GE 861 EWS-02 (T)/2025-26

Amount

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc. 15cm thickness below or above ground level (including floor finishes) complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store/credit complete all as specified and directed by Engineer-in-Charge.

M&L for 25 mm thick PCC in cement mortar (1:2:4) type B-0 (using 12.5 mm graded crushed stone aggregate) as in Sub-base of floor complete all as specified and directed by Engineer-in-Charge.

M&L for Non skid ceramic coloured joint free tiles 7 to 8mm thick (square/ rectangular), area of each tiles exceeding 0.18 but not exceeding 0.38 in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tiles, laid over and including cement screed bed 15 mm thick in cement mortar (1:4) for laying floor finish complete all as specified and directed by Engineer-in-Charge.

S&F coloured glazed wall tiles 350x250x7mm/450x350x7mm size and jointed in neat cement slurry and pointed with coloured cement to match as in vertical surfaces including 10mm thick rendering in cement mortar 1:4 on vertical surfaces to receive wall finishes complete all as specified and directed by Engineer-in-Charge.

M&L for 15 to 20mm thick granite slab (any type) in one piece machine cut bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

M&L for machine cut kota slab flooring 20-25 mm thick over and including 15 mm thick screed bed of cement mortar (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-in-Charge.

M&L for machine cut kota slab flooring 20-25 mm thick in one piece in riser of steps, skirting, dado and pillars, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete laid over and including 15mm thick rendering in cement mortar 1:4 on vertical surfaces to receive wall finishes complete all as specified and directed by Engineer-in-Charge.

Rounding to edges of stone slab on edge such as steps cooking platform and other similar situations complete all as specified and directed by Engineer-in-Charge.

M&L for 75mm thick, PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster on brick or concrete surfaces including raking out joints, hacking for key and scrubbing down with water complete all as specified and directed by Engineer-in-Charge.

M&L for 10mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finishing the surface even & smooth w/o using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for 15mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finishing the surface even & smooth w/o using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for applying two coats of OBD over one coat of alkali resistant primer (application of approved wall care putty 3mm thick to smooth & even surface) on new plastered surfaces including preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

Material and labour for applying two coats of OBD to old treated plastered surfaces of wall including preparation of surface (by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots) (application of approved wall care putty 3mm thick to smooth & even surface) with Chalk whiting, on plastered surfaces, preparatory to distempering complete all as specified and directed by the Engineer-in-Charge.

M&L for two coats of cement based paint over a coat of alkali resistance primer on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for two coats of cement base paint on old plastered surfaces of wall including preparation of surface complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connection including cleaning for refixing or removal to store, 15mm bore complete all as specified and directed by Engineer-in-Charge.

S&F 15mm bore GI tubing medium grade with all fittings fixed to walls ceiling or laid in trenches complete all as specified and directed by Engineer-in-Charge.

Fixing only 15mm bore GI tubing medium grade with all fittings fixed to walls ceiling or laid in trenches complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connection including cleaning for refixing or removal to store, 20mm bore complete all as specified and directed by Engineer-in-Charge.

S&F 20mm bore GI tubing medium grade with all fittings fixed to walls ceiling or laid in trenches complete all as specified and directed by Engineer-in-Charge.

Fixing only 20mm bore GI tubing medium grade with all fittings fixed to walls ceiling or laid in trenches complete all as specified and directed by Engineer-in-Charge.

Cutting into existing GI/CI tubing upto 50mm bore for making new connections including neceesary fittings etc. complete all as specified and directed by Engineer-in-Charge.

Dismantling water storage tanks of any description 1000 litres capacity and removing from site complete all as specified and directed by Engineer-in-Charge.

S&F for Rotational moulded polyethylene 1000 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20 mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 15 mm bore fancy type CP bib taps cast copper alloy with crutch or butterfly handle with chromium plated, handle, screwed down for iron pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 15 mm bore brass CP mixer for mixing hot and cold water screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipes complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 15 mm bore CP stop/angle valve cast copper alloy screwed down , high pressure with crutch or butterfly handle fancy type complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old painted wooden surfaces of any description not otherwise described for over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old painted steel surfaces of any description not otherwise described for over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new steel surfaces of any description not otherwise described for over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed by Engineer-in-Charge.

