ADDITION/ALTERATION AND SPECIAL REPAIR TO MD ACCN AT SHILLONG UNDER GE SHILLONG

Amount

NOTE (Applicable for all items):- The bidders/contractors are advised to read tender documents & all corrigendum/amendments and General conditions of contracts before entering/quoting the rates. SCHEDULE 'A' PART-I FOR B/R PORTION

Taking down chowkat or frame exc 1.5 Sqm but n.exc 4 Sqm each (without taking off shutter from the frame) complete all as specified and directed.

Taking down chowkat or frame n. exc 1.50 Sqm each with shutter (without taking off shutter from the frames) complete all as specified and directed.

Taking down shutter of any description nexc 1.0 Sqm and refixing in same opening complete all as specified and directed.

Taking down shutter of any description exc 1.0 Sqm and nexc 2 sqm and refixing in same opening complete all as specified and directed.

Taking down shutter of any description exc.1.0 Sqm and n.exc 2.0 sqm each complete all as specified and directed.

Taking down shutter of any description n exc.1.0 Sqm each complete all as specified and directed

Demolition of Brickwork/solid concrete block work built in Cement mortar complete

Demolition of cement concrete in ground floors and pavings n exc 15cm thickness (below or above ground lever) complete all as specified and as directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Dismantling floor, hearth , wall tiling including cement mortor bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors aprons laid in any mortar complete all as specified and directed.

Dismantling of plain/corrugated steel sheeting any gauge, thickness in roof covering complete all as specified and directed.

Demolition and breaking up drain pipes 150mmdia (SGSW, AC or reinforced concrete pipe set in cement mortar) complete all as specified and directed.

Dismantling wall and ceilling board of any description including cover fillets complete all as specified and directed.

Dismantling boarding any description fixed in any position with nails complete all as specified and directed

Dismantling of timber scantling 40 sqcm and over in section in any position (unframed work) complete all as specified and directed.

Material and labour for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Material and labour for pre painted galvatume aluminium zinc coating GI based plain steel sheet as in ridge of 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Material and labour for 4mm thick (600mmx600mm) non asbestos fibre cement building boards fixed or laid/inserted to timber/GI/Aluminium frame work with screws as in ceiling complete, complete all as specified and directed.

Supply and fix aluminium snap grid frame work for false ceiling incl 6 mm dia GI hanger (upto 1200mm length) adjusting level fixed to roof slab/truss/purlins/rafters @ 1.2 m C/C complete all as specified and as directed

Material and labour second class hard wood boarding 20mm thick fixed with nails in eaves board planed one side with butt joint complete all as specified and directed.

Material and labour second class hard wood in scantling clean sawn timber fixed all as specified and as directed.

Material and labour second class hard wood plain solid straight chowkats and frames wrought framed rebated on the solid ,rounded or chamfered ,put together with glue pinned at joints , supplied and fixed.

Supply and fix 30 mm thick Flush door shutters solid core construction with block board core and ply wood face pannels commercial on both faces complete all as specified and directed.

Supply and fix stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

Supply and fix 18/19 mm thick block boards fixed with screws to timber frame complete all as specified and as directed

Supply and fix 12 mm thick PVC boards fixed with screws to timber frame complete all as specified and as directed

Supply and fix 0.90 mm thick PVC decorative laminates type 1 of surface finish color and pattern as approved fixed with approved adhesive as per manufactures instruction complete all as specified

Supply and fix brass 150 mm long barrel tower bolt with cast or sheet barrel and rolled or cast bolts and fixed complete

Supply and fix brass 100 mm long barrel tower bolt with cast or sheet barrel and rolled or cast bolts and fixed complete

Supply and fix extruded fancy type Brass handle fabricated type of size 150 mm complete all as specified and directed.

Supply and fix extruded fancy type Brass handle fabricated type of size 100 mm complete all as specified and directed.

Supply and fix butt hinges 100 mm extruded brass with mild steel hinge pin bright polsihed and fixed type B-11 complete all as specified and directed.

Supply and fix Aluminium anodised barrel tower bolt of extruded section and fixed complete 150 mm long complete all as specified and directed.

Supply and fix extruded aluminium alloy handle fabricated type anodised of size 150 mm complete all as specified and directed.

Supply and fix butt hinges 100 mm medium weight mild steel cold rolled and fixed complete all as specified and directed.

Supply and fix Magnet catches for cupboard shutter, brass body and striking plate including letting in all as specified and as directed

Material and labour for framed work as in doors or gates of angle or other section for fixing of sheets and similar works complete of Gde Fe-290(Gde E-165) all as specified and as directed

Material and labour for powder coated (min powder coating 50 micron) anodised aluminium frame for doors, windows , ventilators plain or sliding type with one or more rebates including joining cleat for fixing etc complete all as specified and as directed

Supply and fix powder coated(powder coating min 50 micron) anodised sliding door shutters , aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, rubber neoprene packing , handles 2 nos in each door , hinges , anodised aluminium snap beading screws etc complete all as specified and directed.

