SPL REPAIR TO RCC ROOF IN BLDG NO. BI-16 INCLUDING INTERNAL ELECTRIFICATION WORK, ADDN/ALTN TO JCO MESS BLDG NO P-25B AT ECPU , PROVN OF FALSE CEILING, WALL PLASTERING AT OFFICERS RATION STAND (ORS), HQ EASTERN COMMAND (ADM BR) AND PROVN OF PVC WALL

Amount

SCHEDULE 'A' PART-I (B/R WORKS) Dismantling of AC corrugated/semi corrugated sheets including ridge as in roof covering and removing off the site complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 150 mm thickness (above or below groud level) complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description in any position not otherwise specially provided for complete all as specified and as directed.

Demolition of brick work or stone boulder masonry built in cement mortar including all quaries, arches pillars etc and removing off the site complete all as specified and directed.

Taking down cement plaster from brick or concrete surfaces of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as directed.

Dismantling floor hearth or wall tiling of any description of any thickness incl cement mortar bedding etc all as specified and directed.

Dismantling stone slabs and tiles, laid, bedded and pointed in any mortar of any description or thickness in floors, aprons etc complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description in rafters, purlins and wind ties wtc complete all as specified and directed.

Dismantling of ceiling board incl snap grid frame of any thickness including cover fillets complete all as specified and directed.

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) area n.exc. 1.5 Sqm each all as specified and directed.

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) area exc 1.5 Sqm and n.exc.4.00 Sqm each wooden all as specified and directed.

Hacking out old broken glass (any thickness and size or quality) from wooden frames glazed with putty or fixed with beads complete all as specified and directed.

Excavation in trenches n exc 1.50 m wide and n exc 1.50m depth for foundation etc or for shafts, wells, cess pits, manholes, pier holes etc not exc 10 Sqm on plan and not exc. 1.50 Metre in depth and getting out as in soft/loose Soil, complete all as Specified and as directed.

All as per Item No. 13 above, but in road/hardstanding etc and getting out

Removing excavated materials not exc 50 m and depositing where directed at a level not exc 1.50 m above the starting point complete all as Specified and as directed.

Returning filling in incl spreading , levelling , watering and well ramming in layers not exc 25 cm as in soft/ loose Soil, complete all as Specified and as directed.

M&L for Cement Concrete type B-1, (1:2:4) using 20mm graded crushed stone aggregate in copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed including use and waste formwork (straight or curved) complete all as specified and as directed.

M&L for RCC 1:1½:3 type A1 (using 20 mm graded aggregate) as in slabs supported on walls, beams and columns in floors, roofs, drain, ducts, canopies etc. complete complete all as specified and as directed. (NOTE: MS reinforcement shall be measured and paid seperately)

M&L for RCC 1:1½:3 type A1 (using 20 mm graded aggregate) as in fins, fascias, louvers, parapets and railings etc complete complete all as specified and as directed. (NOTE: MS reinforcement shall be measured and paid seperately)

S&F in repair 35mm thick precast cement concrete Type B-0 (1:2:4) (using 12.5 mm graded crushed stone aggregate) louvers and jallies including all moulding, but excluding frame set in cement mortar 1:4, complete all as specified and as directed.

M&L Brick Work with fly-ash Bricks (with Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and as directed.

M&L Brick Work with fly-ash Bricks Half-Brick thick, Old Size, built in Cement Mortar 1:4, Straight or Curved on Plan to any Radius, complete all as specified and as directed.

M&L for cutting holes in brick wall exceeding half brick but not exc one brick thick walls for inserting hold fasts for mild steel grills and making good dismantled portion in cement concrete 1:2:4 type B1 (using 20 mm graded aggregates) including necessary formwork and making good surfaces as per existing finishes complete all as specified and directed.

M&L for Mild steel framed works such as grills, gratings etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings, framework of water tanks and similar works conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (horizontal or sloping) for fair finished surfaces complete all as specified and directed.

S&F for 2nd class hardwood, plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, moulded or chamfered, put together with glue, pinned at joints complete all as directed.

S&F Factory made 35mm thick with 2nd class hard wood, rail and style factory made plain framed panelled shutter(two panel) with lock, rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail & style as per IS:1003(Part-I) kiln seasoned and chemically pressure treated complete all as specified and directed.

Providing and fixing factory made uPVC white colour Sliding window Three track, area not exceeding 2.00 sqm each, made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories complete all as specified and directed. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.)

S&F Factory made solid PVC door frame (chowkhat) of size 100 mm x 45mm made out of 5mm plain colour PVC sheet, frame reinforced with MS square tube of size 40mm x 20mm of 19 guage throughout the frame, fixed in opening as per specification & drg as per manufacturer instructions complete all as specified and directed.

M&L for Factory made solid PVC moulded door shutter, 28 to 30 m thick(stiles) with 2,4 or 6 raised panel design with 2 mm thick moulded PVC sheet on the front face & 2 mm plain colour PVC sheet on back face with particle board core complete all as specified and directed.

M&L for Anodized aluminum frame for doors, windows, ventilators and partition with one or more rebate including joining cleat for fixing etc complete all as specified and directed..

M&L for anodised aluminium door shutters, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc complete all as specified and directed. (NOTE: Glass shall be measured and paid seperately)

S&F Butt hinges, medium weight, cold rolled mild steel, size 100 mm complete all as specified and directed.

S&F Extruded aluminium alloy handles, fabricated type, anodised, 150 mm complete all as specified and directed.

S&F for Aluminium anodised barrel tower bolts of extruded sections, 150 mm long complete all as specified and directed.

S&F for Aluminium anodised barrel tower bolts of extruded sections, 200 mm long complete all as specified and directed.

S&F 300mm aluminium, anodised sliding door bolt with hasp, staple(bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy all as directed complete all as specified and directed.

S&F Floor door stopper of brass body and tongue, anodised, with hard drawn steel spring, fixed in floor, overal length of cover plate 140 mm complete all as specified and directed.

S&F Door closer hydraulically regulated, designation No. 3, universal type, aluminium (die cast) body, suitable for door shutters of 851 to 1000 mm in width & weight between 61 to 80 kg complete all as specified and directed.