Dismantling plain or corrugated steel sheeting any gauge, thickness including roof covering etc. complete all as specified and directed by Engineer-in-Charge.

S&F for galvalume aluminium zinc coating GI based pre-painted corrugated steel sheets 0.50 mm thick of any colour having tensile strength of 550 Mps as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

S&F Pre-painted galvalume aluminium zinc coating GI based Plain steel sheets 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames not exc. 1.5 Sqm but with shutters (without taking off shutters from the frames) complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhat or frame with shutters (without taking off shutters from the frame) exceeding 1.5sqm and not exceeding 4.00 sqm each complete all as specified and directed by Engineer-in-Charge.

M&L for 2nd class hard wood, plain solid straight chowkhats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and directed by Engineer-in-Charge.

S&F Factory made solid PVC door frame of size 50mm x 47mm made out of 5 mm single side prelaminated PVC sheet reinforced with MS square tube manufactured as per SSR Part-I specifications and drawings complete all as specified and directed by Engineer-in-Charge.

S&F factory made solid PVC door shutters 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock rail and bottom rail on either side and gap insert for top rail and bottom rail panelling of plain colour PVC to sheet to be fitted in the MS frame welded / sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and directed by Engineer-in-Charge.

S&F 2nd class hard wood 35mm thick factory made plain framed panelled shutters with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial faces on both faces the size of rails and stile as per IS-1003 (Part-1) kiln seasoned and chemically pressure treated complete all as specified and directed by Engineer-in-Charge.

S&F for 30 mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass, gauge etc. windows/ventilators, divided into square with plain chamfered or rounded, mitred and rebated sash bars any numbers, provided with stiles and rails as specified in SSR part I section 8 clause 8.24 (b) complete all as specified and directed by Engineer-in-Charge.

S&F aluminium anodised barrel tower bolts extruded section of size 200 mm complete all as specified and directed by Engineer-in-Charge.

S&F aluminium anodised barrel tower bolts extruded section of size 75 mm complete all as specified and directed by Engineer-in-Charge.

S&F aluminium alloy, anodised, sliding door bolt of length 300 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of sections or cast-aluminium extruded alloy and fixed complete all as specified and directed by Engineer-in-Charge.

S&F butt hinges 100mm medium weight cold rolled mild steel and fixed complete all as specified and directed by Engineer-in-Charge.

S&F butt hinges 75mm medium weight cold rolled mild steel and fixed complete all as specified and directed by Engineer-in-Charge.

S&F mild steel 300mm size ordinary rat tail pattern springs including roller and roller plate complete all as specified and directed by Engineer-in-Charge.

S&F 150mm size aluminium door stopper complete all as specified and directed by Engineer-in-Charge.

Hacking out old or broken glass (any thickness size quality or description) from steel frames or stone concrete or brick surrounds glazed with putty or fixed with beads complete all as specified and directed by Engineer-in-Charge.

S&F 4mm thick sheet glass of ordinary quality and glazing with oil putty n.exc 0.5sqm in each pane complete all as specified and directed by Engineer-in-Charge.

M&L Vitrified Ceramic tiles, dark shade, 10mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge.

M&L for Vitrified tiles dark shade Granite /Marble /wood textures ceramic, 10 mm thick tiles in vertical surfaces or floors n.exe 0.36 Sqm over and including 10mm thick backing coat in cement mortar 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match .

M&L for Mirror polishing on marble/granite/Kota stone/stone work where ever required to give high gloss finish complete all as specified and directed by Engineer-in-Charge.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm complete all as specified and directed by Engineer-in-Charge.

S&F PVC valve less 10 litre capacity syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed by Engr-in -Charge.

S&F in repairs PVC valve less 10 litre capacity syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed by Engr-in -Charge.

