Construction of 120 seated ST Boys Hostel at UGHS, Papuluru (Konda Reddy)

Earth work excavation in stony earth, and gravel mixed with stone and boulders not exceeding 0.014 cum in volume within 50M intial lead and 1.5M initial lift including rough dressing and breaking clods to maximum 5 cm to 7 cm and laying the layers not exceeding 0.3M depth and as per specification approved by the Department.and as directed by the E.I.C. a) Ordinary Soil

b) Soft Rock

c) Hard Rock

Extra for every additional lift of 1.5 M or part there of in excavation / banking excavated or stocked materials a) Ordinary soil

Supplying & Filling foundation trenches , plinth & ditches with clean course river sand well watered and rammed in layers not exceeding 23 c.m. in depth with all lead and lift including cost, conveyance, loading, unloading, stacking,royalties and all taxes of sand,cost & conveyance of water, cost of all Labour,labour cess,T&P required for the work etc. complete in all respect as directed by the Engineer- in -charge.

Back filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5m.

Making plinth protection 150 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth etc. complete as per direction of the E.I.C.

With Chlorpy;rophos / Undone E.C 20% with 1% concentration

Providing and laying P.C.C[1:4:8] using 4cm size metal etc in foundation and floors using cement , 40 mm size crusher broken H.G.Metal and screened and washed sharp river sand for mortar of approved quality and from approved quarry including hoisting ,lowering and laying concrete to the required level, ramming ,watering and curing etc

Providing and laying in position ready mixed M25 grade concrete having compressive strength at 28 days test not lessthan 250kg/sq.cm for reinforced cement concrete work using cement content as per approved design mix etc including Rigid & smooth centering and shuttering. I) For R.C.C foundation, footing bases of column, mass concrete,pre-cast etc.

II) For R.C.C plinth band etc.

III) R.C.C Beam & Coloum a) Ground Floor

b) 1st Floor

c) 2nd Floor

d) Terrace Floor

Iv) Lintel a) Ground Floor

b) 1st Floor

c) 2nd Floor

d) Terrace Floor

v) RCC Stair a) Ground Floor

b) 1st Floor

c) 2nd Floor

VI) Chajja a) Ground Floor

b) 1st Floor

c) 2nd Floor

d) Terrace Floor

Vii) Roof Slab Landing Balcony a) Ground Floor

b) 1st Floor

c) 2nd Floor

d) Terrace Floor

Cutting ,Straightening coiled or bend up HYSD/TMT Reinforcement bars welding or jointing if necessary , bending ,tying the grills as required for R.C.C works etcwinding wire extra Foundation

a) Ground Floor

b) 1st Floor

c) 2nd Floor

d) Terrace Floor

Fly Ash Brick Masonry in cement mortar of mix (1:6) using Fly Ash bricks of size 23cmx11cmx8cm in Foundation & Plinth having crushing strength not less than 75 kg per square c.m. with cement and screened & washed sharp sand for mortar after immersing the bricks for 6 (Six) hours in water before use in works with all necessary projections, splays cutting, circular moulding, corbelling, chamfering, watering and curing etc. including cost, coveyance,stacking, loading, unloading, royalties , all taxes ,cost of all labour,Labour cess ,scaffolding, sundries and T&P required for the works etc. complete in all respect as directed by the Engineer-in-charge. Foundation and Plinth

Fly Ash Brick Masonry in cement mortar of mix (1:6) using Fly Ash bricks of size 23cmx11cmx8cm in Foundation & Plinth having crushing strength not less than 75 kg per square c.m. with cement and screened & washed sharp sand for mortar after immersing the bricks for 6 (Six) hours in water before use in works with all necessary projections, splays cutting, circular moulding, corbelling, chamfering, watering and curing etc. including cost, coveyance,stacking, loading, unloading, royalties , all taxes ,cost of all labour,Labour cess ,scaffolding, sundries and T&P required for the works etc. complete in all respect as directed by the Engineer-in-charge. a) Ground Floor

b) 1st Floor

c) 2nd Floor

d) Terrace Floor

Fly Ash Brick masonry in cement mortar of mix [1:4] using Fly Ash bricks of size 23cmx11cmx8cm in superstructure having crushing strength not less than 75 kg /m2 etc[Half Brick work] a) Ground Floor

b) 1st Floor

c) 2nd Floor

Providing 12mm. Thick cement plaster in cement mortar or mix(1:6) in all floors at all height with cement & screened and washed sharp river sand for mortar and finished smooth to the rough surface of the brick masonary walls after racking out the joints (alongwith providing grooves wherever necessary) including watering and curing,rounding of corners etc. complete with cost,conveyance, loading, unloading, royalities and taxes of all materials,cost of all labour,T&P,sundries and scaffolding required for the work etc. as directed by the Engineer-in- charge.