Supply and fix powder coated(powder coating min 50 micron) anodised window and ventilator shutters side hung/sliding type without sash , aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, rubber neoprene packing , anodised aluminium snap beading screws, anodised aluminium fittings such as peg stays 150 mm long(1 no) hinges type B-21 100 mm long (2 No) suitable handle (1 No ) complete all as specified and directed.

Material and labour for 4.80 mm thick sheet glass quality and glazing fixed to aluminium frame exc 0.50 sqm complete all as specified and as directed.

Material and labour for 4.80 mm thick frosted sheet glass quality and glazing fixed to aluminium frame exc 0.50 sqm complete all as specified and as directed.

Material and labour for prelaminated particle board of 9 mm thk board, interior grade, prelaminated one side with decorative choice lamination & other side balancing, white lamination, fixed with screws to timber frame work.

Material and labour for precast cement concrete block massonry with solid blocks exc 10 cm in width and settings in CM 1:6 type C1 1:3:6 (20mm graded stone aggregate) ccomplete all as specified and directed.

Material and labour for precast cement concrete block massonry with solid blocks nexc 10 cm in width and settings in CM 1:4 type C1 1:3:6 (20mm graded stone aggregate) complete all as specified and directed.

Material and labour for 75mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in subfloors finished even and rough without using extra cement complete all as specified and as directed.

Material and labour for vitrified tiles lightshade (square /rectangular) polished area of each tiles nexc 0.36 sqm in floors laid over and incl. 20mm thick 1:6 screed bed jointed pointed with coloured cement to match the tiles complete all as specified and directed.

All as Per Item No 1.048 above but in vertical surfaces such as skirting / dado laid over and incl. a backing coat of 10mm thick CM 1:4 complete all as specified and directed.

Material and labour Glazed ceramic Coloured Tile 300x450x7mm/300x600x7 mm thick in Skirting, Dados, etc., Set and Jointed in Neat Cement Slurry and Pointed in White or Colour Cement to match laid over a backing coat of 10mm thick CM 1:4 screed, complete all as specified and as directed.

Material and labour for 18/20mm thk granite slab ( as in table top rubbed and polished) as in counter basin fixed in CM 1:4, pointing in white cement 1:2 using granite dust with admixture of pigment to match complete including dismantling the existing slab complete all as specified and directed.

Labour only for chamfer , splays or arris in facework of Granite not exc 15mm wide complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

Taking down plastering on lathing (other than wire-netting, without removing lathing, in cement mortar (one side only measured in cases where both sides are plastered).

Material and labour for rendering 15mm thick on fair faces of brick or concrete work in CM 1:4 finished even and fair without using extra cement complete all as specified and directed.

Supply only Integral waterproofing compound (ISI marked)

Material and labour for rendering 15mm thick on fair faces of brick work in CM 1:6 finished even and fair without using extra cement complete all as specified and directed.

Material and labour for rendering 5mm thick on fair faces of brick work in CM 1:3 finished even and fair without using extra cement as in ceiling complete all as specified and directed.

Material and labour for applying two coats of oil bound distemper using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and directed. Note : - Sanding of surface to be done by mechanical sander with 1500 - 2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer. Proper masking to be carried out before primer and paint application).

(A) Complete removal of existing treatment on wall/ roof projections including facia, cornices etc by scrapping with mechanical sander (having mechanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean,free from dust, loose paint etc by skilled labour complete all as specified and directed. (B) M&L for waterproof cement based putty @ 1 Kg(undiluted) per sqmtr. of average thickness 1 mm over the plastered/old painted wall after scrapping to prepare the surface even and smooth complete and sanding of the putty surface with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 240 Grit or above to make the surface free from dust etc. by skilled labour as per following steps:- Step 1) Mix the putty powder by adding water as per manufacturer instructions and mix it with putty mixer with the mixing capacity of min 2.5 kg putty per minute. Step 2) Apply the first coat the prepared mixer with the help of fully automatic airless spray machine of putty application having flow speed of max 6 ltrs per minutes with a maximum pressure 3300 PSI Step 3) Allow 6-8 hrs time to dry the putty surface. (C) M&L for applying two coats of oil bound distemper using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and directed.

A) Complete removal of existing treatment on wall/ roof projections including facia, cornices etc by scrapping with mechanical sander (having mechanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean,free from dust, loose paint etc by skilled labour complete all as specified and directed. (B) M&L for waterproof cement based putty @ 1 Kg(undiluted) per sqmtr. of average thickness 1 mm over the plastered/old painted wall after scrapping to prepare the surface even and smooth complete and sanding of the putty surface with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 240 Grit or above to make the surface free from dust etc. by skilled labour as per following steps:- Step 1) Mix the putty powder by adding water as per manufacturer instructions and mix it with putty mixer with the mixing capacity of min 2.5 kg putty per minute. Step 2) Apply the first coat the prepared mixer with the help of fully automatic airless spray machine of putty application having flow speed of max 6 ltrs per minutes with a maximum pressure 3300 PSI Step 3) Allow 6-8 hrs time to dry the putty surface. (C) Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm

