SPECIAL REPAIR TO CERTAIN JCOs/OR MD ACCN AT DIGIANA GRN OF BD BARI MIL STN UNDER GE KALUCHAK

Amount

Taking down cement plaster on bricks or stone wall/ decayed surfaces of concrete from roof projectiokn or RCC Chajjas etc. including racking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and as directed.

M&L rendering 15 mm thick on fair faces of brick work or concrete surfaces in cm 1:6 finished even and smooth (with out using extra cement) complete all as specified and as directed.

M&L Rendering 15 mm thick on fair faces of brick/concrete surfaces in cement plaster 1:4, using water proofing compound mix as per manufacturer detail, finished even and smooth without using extra cement, complete all as specified and as directed.

M&L Rendering 5mm thick on concrete surfaces in CM 1:3 finished on even and smooth without using extra cement as in ceiling, Chajja etc.incl taking down old plaster complete all as specified and as directed.

M&L for capillary rise treatment of walls, Base coat: Berger HS Latex plus(or equivalent) Consumption base coat: 0.3 kg/m2 Second and Third coat: Latex sheild 2K(or equivalent) Consumption top coat: 3 kg/m2 System requirements: density: 2.00 kg/ltr; compressive strength: 0.5 N/mm2. complete all as specified and as directed.

Material & Labour for RCC chajja/fascia/parapet repair by using following steps :- (a) Removal of existing concrete along with loose damaged and cracked concrete/cover concrete from chajjas etc, exposing corroded steel reinforcements upto a depth of 10mm minimum behind the reinforcement by chipping/hacking with chisel and hammer or by mechanical means like chisel hammer, pneumatic chippers including high pressure water jetting to chipped concrete and reinforcement all as directed by Engineer-in-charge. Hard concrete shall not be removed. However if the rebar is corroded, concrete around it shall be removed. (b) Cleaning the surface of reinforcement bars from dust by using wire brushes and dry cloth and applying FOSROC Rebakleens RR- Rust Remover or equivalent using small brush and allow to react it for 16-24 hrs. (c) Providing and applying two coats of Fosroc Nitozinc Primer - two component, zinc rich epoxy, anti-corrosive protective coating or equivalent by brushes to the exposed and cleaned rebars with an interval of 45minutes to 1 hour @ 40microns DFT / coat and allowed to completely dry for 24 hours complete all as specified and as directed.

Supply only Integral water proofing compound liquid complete all as specified and as directed.

Taking down chowkats or frames n. exc. 1.5 sqm each but with shutter without taking off shutters from the frame. complete all as specified and as directed.

Taking down chowkats or frames exc. 1.5 sqm & not exceeding. 4 sqm each but with shutter without taking off shutters from the frame. complete all as specified and as directed.

Pressed steel frame for door with one or more rebates including necessary lugs, fixing lugs hinges, lock strike plate etc. of size 125mm x 60 mm and made of 1.25mm thick MS sheet, complete all as specified and directed including necessary welding complete and including medium weight 03 Nos of MS butt hinges of size 75mm / 100mm / 125mm and 01 No 50mm Size of medium weight MS butt hinge complete all as specified and directed complete all as specified and as directed.

Pressed steel frame for door with one or more rebates including necessary lugs, fixing lugs hinges, lock strike plate etc. of size 105mm x 60 mm and made of 1.25mm thick MS sheet, complete all as specified and directed including necessary welding complete and including medium weight 03 Nos of MS butt hinges of size 75mm / 100mm / 125mm and 01 No 50mm Size of medium weight MS butt hinge complete all as specified and as directed.

M&L PCC 1:3:6 type C - 1 (using 20 mm graded crushed stone aggregate) as in back filling of chowkats and bed blocks for hold fasts etc complete all as specified and as directed.

M&L 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides with both face is covered with deco rative face veneer with lipping/frame to match complete all as specified and as directed.

S&F 35mm thick 2nd class hard wood Glazed and skeleton shutters open rebated & prepare to receive glass, gauge etc (without sash bars /edges of framing plain chamfered or rounded, fitted with cut and mitred beds for securing glass etc) size of members of shutters as spd in SSR Part-I section-8 clause 8.2 (A). complete all as specified and as directed.