b) 1st Floor

c) 2nd Floor

d) Terrace Floor

Providing 16mm. Thick cement plaster in cement mortar or mix(1:6) in all floors at all height with cement & screened and washed sharp river sand for mortar and finished smooth to the rough surface of the brick masonary walls after racking out the joints (alongwith providing grooves wherever necessary)including watering and curing,rounding of corners etc. complete with cost,conveyance,loading, unloading,royalities and taxes of all materials,cost of all labour,T&P,sundries and scaffolding required for the work etc. as directed by the Engineer-in- charge. a) Ground Floor

b) 1st Floor

c) 2nd Floor

d) Terrace Floor

Finishing wall surface of wall with cement based wall putty [water based] of approved make and finished smooth and even surface to receive painting including cost etc a) Ground Floor

b) 1st Floor

c) 2nd Floor

d) Terrace Floor

Providing and applying 2 coats with 100% acrylic emulsion paint on New surface including one coat of primer (exterior quality) of approved make & shade by reputed manufacturer to make an even finished surface over a coat of primer with water bound cement primer in all heights with all scaffolding and staging charges including cost , conveyance, taxes of all materials, cost of all labours , T & P, sundries etc. as required for the work complete. a) Ground Floor

b) 1st Floor

c) 2nd Floor

d) Terrace Floor

Supplying and painting of internal walls and ceiling with two or more coats of ACRYLIC emulsion paint on New surface which includes a coat of primer all complete. The shade and brand to be of approved brand & shade over the surfaces including preparation of surface, with cost of all materials, labour, conveyance taxes of all materials,scaffolding etc., as per the direction of the Engineer-in-charge. a) Ground Floor

b) 1st Floor

c) 2nd Floor

d) Terrace Floor

Painting with synthetic enamel paint over a coat of primer of approved colour, shade and brand on New wood work /steel work in two or more coats as required to give an even shade including an under coat of suitable primer of approved brand and manufacturer including cost of all materials with taxes and transportation, loading, unloading, scaffolding, all labour, Labour cess, sundries, T&P, etc. complete as per the direction of the Engineer-in-charge including filling gaps with putties, scrapping, sand papering and cleaning the surface to make free from rusts, dusts and oily substances before applying primer etc. complete. a) Ground floor

b) 1st Floor

c) 2nd Floor

d) Terrace Floor

Supplying, fitting and fixing vitrified tiles in floors of size 600mm x 600mm of approved make confirming to IS: 13755 laid on 20mm thick cement mortar 1:4 (1 cement : 4 sand) and filling joined with white cement of approved quality including cost, conveyance, royalty, taxes of all materials, labour, T&P required for the work complete and as per the direction of the Engineer-in-charge. a) Ground Floor

b)1st Floor

c) 2nd Floor

Supplying, fitting and fixing vitrified tiles in dado, skirting and risers of steps on 12mm thick cement plaster (1:3) joint with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing, cost, conveyance, royalty, taxes of all materials, labour, T&P required for the work complete and as per the direction of the Engineer-in-charge.

b)1st Floor

c) 2nd Floor

Supplying, fitting and fixing granite tiles in floors, treads on steps and landing on 25mm thick bed of cement mortar 1:1 (1 cement: 1 sand) joined with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing, cost, conveyance, royalty, taxes of all materials, labour, T&P required for the work complete and as per the direction of the Engineer-in-charge. a) Ground Floor

b)1st Floor

c) 2nd Floor

Providing and fixing Fiber Reinforced Plastic (FRP) door including fittings and cost , conveyance of all materials, labourers and T&P required for the work etc. all complete as per direction of the E.I.C.

Providing and fixing of 30mm thick WPC door shutter with hinges, tower bolt, handle, stainless steel screws etc. including the cost of all materials, hardware fittings, cost of all labour, conveyance, taxes, loading unloading, T &P etc complete as per the direction of the E.I.C

Providing and fixing of WPC door frames with Rebate cuts and finished cross section size 75mm x 45mm or 90mm x 50mm including cost of all materials , cost of all labour, conveyance, taxes, loading, unloading,, scaffolding, staging, watering and curing, T&P , etc. complete as per direction of the E.I.C.

Supplying, fitting, fixing up window (sliding type) made up aluminum Section 9778 as windows frame, section No. 4095, 4096 and 9777, 3994 as shutter frame with rubber beading including locking arrangement including all fitting including cost of materials all taxes labour, T&P etc. complete as per direction of Engineer-in-charge. Total cost of sliding three track Aluminium window with Mosquito Net .

Supplying, fitting and fixing of M.S grills, grill gates with top and bottom rails, ( as per I.S. specification and as per approved drawings ) in proper position in all floors and at all height including making holes to brick walls/ R.C.C structure/wood work etc. and making good to the damaged walls/ structures with cement concrete (1:2:4) with black hard crusher broken granite stone chips of 12mm to 20mm size ( 20mm size not to exceeds 25% ) including watering and curing including cost, conveyance, loading, unloading, stacking, royalties and taxes of all materials, cost of all Labour, Labour cess ,Sundries, T&P required for the work etc.complete as per the direction of Engineer in charge ( W.I. / M.S. windows grills, grill gates, collapsible gates with top and bottom rails, steel windows, steel doors, steel frames for doors and windows, staircase and parapet railings square bar along with required nos. of nails and screws and other required materials of approved quality and approved size shall be supplied by the contractor at his own cost.)

