Provision of Electrical skilled manpower for maintenance of E.I. work of V.I.P. floor and high level conferences meetings Parliament duties in Sanchar Bhawan New Delhi. Ch. to R M of E.I and Fans

SH-I Man Power

Provision of Manpower for smooth functioning of Electrical Maintenance & Operation of A.C, E.I, E/A Set, Sub Station, Lift, Compound Light, Pumps and Motors for water supply to the Bldg./colonies and offices etc. The manpower will work as electrical enquiry to receive complaints from Officers/residents of staff quarters/Offices at different locations and to attend the fault/restore the Power supply/ breakdown maintenance against the supply of material by the department except minor modification/ alternate arrangement, etc. complete in all respect to the entire satisfaction of Engineer-in-charge. Note:-Manpower may be asked to work at other locations also and in any shift without any extra cost as per requirement under the jurisdiction of EE(E) /SDE (E), BSNL. Decision of Engineer-in-charge will be final. Staff required(not above the age of 55 years) :-

Skilled Manpower having valid electrical licence/permit – 06 nos.

Unskilled Manpower capable to assist in all type of electrical works – 06 nos.

SH-II (Supply of Material/Items)

Replacement/Provision of following material for repairing & attending petty maintenance work by engaging adequate manpower as required at site for repairing of HT/LT panels, capacitor panels, existing wiring work like fluorescent fitting, ceiling fans, wall/pedestal fans, Main board, Sub Main board, Compound Lighting, water pumps & switchgears, Geysers, Split AC, water coolers, etc i/c dismantling, connection, fixing, testing etc as required. (NOTE-The material under replacement shall be similar to existing defective material or as per product directory and the dismental material will be property of the contractor. The rates should be quoted accordingly.).

5/6A Piano type Switches

15/16A Piano type Switches

5/6A 3/5 pin piano type Socket outlet

15/16A 3/6 pin piano type Socket outlet

5/6A Modular type Switches

15/16A Modular type Switches

5/6A 3/5 pin Modular type Socket outlet

15/16A 3/6 pin Modular type Socket outlet

Modular blanking plate

Single pole, blanking plate

Modular base & cover plate for 2 module

Modular base & cover plate for 3 module

Modular base & cover plate for 4 module

Modular base & cover plate for 6 module

Modular base & cover plate for 8 module

Modular base & cover plate for 12 module

ceiling rose

Bell Buzzer

Bell push switch

Stepped type Modular Fan regulator (2 module)

3 mm thick Hylam Sheet

Single pole MCB - upto 32A

SPN MCB- upto 32A

40A, 240V DP Isolator

63A, 240V DP Isolator

63A, 415V FP Isolator

100A, 415V FP Isolator

100 A, 16 KA, TPMCCB

Brass compression gland (19 mm) for 2 X 10 sq. mm 1.1 KV grade cable

Brass compression gland (28 mm) for 3.5 X 25 sq. mm 1.1 KV grade cable

Brass compression gland (32 mm) for 3.5 X 35 sq. mm 1.1 KV grade cable

Indicators

Capacitor - 2.5 MFD/ 3.5 MFD

Fan regulator - electronic step type

6A, 3 Pin, Polycarbonate Plug Top

16A, 3 Pin, Polycarbonate Plug Top

5/15Watt, 230Volt, 50Hz LED Lamps

Supply of Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable with piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.

Group 'C' in surface/ recessed steel conduit

Group 'C' in surface/ recessed medium class PVC conduit

Supply of Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.

Group 'C' in surface/ recessed steel conduit

Group 'C' in surface/ recessed medium class PVC conduit

Supply of following conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

20 mm Steel conduit

25 mm Steel conduit

20 mm medium class PVC conduit

25 mm medium class PVC conduit

25 mm PVC Flexible conduit

25 mm MS Flexible conduit

Supply of following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed steel/ PVC conduit as required.

2 x 1.5 sq. mm

3 x 1.5 sq. mm

6 x 1.5 sq. mm

3 x 2.5 sq. mm

3 x 4 sq. mm

6 x 4 sq. mm

2 x 1.5 Sqmm Twin Flat Cable-White

Rewiring Group -C for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable and 1.5 sq.mm FRLS PVC insulated copper conductor single core cable as earth wire in existing surface/recessed steel/PVC conduit including dismantling as required.

Supply of following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

150 mm X 50 mm X 1.6 mm thickness

300 mm X 50 mm X 1.6 mm thickness

Supply of suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supply of suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 Nos. 3 pin 5/6 A modular socket outlet and 2 Nos. 5/6 A modular switch, connections etc. as required.

Supply of suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connection etc. as required.

Supply of DP sheet steel enclosure on surface/recess along with 25/32 A, 240 V “C” curve DP MCB complete as required.

