PROVN OF TRAINEES ACCN, BATHROOM CUM TOILET BLDG NO. P 348 WITH 2 X TOILET WITH CHAIN LINK FENCING, DRINKING POINT, WASHING POINT WITH SUMP NEAR CHAIN LINK FENCING AT SCE NEW CANTT ALLAHABAD

Amount

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, laying of cable, CI pipe line, etc. n exc 10 Sqm on plan and n exc 1.5 m in depth and getting out complete all as specified and directed.

M & L for cement concrete type C2 1:3:6, 40 mm graded aggregate in foundations, filling and mass concrete using 40 mm graded aggregate complete all as specified and directed

Removing surplus excavated soil to a distance n.exc 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above starting point all as specified & directed

Returning, filling in, soil obtained from excavation including spreading, levelling, watering and well ramming in layers n.exc 25cm thick all as specified & directed.

Use & waste of formwork flat to sides of rough finished surface of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed

Use & waste of formwork to sides of rough finished surface of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed

Use & waste of formwork to rough finished sides and soffits of floor or roof beams, beam haunching, girders, bressumers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed

Use & waste of formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed.

Use & waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed

M & L for Reinforced cement concrete design mix M-25 using 20 mm graded stone aggregates in foundations, footing, plinth beams, bases for columns and mass concrete complete all as specified and directed. Note:- Reinforcement to be measured & paid separately under respective item.

M & L for Reinforced cement concrete design mix M-25 (using 20 mm graded stone aggregates) in columns, pillars, posts & struts complete all as specified and directed. Note:- Reinforcement to be measured & paid separately under respective item.

M & L for Reinforced cement concrete design mix M-25 using 20 mm graded stone aggregates in lintels over 1.5m clear span, beams and cantilevers complete all as specified and directed. Note:- Reinforcement to be measured & paid separately under respective item.

M & L for Reinforced cement concrete design mix M-25 using 20 mm graded stone aggregates in chajjas complete all as specified and directed. Note:- Reinforcement to be measured & paid separately under respective item.

M & L Brick work with fly ash bricks, straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and directed

M & L for modular brickwork with fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in 1:4 CM complete all as specified and directed

M & L for 25 mm thick damp proof course in cement concrete 1:2:4, type B0 using 12.5 mm graded stone aggregate, horizontal or vertical surfaces including necessary formwork complete all as specified and directed

M & L for Anti-termite treatment by treating the bottom and sides of excavation at the rate of 5 liter of emulsion per square meter of surface area complete all as specified and directed

M & L for Anti-termite treatment by treating the backfill in contact with foundation at the rate of 7.5 liters of emulsion per square meter of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed

M & L for Anti-termite treatment by treating the top surface of filled earth at the rate of 5 liters of emulsion per square meter of surface complete all as specified and directed

M & L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L for Mild steel TMT bars 8 mm to 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping as in stirrups for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M & L for sand filling under floors or in foundation including watering and consolidation complete all as specified and directed.

M & L for 150 micron polythene film in sub base floor complete all as specified and directed.

M & L for 75 mm thick cement concrete type D-2, 1:4:8 40mm graded aggregate complete all as specified and directed.

M & L for Hardcore of gauge 50 mm thick with broken stone n exc. 63 mm, deposited, spread and leveled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for rendering 10mm thick in CM 1:3 on ceiling surfaces of RCC or brick complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces complete all as specified and directed

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying two coats of oil bound distemper over a coat of primer over & including 2 mm thick wall care putty complete all as specified and directed.

M&L for preparation of old decorated/ plastered surface of wall and applying two coats of oil bound distemper complete all as specified and directed.

M&L for preparation of newly plaster surface of wall and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 5489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces including one coat of 3mm birla wall care putty complete all as specified and directed.

M&L for preparation of newly plaster surface of ceiling and applying two coats of white wash complete all as specified and directed.

M & L for dark shade Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface with 15mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed.

M & L for dark shade Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface with 10mm thick backing coat in CM 1:3 in skirting complete as specified and directed

M & L for non skid coloured ceramic floor tiles 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.06 sqm but n exc 0.11 sqm, in floor ,wall etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the surface with 15mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed.

M&L for glazed ceramic coloured wall tiles in vertical surface 450 X 300 X 7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering in 1:4 CM complete all as specified.