Solid PVC door/cup board frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling and fixing in opening. complete all as specified and as directed.

S&F factory made solid PVC moulded door shutter with wood free EPS 28 to 30mm thick (Stile) with flush panel with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face complete all as specified and as directed.

Steel ventilator with top hung shutter including hinges, steel peg stay, lugs as in hold fast with locking arrangements, complete all as specified and as directed.

Steel windows with side hung double shutters (window consisting of two shutters out side and two shutters of similar dimension inside of single MS Frame) box type hinges with steel handle of 100mm and steel peg stay, complete with glazing bars, and including MS guard bars and grills made out of 10mm MS square bar (Grill and guard bars shall be provided as per directions of Engr-in- Charge during execution of work) dovetailed or welded complete all as specified and as directed.

Factory made box type steel windows comprised of tubular frame and shutters made out of 1.25mm thick MS sheet tube with double side shutters (Wire Gauged shutter and Glazed Shutter), side hung shutters with MS handles and MS stays dovetailed or welded including 02 nos MS Tower Bolt 150mm long for each leaf, 8 mm square guard bars at spacing as shown in drawings, MS flat iron frame work, MS hinges, tarred hold fast, PCC 1:2:4 type B1 as in bed of hold fast, 01 No. per leaf of stopper of 100mm size, one coat of red oxide zinc chrome primer etc, complete all as specified and shown as drawing No. CEPZ/TD-354/09 sheet 1/3 to 3/3.Note : a). Wire cloth and Sheet glass shall be measured and paid seprately under respective items. b). Rate of both type of shutters is inclusive in the quoted rate. complete all as specified and as directed.

S&F Galvanized mild steel wire cloth 0.45 nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tank or galvanized wire staple complete all as specified and as directed.

Sheet glass, ordinary quality, 3mm thick and glazed with oil putty or wooden beads, in square n exc. 0.5 Sq m each pane, complete all as specified and as directed.

3mm thick figured glass, pin head type and glazing with oil putty or wooden beads in square not exceeding 0.5 sqm each complete all as specified and as directed.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (both type) 300mm longh, and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

S&F Aluminium anodised 150mm long barrel tower bolt of extruded section and fixing complete all as specified and as directed.

S&F Aluminium handles cast type anodised 150mm complete all as specified and as directed.

Butt hinges 100mm medium weight stainless steel complete all as specified and as directed.

Aluminium anodized barrel tower bolt of extruded section and fixed complete of size 125 mm long complete all as specified and as directed.

Aluminium handle cast type anodized of size 100mm complete all as specified and as directed.

Floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel springs, fixed in floor with over all length of cover plate 150mm complete all as specified and as directed.

Dismantling floor,hearth or wall tilling,cement mortar bedding(but including backing) , terrazzo toping complete all as specified and as directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to emove dust, etc and Brushing neat cement slurry with 3.0kg of cement per complete all as specified and as directed.

M&L Virified Ceramic tiles 10 mm thick in light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match complete over 15mm screed bed or beading layer in CM 1:6 complete all as specified and as directed.

M&L Virified Ceramic tiles 10 mm thick in light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in dado, Skerting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick cement plaster in CM 1:3 complete all as specified and directed.

S&F Coloured non skid ceramic tiles 300 x 300 x 7/8 mm thick,(squre/rectangular) in floors area of each tiles exceeding 0.06 sqm but not exceeding 0.11 sqm set and jointed in neat cement slurry and pointed in white or Coloured cement to match over 15mm screed bed or beading layer in CM 1:6 complete all as specified and as directed.

M&L Glazed ceramic coloured tiles 450x300mmx7mm thick for work vertical surfaces such as shirking/dado and risers to step etc set and jointed in neat slurry and pointed in white /coloured cement and pigment to match the tiles over and including 10mm thick cement plaster in CM 1:3 , complete all as specified and as directed.

M&L 18 to 20mm thick black Granite stone (table rubbed and polished) in cooking plateform bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone over 15mm thick screed bed in CM 1:4 after roughing surfaces of old concrete floor by picking sweeping down with water to remove dust etc including cutting holes into or through reinforced cement concrete slabs , for gas pipe (Superficial area exc 100 sq cm but n. exc. 250 sq cm. complete all as specified and as directed.

