Construction of Block-cumcircle office building at Kumarkhand block in Madhepura dist

All kinds of soil

Cement mortar 1:6 ( 1 cement: 6 coarse sand)

30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Twin rubber stopper

Fixing with adjustable lugs with split end tail to each jamb

Fixed to openings / wooden frames with rawl plugs screws etc.

With float glass panes of 4.0 mm thickness

With stainless steel cover plate minimum 1.25 mm thickness

Size of Tile 60x60 cm

Size of Tile 600 x 600 mm.

20 to 25 mm thick -

Two or more coats on new work

Two or more coats on new work

Two or more coats on new work

New work ( three or more caots)

3 mm thick

for fixed portion

for shutter of door

with float glass pan 8mm

300 mm dia

150mm nominal size dia

150 mm dia

150 mm dia

Providing and fixing Ball plug / Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS : 2800 (Part I)

Providing and fixing 40 mm. dia. nominal bore G I pipes complete with G.I. fittings of approved brand and manufacture etc. all complete jobs.

15mm dia G.I pipe

20mm dia G.I pipe

25mm dia G.I pipe

32mm dia G.I pipe

15mm dia nominal bore

20mm dia nominal bore

32mm dia nominal bore

40mm dia nominal bore

50mm dia nominal bore

15mm nominal bore

20mm nominal bore

32mm nominal bore

40mm nominal bore

50mm nominal bore

150 mm diameter

15 mm diameter pipe

20 mm diamatre pipe

25 mm diametre pipe

32 mm diametre pipe

40 mm diamatre pipe

50 mm diamatre pipe

15 mm nominal bore

20 mm nominal bore

32 mm nominal bore

40 mm nominal bore

50 mm nominal bore

15 mm nominal bore

15mm nominal bore

15mm nominal bore

Cutting holes up to 15 x 15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) including finishing complete so as to make it leak proof.

White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing 600x120x5 mm glass shelf with edges round off,supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms

For 100 mm dia pipe

Hubless Centrifugally cast (spun) iron pipes epoxy coated inside & outside IS : 15905

Hubless Centrifugally cast (spun) iron pipes epoxy coated inside & outside IS : 15905

White Vitreous china Orissa Pattern W.C pan of size 580x440mm with integral type foot rests.

W.C pan with ISI marked white solid plastic seat and lid.

One urinal basin with 5 litre white P.V.C. automatic flushing cistern.

Range of three urinal basin with 10 litre white P.V.C. automatic flushing cistern.

Range of two squatting plates with 5 litre white P.V.C. automatic flushing cistern.

White Agaria Marble Stone

50 mm dia

150 mm diameter

150mm diameter S.W. pipe

With Common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Screened through sieve of I.S. designation 4.75 mm

Mixing earth and sludge or manure in proportion specified or directed.

Spreading of sludge, dump manutre or/and good earth in required thickness (Cost of sludge, dump manure or/and good earth to be paid separately)

In rows 5 cm apart in either direction.

Holes 1.2 m dia. And 1.2 m deep.

11.1.1/ 7.7 DSR-20 (Horticulture & Landscape)

11.1.2/ 7.24 DSR-20 (Horticulture & Landscape)

11.1.3/ 7.16 DSR-20 (Horticulture & Landscape)

11.2.1/ 8.10 DSR-20 (Horticulture & Landscape)

11.2.2/ 8.33 DSR-20 (Horticulture & Landscape)

11.2.3/ 8.48 DSR-20 (Horticulture & Landscape)

7.0 BCD-SOR-22

150 mm dia

100 mm dia

80 mm dia

50 mm dia

25 mm dia

2.10 BCD-SOR-22

Pipes, cables etc. exceeding 80 mm dia . But not exceeding 300mm dia.

14 BCD-SOR-22

100 mm dia

11 BCD-SOR-22

150 mm dia

100 mm dia

80 mm dia

6.0/ 10 BCD-SOR-22

Single headed Gunmetal

Single headed Stainless Steel

17 BCD-SOR-22

16.2 BCD-SOR-22

19.2/BCD-SOR-22

18.1 BCD-SOR-22

1.0 BCD-SOR-22

3.0 BCD-SOR-22

180 lpm at 70 m Head

4 BCD-SOR-22

450 lpm at 35 m Head

22 BCD-SOR-22

17.2/ E&M DSR-22

Two Loop Panel.

17.1.2/E&M DSR-22

17.2.7/E&M DSR-22

17.2.14/E&M DSR-22

17.2.15/E&M DSR-22

17.5.3.2/E&M DSR-22

21 BCD-SOR-22

Upright Sprinkler

With common burnt clay F.P.S(non modular) bricks of class designation 100 A

With common burnt clay F.P.S (non modular) bricks of class designation 100 A

(a) 80 mm thick c.c. paver block of M-35 grade with approved colour design and pattern.

TOTAL OF SCHEDULED ITEM

TOTAL (A)=

NS/ AP by Circle

One incoming main isolation MCCB TP of Min. 250 Amps. rating.

Fully taped aluminium bus bar of required capacity in a separate bus bar chamber.

Isolation MCCB for each unit of required rating and with fully automatic starter as per requirement with push button and ON/OFF indicating lights for each unit, for following requirements:

One main fire pump of 50 HP.

One jockey pump of 10 HP (Each).

One Diesel Pump Controlling System

Single phasing preventors of suitable rating one for each motor.

One 96mm square panel type Amp. meter reading 0-500 Amp. for main fire pump and sprinkler pump.

One 96mm square panel type Amp. meter reading 0-500 Amp. for each Jockey pumps.

Appropriate etched plastic plate for each starter/switch.

Colour coded internal wiring from incoming main to bus bar, switch gear, starters, meters indicating lamp etc., complete in all respects.

Power cable 3 core 16 Sq.mm

Power cable 3 core 25 Sq.mm

Modular desk based system of ht. 1200 mm. Cube legs are fabricated by Argo Shield & have a rectangular shape. Cube legs are available for work top level 750 mm from base. Wire Management Single Power box with raiser for Manager Modules, Single tables (8+3 Anchor Roma). Soft closing access flap with brush. Metal modesty: Metal modesty is made from 0.8 mm thick CRCA. Metal modesty are mounted on the worktop with the help of the modesty mounting brackets made of 3 mm thick HR Screen: 18mm thk T mold Fabric screen on studs is providing on table top of ht. 450 mm. Worktop: 25mm thk prelaminated partical board with pvc lipping.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The adjustable armrest is designed with the following features · Up-Down adjustment– 6 steps (7.2 ± 0.5cm range) · Armrest top is mounted on Armrest structure made of glass filled Nylon. · Armrest Top is PU moulded over glass filled Nylon insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 113.5-123.5 CM. SEAT HEIGHT (SH): 46.0-56.0 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

SEAT/BACK ASSEMBLY: The seat and back should be made from seasoned wood and plywood. The same should be upholstered with black synthetic leather and polyurethane foam. BACK SIZE: 46.0cm. (W) X 27.0cm. (H) SEAT SIZE: 46.0cm. (W) X 40.0cm. (D) ARMREST TUBE: The armrest tube should be made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 48.0 cm. Height - 87.5cm. Width & Depth of Chair as measured from base - Width-58.0 cm and Depth-56.5 cm.

Providing and placing desk based modular workstation with size 900x600 System ht - 1200 mm. PARTIAL SCREENS: Fabric T- mould, 19mm thk Screen of 450mm ht.,mounted on Studs. CLIP ON SCREEN: Fabric T-mould (19 mm thick) of 450mm ht. Removable screen and to be used as divider screen. It has a die cast fixing clamp to enable mounting of the screens to the worktop, LEGS: Providing metal powder coated Cube leg. Legs are for standard workstation height of 750mm. UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs and legs. Made up of metal powder coated finish and the entire assemply is fixed to the worktop. WIRE MANAGEMENT: For 750 high workstations- For vertical wiremenagement, wire risers with cover are considere. . Access flap will be provided. Switch plate of (8+3 Anchor Roma) module is considered for Power and Data points. WORKSURFACE - Out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1200 mm w x 600 mm d. MODESTY : Metal modesty: Lazer cut perforated Metal modestyMetal and wooden modesty are mounted on the worktop with the help of the modesty mounting brackets, Modesty terminates at 400 mm from ground.

SEAT/BACK ASSEMBLY: The seat and back are made from 1.2 ±0.1cm. thk hot pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric and moulded Polyurethane foam together with seat and back covers. The back foam is designed with contoured lumbar support for extra comfort. * 5102R MIDBACK SIZE: 45.0cm(W) x 53.0cm.(H) * 5103R LOWBACK SIZE: 44.0cm(W) x 47.0cm.(H) * SEAT SIZE: 52.0cm(W) x 48.0cm.(D) 2. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. 3. SEAT/BACK COVERS: The seat and back covers are injection moulded in black Co-polymer Polypropylene. 4. ARMREST ASSEMBLY: The one-piece armrests are made of black integral skin polyurethane reinforced with M.S. insert with 50-70 Shore 'A' hardness. The armrests are scratch and weather resistant. The armrests are fitted to the seat with armrest brackets made of 0.5 ± 0.05 cm. thk. HR steel. PERMANENT CONTACT MECHANISM: The permanent contact mechanism is designed with the following features: 360° revolving type. 14° ±2°maximum back-tilt only. Upright position locking. Tilt tension adjustment. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm. TELESCOPIC BELLOW ASSEMBLY: The bellow is 3 piece telescopic type and injection moulded in black Polypropylene. 8. PEDESTAL ASSEMBLY: The pedestal is fabricated from 0.2 ± 0.02 cm thick HR sheet (IS :DD 1079/HR), powder coated (DFT 40-60 microns) and fitted with an injection molded black Polypropylene hub cap and 5 nos. twin wheel castors. The pedestal is 60.0 ±0.5cm. pitch-centre dia. (70.0 ±1.0 cm. with castors). 9. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in Black Nylon.