NOTES FOR ITEM NO. 1.060, 1.061 & 1.062:- (a) The work pertaining to periodical services & Water Proofing shall be executed by authorized applicator through manufacturer of which the materials .i.e. Paint, Distemper, Putty etc. is proposed to be used by the contractor and approved by GE. (b) Cost of scaffolding upto 10m height of building shall be included in the quoted rate. (c) The contractor shall upload MOU letter with any one of manufacturer and also with their authorised applicator mentioned in the tender alongwith their bid in cover-I failing which his bid will be rejected. Authorised applicator shall have valid authorisation letter from the manufacturer (Minimum regional HQs) and shall have been issued not less than 30 days from the date of commencement of the work. The authorisation letter needs to be valid for the complete period of execution of the painting work. (d) After preparation of the surface, Engr-in-Charge shall approve the same before applying primer and finishing coats. (e) Building wise stage passing register shall be maintained and shall be signed by Engr-in-Charge and contractor. (f) The equipments to be used in the work shall be certified by the manufacturer with whom the MOU been entered into. (g) Contractor shall submit approved company generated 05 years warranty card at the time of submission of RAR & Final Bill.

Supply and fix in repair 20 mm dia harrison rails, chromiun plated with wooden finished fancy type with fixing brackets stops, rollers etc complete all as specified and directed.

Supply and fix in repair 20 mm dia double rod brackets stops , rollers etc wooden finished complete all as specified and directed.

Supply and fix solid PVC door frame of size 50 mmx 47 mm made out of 5mm plain colour PVC sheet reinforced with MS square tube as per specifiecation complete

Supply and fix factory made solid PVC moulded door shutter with particle board core 28 to 30 mm thick (stiles) with 2,4 or 6 raised panel design with 2 mm thick moulded PVC sheet on front face & 2 mm plain colour PVC sheet on back face as per specification complete

Supply & Fix for Factory made solid panel PVC door shutter 30 mm thick (style) considering of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rails, lock rail & bottom rails on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, fixing in the frame at site as per specification & drawing.

Material and labour for non skid ceremic coloured joint free tiles 7 to 8mm thick area of each tile exc 0.06 sqm but n exc 0.11 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to mortar.Laid over and including15 mm thick cement screed bed in CM 1:6 complete all as specified and directed.

Material and labour for Non Skid Ceramic (coloured) joint free tiles 7 to 8 mm thick area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tile colour including Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM (1:6). complete all as specified and directed.

Supply and fixing in repair Bib tap, cast copper alloy fancy type , screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

Supply and fix in repair Vitreous China EWC including seat cover closed pattern single piece size 755x365x655 complete all as specified and directed

Supply and fix in repair Towel rack 600mm long with lower hangers , stainless steel of make Jaguar Cat Part No:-AKP-35781PS or equivalent in Marc/Parryware

Supply and fix in repair vitreous China clay table top WHB of make Jaguar Cat Part No :OPS-WHT-15901N size of 480x480x135 mm incl waste coupling Cat Part No:-ALD-727 complete or equivalent in Hindware/Marc/Parryware

Supply and fix in repair Brass CP 2-in-1 Angle cock with flange of make Jaguar Cat Part No:-ORP-10041PM OR equivalent in Marc/Parryware

Supply and fix in repair fancy type tall body with 155 mm extension body fixed spout without popup waste system with 600 mm long braided hoses of make Jaquar Cat Part No:- KUP-35005BPM or equivalent in Marc/Parryware

Supply and fix in repair 15 mm bore CP health faucet cock with Flexible pipe 1 m long of make Jaguar Cat Part No:ALD-565 or equivalent in Marc/Parryware

Supply and fix in repair Soap dish holder of make Jaguar Cat Part No:-AKP-35731P or equivalent in Marc/Parryware

Supply and fix in repair Toilet roll holder with stainless steel flap of Make Jaguar Cat Part No:- AKP-35753PS OR EQUIVALENT IN Marc/Parryware

Supply and fix in repair Towel ring sqare shape stainless steel of Make Jaguar Cat Part No:-AKP-35721P or equivalent in Marc/Parryware

Supply and fix in repair corner glass shelf with bracket of make Jaguar Cat Part No:CAN-1173 or equivalent in Marc/Parryware

Supply and fix in repair CP over head shower square shape of size 150x150mm of make Jaquar cat part No:OHS-CHR-1619 with CP shower arm of size 400x25x25 mm square shape for wall mounted showers flange of make Jaquar Cat partNo-SHA-455L400 or equivalent in Marc/Hindaware/parryware

Supply and fix in repair CP single lever wall mixer 3-in-1 system with provision for bath hand shower & overhaed shower complete with 115 mm long bend pipe connecting legs & wall flange (without hand & ober head shower) of make Jaquar cat part No:OPP-15125PM or equivalent in Parryware/Marc/Hindware

Supply and fix CP Hand shower 24x24 mm sqaure shape single flow with Air effect (ABS body & face plate chrome plated) with Rubit cleaning system of make Jaquar cat part No:HSH-35537 with flexible tube in chrome finish 1.5 m long with nuts of make Jaquar cat part No:SHA-571 or equivalent in Parryware/Marc

Supply and fix in repair Brass CP angular stop cock fancy type with Capstan heads of make Jaguar/Marc/Parryware

Supply and fix in repair Brass chromium plated bottle traps 32 mm dia for wash basins with inlet and outlet screwed for pipe or connections incl necessary packing uniun and cap and fixed in repair.