Supplying, fitting and fixing of Stainless steel of 304 grade in hand railing using 50mm dia of 2mm thick circular pipe with balustrade of size 32mmx32mmx2mm @ 0.90mtr.C/C and stainless square pipe bracing of size 32mmx32mmx2mm in 3 rows in stair case as per approved design and specification ,buffing, polishing etc with cost,conveyance,taxes of all materials, labour, T & P etc. requird for the complete in all respect.

20 mm thick grading plaster in cement mortar (1:4) over roof slab including cost, conveyance, royalty, taxes of all materials & complete work as per specification and direction of Engineer in charge. Terrace Floor

Head Room

INTERNAL PH WORKS Supplying all materials, labour and T&P for fitting and fixing white glazed vitreous china porcelain Indian Pan water closet of size 23" of approved make confirming to IS-2556 and top inlet for sinking into floor with 100mm PVC 'P' trap etc. including supply of necessary cement concrete for fitting the closet etc. complete in all respect in all floors including cost, conveyance and taxes of all materials etc. complete and as per PH specification and direction of Engineer-in-charge.

Supplying all materials, labour and T&P for fitting and fixing white glazed vitreous china porcelain European water closet of approved make confirming to IS-2556 and top inlet for sinking into floor with 100mm PVC 'P' trap etc. including supply of necessary cement concrete for fitting the closet etc. complete in all respect in all floors including cost, conveyance and taxes of all materials etc. complete and as per PH specification and direction of Engineer-in-charge.

Supplying all materials, labour and T&P for fitting and fixing white glazed vitreous china porcelain flat back urinal pan of approved make confirming to IS-2556 and top inlet for sinking into floor with 100mm PVC 'P' trap etc. including supply of necessary cement concrete for fitting the closet etc. complete in all respect in all floors including cost, conveyance and taxes of all materials etc. complete and as per PH specification and direction of Engineer-in-charge including marble partition in between urinals.

Supplying all materials, labour, T&P and fixing standard sized shower (bath shower) of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in- charge.

Supplying all materials, labour and T&P for fitting and fixing white glazed vitreous china porcelain wash basin of size 450mm x 300mm of approved make confirming to IS-2556 and top inlet for sinking into floor with 100mm PVC 'P' trap etc. including supply of necessary cement concrete for fitting the closet etc. complete in all respect in all floors including cost, conveyance and taxes of all materials etc. complete and as per PH specification and direction of Engineer-in- charge.

Supplying all materials, labour, T&P and fixing standard sized CP Bib cock of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge.

Supplying all materials, labour, T&P and fixing standard sized 15mm dia Angular Stop cock of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in- charge.

Supplying all materials, labour, T&P and fixing standard 15mm sized pillar cock of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge.

Supplying all materials, labour, T&P and fixing standard sized Long body 15mm dia CP Bib cock of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in- charge.

Supplying all materials, labour, T&P and fixing standard sized two way CP Bib cock of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in- charge.

Supplying all materials, labour, T&P and fixing standard sized shower (Health Faucet) of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in- charge.

Supplying all materials, labour, T&P and fixing standard sized CP soap Dish holder of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge.

Supplying all materials, labour, T&P and fixing standard sized Chromium Plated brass towel rail complete with Chromium Plated brass brackets fixed to wooden plugs with Chromium Plated brass screws as per specification and direction of the Engineer in charge

Supplying all materials, labour, T&P and and fixtures for providing and fixing of Stainless Steel Sink of size 600 x 50 x 225 of approved make with its components like 40mm CP waste of cat No. ALD 709, 40mm CP waste pipe etc. including all requisite fixing materials complete as per PH specification and direction of the Engineer in charge

Supplying all materials, labour, T&P and fixing standard size sink cock of florentine single lever quaterturn of approved make complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of the Engineer in charge

Providing and fixing circular type stainless steel jalli (grating) with hole for floor /nahani trap etc complete as per PH specification and direction of the engineer in charge

Fixing 600x450mm bevelled edge mirror of superior glass mounted on 6mm thick A.C sheet or plywood sheet and fixed to wooden plugs with Chromium Plated brass screws and washers complete as per specification and direction of the Engineer in charge

Supplying all materials, labour, T&P and fixing standard sized glass-shelf with CP brass brackets and guard rails complete fixed to woden plugs with CP screws as per specification and direction of the Engineer in charge

Supplying all materials, labour, T&P and fittings and fixing of Poly Propelene white double layer water storage Tank of approved make confirming to IS 12701-1996 including cutting holes through the tank and fixing mild steel tubes and fittings and providing extra sockets and jam nuts, fixing ball valve etc including hoisting upto terrace level and placing the tank to the required position etc all complete as per PH specification and direction of Engineer-in-charge. (To provided with brick masonary guard walls which will be paid separately) a) 2000 Ltr.