S&F vitreous china wash down water closet pan ( pedestal pattern ) white complete including ‘P’ or ‘S’ trap , seat cover and fixing to flushing cistern, brackets, flushing pipe etc. complete all as specified and directed by Engineer-in -Charge.

S&F in repairs vitreous china wash down water closet pan ( pedestal pattern ) white complete including ‘P’ or ‘S’ trap , seat cover and fixing to flushing cistern, brackets, flushing pipe etc. complete all as specified and directed by Engineer-in -Charge.

Supply and fixing grating doom 125mm dia with waste hole of PTMT (weight not less than 40gms each) complete all as specified and directed by Engineer-in-Charge.

Taking down eaves gutters and rain water pipes 75/110mm dia including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning for refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) 110 mm bore pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) 75 mm bore pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed by Engineer-in-Charge.

S&F PVC bends 110 mm bore complete all as specified and directed by Engineer-in-Charge.

S&F PVC bends 75 mm bore complete all as specified and directed by Engineer-in-Charge.

S&F health faucet CP Brass hand Jet Shower 15mm bore dia and 1500mm long CP pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repairs health faucet CP Brass hand Jet Shower 15mm bore dia and 1500mm long CP pipe complete all as specified and directed by Engineer-in-Charge.

Preparation of new or untreated wood or wood based surfaces of any description exc.10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 0.63mm thick galvanized corrugated mild steel sheeting with two corrugation side lap fixed with ‘L’ or ‘J’ hooks as in roof covering complete all as specified and directed by Engineer-in-Charge.

S&F weather boarding in 2nd class hardwood clean sawn, plain, 20 mm thick or feather edges, 15 mm to 20 mm thick and fixed with 30 mm laps joints complete all as specified and directed by Engineer-in-Charge.

Demolition of wall and ceiling boards, weather boarding etc. (fibre or pulp insulation, wood etc.) or insulation boards/slabs including cover fillets etc. complete all as specified and directed by Engineer-in-Charge.

S&F for anodised aluminium snap grid of size 605 x605 mm frame work for false ceiling including straining with GI wire 4 mm thick complete all as specified and directed by Engineer-in-Charge.

S&F for 10 mm thick PVC insulation panels with EPS stuck to 1 mm thick plain PVC sheet suitably placed in false ceiling grid made of aluminium GI/MS as per specification and drawing complete all as specified and directed by Engineer-in-Charge.

S&F 6mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one faces, fixed with screw to timber frame work as on wall and ceiling complete all as specified and directed by Engineer-in-Charge.

M&L for 2nd class hardwood as in frame, scantlings etc, in any position including dismantling and taking down existing timber complete all as specified and directed by Engineer-in-Charge.

S&F for aluminium door of extruded aluminium section , consisting of frame vertical and horizontal members of size 100mmx45mmx 2.5mm thick with shutter stile 85mmx45mmx2.50mm thick , top middle and bottom rail of size 101.60mmx44.5mm with 5.50 mm thick tinted sheet glass and PVC prelaminated particle board 10 to 12 mm thick with aluminium beading and rubber gasket/beading including fixing of hydraulic floor spring one in single leaf or two nos in double leaf door. One mortice lock for aluminium door (each) and two Nos 200 mm long aluminium tower bolts and two nos aluminium handles D type for each door. Fixing with rawl plug including rectification of floor/wall to match the existing surfaces complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches not exceeding 1.50 mtr wide and n.exc 1.50 mtr in depth and getting out in hard/dense soil complete all as specified and directed by Engineer-in-Charge.

M&L for Cement concrete type D2 (1:4:8) using 40mm graded crushed stone aggregate in foundations, filling and mass concrete complete all as specified and directed by Engineer-in-Charge.

M&L for Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width, Type C1 1:3: 6 (20mm graded crushed stone aggregate) and setting in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

S & F for rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters etc. conforming to Fe 290 gde E 165 complete all as specified and directed by Engineer-in-Charge.

S&F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including cranking bending etc. complete & binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed by Engineer-in-Charge.

M&L for preparation newly plastered surfaces of wall and applying three coats of white wash complete all as specified and directed by Engineer-in-Charge.

