REPAIR/MAINTENANCE OF EXTERNAL WATER SUPPLY AND ELECTRICITY DG SETS PUMP AND WATER TREATMENT PLANT AND STREET LIGHTS SECURITY LIGHTS ETC AND SUMMER AND COOLING APPLIANCES AND REWIRING AT SEVERAL BLDGS AT AIZAWL UNDER GE SILCHAR

Amount

Excavation in trenches not exceeding 1.50 metre wide and not exceeding 1.5 metre in depth and getting out in hard/dense soil complete all as specified and directed.

Returning, filling in with soil obtained from excavation including spreading levelling watering and well ramming in layers not exceeding 25 cm in soil, complete all as specified and directed.

Removing excavated material ( soil) to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

Taking down carefully copper/aluminum existing point wiring (light/fan/socket or power points) complete incl wooden battens/casing capping or conduit etc (without disturbing existing fittings point wiring etc) and all connected fittings such as switch, socket, ceiling rose, lamp holder, brackets ceiling fittings, bulk head fittings and fan regulator etc and making good to disturbed surfaces of wall floor etc complete all as specified and directed.

Dismantling of old unserviceable main switches DBs, MCB enclosures, electric meter, PVC rectangular blocks etc and keeping in safe custody either for reuse or for disposal Including making good to the disturbed surface of wall complete all as specified and directed.

M&L for Point wiring using 1100 volt grade FRLSH PVC insulated unsheathed multi strand copper conductor cable 1.5 sqmm including 1.5 Sqmm FRLSH PVC insulated unsheathed multi strand 1100 volt grade copper conductor earth wire drawn through and including concealed PVC conduit of appropriate size not less than 20 mm dia and 1.8 mm thick including all fittings viz tees, bends, junctions box , connecting earth including cutting groove for concealed wiring, making good to disturbed surface of wall/floor with cement mortar and finishes to match existing including connection of cable with MCBs or bus bar shall be done through proper size copper/brass thimble of pin/u type etc for one light/fan/bell point complete all as specified and directed.

All as per item No.06 above but for 5 Amps socket Point (Same board), complete all as specified and

All as per item No.06 above but for 5 Amps socket Point (Independent board), complete all as specified

All as per item No. 06 here in before but for one three pin 15 Amps socket outlet on independent board with 1100V grade PVC insulated and unsheathed 2.5 Sqmm multi strand FRLSH copper conductor cable and PVC insulated and unsheathed copper conductor 2.5 Sqmm , 1100 volt grade as earth continuity conductor drawn through and including concealed PVC conduit of appropriate size not less than 20 mm dia and 1.8 mm thick including all fittings viz tees, bends, junctions box , connecting earth including cutting groove for concealed wiring, making good to disturbed surface of wall/floor with cement mortar and finishes to match existing including connection of cable with MCBs or bus bar shall be done through proper size copper/brass thimble of pin/u type etc complete all as specified and directed.

S & F switch piano, 5Amp single pole, flush type one way 230 volts complete all as specified and directed.

S & F Socket outlet 2 in 1, 5 pin, 5 Amps flush type complete all as specified and directed.

S & F Switch Socket combination outlet 2-in-1, 3pin 6/5 Amps flush type complete all as specified and directed .

S & F Switch Socket combination outlet 2-in-1, 3pin 5 Amps & 3 pin 15 Amp flush type complete all as specified and directed .

S&F Bell push flush type 5 Amp, complete all as specified and directed.

S & F stepped type electronic fan regulator flush type socket type complete all as specified and directed.

S&F Modular switch 1 way 6A, 1 module fixed in repair, complete all as specified and directed.

S&F Modular switch 1 way 16A, 1 module fixed in repair complete all as specified and directed.

S&F Modular Bell push 6A 1 module fixed in repair complete all as specified and directed.

Supply and fix Socket 6A - 5/6 pin combined 2 module fixed in repair complete with cover plate all as specified.

Supply and fix Socket 6A/16Amp - 5/6 pin combined 2 module fixed in repaircomplete with cover plate all as specified.

Supply and fix Fan step regulator, 120W - 2 module fixed in repair complete with cover plate all as specified.

S&F modular blank plate 01 module fixed in repair complete all as specified and directed.

S&F modular Metal flush box alongwith 2 module White cover plate with frame fixed in repair,complete all as specified and directed.

S&F modular Metal flush box alongwith 3 module White cover plate with frame fixed in repair,complete all as specified and directed.

S&F modular Metal flush box alongwith 4 module White cover plate with frame fixed in repair,complete all as specified and directed.

S&F modular Metal flush box alongwith 6 module White cover plate with frame fixed in repair,complete all as specified and directed.

Supply and fix Ceiling rose, terminal made up of PVC/polycarbonate, isolated body complete all as specified and directed

S&F in Bell ding dong type 6 amps 240 volts complete all as specified and directed.

Taking down Ceiling fan of any size/sweep for replacing bearing, bush including rewinding after disconnecting the wire from existing ceiling rose and refixing the same after rewinding with super enamelled winding wire ,(minimum winding wire 300 grame / fan) cleaning dust, oiling greasing, servicing and replacing bearing, gun metal bush, rubber reel with clamp and nut-bolt, washer, lock pin, excellation gear sytem, boby painting etc as existing including connecting flexible 3 core cable from ceiling rose to connector of fan complete all as specified and directed.

S & F exhaust fan having PVC body of size 250 mm sweep AC single phase, 230 Volt of size with louvers connecting up including provision of fixing clamp, nut bolt and cable from ceiling rose or connector to fan, including taking down old UNSV plastic body fan complete all as specified and directed. Make: Bajaj Maxima DxI 250 mm White Dom Ex Fan or equivalent

Supply and fix sheet metal enclosure powder coated DB for fixing of MCBs, TPN 4 ways double door with 200 Amp rated bus bar, 415 Volts complete all as specified and directed.

Supply and fix sheet metal enclosure powder coated DB for fixing of MCBs, SPN 8 ways double door with 200 Amp rated bus bar, 240 Volts complete all as specified and directed.

Supply and fix sheet metal enclosure powder coated DB for fixing of MCBs, SPN 4 ways double door with 200 Amp rated bus bar, 240 Volts complete all as specified and directed.

MCB TPN 63 Amp, C Curve type, 10KA,415 volts with over load and short circuit protection complete all as specified and directed.