Supplying all materials, labours, T&P and fitting and fixing of the following size of CPVC pipe confirming to IS 15778 certification mark with socket and screw joints in walls and floors including supplying of required number of fittings of approved make including cutting threads to pipes and pipes to length, including wastage,etc for fitting to the walls with supply of holder ats, clamps, fixing wooden plugs in walls, including testing of pipe line for water tightness complete as per IS specification including cost, conveyance and taxes of all materials all complete as per PH specification and direction of Engineer-in-charge. a) 15 mm dia

b) 20mm dia

c) 25mm dia

d) 32mm dia

e) 40mm dia

f) 50mm dia

Providing all materials, labour, Fitting & fixing of CPVC Ball Valve with CTS socket. Make : Prince) a) 25mm dia

b) 32mm dia

c) 40mm dia

d) 50mm dia

Supplying all materials,labours,T&P for cutting holes through existing brickwork including making good the damages in cement mortar (1:4) for taking GI pipes and fittings/PVC pipes and fittings etc all complete as per PH specification and direction of Engineer-in-charge.

Supplying all materials,labours,T&P for cutting holes through existing RCC floors & roofs including making good the damages for taking GI pipes and fittings/PVC pipes and fittings etc all complete as per PH specification and direction of Engineer-in-charge.

Supplyng all materials, labour, T&P for construction of brick masonary Gulley trap chamber of size300mm x 300mm with CI gulley trap, by Fly ash brick masonry in CM (1:4), CP (1:6) with 150mm x 150mm CI grating including labour and materials for fitting and fixing 100mm dia square mouth CI gully trap with supply of all jointing materials and encasing the gully trap with a block of CC (1:4:8) with 25mm size hard stone metal all complete with providing and fixing of 250mm x 250mm precast RCC cover slab including cost, conveyance, taxes of all materials to site complete as per the PH specification and direction of Engineer-in-charge.

Providing all materials labour, T&P for making grooves in bricks/stone masonary walls vertically or horizontally up to required depth and width in all floor for laying of pipes and fittings up to 50mm dia, testing the joints with required water pressure and making good the damages with cement concrete 1:2:4 with 12mm size h.g.c.b.chips and finished smooth with cement morter (1:4) to original shape including cost of all materials, curing, conveyance of all materials etc. all complete excluding GST as per specification & direction of Engineer-in-charge.

External PH Supplying all materials, labour, T&P, fitting and fixing of 50 mm dia brass / GM full way Valve of approved make including supply of all necessary jointing materials such as red lead point, yarns etc. including cost, conveyance & taxes of all materials, T&P etc. all complete as per P.H. specification and as per the direction of the E.I.C.

Supplying all materials, labours, T&P and fitting and fixing of the following size of CPVC pipe confirming to IS 15778 certification mark with socket and screw joints in walls and floors including supplying of required number of fittings of approved make including cutting threads to pipes and pipes to length, including wastage,etc for fitting to the walls with supply of holder ats, clamps, fixing wooden plugs in walls, including testing of pipe line for water tightness complete as per IS specification including cost, conveyance and taxes of all materials all complete as per PH specification and direction of Engineer-in-charge.

Supplying all materials & labour, T&P and constructing brick masonary chamber for water sluice valve, single air valve & non return valve with Fly ash brick masonary in cement mortar (1:4) as per approved drawing and specification CC (1:4:8) with 4cm size hard granite metal on the bed, 12mm cement plaster (1:6) to inside and cement flush pointing (1:6) to outside surface with 100mm thick RCC M20 cover slab with 20mm hg chips using required quantity of tor steel, centring and shuttering to the slab and dismantling it after 31 days of casting, filling the outside cavity with excavated materials, watering, curing including cost, conveyance, taxes of all materials, labour charges for cutting, bending, binding and tying the grills in proper position etc all complete as per drawing, design and direction of Engineer-in- charge.

Supplying all materials, labour, T&P and fitting and fixing of double air valve of 50mm Dia confirming to the relevant IS specification and dimension including fixing it in position along the pipeline with supply of all required materials such as rubber insertion, nuts & bolts including cost of all materials, taxes, and duties, transportation charges from store to site etc all complete as per the direction of Engineer-in-charge.

SEPTIC TANK Earth work in excavation in Hard rock by mechanical means (Hydraullic excavator)/ manual means overareas (exceeding 30 cm in depth, 1.5 m in width as well as 10sqm on plan) inculding disposal of excavated earth up to 50 m and lift upto 1.5m with all lead and lift including shoring, shuttering & dewatering (if required) with cost of all Labour, Labour cess ,Hire & Running charges of the water pumps, T & P required for the work complete as directed by the Engineer- in- charge. a)Earth work excavation beyond 1.50mtr depth

Extra for every additional lift of 1.5 M or part there of in excavation / banking excavated or stocked materials a) Ordinary soil

Supplying and filling the Foundation & Plinth with clean coarse river sand of approved quality from approved quarry, laying in layers not exceeding 150mm thick, watering and ramming including cost, conveyance, royalty and taxes of all materials, cost of all labour, T&P etc. as required for the work complete as per direction of the Engineer-in-charge.