S&F 4 lever mild steel type Mortice lock vertical type size 100mm complete all as specified and directed.

S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised, width of flaps (when open) 30 mm complete all as specified and directed.

S&F stainless steel handle 150 mm long decorative type complete all as specified and directed.

S&F multipurpose cupboard lock, brass, 50 mm size complete all as specified and directed.

S&F cupboard magnet, heavy duty complete all as specified and directed

S&F stainless steel tower bolt, 120 mm long, heavy duty complete all as specified and directed.

S&F double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box main body with stainless steel cover governing pivot made of brass, other part made of mild steel heavy duty complete all as specified and directed.

M&L mild steel work in tubular trusses including special shaped washers etc complete using ERW or induction butt welded tubes conforming to IS-1161:2014 grade St-240 complete all as specified and directed. (NOTE: Quoted rates shall be deemed to include for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete)

S&F plates (plain or chequered) channels, square cut or notched (ordninary and counter sunk) forming holes, without any attachment all as specified rolled mild steel in stairs (framed) including stringers, treades landing, balusters, hand rails etc including cleats, brackets etc complete all as specified and as directed.

M&L for Mild steel framed works such as grills, gratings etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings, framework of water tanks and similar works conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L TMT Bars 10 mm dia and over, cut to length, bent to shape required including crank-ing, bending and binding with and including Mild Steel Wire (annealed) not less than 0.90 mm, complete all as specified and as directed.

M&L TMT Bars 6-8 mm dia and over, cut to length, bent to shape required including crank-ing, bending and binding with and including Mild Steel Wire (annealed) not less than 0.90 mm, complete all as specified and as directed.

M&L for TMT bars 5 mm dia and over upto and including 10 mm dia in stirrups , spacers and binders cut to length , bent to shape required as in reinforcement and binding with MS wire ( annealed ) not less than 0.90 mm dia complete all as specified and directed .

M&L for Expanded metal, cut to length, bent to shape required and tying with and including anealed mild steel wire not less than 0.9 mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members, weight n exc 4 Kg per sqm complete .

M&L for Expanded metal, cut to length, bent to shape required and tying with and including anealed mild steel wire not less than 0.9 mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members, weight exc 4 Kg per sqm complete all as specified and directed.

S&F 0.50 mm thick TCT (total coated thickness) pre-coloured galvalume sheets with minimum base metal thickness of 0.45 mm, single skin high rib/multi rib profile galvalume sheeting having 1000-1020 mm width and 28-30 mm high crest @ maximum 250-255 mm pitch (centre) with sheets manufactured out of 0.50 mm this TCT (total coated thickness) high tensile galvalume sheets having tensile strength 550 MPA with 18-20 micron top coat over 5 micron primer and 8-10 micron alkyld backer zinc aluminium alloy AZ-150, sheets having a dip metallic zinc (43.5%0 aluminium (55%) & silicon (1.5%) with total mass coating of 150 gms/sqm on both sides, having wide pans with minimum 3 small stiffening ribs for effective water shedding and special male/female ends with full return legs on laps for purlin support and fixed as per existing profile of roof complete all as specified and directed.

All as per Item No. 55 above but 0.50 mm thick coloured plain galvalume sheet as in ridge/valley gutter of roof.

S&F in repair 2mm thick fibre glass reinforced transluent corrugated or plain coloured/printed sheeting with two corugation side lap fixed with coach screw and washer in roof, wall etc complete all as specified and directed.

Removal of existing water proof treatment of any description from roof surface including cement plaster/screed bed carefully from the surfaces, roughening concrete surfaces and cleaning the roof surfaces by brushing, sweeping and scrubbing down with water and removal of debris complete all as specified and as directed.

M&L for brushing cement slurry @ 2.75 Kg/sqm over cleaned roof surface prior to application of concrete complete all as directed by Engineer - in - charge .

M&L for Providing Cement Concrete, type B-0, 1:2:4 (using 12.50 mm graded Stone aggregate), as in roof padding, of thickness as required on site, for making good depression/undulation, roof kerb etc, finished even and fair complete all as directed.

M&L 10 mm thick screed bed in cement mortar 1:3 over roof mixed with water proofing compound as per manufacturer's instruction complete all as specified and directed. (NOTE: WPC will be measured and paid separately)

M & L for cutting Grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 or cement concrete 1:2:4 type-B1 as required complete all as specified and directed.

M&L for water proofing treatment on existing cleaned RCC roof with the following specifications and manufacturer's instruction complete all as specified and directed :- (i) Preparing and cleaning of fully dried surfaces as per IS 3067-1966. (ii) Applying bitumen primer conforming to IS:3384-1968 over the cleaned base @ 0.50 litre per sqm. (iii) Providing a layer of 3 mm thick APP modified pre-fabricated five layer, weight not less than 3.6 kg/sqm, black finished reinforced with non-woven polyster matt membrane with butane torch application. Overlap shall be minimum 100 mm on the transverse direction and 75 mm on longitudinal direction. (iv) Applying two coats of bitumen based UV reflective paint with aluminium finish @ 0.10 litre per sqm over APP membrane.

S&F 10 to 12mm thick gypsum board false ceiling including 0.55mm thick GI perimeter channel, GI channel tray frame work having one flange of 20mm and another flange of 30mm with web of 27mm, GI intermediate channel of size 45mm x 0.90mm thick with two flange of 15mm each suspendded form the soffit of roof slab/truss @ 1220mm c/c with MS angle of suitable size fixed to soffit of ceiling with GI cleat and expansion fastener with and including necessary nuts and bolts and gypsum board is screwed to ceiling section with stainless steel screws @ 230mm c/c complete all as specified and directed.

S&F Block boards 18 to 19 mm thick, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame-work (as in cup board etc) complete all as specified and as directed.

S&F 0.90 mm thick laminate, fixed to ply wood or blockboard with suitable adhesive complete all as specified and directed.

Supply and Fixing PVC solid wall lining consisting of 5 mm thick single side prelam PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per manufacturer’s specification and instruction and as directed.

Supply and Fixing 5mm thick PVC sheet fillet of width 35 mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification and drawing.