S&F first class soft-wood in scantlings timber framed and fixed complete all as specified and directed by Engineer-in-Charge.

S&F Plain, 0.80mm thick galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed by Engineer-in-Charge.

M&L for Preparing new galvanised steel surfaces to receive painting, by coating with mordant solution including washing and cleaning, etc and applying two coats of synthetic enamel paint over a coat of primer red oxide zinc chrome on new galvanised steel surfaces complete all as specified and directed.

M&L for sand filling under floors or foundation complete all as specified and directed by Engineer-in-Charge.

Returning filling in including spreading, levelling, watering and well ramming in layers not exceeding 25cm in soil complete all as specified and directed by Engineer-in-Charge.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed by Engineer-in-Charge.

Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified and directed by Engineer-in-Charge.

M&L for RCC M-25 (Design mix) in foundations, including rafts footings, foundation beams, plinth beams, bases for column etc : basement slabs under-reamed piles and mass concrete complete all as specified and directed by Engineer-in-Charge.

M&L for RCC M-25 (Design mix) column, pillars, piers, post and struts complete all as specified and directed by Engineer-in-Charge.

M&L for RCC M-25 (Design mix) as in beams, cantilever, lintels over 1.5m span complete all as specified and directed by Engineer-in-Charge.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work for rough finished; concrete surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for use & waste of form work to sides of columns etc, complete all as specified and directed by Engineer-in-Charge.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchigs, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc also splays between floors and beams, etc. for rough finished concrete surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for formwork to soffits of floor or roof slabs, etc. for fair finished concrete surfaces complete all as specified and directed by Engineer-in-Charge.

S&F TMT bars 6mm to 8mm dia, cut to length bent to shape required including cranking bending spirally hooping for columns, hooking ends, binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

S&F round bars 10mm dia, cut to length bent to shape required including cranking bending spirally hooping for man hole handle, hooking ends, binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

M&L for brick work with sub class ‘B’ bricks straight or curved on plan exceeding 6m mean radius in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

M&L for brick work in half brick thick walls with sub class ‘B’ bricks straight or curved on plan exceeding 6m mean radius in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of newly plastered surface and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed by Engineer-in-Charge.

M&L for 3mm thick cement base white wall care putty in two coats (each coat not less than 1mm) and surface finished even and smooth with sand paper of complete all as specified and directed by Engineer-in-Charge.

M&L for 100mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub-base finished even and fair complete all as specified and directed by Engineer-in-Charge.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering and rolled/rammed to a true surface complete all as specified and directed by Engineer-in-Charge.

S&F mild steel work in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc confirming to Fe-290 Gde E-165 complete all as specified and directed by Engineer-in-Charge.

S&F 10mm thick mild steel Plates (plain or chequered) square cut or notched (ordinary and counter sunk) forming holes, welded including all necessary bolting or riveting etc. with roof trusses complete all as specified and directed by Engineer-in-Charge.

S&F for 0.63 thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed by Engineer-in-Charge.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including cement screed bed 15 mm thick in cement mortar (1:4) laying floor finish complete all as specified and directed by Engineer-in-Charge.

S&F mild steel box type steel windows with side hung shutters including projection type hinges with steel handle, tower bolt and steel peg stay, complete with glazing bars dovetailed or welded complete all as specified and directed by Engineer-in-Charge.

S&F mild steel box type steel windows with side hung shutters including projection type hinges with steel handle, tower bolt and steel peg stay, complete without glazing bars dovetailed or welded complete all as specified and directed by Engineer-in-Charge.

S&F Steel ventilators with top hung shutters including hinges, steel peg stay complete all as specified and directed by Engineer-in-Charge.

M&L Cement concrete 1:3:6 type C-0 using 12.5mm graded crushed stone aggregate as filling of pressed steel frames and hold fast block etc. complete all as specified and directed by Engineer-in-Charge.

S&F aluminium anodised barrel tower bolts extruded section of size 150 mm long complete all as specified and directed by Engineer-in-Charge.

