GE/863/EWS-T-67 OF 2021-22

Amount

Taking down cement plastering at any description on brick or stone wall etc including raking out joints hacking for key scrubbing down with water etc and removal of debries and depositing where directed complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness, including cover fillets complete all as specified and directed.

Dismantling timber scantlings under 40 sq.cm in section, in any positions as in framed work, but in fillets, rails, posts, rafters, purlins, etc complete all as specified and directed.

Dismantling of Plain or corrugated steel sheeting, Pre-painted galvalume aluminium zinc coating sheets of any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

Taking down chowkhats or frames not exc 1.5 sqm each with shutters without taking off shutters from the frame, including iron/aluminium mongery and removing from site, including cutting holes for taking out hold fasts and making good disturbed protion in cement mortar (1:3) or PCC 1:2:4 type B1 (after inserting new hold fast if required), compete all as specified and as directed. Note:(Hold fast shall be measured and paid seperately).

Taking down chowkhats or framesexc 1.5 sqm but not exceeding 4 sqm each with shutters without taking off shutters from the frame, including iron/aluminium mongery and removing from site, including cutting holes for taking out hold fasts and making good disturbed protion in cement mortar (1:3) or PCC 1:2:4 type B1 (after inserting new hold fast if required), compete all as specified and as directed. Note:(Hold fast shall be measured and paid seperately).

Taking down Shutters of any description n.exc 1 sqm each including iron/aluminium mongery and removing from site complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each including iron/aluminium mongery and removing to store complete all as specified and directed.

M&L for 12mm thick rendering in cement mortar (1:6) on brick work or concrete surfaces finished even and smooth without using extra cement, complete all as specified and directed.

M & L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement mortar 1:4 using integral water proofing compound 3% by weight of cement and finished even and smooth (without using extra cement) complete all as specified and directed. Note :- Integral water proofing compound to be measured and paid separately as supply only.

M & L for rendering 15mm thick on stone masonry surface or surface other than fair face of brickwork or on one side of lathing in cement mortar 1:4 using integral water proofing compound 3% by weight of cement and finished even and smooth (without using extra cement) complete all as specified and directed. Note :- Integral water proofing compound to be measured and paid separately as supply only.

Supply only integral water proofing compound complete all as specified and directed

M&L for 40 mm thick ,PCC (1:2:4), type B-1 using 20mm graded stone aggregate as in floor, including rough finished with out using extra cement complete all as specified and directed.

M&L 50mm thick Cement concrete, type C2, 1:3:6 (using 40 mm graded stone aggregate) in plinth protections, finished even and smooth without using extra cement complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 type B0 using 12.50mm graded stone aggregates as in base of flooring, including rough finished without using extra cement complete all as specified and directed.

M & L for non skid coloured ceramic tiles 7 to 8mm thick square / rectangular area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floor laid over and including 15 mm thick screed bed in Cement Mortar 1:6 as in floor etc. set and jointed in neat cement slurry and pointed in coloured cement to match colour tiles complete all as specified and directed.

M & L for non skid coloured ceramic tiles 7 to 8mm thick square / rectangular area of each tile exceeding 0.18 sqm and n.exc 0.36 Sqm as in floor laid over and including 15 mm thick screed bed in cement mortar 1:6 as in floor etc. set and jointed in neat cement slurry and pointed in coloured cement to match colour tiles complete all as specified and directed.

M&L for Vitrified ceramic coloured tiles 10mm thick square/rectungular, polished, area of each tile exceeding 0.35sqm but not exceeding 0.42sqm in floor laid over and including 15 mm thick screed bed in cement mortar 1:6 as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M & L for Coloured Glazed ceramic tiles 200 x 300 x 7 mm thick, on vertical surfaces such as skirting, dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M & L for Chequered cement concrete tiles 300 x 300 x 25 mm thick, Set jointed and pointed neat cement slurry with grey cement & pigment laid over and including 15 mm thick screed bed in cement mortar 1:6 as in floor etc. set and jointed in neat cement slurry and pointed in white or Coloured cement to match complete all as specified and directed.