M&L 09mm thick Prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination & other side balancing white lamination, fixed with screws to frame work etc complete all as specified and directed.

S&F Suspended metal grid Ceiling System with mineral fibre acoustic tiles as per following specifications:- a) Ceiling Tiles:- Mineral fibre acoustic tile of 16mm thickness having sand textured finish with acoustical punchers, bevelled tegular edge and 8mm drop in module size of 600 x 600mm. Tiles shall have humidity reistance (RH) of 99%, NRC 0.50 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 standard, CAC of 33db as per ASTM E1414, Light Reflectance ≥85% as per ASTM E-1477, Thermal Conductivity k = 0.052 - 0.057 W/mK, Colour Global White, Fire Performance of class 0/1 as per BS 476 Part 6/7 and Class A as per ASTM E84. b) Metal Grid:- The grid system shall be 15 mm wide T - section flanges colour global white (matching to tile color) having roll formed double stroke rotary stitching on all T sections i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 38mm (all sections). The deflection loading of the system shall be 12.5 kg/m2 (as per standard installation layout mentioned below) and main beam tested as per ASTM C635 (Deflection limit less than L/360) with a deflection loading of 15kg/m. The end details of the cross tee shall be made of pre hardened steel and fixed to the ends of the cross tee to provide double locking between “cross tee to cross tee” and “cross tee to main beam”.

(Item No. 70 Contd....) All main beam to main beam and cross tee to cross tee connection shall have a pull out strength of more than 100kg. The T Sections shall be made of hot dipped galvanized steel of 90 gsm as per IS 277 (2003) and pre-painted steel with baked polyester paint with 0T bending capability. The ceiling grid sections shall be fixed to ceiling with 6 mm dia GI hangers upto required length by means of ceiling cleats made out of GI flat 40 x 3 mm size 60 mm long and expansion hold fasteners 12.5mm dia 40 mm long. MAKE OF CEILING GRID : ARMSTRONG, Model: SUPRAFINE 38 or equivalent in GYPROC / USG BORAL / UNISTEEL MAKE OF CEILING TILES: ARMSTRONG, Model: DUNE or equivalent item in GYPROC / USG BORAL / U TONE)

M&L for dubbing out cement plaster (1:4), average 10 mm thick on irregular faces of walls (when specially ordered in writing) complete all as a specified and as directed

M&L Rendering 15mm thick, on fair faces of brick or concrete surfaces of walls in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and directed.

M&L Rendering 5mm thick, on concrete surfaces of walls in cement mortar 1:3, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick built in cement mortar (1:4) in two layers (10mm + 5 mm) on fair faces of brick work or concrete surfaces finished even & smooth (without using extra cement) and 2nd layer mixed with water proofing compound as per mnufacturer's instruction for bldg height upto 4 storey complete all as specified and directed. (NOTE : Water proofing compound shall be measured and paid seperately).

Supply only liquid water proofing compound all as specified and as directed.

S&F 4.8 mm thick sheet glass frosted on one side, area in squares exc 0.5 sqm in each pane and glazing with rubber gasket fixed to aluminium frame work / snap beading complete all as specified and as directed by the Engineer-in-Charge

M&L Non Skid joint free ceramic coloured tiles 7-8mm thick, area of each tiles exc 0.11 Sqm but n. exc 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 20 mm thick screed bedding in cement mortar 1:6 complete all as specified and directed.

M&L for non skid ceramic 8-9 mm thick coloured tiles, joint free, (square/ rectangular) area of each tile exc 0.18 Sqm but n.exc 0.38 Sqm, set and jointed in neat cement slurry and pointed in white cement mixed with pigment as in floor, laid over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

S&F Vitrified coloured (light shade) Ceramic tiles, 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.36 sqm but not exc 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including screed bed 20mm thick in cement mortar 1:6 complete all as specified and directed.

M&L Vitrified ceramic, coloured tiles, light shade 10mm thick (square/ rectangular ) polished, area of each tiles not exceeding 0.36 Sqm in floors etc set and jointed in neat cement slurry, laid over and including screed bed 15 mm thick in cement mortar 1:4 and pointed in white cement with pigment to match the surface complete all as specified and as directed.

-ditto- but fixed on vertical surfaces as in skirting over and including 10mm thick screed bed in cement mortar 1:3

M&L for glazed coloured ceramic tiles in vertical surface 300 X 450 X 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles, laid over and including 10mm thick screed bed in cement mortar 1:3 complete all as specified and directed.

M&L for granite (of any type) work, 18-20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, urinal partition and like in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and making moulds on edges laid over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

M&L for 18-20 mm thick coloured granite Slab, machine cut, as in vertical surfaces such as skirting, dado, wall cladding etc, fixed over and including 10 mm thick backing layer in cement mortar 1:3, set and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite tiles including rubbing and polishing complete all as specified and directed..

M&L for 18-20 mm thick italian marble (of any type) work (table rubbed and polished) for Flooring, laid over and incl 20mm thick screed bed in cement mortar (1:3) and fixed with 5 mm thick spacers and gap to be filled by epoxy dazzling grout (with includes 2 component resin and hardner mixed in ratio 1:4 and dazzel per 200 gms for 1 kg grout mixture pointing with match with shade of Marble) complete all as specified and directed.

Providing edge moulding to 18-20mm thick granite stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and as directed.

Providing edge moulding to 18-20mm thick marble stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and as directed.

Rounding to edges of stone slab one edge, such as in steps, cooking platforms and other similar situation complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type 'C-2' (using 40mm graded crushed stone aggregate) as in floor, plinth protection etc, surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for applying one coat of acrylic distemper to old decorated surfaces of wall including preparation of surface (by brooming down or steel wire brushing, scrapping down smoke, soot, moulds, moss, efflorescent salts, trading oil and greasy spots) complete all as specified and directed.

M&L for applying one coat of acrylic distemper to old decorated surfaces of ceilings including preparation of surface (by brooming down or steel wire brushing, scrapping down smoke, soot, moulds, moss, efflorescent salts, trading oil and greasy spots) complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying 2 mm thick wall putty over plastered surfaces, finishing surfaces even and smoooth and applying two coats of acrylic distemper over a coat of alkali resistant primer as per manufacturer's instructions complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceilings and applying 1 mm thick wall putty over plastered surfaces, finishing surfaces even and smoooth and applying two coats of acrylic distemper over a coat of alkali resistant primer as per manufacturer's instructions complete all as specified and directed.