Supplying and placing in position office table of the following specifications. 1500W X 600D X 750H Worktop-Made of 25mm Thick Pre-laminated board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Access Flap provided on work surface for wire management. Modesty Panel-Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Legs-Cube legs are fabricated from MS ERW Tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick (as per IS: 7138). At the top surface of leg, support brackets of 3 mm thick HR (as per IS: 2062) are welded for fixing worktop. These are welded together by argo shield welding. This welded structure is coated with 50 micron epoxy polyester coating. At the base, a plastic cap with M8 molded insert is fixed, on to which a straight M8 leveler fitted which allows for adjustment of the height upto 50mm. Cross Members-Cross Members in Unitised T-2 Desk Series are made from 50mm X 25mm X 1.2mm thick ERW tube (as per IS:7138). These are coated with 50 micron epoxy polyester coating. Cross Members are assembled by friction fit PDC joinery and grub screws. There are always two cross members for one table. Access Flap-Soft closing access flap is used in Unitized T-2 Desk Series. Provision for standard size of 8 module electrical (Anchor Roma) is offered. Access flap is made from Aluminum extrusion, PDC parts made from Aluminum Alloy and plastic parts are made from Nylon 6 and wire brush with nylon bristles. Power Box-Power box made with 0.8 mm thick CRCA (IS: 513), with switch plate (8 Module cutout provision for Anchor Roma). This is fixed with worktop along the depth at Access Flap position This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

Providing and placing desk based modular workstation with size 1200x600 System ht - 1200 mm. PARTIAL SCREENS: Fabric T- mould, 19mm thk Screen of 450mm ht.,mounted on Studs. CLIP ON SCREEN: Fabric T-mould (19 mm thick) of 450mm ht. No screen to be used as divider screen. LEGS: Providing metal powder coated Cube leg. Legs are for standard workstation height of 750mm. UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs and legs. Made up of metal powder coated finish and the entire assemply is fixed to the worktop. WIRE MANAGEMENT: For 750 high workstations- For vertical wiremenagement, wire risers with cover are considere. . Access flap will be provided. Switch plate of (8+3 Anchor Roma) module is considered for Power and Data points. WORKSURFACE - Out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1200 mm w x 600 mm d. MODESTY : Metal modesty: Lazer cut perforated Metal modestyMetal and wooden modesty are mounted on the worktop with the help of the modesty mounting brackets, Modesty terminates at 400 mm from ground. Pedestals with legs - Nova pedestal flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. CPU trolley - with castors, KBPT with mousetray - Metal

Providing, supplying and placing of storage unit. Overall size Shall be 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Supplying and placing in position Main table of the following specifications. The Main table shall be of size 1800 Width mm x 900 mm Depth x 750 mm height. Top surface of the table shall made up of MDF (Medium density fibre ) board duly finished with Veneer and final coating of PU. The Main desk should contain in built key board pull out tray for keeping keyboard of computer. The front modesty panel of the table shall be made up of MDF board of size 1640 mm x 600 mm x 16mm which shall also be duly finished with Veener and PU coating. For personal storage one mobile pedestal (3 drawer unit) shall be provided of size 510 mm Width x 635 mm Height and 445 mm Depth. The storage pedestal shall also be made up of MDF duly finished with veener & final coating of PU. The Side shall be of size 1200mm Width x 445mm Depth x 660 mm Height. The side unit shall be made up of MDF board duly finshed with Veneer and final finish by PU Coating. The design of the side unit shall be such that it can be placed on either side of the main table. The side unit shall contain open space for keeping cpu in extreme right side, one closed storage shutter at extreme left end & open space in the middle with one shelf for keeping files. The thickness of the top of the side unit shall be 25mm.

Supplying and placing in position Back unit of the following specifications. The Size of the Back unit shall be 2215mm width x 410 mm Depth x 2000mm height. The back unit shall be made up of MDF board duly finished with veneer & final finish by PU coating. Below storage shall be provided with wooden shutters & the upper left & right side of the back unit shall also be provided with wooden shutters. The middle 3 door shutters should be of glass of minimum 5mm thick for display purpose. The hardness of the PU coating shall be 1.5H

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area.The Recron filling done in seat & back ( Executive chairs only) for extra fluffiness and comfort in chair. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The 3-way adjustable armrest is is made of die-cast aluminium with buffing finish designed with the following features : · Up-Down adjustment–7 steps (7.0 ± 0.5cm range) · It has to & fro movement along with Swivel adjustment. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm. PEDESTAL ASSEMBLY : The pedestal is made of die-cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ± 0.5cm pitch-center dia. (77.0 ± 1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 77.0 CM. DEPTH (D): 77.0 CM. HEIGHT (H): 110.5-120.5 CM. SEAT HEIGHT (SH): 44.5-54.5 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

Providing, supplying and placing of Visitor Chair.CHAIR UPPER STRUCTURE: It is a single shell 1.2 ±0.1cm. thick hot pressed plywood with moulded polyurethane foam on top & backing foam on rear side. It is upholstered with option of knitted & leatherette fabric.The seat has extra thick foam on front edge to give comfort to popliteal area.The foam backing done in back ( Executive chairs only) for extra fluffiness and comfort in chair. 2SEAT & BACK HIGH RESILIENCE (HR) POLYURETHANE FOAM :The HR polyurethane foam for seat and back is moulded with density 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf as per IS:7888 at 25% compression. M.S. VISITOR TUBULAR FRAME (For Thrill Visitore chair): The powder coated (DFT 40-60 micron) tubular frame is cantilever type & made of Ø2.54±0.03 cm x 0.2±0.016 cm thk MS ERW tube. ARMRESTS:The armrest top is moulded from polyurethane(PU) with metal insert and mounted on to a tubular frame. WIDTH (W): 60.5 CM. DEPTH (D): 65.0 CM. HEIGHT (H): 86.5 CM. SEAT HEIGHT (SH): 46.0 CM. This product should be certified by Greenguard

Supplying and placing in position Main table of the following specifications.1650x750x750 Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Softclosing access flap with in-build power box are provided on work surface for wire management. Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Understructure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestal is provided with lock for security This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

. NOTE: HINGE DOOR UNITS (HDU) SPECIFICATIONS FEATURES Width: 450 / 600 / 650 / 750 / 800 / 900 / 950 / 1000/ 1050/ 1200 Height (For Leg Unit) : 750 / 1200 / 1353. UNIT-SIZE Height (For Skirting Unit) : 750 / 119 / 1343. Refer sheet 3 & 4 for all the available options. Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with metal cladding CONSTRUCTION & MATERIAL of 0.8mm thk C.R.C.A (as per IS:513) from outside. Side metal cladding is coated with Epoxy polyster powder of 50+10 microns thickness. In case of 2.5feet Height Storage units,-wooden top is provided which is made of 25mm thick Pre-laminated TOP OPTIONS board whereas 4.0feet and 4.5feet height Storage unitsare provided with 11mm thk bent metal tops made of 0.8mm thk C.R.C.A (as per IS:513). The metal tops are coated with Epoxy polyester powder of 50+10 microns thickness. DOOR & DOOR OPENING Single door opening for 450 & 600w units whereas two door opening for all other width options (i.e; 650 /750/ 800/ 900/ 950/ 1000/ 1050/ 1200W).The doors are made of 18mm thk Pre-laminated boards with decorative laminate on one side and backing laminate on the other side,Uniformly distributed load capacity for each shelf is 40Kg maximum. The skirting units are provided with 150mm high skirting made of 0.8mm thick C.R.C.A (as per IS: 513) and is coated with Epoxy Polyester powder of 50+10 microns thickness. Screw. type adjustible leveler with plastic base provides vertical adjustment for floor unevenness and leveling of units. Back panels are made of 18mm thick Pre-Laminated boards with options of Decorative laminate as well as Fabric finishes. 2,5' height units consist of single back panel whereas 4.0' height and 4,5' height units consist of split back top panel and split back bottom panel separated by an Aluminium extrusion. 3-way nickel plated wooden furniture lock is provided for effective. and positive locking of doors.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The adjustable armrest is designed with the following features · Up-Down adjustment– 6 steps (7.2 ± 0.5cm range) · Armrest top is mounted on Armrest structure made of glass filled Nylon. · Armrest Top is PU moulded over glass filled Nylon insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 113.5-123.5 CM. SEAT HEIGHT (SH): 46.0-56.0 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

Supplying and placing in position Reception table of the following specifications. Work Surface - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Access Flap along with a Gromett is provided on work surface for wire management Wire Management - Power box made with 0.8 mm thick CRCA (IS: 513), with switch plate (8+3 Module cut out provision for Anchor Roma) which is fixed with worktop along the width at Access Flap position. Modesty Panel & Side Skirting - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Understructure - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping TOP shelf - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Hinge Door + Drawer unit - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. **Drawer bottom is made of 5.5thk MDF whiteboard Handle is provided for ease of opening. HDU and Drawer is provided with cam lock for security. Essential Accessories - Wire Riser made of 0.8mm CRCA (IS-513) is provided for proper wire management. Organizer Plate made of 1.2mm CRCA (IS-513) is provided for magnetic sticky notes. Bag Hanger Hook made of 1.2mm CRCA (IS-513) is provided for bag hanging. Length - 2400mm Depth - 1770,870mm Height - 1080mm This product should be certified by GREENGUARD & Indoor Advantage GOLD.

Providing, supplying and placing of Mid Back Chair. SEAT/BACK ASSEMBLY: The seat and back are made up of 1.2 ±0.1cm. thick hot-pressed plywood measured. upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured lumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort to popliteal area. MID BACK SIZE 47.5 cm. (W) x 58.0 cm. (H). SEAT SIZE 47.0 cm. (W) x 48.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS: The one-piece armrests are injection moulded from black Co-polymer Polypropylene. CENTER TILT SYNCHRO MECHANISM : The mechanism is designed with the following features: ·360° revolving type. · Upight position locking · Tilt tension adjustmen. ·Seat/back tilting ratio of1:3. TUBULAR FRAME : The powder coated ( DFT 40-60 microns ) tubular frame is cantilever type & made of Ø 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. ER.W. Tube. PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. TELESCOPIC BELLOW ASSEMBLY : The bellow is 3-piece telescopic type and injection moulded in black Polypropylene. PEDESTAL ASSEMBLY : The pedestal is injection moulded in black 33%glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.3 ±0.5cm. pitch-centre dia. (76.3 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. Overall Dimensions of Chair WIDTH (W): 76.3 CM. DEPTH (D): 76.3 CM. HEIGHT (H): 85.5-97.5 CM. SEAT HEIGHT (SH): 42.5-54.5 CM. This product should be certified by Indoor Advantage GOLD & GREEN PRO.