S&F in repair prelaminated MDF type board 18/19 mm thick, interior grade, prelaminated on one side with decorative choice lamination and other side balancing white lamination as in Cupboard Shutter / Cupboard shelves with and including external teak wood lipping 6mm thick and 18/19 mm wide fixed with nails on edges complete all as specified and directed.

S&F 30mm width of flaps continuous (piano) hinges, mild steel, bright finish or electro galvanised complete all as specified.

S&F 100 mm hasp & staple safety type of aluminium anodised including bolt to hinges plate and fixed with screws complete all as specified and directed.

S&F hollow MS steel double / single rebated door frame 105x60mm or any other similar works of approved shape and size including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed.

M&L for Laying of 3mm thick APP membrane of (reinforced with non-woven fabric polyester type) (weight not less than 3 kg per Sqm) shall be done using butane torch maintaining 100mm side overlap and 150mm end overlap, sealing all overlaps and bonded to the surface by fusing and bonding torch on method complete all as specified and directed. Note: All water proofing work shall be done as per manufacturer instruction and under supervision of manufacturer technical representative.

Cleaning the dust, dirt and any other foreign material from roof surface and applying a coat of bituminous primer @ 0.40 ltr / Sqm uniformly and primer shall be allowed to dry over night as conforming to IS 3384-1986 complete all as specified and directed.

Supply only Liquid water proofing compound (ISI marked) complete all as specified and directed.

M&L for 10mm thick plaster in CM 1:3, mixed with liquid water proofing compound over concrete surface of roof when concrete is green complete all as specified and directed. Note : WPC to be measured and paid separately under appropriate item.

S&F factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube complete all as specified and directed.

M&L for 40 mm thick flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F of galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks of galvanised wire staples complete all as specified and directed.

M&L preparation of newly wooden surface exc over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

S&F 2nd class hardwood factory made door, 35 mm thick, glazed and skeleton shutters, open rebated and prepared to receive glass gauze etc (with sash bars) edges of framing plain, chamfered or rounded materials and rebated sash bars any number , edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass in door etc or provided with styles and rails as specified in SSR part 1 section 8, clause 8.20 (a) complete all as specified & directed.

S&F 100 mm long mild steel butt hinges, cold rolled, medium weight complete all as specified and directed.

S&F 100 mm long stainless steel butt hinges with steel pin complete all as specified and directed.

S&F 200mm long anodized aluminum barrel tower bolt of extruded section complete all as specified and directed.

S&F 150mm long anodized aluminum handles, fabricated type complete all as specified and directed.

S&F 300mm long, aluminum alloy, anodized aldrop door bolt including fixing clips of sheet, cast or extruded section and fixing bolts and 16mm dia bolt of sliding bolts of extruded sections complete all as specified and directed.

M&L for 75 mm thick cement concrete 1:3:6 type B2 using 20 mm graded stone aggregate in plinth protection finished even and fair including necessary form work and cutting of joints using extra cement etc complete all as specified.

S & F aluminum extruded body section door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed

M & L for treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed.

M & L for PCC type C1 (1:3:6) 20mm graded aggregate in drain along Plinth protection complete all as specified and directed

S & F of aluminum anodized powder coated of approved colour, sliding type three track window or ventilator with sliding shutter and frame with and including aluminum grill, 5 mm thick tinted glass and mosquito proofing net as detailed below including complete all as specified and directed: -(i) Frame made of section size 92 X 31.75 X 1.30 mm as suitable for bottom, top and sides of window. (ii) Shutter for top, bottom and side rails 40 X 18 X 1.29 mm.(iii) Glass 5 mm thick one side reflective glass and other side visible fixed with rubber gasket and aluminum clips of suitable size, 4 Nos. aluminum hold fasts with each window and necessary handles, tower bolt etc. as directed. (iv) Aluminum grill made of 5 mm dia powder coated aluminum section as per design No. DG-102 of make DECO grill or design No. A-103 duly fixed with aluminum section 50 X 20 X 1.5 mm size.(v) Stainless steel wire cloth having 0.36 mm nominal dia of wire and average width of aperture 1.40 mm duly fixed with tined tacks or galvanized wire staples.

S & F Salt glazed stoneware drain pipe grade 'A' 150 mm bore laid in tranches and jointed complete all specified and as directed.