Providing & laying cement concrete of prop. (1:4:8) in foundation bed and floors using 40mm nominal size down graded, screened, washed hard black crusher broken granite metal of approved quality & from approved quarry including laying in the layers not exceeding 100 mm thick, etc

Providing and laying in position ready mixed M25 grade concrete having compressive strength at 28 days test not lessthan 250kg/sq.cm for reinforced cement concrete work using cement content as per approved design mix etc. Foundation

RCC wall

Cutting,straightening coiled or bent up HYSD/TMT Reinfocement Bars welding or jointing if necessary ,bending, binding,tying the grills as etc

Providing 12mm. thick cement plaster with cement mortar of mix (1:4) in all floors cement and with screened and washed sharp sand for mortar with neat cement punning finished smooth to brick/RCC walls after racking out the joints including watering and curing complete with cost, etc

Providing and laying of P.C.C. of 1:3:6 with 12 mm size hard granite metal in foundation trenches, under floors in line level including curing and ramming etc. all complete as per the direction of the Engineer-in-charge..

Providing & applying cement punning over cement plaster

Back filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5m.

Soak Pit Supplying and filling the Foundation & Plinth with clean coarse river sand of approved quality from approved quarry, laying in layers not exceeding 150mm thick, watering and ramming including cost, conveyance, royalty and taxes of all materials, cost of all labour, T&P etc. as required for the work complete as per direction of the Engineer-in-charge.

Providing & laying cement concrete of prop. (1:4:8) in foundation bed and floors using 40mm nominal size down graded, screened, washed hard black crusher broken granite metal of approved quality & from approved quarry including laying in the layers not exceeding 100 mm thick, etc

Providing and laying in position ready mixed M25 grade concrete having compressive strength at 28 days test not lessthan 250kg/sq.cm for reinforced cement concrete work using cement content as per approved design mix etc Foundation

Providing 12mm. thick cement plaster with cement mortar of mix (1:4) in all floors cement and with screened and washed sharp sand for mortar with neat cement punning finished smooth to brick/RCC walls after racking out the joints including watering and curing complete with cost, etc

Providing and laying of P.C.C. of 1:3:6 with 12 mm size hard granite metal in foundation trenches, under floors in line level including curing and ramming etc. all complete as per the direction of the Engineer-in-charge..

Fly Ash Brick Masonry in cement mortar of mix (1:6) using Fly Ash bricks of size 25c.m x 12 c.m x 8 c.m in Foundation & Plinth having crushing strength not less than 75 kg per square c.m. with cement and screened & washed sharp sand for mortar after immersing the bricks for 6 (Six) hours in water before use in works with all necessary projections, splays cutting, circular moulding, corbelling, chamfering, watering and curing etc. including cost, coveyance,stacking, loading, unloading, royalties , all taxes ,cost of all labour,Labour cess ,scaffolding, sundries and T&P required for the works etc. complete in all respect as directed by the Engineer-in-charge.

Supplying all materials, labour, T&P, fitting and fixing uPVC SWR pipes (Type-B)(Co-moulded Ring type) of approved make confirming to IS-13592/1992with ISI marked, both below & above ground level or fixing on wall surface in all floors including transportation & scaffolding etc. all complete as per specification excluding GST & direction of the Engineer-in-charge. a) Pipe 110mm dia

b)110mmx110mm 'P' Trap (Make:Astral)

c)110mm x 87.5" plain bend

c)110mm x 87.5" Door bend

c)110mm x 45" Plain bend

110mm dia single 'Y' withoutdoor

110mm WC connector/Bend with lip ring

110mm Socket plug

110mm Pushfit coupler

UPVC Tee ( 150x 150x 150) mm

Upvc Elbow

Sinking of 200 mm x150mm size production well through DTH or combination drilling riges in hard rock area with PVC or GI casing pipes. 120mtr depth (1nos)

Supplying, fitting and fixing of Antiskid Ceramic Floor Tiles in flooring using special plain / printed series Ceramic Floor Tile of premium grade ( having minimum thickness 7 mm to 8 mm & size 300 mm x 300 mm OR 600 mm x600 mm, confirming to I.S 13755 of approved quality and shade in floors, treads on steps and landings on 25 m.m thick bed of cement mortar of mix (1:1) laid in proper slope and gradient with screened & washed sharp etc a) Ground Floor

b) 1st Floor

c) 2nd Floor

Supplying, fitting and fixing of ceramic glazed wall Tiles in skirting dado,risers of step and wall using special plain / printed series Ceramic wall Tile of premium grade ( having minimum thickness 6.5 mm to 6.7 mm & size 300 mm x 300 mm OR 600mm x300 mm, a) Ground Floor

b) 1st Floor

c) 2nd Floor

Providing and laying water proofing treatment in sunken portion of WCL bathroom etc. by applying cement slurry mixed with water proofing cement compound consisting of applying (0) First Layer of slurry of cement @ 0.488 Kg/ sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours , b) Second layer of slurry of cement @.242 kg/ sqm mixed with water proofing cement compound @0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours . The rate includes preparation of surface, treatment and sealing of all joints, corner, junctions of pipes and masonry with polymer mixed slurry.