S&F MCB SP 6 to 32 Amp, C Curve type, 10kA, with over load and short circuit protection complete all as specified and directed.

S&F MCB SPN 6 to 32 Amp, C Curve type, 10kA, with over load and short circuit protection complete all as specified and directed.

M & L for sub main wiring with two single core 6 Sqmm PVC insulated unsheathed cable multi-strand copper conductor FRLSH drawn through and including PVC concealed conduit of suitable size with all fittings and fixing accessories on roof, walls, ceiling etc. including 1x 6 Sqmm PVC insulated unsheathed multi strand copper conductor earth wire FRLSH with proper colour coding connecting earth including cutting groove for concealed wiring, making good to disturb surface of wall/floor with cement mortar and finishes to match existing including including taking down existing unserviceable one and removing from site complete all as specified and directed. Note:- Two run of single core cable, one run earth wire and one run of PVC casingcaping/conduit will be measured as one length.

S&F lamp holder angular/batten/ Pendent insulated body with back plate for batten fittings, complete all as specified and directed.

S&F for decorative bracket wall light fittings holder type made up of PVC/Polycarbonate suitable for 7 to 10 W LED lamp one complete all as specified and directed. Make : Havells Cat Part No. LHFOFWE1TZ1W012 or equivalent to Bajaj/Philips/Wipro/Syska LED/ M/S Surya Roshni Limited/M/S Jaquar & Company Pvt Ltd/Crompton Greaves

S&F of 7-10 W LED lamp/bulb suitable for lamp holder and decorative bracket wall light fittings, complete all as specified and directed.Make:-

S&F LED light fitting 1x20Watt decorative box type with driver, holder including LED tube light/batten type connecting up with 3 core flexible copper conductor cable of suitable size from ceiling rose as applicable, complete all as specified and directed.Make : Havells Cat Part No. REGALBATTENT8UPTO1X22WDSBSWH and CRYSTALT81213SSTL20WLED865SGLASS or equivalent to Bajaj/Philips/Wipro/Syska LED/ M/S Surya Roshni Limited/M/S Jaquar & Company Pvt Ltd/Crompton Greaves

S&F mirror light LED linear fitting including Tube rod 10 watts and fixed on wall surface with PVC square box for self aligning and connected with 3 core flexible FRLS copper cable PVC insulated of size 16/0.20 mm etc complete all as specified and directed. Make : Havells Cat Part No. ENDURALINEARNEOBS10WLED 865SGL oer equivalent to Bajaj/Philips/Wipro/Syska LED/ M/S Surya Roshni Limited/M/S Jaquar & Company Pvt Ltd/Crompton Greaves

Supply and fix LED panel light size 2 x 2 designed by using latest technology, 36 watt, IP20 rating 180-220 volt cast colour for edge-lit ilumination, recess/surface mounted aesthetically designed for soft light and glare including accessories internally prewired suitable for surface ceiling/recessed mounting type including making connections with the existing supply complete all as specfied and directed. Make : Havells Cat Part No. ENDURASLIMPROPLUS2X2PLR28/36WLED840MOD or equivalent to Bajaj/Philips/Wipro/Syska LED/ M/S Surya Roshni Limited/M/S Jaquar & Company Pvt Ltd/Crompton Greaves

Taking up and down steel tubing and connections, including cleaning for refixing or removal to store 80 mm bore pipe, complete all as specified and directed.

All as per item no. 44 but of size 50 mm bore.

All as per item no. 44 but of size 40 mm bore.

All as per item no. 44 but of size 25 mm bore.

All as per item no. 44 but of size 20 mm bore.

Relaying & refixing old steel tube 80 mm bore after cleaning of all silts, dirts,mud,scales with new GI frittings and connection in new or old position with fittings in trenches/wall/floors, complete all as specified and directed.

All as per item no. 49 but of size 50 mm bore.

All as per item no. 49 but of size 40 mm bore.

All as per item no. 49 but of size 25 mm bore.

All as per item no. 49 but of size 20 mm bore.

Supply and laying steel water tubing 80 mm bore of pipe, medium grade galvanised, ISI marked with all heavy duty fittings ISI marked laid in trenches/concealed wall/ceiling or laid in foors, complete all as specified and directed.

All as per item no. 54 but of size 50 mm bore.

All as per item no. 54 but of size 40 mm bore.

All as per item no. 54 but of size 25 mm bore.

All as per item no. 54 but of size 20 mm bore.

Supply, installation and testing of Cast Iron Sluice valve, class PN 1.6, ISI marked conforming to IS-14846, complete suitable for 80 mm bore pipe with flanges ends duly drilled, brass spindle, CI gate with brass rings and iron wheel head , complete alkl as specified and directed.

Supply and fix , as in repairs 50 mm bore Gun metal , globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed including dismantling the existing one, complete all as specified and directed.

All as per item no. 60 but of size 40 mm bore Gate Valve.

All as per item no. 60 but of size 25 mm bore Gate Valve.

All as per item no. 60 but of size 20 mm bore Gate Valve.

S&F PTMT ball valves, high pressure, with polythene float Valves 25mm bore for GI pipes and all connected accessories including dismantling unserviceable valve and removing from site, complete all as specified and directed.

All as per item no. 64 but of size 20 mm dia .

M& L for supporting of pipe lines which is laying on ground level, brick work with sub class 'B' old size bricks, straight or curved on plan exceeding 6 mtrs mean radius, built in CM 1:6 , complete all as specified and directed. Note: After preparing of bricks support, pipe will be fixed or locked with GI strip for pipe protection.

Supply and fix PVC body Foot valve ISI mark of size 80 mm bore including taking out Unserviceable foot valve, complete all as specified and directed.

M&L for Cleaning and removing all silt, dirt, mud, scales etc. from 50000 ltrs capacity semi underground water storage sump by rubbing with brushes and throughly washing with bleaching powder and clean water complete including writing of date by preparing surface of size 45x30 cm and writing "TANK CLEANED ON DATE-MONTH-YEAR", complete all as specified and directed.

All as per item No. 68 but 50000 ltrs PVC Tank/SMC Tank.

All as per item No. 68 but 20000 ltrs Pressed steel Tank.

All as per item No. 68 but 20000 ltrs Sedimentation Tank.

All as per item No. 68 but 10000 ltrs RCC Tank.

