Special repair of renovation of main building of B.K Hospital Civil Hospital NIT Faridabad

Amount

Demolishing mud phaska in terracing and disposal of material cum within 50 metres lead [HSR 5.11]

Demolishing brick tile covering in terracing including stacking of sqm serviceable material and disposal of unserviceable material within 50 metres lead. [HSR 5.14]

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead: Of area 3 sq. metres and below [HSR 5.29.1]

Dismantling cement conglomerate / terrazzo floors 25 mm to 50 sqm manually/ by mechanical means and disposal of material [HSR 5.42] within standard lead as per direction of Engineer- in-charge.

Removing white or colour wash by scrapping and sand papering sqm and preparing the surface smooth including necessary repairs to scratches etc. complete [HSR 30.21]

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. [HSR 5.45]

Removal of old broken glass panes (any thickness or size, quality or description) from wooden frames, glazed with putty or fixed with beads [HSR 5.50]

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 1O mm to 25 mm [HSR 5.43.1]

Cement Concrete 1 :8:16 with Over burnt (Jhama) Brick Aggregate: 90 mm to 40 mm size in foundation and plinth [HSR 10.100.1].

Reinforced cement concrete work in beams, suspended floors, cum roofs having slope up to 15 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor four level, excluding the cost of centering, shuttering, finishing and reinforcement with 1: 1.5:3 (1 cement : 1.5 coarse sand(zone-111) : 3 graded stone aggregate 20 mm nominal size) [HSR 6.16]

Centering and shuttering including strutting, propping etc. and removal of form for [HSR 6.30.1] Foundations, footings, bases of columns, etc. for mass concrete

Brick work with common burnt clay non-modular bricks of class designation 10.50 in foundation and plinth in: Cement mortar 1:4 (1 cement: 4 coarse sand) [HSR 7.21.1]

Providing and laying brick tiles over mumty roofs, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over 12 mm layer of cement mortar 1:3 (1 cement :3 fine sand) and finished neat: With common burnt clay non-modular brick tiles of class sqm designation 1 O [HSR 9.14.1]

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand: 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1 :3 (1 cement : 3 fine sand) as per standard design : [HSR 9.17.1] In 75x75 mm deep chase

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS: 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x1 Ox0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering up to 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charae but excludina the cost of oaintina with 9.46.1 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) [HSR 9.46.1].

Providing and fixing of Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 ( 1 cement : 4 coarse sand) : [HSR 10.37.1] 25 mm thick

Laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.06% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of Tile 600x600 mm [HSR 10.71.2] Labour Rate

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1 :4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete [HSR 10.59]

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1 :3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.[HSR 10.58]

Laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1 :4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-inCharge: 10.49.1 Flamed finish granite stone slab Jet Black, Cherry Red, Elite sqm 317 1652 1970 Brown, Cat Eye or equivalent [HSR 10.49.1] Labour Rate

12 mm cement plaster of mix :1:4 (1 Cement:4 fine sand) [HSR 11.5.3]

15 mm cement plaster on the rough side of single or half brick wall of mix :1:4 (1 Cement:4 fine sand) [HSR 11.6.1]

Pointing on brick work or brick flooring with cement mortar 1 :3 (1 cement : 3 fine sand): Flush / Ruled/ Struck or weathered pointing [HSR11.25.1]

Applying pink primer or aluminium priming coat on wood work including preparation of surface, Knotting and stopping etc. [HSR 11.77] Labour Rate

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade [HSR 11.78] Labour Rate

Applying priming coats with primer of approved brand and manufacture, having low voe (Volatile Organic Compound ) content.: With water thinnable cement primer on wall surface having voe content less than 50 grams/litre [HSR 11.69.2] Labour Rate

Wall painting with (bio grade)plastic emulsion paint of approved brand and manufacturer to give an even shade (two or more coats) Generally used in hospital buildings etc. complete as per Specifications. [HSR 11.123] Labour Rate

