Renovation of toilet at Govt. School, Simni under Swacch Bharat Abhiyan CSR and SD

Demolition below G.L upto 1.50 metres depth including stacking of serviceable materials and disposal of unserviceable materials within 20 metres lead and including cutting the neceesary reinforcement and separating from R.C.C./R.B. work.

Extra over time No. 20030000 for every additional 1.5 metres depth.: RCC work.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead

Brick work using common burnt clay building bricks in foundation and plinth in Cement Mortar 1:5 Second Class Brick (1 Cement : 5 Sand)

Extra for brick work in : Super-structure above plinth level upto floor two level (Second Class Bricks).

Providing and laying cement concrete work 1:1.5:3 (1 cement :1.5 sand :3 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work and rein-forcement for reinforced concrete work in Lintels, beams girders bress-umers and cantilevers upto floor two level :

Providing form work with steel plates 3.15mm. thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuutering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below suppor-ting floor to ceiling not exceeding 4 Mtrs. and removal of thesame for in situreinforced concrete & plain concrete work in:Flat surfaces such as soffits of suspended floors, roofs, landings and the like. Floors etc.upto 200mm. in thickness.

Providing Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete upto floor two level :

6mm Cement plaster to ceiling In Cement Mortar 1:4(1 Cement: 4 Sand)

15mm Cement plaster in single coat on the rough side of for interior plastering upto floor two level includ-ing floor two level including brick/ concrete/ stone walls for interior plastering upto arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth. Cement Mortar 1:6 (1 Cement: 6 Sand).

Applying one coat of distemper primer of approved brand and manufacture on wall surfaces after thoroughly brushing the surface free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

Distempering (two coats) with oil bound washable distemper of appr-oved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer

Finishing wall with water proofing cement paint ofapproved brand and manufactureand of required shade on undecorated wall surfaces(two coats) to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials.

Painting two costs (excluding priming cost on new steel and other metal surfaces eith enamel paint brushin to give an even shade including cleaning the surface of all dirt,dust and other foregin matters Enamel paint other than white

Providing and laying cement concrete 1:2:4 (1 cement:2 Sand:4 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work in Foundation and plinth

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Steel work welded in built up sections, trusses and framed work, including cutting , hoisting , fixing in position and applying a priming coat of red lead paint. In gratings framed guard bars, ladders, railling, brackets and similar works.

Providing and fixing M.S. pressed butt hings with necessary screws. (Copper oxidised) 100x58x1.90mm

Providing and fixing oxidised M.S. tower bolts (barrel type) with necessary screws etc. complete 150x10mm

Providing and fixing oxidized M.S. sliding door bolts with nuts and screws etc. complete. :250x16 mm

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame o f 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing brass bib cock of approved quality : 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions 45 cm length 15 mm nominal bore

Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqm including filling the joints with approved adhesive complete 100mm dia pipes

Providing and fixing on wall face unplasticised - PVC moulded Single tee without door for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.110x110x110 mm

Providing and fixing on wall face unplasticised - PVC bend 110 mm dia for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion

Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqm including filling the joints with approved adhesive complete 75mm dia pipes

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour.15 mm nominal bore, weighing not less than 32 gms

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete. 15 mm nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.Internal work - Exposed on wall15 mm dia nominal bore

Providing and fixing brass stop cock of approved quality 15 mm nominal bore

AMAN CONSTRUCTION COMPANY

SHAM LAL SHARMA