Material and labour 75mm dia PVC(SWR)floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

Material and labour for 110 mm PVC (SWR) pipes single socketed in any length with rubber ring joints ,laid in trenches or in floors complete all as specified and directed.

Material and labour for 75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints ,laid in trenches or in floors complete all as specified and directed.

Supply and fix PVC (SWR) bend 110mm dia complete all as specified and as directed

Supply and fix PVC (SWR) bend 75mm dia complete all as specified and as directed

Supply and fix PVC(SWR) 75mm dia vent cowl complete all as specified and directed.

Supply and fix Stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays ,incl bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

Supply and fix PVC Connections 15mm size with PTMT Nuts of length 450mm and fixed, complete all as specified and as directed.

Dismantling water tanks exc 500 ltrs but not exc 1000 ltrs capacity , complete all as specified

Supply and fixing in repair rotational moulded HDPE water storage tank ,double layer ,ISI marked (cylindrical vertical type with closed top) of capacity 500 ltrs in position incl float valve high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed all as specified and directed.

Supply and fixing in repair rotational moulded HDPE water storage tank ,double layer ,ISI marked (cylindrical vertical type with closed top) of capacity 1000 ltrs in position incl float valve high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed all as specified and directed.

Material and labour for preparation of old wooden surfaces of any description over 10cm in width or girth and treated with one coat of synthetic enamel paint complete all as specified and directed.

Material and labour 12 mm thick toughened sheet clear glass incl edges bevelled /rounded incl grinding / cutting complete with all fittings/ washers/handlesand bolts complete all as specified and directed.

Material and labour for 18/19 mm thick WPC (wood Plastic composite) board of grade 1 quality exterior grade complete all as specified and as directed

Material and labour for 12 mm thick for block board grade 1 quality exterior grade decorative face with veneers on one faces complete all as specified and as directed

Material and labour for decoratives PVC laminates type I or surface finish colour and pattern as approved of thickness 1.20 mm complete all as specified and as directed

Supply and Fix for stainless steel basket of size 480X510X200 mm for cutlery and other accessories complete all as specified and as directed.

Supply and Fix for stainless steel basket of size 430X500X200 mm for cutlery and other accessories complete all as specified and as directed.

Supply and Fix for stainless steel basket of size 480x510x100mm for cup and saucer and other accessories complete all as specified and as directed.

Supply and Fix for stainless steel basket of size 430X500X100 mm for cutlery and other accessories complete all as specified and as directed.

Supply and Fix for stainless steel organisor pull out of size 150x510x560 mm and other accessories complete all as specified and as directed.

Supply and Fix for stainless steel plain basket of size 430X510X150 mm and other accessories complete all as specified and as directed.

Supply and Fix for stainless steel dustbin holder of dia 300 mm complete all as specified and as directed

Supply and Fix for stainless steel side hanger of length 350 mm complete all as specified and as directed

Supply and Fix for auto close concealed hinge of stainless steel of size 100 mm complete all as specified and as directed

Supply and Fix Brass handle of size 250mm with screws complete all as specifeid and as directed.

Supply and Fix Brass handle of size 150mm with screws complete all as specifeid and as directed

Material and Labour for drawer channel (soft close) of length 500 mm complete all as specified and as directed

Material and Labour for edge beading of WPC board fixed with nails and adhesives complete all as specified and as directed

Material and Labour for 5.80 mm thick sheet glass of ordinary quality and glazing with oil putty in square exc 0.50 sqm complete all as specified and as directed

Material and Labour for 8.00 mm thick sheet glass of ordinary quality and glazing with oil putty in square exc 0.50 sqm complete all as specified and as directed

Supply and fix in repair lever sink mixer with swinging spout on upper side (wall mounted model ) with connecting legs & wall flanges of make Jaquar cat part No:LYR-38165 or equivalent in Parryware/Cera/Marc

Supply and fix in repiar stainless steel sink 1.00 mm thick for kitchen or laboratory with plug waste pipe washer , including cantilever cast iron brackets connecting union etc overall size 495mmx420mm with two bowl size 410mmx 330mm x 160 mm complete all as specified and directed.

Supply and fix in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever barackets and connecting union to pipe overall size 495mmx420mm bowl size 410mmx330mmx160mm complete all as specified and directed.

Supply and fix Stainless steel kitchen plate rack of size 31" X 30' X 10" made out of stainless steel sheet of 1.00 mm with all accessories including taking down old unservicable rack.

Taking up or down steel tubing including fittings and disconnection, for 15mm bore of pipes.

Taking up or down steel tubing including fittings and disconnection, for 20mm bore of pipes.

Supply and Laying Steel Water Tubing 15mm bore, Galvanised, ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situation, complete as all specified and as directed.

All as per Item No. 1.124 above, but for 20mm bore.

Supply and fix stop valve cast copper alloy screwed down, high pressure with crutch or butter fly handle 20mm dia complete all as specified and directed

Supply and fix stop valve cast copper alloy screwed down, high pressure with crutch or butter fly handle 15mm dia complete all as specified and directed

Material and Labour for cutting chases, pinning in concrete block workmaking good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades shelves, lintels etc, and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10cm girth complete all as specified and directed.