M&L Preparing new plastered surfaces of wall and and applying Two Coats of plastic emulsion paint over a coat of alkali resistant primer and applied over 1.5 mm thick water proof wall putty complete all as specified and as directed.

M&L for applying one coat of weather proof exterior emulsion paint to old decorated surfaces of wall including preparation of surface (by brooming down or steel wire brushing, scrapping down smoke, soot, moulds, moss, efflorescent salts, trading oil and greasy spots) complete all as specified and directed by Engineer -in-Charge.

M&L for complete removal of existing treatment on old decorated surfaces of walls and applying Two Coats of weather proof exterior emulsion paint over a coat of alkali resistant primer applied over and including 1 mm thick exterior wall putty complete all as specified and as directed.

M&L for preparing newly plastered surfaces of wall and applying Two Coats of weather proof exterior emulsion paint over a coat of alkali resistant primer complete all as specified and as directed.

M&L applying two coat of acrylic distemper over a coat of primer on ceilings complete all as specified and directed.

M&L applying two coat of acrylic/plastic emulsion paoint over a coat of primer on ceilings complete all as specified and directed.

M&L Preparing new Steel or Iron Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint over a coat of Red Oxide/ Zinc Chrome Primer, complete all as specified and as directed.

M&l for preparation of old painted steel surfaces exc 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, treating ends of posts, back of chowkhats etc, with tar or coal tar black paint, area tarred exc 0.1 sqm but n. exc 0.5 sqm each complete all as specified and directed.

-ditto- but treating small articles such as holdfasts, ends of posts, back of chowkhats, etc, area n exc 0.1 sqm each

M&L for preparation of old painted wooden surface of any description over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

Disconnecting exiting water storage Tank of capacity exceeding 1000 litres but not exceeding 2000 liters for cleaning of water tank, removing of mud, sludge etc and flushing with chlorine water including supply and fixing of any damaged accessories for water Tank and re-connecting and refixing all connections complete all as specified and directed.

Supply, hoisting and fixing rotational moulded polyethylene water storage tank (cylindrical vertical type with closed top) of capacity 2000 Litres, multi-layered (ISI marked), with GI tank nipple & cover, hoisted and fixed in position all as specified in SSR Part-I incl dismantling of existing unsv tank and writing CA No & Year with synthetic enamel paint complete all as specified and directed.

S&F 25 mm bore Ball brass valves, high pressure, with HDPE float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed. (MAKE : PRAYAG, Cat No. B-153 or equivalent model in JEXON / POLYTUF / SHAKTI)

S&F in repair tubes 15mm bore medium grade galvanised with all fittings and fixed complete to wall and ceiling or laid in floors.

-ditto all as per item No 109 here-in-before but 20 mm bore

-ditto all as per item No 109 here-in-before but 25 mm bore

-ditto all as per item No 109 here-in-before but 40 mm bore

S&F in repair gun metal gate or globe valve, with iron wheel head, screwed both ends for iron pipe and fixed for 20 mm bore pipe complete all as specified and directed.

-ditto all as per item No 113 here-in-before but 25 mm bore

M&L Preparing new Surfaces of wall and applying Three coats of white wash complete all as specified and as directed.

S&F 4 mm thick ordinary quality plain sheet glass glass and glazing in square n.exc. 0.5 Sqm in each pane complete all as specified and directed.

S&F in repair Cast iron (sand cast) soil, waste and vent pipes 150 mm bore of any length with or without ears with cement joints all as specified, fixed on walls with clamps complete all as specified and directed.

S&F in repair CI bends for 150mm pipe (any radius) diminishing piece or tapers (large bore measured) complete all as specified and directed.

S&F in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F in repair 110mm bore PVC (SWR) bends any radius complete all as specified and directed.

Cleaning of sewage line/ storm water line of 200 mm bor, manually (by pushing a piece of bamboo split, tied with gunny bags at one end from one manhole to another manhole) and well flushing the line with water and tesing on completion complete as directed by the Engineer- in- Charge.

S&F in repair 15mm bore heavy duty PVC connector pipe of length 450 mm with PTMT coupling at both ends, screwed down for pipe as directed. (MAKE : PRAYAG, Cat No. 323 / POLYTUF, Cat No. 4003 or equivalent model in SHAKTI / JEXON / CERA)

S&F in repair Chromium plated brass Wall mixer (premium quality), concealed type incl concealed body, with both overhead and telephone shower arrangement, fixed with 15 mm bore Iron pipe complete all as specified and directed. (Make : JAQUAR, Cat No : KUP-35125PM /CERA, Cat No: F1005413 / PRAYAG, Cat No: 9880 /HINDWARE, Cat No: F360019 / ASIAN PAINTS, Cat No: SRWM104 or equivalent model in PARRYWARE) NOTE: Telephone shower shall be measured and paid seperately.

S&F in repair fancy type chromium plated telephonic hand shower (premium quality), multiflow type with flexible tube and hook screwed for iron pipe including frame complete all as specified and directed. (Make : JAQUAR, Cat No: HSH-1739 / CERA, Cat No: F7030310AB / ASIAN PAINTS, Cat No: BHTS101 / HINDWARE, Cat No: F160047 / PRAYAG, Cat No: BHS-87 or equivalent model in PARRYWARE)

S&F in repair 15mm bore chromium plated central hole basin mixer (premium quality) without popup waste system with 450mm long copper pipe and brass nut, complete all as specified and directed. (MAKE : JAQUAR, Cat No: KUP-35011BPM / CERA, Cat No : F1005451 / ASIAN PAINT, Cat No: SRBM101 / HINDWARE, Cat No: F360011/ PRAYAG, Cat No: 9851 or equivalent model in PARRYWARE)