M&L Machine cut kota stone slab flooring/Stair,skirting and dado 20-25mm thick over cement screed bed laid and jointed cement screed bed laidand jointed with grey cemant slurry mixed with pigment to match the shade of slab including rubbing and polishing complete for floor/ tread/riser of staircase over and including15mm thick screed bed in CM 1:6 after roughening surface of old concrete floor by picking sweeping clean and washing down with water to remove dust and brushing neat cement slurry with 3.0 kg cement per sq. metre incl marble strip design as per complete all as specified and as directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed.

20mm dia PVC coated drapery rods in one length per door/window, fancy type (engraved rods), designed & coloured as approved by GE providing with two nos of Bracket powder coated for holding curtain rod and Fiber fancy dome type or wall to wall fixed in repair complete all as specified and as directed.

S&F 300mm ordinary rat tail mild steel rod pattern springs incl roller and roller plate complete all as specified and as directed.

Dismantling water tanks exceeding 250 ltr capacity but not exc 500 ltrs complete all as specified and as directed.

Rotational molded polythene water storage tank vertical type with closed top hoisted and fixed in position all as spd in SSR part-I capacity 500 litter . complete all as specified and as directed.

S&F in repair 20 mm ball valves high pressure of PTMT with epoxy coated , aluminium rod & high density plastic ball screwed for iron pipe min wt 210 gms. complete all as specified and as directed.

Taking up or down 15 mm steel tubing and connections including clearing for refixing or removal to store. complete all as specified and as directed.

Taking up or down 20 mm steel tubing and connections including clearing for refixing or removal to store. complete all as specified and as directed.

S&F Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore dia15 mm, complete all as specified and as directed.

S&F Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore dia 20 mm, complete all as specified and as directed.

Refixing old steel tubing and connections in new or old position with all fittings retrieved from Serial here-in-before and fixed (walls, ceiling, floors, etc) of 15 mm dia complete all as specified and as directed.

Refixing old steel tubing and connections in new or old position with all fittings retrieved from Serial here-in-before and fixed (walls, ceiling, floors, etc) of 20 mm dia complete all as specified and as directed.

S&F Vitreous china water closet Orissa pattern long pan size 580x440mm with trap front or back inlet and integral foot rest complete fixed in repair including lime concrete bedding and connection to drain or outgoing pipe and to flushing pipe and anti siphon pipe complete all as specified and as directed.

S&F PVC flushing cistern white shade low level 10 ltrs capacity, white with inlet ball valve, float and handle including bracket and flush pipe including connection to pipes, fixed in repairs complete all as specified and as directed.

S&F PVC connection 15 mm size with PTMT nuts of length 600 mm complete all as specified and as directed.

Tubular towel rail, brass chromium plated, 20 mm dia, D type, 60 cm long between Hangs, fixed in repairs complete all as specified and as directed.

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brickets and connecting union to pipe overall size 915mmx460mm bowl size 410mmx330mmx160mm. complete all as specified and as directed.

Stainless steel grating of 125mm size (square/round), male/female pattern with or without hole, fixed in nahani/floor traps with white/coloured cement, fixed in repairs, complete all as specified and as directed.

PVC 32mm dia waste pipe with CP coupling, complete all as specified and as directed.

S&F in repair Bib taps, chromium plated cast copper alloy, with capstan head, screwed down for iron pipe or for brass ferrule and fixed for bore of pipe 15 mm, fixed in repairs, complete all as specified and as directed.

S & Fixed in repairs Angle stop valve cast copper alloy, with fancy type chromium plated capstan head, screwed down, high pressure screwed both ends for 15 mm bore iron pipe or for unions and fixed complete all as specified and as directed.4.

S&F in repair CP brass hot & cold 15mm dia wall mixture three in one (3 in 1) with provision for overhead shower with 115 mm long bend pipe on upper sie connecting legs & wall flanges for mixing hot & cold water complete all as specified and as directed.