All as per item No. 68 but 5000 ltrs PVC Tank/SMC Tank.

Material and labour for construction of valve pit of brick masonry of size 900 x900 x 900mm internal dimension complete with Angle Iron, 3.15mm thick MS sheet cover and locking arrangement including excavation and earth work and P.C.C 1:3:6 type with provision of two coat of synthetic enamal paint over one coat of red oxide primer including demolition of existing valve pit, complete all as specified and directed.

All as per item No. 74 but of size 750x750x750mm.

All as per item No. 74 but of size 450x450x450mm.

Material and labour for cutting of rusted MS sheet, cross arm, angle iron frame or tubular structure of pre-pressed steel OH tank at height of 3 to 11 mtrs replaced with new MS sheet, cross arm, angle iron frame or tubular stracture and welding the same at specified location to make to joint leak proof complete all as specified and directed.

Supply and fix, iron gate fabricated with angle iron/sqaure bar/iron flats with MS hinge and latch for locking incl errection at proper position and applying two coats of synthetic enamel paint , complete all as specified and directed.

M&L for steel work with steel tubular section of 40 mm dia for railing including welding & fixing at proper position and applying two coats of synthetic enamel paint, complete all as specified and directed.

M&L for preparation of surface by scrapping old painted surface and painting two coats of synthetic enamel paint on outer side of MS steel tank and sedimentation tank incl wiritng of water quantities, complete all as specified and directed.

M&L for preparation of surface by scrapping old painted surface and painting one coat of bitumen paint or paint suitable for drinking water tank on inside of MS steel tank 20,000 ltrs capacity, complete all as specified and directed.

M&L for preparation of surface by scrapping old painted surface and finishing walls with two coats of Acrylic smooth exterior paint of required shade over RCC tank surface, complete all as specified and directed.

Supply, installation, testing and commissioning, CPRI approved factory made and tested, LT feeder pillar box, outdoor type of size 1000mm x 800mm x 400mm, CPRI approved, plateform mounted , the panel shall be dust and vermin proof, IP65 class protection powder coated and made out of 3.15 mm thick CRCA MS Sheet and mounted on 50x50x5mm thick angle iron frame work, painted with two coats of synthetic enameed paint over one one coat of red oxide primer , front opening type, with aprons for cable entry, with double door shutter and locking arrangement, internal wiring with 2.5 sqmm PVC insulated, stranded copper conductor cable, IS-694 marked of adequate size and internal connection from MCCBs, MCBs and TPN aluminium bus bar and extension links of rating not less than 1.5 times the rated capacity of the respective MCCBs. The TPN bus bar and extension links shall be insulated with colour code heat shrinkable sleeve and shall be mounted epoxy regin insulator to contactor not less than 10 sqmm single core copper cable stranded copper conductor cable, IS-694 marked. The following items accommodated with this feeder pillar including 02 Nos danger notice plate made of 1.6mm thick mild steel sheet, vitreous enamelled white of size 25 x 20cm with letter figures and conventional skull bones in signal red colour and fixed nuts, bolts and washers etc with voltage and danger indicated in Hindi and English including taking down old rusted unsv feeder pillar, grouted by using PCC foundation 1:2:4 Type C1 with 20mm stone aggt, totally tested as per IEC 61439-1, complete all as specified and directed.

Incoming (a) Load change over, 32A, 4 Pole, 415V-01Nos (b) MCCB 32 Amps,4 Pole,16 KA,415V-01 Nos Outgoing (a) 0.25 HP, DOL Starter-01 Nos. (a) 0.50 HP, DOL Starter-01 Nos. (a) 3.00 HP, DOL Starter-04 Nos. (d) MCB TP 01 Amps, 10 KA,415V-02Nos (e) MCB TP 06 Amps, 10 KA, 415V-04 Nos (f) MCB DP 10-32 Amps, 10KA-07 Nos (g) Digital multi function meter -01 Nos (h) Phase indicator lamps(RYB) set of 3 - 01 set. Note:- Excavation for grouting and PCC foundation for LT Panel shall be deemed included in quoted rate

Taking out old unserviceable UG cables of any size from site, complete all as specified and directed.

Supply and spread sand in trenches as sand cushioning to under ground cable for protection with fine river sand and provide reqd cover after punning down complete all as specified and directed. Note : Thickness of sand cushion after punning down will be measured and paid.

Material and labour for laying locally available sub-class 'B' brick of size (old Size) laid flat and dry in trenches across the trench over the cable perpendiccular to the dirtection of cable for protection, complete all as specified and directed.

Supply, fixing & testing of XLPE/PVC sheathed , armoured LT electric power cable (Heavy Duty) with aluminium conductor of size 95 Sqmm, 3.5 core 1100 volts graded laid through duct/pipe/trench etc incl cable gland and lugs,complete all as specified and directed.

All as per item No. 88 here in above but of size 70 Sqmm, 3.5 core.

All as per item No. 88 here in above but of size 50 Sqmm, 3.5 core.

All as per item No. 88 here in above but of size 25 Sqmm, 3.5 core.

All as per item No. 88 here in above but of size 10 Sqmm,4 core.

All as per item No. 88 here in above but of size 10 Sqmm,2 core.

Supply and fix galvanised steel tubes of size 40 mm bore, light grade, with all fittingslaid to wall/ceiling/floor, complete all as specified and directed.

Supply and fix galvanised steel tubes of size 80 mm bore, light grade, with all fittingslaid to wall/ceiling/floor, complete all as specified and directed.

Material and labour for steel tubular swaged poles complete with cast iron base plate, finial taper plug, bolts, nuts and screws as specified type 410 SP-31 (Over all length 9 metres long) confirming to IS-2713. Pole shall be painted with two coats of black bituminious paint throughout internally and externally up to planting depth, length from bottom and the remaining external protion shall be painted with two coats of aluminium paint over a coat of red oxide primer and numbering the pole with white paint alfa numaric letters on black patch fixed in repairs complete all as specified and directed. Note: Earthwork and PCC shall be measured and paid for separatly

M&L for PCC 1:2:4 type B1 using 20 mm graded aggregate for coping the poles of any size, complete all as specified and directed.

M&L for PCC 1:2:4 type B2 using 40 mm graded aggregate as in foundation filling & mass concrete , complete all as specified and directed.

M&L for PCC 1:3:6 type C2 using 40 mm graded aggregate as in foundation filling & mass concrete , complete all as specified and directed.