M & L for PCC 1:3:6 type C2 using 40 mm graded aggregate as in bed drain pipes of 150 mm bore including packing under and haunching against the sides of pipes after they are laid and tested complete.

Cutting holes into existing manhole brick wall manhole built in CM, connection new drains making good to pipes and rendering cutting out existing benching for and forming branch channel ( 1/2 round or 3/4 section) in cement concrete (1:2:4) type B1 smooth finished and reforming benching as required for internal dia of pipe 150mm complete all as specified and directed.

S & F in PVC connection 450 mm long, 15 mm size with brass chromium plated nuts complete all as specified.

S&F 15 mm bore GI steel tubing "medium grade" with all fittings and fixed to wall, floor and ceiling etc complete all as specified.

S&F 20 mm bore GI steel tubing "medium grade" with all fittings and fixed to wall, floor and ceiling etc complete all as specified.

S&F angular stop cock with wall flange complete all as specified and directed. Make :Jaquar Cat part OPP-CHR-15053PM or equivalent make as specified in PS.

S&F brass chromium plated shower rose 125mm size complete all as specified and directed.

S&F shower arm 15 mm size, 195mm long with bend of 45degree with flange of PTMT any colour (minimum weight 40gms) completes all as specified and directed.

S&F 15mm stop cock concealed body for but fancy type, chromium plated with long shank and cup (concealed type) complete all as specified and directed.

S&F fancy tap Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed pipe and fixed complete all as specified and directed

S&F bib taps fancy type with crutch or butter fly handle, chromium plated with screwed down, screwed for iron pipe or for brass ferrule ,15mm bore complete all as specified and directed.

S&F in jet nozzle for EWC complete with all fittings complete all as specified and directed.

S&F two way angle cock with wall flange complete all as specified and directed. Make : Jaquar Cat part KUP-CHR-35041PM or equivalent make as specified in PS.

S&F vitreous china wash and basin, white, flat back, size 550 mm x 400 mm fixed on MS bracket including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe, waste fitting, pipe and union complete all as specified and directed.

S&F WC squatting pan “Orissa Pattern” of size 580 x 440mm white with integral foot rest (excluding flushing cistern & flush pipe) including connection to trap and to flush pipes etc and lime concrete bedding complete all as specified in SSR and including 'P' or 'S' trap complete all as specified and directed.

S&F vitreous china Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) including 32mm dia CP coupling, CP urinal spreader with CP pipe up to angle cock, waste pipe etc with all fixing arrangement and pointing around urinal back complete all as specified and directed.

M&L for 500 ltr rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified.

S&F 20mm bore ball valves high pressure of PTMT with epoxy coated aluminum rod & high-density plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm-210 gms) complete all as specified and directed.

S & F 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed.

S&F PVC flushing cistern 10 ltr capacity valve less symphonic action type low level with and including ball valve float & handle, waste pipe & brackets complete set all as specified and directed.

S & F 110 mm bore PVC (SWR) pipes singles socket in any length with rubber ring joints laid in trench or in floor complete.

S & F 110 mm bore PVC (SWR) pipes singles socket in any length with rubber ring joints fixed to wall complete all as specified and directed.

S & F 110 mm bore PVC (SWR) bend any radius complete all as specified.

S & F 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified.

S & F 110 mm outlet dia PVC (SWR) floor trap plain with grating including jointing with solvent cement. Complete.

S & F 110 mm bore PVC (SWR) vent cowl complete all as specified.

S&F in repair PVC waste pipe 32mm dia, 60 cm long for WHB/urinal with cup, complete all as specified.

S & F in repairs 600 mm long tubular towel rail , brass chromium plated of 20 mm dia complete all as specified and directed.

S & F in repairs suitable for 15 mm dia health faucet abs body with 8 mm dia 01 mtr long flexible tube & wall hook complete all as specified and directed.

S & F in repairs PVC (SWR) floor trap plain or multi with stainless steel grating including joining to waste pipe with solvent cement joint dia of outlet 75 mm bore complete all as specified and directed.

S & F Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed

S & F sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

S&F CP angle stop valve or cock of 15mm bore screwed down for high pressure with crutch or butter fly handle ,screwed both end for iron pipes complete all as specified and directed..

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in soft / loose soil complete.