S&F in repair Vitreous China table top Wash Basin 565 x 425 mm in size, White with 32mm dia Brass Chromium Plated Waste Fitting, making good disturbed Surfaces in Cement Mortar 1:3 complete all as specified and as directed. (MAKE : JAQUAR, Cat No: KUS-WHT-35935 / CERA, Model: CHEST / HINDWARE, Cat No. 91069 or equivalent model in PARRYWARE)

S&F in repair CP bottle trap with internal portion 32mm size with 190mm long wall connection pipe complete all as specified and directed (Make: JAQUAR, Cat No: ALD-769L250x190 / ESS ESS, Cat No: C-231C / HINDWARE, Cat No: F850003 / CERA, Cat No: F8060302/ PRAYAG, cat No: BEA-26)

S&F in repair vitreous china floor mounted rimless one piece closet (Pedestal pattern), white, including low level vitreous china valveless syphonic action type flushing cistern with inlet ball valve float, push button, flush pipe incl bracket, P/S trap, UF soft close seat cover and connecting fittings complete all as specified and directed. (Make : JAQUAR, Cat No: OPS-WHT-15853S300UF / PARRYWARE, Model: Omega / HINDWARE, Model: SPELNDOUR)

S&F in repair vitreous China Squatting pan ‘Orissa’ pattern, size 580 X 440 mm, white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, etc and including making good to floor, complete all as specified and directed. (MAKE : PARRYWARE, Cat No. C0117 / HINDWARE, Cat No. 20004 / JAQUAR, Cat No. CNS-WHT-OP01 / CERA, Model: COVY)

S&F in repairs Vitreous china, white, half stall urinal flat back with grating and union for discharge pipe (excl flush pipe and flushing cistern) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing flush pipe, grating and Union for discharge pipe incl providing 32mm bore PVC discharge pipe complete all as specified and directed. (Make of Urinal : CERA, Model: CARYS / HINDWARE, Cat No: CORTO / PARRYWARE, Model: Aquaseal N )

S&F in repair Cast iron (sand cast) soil, waste and vent pipes 100 mm bore of any length with or without ears with cement joints all as specified laid in trenches or in floors complete all as specified and directed.

-ditto- but 75 mm bore pipes fixed on walls

S&F in repair CI bends for 100mm pipe (any radius) diminishing piece or tapers (large bore measured) complete all as specified and directed.

S&F in repair 100 mm bore cast iron (sand cast) bends with access door (any radius), diminishing pieces or tapers (larger bore to be measured) complete all as specified and as directed.

S&F in repair CI branch pieces, single (equal or unequal) ordinary or inverted (spigot or socket type) or with parellel branches, for 100mm dia pipe complete all as specified and directed.

M&L concrete bed to drain pipe including packing under and haunching against the side of drain pipe after laid and tested in PCC 1:3:6 type C2 for 100 mm bore pipes complete all as specified and directed.

S&F gun metal gate valve with iron wheel head, ISI marked, screwed both ends for iron pipe for 20 mm bore complete all as specified and directed.

S&F Tubular towel rail (normal range), 20mm dia, 600 mm long between flanges including brass chromium plated, complete all as specified and directed. (MAKE : Essco, Cat No : AEC-1111 / PRAYAG, CaT No: BA-40 / ESS ESS, Cat No : AC-701 / SOMANY, Model: ETHER)

M&L for 100 mm dia cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4) complete all as specified and directed.

S&F Salt-gauged stoneware gully traps, square or round mouthed, type 'P', size 150x150 mm complete all as specified and directed.

S&F Cast iron (sand cast) soil, waste and vent pipes 100 mm bore of any length with or without ears with cement joints all as specified, fixed on walls complete all as specified and directed.

Supply and fixing 100 mm bore cast iron (sand cast) bends with access door (any radius), diminishing pieces or tapers (larger bore to be measured) complete all as specified and as directed by the Engineer-in-Charge.

S&F CI bend (any radius), diminishing pieces or tapers (larger bore measured) for 100 mm bore pipe complete all as specified and directed.

S&F CI (sand cast) Branch pieces, single (any radius, equal or unequal) for 100 mm bore pipe for any building height complete all as specified and directed.

M&L for uprooting of tree from walls of bldgs up to extended root and spraying of muratic acid of required quantity complete from any location of bldg, up to four storey height and making good disturbed surface with cement mortar (1:4) or cement concrete type C1 (1:3:6) using 20 mm graded stone aggregate etc complete all as specified and directed.

Chipping of unsound /weak concrete materials including cover plaster from RCC structural member i.e. slabs, beams, columns, lintel, chajja, fins, facia etc. of 50 mm average thickness (Any storey/ height of building/ structure) including tapering all edges, making square shoulders of cavities by air or sand blasting etc and cleaning of exposed concrete surface of lightly picking materials by air blasting or sand blasting including removal of foreign materials, loose concrete/aggregate etc and disposal of all debris out side of MOD land and complete all as specified and as directed by Engr-in-Charge.

Deduct / Add for below / over 5mm or part thereof thickness for item No 146 above (Any storey/ height of building/ structure)

M&L for applying two component structural grade polymer modified reinstatement mortar of compressive strength, flexural strength shall not be less than 45 MPa at 28 days, 7 MPa at 28 days respectively (maximum coverage area 1.30 sqm per 25 kg pack @ 10mm thickness) over a coat of epoxy bonding agent on existing surface for strengthening of beams, columns and other structural element of average thickness 25 mm and mortar shall be applied in layer not exc 6 mm thick in layers and including surface preparation as per manufacturer's instructions complete all as specified and directed (any storey/height of building/structure). (Make- Rendroc S2 of FOSROC or equivalent product in other makes specified in tender)

Material , labour and applying of high efficiency polymeric resin base film forming curing agent/compound over concrete surface and maximum coverage area 5.00 Sqm per litre as per manufacturers instruction (for any storey/ height of building/ structure) complete all as specified and as directed. (Make:- Concure LP90 of FOSROC or equivalent product in SIKA / PIDILITE / BASF / CHOKSEY)

SCHEDULE 'A' PART-II (INTERNAL ELECTRIFICATION WORKS) Taking down copper/ aluminium point wiring (light, fan, buzzer, socket or power) complete including fixture and fittings such as switches, ceilling roses, pendants, regulators, sockets, light fitting etc for reuse or removing from site and making good disturbed surface of walls, floors etc.complete all as specified and directed.