Supply and fix LED Solar street light fitting 35-40 Watt including galvanized steel pole in built, lithium ion battery, solar panel, charge controller with dusk down sensor complete all as specified and directed. Make: Axxon/TATA Solcar/Bajaj/Havells/Crompton or equivalent.

M&L for straight through joints (epoxy) including joint kits and labour complete for making joints suitable for 70-95 sqmm 3.5 core UG cables of the following sizes in joint kits, complete all as specified and directed.

M&L for straight through joints (epoxy) including joint kits and labour complete for making joints suitable for 25-50 sqmm 3.5 core UG cables of the following sizes in joint kits, complete all as specified and directed.

Supply, installation, testing and commissioning, CPRI approved factory made and tested, LT feeder pillar box, outdoor type of size 1000mm x 800mm x 400mm, CPRI approved, plateform mounted , the panel shall be dust and vermin proof, IP65 class protection and madeout of 3.15 mm thick CRCA MS Sheet and mounted on 50x50x5mm thick angle iron frame work, powder coated finish over one coat of red oxide primer outside and two coats of red oxide primer on inside, front opening type, with aprons for cable entry, with double door shutter and locking arrangement, internal wiring with 2.5 sqmm PVC insulated, stranded copper conductor cable, IS-694 marked of adequate size and internal connection from MCCBs, MCBs and TPN aluminium bus bar and extension links of rating not less than 1.5 times the rated capacity of the respective MCCBs. The TPN bus bar and extension links shall be insulated with colour code heat shrinkable sleeve and shall be mounted epoxy regin insulator to contactor not less than 10 sqmm single core copper cable stranded copper conductor cable, IS-694 marked. The following items accommodated with this feeder pillar including 02 Nos danger notice plate made of 1.6mm thick mild steel sheet, vitreous enamelled white of size 25 x 20cm with letter figures and conventional skull bones in signal red colour and fixed nuts, bolts and washers etc with voltage and danger indicated in Hindi and English including taking down old rusted unsv feeder pillar, grouted by using PCC foundation 1:2:4 Type C1 with 20mm stone aggt, totally tested as per IEC 61439-1, complete all as specified and directed.

The scope of work includes the following items accommodate the same panel:- Incoming (b)MCCB 250 Amps, 4 Pole, 36 KVA, 415 V-01 Nos OUTGOING (a) MCCB 125 Amps, 4 Pole , 16KA, 415 V-01 Nos (b) MCCB 100 Amps, 4 Pole , 16KA, 415 V-01 Nos (c) MCCB 63 Amps, 4 Pole , 16KA, 415 V-02 Nos (d) MCB TPN 63 Amps,4 Pole, 16 KA, 415 V-01Nos (e) MCB SPN 32 Amps, 10 KA, 415 V-03Nos (f) Digital multi function meter -01 Nos (g) Pahse indicator lamps (RYB) set of 3 -01 Set Note:- Excavation for grouting and PCC foundation for LT panel shall be deemed incl quoted rates.

Supply, installation, testing and commissioning, CPRI approved factory made and tested, LT feeder pillar box, outdoor type of size 1000mm x 800mm x 300mm, CPRI approved, plateform mounted , the panel shall be dust and vermin proof, IP65 class protection and madeout of 3.15 mm thick CRCA MS Sheet and mounted on 50x50x5mm thick angle iron frame work, powder coated finish over one coat of red oxide primer outside and two coats of red oxide primer on inside, front opening type, with aprons for cable entry, with double door shutter and locking arrangement, internal wiring with 2.5 sqmm PVC insulated, stranded copper conductor cable, IS-694 marked of adequate size and internal connection from MCCBs, MCBs and TPN aluminium bus bar and extension links of rating not less than 1.5 times the rated capacity of the respective MCCBs. The TPN bus bar and extension links shall be insulated with colour code heat shrinkable sleeve and shall be mounted epoxy regin insulator to contactor not less than 10 sqmm single core copper cable stranded copper conductor cable, IS-694 marked. The following items accommodated with this feeder pillar including 02 Nos danger notice plate made of 1.6mm thick mild steel sheet, vitreous enamelled white of size 25 x 20cm with letter figures and conventional skull bones in signal red colour and fixed nuts, bolts and washers etc with voltage and danger indicated in Hindi and English including taking down old rusted unsv feeder pillar, grouted by using PCC foundation 1:2:4 Type C1 with 20mm stone aggt, totally tested as per IEC 61439-1, complete all as specified and directed.

The scope of work includes the following items accommodate the same panel:- Incoming (a)MCCB 100 Amps, 4 Pole, 36 KVA, 415 V-01 Nos OUTGOING (a) MCCB 63 Amps, 4 Pole , 16KA, 415 V-02Nos (c) MCCB 32 Amps, 4 Pole , 16KA, 415 V-02 Nos (d) MCB TPN 63 Amps,4 Pole, 16 KA, 415 V-01Nos (e) MCB SPN 32 Amps, 10 KA, 415 V-02Nos (f) Digital multi function meter -01 Nos (g) Pahse indicator lamps (RYB) set of 3 -01 Set Note:- Excavation for grouting and PCC foundation for LT panel shall be deemed incl quoted rates.

Supply,install testing and commissioning CPRI approved outdoor Bus Bar Box ( approx size 600 x 600 x 400 mm) CPRI approved manufacturer cubical floor mounted type factory made totally enclosed, dust and vermin proof made out of 3.15 mm thuick MS sheet duly painted with powder coated both side in and out, having proper locking arrangement in both front and rear side aluminium bus barof 200 Amps rating duly drilled holes for connection and mounted on epoxy based post insulators for 3 phase, 415 Volts, 50 Hz AC supply, cable gland and iron angleframe (bottom portiuon of the panel), grouted by PCC foundation 1:2:4 type C1 with 20mm graded stone aggt totally tested as per IEC 61439-1, complete all as specifed and directed. Note:- Excavation for grouting and PCC foundation for LT panel shall be deemed incl quoted rates.

M&L for shifting of LT panels from original position after disconnecting all electric connection distance not more than 50m including isntallation to ne w psoition and making all necessary electric conmnection including PCC founndation and excavation, complete all as sepcified and directed.