S&F aluminium anodised barrel tower bolts extruded section of size 100 mm long complete all as specified and directed by Engineer-in-Charge.

S&F aluminium handle extruded fabricated type anodised of size 150 mm complete all as specified and directed by Engineer-in-Charge.

S&F aluminium handle extruded fabricated type anodised of size 100 mm complete all as specified and directed by Engineer-in-Charge.

S&F in floor stainless steel gratings , 125mm dia complete all as specified and directed by Engineer-in-Charge.

S&F 75mm PVC (SWR) vent cowl complete all as specified and directed by Engineer-in-Charge.

S&F 15 mm bore fancy type CP bib taps cast copper alloy with crutch or butterfly nuts with chromium plated , handle, screwed down for iron pipe complete all as specified and directed by Engineer-in-Charge.

S&F 15 mm bore CP stop/angle valve cost copper alloy screwed down, high pressure with crutch or butterfly handle fancy type complete.

S&F vitreous china wash basin white flat back size 550 x 400mm size, including cutting for and pinning in ends of brackets or erecting stand including of fixing of supply and waste pipe and 15mm pillar tap cast copper alloy with capstan head chromium plated complete all as specified and directed by Engineer-in-Charge.

S&F for 100mm bore cast iron sanitary connection for WC complete all as specified and directed by Engineer-in-Charge.

S&F for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed by Engineer-in-Charge.

S&F rotational moulded polyethylene 500 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball complete all as specified and directed by Engineer-in-Charge.

S&F for gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipes and fixed for bore of pipe 20mm complete all as specified and directed by Engineer-in-Charge.

S&F 15 mm size PVC connection with PTMT nuts of 600 mm long complete all as specified and directed by Engineer-in-Charge.

M&L for precast cement concrete 1:2:4 type B1 using 20 mm graded crushed stone aggregate for cover slab for Man holes/Septic tank set in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

S&F mild steel framed work as in doors or gates of angle or other section with gusset plate, rails braces etc, complete, drilling for fixing of steel sheeting, hanging, fastening and fixing complete all as specified and directed by Engineer-in-Charge.

M&L for 75 mm thick PCC (1:3:6) type C2 (using 40 mm graded crushed stone aggregate) as in sub base for receiving floor finishes etc. complete all as specified and directed by Engineer-in-Charge.

M&L for machine pressed precast concrete inter locking paver blocks WITH GREY CEMENT AND PIGMENT any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in coping, benching ,haunching complete all as specified and directed by Engineer-in-Charge.

M&L for laying in trenches 150mm dia reinforced concrete pipes, class NP3, laid and jointed in cement mortar 1:2 complete with collars complete all as specified and directed.

M&L for Concrete bed to drain pipes of 150mm dia pipes including packing under and haunching against sides with concrete after they are laid and tested; in cement concrete (1:3:6) type C2 (using 40mm graded crushed stone aggregate) complete all as specified and directed by Engineer-in-Charge.

M&L for PCC (1:2:4) type B-1, using 20 mm graded crushed stone aggregate as in benching to man holes etc. complete all as specified and directed by Engineer-in-Charge.

M&L for PCC (1:3:6) type B-1, using 20 mm graded crushed stone aggregate as in surface channels and drains etc. complete all as specified and directed by Engineer-in-Charge.

M&L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified and directed by Engineer-in-Charge.

Supply only integral water Proofing Compound complete all as specified and directed by Engineer-in-Charge.

M&L for construction of Brick work Septic Tank for 10 user capacity designed to carry sewage and sullage water, excavation in any type of soil, PCC (1:3:6) for base slab, Brick work with 230mm thick wall in cement mortar (1:3), 15mm thick cement plaster in cement mortar 1:3 mixed with water proofing compound on internal brick work surfaces, RCC 1:2:4 in Baffle walls and roof slab including beam etc. with vent shaft, manhole opening with cover connection etc, complete all as specified and directed by Engineer-in-Charge. Ref. Drawing No. CESZ/TD/1079/2011 dated 01.12.2011 sheet No. 1/1

M&L for construction of Soakage well including excavation in any type of soil, foundation in PCC 1:3:6 type C2, wells of honey combed and solid in M-25 concrete, including intercepting chamber, screen chamber Brick work in cement mortar, RCC cover slab in M-25, Filling with brick bats , complete of size (1.8 m dia x 3.0 M deep) complete all as specified and directed by Engineer-in-Charge. Ref. Drawing No. CESZ/TD-36/ST/20 Dated 22.02.20 Sheet No. 1/1 and 1/2

M&L for TMT bars 5mm dia and over upto and including 10mm dia in stirupps, spacers and binders but in stirupps complete all as specified and directed by Engineer-in-Charge.

