls jointing to O/H conductor, LT panels, main switch with cable size aluminum lugs and testing. XLPE insulated, armoured heavy duty electric cables with aluminum conductor, 1100 volt grade, all as specified directed by Engineer In charge of cross sectional area of 10 Sqmm 2 core

Excavation in trenches not exc 1.5m wide and n. exc 1.5M deep for fdn / trenches and getting out for soft / loose soil.

Removing excavated material n exc 50m and depositing at a level n.exc 1.5M above ground.

Returning/filling in layers, spreading leveling, watering and well ramming in layers n.exc 25m in sof/loose soil.

M&L for Tibba sand for sand cushioning to under ground cable including, spreading, leveling hand punning complete all as specified and directed.

Supply and laying Jodhpur stone patti for cable protection of lenth between 55 to 60 cm but width between 25 to 30 cm thicknes not less than 5 cm complete as per site requirement and direction of engineer in charge.

Habib Traders

M/s Shri Inder Construction Company