Providing, supplying and placing of Sofa Overall Size : Width : 175cm Depth : 87cm Height : 76cm Seating Height : 39.5cm STITCHING: THREAD : Poly Proplin. LEATHER/PVC/FABRIC: PVC. Thickness (mm) : 0.9 Weight (GSM) : 575

Providing, supplying and placing of Sofa Overall Size : Width : 134cm Depth : 87cm Height : 76cm Seating Height : 39.5cm STITCHING: THREAD : Poly Proplin. LEATHER/PVC/FABRIC: PVC. Thickness (mm) : 0.9 Weight (GSM) : 575

Providing, supplying and placing of Coffee Table Overall Size : W x D x H - 1000 x 600 x 430mm. 1. Understructure: Legs, top wooden frame & bottom tie members are made out of first quality rubber wood without knots & defects on all faces. Bottom tray is made of 1.2mm thick MS sheet. Metal brackets are used for assembly purpose. 2. Top: 8mm thick toughened glass. 3. Construction: Knock-down assembly. 4. Finish: Bloom_coffee table is in two colour finish option - ÿ Option - 1 : Natural finish ÿ Option - 2 : Walnut finish Wooden members are PU painted with hardness-2H. Metal components are powder coated. Bottom MS metal tray is having floral pattern laser-cut. Top glass is having sand blasted floral pattern on bottom surface. 5. Hardware: Knock-down assembly with high quality standard hardware like screws, metal inserts, wooden dowel, plastic leg bush etc..

Supplying and placing in position Reception table of the following specifications. Work Surface - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Access Flap provided on work surface for wire management. Wire Management - Power box made with 0.8 mm thick CRCA (IS: 513), with switch plate (8+3 Module cut out provision for Anchor Roma). This is fixed with worktop along the width at Access Flap position. Modesty Panel & Side Skirting - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Understructure - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. TOP shelf - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Hinge Door + Drawer unit - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. **Drawer bottom is made of 5.5thk MDF whiteboard Handle is provided for ease of opening. HDU and Drawer is provided with cam lock for security. Essential Accessories - Wire Riser made of 0.8mm CRCA (IS-513) is provided for proper wire management. Organizer Plate made of 1.2mm CRCA (IS-513) is provided for magnetic sticky notes. Bag Hanger Hook made of 1.2mm CRCA (IS-513) is provided for bag hanging. Length - 1500mm Depth - 870mm Height - 1080mm This product should be certified by GREENGUARD & Indoor Advantage GOLD.

Supplying and placing in position Main table of the following specifications.1200x600x750 Work Surface - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Gromet provided on work surface for wire management Modesty Panel - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Under-structure - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Hinge Door Storage - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Handle is provided for ease of opening. Storage is provided with cam lock for security. This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

Supplying and placing in position Main Table & ERU of the following specifications.1650x1650x750 Primary Work Surface:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with0.4mm PVC membrane pressed on to top.Softclosing access flap with in-build power box are provided on work surface for wire management.Secondary Work Surface:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Modesty Panel:Made of 25mm thick MDF one side pre- laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.understructure:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.integrated pedestal:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM.Drawers have a soft closing & anti slam mechanism.Handles are provided for ease of opening.Pedestal is provided with lock for security. This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

Providing, supplying and placing of Mid Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area. The chair seat & back size are FULL BACK SIZE 51.5 cm. (W) x 69.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The adjustable armrest is designed with the following features · Up-Down adjustment– 6 steps (7.2 ± 0.5cm range) · Armrest top is mounted on Armrest structure made of glass filled Nylon. · Armrest Top is PU moulded over glass filled Nylon insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 101.5-111.5 CM. SEAT HEIGHT (SH): 46.0-56.0 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

Supplying and placing in position Main Table & ERU of the following specifications. Its size shall be 1500 Width mm x 750 Depth mm x 740 Height mm .Table top shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick backing laminate (bdl) .Flat edge Duly sealed with 2 mm thick PVC beading.The modesty shall be 18 mm thick plain particle board ( ) PPB Clad with 1.0 mm thick decorative laminate (DL) on both sides. Edge Sealed with 2 mm thick PVC beading. ERU size shall be 1050 Width x 450 Depth x 705 Height. The top of Finesse ERU -3616 LHS shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick Backing Laminate ( BDL).Flat Edge duly sealed with 2 mm thick PVC beading. The Modesty shall be 18 mm thick plain particle board (PPB) Clad with 1.0 mm thick Decorative Laminate (DL) on both sides. Edge sealed with 2 mm thick PVC Beading. Supplying and placing in position Free Standing Pedestal of the following specifications with Overall Dimensions shall be 390mm(W)x440mm(D)x646mm(H). The construction & Material used shall be welded assembled , 0.8 mm thick CRCA for body shell , drawer front & tray , front side stiffener ,rear aide stiffener and 1.2 mm thick CRCA Top stiffener & Bottom stoffener . The drawer fronts shall be metal front straight edge . Locking shall be 10 lever cam lock & Central RH locking with actuator & lock channel mechanism for box-box-file Pedestal . The top panel shall be metal straight edge top . Castor should be swiveling non - lockable castors mounted below the body shell for free standing full height mobile pedestal and M8 Leveling stud for free standing pedestal . The anti-tipping mechanism shall have fifth roller arrangement mounted below file drawer to avoid toppling of unit when file drawer is pulled out . Partition in drawer shall be 1 no. Partition in box drawers with lock mounted . Plastic pencil tray shall be optional accessory . Finish shall be epoxy polyester powder coated to the thickness of 50 microns . Application shall be suitable for pushing below work surface which has got a clear height of 725 mm from below . For drawer pulling side wise tapered recess provided in shell behind drawer fronts . This product should be certified by GREENGUARD.

1800 Head 1800 X 850 X 740, 2 STR MAIN - 1350 X 600 X 740. 2 STR END_LH - 1350 X 600 X 740, 2 STR END_RH - 1350 X 600 X 740 Work Surface-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Plastic ABS access flap is provided for easy access to wires and cables. Work top is available in various shapes. Understructure-It consist of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a knock-down construction. Modesty Panel-Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip provided below work surface to enhance aesthetics. It is made of 0.8mm CRCA as per IS 513,epoxy polyester powder coated (DFT 40-60 microns). Wire Management-An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate is provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component is fitted to pull out audio,video cables onto worktop and connect devices charger to power socket below worktop.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The seat should be made up of 1.2 ±0.1cm. thick hot pressed plywood upholstered with fabric or synthetic leather and moulded Polyurethane Foam. The back should be made up 1.2 ±0.1cm. thick hot pressed plywood and upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. The back ply and foam should be designed with contoured lumber support for comfortable seating posture. BACK SIZE: 48cm.(W) X 76.0cm.(H) SEAT SIZE: 51.0cm.(W) X 48.0cm.(D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam for seat and back should be moulded with density = 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf for 25% compression. ARMRESTS :The armrest top should be made of moulded polyurethane (P.U) and mounted on to a drop lift height adjustable type M.S. tubular armrest support chrome plated. The armrest height should be adjustable up to 6.5±0.5cm. in 5 steps . KNEE TILT SYNCHRO mechanism WITH SEAT DEPTH ADJUSTMENT mechanism: The mechanism should be designed with the following features: • 360° revolving type single point control. • Front pivot for tilt with feet resting on ground ensuring more comfort. • Tilt tension adjustment. • 4-position locking with anti-shock feature. • Seat back tilting ratio of 1:2 • Seat depth adjustment of 6.0 ±0.5cm. can be locked in 6 positions ADJUSTABLE BACKREST: The backrest consshould be ts of a sliding up down mechanism, which can be adjusted in the range of 7.5±0.5cm. and can be locked in 5 positions for correct position of lumber support. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment of 10.0±0.3cm. PEDESTAL ASSEMBLY: The pedestal should be fabricated from 0.2 ± 0.02 cm thick HR sheet . chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. The pedestal should be 66.0±0.5cm. Pitch-center dia. (76.0±1.0 cm with castors). TWIN WHEEL CASTORS The twin wheel castors should be injection moulded in black Nylon. Overall Dimensions of Chair Seat Height - min 47.5 to max 57.5cm. Height - min 103.5 to max 120.5cm. Width & Depth of Chair as measured from pedestal - Width-76.0 cm and Depth-76.0 cm.

Providing, supplying and placing of Mid Back Chair. SEAT/BACK ASSEMBLY: The seat should be made up of 1.2 ±0.1cm. thick hot pressed plywood upholstered with fabric or synthetic leather and moulded Polyurethane Foam. The back should be made up 1.2 ±0.1cm. thick hot pressed plywood and upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. The back ply and foam should be designed with contoured lumber support for comfortable seating posture. BACK SIZE: 48cm.(W) X64.5cm.(H) SEAT SIZE: 51.0cm.(W) X 48.0cm.(D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam for seat and back should be moulded with density = 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf for 25% compression. ARMRESTS :The armrest top should be made of moulded polyurethane (P.U) and mounted on to a drop lift height adjustable type M.S. tubular armrest support chrome plated. The armrest height should be adjustable up to 6.5±0.5cm. in 5 steps . KNEE TILT SYNCHRO mechanism WITH SEAT DEPTH ADJUSTMENT mechanism: The mechanism should be designed with the following features: • 360° revolving type single point control. • Front pivot for tilt with feet resting on ground ensuring more comfort. • Tilt tension adjustment. • 4-position locking with anti-shock feature. • Seat back tilting ratio of 1:2 • Seat depth adjustment of 6.0 ±0.5cm. can be locked in 6 positions ADJUSTABLE BACKREST: The backrest consshould be ts of a sliding up down mechanism, which can be adjusted in the range of 7.5±0.5cm. and can be locked in 5 positions for correct position of lumber support. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment of 10.0 ±0.3cm. PEDESTAL ASSEMBLY: The pedestal should be fabricated from 0.2 ± 0.02 cm thick HR sheet ( should be : DD 1079 / HR skin pass ), chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. The pedestal should be 66.0±0.5cm. Pitch-center dia. (76.0±1.0 cm with castors). TWIN WHEEL CASTORS The twin wheel castors should be injection moulded in black Nylon. Overall Dimensions of Chair Seat Height - min 47.5 to max 57.5cm. Height - min 93.4 to max 110.4cm. Width & Depth of Chair as measured from pedestal - Width-76.0 cm and Depth-76.0 cm.