M & L for second class hardwood clean sawn scantlings as in timber framed and fixed complete all as specified and directed.

M & L 6 mm thick Ply wood, grade BWR, type BB fixed with screws to timber frame work in partitions/ shutters, ceiling etc complete all as specified and directed.

M & L 6 mm thick Ply wood, grade BWR, type BB fixed with screws to timber frame work in partitions/ shutters, wall etc complete all as specified and directed.

S & F for 0.63mm Galvanized, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275, complete all as specified and directed.

All as per item no. 26 above but except sheeting (any thickness) sheet shall be used as obtained from serial item No 06 here in before

S & F 0.63 mm thick Plain Galvanized, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) complete all as specified and directed.

S & F for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Material and labour, 2nd class hard wood (Hollock), plain, solid, straight chowkats and frames wrought, framed rebated on the solid rounded for chamfered, put together with glue pinned at joints, complete all as specified and directed.

S & F 35mm thick Second class hard wood Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers supplied and fitted to Chowkat complete all as specified and directed.

S & F 35 mm thick second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars) chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in SSR Pt I Section 8, clause 8.24 (a) complete all as specified and directed.

S & F 30 mm thick second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars) chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in SSR Pt I Section 8, clause 8.24 (b) complete all as specified and directed.

S & F Galvanized mild steel wire cloth, 0.63 mm dia of wire and average width of aperture 1.18 mm and fixed with tinned stacks, or galvanized wire staples complete all as specified and directed.

S & F plain sheet glass/pin headed glass of 3 mm thick in Squares not exceeding 0.50 Sqm in each pane with oil putty and clips complete all as specified and directed.

M&L for preparation of new or old surface of wood and wood based material, treating ends of posts, backs of chowkats, etc., area tarred exc 0.1 sq. m but n exc 0.5 sq. m each treated with tar or coal tar black paint complete all as specified and directed.

M & L for treating small articles such as stop, covers, gully gratings, holdfasts, ends of posts, backs of chowkats, etc., area n exc 0.1 sq. m each, treated with tar or coal tar black paint complete all as specified and directed.

S & F mild steel works in bands, straps, supports, stays, bolts, hooks, hold fast etc, similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

S & F Aluminium barrel tower bolt of 100mm long stove enamelled black with bright bolt complete all as specified and directed.

S & F Aluminium barrel tower bolt of 75mm long stove enamelled black with bright bolt complete all as specified and directed.

S & F 300 mm long Aluminium alloy, anodized, sliding door bolt with hasp staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of truded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S & F 75 mm long extruded mild steel Butt hinges with galvanized mild steel and fix complete all as specified and directed.

S & F 100 mm long extruded mild steel Butt hinges with galvanized mild steel and fix complete all as specified and directed.

S & F Aluminium alloy pressed handle oval type stove enamelled black of 125mm long fixed with screw to shutter complete all as specified and directed.

S & F Aluminium alloy pressed handle oval type stove enamelled black of 75 mm long fixed with screw to shutter complete all as specified and directed.

S&F for IInd Class hard wood of Small fittings such as brackets of any type, latch and hing blocks, shaped door & window stops and the like including all necessary labours; articles n exc 200 cu.cm each complete all as specified and directed.

S&F for IInd Class hard wood of Small fittings such as brackets of any type, latch and hing blocks, shaped door & window stops and the like including all necessary labours; articles exc 200 cu.cm each complete all as specified and directed.

S & F 300mm MS ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

M & L for preparation of new plastered surface of wall and applying two coats of distemper oil emulsion over coat of chalk whiting on walls complete all as specified and directed.

M & L for preparation of new plastered surface of wall and applying two coats of cement base paint with alkali resistant priming paint complete all as specified and directed.

M&L for preparation of New or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of Pink primer complete all as specified and directed.

M & L for preparation of old painted steel surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint (first quality) complete complete all as specified and directed.

M&L for preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of steel surface complete all as specified and directed .

Note:- The total shall subject to adjustment of credit of Rs 40340.00 for old Materials as per Schedule of Credit.

M/S Gopal Singh

M/S Shamsher Negi Dewa