Material and labour for non skid ceremic coloured joint free tiles 7 to 8mm thick area of each tile exc 0.18 sqm but n exc 0.36 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to mortar laid over and including15 mm thick cement screed bed in CM 1:6 complete all as specified and directed.

Supply and fixing in repair Vitreous china squatting pan of pattern 'long pan' size 580mmx440mm white with 'P' or 'S' trap front or back inlet and foot rests, any pattern (excluding flushing cistern and flush pipe) complete all as specified and directed.

Supply and fixing in repair PVC valveless, 10 ltrs, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified.

Supply and fix in repair Vitreous china WHB, white, flat back, of size 550 x 400 mm including brackets and pedestal, waste coupling 32mm, and waste Pipe, 32mm complete all as specified and directed.

Supply and fix in repair basin mixer 15 mm, chromium plated, fancy type complete all as specified and directed .

Supply and fixing in repair 3mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and directed.

Material and Labour for 2 mm thick fibre reinforced translucent corrugated sheeting with one and half corrugation side lap fixed with coach screw and washer in roof, wall etc complete all as specified and as directed

Material and labour for roof truss ( framed), trussed , purlin etc. of angle or other section for fixing of sheets and similar works complete of Gde Fe-290(Gde E-165) all as specified and as directed

Material and labour 100mm thick cement concrete using (40mm graded stone aggregate) type D-2 (1:4:8) as in sub base complete all as specified and directed.

Material and labour 100mm thick PCC 1:2:4 type B2 using 40mm graded stone aggregate as in subfloors finished even and rough without using extra cement complete all as specified and as directed.

Material and labour for vitrified tiles dark shade (square /rectangular) polished area of each tiles not exc0.36 in floors laid over and incl. 20mm thk 1:6 screed bed jointed pointed with coloured cement to match the tiles complete all as specified and directed.

All as per Item No 1.139 above but in vertical surfaces such as skirting / dado laid over and incl. a backing coat of 10mm thick CM 1:4 complete all as specified and directed.

Dismantling post or strut (Wood, steel, RCC) any section incl taking out embeded portion by demolition of cement concrete in fdn and making good the disturbed portion of ground, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for.

Dismantling fencing wire mesh any type, complete all as specified and directed.

Excavation in post holes not exc. 0.5 cum, getting out returing, filling in and ramming earth and broken hard core/rubble mixed with earth with around the layers not exceeding 25 cm each layers watering and removing surplus soil to a distance not exceeding 50m making good complete in soft/loose soil complete all as specified and directed.

Material and labour for Precast RCC (1:1.5:3) type A-2 using 40mm graded stone aggregate as in boundary pillars and posts etc. set in CM (1:4) complete all as specified and directed.

M & L PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

Material and Labour for Mild steel work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

Material and Labour for work for screws bolts (Machine made) with hexagonal or square heads at one end and screwed both ends, each screwed end to be fitted with wasahers and square nut, exc. 5 cm and n. exc. 10 cm long diameter of shank 11 to 15 mm complete all as specified and directed.

Material and labour for preparation of steel surfaces of any description , over 10 cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Supply only chain link MS galvanisd fencing, any size or type complete.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed by Engr-In-Charge

Material and Labour for round bars/TMT steel bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia) all as specified and directed.

Material and Labour as in repair 1mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required

Material and labour for walling of random rubble stone masonry uncoursed well bonded bedded and solidly hearted built in CM 1:6 brought upto course complete all as specified and directed.

All as per item No 1.154 above but except stone.

Material and Labour for pre cast cement concrete 1:3:6 Type C1 using 20 mm graded stone aggregate and setting in CM 1:6 concrete in joints to match as in bond stone complete all as specified and directed.

Extra over stone walling for hammer dressing to face stone and dressing face beds and joints as specified of random rubble walling uncoursed or brought upto courses surface n exc 40 mm line and sand stone

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified of random rubble walling with maximum depression on face from straight edge held against the dressed surface not exceeding 20mm line and send stone, complete all as specified and directed by Engineer-in-Charge.

Material and labour raised pointing to random rubble masonry uncoursed or brought upto courses in CM 1:4 complete all as specified and directed.

Material and labour for PCC 1:2:4 type B1 (Using 20 mm graded stone aggr) as in coping and similar works incl necessary from work acomplete all as specified and directed.

Material and labour Rendering 10mm thick on concrete surface of wall in CM (1:6) and finished the surface fair & even without using extra cement, complete all as specified and as directed.

Material and labour for 20mm thick cement plaster on stone masonry surfaces to random rubble masonry uncoursed or brought upto courses in CM 1:4 complete all as specified and directed.

Material and labour for cement concrete 1:3:6 type C2 using 40mm graded stone aggregate 75mm thick as in plinth protection finished even and fair with out using extra cement complete all as specified and directed.

Material and Labour for PCC 1:3:6 C2 (40 mm graded stone aggregate) as in surface channels and drains all as specified & directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms,moulds,mitred/ stop ends complete all as specified and directed.

Material and labour for preparation of new or previously untreated surfaces of wood and wood based materials of any description not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint over a coat of pink primer all as specified and as directed.