S&F in repair CP brass hot & cold 15mm dia wall mixture with 2 way provision for kitchen & wall flanges for mixing hot & cold water complete all as specified and as directed.

S & F in repairs Chromium plated shower rose 125 mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and as directed.

S & F in repairs 20 mm dia Gun Metal, globe or Gate Valve with Iron wheel head Screwed both ends for Iron Pipe and fixed in repairs. complete all as specified and as directed.

Sheet glass shelf assembly consisting of 5,5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long make Jaguar or equivalent complete all as specified and as directed.

S&F 600x450mm PVC cabinet mirror of superior quality complete all as specified and as directed.

S & F Second class soft wood plain fillets square, rectangular or triangular in section, wrought secured with screws, cross sectional area exceeding 13 and not exceeding 25 Sq. cmcomplete all as specified and as directed.

18/19mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with screws to timber frame work as in cupboards , kitchen cabinat etc fixed in repairs complete all as specified and as directed.

S&F Continuous (piano) hinges,width of flap when open is 30 mm mild steel, bright finish or electrogalvanised complete all as specified and as directed.

S&F 100 mm long Extruded Aluminium alloy handles, fabricated type, anodised.complete all as specified and as directed.

S&F Magnetic catches of 25/30 mm size for cup Board shutter etc complete all as specified and as directed.

S&F hasp and stapple, safety typeof Aluminium, anodised, including bolt to hinge type, fixed with screws of 100 mm complete all as specified and as directed.

TMT steel bars 10mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping to columns, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and as directed.

TMT steel round bars 6 to 8mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping to columns, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and as directed.

Form work to soffit of suspended slab such as roof slab not exc 20 0 mm thick horizontal or slopinf flate including fair finished to concrete surfacescomplete all as specified and as directed.

Form work to Edges of concrete flate floor and roof n.exc 20 cm wide and similar work exc 10 cm but not exc 20 cm wide rough finished to concrete surfaces complete all as specified and as directed.

M&L RCC 1:2:4 Type B-1 (using 20 mm graded aggregate) in Roof slab, shelves supported on wall/column and the like etc complete all as specified and as directed.

M&L RCC 1:2:4 Type B-1 (using 20 mm graded aggregate) in landings, cover slabs (for man holes etc) and the like etc complete as required complete all as specified and as directed.

Demolition of Reinforced Cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Demolition of cement concrete in ground floors and paving (un reinforced) n exc. 15 cm. thickness, below or above ground level, complete all as specified and as directed.

M&L 75mm cement concrete type C-1 (1:3:6) using 20mm graded stone aggregate as in plinth protection complete all as specified and as directed.

S&F PVC (SWR) pipes single socketed in any length with rubbering joints fixed to walls 110mm bore complete all as specified and as directed.

S&F PVC (SWR) pipes single socketed in any length with rubbering joints fixed to walls 75 mm bore complete all as specified and as directed.

S&F PVC (SWR) bends any radius 110mm bore with access door complete all as specified and as directed.

PVC(SWR) junction single (single 'T') equal or unequal 110mm bore with access to door complete all as specified and as directed.

S&F PVC (SWR) bends any radius 75 mm bore with access door complete all as specified and as directed.

PVC(SWR) junction single (single 'T') equal or unequal 75 mm bore with access to door complete all as specified and as directed.

M & L for PVC (SWR) multi floor trap diameter of outlet 75 mm with grating including jointing with solvent cement complete all as specified and as directed.

S&F Plate rack made out of 1.00 mm thick stainless steel sheet of size 750mm x 750mm x250mm , complete all as specified and as directed.

Preparation of new wooden surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed.

Preparation of old steel surfaces of any description, over 10cm width or girth and applying one coats of synthetic enamel paint, complete all as specified and as directed.

M&L for two coats synthetic enamel paint over a coat of red oxide primer on newly steel surfaces complete all as specified and as directed.