M&L for 75 mm thick cement concrete 1:2:4 type B-2 using 40mm graded stone aggregate as in sub base in Path, hard standing complete all as specified & directed.

M&L for chequered cement concrete tiles with grey cement and no pigments 300mm x 300mm x 22 to 25 mm thick, set, jointed and pointed in neat cement slurry in floors over & including 15 mm thick screed bed or bedding layer in CM 1:6 complete all as specified & directed.

S&F 25 mm bore GI steel tubing 'medium grade' with all fittings, laid in trenches and fixed to wall, floor and ceiling or laid in floors etc complete all as specified.

S&F 40 mm bore GI steel tubing "medium grade" with all fittings, laid in trenches and fixed to wall, floor and ceiling or laid in floors etc complete all as specified.

S & F for 40 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

M & L for cement concrete type D2 1:4:8 (40 mm graded aggregate) in foundations, filling , sub base of floor and mass concrete (40 mm graded aggregate ) complete all as specified and directed.

M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate as in lintel band at any height complete all as specified and as directed.

M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate as in slabs supported on walls, roof beams etc and the like, complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exceeding 10cm but not exceeding 20cm wide complete all as specified and as directed

M&L for 5 mm thick rendering in CM 1:3 on ceiling surface plaster complete all as specified and as directed.

M&L for preparation of new plastered surface of wall and applying two coats of cement base paint over & including one coat of primer complete all as specified and directed.

M&L for preparation of old decorated / plastered surface of wall and applying two coats of cement base paint complete all as specified and directed.

M & L for non skid coloured ceramic floor tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floor ,wall etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the surface with 15mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed.

S & F factory Made Solid PVC moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain moulded PVC Sheet Polyurethane painted on the front face & 2mm prelam PVC Sheet on back face complete all as specified and directed.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

M&L for preparation of new steel surfaces exceeding 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F 3mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and directed.

S & F in PVC connection 600 mm long, 15 mm size with brass chromium plated nuts complete all as specified.

S&F in repair over head shower 125 mm dia, round shape single flow (ABS body chrome plated with gray face plate, with rubit cleaning system, with suitable shower arm including all accessories, fancy type, complete all as specified and directed.

S&F fancy type Pillar tap 15mm bore, cast copper alloy with capstan heads, chromium plated, screwed down, high pressure with long shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S & F for 25 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling wall and ceiling boards or insulation boards, any thickness, any description, including cover fillets complete all as specified and directed.

Demolition of brickwork masonry built in lime or cement mortar including all quoins arches , pillars etc. but including concrete articles complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) area exc.1.5 Sqm each not exceeding 4.00 Sqm each complete all as specified and directed.

M&L for factory made uPVC white colour sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+/ - 0.2mm), window profile with hollow section with multi chamber. Frame of size 88mm x 52mm, sliding sash of size 42mm x 67mm, sliding mesh Sash of size 42mm x 57mm, sliding interlock (One vertical length in each shutters) of size 45.5mm x 28mm, Glazing bead 24.5mm x 16mm will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2 +/ - 0.2mm thick galvanised steel frame of size 30mm x 18mm, 2 nos, sliding sash 30mm x 18mm, sliding mesh sash 26 mm x 10mm profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and required accessories complete all as specified and directed. Note: (i) The unit rate quoted by contractor shall be deemed to include all other connected accessories. (ii) Area of glass shall be measured & paid separately under relevant item. (iii) Net Opening will be measured for payment purpose.

S & F for anodized aluminum grill (anodized transparent or dyed to required shade according to IS 1868 with minimum anodic coating of grade AC 15 of approved design/pattern, with approved standard section and fixed to the existing window frame with CP brass/stainless steel screws @ 200mm center to center, including cutting to grill to proper opening for fixing and operation of handles and fixing approved anodized aluminum standard section around the opening complete all as specified and directed.

S & F for repair to 5mm thick Prelam PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining, Insulated PVC Wall Lining, and Solid PVC Partitions inclusive of Solvent cement and fixing at site complete all as specified and directed.

S& F for repair to 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed.

Providing and fixing Powder coated aluminum (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminum snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as specified and directed.