Providing, supplying and placing of Visitor Chair. SEAT/BACK ASSEMBLY: The seat should be made up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with fabric or synthetic leather and moulded Polyurethane Foam. The back should be made up 1.2 ±0.1cm. thick hot pressed plywood upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. The back ply and foam should be designed with contoured lumber support for comfortable seating posture. MID BACK SIZE: 48.0cm.(W) X 64.5cm.(H) SEAT SIZE: 51.0cm.(W) X 48.0cm.(D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam for seat and back should be moulded with density = 45±2 kg/m³ and Hardness load 16 ± 2 kgf for 25% compression. ARMRESTS:The armrest top should be made of moulded polyurethane (P.U) and mounted on to a fixed type tubular armrest support which should be chrome plated Finish. FIXED BACKREST: The backrest consshould be ts of a fixed type mechanism i.e. no back up/down adjustment. FIXED SPINE : The seat and backare arrested together withfixed type spine i.e no backup/down adjustment ;made of 0.8 ± 0.05cm thk HR steel ans id back power-coated (DFT 40-60 micros). TUBULAR VISITOR FRAME :The tubular frame is cantilever structure & made of Dia 2.54 ± 0.03cm. X 0.2±0.016cm.thk . M.S. E.R.W. tube with a M.S. Spine mounting bracket welded to it. Back spine is fitted to the assembly. The frame finish is Nickel Chrome plated (15-20 microns). Overall Dimensions of Chair Seat Height - 47.7cm. Height - 93.0cm. Width & Depth of Chair as measured from pedestal - Width-66.5 cm and Depth-61.6 cm.

Supplying and placing in position conference table of the following specifications. 2 STR MAIN - 1350 X 600 X 740. Work Surface-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Plastic ABS access flap is provided for easy access to wires and cables. Work top is available in various shapes. Understructure-It consist of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a knock-down construction. Modesty Panel-Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip provided below work surface to enhance aesthetics. It is made of 0.8mm CRCA as per IS 513,epoxy polyester powder coated (DFT 40-60 microns). Wire Management-An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate is provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component is fitted to pull out audio,video cables onto worktop and connect devices charger to power socket below worktop. This product should be certified by GREENGUARD, Indoor Advantage GOLD, GRIHA & SVAGRIHA & GREEN PRO.

Providing, supplying and placing of classroom chair with desklet. SEAT / BACK: The seat sub-assembly should be made up of 1.2±0.1cm thk Plywood upholstered with moulded foam and polyester fabric and covered with an injection-moulded polypropylene outer cover. The seat can tip-up when not in use and thshould be feature can be used while stacking the chairs horizontally The back sub-assembly should be made up of injection-moulded polypropylene inner upholstered with moulded foam and polyester fabric and covered with an injection-moulded polypropylene outer cover. The contoured back with width extension at the bottom should be a should be designed to give comfort to lower back. The back flexing features allows the back to tilt by 9c±2' to aid the user in adopting a comfortable reclining posture. Both these sub-assemblies should be fixed to the tubular structure, BACK SIZE: 45.2cm (W) X 44.6cm (H) SEAT SIZE: 47.0cm (W) X 50.0cm (D) TUBULAR FRAME STRUCTURE: The powder-coated 4 leg structure should be made of 2.2 ±0.03cm dia x 0.25 ±0.02cm thk M.S. E.R.W. Tube front and rear leg welded along with connecting tube made of 1.9 ±-0.02cm dia x 0.2 ±0.016cm thk M.S. E.R.W. Tube to form the tubular frame assembly. The legs should be provided with injection-moulded adopter bush in black Nylon and brake-loaded castors enabling easy maneuvering while not in use and stable sitting while in use_ The chairs can be stacked horizontally when not in use_ POLYURETHANE FOAM: The Polyurethane foam should be moulded with density = 70.0 ±8.0 kg/m3 and Hardness = 12 ±2 for Seat & 16 ±2 for back at 25% compression. ARMRESTS: The armrest structure should be made up of 2.2 ±0.03crn dia x 0.25 ±0.02cm thk M.S. E R.W. Tube welded to the Tubular Frame structure and having a scratch-resistant tant ABS Arm top. FULL DESKLET: The Full Desklet assembly should be Flip-up type and should be made up of extension tube of 1.9 ±0.02em dia x 0_2 ±0.016cm thk PAS. E.R.W. Tube and a support tube on L.H. side of 1.6 ±0.02cm dia x 0.2 ±0.016cm thk M.S. E.R.W. Tube on which an scratch resistant tant ABS desklet top should be fixed and covered on bottom side with a bottom cover. BRAKE-LOADED CASTORS : The brake-loaded castors should be assembled to the chair legs, to give a free movement for maneuvering the chair when not in use and it will brake the movement when load should be applied (while in use) to give a stable feel. The twin wheel castors should be injection molded in black Polypropylene. Overall Dimensions of Chair Seat Height - 47.5 cm. Height - 89.0cm. Width & Depth of Chair as measured from base - Width-66.5cm and Depth-84.0 cm. This product should be certified by Indoor Advantage GOLD & GREEN PRO.

SEAT/BACK ASSEMBLY: The seat and back are made from 1.2 ±0.1cm. thk hot pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric and moulded Polyurethane foam together with seat and back covers. The back foam is designed with contoured lumbar support for extra comfort. * 5102R MIDBACK SIZE: 45.0cm(W) x 53.0cm.(H) * 5103R LOWBACK SIZE: 44.0cm(W) x 47.0cm.(H) * SEAT SIZE: 52.0cm(W) x 48.0cm.(D) 2. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. 3. SEAT/BACK COVERS: The seat and back covers are injection moulded in black Co-polymer Polypropylene. 4. ARMREST ASSEMBLY: The one-piece armrests are made of black integral skin polyurethane reinforced with M.S. insert with 50-70 Shore 'A' hardness. The armrests are scratch and weather resistant. The armrests are fitted to the seat with armrest brackets made of 0.5 ± 0.05 cm. thk. HR steel. PERMANENT CONTACT MECHANISM: The permanent contact mechanism is designed with the following features: 360° revolving type. 14° ±2°maximum back-tilt only. Upright position locking. Tilt tension adjustment. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm. TELESCOPIC BELLOW ASSEMBLY: The bellow is 3 piece telescopic type and injection moulded in black Polypropylene. 8. PEDESTAL ASSEMBLY: The pedestal is fabricated from 0.2 ± 0.02 cm thick HR sheet (IS :DD 1079/HR), powder coated (DFT 40-60 microns) and fitted with an injection molded black Polypropylene hub cap and 5 nos. twin wheel castors. The pedestal is 60.0 ±0.5cm. pitch-centre dia. (70.0 ±1.0 cm. with castors). 9. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in Black Nylon.

SEAT/BACK ASSEMBLY: The seat and back are made from 1.2 ±0.1cm. thk hot pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric and moulded Polyurethane foam together with seat and back covers. The back foam is designed with contoured lumbar support for extra comfort. * 5102R MIDBACK SIZE: 45.0cm(W) x 53.0cm.(H) * 5103R LOWBACK SIZE: 44.0cm(W) x 47.0cm.(H) * SEAT SIZE: 52.0cm(W) x 48.0cm.(D) 2. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. 3. SEAT/BACK COVERS: The seat and back covers are injection moulded in black Co-polymer Polypropylene. 4. ARMREST ASSEMBLY: The one-piece armrests are made of black integral skin polyurethane reinforced with M.S. insert with 50-70 Shore 'A' hardness. The armrests are scratch and weather resistant. The armrests are fitted to the seat with armrest brackets made of 0.5 ± 0.05 cm. thk. HR steel. PERMANENT CONTACT MECHANISM: The permanent contact mechanism is designed with the following features: 360° revolving type. 14° ±2°maximum back-tilt only. Upright position locking. Tilt tension adjustment. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm. TELESCOPIC BELLOW ASSEMBLY: The bellow is 3 piece telescopic type and injection moulded in black Polypropylene. 8. PEDESTAL ASSEMBLY: The pedestal is fabricated from 0.2 ± 0.02 cm thick HR sheet (IS :DD 1079/HR), powder coated (DFT 40-60 microns) and fitted with an injection molded black Polypropylene hub cap and 5 nos. twin wheel castors. The pedestal is 60.0 ±0.5cm. pitch-centre dia. (70.0 ±1.0 cm. with castors). 9. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in Black Nylon.

Providing and placing desk based modular workstation with size 900x600 System ht - 1200 mm. PARTIAL SCREENS: Fabric T- mould, 19mm thk Screen of 450mm ht.,mounted on Studs. CLIP ON SCREEN: Fabric T-mould (19 mm thick) of 450mm ht. Removable screen and to be used as divider screen. It has a die cast fixing clamp to enable mounting of the screens to the worktop, LEGS: Providing metal powder coated Cube leg. Legs are for standard workstation height of 750mm. UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs and legs. Made up of metal powder coated finish and the entire assemply is fixed to the worktop. WIRE MANAGEMENT: For 750 high workstations- For vertical wiremenagement, wire risers with cover are considere. . Access flap will be provided. Switch plate of (8+3 Anchor Roma) module is considered for Power and Data points. WORKSURFACE - Out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 900 mm w x 600 mm d. MODESTY : Metal modesty: Lazer cut perforated Metal modestyMetal and wooden modesty are mounted on the worktop with the help of the modesty mounting brackets, Modesty terminates at 400 mm from ground. CPU trolley - with castors, KBPT with mousetray - Metal

Providing and placing desk based modular workstation with size 900x600 System ht - 1200 mm. PARTIAL SCREENS: Fabric T- mould, 19mm thk Screen of 450mm ht.,mounted on Studs. CLIP ON SCREEN: Fabric T-mould (19 mm thick) of 450mm ht. Removable screen and to be used as divider screen. It has a die cast fixing clamp to enable mounting of the screens to the worktop, LEGS: Providing metal powder coated Cube leg. Legs are for standard workstation height of 750mm. UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs and legs. Made up of metal powder coated finish and the entire assemply is fixed to the worktop. WIRE MANAGEMENT: For 750 high workstations- For vertical wiremenagement, wire risers with cover are considere. . Access flap will be provided. Switch plate of (8+3 Anchor Roma) module is considered for Power and Data points. WORKSURFACE - Out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 900 mm w x 600 mm d. MODESTY : Metal modesty: Lazer cut perforated Metal modestyMetal and wooden modesty are mounted on the worktop with the help of the modesty mounting brackets, Modesty terminates at 400 mm from ground. CPU trolley - with castors, KBPT with mousetray - Metal

Group C

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire (For circuit & street light)

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire (For Computer Terminal)

2 X 4 sq. mm + 1 X 4 sq. mm earth wire(For AC)

4 X 6 sq. mm + 1 X 6 sq. mm earth wire(For LDB & CDB)

4 X 10 sq. mm + 1 X 6 sq. mm earth wire(For PDB)

1 or 2 module (75mm X 75mm)

8 way, Double door (for Building street light)

MAIN PANEL

400 A, 50 KA, FPMCCB

125 A, 36 KA, FPMCCB

160 A, 36 KA, FPMCCB

100 A, 30 KA, FPMCCB

6 A to 32 A, double pole

40 A to 63 A, four pole

4 X 16 sq. mm

4 X 25 sq. mm

Safety Accessories and Misc.