Material and labour for preparation of newly plastered wall surface and applying two coat of premium acrylic smooth exterior emulsion of approved colour with silicon additive & Color stay Technology, Excellent Dirt Pick up resistance of Berger Paints Ltd or equivalent of other approved make with low VOC less than 50 gram/ litre as per the LEEDS specifications, Anti Algal properties in two coats @ 1.79 ltr (undiluted)/ 10 sqm diluted with water as per manufacturer instructions applied over one coat of acrylic water based exterior grade primer @ 0.9ltr(undiluted)/10 sq mtrs diluted with water in 1:1ratio as per manufacture's instruction and all coats incl primer to be applied with fully automatic airlessspray machine of paint application with a flow speed of minimum 1 ltr per minute having a pressure of 3300 PSI. Allow 6-8 hrs to dry the surface in subsequent coats of paint complete all as specified and directed Make: Berger Paints Weathercoat Long Life Flexo / Nerolac Paints excel Total / Asian Paint Apex Ultima Notes for smart periodicals item no 1 to 4 Note : (a) The work pertaining to periodical servcies & Water Proofibng shall be executed from authorized applicator through manufacturer of which the materials i.e Paint, Distemper, Cement base paint, putty etc is proposed to be used by the contractor and approved by Garrison Engineer. (b) The contractor shall upload along with the documents under cover-I, 'Memorandum of Understanding' (MOU) with only one manufacturer mentioned in the contract, failing which the bid shall be liable to be rejected.

Material and labour for complete removal of existing treatment including fascias, cornices etc by scrapping with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7"/9" to make the surface free from dust, loose paint and loose plaster to be completely removed by skilled labour and repair of external wall/Chajjas to be done with repair mortar to get even surface including preparation of old surface of wall/ceiling by filling cracks by Berger Bison Putty / crack fill paste of Berger Paints or equivalent make and make good smoothen surface by sand paper and applying two coats of premium acrylic smooth exterior emulsion of approved colour with silicon additive & Color stay Technology ,Excellent Dirt Pick up resistance of Berger Paints Ltd or equivalent of other approved make with low VOC less than 50 gram/ litre as per the LEEDS specifications, Anti Algal properties in two coats @ 1.79 ltr (undiluted)/ 10 sqm diluted with water as per manufacturer instructions applied over one coat of acrylic water based exterior grade primer @ 0.9ltr(undiluted)/10 sq mtrs diluted with water in 1:1ratio as per manufacture's instruction and all coats incl primer to be applied with fully automatic airless spray machine of paint application with a flow speed of minimum 1 ltr per minute having a pressure of 3300 PSI all as specified and directed. Allow 6-8 hrs to dry the surface in subsequent coats of paint and including necessary scaffolding at any height complete all as specified and directed Make: Berger Paints Weathercoat Long Life Flexo / Nerolac Paints excel Total / Asian Paint Apex Ultima Note : (a) The work pertaining to periodical servcies & Water Proofibng shall be executed from authorized applicator through manufacturer of which the materials i.e Paint, Distemper, Cement base paint, putty etc is proposed to be used by the contractor and approved by Garrison Engineer. (b) The contractor shall upload along with the documents under cover-I, 'Memorandum of Understanding' (MOU) with only one manufacturer mentioned in the contract, failing which the bid shall be liable to be rejected.

Complete removal of existing treatment from internal wall/ceiling surfaes including preparation of old surfaces and applying two coat of oil bound distemper complete all as specified and as directed.

Preparation of new plastered surfaces and applying two coats of destempering wall/ceiling with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/liters, of approved manufacturer of required shade and colour complete as per manufacturers complete all as specified and as directed.

Demolition of brick work or stone masonary built in cement mortar including all quoins , arches, pillar etc but excluding ashlars facing dressed stone work and pre-cast concrete article complete all as specified and directed.

M&L Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6, complete, all as specified and as directed.

Brick work with sub class ‘B’ bricks ,straight or curved on plan exc 6 m mean radius and built in cement mortar 1:6 complete , but except bricks , i.e using serviceable bricks obtained from demolition complete all as specified and as directed.

Brick work in cement mortar 1: 4, using sub class ‘B’ bricks, straight or curved on plan any radius in half brick thick wall complete all as specified and as directed.

M&L 100mm thick PCC 1:3:6 (Nominal mix) type C-2 using 40mm graded crushed stone aggregate as in sub base of floor complete all as specified and as directed.