S& F for in repair of to 4mm thick non asbestos fiber cement building boards fixed or laid/ inserted to timber/GI/aluminum framework with screws over anodized aluminums snap grid frame work for false ceiling with Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long complete all as specified all as specified

S&F 4.8 mm thick sheet glass ordinary quality in square n.exc 0.5 Sqm in each pane new door / window shutter complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 using 12.5 mm aggregate stone aggregate as filled etc complete all as specified and directed by EIC.

S & F PVC (SWR) gully trap 125 / 110 mm, setting and jointing with solvent cement complete all as specified and directed.

S & F grating doom 100mm dia of PTMT (Minimum weight 25gms)complete all as specified and directed.

M&L for machine cut kota stone slab flooring 18-20 mm thick including 15 mm thick screed bed of (1:6) or bed jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as specified and directed.

M & L for Granite (of any type) work (table rubbed and polished) including the screed bed in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. including with 15mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed.

Excavating in post holes (or similar holes) in soft / loose soil each not exceeding 0.5cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm ,watering and removing surplus soil to a distance not exceeding 50m and making good surface complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Form work to sides & soffits of lintels over 1.5m clear span, floor or roof beams, cantilevers, etc for rough finished flat surfaces of concrete complete all as specified and directed.

M & L for PCC 1:2:4 type B0 using 12.5 mm graded aggregate as in roof, lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

S & F for Fe- 290 Gde E- 165 Rolled mild steel in Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed

Supply only chain link fencing of size 100mmx100mm,4mm dia complete all as specified and directed

S & F Framed work of Fe- 290 (Gde E- 165)as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed

S & F for Mild steel round bars Fe-410-W (Gde.E-250) Quality-A or Fe 290 (Gde - E-165)10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for grinding / mirror polishing ( wax polish) on existing kota stone flooring complete all as specified and directed.

M&L for rounding to edges of stone slab one edge, such as in steps, cooking platform and other similar situation complete all as specified and directed.

S&F vitreous china white wash down water closet pan 250 mm x 585 mm x 415 mm wall hung including fixing bolts, UF soft close seat cover, hinging device complete all as specified and directed. Make:- Jaquar Cat Part No. ONS-WHT-10853S300UFSM or equivalent make as specified in P.S.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self-tapping screws complete all as specified and directed.

S & F steel work in tubular trusses, purlins, rafter, column where connected common rafter and running rails fixed with angle cleat or other common plates including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St.-240 complete all as specified and directed.

S&F rolled mild steel conforming to Gde Fe 290 (Gde E-165) (Plain or chequred) , joist, channel, angle or tee sections, fixed independently, without connecting plates, etc complete all as specified and directed.

M&L for MS screw bolts 11 to 15 mm dia (machine made) with hexagonal or square heads at one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and hexagonal or square nut exceeding 15 cm and not exceeding 22.5 cm long complete all as specified and directed.

M&L for point wiring with FRLS PVC insulated unsheathed stranded copper conductor cable 1.5 Sqmm (nominal area) 1100 volts grade, along with one single run of same size and type of copper wire as continuous earth wire to common earth dolly drawn in and including non metallic PVC rigid, medium grade concealed conduit with all fixing accessories of 20mm dia, using new MS sunk terminal boxes of thickness not less 1.2mm, new 3mm thick laminated sheet cover with brass screw and cup washers with all accessories and making good to disturbed conceal surfaces complete all as specified and directed for the following :- Note:(a) Colour code of wire shall be strictly followed , Red for Phase , Black for neutral and green for earth wire (b) The unit rate quoted is deemed to be inclusive of cost of cutting chases in wall for providing concealed conduit and making good to match with existing finish/surface.

One light/fan/bell point controlled by one switch

One point for socket outlet 5 amps on independent board but not below the switch board in same vertical plane.

One point for socket outlet 5 amps on independent board but below the switch board in same vertical plane

One point for socket outlet 5 amp same board.

One bell/ buzzer point controlled by one push button on the same board with other switches or independent

All as per srl item No. 152 above but for one 3 pin socket outlet 15 amps, independent, with cables 2.5 sqmm size on independent board 2.5 Sqmm earth wire complete all as specified and directed.

All as per srl item No. 152 above but for one 3 pin socket outlet 15 amps, independent, with cables 4.0 sqmm size on independent board 4.0 Sqmm earth wire complete all as specified and directed.

S&F ceiling rose surface type bakelite 65 X 50 mm three terminal complete all as specified and directed.