Material and labour preparation of old decorated surface and applying of two coat white wash on old surface of ceiling complete all as specified and directed.

Material and labour preparation surface of wood and wood based material new or old of any description and girth and treated with creosote oil complete.

S&F aluminium guide rail three track having two PVC wheel 50 mm dia for smooth functioning of cupboard/door shutter complete as specified and directed.

S&F compacted recessed handle of size 125 mm as specified and directed

S&F in repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F glass film for sliding door of cupboards as directed.

S&F Vitreous china wash down water closet pan padestal pattern white, excluding fixing bolts, flushing cistern but including flush pipe, seat and cover complete all as specified and as directed.

S&F 35mm thick 2nd class hard wood Skelton shutters open rebated and prepare to receive glass, gauze, etc complete all as specified and directed

S&F extruded aluminium alloy handles fabricated type anodised of size 100 mm complete all as specified and directed.

S&F butt hinges 75 mm medium weight mild steel cold rolled and fixed complete all as specified and directed.

S&F framed works such as grills, gratings, etc with ends of bars shouldered and /or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk way, railing, frame work of water tanks and similar work conforming to Fe 290 Gde- E-165 complete all as specified and directed.

M&L for 2nd class hard wood Plain fillets square , rectangular or triangular in section , clean swan secured with nails sectional area exc 13 sqcmnexc 25 sqcmincl dismantling complete complete all as specified and directed.

SCHEDULE 'A' PART - II FOR E/M PORTION

Taking down carefully copper/aluminum point wiring light/fan/sockets out let/power point complete (fittings such as switches, sockets, ceiling rose, pendent holders, light fittings etc. are to be measured separately) and/or drawing out from existing conduit/batten and making good disturbed surface of walls/floors/ceiling, complete all as specified and directed.

Material and labour for Point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS, 1100 volt grade with multi stranded copper conductor drawn through and incuding medium grade, ISI marked, including 20 mm dia concealed on wall/ceiling and incuding provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box/metal flush box with suitable steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally including provision of new 3 mm thick plastic laminated sheet top cover for housing the switches , socket outlets, fan regulators etc. with brass screws and brass washers and making good the disturbed surfaces as per existing for one light point controlled by one switch. Note :- Switch, socket and fan regulators to be measured and paid for separately.

All as per Srl item No.2.02 here in before but for one light point controlled by two way switch/ fan regulators

All as per Srl item No. 2.02 here in before but for one bell point controlled by one bell push .

All as per Srl item No. 2.02 here in before but for socket outlet point 5 Amp on same board.

All as per Srl item No. 2.02 here in before but for socket outlet point 5 Amp on Independent board.

All as per serial item No 2.02 above but with 4 sqmm cable for 3 pin 15 Amps switch socket outlet (Power point) complete all as specified and directed.

Supply and fixing modular switch 1 way 6 A module 230/250 volt , AC supply, ISI Marked, all as specified and directed.

Supply and fixing modular switch 1 way 16 A module 230/250 volt , AC supply, ISI Marked, all as specified and directed.

Supply and fixing modular bell push 1 way 6 A module 230/250 volt , AC supply, ISI Marked, all as specified and directed.

Supply and fixing modular switch 2 way 6 A module 230/250 volt , AC supply, ISI Marked, complete all as specified and directed.

Supply and fixing modular sockets 6A 2/3 pin combined 2 module 230/250 Volts, 50 Hz , AC supply, ISI Marked,all as specified and directed.

Supply and fixing modular sockets 6A/16A 2/3 pin combined 2 module 230/250 Volts, 50 Hz , AC supply, ISI Marked, all as specified and directed.

Supply and fix Modular PVC flush box 8 modules complete all as specified and directed.

Supply and fix Modular PVC flush box 6 modules complete all as specified and directed.

Supply and fix Modular PVC flush box 4 modules complete all as specified and directed.

Supply and fix Modular PVC flush box 3 modules complete all as specified and directed.

Supply and fix Modular PVC flush box 2 modules complete all as specified and directed.

Supply and fix Modular PVC flush box 1 module complete all as specified and directed.

Supply and fix Modular cover plate with frame 8 modules complete all as specified and directed.

Supply and fix Modular cover plate with frame 6 modules complete all as specified and directed.

Supply and fix Modular cover plate with frame4 modules complete all as specified and directed.

Supply and fix Modular cover plate with frame 3 modules complete all as specified and directed.

Supply and fix Modular cover plate with frame 2 modules complete all as specified and directed.

Supply and fix Modular cover plate with frame 1 module complete all as specified and directed.

Supply and fixing ceiling rose surface bakelite 65x50mm, 3 terminal complete all as specified and directed.

Supply and fixing call bell ding dong, AC, 230 V, Single pole ISI marked complete all as specified and directed.