Taking down of old Submain wiring any type including batten/ conduit/ casing at any indicated situation complete all as specified and directed.

Taking down of Old MCB DB any type any size including MCCB/RCCB/MCBs and disconnecting the serviceable MCBs and keeping in safe custody for reuse at site or removal from site complete all as specified and directed.

M&L for concealed type point wiring with 1.50 Sq. mm (nominal area) FRLS-H PVC insulated and unsheathed, multi stranded copper conductor cable 1100 Volts grade, single core, laid in and including PVC conduit complete with all fittings and accessories, fixed to walls/ceiling, including mild steel terminal boxes 1.25 mm thick conforming to IS-5133 (Part-I) with 3.0 mm thick plastic laminated sheet top cover (ISI Marked) for mounting switches/ regulator /bell push etc and including 1.50 Sq. mm (nominal area) FRLS-H PVC insulated and unsheathed multi stranded copper conductor cable 1100 Volts grade, single core, earth continuity conductor connected to common earth dolly, for one light point /bell point/ ceiling fan/exhaust fan point controlled by one way switch complete all as specified and directed. (NOTES: - (i) Where tube light fitting is to be fitted/suspended, CI Circular boxes shall be provided with the PVC Pipes in the ceiling & the unit rate shall be deemed to be included for the same. (ii) Cost of cutting chases for concealed wiring shall be deemed to be inclusive in the quoted rates. No claim in this regard shall be entertained at a later stage)

All as per item No. 153 above but for one 5 amps switch socket outlet on same board controlled by another switch, complete all as specified and directed (concealed type point wiring with terminal box).

All as per item No. 153 above but for one 5 amps switch socket combination on independent board, complete all as specified and directed (concealed type point wiring with terminal box).

All as per item No. 153 above but using 2.5 sqmm single core multi stranded copper conductor FRLS-H PVC insulated and unsheathed, cable for 3/6 pin 15 Amp socket outlet controlled by one switch on independent board with and incl 2.5 sqmm green FRLS-H PVC insulated and unsheathed, copper conductor as continuous earth wire with lugs complete all as specified and directed (concealed type point wiring with terminal box).

M&L for concealed type point wiring with 1.50 Sq. mm (nominal area) FRLSH PVC insulated and unsheathed, multi stranded copper conductor cable 1100 Volts grade, single core, laid in and including PVC conduit complete with all fittings and accessories (except terminal box and laminate cover), fixed to walls/ceiling, for mounting MODULAR TYPE switches/ regulator /bell push etc and including 1.50 Sq. mm (nominal area) FRLSH PVC insulated and unsheathed multi stranded copper conductor cable 1100 Volts grade, single core, earth continuity conductor connected to common earth dolly,.complete all as specified and directed. for one light point / bell point/ceiling fan/exhaust fan point controlled by one way switch. (NOTE :- (i) Where tube light fitting is to be fitted/suspended, CI Circular boxes shall be provided with the PVC Pipes in the ceiling & the unit rate shall be deemed to be included for the same. (ii) Point wiring shall be measured from switch board/DB to outlets only. Main circuit wire of the switch board/DB shall be measured and paid seperately as sub main wiring of required size depending upon the load of that switch board. (iii) Quoted rate shall be exclusive of the cost of terminal box and laminate cover which shall be measured seperately.

All as per item No 157 here-in-before but for one 5 pin 5/6 amp socket out let point in the same switch board of light points. (except terminal box and laminate cover), fixed to walls/ceiling, for mounting MODULAR TYPE switches

All as per item No 157 here-in-before but for one 5 pin 5/6 amps multisocket outlet point in independent board (concealed wiring) (except terminal box and laminate cover), fixed to walls/ceiling, for mounting MODULAR TYPE switches

All as per item No 157 above but using 2.5 sqmm PVC insulated unsheathed multi strand copper cable (1100 V) FR for line conductor and 1.5 Sqmm PVC insulated unsheathed multi strand copper cable (1100 Volts) for earth continuty wire for one 15/16 amp multi socket out let independent. (concealed wiring) (except terminal box and laminate cover), fixed to walls/ceiling, for mounting MODULAR TYPE switches

S&F switch piano flush button AC 230 V Single pole 5/6 Amp one way complete all as specified and directed.

S&F socket outlet 2-in-1, 3 pin, 6 Amp AC 230 Volts flush type complete all as specified and directed.

S&F switch socket combination, 5 pin, 6 Amp AC 230 Volts flush type complete all as specified and directed.

S&F switch socket combination 2 in 1, 3 pin, 6 and 16 Amps flush type universal complete all as specified and directed.

S&F socket outlet 6/16 Amps, 6 in 1, flush type complete all as specified and directed.

S&F switch piano flush button AC 230 V Single pole 15/16 Amp one way complete all as specified and directed.

S&F ceiling rose surface, polycarbonate/bakelite, three terminals complete all as specified and directed.

S&F electronic type stepped speed regulator, 100 watts, AC 230 Volts for ceiling fan, complete all as specified and directed.

S & F Modular Switch 1 way, 6 Amps, 1 module

S & F Modular Switch 1 way, 16 Amps, 1 module

S & F Modular Socket 6 Amps, 2/3 pin combined, 2 module

S & F Modular Socket 6/16 Amps, 2/3 pin combined, 2 module

S & F Modular Fan step regulator, 120 watt, 2 module

S&F Modular White cover plate with frame 3 module

S&F Modular White cover plate with frame 4 module

S&F Modular White cover plate with frame 6 module

S & F Modular type Metal Flush box 3 module

S & F Modular type Metal Flush box 4 module

S & F Modular type Metal Flush box 6 module

S&F surface mounted LED luminaire, 1 X 20 Watt in aluminium housing, operating voltage 180-270 V, with acrylic/polycarbonate difuser & integrated constant current electronic driver complete with all other accessories internally prewired and including connecting up with three core flexible copper wire of suitable size complete all as specified and directed. complying with the following specifications:- (a) minimum efficacy 110 lumen/watt (b) CRI not less than 80, (c) THD < 20% (c) having in built short circuit and surge protection (d) colour temperature not less than 5700 degree K (e) life not less than 25000 hours of operation