Material and labour for one coat of spray painting of transformers (any type power or distribution) of capacity upto and including 500 KVA ( in situ ) outdoor type, installed and located at different sites in scattered area under the AGE E/M Vairengte including the following: - (a) Preparation of old surfaces by cleaning, scrapping, rubbing/ polishing etc. complete. (b) Painting with two coats of Duco paint (Grey) paint of approved make / quality all as directed at site. (c) Writing the SM MES No of transformer on MS body of transformer all as directed.

Dehydration and filtration of existing transformer oil of transformer at different location with filtration machine and heating system to get the minimum di-electric strength of oil 50 KV minimum without disturbing the power supply system and refilling/ topping up /replacement of unserviceable transformer oil conforming IS-335-1993 complete all as specified and as directed. Note:- (a) Transformer oil required extra for filling/topping up shall be measured and paid separately under the relevant items of this schedule. (b) Cost of oil testing shall be deemed to be included in the unit rate quoted for this item and T&p Shall be aranged by contractor.

Supply only new transformer oil of di-electric strength not be less than 60 KV and conforming to IS-335 of 1993 for filling/ topping up oil of transformer up to desired level complete all as specified.

Supply and fix breather including silica gel, indicating type, 4 to 6 mm standard size of the particle, blue colour for transformer of capacity from 63 to 500 KVA including removing of old breather complete all as specified.

M&L in repairs for Danger Notice Plate of 1.6mm thick MS sheet, vitreous enamelled white, with letters, figures and conventional Skull and bones in signal red colour and fixed with MS clamps, bolts and nuts of approved size, for HT 1100 Volts, 250mmx 200mm size, complete all as specified and directed.

Dismantling of corroded/ rusted/defective cross arms of MS channel/angle of any section, complete all as specified and directed.

Dismantling drop out expulsion fuse single pole complete all as specified and directed.

Supply and fix drop out expulsion fuse unit suitable for 11KV of capacity up to 200 Amps mounted on MS channels complete with two post insulator 11KV including required hard ware like clamps nut bolts washers synthetic bonded fuse barrels etc all as specified.

M&L for cross arms bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts,washers,welding, bending cold or hot, drilling holes for bolts, in any shape or sizes as indicated or directed and inclusive of two coats of aluminium paint over a coat of zinc chrome primer, complete all as specified and directed.

Dismantling of old UNSV air break gang operated switches, vertical/ horizontal, mounted on insulator/operating mechanism, complete all as specified and directed.

M&L for triple pole, mechanically operated air break isolator (GOD),vertical mounting rotating type,mounted on insulator and steel frame, with operating mechanism worked from ground level complete in all respect such as gun metal moving contacts and spring loaded gun metal fixed jaws, knife copper jumper strip etc, suitable for 11KV grade with 9 insulators of rating upto 200 amps, complete all as specified and directed.

Dismantling of unserviceable insulators of any size/type complete all as specified and directed.

S&F Disc type insulator, porcelain, vitreous, 155 mm high and 255mm dia ball and socket type, white, brown or green 'Two in series' disc assembly including nuts, bolts as required for 11KV grade confirming to relevant IS, complete all as specified and directed.

S&F as in repair for lightening arrester , expulsion type with all fittings, transmission class discharge capacity 65 Kilo Amps suitable for 11KV, complete all as specified and directed.

Material and labour for earthing complete with galvanised steel earth plate electrode 600mmX600mmX6mm thick burried directly in ground (earth pit not less than 2.25 mtr below ground level) with top edge of the plate not less than 1.5 mtr below ground level connected to Galvanised Iron strip 25 x 4 mm as earthing lead and protected by 40 mm bore light grade galvanised iron pipe and other end connected to test point as directed including funnel with wire mesh and watering pipe 20 mm bore medium grade galvanised iron pipe with charcoal and common salt in alternaterlayers of 15 cm thickness all around the GI plate electrode with concrete pit in PCC 1:3:6 type C-1 with cast iron frame including cast iron cover10mm thick hinged to CI frame and 6mm MS rod for handle, necessary excavation and earth wok in hard/dense soil and disposal of spoil to a distance n exc 50 m and necessary testing complete all as shown in electrical plate No 3 of SSR 2009 Part-I all as specified and directed.

Material and labour for earthing complete with galvanised steel earth plate electrode 600mmX60ommX6mm thick burried directly in ground (earth pit not less than 2.25 mtr below ground level) with top edge of the plate not less than 1.5 mtr below ground level connected to Galvanised earth wire 4 mm dia as earthing lead and protected by 150 mm bore light grade galvanised iron pipe and other end connected to test point as directed including funnel with wire mesh and watering pipe 20 mm bore medium grade galvanised iron pipe with charcoal and common salt in alternaterlayers of 15 cm thickness all around the GI plate electrode with concrete pit in PCC 1:3:6 type C-1 with cast iron frame including cast iron cover10mm thick hinged to CI frame and 6mm MS rod for handle, necessary excavation and earth wok in hard/dense soil and disposal of spoil to a distance n exc 50 m and necessary testing complete all as shown in electrical plate No 3 of SSR 2009 Part-I all as specified and directed.

SF earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. , as required 25mmx4mm galvanised iron strip, complete all as specified and directed.

Material and labour for servicing of Air conditoner Split/window type of capacity 1.5/2.0 ton split type in position or at workshop comprising of cleaning agent and water, tightening all electricals contacts, clips, bolts, nuts etc greasing/oiling blower motor assy, testing the serviceability of rubber bushes, connector, clips, bolts,nuts, washer etc, including checking the compressor unit and repalcing unserviceable spare parts etc., complete all as specified. Note:- (a) Spare parts shall be measured and paid seperately for relevant items of schedule. (b) Gas charging and servicing will not be measured in complaint. (c) Transportation charges for original position to workshop & back and fixing charges deemed incl in quoted rate.

Supply and fix in repair/repalcement of the following spare parts as per sample and suitable for 1.5 Ton split Air conditioner:-

Starting Capacitor of suitable MFD.

Running Capacitor of suitable MFD.

Thermostart switch with regulating knob unit incl necessary fittings and allied works.

Sealed unit compressor unit incl necessary fittings and allied works.

Blower fan motor for outdoor unit incl necessary fittings and allied works.

Blower fan motor for indoor unit incl necessary fittings and allied works.

Remote control hand set

Remote control PCB circuit board incl necessary fittings and allied works.