M&L for broken stone hard core of gauge not exc. 63mm, deposited, spread and levelled rammed in layers not exc. 15cm thick, watered and well rammed to a true surface complete all as specified and directed by Engineer-in-Charge..

M&L for 100 mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate as in sub base, floors and pavings etc. complete all as specified and directed by Engineer-in-Charge.

Excavating over areas n exc 1.5 m deep and getting out in hard/dense soil complete all as specified and directed by Engineer-in-Charge.

Excavating over areas n exc 1.5 m deep and getting out in soft/distingrated rock complete all as specified and directed by Engineer-in-Charge.

Removing excavated soft/distingrated rock exc. 250m but n.exc 500m and depositing where directed complete all as specified and directed by Engineer-in-Charge.

Taking down carefully aluminium point wiring on TW Batten/in conduit / with conduit (light/Fan/socket or power) complete and making good the disturbed surfaces of wall/ceiling etc including taking down fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc and removing material from site complete all as specified and directed by Engineer-in-Charge.

Material and Labour for Concealed point wiring complete with 1.5 Sq.mm (nominal area) FR PVC insulated multi stranded copper conductor in and including heavy duty PVC conduit (wall thickness 1.6 mm) including fittings & accessories, with MS concealed terminal boxes with 3mm thick laminated bakelite ( Hylam/Anchor) sheet top cover for mounting switch, socket etc for one light/fan/bell point controlled by one switch and regulator with PVC cable copper conductor including 1.5 Sqmm solid copper conductor with green FR PVC insulation earth common earth dolly, complete all as specified and directed by Engineer-in-Charge.

All as per srl item No 148 above but for 3 pin socket out let 5 Amps on same board complete all as specified and directed by Engineer-in-Charge.

All as per srl item No 148 above but for 3 pin socket out let 5 Amps on independent board complete all as specified and directed by Engineer-in-Charge.

All as per srl item No 148 above but for 3 pin socket outlet 15 Amps with 2.5 Sqmm stranded copper conductor PVC unsheathed cable on independent board including PVC cable copper conductor 2.5 Sqmm with green insulator as earth wire with cast iron/pressed steel terminal box complete all as specified and directed by Engineer-in-Charge.

Supply and fixing switch piano flush type 5 Amp single pole one way complete all as specified and directed by Engineer-in-Charge.

Supply and fixing switch piano flush type 15 Amp single pole one way complete all as specified and directed by Engineer-in-Charge.

Supply and fixing socket outlet 5 pin 5 Amps flush type multi purpose complete all as specified and directed by Engineer-in-Charge.

Supply and fixing socket outlet multipurpose 2 in one, 6 pin 15 Amps flush type complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendant fittings complete all as specified and as directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engineer-in-Charge.

Supply and fixing ceiling rose surface type bakelite 65 x 50mm three terminals complete all as specified and directed by Engineer-in-Charge.

Supply and fixing sheet steel enclosure with double door, detachable gland plates flush/surface mounting for MCB’s fitted with bus bar, earth bar and neutral link 8 ways SPN 240 V complete all as specified and directed by Engineer-in-Charge.

Supply and fixing sheet steel enclosure with double door, detachable gland plates flush/surface mounting for MCB’s fitted with bus bar, earth bar and neutral link 12 ways SPN 240 V complete all as specified and directed by Engineer-in-Charge.

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) SPN 40 to 63 Amps complete all as specified and directed by Engineer-in-Charge.