-ditto- as per Item No. 133 but of 1 X 9/10 Watt capacity in polycarbonate housing with lumen output not less than 105 lumen per watt

S&F in repair steplight, wall recessed, 3 watts, in die cast alumnium housing with inbuilt driver incl necessary electrical connection with suitable size copper flexible wire complete all as specified and directed. (Make: Philips, Model : 34152 / Jaquar, Cat No: LFTL01S003XW)

S & F in repair LED wall mounted spot focusing light fitting 4 watt, colour temperature 2700K, mounted on wall connected with insulated unsheathed flexible copper wire of suitable size complete all as specified and directed. (Make : Philips, Cat No. 56240/31 or equivalent model in other makes specified in tender)

S&F in repair LED flexi strip of required, IP 20 ingress protection with wide viewing angle of 120° with 24/25W LED 6000K including seperate driver and connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F recess mounted LED flat panel luminaire, suitable for 300 mm x 300 mm snap grid ceiling, , in powder coated CRCA housing , having glare free diffuser, operating voltage 180-270V, with constant current electronic driver complete with all accessories with and including 15 Watt LED and including all accessories, mounting frame etc and connecting up with three core flexible copper conductor wire of adequate size complete all as specified and directed and complying with the following specifications:- (a) minimum efficacy 105 lumen/watt (b) CRI not less than 80, (c) THD < 20% (c) having in built short circuit and surge protection (d) colour temperature not less than 5700 degree K (e) life not less than 25000 hours of operation

S&F in repairs recess mounted slim-fit downlighter, round or square, having glare free frosted diffuser, operating voltage 180-270V, with constant current electronic driver complete with all accessories with and including 06 Watt LED and including all accessories, mounting frame etc and connecting up with three core flexible copper conductor wire of adequate size complete all as specified and directed and complying with the following specifications:- (a) minimum efficacy 105 lumen/watt (b) CRI not less than 80, (c) THD < 20% (c) having in built short circuit and surge protection (d) colour temperature not less than 5700 degree K (e) life not less than 25000 hours of operation (f) Weather protection: IP20

S&F in repairs recess mounted slim-fit downlighter, round or square, having glare free frosted diffuser, operating voltage 180-270V, with constant current electronic driver complete with all accessories with and including 15 Watt LED and including all accessories, mounting frame etc and connecting up with three core flexible copper conductor wire of adequate size complete all as specified and directed and complying with the following specifications:- (a) minimum efficacy 105 lumen/watt (b) CRI not less than 80, (c) THD < 20% (c) having in built short circuit and surge protection (d) colour temperature not less than 5700 degree K (e) life not less than 25000 hours of operation (f) Weather protection: IP20

S&F in repairs LED Street Light/Bldg Security light fitting, 25 Watt, 240 Volts, in pressure die cast aluminium housing with lens and toughened glass cover with integrated constant current electronic driver, having ingress protection of IP 66 and impact resistace of IK 07 complete all as specified and directed and complying with the following specifications:-. (a) minimum efficacy 105 lumen/watt (b) CRI not less than 70, (c) THD < 10% (c) having in built short circuit and surge protection upto 4 kV (d) colour temperature not less than 5700 degree K (e) life not less than 50,000 hours of operation (f) Power factor > 0.95 (NOTES: (1) List of approved makes has been provided in particular specifications. Contractor shall ensure that luminaire provided comply with the aforesaid specifications. No claim shall be entertained during currency of work.. (2) Quoted rate is deemed to be inclusive of dismantling of existing bracket. (3) Wire for electric connection of new fitting and new GI pipe bracket shall be measured & paid separately.

S&F in repair decorative wall recessed luminaire with SMD LED as light source, 6-7 watts, with inbuilt driver minimum IP 65 grade protection incl necessary electrical connection with suitable size copper flexible wire complete all as specified and directed. (Make: HAVELLS, Model : Radiant Neo / CROMPTON, Model: Beacon / HALONIX, Cat No: HLOSTL-38-06-CW / SURYA, Model: Diya) (NOTES: Wire for electric connection of new fitting shall be measured & paid separately.

S & F in repair decorative spike landscape light using LED as light source, 09 watt complete all as specified and directed. (Make : HAVELLS, Model: LYCUS / BAJAJ, Model: SPYKZ / HALONIX, Cat No: HLOSPL-02-09-CW or equivalent model in other makes specified in tender) (NOTES: Wire for electric connection of new fitting shall be measured & paid separately.

S&F in repairs LED Flood Light fitting, of 60 watt capcity, in high pressure die cast aluminium housing with prismatic polycarbonate modular secondary lens optics with integrated constant current electronic driver and toughened glass cover, IP66 grade ingress protection, impact resistance IK07 complete all as specified and directed and complying with the following specifications:-. (a) minimum system efficacy 120 lumen/watt (b) CRI not less than 70, (c) THD < 10% (d) Power factor not less than 0.90 (e) having in built short circuit and surge protection upto 4 kV (f) having 10 KV external surge protection (g) colour temperature not less than 5700 degree K (h) life not less than 50000 hours of operation (NOTES: (1) List of approved makes has been provided in particular specifications. Contractor shall ensure that luminaire provided comply with the aforesaid specifications. No claim shall be entertained during currency of work.. (3) Wire for electric connection of new fitting shall be measured & paid separately.

S&F in repairs PVC insulated multistranded copper conductor wire, 2.5 sqmm 3 core, round flexible for connection of light fittings complete all as specified and as directed.