INTERNAL ELECTRIFICATION Recessed wirring to light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLSH/LSZH PVC insulated copper conductor of ISI marked Make- Finolex/Anchor/ Polycab/ HAVELLS/RR KABLE/KEI with 20 mm dia PVC non metallic heavy duty conduit FRLS type ISI marked Make-AKG/BEC/Precision/ Norpack 6A modular type ( flame retradant type) switch ISI marked Make-Schneider (Zencelo) /legrand( Myrius) /Panasonic (vision)/Eq. and ceiling rose ISI marked of modular type G.I box with metallic cover plate (both side) (flame retradant type) Make-Schneider (Zencelo) / legrand( Myrius) / Panasonic (vision)/Eq. of suitable size, modular box with 1.5 sq. Mm FRLSH PVC insulated single core multistandard copper conductor as earth wire including all accessories and connection as per direction of Engineer -in -Charge. Group-A

Group-B

Group-C

Subsequent point of group control

Supplying,fixing of 6A Plug on the separate board with complete fitting by 01 no of 6A switch & socket(modular type)( (anti bactorial & flame retradant type)) with suitable size modular box & cover(anti bactorial & falme retradant type) including supplying of all required accessories of ISI marked as approved as per direction of engg-in-charge..Make-Schneider (Zencelo) / legrand( Myrius) /Panasonic (vision)/Eq. (Maximum 02 nos point in one circuit).

Supplying ,fixing of 6A Plug on the same board in existing switch board with complete fitting by 01 no of 6A switch & socket (modular type)( (flame retradant type)) & other required accessories of ISI marked as approved as per direction of Engg. -in -Charge. Make-Schneider(Zencelo)/ legrand( Myrius) /Panasonic (vision) /Eq. (Maximum 02 nos point in one circuit).

Supplying,fixing of 1x16A Plug on the separate board with complete fitting by 01 no of 16A switch & socket(modular type)( flame retradant type)) with suitable size modular box & cover( falme retradant type) including supplying of all required accessories of ISI marked as approved as per direction of engg-in-charge.. Make-Schneider ( Zencelo ) / legrand ( Myrius) / Panasonic (vision)/Eq. (For equipment power).

Recess wiring for circuit/submain wiring with the following mentioned size PVC FRLSH / LSZH insulated, copper conductor, single core cable Make- Finolex / Anchor / Polycab / HAVELLS / RR KABLE / KEI in recessed PVC conduit Heavy duty FRLS of mentioned size Make-AKG / BEC / Precision/Norpak as required as per direction of Engg.-in-Charge. a) 2 x 2.5mm2 for inverter wiring

b) 2 x 1.5mm2 + 1 x 1.5mm2

c) 2 x 2.5mm2 + 1 x 1.5mm2

d) 2 x 4mm 2 + 1 x 1.5mm2

e) 4 x 6mm2 + 2 x 2.5mm2

f) 4 x 10mm2 + 2 x 4 mm2

MAIN PANEL S/I/T&Commissioning of LT indoor floor mounted cubical type electrical main panel made out by 2mm CRCA steel sheet duly derusted & painted by simens gray powder cote paint is designed as G.A drawing as per direction of Engg.-in-Charge.In commer- 01 number of 100 Amps 4P MCCB,25KA with 100A 4P changeover switch (Icu=100%Ics) with shunt trip.with auxuliary Busbar- 04 numbers of 100Amps Electrolytic copper busbar duly sleeved by color coded PVC sleeve & supported by suitable size DMC insulator Out going- .(i)63A FP MCCB 16KA- 04 Nos. (ii) 63A 4P MCB-03 Nos. (iii) 40A 2P MCB- 03 Nos. Instrument- (i) 06 (03 main +03 DG) numbers phase indicating lamp with HRC fuse.(ii) 01 set of digital type multifunction meter with CT for voltage, current, frequency, PF, THD indication (iii) 01 set of 40KA TYPE2+1 4P SPD along with 63A 4P MCB.Make of switchgear-Legrand / Schneider / Siemens / ABB/ Havells/ C&S/ Hagar / L&T as per the direction of the Engineer-in-charge.

4 Way(8+12) Way TPN MCB DD DB Horizontal Type as per IEC 61439-3 suitable for Flush mounting and Surface mounting with 100A Copper Bus Bar for each phase, with neutral Bus bar, Earth Bar & Cable ties for cable management, prefitted masking sheet, IP43-IK09 with metal door(but with out MCB/ RCCB/ Isolator)(FOR LIGHT,POWER INDOOR,3-PH,POWER LOAD)

Supplying and fixing 6 amps to 32 amps rating, 240 volts, C series, single poles MCB of Make-LEGRAND/ Siemens/ Schneider /Equievalant model of Havells/C& S/ ABB/Hagar/L&T in the existing MCB DB complete with connections as per direction of Engg.-in-Charge.