S&F call bell, ding dong type, AC, 230 V, single pole complete all as specified & directed.

S&F switch piano, modular flush type 5 amps, single pole, one way 230 volt complete all as specified & directed.

S&F switch piano, modular flush type 15 amps, single pole, one way 230 volt complete all as specified & directed.

S&F socket outlet modular type suitable for 3/ 5 pin , 5 Amp, 230 volt complete all as specified & directed.

S&F socket outlet modular type suitable for 6 pin , 3 module, 5/15 Amp, 230 volt complete all as specified & directed.

S&F switch piano, flush type 5 amps, single pole, one way 230 volt complete all as specified & directed.

S&F socket outlet suitable for 3/ 5 pin , 5 Amp, 230 volt complete all as specified & directed.

S&F switch piano, flush type 16 amps, single pole, one way 230 volt complete all as specified & directed.

S&F socket out let 2-in-1, 3 pin, 5/6 & 15/16 amp flush type complete all as specified & directed.

S&F bell push modular flush type 5 amp 230 volt complete all as specified & directed.

S&F fan regulator, modular type, 5 stepped, FSC type 2 module, single phase 230 volt including connection complete all as specified & directed.

S&F Modular cover plate with frame 3 module complete all as specified & directed.

S&F Modular cover plate with frame 4 module complete all as specified & directed.

S&F Modular cover plate with frame 6 module complete all as specified & directed.

S&F TV socket outlet, modular type, single with pressed steel sunken box with top cover & base frame complete all as specified & directed.

S&F 25 mm dia rigid non metallic PVC conduit exclusive of boxes (Junction / terminal) but inclusive of all tees, bends, bell mouth tube ends and fixing accessories such as couplers, lock nut, saddles, pipe hook etc complete all as specified & directed.

S&F angle/ lamp/ batten type holder insulated body with back plate suitable for light point complete all as specified and directed.

S&F sheet metal enclosure for MCB's 240 volt 8 way single pole and neutral with 200 amps rated busbar, double door on wall with and including suitable flat iron clamps duly grouted/ fixed flush in the wall complete all as specified and directed.

S & F DB with single phase & neutral MCB Distribution Box of 8 Way, double door of protection grade IP 43 in fine powder coated, matt finish with best CRCA sheet, fitted with shrouded neutral, insulated pin type copper bus bar, Din rail, earth bar confirming to IS 13032 & 8623 complete all as specified and directed.

S&F MCB SP 40/63 Amps 'C' series, breaking capacity 10 KA of rating & making connection complete including taking down complete all as directed.

S&F MCB single pole, 6 to 32 amps rating, 240 volts, 'C' series, 10 KA breaking capacity & making connection including taking down complete all as specified and directed.

S&F MCB single pole & neutral, 32 amps rating, 240 volts, 'C' series, 10 KA breaking capacity & making connection complete all as specified and directed.

M&L for concealed submain wiring using FRLSH PVC insulated, unsheathed stranded copper conductor cable two single core of size 6.0 Sqmm of voltage rating upto and including 1100 volts drawn in and including PVC concealed conduit of dia not less than 20 mm dia with all fittings and accessories along with one run of PVC insulated unsheathed stranded copper conductor of size 6.0 Sqmm as earth continuity conductor for 8 way DB complete all as specified & directed. Note:- (i) Two runs of single core PVC cable with one run of earth conductor and conduit shall be measured as one length. (ii) The cost for cutting, chases required shall deemed to be included in the quoted unit rate.

S&F in replacement surface /wall mounted light fitting in CRCA powder coated white housing with pre wired suitable for single T8 LED tube along with supply and fixing one number LED tube in polycarbonate housing of nominal wattage - 18 Watt, Lumen out put - 2100 Lm, Colour Temp - 6500 Kelvin, Size & Length - G13/ T8/ 4 Feet with integral/in built driver, having short circuit and surge protection including making connection with two core PVC insulated, sheathed copper conductor cable of size 23/0.0076 complete all as specified and directed.

S & F in replacement LED light fitting 10 watt mirror type with high output with opal diffuser 2 ft 230 V AC with driver holder and LED lamp including making connection with three core PVC flexible insulated, sheathed copper conductor cable complete all as specified and directed.

S & F in replacement LED 10 Watt bulk head fitting with high output with opal diffuser 230 V AC with driver holder and LED lamp including making connection with three core PVC flexible insulated, sheathed copper conductor cable complete all as specified and directed.