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) SP 6 to 32 Amps complete all as specified and directed by Engineer-in-Charge.

Supply and fixing LED light fitting 1x9W/1X10W bulkhead luminaries including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing fan regulator electronic step type and making connection complete all as specified and directed by Engineer-in-Charge.

M&L for sub main wiring with two runs of single core PVC insulated, unsheathed copper conductor, multi stranded cable of size 4.00 Sqmm 1100 volts grade drawn through PVC concealed conduit of size 19/20 mm (ISI marked) including PVC accessories complete including cutting and chasing and making good etc. including one run of 4.00 Sqmm single core copper conductor multi-stranded PVC insulated, unsheathed cable as earth wire continuity conductor complete all as specified and directed by Engineer-in-Charge. Note : Two runs of 4.00 Sqmm cable and one run of 4 Sqmm cable as earth continuity conductor and one run of PVC Conduit shall be measured & paid as one unit.

Material and Labour for Sand filling in trenches or in foundations for cable protection including watering and consolidation complete all as specified and directed by Engineer-in-Charge.

M&L for laying common burnt clay building bricks Sub class B designation 75, old size complete all as specified and directed by Engineer-in-Charge.

Supply, laying and testing cable XLPE Insulated screened PVC bended, gavanised steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 35 sqmm 2 core complete all as specified and directed by Engineer-in-Charge.

M&L for Tubes galvanised Iron light grade supplied and laid in trenches/walls etc complete including all fitting of sizes 40 mm dia complete all as specified and directed by Engineer-in-Charge.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge.

Supply and fixing sheet steel enclosure with double door, detachable gland plates flush/surface mounting for MCB’s fitted with bus bar, earth bar and neutral link 4 ways SPN 240 V complete all as specified and directed by Engineer-in-Charge.

Supply and fixing for water heater storage type ( Geyser) Vertical type with inner container of capacity 25Ltrs, electrically operated, AC 230 volts, including 04 nos of hold fastner nuts of suitable size fixed in brick wall complete all as specified and directed by Engineer-in-Charge.

M&L for connection pipe (Copper) chromium plated 8 mm dia both end threaded including brass coupling bolt cone washer complete length of pipe not less than 450 mm suitable for Hot/cold water system complete all as specified and directed by Engineer-in-Charge.

Supply and fixing exhaust fan 300 mm sweep 900 mm, heavy duty, AC single phase 230/240 volts, metal body with louver shutters including making circular hole in existing wall to accommodate exhaust fan and necessary civil work and making good the disturbed surface complete all as specified and directed by Engineer-in-Charge.

Supply, laying and testing cable XLPE Insulated screened PVC bended, gavanised steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 10 sqmm 2 core complete all as specified and directed by Engineer-in-Charge.

Supply and fixing ceiling fans, complete with three blade, down rod, accessories 230V, 1200mm sweep, with Squirrel cage induction motor complete all as specified and directed by Engineer-in-Charge.

Material and Labour for replacement of earthing with galvanized iron earth plate electrode 600mm x 600mm, 6mm thick buried directly in ground vertically in a earth pit not less than 2.25mtr below normal ground level with top edge of the plate not less than 1.5mtr below normal ground level connected to GI earth wire 4mm dia by means of GI bolts, nuts, check nuts and washers (earth plate covered with alternate layers of charcoal dust and common salt 15cm thick), GI earth wire protected by GI pipe light grade 15 mm dia upto switch board and connected to main switch board including provision of GI pipe 20 mm dia light grade watering pipe with funnel and wire mesh, all as shown in Electrical Plate No. 3 of SSR Part-I, including PCC chamber (1:3:6) using 20mm graded stone aggregate and CI cover and frame including all necessary excavation and earth work and taking out old earthing complete all as specified and directed by Engineer-in-Charge.

M/S HAFIZ AND SONS (BID ID -3295885)

MS BHAT BROTHERS (BID ID -3299148)

M/s Pall Constructions (BID ID -3299357)

FIRDOUS AHMAD BABA (BID ID -3304308)

Concept Engineering & Constructions (BID ID -3304520)