Supplying and fixing 6-32Amps DP 240 volts, MCB Make-LEGRAND/ Siemens/ Schneider /Equievalant model of Havells/C& S/ ABB/Hagar/L&T in the existing MCB DB complete with connections as per direction of Engg.-in-Charge.

Supplying and fixing 40Amps 4P 415 volts MCB Make-LEGRAND/ Siemens/ Schneider /Equievalant model of Havells/C& S/ ABB/Hagar/L&T in the existing MCB DB in the existing MCB DB complete with connections as per direction of Engg.-in-Charge.

Supplying and fixing 40Amps 4P 415 volts RCCB 30 mA Make-LEGRAND/ Siemens/ Schneider /Equievalant model of Havells/C& S/ ABB/Hagar/L&T in the existing MCB DB complete with connections as per direction of Engg.-in-Charge.

Fitting & Fixtures S/F. of Superior type Call bell with push & flexible cord as per direction of Engg.-in-Charge.

Supplying, installation, testing and commssioning of 1200 mm sweep white/milky colour BLDC ceiling fan with aluminium blades having wattage not more than 28W and air delivery ≥215m3/min Make-Crompton Energion Groove /Havells Efficiencia Neo/Usha Technix ) including wiring the down rod of standard length (upto 30 cm) with 1.5 sq mm PVC insulated, copper conductor, single core cable etc. as required as per direction of Engg.-in-Charge.

S/F of BLDC Fan regulator.Make:Legrand / L&T / Havells / Anchor / Eq as per direction of Engg.-in-Charge.

S/F of 400 mm sweep wall Fan Make:Usha / Almonard / Crompton / Havells / Bajaj / Halonix as per direction of Engg.-in-Charge.

Supplying, installation, of exhaust fan of heavy duty 300 mm sweep (Make- Havells / Crompton / Usha / Orient / Bajaj / Halonix ) of exhaust fan in the existing wall, including fixing & conntection as required as per direction of Engg.-in-Charge.

S/F. of 250mm Sweep Exhaust fans of ISI marked.(Make:-Havells Thrill Air DX / Usha / Crompton / Orient / Bajaj / Halonix/equivalent) as per direction of Engg.-in-Charge.

S/F. of 90Wt. With efficacy of 120lm/W Light emitting diode Street light fittings of Havells/ Crompton/ Bajaj/Philips/Halonix /Panasonic/ Wipro/LT as per direction of Engg.-in-Charge.

S/F. of 20Wt.,100lumens/watt efficacacy, aluminium batten Light emitting diode Tube light fittings of Havells/ Crompton/ Bajaj/Philips/ Halonix /Panasonic/Wipro/LT as per direction of Engg.-in-Charge.

S/F. of 18 Wt.Surface/Recess Mounting LED Down Light of Bajaj/ Havells / Crompton/ Philips/ Panasonic/Wipro/Halonix make as per direction of Engg.-in-Charge.

S/F. of 15 Wt.Surface/Recess Mounting LED Down Light of Bajaj/ Havells / Crompton/ Philips/Panasonic/Wipro/Halonix make as per direction of Engg.-in-Charge.

S/F. of 12 Wt.Surface/Recess Mounting LED Down Light of Bajaj / Havells / Crompton / Philips / Panasonic/ Wipro / Halonix make as per direction of Engg.-in-Charge.

Supply and fixing 3 pin, 5A ceiling rose on the existing junction box/ wooden block including connection etc. as required.

Lightning Protection Supply of 8 mm Aluminum Round Conductor.Tested as per IEC 62561. as per direction of engineer in charge.Make-OBO/Dehn/Cape as per direction of Engg.-in-Charge.

Supply of Roof conductor holder for parapet- Polyamide Conductor holder:With M8 female thread or diameter 7mm, M8 Screw to connect the conductor holder.Weather and temperature resistant from -35 to +90 degree Celsius tested.Conductor holder @ 1 meter distance.Tested as per IEC 62561. as per direction of engineer in charge.Make-OBO/Dehn/Cape

Supply of Polyamide roof cable holder for flat roof: DIN 48829 Form B1. Closed form with bottom. Filling weight 1Kg (frost-resistant concrete). Sleeve from polyethylene, black @ 1 meter distance. Tested as per IEC 62561. Make-OBO/Dehn/Cape

Supply of Connector: For T cross and parallel connectors. Quick installation using hexagonal bolt M10X30 high-grade hot dip galvanised. Tested as per IEC 62561 ( 2nos / expansion piece ).Make - OBO / Dehn / Cape

Supply of 1 mtr vertical air terminal with mounting accessories on the flat surface to meet the requirements of IS/IEC 62305.Tested for Electrical , mechanical and chemical as per IEC 62561. Tested for 100kA lightning current. Make-OBO / Dehn / Cape

Supply of Vertical air terminal with accessories:Providing of Air terminals as per IS-IEC -62305 part-3 Nominal size Ø10/16 mm aluminium rod: 3 Mtr Airterminal: semi-hard (E-AlMgSiO5 corresponds to DIN 48801) Suitable for high wind load. Tested as per IEC 62561. Make-OBO/Dehn/Cape