Condensing coil Assembly incl necessary fittings and allied works such as clamps,nuts, bolts,soldering, bracing etc

Copper tubing suction and discharge line of suitable size 1/4", 5/8", 3/8" dia with heat stroke insulation incl necessary fittings and allied works.

PVC drain pipe incl necessary fittings and allied works.

PVC air filter incl necessary fittings and allied works.

Material and labour for Gas Charging with suitable refrigerant R-22/R- 134A/R-32 as filled in 1.5Ton split AC to get required back pressure and cooling to any make/model/capacity for water cooler including leak testing after and before Gas charging & make it leak proof, if any complete as specified and directed.

M&L for servicing of refrigerator capacity upto 310 litres in position or at workshop comprising of cleaning, free from dust/cleaning the evaporator, condensorcoil with cleaning agent and water, tightening all electricals contacts, nuts, bolts,etc including hecking the compressor unit and replacing unserviceable parts, electric wire etc, complete all as specified and directed. Note:- (a) Spare parts shall be measured and paid seperately for relevant items of schedule. (b) Gas charging and servicing will not be measured in complaint. (c) Transportation charges for original position to workshop & back and fixing charges deemed incl in quoted rate.

Supply and fix in repair/repalcement of the following spare parts as per sample and suitable for refrigerator of any make/model:-

Over load relay box for refrigerator of capacity upto 310 litrs including necessary fittings and allied works.

Thermostart switch defrost type with regulating knob etc. for refrigerator of capacity upto 310 litrs including necessary fittings and allied works.

Copper stainer and capacity tube for refrigerator of capacity upto 310 litrs including necessary fittings and allied works.

Condensing coil unit for refrigerator of capacity upto 310 litrs including necessary fittings and allied works.

PCB Unit including timer for refrigerator of capacity upto 310 litrs including necessary fittings and allied works.

Sealed unit compressor unit for refrigerator of capacity 165 to 210 litrs including necessary fittings and allied works.

Sealed unit compressor unit for refrigerator of capacity 280 to 310 litrs including necessary fittings and allied works.

Freezer unit with door for refrigerator of capacity 310 litrs including necessary fittings and allied works.

Door lock with duplicate keys for refrigerator of capacity 310 litrs including necessary fittings and allied works.

Freezer door for refrigerator of capacity 310 ltrs

Pigmy/cabin lamp including switch for refrigerator of capacity 310 litrs including necessary fittings and allied works.

PVC ice Tray heavy duty for refrigerator of capacity 310 litrs including necessary fittings and allied works.

PVC vegetable tray with glass cover for refrigerator of capacity 310 litrs including necessary fittings and allied works.

Chiller tray for refrigerator of capacity 310 litrs including necessary fittings and allied works.

Bottle supporterfor refrigerator of capacity 310 litrs including necessary fittings and allied works.

Magnetic door rubber beading (main door gasket) for refrigerator of capacity 310 litrs including necessary fittings and allied works.

Stainless steel door handle for refrigerator of capacity 310 litrs including necessary fittings and allied works.

PVC drain tray for refrigerator of capacity 310 litrs including necessary fittings and allied works.

Leg set of four for refrigerator of capacity 310 litrs including necessary fittings and allied works.

Material and labour for Gas Charging of Refrigerator with Refrigerant R-22/R134-A/R-32 as filled in refrigerator of capacity 310 litres to get required back pressure and cooling effect complete all as specified and directed.

M&L for painting of refrigerator of capacity upto 310 ltrs on site or at wortkshop complete all as specified and directed. Note:- (a) Preparation of old surfaces by cleaning, scrapping, rubbing/polishing etc complete. (b) Painting with two coats of synthetic enamel paint of make/colour directed by Engr-in-charge. (c) Cost of transportation and shifting of refrigerators shall be deemed inlcuding in quoted rate.

S&F as in repairs for felxible cable PVC insulated copper condcuitor for 1100 volts of size 4 sqmm 3 core,

S&F as in repairs three pin plug top 5/15 Amp, complete all as specified and directed.

Maintenance and servicing to DG set of capacity 30KVA Kirloskar Oil Rngine including attending faults on call basis for normal repairs including repalcement of defective and worn out filters, gaskets, VB-belts, Engien oil, rubber hoses, worm drive clamps, nuts bolts and cleaning of alternator with vaccum cleaner and attending faults of AMF panels etc, tappet setting if required and greasing of bearings of engines and alternator, checking of batteries, applying petroleum gel to battery terminals, adding distilled water, checking the oil, collent level at Aizwal, complete all as specified and directed. Notes:- (a) All items such as cleaning agent, cotton waste , grease, minor items such as washer, nuts, bolts etc required for carrying out the normal maintenance of the engine, mechanic charges and any specialised machine work from site workshop if required shall be demmed in quoted rates. (b) Fresh engine oil/spare parts for DG sets shall be supplied by the contractor as supply only and shall be measured and paid seperately under mentioned items in this BOQ. (c) During maintenance/ servicing of DG set, complet DG set shall be checked properly and all setting shall be doen propely and rates to be deemed in quoted rates. (d) Servicing shall be carried out after every 500 Hrs run or after 6 months whicever is earlier.

Taking out UNSV/repaireable parts from the engine 30KVA and supply/fixing of the following new spare parts including carrying out all related minor and periodical maintenance and overhauling wroks as per site requirement suitable for Kirloskar Oil Engine , complete all as specified and directed of the following:-

Air Filter

Lub Oil Filter

Pre Filter

Micro Filter

Hose (water pump to radiator)

V belt

Fuel Pipe (0665410000)

Fuel leak off pipe

Fuel Pipe( 4H03105000)

Fuel Pipe( 4H0310400)

Set of joints

Water temperature switch

Set of O rings

Set of copper washer

OFF/ON Start switch

Sensor unit for temoperature gauge

Supply & fixing new Water pump assy complete set of 30KVA DG set including all accessories such as gasket, nuts bolts and washer etc to its original position, fixed in repair, complete all as specified and as directed .

Supply & fixing new Dynamo Assy complete set of 30KVA DG set including all accessories such as nuts bolts and washer etc to its original position,fixed in repair complete all as specified and as directed.