Supply and fix LED batten fittings 1x18 / 20 Watt Warm white / white type Aluminium housing complete pre wired fixed to wall 6000 k with 2 nos PVC block of suitable size including taking down old unserviceable one . Make: Crompton-CCS-103-20-30-SL-DP-NWH WW / Bajaj Cat No BCLAB 20W WW/ Philips BN170CLED20S WW

Supply and fix wall mounted LED batten fittings with all accessories 1X 10 Watt Warm white / white LED 6000K , Aluminium housing integrated electronic driver and fixed to wall with 2 Nos PVC block suitable size complete all as specified and as directed including taking down old unserviceable light fittings Make- Crompton-LBHP-10-CDL/GE/LT / Bajaj BCLSB 10W WW/ Philips BN021LED12S WW

Supply and fix wall mounted LED foot light fittings with all accessories 10 watt foot light 6000K , Aluminium housing extruded polycarbonate, integrated electronic driver and fixed to wall with 2 Nos PVC block suitable size complete all as specified and as directed including taking down old unserviceable light fittings Make- Bajaj BLSGV9 w LED WW Pro / Crompton LSL6WW /Philips BWG150LED50-WW /

Supply and fix Wall bracket decorative LED Light fitting with lamp 10 Watt warm white Aluminium housing complete with necessary connection including taking down old unserviceable one.

Supply and fix Wall bracket decorative LED Spot light Light fitting with lamp 10 Watt Aluminium housing complete with necessary connection including taking down old unserviceable one Make: Crompton- CDR-211-09-40-SL-NWH / Bajaj BRDCSL9 watt WW / Philips RS378ZM55D75 WW

Supply and fixing of hot water Geysers of 25 ltrs capacity 5 star rated vertical type SS inner tank includng fixing of bolts , nuts grouted into the wall , and necessary cement work , making good of disturbed surface of wall , inculuding PVC connection pipe for hot and cold water 450mm long 15mm dia giving electric and water connection and testing after installation.

Supply and fix single pole and neutral enclosure with a two pin and earth plug and socket with one single pole MCB 240 Volt, 20 Ampr complete all as specifided and as directed

Supply and fix Exhaust fan 230 volts, 250mm sweep plastic body including making all electric connection complete all as specified and as directed including cutting of hole on wall and makng good disturbed surface of wall and outer wooden box for fan fix on wall complete all as specified and directed.

Supply and fix LED security Building light LED 35 Watt , pressure die cast aluminum housing, heat resistant glass, IP65 protection, better optics for uniform distribtion complete with all accessories internally pre wired and including connecting up with three core 1.5 sqmm flexible copper conductor cable from ceiling rose to connector of light complete all as specified and directed.

Supply and fix in repair MCB DB 4 way sheet metal enclosure TPN 415 volts, 50 Hz, with IP-43 protection, double door with 200 Amps standard bus bar of suitable size and common neutral link all enclosed in standard sheet flush mounting with MCCB 100 Amps incomer complete all as specified. (Note : (i) MCB SP/TPN shall be measured and paid seperately under appropriate items of this schedule . (ii) Copper thimble shall be used for connection of cable .

Supply and fix MCB Distribution board , 240 volts single pole and neutral ,double door, sheet steel, enclosure powder coated with 200 Amps rated busbar with neutral link, 12 ways , fixed on wall duly grouted in solid block wall or on wooden board with electrical connection, including taking down complete all as specified and directed.

Supply and fix MCCB TPN, 415 Volts, 40 to 100 Amps, 16 kA rupturing capacity complete all as specified and directed including taking down old one.

Supply and fix MCB four pole, 40 to 100 Amps, 10 kA rupturing capacity 415 Volts complete all as specified and directed including taking down old one.

Supply and fix MCB DP, 240 Volts, 40 Amps, 10 kA rupturing capacity 'C' series complete all as specified and directed including taking down old one.

Supply and fix in repair MCB, single pole 240 volts 6 to 32 Amps capacity fixed in DB's.

Material and labour Sub main wiring with two run single core 6 Sqmm FRLSH copper conductor cable PVC insulated, unsheathed, 1100 V including 20 mm dia concealed on wall/ceiling in PVC conduit, medium grade ISI marked with all accessories such as Tees, elbows, junction boxes etc, as required fixed on wall alongwith one run of 6 Sqmm single core PVC FRLSH insulated unsheathed copper conductor cable as continuous earth wire and connecting to existing main switch board / distribution board and testing on completion inculding taking down old wiring etc complete all as directed.Note: (i) four runs of 6 sqmm and one run of 6 sqmm cable and one run of PVC conduit shall be measured as one RM. (ii) Cutting of chases in the wall of appropriate size shall be carried out with electric cutter machine . (iii) Necessary plastering in the disturbed surface of wall and distempering /white washing to match the existing colour shall be included in the unit rate quoted.

Material and labour Sub main wiring with four run single core 6 Sqmm FRLSH copper conductor cable PVC insulated, unsheathed, 1100 V including 20 mm dia concealed on wall/ceiling in PVC conduit, medium grade ISI marked with all accessories such as Tees, elbows, junction boxes etc, as required fixed on wall alongwith two run of 6 Sqmm single core PVC FRLSH insulated unsheathed copper conductor cable as continuous earth wire and connecting to existing main switch board / distribution board and testing on completion inculding taking down old wiring etc complete all as directed.Note: (i) Two runs of 6 sqmm and one run of 6 sqmm cable and one run of PVC conduit shall be measured as one RM. (ii) Cutting of chases in the wall of appropriate size shall be carried out with electric cutter machine . (iii) Necessary plastering in the disturbed surface of wall and distempering /white washing to match the existing colour shall be included in the unit rate quoted.