M&L precast designer coloured heavy duty full body paving tiles (factory made) of size 300mm x300mm x10mm, top layer glazed made in any type of cement and pigment, in required pattern in floor etc, set and jointed in neat cement slury and pointed in white or coloured cement mixed with pigment to match over and including 15mm thick screed layer in cement mortar 1:6 complete all as specified and as directed.

M&L for glass fibre reinforced modified cementitious coating system before the final coat of Latex Shield 2K (or equivalent). Base coat: Berger HS Latex plus (or equivalent) both on walls ( upto 1.00 mtr min hieght ) and floor. Consumption base coat: 0.3 kg/m2 Reinforcement: Glass fiber Second and Third coat: Latex sheild 2K (or equivalent)both on walls ( upto 1.00 mtr min hieght ) and floor. Consumption top coat: 3 kg/m2 System requirements: density: 2.00 kg/ltr; compressive strength: 0.5 N/mm2. • Wall penetration through the RCC slab must be sealed using Berger HS RepirO(or equivalent). • Intersection of base slab with wall must be provided with a 50 mm fillet using Berger HS Latex plus(or equivalent) modified mortar with a bonding coat of Berger HS Latexplus(or equivalent) modified cement slurry upto 5ft. • All depressions, unevenness, surface honeycombing shall be repaired using Berger HS Latex plus(or equivalent) modified polymer mortar with a bonding coat of Berger HS latex plus(or equivalent)modified cement slurry. Including cleaning of RCC surface to remove dust, loose particles, etc with compressed air or any other suitable technique depending on site conditions, grinding any sharp edges, etc

S&F 20mm dia High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 laid in as spout pipes to pour out rsidual water out from the treated area complete all as specified and as directed.

M&L for hard core, of broken bricks broken to gauge n exc 63mm for laying sub base of thickness 150mm complete all as specified and as directed.

M&L Cement concrete type D-2 1:4:8 (40mm graded crushed stone aggregate) in foundations, filling and mass concrete in sub base complete all as specified and as directed.

M&L for 25mm thick PCC (1:2:4) type B1 with 20mm graded aggregate for laying floor tiles complete all as specified and as directed.

M&L Rendering 10 mm thick on fair faces of brick/concrete surfaces in cement plaster 1:4, using water proofing compound mix as per manufacturer detail, finished even and smooth without using extra cement, complete all as specified and as directed. (WPC measured and paid seperately)

M&L for non skid coloured Ceramic tiles 8 to 10 mm thick in light shade (square/ rectangular) polished, area of each tiles exc 0.11 sqm but not exceeding 0.18 sqm, in floors/Skirting etc. set, jointed and pointed with Berger HS tile adhesive anti slip white @1.2kg/sqm thickness upto 8 to 10mm (or equivalent) and epoxy material for sealing of tile joints with Berger HS Epoxy tile grout(or equivalent) to the floor of toilets and bathroom complete all as specified and as directed.

Demolition of cement concrete in ground floors and paving (un reinforced) n exc. 15 cm. thickness, below or above ground level, complete all as specified and as directed.

Complete removal of existing roof treatment or roof tile and removing from site to a place outside defence land as specified by civil authorities and clean the surface of roof with water and remove dust complete all as specified and as directed.

Cleaning of the exposed concrete slab and repairing the surface irregularities like cracks, potholes, as per manufacturers method statement by Berger HS Rapairo(or equivalent)along with HS Latex Plus(or equivalent)& cement in mixing ratio of 1:4 where ever required complete all as specified and as directed.

M&L for HomeSheild PU Roofkoat(or equivalent)is a one component liquid ,solvent free ,cold applied , water-proofing membrane that is highly elastic and UV resistant with 10 years Warranty .ASTM D 6083-97a Waterproofing and heat reflecting system having following key performance properties: 1.UV resistant ,prevent yellowing and weathering 2.Highly elastic upto 350% and crack bridging 3.Excellent adhesion on porous and non-porous substrates 4. Tensile Strength >10 N/mm2 with GeoTextile fleece 5. Soler Reflective Index (SRI) more then 109-111 ASTM E1980-11 System: First coat:Providing and applying primer over the prepared surface with HS PU roofkoat Primer(or equivalent) Coverage: 0.2kg/m2(with 50% dilution of water) Reinforcement: Geotextile 40 gsm Second coat:Home sheildroofkoat(or equivalent) Consumption: 0.5 kg/m2. Third coat: HS PU roofkoat(or equivalent) Consumption : 0.8 kg/m2. System buildup-1.5kg/sqm with geotextile of 40gsm For accessible roof, tiles with screed/ adhesive may be fixed thereafter.