Repair the radiator fitted in 30 KVA capacity of DG sets and strip opening complete radiator assembly,for servicing mechanically and proper cleaning of tubes with using de-scaling solution, including repair of water tubes and top/ bottom tanks by soldering / gas welding of leakage of tubes/tanks. including replacement of gasket, nut bolts,etc ensuring perfectly leak proof after servicing of radiator, re-assembling and fixing the same in position and testing the system complete all as specified and directed . Notes :- (i) The quoted rates of the contractor includes for fixing the serviceable parts in position and replacement of unserviceable parts with new parts. (ii) quoted rates are inclusive of replacement of small/minor parts such as nuts, bolts, washers, gaskets/ packing etc. (iii) The quoted rates of contractor are deemed to be included cost of transportation.

Supply and filling Lube oil grade 10W 15 for DG set 30 KVA and DG pump set, all as per requirement and directed . Make: Bharat petroleum/Indian Oil or equivalent as approved by GE.

Supply only K-cool Super (Coolant) Part No. 82022035125 all as per requirement and directed. Make: Kirloskar/Cotton Greaves or equivalent as approved by GE.

Supply and fix Diode (Positive and Negative) suitable for rotary rectifier of 30 KVA Kirloskar alternator including taking out of unserviceable parts, complete all as per requirement and directed

M&L for carrying out overhauling, caliberation of FIP, injector nozzles including connected accessories from Authorised service centre and repalcement of damage spare if any and refixing of 30KVA DG set, complete all as specified and directed.

Supply and Fixing digital/panel board type battery charger 230V AC input 12V DC out put fixed in DG panel board incl.all necessary cable connections complete all as specified and as directed by Engr- in- Charge.

Material and labour for taking out of unservicable self starter 12 volt and connected unserviceable portion of electric wiring and carring out repairs and overhauling of the self starter for 30 KVA DG set and replacement of armature, carbon brush, bearing, bendix penion,solenoid switch, bearing, tapping of field coil refixing of all component and fixed in existing postion including testing complete all as directed.

Supply and fixing in repair lead acid battery 12 Volts 90AH, PULSE Sealed maintenance free battery with three year warranty complete all as specified and as directed. Make :Exide/SF Sonic/Amron.

M & L for battery connecting wire made of copper 35 sqmm ,1.5 mtr long including brass clips/ clmps heavy duty in one side and copper lugs on other side of suitable sizes fixed, including dismantling of worn battery clamp and battery connecting wire, complete all as specified and as directed.

M & L for Servicing the silancer assembly, remove the complete silencer assembly from DG set of capacity 30 KVA by removing nuts bolts complete, including opening the wall of bldg outlet remove the old asbetose rope, remove the blockage, reassemble the silencer with DG set with new gasket, nut, bolts & washers, gas welding on damaged portion of pipe, providing asbetose rope of size 15 mm dia insulation over silencer including one coat of plaster of paris over the asbetose rope from DG set mouth to exhuast pipe end upto inside wall of DG set room appx 03 Rm length complete all as specified and as directed by Engr- in- Charge.

S&F MCCB three pole 25KA 63A, adjustable Thermal Magnetic release setting fixed to LT panel board with necessary arrangement for mounting if required , complete all as specified and directed.

S&F changeover switch with SS encloser of 63 Amps, 4 pole including necessary parts , complete all as specified and directed.

S&F of 25mmx4mm galvanised MS strip , complete all as specified and directed.

Supply only rotary barrel hand driven pump set suitable for transfering oil, diesel & kerosene, dual directional operation, solid cast iron cosnstruction, steel tubing for inlet and outlet, o1 inch outlet including 5m durable flexible pipe , complete all as specified and directed.

Servicing of Centrifugal Pump set of capacity 20HP installed at Turial, installation by Authorised Manufacturer Representative, complete all as specified and directed. Note:- (a) The cost of spare parts will be measured and paid seperately. (b) The cost of transportation (To and fro) for all kind of necessary equipments/T&P shall be arranged/brought by contractor to complete job at site or at E/M yard and the cost shall be deemed in quoted rates and no extra cost is apllicable.

Supply and fix , in replacement of Air filter for pump set of any type/make and capacity of 14.7 KW ( 20HP), complete all as specified and directed.Make: BOSCH/LUCAS/PUROLATOR or equivalent.

Supply and fix , in replacement of lubricating oil filter for pump set of any type/make and capacity of 14.7 KW ( 20HP), complete all as specified and directed.Make: BOSCH/LUCAS/PUROLATOR or equivalent.

Supply and fix , in replacement of fuel oil filter for pump set of any type/make and capacity of 14.7 KW ( 20HP), complete all as specified and directed.Make: BOSCH/LUCAS/PUROLATOR or equivalent.

Supply and fix , in replacement of fan belts 63, V-type suitable for pump set of any type/make and capacity of 14.7 KW ( 20HP), complete all as specified and directed.Make: BOSCH/LUCAS/PUROLATOR or equivalent.

Supply and fix , in replacement of fan belts 72, V-type suitable for pump set of any type/make and capacity of 14.7 KW ( 20HP), complete all as specified and directed.Make: BOSCH/LUCAS/PUROLATOR or equivalent.

Supply and fix , in replacement of battery terminals made of brass, suitable for battery of any type/make and capacity , complete all as specified and directed.Make: BOSCH/LUCAS/PUROLATOR or equivalent.

Supply and fix , in replacement of piston suitable for pump set of any type/make and capacity of 14.7 KW ( 20HP), complete all as specified and directed.Make: Kirloskar/Champion/Ghelani

Supply and fix , in replacement of piston ring suitable for pump set of any type/make and capacity of 14.7 KW ( 20HP), complete all as specified and directed.Make: Kirloskar/Champion/Ghelani

Supply and fix , in replacement of connecting bearing suitable for pump set of any type/make and capacity of 14.7 KW ( 20HP), complete all as specified and directed.Make: Kirloskar/Champion/Ghelani

Supply and fix , in replacement of crank bush brass suitable for pump set of any type/make and capacity of 14.7 KW ( 20HP), complete all as specified and directed.Make: Kirloskar/Champion/Ghelani

Supply and fix , in replacement of main bearing suitable for pump set of any type/make and capacity of 14.7 KW ( 20HP), complete all as specified and directed.Make: Kirloskar/Champion/Ghelani

Supply and fix , in replacement of center bearing suitable for pump set of any type/make and capacity of 14.7 KW ( 20HP), complete all as specified and directed.Make: Kirloskar/Champion/Ghelani