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade: [HSR 11.64.1] New work (two or more coats) over and including water thinnable priming coat with cement primer- Labour Rate

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gmnitre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. [HSR 11.98.1] New work (Two or more coats applied@ 1.43 litre/ 10 sqm Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm Labour Rate

Applying two coats white cement based putty of approved brand and manufacturer, over plastered surface and grinding the surface smooth with sand paper to get en even and smooth finish including cost and carriage of all material , labour charges, scaffolding, sundries etc. complete [HSR 11.58] Labour Rate

Providing and fixing wooden handrail of required shape and design, with necessary screws, including labour, for rounding, vertical and horizontal bends and curves complete fixed in position - commercial hard wood, such as Hallock, champ, chikrassy cum and chaplash, etc., (Non- coniferous timber other than teak, conforming to I.S. specification no.1003,kiln seasoned) [HSR 12.113.2]

Providing and fixing skirting with Pre-laminated (one side decorative and other side balancing lamination) flat pressed 3 layer or graded particle board (medium density) Grade I, Type II, IS :12823 marked, with necessary fixing arrangements and screws, including drilling necessary holes for rawl plugs etc. and priming coat on unexposed surface complete – 25 mm thick [HSR 8.21.2]

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) : Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) [HSR 12.157.1.1]

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) [HSR 12.157.2.1] Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade I Type II, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides [HSR 12.158.2]

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) [HSR 12.159.2]

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. [HSR 13.29.2] In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing hard drawn steel wire fabric of size 75 x25 mm mesh or other suitable size wire mesh to be fixed & firmly anchored to the concrete surface by means of "L" shaped mild steel shear key welded with existing reinforcement including the cost of materials, labour, tool & plants as approved by Engineering-charge [HSR 31.1]

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 2.0 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 2.00 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:: Profile B [HSR 13.3.1.1] Fixing with adjustable lugs with split end tail to each jamb

Fixing C.P. brass bib cock of approved quality conforming to IS:8931 – 15 mm nominal bore [HSR 22.104] [Labour Rate]

Fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. – 15 mm nominal bore [HSR 22.106.1] [Labour Rate]

Fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931- 15 mm nominal bore [HSR 22.107.1] [Labour Rate]

Providing and fixing Un-plasticized P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour-15 mm nominal bore with 30 CM length [HSR 22.128.1]

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS: 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. [HSR 22.181]

Fixing white vitreous chinaware pedestal for wash basin completely recessed at the back for the reception of pipes and fittings [HSR 22.5] Labour Rate

Fixing white vitreous chinaware flat back or wall comer type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: Range of three urinal basins with 101itre white P.V.C. automatic flushing cistern [HSR 22.25.4] Labour Rate

Fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- White vitreous chinaware Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer [HSR 22.2.1] [Labour Rate]

Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. [HSR 22.209]

Fixing toilet paper holder:- C.P Brass [HSR 22.42.1] (Labour Rate]

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. [HSR 22./85] Internal work- Exposed on wall (i) 40 mm nominal outer dia pipes [HSR 22.85.5]

50 mm nominal outer dia pipes [HSR 22.85.6]

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc [HSR 22.86] (i) 20 mm Nominal outer dia pipes [HSR 22.86.2]

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : [HSR 22.103] (i) 15 mm nominal bore [HSR 22.103.1]

20 mm Nominal Bore [HSR 22.103.2]

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. [HSR 22.109]

Recovery Items : - Bidders have to quote rates for recovery items atleast or more than reserve price. The rates quoted against recovery items will not be including in the total amount. Rather rate will be deducted while calculating financial statement of the Agency. Note : - The reserve amount if minimum amount to be used as base for quoting purchase rate by the Agency. No rates below the reserve price will be entertained and reserve rise will be considered for all purposes in case the agency quotes lesser than reserve price as under:- (i) Brick Tiles @ 5 Each

Doors @ 1000/- Each

Windows @ 750/- Each

M/S NANAK CHAND AND SONS