S & F in replacement LED light fitting with box type ultra slim linear LED lighting fixture with co- extruded polycarbonate body environmental friendly, energy efficient tube light complete with all accessories internally pre- wired and including LED lamp 20 watt 01 No and connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.

S&F surface /wall mounted light fitting in CRCA powder coated white housing with pre wired suitable for single T8 LED tube along with supply and fixing one number LED tube in polycarbonate housing of nominal wattage - 18 Watt, Lumen out put - 2100 Lm, Colour Temp - 6500 Kelvin, Size & Length - G13/ T8/ 4 Feet with integral/in built driver, having short circuit and surge protection including making connection with two core PVC insulated, sheathed copper conductor cable of size 23/0.0076 complete all as specified and directed.

S&F energy efficient LED light of 10 Watt of length - 02 Feet long having minimum 1150 Lumen output, wide voltage protection range 140-270 Volt AC housed in extruded aluminum housing (enhances safety) with high quality polycarbonate diffuser including making connection with two core PVC insulated, sheathed copper conductor cable of size 23/0.0076 complete all as specified and directed.

S&F of Decorative, wall mounting, champagne gold finish fixture with plastic body suitable for 10W retrofit LED complete in specified and as directed.

S&F Exhaust fan 300 mm sweep metallic body Range complete and shutters including required length and size of copper stranded conductor for connection from ceiling rose to connector of fan with provision of making hole in wall complete with grouting of nuts, bolts and washers and all other accessories required for fixing of fan including testing complete all as specified and directed.

S&F ceiling fan with down rod, fan connector/ fan hook, 1200mm sweep, 240 V AC, Energy efficient, 5 star rating with 3 Blade and connecting up including provision of three core PVC insulated multi stranded flexible copper conductor cable of size 1.5 sqmm copper wire from ceiling rose to fan of length not less than 0.5 mtr. all as specified & directed.

S&F vertical /horizontal water heater storage type, electrically operated of capacity 25 litres, BEE 5 star rated ABS/ steel body and inner tank made with stainless steel duly thermal insulated with 2 KW heating element complete with and including vent pipe , fusible plug, safety valve, earth connector including CP connection 450 mm long for hot and cold water outlet supply and electric connection all as specified and directed. Make:- Havells (Cat Part No (Quatro)GHWEQTTIB025 , Crompton (Cat Part No.Matteo 25) , Bajaj (Cat part No. MAJ 25GL (New) as approved by GE.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete including bracket for street light made out of 40 mm bore GI pipe medium grade not less than 1.2 mtr length bent at 120 degree to shape fixed on pole/wall with and including 50x6mm FI clamps = 02 Nos with nut bolts, washers including painting of clamps with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Supplying and fixing smart single phase two wire dual source prepaid energy meters BIS 15884 marked in existing meter board / floor panels with pre payment capacity touch keypad based digital having current range 10-60 Amp 240 Volt accuracy class 1.0 along with parallel home display split unit with inbuilt load control switch containing provision for TOD and RTC all as specified.

M &L for Earthing complete with GI earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25M deep below normal ground level) with top edge of the plate not less than 1.5m below normal GL. Connected to galvanized earth lead wire 4mm dia by means of nut, bolt, check nut and washers including necessary excavation and earth work in soft/loose soil, GI protection pipe light grade 15mm bore for protecting the GI wire mesh funnel alternate layer of charcoal dust, and salt PCC pit 1:3:6 type C1 using 20mm graded stone aggregate and 50mm thick RCC 1:2:4 type BO using 20mm graded stone aggregate cover reinforced with 8 mm dia MS TMT bars 80mm C/C both ways complete all as specified and shown in Electrical plate No.3 SSR part-1 and connected to the earth point and testing complete all as specified and directed.

S & F Vertical type DB with Three phase & neutral MCB Distribution Box of 4 Way, double door of protection grade IP 43 in fine powder coated, matt finish with best CRCA sheet, fitted with shrouded neutral, insulated pin type copper bus bar, Din rail, earth bar confirming to IS 13032 & 8623 including making connections with copper lugs, testing as required complete all as specified and directed.

S & F MCB with high rating MCB Triple pole, 100 Amps 240 volts AC,'C' Series, conforming to IS 8828/IEC 60898-1 including making connections with copper lugs, testing as required complete all as specified and directed.