EARTHING

Single arm, 1000 mm

For 6/7 metre pole (500mm X 500mm X 1400mm)

10 sq.mm, 2 core

Upto 35 sq. mm

2 x 1.5 sq. mm

Supply, Installation, testing & commissioning 200 KVA, 11 K V / 433 V, 50 Hz, 3 phase Delta / Star connected, copper wound ONAN Transformer with Dyn-11 vector group suitable for out-door, floor mounting. The transformer shall have OFF Load taps in steps of +/- 2.5 % and +/-5 %, complete with first fill of oil and shall conform to I S : 2026 - 2011 & IS : 1180 (Level-2) : 2014 (latest edition). H. T. & L. T. sides of the transformer shall be suitable for cable termination box / Busduct Termination box complete with cable end-boxes as follows: Make:-kotsons/Powerstar /kirloskar/crompton HT SIDE: 11 KV ,3C X120MM XLPE CABLE ,LT SIDE:,2 X 3.5 X185 Sq. mm. XLPE CABLE Transformer shall have provided with winding over temperature indication and trip devices.

50 Sq.mm, 3 Core

Upto 120 sq. mm

35 sq.mm, 3.5 core (For External Light feeder Pillar)

95 sq.mm, 3.5 core (For Generator Line)

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

3C X 70 Sq. mm

3.5 X 185 Sq. mm.

3.5 X 95 Sq. mm.

3.5 X 35 Sq. mm.

63 mm dia (OD-63 mm & ID-51 mm nominal)

90 mm dia (OD-90 mm & ID-76 mm nominal)

120 mm dia (OD-12 mm & ID-103 mm nominal)

1 run of cable

1 run of cable

Total

ELECTRICAL LIFT- 8 PASSENGER (G + 2) MRL LIFT

Supply, Installation, Testing and Commissioning and final testing of automatic lift complete in the shaft well and pit already constructed as per CPWD Specification including automatic rescue device (ARD), all standard equipments, accessories and control equipments as per manufacture's design and as per CPWD specification (Part-III LIFTS) on turnkey basis, conforming to NBC/Statutory norms and fulfilling following requirements. (i) Type: Passenger lift. (ii) Load: As specified. (iii) Speed: 1.00 metre/sec.

(vii) Total rise: About 3 mtrs. (approx) between two stops. (viii) Landings: All floors on same side. (ix) Floor served: As specified. (x) Signals : Digital car position indicator, car travel direction indicator inside car & at all landings, voice annunciator with suitable music shall be provided in the lift car. (xi) Shaft size: As per manufacturer's design and as per CPWD specification (Part III LIFTS), Shaft to be constructed separately.

(xii) Guide rail: As per manufacturer's specification. (xiii) Lift & Car size: As per manufacturer's design and as per CPWD specification (Part III LIFTS). (xiv) Car Entrance: As per manufacturer's design and as per CPWD specification (Part III LIFTS). (xv) Landing Entrance: As per manufacturer's design and as per CPWD specification (Part III LIFTS). (xvi) Car door: S.S. (Stainless steel) hairline finish centre opening door . (xvii) Landing door: S.S. (Stainless steel) hairline finish centre/telescopic opening door . (xviii) Door operation: Automatic electric power operated door, full height infrared curtain with multiple criss/cross light beams. (xix) Car interior: S.S. (Stainless steel) panel with hair line finish on all sides. (xx) Car floor: Anti skid PVC flooring on heavy duty MS (mild steel) platform. (xxi) Car ceiling & lighting: S.S. (Stainless steel) finish with aesthetic appearance with LED Ceiling lights. (xxii) Car ventilation: Pressure fan/blower fan (car fan with automatic sleep timer shall be provided). (xxiii) Emergency lighting in car: Battery operated emergency lighting in the lift car. (xxiv) Intercom system: Battery operated intercom system in lift car, machine room and ground floor/control room. (xxv) Emergency alarm: Battery operated alarm bell system in lift car & control room/ground floor. (xxvi) Position of machine room: MRL (xxvii) Electric power supply: AC 415V, 3 Phases 50 Hz & AC 230 V1 Phase 50 Hz terminated in machine room.

(xxvi) Position of machine room: MRL (xxvii) Electric power supply: AC 415V, 3 Phases 50 Hz & AC 230 V1 Phase 50 Hz terminated in machine room. (xxviii) Fire man switch: Fire man switch at machine room/terminal landing. (xxix) All car panel buttons and all floor switches must be with braille language as per lift act. (xxx) Audio visual indication in the lift car showing overloading shall be provided such that doors keep open till excess load is removed. (xxxi) Spring buffer/hydraulic buffer shall be provided. (xxxii) Mechnical over speed governor, door key holes in the floor doors shall be provided. (xxxiii) Lift machine hoisting arrangement in the lift machine room and monkey ladder for lift pit should be provided by the lift agency, along with the other steel structure works, foundations for the machines etc. (xxxiv) In the hoist way fascia plate shall be provided. (xxxv) Permanent wiring in lift machine room and lift well with proper no. of light points, with fixtures, exhaust fan, plug points and 3 phase 440V power supply shall be made in lift shaft by the department, machine room or at desired level. (xxxvi) Car top safety barricade shall be provided. (xxxvii) ARD (automatic rescue device): Solit state inbuilt automatic rescue device (ARD) automatically rescues passengers trapped in the lift car in between floors in the event of power failure. Automatic operation and immediate action in the event of mains failure, capable of moving the lift to the nearest landing, opens the automatic door of the lift car and floor. Sealed maintenance free battery backup with automatic charging unit and auto changeover device on mains failure. Make: OTIS/KONE/SCHINDLER/MITSHUBISHITHYSSENKRUP (With 3 year free maintanance in DLP period)

8 Passenger, (544 KG) (G+2) MRL LIFT

100 amps, TP & N

light point- Group - B

35 sq. mm, 3.5 core main point to lift m/s

Upto 35 sq. mm (Clamped with 1 mm thick saddle)

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

4 X 10 sq mm + 1 X 10 sq mm

6 A to 32 A, Single pole

40 A to 63 A, TP

Particulars

Buildings Works (Civil + PHE + Electrical )

Main Block Office Building

Block Office Building (G+2)

Particulars

Development of Site & Bulk Services (Civil + PHE)

Internal Campus Road & Parking 4.5 m wide - 95 mtr., 3.0 m pathway / Driveway wide : 45 mtr. Parking = 227 sqm

Site Development & Campus Filling

External PHE Works (Water supply, Storm water Drainage, Sewerage pipe line + Tube well + Septic tank & Drain)

boundry wall

Under Ground Water Tank - (70 KL Capacity)

Pumps, Water Treatmnet & Allied Equipment

Recharge pit - 2 Nos.

Desilting Chamber - 2 Nos.

Landscape & Horticulture works

Particulars

Interior & Furnishing works in Block office

Fire fighting works

Add Extra GST @ 5.36% on BCD SOR -2022 Items

Contingency

Architects & Consultants Fees

Original works Site Development & Bulk Services including External Electrical @ 2.85%

Repeat works Block Buildings including Internal Electrical fire fighting works and Interior & Furnishing works Repeat Fee @ 0.997% (35% of 2.85%)

BLDG SUB DIV-1

katihar

Description of Work

Earth Work

Earth work in excavation over areas (exceeding 30 cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50 m and lift upto 1.5 m; disposal earth to be levelled and neatly dressed.

All kinds of soil

Extra for every additional lift of 1.5 m or part thereof in

All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth : consolidating each deposited layer by ramming and watering lead.

Supplying and filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete.

Concrete Work

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level.

1:3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

Extra for providing and mixing water proofing material in cement concrete work in the proportion recommended by the manufacturers.

Reinforced Cement Concrete Works

Centring and shuttering including strutting, propping etc. and removal of form for :

Foundations, footings, bases of columns, etc., for mass concrete.

Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Post and struts

Stairs, (excluding landings) except spiral staircases.

Vertical and Horizontal fins individually or forming box louvers band, facias ane eaves boards.

Wheather shade, Chajja, corbels etc., including edges.

Edges of slabs and breaks in floors and walls :

Under 20 cm wide

Extra for shuttering in circular work (20% of respective centring and shuttering items)

Extra for additional height in centring, shuttering where ever required with adequate bracing, propping etc, including cost of de-shutering and de centring at all levels over a height of 3.5 m, for every additional height of 1 meter of part thereof (plan area to be measured)

Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

Reinforcement for RCC work including straightening. Cutting, bending, placing in position and binding all complete.

TMT-500- 8mm dia .

TMT-500-10 mm dia.

TMT-500-12 mm dia

TMT-500-16 mm dia.

TMT-500-20 mm dia.

TMT-500-25 mm dia

TMT-500-32 mm dia

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All work upto plinth level

Concrete of M-25 grade with minimum cement content of 330 kg/cum

All work above Plinth level upto floor V Level.

Concrete of M-25 grade with minimum cement content of 330 kg/cum

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring,shuttering,finishing and reinforcement-All work puto plinth level

1:2:4 (1 cement:2 coarse sand:4 graded stone aggregate 20 rrm nominal size)

Brick Work

Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in :

Cement mortar 1:6 (1 cement: 6 coarse sand ) - 250 mm th Brick work

Half brick Masonary Cement mortar 1.:4 (1 cement: 4 coarse sand ) - 125 mm th Brick work

Extra tor Brick work in superstructure above plinth level upto floor V cum

250 mm th Brick work in C.M (1:6)

125 mm th Brick work in C.M (1:4)

Wood Work

Providing and fixing flush door shutters conforming to IS : 2202 (Part-I) non-decorative type.core of block board construction with frame of 1st class tiard wood and well mathched commercial 3 ply veneering wiih vertical grains or cross bands and face veneers on both faces of shutters.