Supply and fix , in replacement of nozzle suitable for pump set of any type/make and capacity of 14.7 KW ( 20HP), complete all as specified and directed.Make: Kirloskar/Champion/Ghelani

Supply and fix , in replacement of planjar spring suitable for pump set of any type/make and capacity of 14.7 KW ( 20HP), complete all as specified and directed.Make: Kirloskar/Champion/Ghelani

Supply and fix , in replacement of head gasket suitable for pump set of any type/make and capacity of 14.7 KW ( 20HP), complete all as specified and directed.Make: Kirloskar/Champion/Ghelani

Supply and fix , in replacement of oil seal complete suitable for pump set of any type/make and capacity of 14.7 KW ( 20HP), complete all as specified and directed.Make: Kirloskar/Champion/Ghelani

Supply and fix , in replacement of gasket unit complete suitable for pump set of any type/make and capacity of 14.7 KW ( 20HP), complete all as specified and directed.Make: Kirloskar/Champion/Ghelani

M & L for taking out of unserviceable Dynamo Assy complete set from 14.7 KW, 20HP pump set including Supply & fixing new Dynamo Assy complete set including all accessories such as nuts bolts and washer etc to its original position complete all as specified and as directed by Engr- in- Charge.

Supply and fix , in replacement of radiator hose flexible, with and including taking out old hose and making all connection, testing for smooth operation, complete all as specified and directed.Make: Kirloskar/Cummins

Supply and fix , in replacement of coupling suitable for Centrifugal pump of Diesel Enginecapacity 14.7 KW 20 HP, complete all as specified and directed.

Supply and fix , in replacement of battery 12 V suitable for DG set, complete all as specified and directed.

Supply and fix , in replacement of leather gasket ISI marked, complete all as specified and directed.

Supply and fix , in replacement of gland gasket of different sizes, complete all as specified and directed.

Supply, laying connecting testing only XLPE/PVC sheathed, armoured LT electric power UG Cable (Heavy duty) with stranded aluminium conductor of size 16 Sqmm, 4 core 1100 volts grade, laid through duct/pipe/in trenches. incl cable gland and lugs complete all as specified and directed.

Taking out old unserviceable street/ security/ flood/ garden lights from site of work all as directed.

Taking out old unserviceable UG cables of any site of work all as directed.

Supplying, laying, jointing, testing and commissioning 1100 volts grade, XLPE insulated, screened, PVC sheathed, galvanised steel pipe or wire armoured, heavy duty electric cables with aluminium conductor, cross sectional area of size 06 sq mm 02 core and laid in trenches/ducts /floor passing through pipe etc complete all as specified.

Material & labour GI tube light grade 25 mm bore with all fitting laid to wall and ceilings, complete all as specified and directed.

Supply and fix PVC junction box with hinged door and locking arrangements, weather proof with IP 65 protection and facilited for cable entry in and out of size 150mm x 100mm to be fixed on circular steel pole including fixing arrangements with 4 mm MS clamps and nut bolt of suitable size and comprising of PVC connector and MCB SP 10 KA, 6 Amps including taking down old one all as specified.

Supply and fix street light fitting LED of 60 watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP65/66 protection, complete all as specified and directed. Make : Crompton Greaves Cat Part No. LST-60-CDL-M or equivalent to Bajaj/Philips/Wipro/Syska LED/ M/S Surya Roshni Limited/M/S Jaquar & Company Pvt Ltd/Havells

Supply and fix street light fitting LED of 45 watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP65/66 protection, complete all as specified and directed. Make : Crompton Greaves Cat Part No. LST-45-CDL-1 or equivalent to Bajaj/Philips/Wipro/Syska LED/ M/S Surya Roshni Limited/M/S Jaquar & Company Pvt Ltd/Havells

Supply and fix bldg security light fitting 20-25 watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP65/66 protection, complete all as specified and directed. Make : Crompton Greaves Cat Part No. LSTS-20-CDL-M or equivalent to Bajaj/Philips/Wipro/Syska LED/ M/S Surya Roshni Limited/M/S Jaquar & Company Pvt Ltd/Havells

Supply and fix flood light fitting 50 watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP65/66 protection, complete all as specified and directed. Make : Crompton Greaves Cat Part No. LFT-50-CDL/60-M or equivalent to Bajaj/Philips/Wipro/Syska LED/ M/S Surya Roshni Limited/M/S Jaquar & Company Pvt Ltd/Havells

Supply and fix LED Solar street light fitting 35-40 Watt including galvanized steel pole in built, lithium ion battery, solar panel, charge controller with dusk down sensor complete all as specified and directed. Make: Axxon/TATA Solcar/Bajaj/Havells/Crompton or equivalent.

M&L for fabrication of GI pipe bracket made out of 40 mm bore medium grade pipe bend to shape required suitable for mounting street light on pole or on wall including bracket mounting clamp, nuts and bolts, painitng with synthetic enamel paint, complete all as specified and directed.

S & F Crown shape post top lantern in soothing opal finish made up of polycarbonate material suitable upto 15-20 watt LED lamp with robust design and efficient light distribution, complete all as specified and directed. Make : Havells Cat Part No. LHDC10115099 or equivalent to Bajaj/Philips/Wipro/Syska LED/ M/S Surya Roshni Limited/M/S Jaquar & Company Pvt Ltd/Crompton Greaves

S&F post top lantern/gate light LED type 25 watt 230 V AC outdoor type with decorative post top for 360 degree indirect light IP65 protection with impact and corrosion resistant complete with driver and lamp , complete all as specified and directed. Make:-Cat No. ORALPT25WLED757PSYMTOPC of Havells or equivalent to Bajaj/Philips/ Wipro/ Syska LED/ M/S Surya Roshni Limited/M/S Jaquar & Company Pvt Ltd/Crompton Greaves

S&F for steel work with tubular section including special shape washer etc. for globe/gate light fittings heavy grade of size 60 mm dia duly painted with black/white colour synthetic enamel paint over a coat of red oxide primer and cut into pieces of required length, including taking down old one and fixing, complete all as specified and directed.

S&F PVC sheathed, insulated, copper conductor cable of size 1.5sqmm 3 core for electric connection to street light, flood light, globe light, gate light etc., complete all as specified and directed.

MS AFTAB LASKAR

M/S LUIT CONSTRUCTION

M/S P K ROY AND SONS

M/S TAPAN KUMAR RAY