Supply of following sheet steel MCB DB, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc.as required. (But without MCB/RCCB/Isolator)

6 way , 240V SPN, Double door

12 way , 240V SPN, Double door

16 way , 240V SPN, Double door

4 way (4+12), 415V, Horizontal, TPN, Double door

8 way (4+24), 415V, Horizontal, TPN, Double door

4 way (4+12), 415V, Vertical, TPN, 200A tinned copper bus bar, Double door

Pdg. of 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Pdg. of 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Supplying of following sizes of pvc casing and capping for covering of loose wires etc.complete as reqd. (Make: AKG/ MK)

20mm x 12mm

25mm x 16mm

32mm x 16mm

Supplying of wooden type Extension board for operating of electrical apparatus having following polycarbonate electrical accessories including making inter-connection with suitable size of pvc insulated copper wire etc. complete as reqd. Wooden box of size 8"x13" with 3 mm thick phenolic laminated sheet, Switch 15 amp. - 2 Nos., Socket 15 amp. 6 pin - 2 Nos., Switch 5 amp. -2 Nos., Socket 5 amps. -2 Nos., 3C x 2.5 Sqmm Cu Flexible cable - 2 Mts., Plug Top 15 amps. - 1 No.

Supply of 6 Amp 4 outlet power strip controlled by common switch with surge protection suitable for 230 Volts, 50 Hz Single phase AC supply having connecting lead, safety fuse etc. complete as reqd. (Make: Havells/ Anchor/ Philips)

Supplying of PVC insulated, PVC sheathed copper conductor armoured cable of 1.1 KV Grade on surface/wall i/c making connections, testing etc complete as reqd.

3 x 1.5 Sq mm

3 x 4 Sq mm

Supply of following type heavy duty exhaust/ wall/ ceiling/ pedestal fans suitable for operation on 230V, 50 Hz single phase AC Supply i/c dismantaling/ refixing, minor civil works if reqd. making connection testing and commissioning etc complete as reqd. (Make: Almonard/ Crompton/ Havells/ Usha/ Orient)

250 mm sweep Plastic Ventilation Fan with front louvers

300 mm sweep Metallic Ventilation Fan with louvers

400 mm sweep, 1350 rpm, Plastic body wall fan

400 mm Sweep, 1350 rpm Pedastal Fan

1200 mm sweep, BEE 5 star rated, ceiling fan

Supplying of 9/10w, 6500K, 600mm long LED tube with batten/box LED Fittings on surface of wall/ below roof, connection with 3x1.5 Sqmm flexible wire, testing, commissioning etc. complete as reqd. (M/s Philips/ Havells/ Crompton/ Bajaj/ Twinkle]

Supplying of fancy type engagement light fitting having three sides metallic casing and glass/ PVC sheet cover at front including red & green 0.5w LED lamps (B-22 base), connections, testing etc. complete as required.

Remarks: 1.Manpower will be deployed by the agency at site to receive the complaints and for co-ordination for the work. For this, one mobile no. with whatsapp facility will be provided by the agency. 2. Adequate inventory of material will be kept at site by the agency for prompt attending the complaint. 3. Complaint received in Fore Noon will have to be attended by After Noon and complaints received in Afternoon will have to be attended by Forenoon of next day. Emergency complaints, if any, will have to be attended immediately at any time including odd hours. 4. Penalty of Rs. 500/- per complaint per day will be imposed for non-compliance of the complaint. If at any stage, it is observed that the performance of agency is not adequate, work will be rescinded, and the agency will be debarred from doing any work for one year in Delhi region. The work will then be carried out at his risk and cost without serving any notice 6. The Agency should quote amount keeping in view all Statutory requirements including minimum wages/ESI/EPF etc.

Note:- 1. 1. The Agency has to submit police verification record & ID proof of each staff. 2. The firm shall provide each staff with working cell phone. 3. The staff may be deputed for duty as per instruction of concerned SDE (E)/JTO (E). 4. Penalty shall be imposed in case of absence of any staff as per T & C of contract. 5. The GST / other Input Tax Credit (ITC) taxes shall be quoted by the firm as applicable as per latest amendments of GST Rules. 6. The contractor shall provide correct tariff heads & other details to enable BSNL claim Input Tax Credit. 7. Bidder must mandatorily quote for all GST components (CGST, SGST, and IGST) as required. 8. If annual maintenance contract charges are required to be quoted as per SOW, basic charges should be shown in column 4 & the Goods and Service Tax (GST) in column 7 to 12. 9. The bidder who submits the offer with concessional Goods and Service Tax (GST) shall submit the proof of applicable concessional GST. In case the Concessional GST is not creditable to BSNL it should be included in the price of the goods/services. 10. In case, dealer is registered under compounding scheme or any rule/notification where the BSNL is not eligible for input tax credit then the bidder should not disclose any amount in column 7 to12 & 14. 11. % age Rate of FF & Packing should be shown of basic unit price excluding all taxes & charges (i.e. as %age of col.4). 12. The FF & packing amount quoted shall not be subject to change after bid evaluation /ordering on account of change of copper, lead base price, change in duties & taxes of item etc. 13. Bidder must mandatorily mention HSN & SAC numbers. 14. Evaluation of bids: - The evaluation and comparison of responsive bids shall be done on the basis of Net cost to BSNL on the prices of the goods & Services (i.e. complete work) offered along with all applicable Taxes, packing Forwarding Freight & Insurance charges etc. exclusive of GST. Declaration by Bidder 1. We hereby declare that in quoting the above prices, we have taken into account the entire credit on inputs available under the GST Act introduced w.e.f. 1 July 2017 and further extended on more items till date. 2. We hereby certify that HSN/SAC shown in column 17 are correct & credit of GST for the amount shown in column 14 above are admissible as per GST Laws. Name of bidder: Seal of Company: GST No./(s)

STAR ELECTRIC WORKS

kashyap electricalsd

PRATEEK ELECTRICALS & EQUIPMENTS