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing aluminium sliding door bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete:

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ), transparent or dyed to required colour or shade, with necessary screws etc. complete:

Providing and fixing aluminium pull bolt lock, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour and shade, with necessary screws bolts, nut and washers etc. complete.

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Twin rubber stopper

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of shutters (Over all area of door shutter to be measured).

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete:

2nd class teak wood

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing aluminium casement stays, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Providing and fixing 18 mm thick, 150 mm wide pelmet of flat pressed 3 layer or graded wood particle board medium density grade I, IS : 3087 marked, including top cover of 6 mm commercial ply wood conforming to IS: 303 BWR grade, nickel plated M.S. pipe 20 mmdia ( heavy type ) curtain rod with nickel plated brackets, including fixing with 25x3 mm M.S. flat 10 cm long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm on both inner side of pelmet and rawl plugs 75 mm long etc. all complete.

Providing and fixing teak wood lipping of size 25x3 mm in pelmet.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

1.0 mm thick

Providing and fixing PVC rigid foam sheet 1 mm thick on existing door shutters (bathroom and W.C.doors) using synthetic rubber based adhesive.

Providing and fixing oxidised M.S. double acting spring hinges with necessary screws etc. complete.

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter . The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer - incharge . (Cost of SS ball bearing hinges is excluded).

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/m³ and fixing with necessary stainless steel ball bearing hinges of size 100 x 89 x 3 mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge (panelling to be paid for seperately).

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per direction of Engineer-in- charge. The glass shall be clear, toughened, interlayered, non-wired fire resistant having 11 mm thickness of approved brand with 120 minutes of fire resistance both integrity & radiation control (EW120) and minimum 15 min of insulation (EI15) and having a sound reduction of ?37dB and LT of 86%. Glass shall be compliant to class 2(B)2 category of Impact Resistance as per EN 12600. The glass should be manufactured in UL & TUV audited Facility and including UL-EU Certification.The maximum glazing size cannot be more than 1100 mm x 2200 mm (w x h) or 2.42 sq mts in total area. The test report for the complete system (Glazed Door or Partition) will be considered valid only if it contains the stamp and signature of the authorized signatory from the glass manufacturer. (Actual glass size is to be measured at site for payments).

Steel Work

Providing and fixing pressed steel door frame confirming IS code 351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25 mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-Charge.

Profile C

Fixing with adjustable lugs with split end tail to each jamb

Providing and fixing circular / hexagonal cast iron or M.S. sheet box for ceiling fan clamp 140 mm internal dia 73 mm height, 5 mm thick rim bottom and top lid , 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one lock at the comers. Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Steel work welded in built up section/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required

In gratings, frames, guard bar, ladders, railings.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Fixed to openings / wooden frames with rawl plugs screws etc.

Providing and fixing hand rail by welding etc. to steel ladder railings & staircases railing including applying a priming coat of approved steel primer

MS tube (medium) 40 mm nominal dia

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size with top and bottom rail of T-iron 40x40x6 mm with 40 mm dia steel pulleys complete with bots. Nuts locking arrangement stoppers handles including applying a priming coat of approved steel primer

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.).

Aluminium Works Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / neling,C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion

Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item)

With float glass panes of 4.0 mm thickness

With float glass panes of 5.50 mm thickness

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors,embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.

With stainless steel cover plate minimum 1.25 mm thickness

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings, the aluminium quality as per grade 6063 T5 or T6 as per BS 1474, including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-charge. (The item includes cost of fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account)

Designing, fabricating , testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the buildings for all heights and all levels,including

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc.

Flooring Works

Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering taxes, royalty all complete as per building specification and direction of E/I.

Providing and laying polished Granite stone flooring in required design and patterns , in linear as well as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average ) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slury and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer -in-charge.

Polished Granite stone slab of all colour and texture except Black, Cherry/ Ruby Red

Stone tile (polished) work for wall lining over 12 thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and cement slurry @ 3.3 kg / sqm including pointing in white cement complete

Granite of any colour and shade

Providing and laying vitrifed floor tiles in different sizes {thickness to be specified by the manufactruer) with water absorption's less than 0.08 % and conforming to IS : 15622 of approved make in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand ) including grouting the joint with white cement and matching pigments etc., complete.

Size of Tile 60x60 cm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.

Size of Tile 600 x 600 mm.

Providing and laying Vitrified in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.3 kg / sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with notch towel, piler, wedge, clips of required thickness, leveling sysem and rubber mallet for placing the tiles gently and easily

Glazed Vitrified tiles Matt / Antiskid finish of size

Size ot tile 600 x 600 mm

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer -in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Motar 1:3 (1cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of 1:1:1 (1 lime : 1 surkhi: 1 coarse sand ) /1:4 (1 cement : 4 coarse sand)

20 to 25 mm thick -

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Marble stone flooring with 18 mm thick marble stone (sample of marble shall be approved by Engineer-in-charge) over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing complete with :

Raj Nagar Plain white marble 18mm thick above 0.20 sqm upto 0.50 sqm

Extra for Kota stone / sand stone in treads of steps and risers using single up to 1.05 metre.length

Extra for pre finished nosing in treads of steps of Kota stone / sand stone slab.

Extra for making chequers of approved pattern on cement concrete floors, steps, landing, pavements etc.

Providing edge moulding to 18 mm thick marble stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in Charge

Granite work

Plaster & Finishing Works

12 mm cement plaster of mix

1:6 (1 cement : 6 coarse sand)

18 mm cement plaster in two coat under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand finished rough with sponge.

6 mm cement plaster to ceiling of mix.

1:4 (1 cement : 4 coarse sand)

Applying one coat of cement primer of approved brand and manufacture on wall surface :

Distemper Primer

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:

Two or more coats on new work

Distempering with 1st quality washable distemper (ready made) of approved manufacture and of required shade and colour complete. As per manufacture's specifications.

Two or more coats on new work

Applying priming coat:

With ready mixed pink or grey primer of approved brand and manufacture on woodwork (hard and soft wood)

With ready mixed red oxide zinc chromate yellow primer of approved brand and manufacture on steel galvanized iron/steel works

Painting with synthetic enamel paint of approved brand and manufacture to give an even shed.

Two or more coats on new work

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Forming groove of uniform size from 12 x 12 mm and upto 25 x 15 mm in plastered surface as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specifications and direction of the Engineer-in-charge.

Neat Cement punning

Stone work (machine cut edge) for wall lining etc. (veneer work) over 12 mm thick bed of cement lime mortar 1:1:6 (1cement : 1 lime putty : 6 fine sand) including pointing in white cement mortar 1:2 (1 white cement: 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing by means of cramps which shall be paid for seperately)

Red sand stone-exposed face fine dressed with rough backing

Providing and fixing gun metal cramps of required shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 fine sand) including making the necessary chases.

25 x 6 mm - 30 cm long

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part there of

Extra for plastering :

Spherical ceiling

Finishing walls with Premium Acrylic smooth exterior paint with silicone additives of required shade.

New work (Two or more coats applied @ 1.43 ltr / 10 sqm. Over and including base coat of water proofing cement paint applied @ 2.20 kg / 10 sqm).

Finishing walls with textured exterior of required shade :

New work (Two or more coats applied @ 3.28 ltr/ 10 sqm) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm

Water Proofing Treatment Works :

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed protions of W.C. kitchen and the like consisting of :

1st course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.

IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.

IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg per sqm of area.

IVth course of 400 micron thick PVC sheet (overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm

Providing and Laying APP (Atactic Polypropylene polymer) modified prefabricated five layer 3 mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre /sqm by the same membrane manufacture of density at 250 C, 0.87-0.89 kg / litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc, and preparing the surface complete. The Vital physical and chemical parameters of the membrane shall be as under : Joint strength in logitudinal and transverse direction at 230 C as 650/ 450N / 5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 1500C. Cold flexibility shall be upto -20C when tested in accordance with ASTM, D-5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane :

3 mm thick

Extra for covering top of membrane with Geotextile, 120 gsm non woven, 100% polyester of thickness 1 to 1.25 mm bonded to the membrane with intermittent touch by heating the membrane by Butane Torch as per manufactures recommendation.

Grading roof for water proofing treatment with

Cement concrete 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner.

Miscellaneous works

Providing plinth protection 750 mm wide consisting of 12 mm thick cement plaster 1;6 with neat cement punning over 75 mm thick P.C.C. (1:3 :6) over brick flat soling over 75 mm thick local sand filling all complete

Providing plain cement concrete in (1:2:4) including making grooves laid in pattern of tiles 300 x 300 mm avg. thickness 40 mm on sloped roof as per drawings all complete.

Making khurras 45 x 45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1mx1mx400micron, finished with 12mm cement plaster 1:3 (1cement:3 coarse sand) and a coat of neat cement rounding the edge sand making and finishing the outlet complete.

Supplying chemical emulsion in sealed containers including delivery as specified.

Chlorpyriphos / Lindane emulsifiable concentrate of 20%.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :

Diluting and injecting chemical emulsion for POSTCONSTRUCTIONAL anti-termites' treatrnent (including the cost of chemical emulsion)

Along external wall where the apron is not provided using chemical imulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300 mm including excavation channel along the wall & rodding etc. complete.

With chlorpyriphos / Lindane E.C. 20% with 1% concentration.

Along the external wall below concrete or masonary apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.

With Chlorpyriphos / Lindane E.C. 20% with 1% Concentration.

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement : 2 coarse sand ) to match the existing floor.

With chlorpyriphos / Lindane E.C. 20% with 1% concentration.

Providing and fixing sheet covering over expansion joints with iron screws as per design to match the colour / shade of wall treatment.

Aluminium fluted strips 3.15 mm thcik

200 mm wide

Providing and filling in position bitumen mix filler of Proportion 80 kg of hot bitumen, 1 kg of cement and 0.25 cubicmetre of coarse sand for expansion joints.

Providing well burnt brick bats or Jhama bricks including ramming properly till compacted thickness is achieved, curing and carriage of water with all leads, making proper slope and blinding the top with cement mortar (1:10) all complete as per building specification and direction of E/I.

Carriage of Materials

Bricks

Coarse Sand from BANKA

Stone Chips from PAKUR Rack

Local sand

Difference in cost of Materials

Cement

Bricks

SOR-22 Code

15 mm nominal bore

White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Flexible pipe

600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms

100mm dia.