M&L for sub main wiring with 4 run of FRLS-H PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 10.0 sqmm alongwith one run of FRLS-H PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 10.0 sqmm as earth continuity conductor drawn through and including PVC casing-caping of suitable size, surface type complete all as specified and directed. (NOTE : Five runs of single core 10.0 sqmm cable & one run of PVC casing capping shall be measured as one unit)

All as per Srl. Item No. 193 above but with two runs of 6.0 Sqmm cable and one run of 6.0 Sqmm as earth continuity conductor in PVC casing capping (NOTE : Three runs of single core 6.0 sqmm cable & one run of PVC casing capping shall be measured as one unit)

All as per Srl. Item No. 193 above but with two runs of 4.0 Sqmm cable and one run of 4.0 Sqmm as earth continuity conductor in PVC casing capping (NOTE : Three runs of single core 4.0 sqmm cable & one run of PVC casing capping shall be measured as one unit)

S&F TPN DB, IP 43 protection, double door (premium quality), 415 volts, 4 way (8+12), with 100 Amps copper bus bar for each phase complete all as specified and directed. (MAKE : L&T, Cat No. DBTPN004DD / LEGRAND, Cat No: 507670 / SCHNEIDER, Cat No. A9HTND04 / ABB, Cat No: E-SHDB M4 / PANASONIC, Cat No: BQS 304H / HAGER, Cat No: VYT04DH)

S&F, Double Door, Sheet Metal Enclosure for DBs (Premium Quality), for mounting of MCB for 240 Volts, 8 way, with 100 Amps rated copper bus bar, Single Pole & Neutral, complete all as specified and directed. (MAKE : L&T, Cat No. DBSPN008DD / LEGRAND, Cat No: 507611 /ABB, Cat No. E-SHC M 8 / SCHNEIDER, Cat No. A9HSND08 / HAGER, Cat No: VYS08D)

S&F SPN DB, IP 43 protection, double door (Premium Quality), 240 volts, 4 way, with 100 Amps copper Bus Bar complete all as specified and directed. (MAKE : L&T, Cat No. DBSPN004DD / LEGRAND, Cat No: 507610 / ABB, Cat No. E-SHC M4 / SCHNEIDER, Cat No. NBKRENSNDD04 / HAGER, Cat No: VYS04D)

S&F MCB (premium quality), 'C' series, TPN, 415 volts, 63 Amps, breaking capacity 10KA complete all as specified and directed. (MAKE : L&T / LEGRAND / SCHNEIDER / ABB / PANASONIC / HAGER)

S&F MCB (premium quality), 'C' series, SPN, 32 Amps, breaking capacity 10KA complete all as specified and directed. (MAKE : L&T / LEGRAND / SCHNEIDER / ABB / PANASONIC / HAGER)

S&F MCB (Premium Quality), 'C' series, single pole, 6 to 32 Amps, breaking capacity 10KA complete all as specified and directed. (MAKE : L&T / LEGRAND / SCHNEIDER / ABB / PANASONIC / HAGER)

S&F in repair MODULAR MCB protected power unit with one 25 Amps socket with 3 pin plug top and including 01 No MCB, DP, and starter 25 Amps ratings with six module plate and flush metal GI box and electrically connected complete all as specified and directed. (MAKE : HAVELLS, Cat No. DHDUCDP0253025 / NORTH WEST, Cat No: ACPU6M-BT or equivalent model in ABB / CRABTREE / HAGER / SCHNEIDER / LEGRAND) (NOTE : Enclosure & MCB shall be same manufacturer. Cost of MCB is deemed to be included in the quoted rate)

S&F in repairs single pole enclosure with two pin and earth plug and socket complete with one SP MCB, 20 Amps, 'C' Curve, 10 KA including all accesories complete all as specified and directed. (MAKE OF ENCLOSURE: LEGRAND, Cat No. 5078 10 / L&T, Cat No. DBMPS120SD / SCHNEIDER, Cat No: A9HMS220 / ABB, Cat No. NSYN8690SGKSP20 / C&S, Cat No: CSDBPSSPN020 / BCH, Cat No: BCHPSDBSPN20 / HPL, Cat No: MDBSP20 / HAGER, Cat No: VYA220Cor equivalent model in Havells / Indo Asian ) (NOTE : Enclosure & MCB shall be same manufacturer. Cost of MCB is deemed to be included in the quoted rate)

Hanging only ceiling fan, any sweep, connecting up including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 1.0 Sq mm, 3 core, 1100 Volts grade, from ceiling rose/ connector to fan complete all as specified and directed. (NOTE: Geyser will be issued under Schedule 'B' as free for fixing. Old fan, if any taken down, shall be deposited by contractor in MES storeyard)

Supply and fixing ventilating fan, 250 mm sweep, made of sturdy engineered plastic with louver shutter, 230 Volts, 50 Hz, connecting up including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 1.50 Sq mm, 3 core, 1100 Volts grade, from ceiling rose to fan complete all as specified and directed. (MAKE : HAVELLS, Model : Venti Air DX / CROMPTON, Model : Brisk Air / USHA, Model: CRISP AIR or equivalent model in BAJAJ / ORIENT / POLAR)

Installation, testing and commissioning of heater water storage type electric geyser (any type) 25 ltrs capacity including necessary connections complete all as specified and directed. (NOTE: Geyser will be issued under Schedule 'B' as free for fixing. However, quoted rate shall be deemed to be inclusive of one 16 Amps plug top)

S&F IP 54 rated wall light with die cast aluminium housing and opal white polycarbonate diffuser, 1 X 8 Watt, 3000K colour temperature complete all as specified and directed. (MAKE: JAQUAR, Model : WOODY or equivalent model in other makes specified in tender)

M&L for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6.0 mm thick buried directly in ground vertically to a depth not less than 2.25 meter deep below ground level with top edge earth plate at a depth not less than 1.5M below normal ground level connected to galvanized steel earth wire 4 mm dia (upto 7.5 metres) by means of bolts, nuts check nuts and washers of galvanized steel and connected to main switch board or main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 45 cm x 45 cm x 5 cm reinforced with 8 mm dia. TMT bars @ 150 mm centre to centre both ways, with one handle for lifting made out of 8 mm dia MS bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 40 mm bore galvanized steel tubing medium grade for protection of earth lead connection, necessary excavation and earth work in any type of soil and including necessary testing and dismantling of existing unsv earthing complete all as shown in Figure 15A of IS 3043 :1987, complete all as specified and directed.

S.K. TRADERS

dutta and dutta

MARUTI ENTERPRISES

RAY STANDARD ENGG CO.

ARJUN DAS VALECHA

RAJ ENTERPRISE

MS AP CONSTRUTION AND CO

GHOSH ENTERPRISE