Material and labour Sub main wiring with two run single core 4 Sqmm FRLSH copper conductor cable PVC insulated, unsheathed, 1100 V including 20 mm dia concealed on wall/ceiling in ISI marked with all accessories such as Tees, elbows, junction boxes etc, as required fixed on wall alongwith one run of 4 Sqmm single core PVC FRLSH insulated unsheathed copper conductor cable as continuous earth wire and connecting to existing main switch board / distribution board and testing on completion inculding taking down old wiring etc complete all as directed.Note: (i) Two runs of 4 sqmm and one run of 4 sqmm cable and one run of PVC conduit shall be measured as one RM.

Supply and fix in repair AC Three phase static energy meter of accuracy class 1.0 ,3 X 415 V ,50 Hz with Backlit LCD display of rating 10 - 60 A (measures and displays KWH ,V, Current I, KW, pf last month history of KWH, MD in KW) with special features like TOD, temper logging, optical communication port display in absence of power with transparent hinge type box. Note:- Old/retrived meter shall be deposited to MES store yard.

Supply and fix in repair AC single phase static energy meter of accuracy class 1.0 ,3 X 240 V ,50 Hz with Backlit LCD display of rating 10 - 60 A (measures and displays KWH ,V, Current I, KW, pf last month history of KWH, MD in KW) with special features like TOD, temper logging, optical communication port display in absence of power with transparent hinge type box. Note:- Old/retrived meter shall be deposited to MES store yard.

Supply and fix Factory made (Dust and power Jet Proof according to IEC 60529) opaque junction box of size 1200 x 400mmx 240 mm made of high quality polycarbonate (shock proof, rust free, corrosion free acid and chemical resistant, fire retardant having high impact (IK 08) totally insulated made of halogen and silica free recyclable material, UV resistant having high grade gasket made of polyurethane with copper terminal , with locking arrangement suitable for fixing TPN DB 4 way and energy meter single phase with glass for showing meter reading and 2 Nos M40 size cable gland and one M32 size gland suitable up to 16 Sqmm cable etc complete all as specified and directed including taking down old unserviceable junction box.

Material and labour for earthing complete with galvanised steel earth plate electrode 60 Cm X 60 Cm X 6 mm buried directly in ground vertically to a depth notless than 2.25 mtr deep below ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, check nuts and washers ,galvanised steel and protected by GI pipe 15 mm bore light grade & connected to main switch board or main control board as directed and including concrete pit in PCC (1:3:6) type C1, precast RCC (1:2:4) type B1 cover slab 30 cm X 30 cmX 5 cm with 10mm dia TMT bars 8 cm C/c both ways and one handle for lifting made out of 8 mm dia TMT bar, funnel, wire mesh, 20mm bore galvanised iron pipe (medium grade) for watering, charcoal or coke and salt in alternative layers, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown in Electrical Plate No 3 of SSR part -I.

Supply, laying, testing & commissioning in trenches, floors ,fix on wall/pole, passing through pipes etc.,LT UG cable , 1100 volts grade, PVC/ XLPE insulated, with multistranded aluminium conductors, armoured with galvanised steel wire or tape, gland, lugs etc, of size 25 Sq.mm 4 core, confirming to IS specifications.

Excavation in trenches not exceeding 1.5mtr. In depth and not exc 1.5mtr in width and getting out in soft/ loose soil for laying of cable etc complete all as specified and directed.

Returning ,fillling in trenches,spreading ,levelling,watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed.

Removing excavated material/ surplus soil and depositing where directed at a distence not exceeding 50mtr.at a level not exceeding 1.5 mtr from starting point complete all as specified and directed.

Supply lay/spread in trenches, river sand, clean, including spreading, levelling, punning for laying /cushioning of cables all as specified and as directed.

Supply & laying in trenches burnt clay building bricks, old size sub class “B” for cable protection complete all as specified and directed.

Supply, instatllation, testing & commissioning of Kitchen Exhaust System VASCO DHC 90 | Filter Less and Dry Heat Clean Technology | Matt Black Finish, Hassle free Filter Less and Dry Heat Auto Clean Technology, Thermostatic Touch Control Panel with 3 Speed Gesture Motion, including, Matt Black Finish, Black Metal Oil Collector,Motor with Copper Winding, Black Glass Clad Hood with LED Insignia, Front Panel with Black Glass, Energy Saving LED Light,Metal Blower + Metal Housing, Designed Air Flow (max): 1250 Nm3/h, Noise Level: 58 dBA (max), Lifetime Warranty, Size: 90 Cm complete all Civil work for fixing system, , make hole and replastiring esxiting wall with wall colour codeing with Basic Civil work required including fixing of Duct and complete Electrical wiring. as reqruied for system running complete all as specified and directed, Make -VASCO DHC or equivalent as approved by GE.

N.K.TRADING COMPANY

M/s Matadeen Ramchandra Agarwal

DNS CONSTRUCTION COMPANY

M/s Singh enterprises

M/S SHASS ENGINEERS

AMIT ASSOCIATES