Hubless Centrifugally cast (spun) iron pipes epoxy coated inside & outside IS : 15905

For 100 mm dia pipe

Hubless Centrifugally cast (spun) iron pipes epoxy coated inside & outside IS : 15905

Hubless Centrifugally cast (spun) iron pipes epoxy coated inside & outside IS : 15905

100 x 100 x 100 x 100 mm

Hubless Centrifugally cast (spun) iron pipes epoxy coated inside & outside IS : 15905

Hubless Centrifugally cast (spun) iron pipes epoxy coated inside & outside IS : 15905

Hubless Centrifugally cast (spun) iron pipes epoxy coated inside & outside IS : 15905

100 mm inlet & 100 mm outlet

Hubless Centrifugally cast (spun) iron pipes epoxy coated inside & outside IS : 15905

100 mm diameter pipe

110mm diameter

Single pushfit Coupler:

Shoe plain

White Vitreous china Orissa Pattern W.C pan of size 580x440mm with integral type foot rests.

W.C pan with ISI marked white solid plastic seat and lid.

One urinal basin with 5 litre white P.V.C. automatic flushing cistern.

Range of three urinal basin with 10 litre white P.V.C. automatic flushing cistern.

Range of two squatting plates with 5 litre white P.V.C. automatic flushing cistern.

White Agaria Marble Stone

50 mm dia

150 mm diameter

150mm diameter S.W. pipe

180 x 150mm size P type

Particulars

Compacting original ground Compacting original ground supporting subgrade (Loosening of the ground upto a level of 500 mm below the subgrade level, watered, graded and compacted in layers to meet requirement of table 300-2 for subgrade construction)

Construction of subgrade and Earthen Shoulder (Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2)

Granular Sub-Base with Graded Material ( Table:- 400- 1) Plant Mix Method (Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401.)

Rate per cum for grading-II Material

Supplying and Filling in Plinth with local sand and under floors including, watering, ramming consolidating and dressing complete.

Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level.

1:3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

brick edge soling

Centring and shuttering including strutting, propping etc. and removal of form for.

Edges of slabs and breaks in floors and walis- above 20 cms wide

Providing and laying factory made chamfered edge Cement Concrete paver blocks of required strength,thickness & size/shape, made by table vibratory method , to attain superior smooth finish using PU or equivalent moulds, laid in required Grey colour & pattern over 50mm thick compacted bed of coarse sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with jamuna sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks,lawns, drive ways or light traffic parking etc. all complete as per manufacturer’s specifications & direction of Engineer -in-Charge:

(a) 80 mm thick c.c. paver block of M-35 grade with approved colour design and pattern.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

CARRIAGE OF MATERIALS :

Bricks

Stone Chips

Stone Metal

Coarse Sand

Local sand

Earth

Diffrence in Cost of Materials

Cement

Bricks

Particulars

Excavating, supplying and filling of local earth (including royalty but excluding cairriage cost) by mechanical transport upto a lead of 3km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. If local earth is available at more than 3 km lead the actual lead must be approved by compitent authority. cairraiage of material will be paid seperately and calculated after deducting initial lead.

Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunks and branches removing the roots and stacking of serviceable material and disposal of unserviceable material.

Beyond 30 cm girth up to and including 60 cm grith

Carriage of Earth

Particular

Water Supply Works

Sewarage & Drainage

Strom Water Drains

Drain (D1) - 101 mtr. Rectangular Section, 300 x 400

Drain (D2) - 20 mtr. Rectangular Section 500 x 600

Drain (D3) - 30 mtr. Rectangular Section 500 x 750

Drain Cover - 30 mtr.

Septic Tank

Septic Tank -- 3 Nos. x @ Rs. 2,44,209/- 6.0 mtr (long) x 2.0 mtr (wide) x 2.25 mtr (deep) {of inside finished size as per design & drawing

Tube Well - 2 Nos.

Description of work

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc . (external work)

40mm dia nominal bore

50mm dia nominal bore

Providing and fixing gun metal non-return valve of approved quality (screwed end)

40 mm nominal bore

Vertical

50 mm nominal bore

Horizontal

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

40mm nominal bore

50 mm nominal bore

Painting G.I. pipes and fittings with two coats of anticorrosive bitumastic paint of approved quality :

40 mm dia meter pipe

50 mm dia meter pipe

Description of work

Providing & filling sand of grading zone V or coarser grade all-around G.I. pipes in external work.

40 mm diameter pipe

50 mm diameter pipe

Providing and fixing G.I Union in G.I pipe including cutting and threading the pipe and making long screws etc. complete (New work)

40 mm nominal bore

50 mm nominal bore

Providing and fixing Brass bib cock of approved quality.

15 mm nominal bore, 86 mm long. Weighting not less than 88 gms.

Providing and fixing brass stop cock of approved quality .

20 mm nominal bore

Constructing masonry Chamber 30 x 30 x 50 cm inside, in brick work in cement mortar 1:4( 1 cement: 4 coarse sand) for stop cock, with C.I surface box 100 x 100 x 75 mm(inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) i/c necessary excavation, foundation concrete 1:5:10( 1 cement: 5 fine sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3(1 cement: 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design:

With common burnt clay F.P.S(non modular) bricks of class designation 100 A

Description of work

Constructing masonry Chamber 60 x 60 x 75 cm inside, in brick work in cement mortar 1:4(1 cement: 4 coarse sand) for sluice valve, with C.I surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) i/c necesary excavation, foundation concrete 1:5:10( 1 cement: 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3( 1 cement: 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design:nt complete as per standard design.

With common burnt clay F.P.S (non modular) bricks of class designation 100 A

Providing, laying and jointing glazed stoneware pipes class SP-1 with with stiff mixture of cement mortar in the proportion of 1:1(1 cement: 1 fine sand) including testing of joints etc. complete.

150 mm diameter

Providing and laying cement concrete 1:5:10( 1 cement: 5 coarse sand:10 graded stone aggregate 40mm nominal size) all-round S.W pipes including bed concrete as per standard design.

150 mm diameter S.W. pipe

Providing and fixing square-mouth S.W gully trap class SP-1 complete with C.I grating brick masonry chamber with water tight C.I cover with frame of 300 x 300 mm size(inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:

150 x 100 mm size P type

With common burnt clay F.P.S (non modular) bricks of class designation 7.5

Description of work

Providing and laying non-pressure NP2 class (light duty) R.CC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2( 1 cement: 2 fine sand) including testing of joints etc. complete.

100 mm dia R.C.C pipe

150 mm dia R.C.C pipe

Excavating trenches of required width for pipes cables, etc, including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m including getting out the excavated soil , and then returning the soil as required , in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed , within a lead of 50 m.

Pipes, cables etc. ecceeding 80 mm dia . But not exceeding 300mm dia.

Constructing brick masonry manhole in cement mortar 1:4(1 cement: 4 coarse sand) with R.C.C top slab with 1:2:4 mix (1 cement:2 coarse sand: 4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement: 4 coarse sand:8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3( 1 cement: 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement: 2 coarse sand:4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design:

Inside size 90 x 80 cm and 45 cm deep including C.I cover with frame (light duty) 455 x 610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg)

With common burnt clay F.P.S (non modular) bricks with class designation 7.5

Extra for depth for manholes Size 90 x 80 cm with common burnt clay F.P.S (non modular) bricks of class designation 7.5

Description of work

Constructing brick masonry chamber for underground C.I inspection chamber and bends with bricks in cement mortar 1:4( 1 cement: 4 coarse sand) C.I cover with frame (light duty) 455x610mm internal dimensions, total weight of cover with frame to be not less than 38 kg(weight of cover 23 kg and weight of frame 15 kg) R.C.C top slab ith 1:2:4 mix ( 1 cement: 2 coarse sand:4 graded stone aggregate 20mm nominal size) foundtion concrete 1:5:10( 1 cement: 5 fine sand:10 graded stone aggregate 40mm nominal size), inside plastering 12mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:

Inside dimensions 455 x 610 mm and 45 cm deep for single pipe line:

With common burnt clay F.P.S (non modular) bricks of class designation 7.5

Extra for depth beyond 45 cm of brick masonry chambar For 455x610 mm size With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

With common burnt clay F.P.S (non modular) bricks of class designation 7.5

Providing 150mm wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 125mm apron concrete (1: 4:8), over one brick designation 100-A flat soling in proper grade and slope at the base, the drain duly plastered in CM. (1:3) with punning over exposed surface all complete as per building specification and direction of E/l,

Item Code

All kinds of soil

1:2:4 ( 1 Cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size)

1.4.8 (1 Cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size)

Cement mortar 1:4 (1 Cement :4 coarse sand)

1:4(1 Cement :4 coarse sand)

Foundations, footings, bases of columns etc for mass concrete.

Carriage of Materials

Difference in cost of Materials

per 1000 nos

Item Code

All kinds of soil

1:2:4 ( 1 Cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size)

1.4.8 (1 Cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size)

Cement mortar 1:4 (1 Cement :4 coarse sand)

1:4(1 Cement :4 coarse sand)

Foundations, footings, bases of columns etc for mass concrete.

Carriage of Materials

Difference in cost of Materials

per 1000 nos

Item Code

All kinds of soil

1:2:4 ( 1 Cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size)

1.4.8 (1 Cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size)

Cement mortar 1:4 (1 Cement :4 coarse sand)

1:4(1 Cement :4 coarse sand)

Foundations, footings, bases of columns etc for mass concrete.

Carriage of Materials

Difference in cost of Materials

per 1000 nos

S.O.R. No.

Suspended floors, roofs, landings, balconies and access platform.

Carriage of Material

Coarse Sand (Lead - 160 K.m pucca) from Koilwar

Stone Chips (Lead - 58 K.m) from Chakiya Rack

Diffrence in Cost of Materials

Cement

Item Code

All kinds of soil

Ali kinds of soil.

1:2:4 ( 1 Cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size)

Cement mortar 1:6 ( 1 cement: 6 coarse sand)

Cement mortar 1:4 ( 1 cement: 4 coarse sand)

1:2:4 ( 1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size)

Foundations, footings, bases of columns etc. for mass concrete.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts

Suspended floors, roofs, landings, balconies and access platform.

Thermo-Mechanically Treated bars TMTC-500-8mm dia.

Thermo-Mechanically Treated bars TMTC-500-10mm dia.

Thermo-Mechanically Treated bars TMTC-500-12mm dia.

500 mm diameter C.I cover (medium duty) the weiht of he cover to be not less than 58 kg.

With 20x20mm square bar

Carriage of Materials

Difference in cost of Materials

per 1000 nos

Description of Work

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level.