Supply for Providing of Stand for Fang Fix system 16 kg with base and clamp ,made up of frost resistant concrete and clamp testedupto 100KA lightning current . Make-OBO/Dehn/Cape

Supply for Providing of Stand for Fang Fix system 16 kg made up of frost resistant concrete. Make-OBO/Dehn/Cape

Supply of Test Joint (Folding Clamp) suitable to connect 8mm round conductor and max by 30x3 mm GI strip as specified in drawing and directed by Engineer.Tested for 100kA lightning current. Make-OBO / Dehn / Cape

Supply of IP 66 Poly Propylene Junction Box. Installation at 1Mtr Height For Test Joint .Internal dimensions: 100x100x48 mm Make-OBO/Dehn/Cape

Supply of Galvanised Steel Flat 30X3 mm thickness from earth electrode directly in ground as required. Flat conductor Hot Dipped Galvanized. Tested as per IEC 62561. Make-OBO/Dehn/Cape

Supply for Providing of Cross connector for Flat: Suitable for 30mm Galvanised steel strip. Installed with 4 nos of hexagonal plate. Tested for 100kA lightning current. Make-OBO/Dehn/Cape

Supply of flat conductor holder- Fit: FL 30, With mounting hole 6.2 x 22 mm, With 2 cylinder bolts M6 x 16 and over-piece from hot-dip galvanised steel, Bottom section from polyamide, black. Tested as per IEC 62561. Make-OBO / Dehn / Cape

Supply for Providing of Plastic Corrosion Protection strip: Approx 1.1 mm thick. Width 50mm. Made of petrolatum- coated chemical fibre fabric. Make-OBO/Dehn/Cape

Supply of UL Listed maintenance free ,Low carbon copper coated earth rod of 3 metre electrode having diameter of 17.2mm with copper coating thickness of 250micron tested as per IEC 62561-2 Make-OBO / Dehn / Cape

Supply of universal clamp made of SS to connect rod with flat conductor Make-OBO/Dehn/Cape

Supply of Earth conductivity enhancing mineral compound shall be of 25kg/pit tested as per IEC 62561-7,TCLP tested Make-OBO / Dehn / Cape

Supply of The above arrangements shall be provided with Heavy duty earth champer of 5000kg load bearing capacity to ensure the safety of earthing system Make-OBO/Dehn/Cape

Installation of The above arrangements including all accessories as per Direction of Engg. In charge.

CABLES Providing,fixing and laying of 50 mm dia G.I. pipe (medium class) in ground complete with G.I fitting incl. trenching (75 mm depth) and refilling as per direction of Engg.-in-Charge.

Laying and fixing of one number of PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of size exceeding 25 sq.mm but not exceeding 120 sq.mm direct in ground including excavation, sand cushing, protective covering and refilling the trench etc. as required as per direction of Engg.-in-Charge.

Supplying and making end termination with brass compression gland and aluminum lugs for following size of PVC insulated and PVC sheathed / XLPE aluminum cable of 1.1 KV as required. (3.5C x 35 sq.mm) as per direction of Engg.-in-Charge.

S/F of special earthing complete with 3mtr long 40 m dia G.I pipe , 600x600x3.15mm thick copper plate , charcoal , salt including excavation of earth and filling of loose soil upto ground level including all connection and masonary work as per direction of Engg.-in-Charge.

Supplying and laying 25 mm x 5 mm CU earth strip ISI marked on surface or in recess for connection etc as required.as per direction of Engg.-in-Charge.

Supply and installation of Rubber Mats 8 mm thick as per direction of Engg.-in-Charge.

FIRE EXTINGUISHER Supplying installation testing and commission of ABC type fire extinguishers of 6 Kg capacity confirming to IS:14609 & ABC powder confirming IS:13849 presurized with Nitrozen Gas marked including cost of all materials and labourfor all floors and service building etc. all complete. Make- KANEX/ FIRE SHILD / SAFEX or equivalent.

Supplying, installation, testing and commissioning of CO2 type Fire extinguisher 4.5 kg capacity confirming to IS:2878 made from ISI marked seamless cylinder confirming to IS:7285, fitted with ISI marked controlled valve confirming to IS:3224, high pressure 1 mtr discharge hose and horm complete with initial gas charged with carrying handle and wall mounting bracket for all floors and service building etc. as per direction of the E.I.C. Make- KANEX/ FIRE SHILD / SAFEX or equivalent.

Supplying, installation, testing and commissioning of Mechanical Foam type 9 Liter capacity Fire Extinguisher, ISI marked, IS:10204, containing 540 Ml AFFF liquid ISI Marked , IS: 4989 part II and a Polyurethane coated CO2 Gas Catridge, ISI Marked , IS 4947 complete with gunmetal union cap, nylon hose with plastic foam making branch and wall mounting bracket as per direction of the Engineer-in-charge.

MISCELLANEOUS WORK : Sand Bucket as per IS specification

Buket stand to store 10 Nos. of Buket also having Aluminium sheet above the to prevent the stand from rain/ sunst.

Please Enable Macros to View BoQ information