S & F MCB with high rating MCB Triple pole & Neutral, 63 Amps 240 volts AC,'C' Series, conforming to IS 8828/IEC 60898-1 including making connections with copper lugs, testing as required complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 Sq mm 3.5 core including taking down complete all as specified & directed. Note:- Earth work, Sand & Bricks shall be paid separately under respective items

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 Sq mm 4.0 core including taking down complete all as specified & directed. Note:- Earth work, Sand & Bricks shall be paid separately under respective items

Supply and laying sub class 'B' bricks laid dry and flat across the length of cable for protection of cable complete all as specified and directed.

M & L for sand cushioning with Ganga Sand to underground cable (8 cm thick before laying and 15 cm thick after laying the cable complete all as specified & directed. Note:- Punned thickness shall be measured for payment.

S & F wall mounted type LED light fitting batten type complete with LED 1 x 18 watt, 4 feet long, extruded aluminium body with heat sink provided for efficient heat dissipation and integrate electronic drive complete with all accessories internally pre-wired and including connecting up with 3 core twisted flexible copper conductor cable complete all as specified and as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 Sq mm 4.0 core including taking down complete all as specified & directed. Note:- Earth work, sand & Bricks shall be paid separately under respective items

Taking down carefully point wiring of any type complete for light, fan socket or power point with fittings & fixtures such as ceiling rose, electric fittings, holders, switches, sockets, regulators, wooden batten, surface conduit/casing caping/concealed etc. removing materials including accessories for taking credit and making good disturbed surface to match the existing complete all as specified & directed.

S&F in replacement of sheet metal enclosure single pole and neutral enclosure with a two pin and earth plug and socket along with one MCB, single pole of current rating 20 amps, C series 240 volts AC complete all as specified & directed.

Taking down main switches fuse unit, MCB/Kit kat distribution board with steel enclosure along with MCB’s /Kit kat fuse of any amps/ways including wooden board or from steel board and making good disturbed surfaces complete all as specified & directed.

S&F sheet metal enclosure for MCB's 240 volt 8 way single pole and neutral with 200 amps rated bus bar, double door on wall with and including suitable flat iron clamps duly grouted/ fixed flush in the wall complete all as specified and directed.

M&L for concealed submain wiring using FRLS PVC insulated, unsheathed stranded copper conductor cable two single core of size 6.0 Sqmm of voltage rating upto and including 1100 volts drawn in and including PVC concealed conduit of dia not less than 20 mm dia with all fittings and accessories along with one run of PVC insulated unsheathed stranded copper conductor of size 6.0 Sqmm as earth continuity conductor including taking down old existing sub main wiring complete all as specified & directed. Note:- (i) Two runs of single core PVC cable with one run of earth conductor and conduit shall be measured as one length. (ii) The cost for cutting, chases required shall deemed to be included in the quoted unit rate.

M&L for concealed submain wiring using FRLS PVC insulated, unsheathed stranded copper conductor cable two single core of size 4.0 Sqmm of voltage rating upto and including 1100 volts drawn in and including PVC concealed conduit of dia not less than 20 mm dia with all fittings and accessories along with one run of PVC insulated unsheathed stranded copper conductor of size 4.0 Sqmm as earth continuity conductor including taking down old existing sub main wiring complete all as specified & directed. Note:- (i) Two runs of single core PVC cable with one run of earth conductor and conduit shall be measured as one length. (ii) The cost for cutting, chases required shall deemed to be included in the quoted unit rate.

M&L for cutting and chasing required upon brick wall not exceeding 20 CM girth for concealed conduit wiring and for GI earth wire including making good to disturbed surface with cement mortar 1: 3 and distemper / colour wash to match the existing surface to recess the MCB / DB/ Sheet steel enclosure complete all as specified and directed.

M&L for cutting and chasing required upon brick wall not exceeding 10 CM girth for concealed conduit wiring and for GI earth wire including making good to disturbed surface with cement mortar 1: 3 and distemper / colour wash to match the existing surface including facing / finishing complete all as specified and directed.

Siddhi Constructionn

M/S JAI DURGA CONSTRUCTION

M/S CHANDRIKA PRASAD AND SONS

M/S Garg Sons

Channa Brothers and Co.