All types of soil

300 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths,as per direction of Engineer -in-charge.

150 mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

150 mm nominal size dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.

150 mm clamp

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe,removable as per requirement, all complete for borewell of:

150 mm clamp

Gravel packing in tubewell construction in accordance with IS:4097,including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully develo ped, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.

25 mm dia nominal bore

40 mm dia nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

40 mm nominal bore

Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws, including excavation,refilling the earth or cutting of wall and making good the same complete wherever required :

40 mm nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

20 mm nominal outer dia Pipes

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer - in-charge.

Supply fixing 2 HP Motor Pump (1 Unit) with 32 mm dia clamp (1 Unit), Suitable Length of cable, Panel Board & Starter (1 No.), centre Guide ( 6 Nos.) Machine Up and Down etc. all complete

a) 8mm dia

b) 10mm dia

c) 12mm dia

Grade Beam, Plinth Beam and Lintel

Column

Carriage cost of Materials.

Coarse Sand Lead

Stone Chips Lead -

Local Sand Lead - ( 2P + 1K )

Bricks Lead - (7P + 1K )

Difference cost of Materials.

Cement

Bricks Lead - (7P + 1K )

BCD KATIHAR

Item of Work

Local Sand

B/F SOLING

Brick Work cm(1:6)

Description of Work

Earth Work

Earth work in excavation over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m; disposed earth to be levelled and neatly dressed.

All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth : consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m

Extra for every additonal lift of 1.5 m or part thereof in :

All kinds of soil

Supplying and filling in plinth with local sand and under floors including watering, ramming consolidating and dressing complete.

Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/I.

Concrete Work

Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level.

1: 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

Extra for providing and mixing water proofing material in cement concrete work in the proportion recommended by the manufactures.

Reinforced Cement Concrete

Centring and shuttering including strutting, propping etc. and removal of form for:

Foundations, footings, bases of columns, etc., for mass concrete.

Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform

Edges of slabs and breaks in floors and walls

Under 20 cms wide

Reinforcement for RCC work including straightening. Cutting, bending, placing in position and binding all complete.

8 mm dia

10 mm dia

12 mm dia

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering finishing and reinforcement, M-20 grde reinforcd cement concrete

All work upto plinth level

Brick Work

Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in Cement mortar 1:4 (1 cement : 4 coarse sand)

Steel works

Steel work welded in built up sections/framed work including cutting hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladders, railings, brackets, gates & similar works

Plaster and Finishing Works

12 mm cement plaster of mix

1:3 (1 cement:3 coarse sand)

15mm cement plaster 1:3 (1cement : 3 coarse sand) finished with a floating coat of neat cement on the rough side of single or half brick wall

6 mm cement plaster to ceiliing of mix :

1:3:(1 cement : 3 fine sand)

Neat cement punning

Miscellaneous Works

Supplying and fixing C.I. cover without frame for manholes :

560 mm diameter C.I. over (heavy duty) the weight of the cover to be not less than 108 kg.

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.

80 mm dia. Nominal bore

Providing and fixing vent pipes :

100 mm dia Sand cast iron S&S pipe as per IS : 1729

Providing and fixing in position 25mm diameter mosquito proof coupling of approved municipal design

Providing and fixing C.I. sluice valves (with cap) complete with bolts,nuts, rubber insertions etc. (the tail pieces if required will be paid separately) :

100 mm diameter Class I

Carriage of Materials

Bricks (lead - 1 km kutcha + 7 km pucca)

Coarse Sand (Lead - 189 K.m pucca) from Koilwar

Stone Chips (Lead - 87 K.m) from by rail from pakur

Local sand (1 km kutcha + 2 km pucca)

Diffrence in Cost of Materials

Cement

Bricks

Description of Work

Clearing jungle including uprooting or rank vegetation, grass, brush wood, trees and scaplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared.

Trenching in ordinary soil upto a depth of 60 cm including removal and stacking of serviceable materials and then disposing of by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge of / and manure before and after flooring trench with water (excluding cost of imported earth, sludge or manure)

Supplying and stacking of good earth at site including royalty but excluding carriage (earth measured in stacks will be reduced by 20 % for payment)

Supplying and stacking at site dump manure from approved source, excluding carriage (manure measured in stacks will be reduced by 8% for payment)

Screened through sieve of I.S. designation 4.75 mm

Mixing earth and sludge or manure in proportion specified or directed.

Spreading of sludge, dump manutre or/and good earth in required thickness (Cost of sludge, dump manure or/and good earth to be paid separately)

Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm removing all weeds and other growth with roots by forking repeatedly, breaking clods, rought dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts.

Grassing with 'Doob' grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free form weeds and fit for moving including supplying good earth if needed.

In rows 5 cm apart in either direction.

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20 % 1 part of stacked volume of manure after reduction by 8 % ) flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and lifts (cost of manure sludge or extra good earth if needed to be paid for separately)

Holes 1.2 m dia. And 1.2 m deep.

Holes 60 cm dia. And 60 cm deep.

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8 :1 (8 parts of stacked volume of earth after reduction by 8% ) flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and levelling as directed, within a lead of 50 m lift upto 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)

Plantation of trees & Shrubs/ creeps.

Providing and stacking of Bauhinia blakeana (Kachnar) of height 120-150 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Delonix regia (Gulmohar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.v

Providing and stacking of Cassia fistula (Amaltash) of height 120-135 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Cassia biflora of height 90-105 cm., well branched, bushy in big size HDPE bag as per direction of the officer-in-charge.

Providing and stacking of Hamelia patens of height 90-105 cm. bushy in big size HDPE bags as per direction of the officer-in-charge.

Providing and stacking of Mussaenda erythrophylla (Rosea) of height 60- 75 cm. multi branched in earthen pots of size 25 cm as per direction of the officer-in-charge.

Earth work in excavation in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, with in a lead of 50 m.

All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level.

1:3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in :

Half brick Masonary Cement mortar 1.:4 (1 cement: 4 coarse sand ) - 125 mm th Brick work

12 mm cement plaster of mix :

1:4 (1 cement : 4 coarse sand)

Applying one coat of cement primer of approved brand and manufacture on wall surface :

Cement primer

Finishing walls with water proofing cement paint of approved brand and manufacture and of required shade to give an even shade

New work ( three or more caots)

Carriage of Materials

Bricks

Coarse Sand

Stone Chips

Earth / Manure

Difference in Cost of Materials

Bricks

Cement

Floor Name

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

Gr. Floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

1st floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

2nd floor

Item Description / Specification

Interior works

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ?85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking TGrid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm ) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The

With 16 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.55 to 0.6)

Providing and fixing anodised aluminium work for doors, windows, ventilator? and partitions with extruded built up standard tubular and otner sections of approved make conforming to IS : 733 and IS : 1285,anodised trasparent or dyed to required shade according to IS : 1868,(Minimum anodic coating of grade AC 15), fixed with.rawl plugs and screws or with fixing clips , or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust fre straight, mitred and jointed mechanically wherever required including cleat angle,.Aluminium snap beading tor glazing/paneling, C.P. brass/stainless steel screws, all complete as per architecttural drawings and the directions of Engineer-in-charge.(Glazing and panelling to be paid for separately.)

For fixed portion

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.

Pre-laminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber /neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 8 mm thickness

Sor no./Ns

7.0 BCD-SOR-22

150 mm dia

100 mm dia

80 mm dia

50 mm dia

25 mm dia

2.10 BCD-SOR-22

Pipes, cables etc. exceeding 80 mm dia . But not exceeding 300mm dia.

14 BCD-SOR-22

100 mm dia

11 BCD-SOR-22

150 mm dia

100 mm dia

80 mm dia

Internal Hydrant System

6.0/ 10 BCD-SOR-22

Single headed Gunmetal

Single headed Stainless Steel

17 BCD-SOR-22

16.2 BCD-SOR-22

19.2 BCD-SOR-22

External Hydrant System

16.2 BCD-SOR-22

18.1 BCD-SOR-22

Fire Pumps & Accessories

1.0 BCD-SOR-22

Main fire Pump

3.0 BCD-SOR-22

180 lpm at 70 m Head

4 BCD-SOR-22

450 lpm at 35 m Head

22 BCD-SOR-22

Providing and fixing motor control centres fabricated from 16 gauge M.S. sheet with Powder Coated finish. The control panels should be compatible with H.P. of the motor as under and as per spcifications with automatic star delta starters. (One separate panel to be located in the plant room).

One incoming main isolation MCCB TP of Min. 250 Amps. rating.

Fully taped aluminium bus bar of required capacity in a separate bus bar chamber.

Isolation MCCB for each unit of required rating and with fully automatic starter as per requirement with push button and ON/OFF indicating lights for each unit, for following requirements:

One main fire pump of 50 HP.

One jockey pump of 10 HP (Each).

One Diesel Pump Controlling System

Single phasing preventors of suitable rating one for each motor.

One 96mm square panel type Amp. meter reading 0-500 Amp. for main fire pump and sprinkler pump.

One 96mm square panel type Amp. meter reading 0-500 Amp. for each Jockey pumps.

Appropriate etched plastic plate for each starter/switch.

Colour coded internal wiring from incoming main to bus bar, switch gear, starters, meters indicating lamp etc., complete in all respects.

Power cable 3 core 16 Sq.mm

Power cable 3 core 25 Sq.mm

Fire Alarm System

17.2/ E&M DSR-22

Two Loop Panel.

17.1.2/E&M DSR-22

17.2.7/E&M DSR-22

17.2.14/E&M DSR-22

17.2.15/E&M DSR-22

17.5.3.2/E&M DSR-22

Automatic Sprinkler System

21 BCD-SOR-22

Upright Sprinkler

Fire Extinguishers

All kinds of soil

Carriage of Materials

Cement

Bricks

Items

Carriage of Materials

Bricks (Lead - 1 km kutcha + 7 km pucca)

Coarse Sand (Source- Banka)

Stone Chips (Source- Pakur)

Local sand (1 km kutcha + 2 km pucca)

Difference in cost of Materials

Cement

Bricks

300 mm dia

150 mm nominal size dia

150 mm dia

150 mm clamp

150 mm dia

110 mm diameter

Coupler, 110mm

Single Tee withdoor, 110x110x110mm

Band 87.50, 110mm band

Shoe plain, 110mm shoe

With common burnt clay F.P.S.(non modular) bricks of class designation 100A

Detailed