Providing cement concrete type B-0 1:2:4 (using 12.5 mm graded stone aggregate ) in roof padding, roof kerbs or mud stops, rounded or chamfered on edges finished even and smooth without using extra cement complete all as specified and as directed.

Taking out carefully copper/aluminium point wiring,Light,fan,socket or power complete with all fitting, fixtures such as switch socket out let, ceiling rose ,holder ,regulator,DBs etc including making good the disturbed surface of wall/floors complete all as specified and as directed.

Taking down distribution boards/wooden board ,switch fuse units,steel enclosures for MCB of any type and removing from site complete all as specified and as directed.

Taking down existing unserviceable submain wiring any size and making good the disturbed surface complete all as specified and as directed.

Taking down electric energy meter single phase any size or type form the existing site and refixing the same at same place after carrying out necessary repair work in building and making the surface good to match with existing surface complete all as specified and as directed.

Taking down Geyser any cap/ type including disconnection electrically and refixing at same or new location with and including 2 Nos PVC connection for inlet/out let pipe ,thermostate,& indicator lamp as required at site.as complete all as specified and as directed.

Taking down ceiling fan/Ext fan any type including disconnection electrically complete all as specified and as directed.

Material and labour for point wiring for one light controlled by one way switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable 1100 Volts grade drawn through and including rigid non metallic PVC concealed conduit (medium grade) of suitable dia along with 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, connected to earth dolly and to be terminated in and including pressed steel sunken boxes , readily available (Having wall thickness not less than 1.22 mm for boxes upto a size of 200 mmX300 mm and beyond that the wall thickness shall be not less than 1.63 mm) concealed type with 3mm thick bakelite sheet cover for mounting switches, sockets, fan regulators etc including testing on completion complete including cutting chases for concealed conduit pinning in making good to facing and pointing in using cement mortar 1:3 and making good disturbed surface complete all as specified and as directed.

All as per item no 120 above but for one fan point controled by one piano switch all as specified and as directed.

All as per item no- 120 above but for one bell point controled by one bell push all as specified and as directed.

All as per item No 120 above but One light point controlled by two way switch complete all as specified and as directed.

All as per ser item No 120 hereinbefore but for one 3 pin socket outlet 5 Amp Same complete all as specified and as directed.

All as per ser item No 120 hereinbefore but for one 3 pin socket outlet 5 Amp independent complete all as specified and as directed.

All as per Item no 120 here-in-before but for one15 Amp 3pin switch socket outlet, independent with 2 Sqmm single core multi-stranded copper conductor cable (FRLS) along with 2.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire complete all as specified and as directed.

Supply and fix in replacement of Switch piano flush type single pole, two way 5 Amp , complete all as specified and as directed.

Supply and fix in replacement of Switch piano flush type single pole, one way 5 Amp , complete all as specified and as directed.

Supply and fix in replacement of Switch socket out let combination universal type, 2 in 1, 2 and 3 pin 5 Amp, piano flush type, 240 volts, complete all as specified and as directed.

Supply and fix in replacement of Switch socket outlet combination universal type, 2 in 1, 3 pin 5 and 15 Amp, piano flush type, 240 volts, complete all as specified and as directed.

Supply and fix in replacement of Ceiling rose surface bakelite three terminals 240 volts complete all as specified and as directed.

Supply and fix in replacement Lamp holder PVC case body of Bakelite with back plate suitable for batten fittings , complete all as specified and as directed.

Supply and fix in repair LED lamp,6500K,900lm in white colour of 12 Watt base cap B-22 with poly carbonate difusser and aluminium heat sink , complete all as specified and as directed.

Electronic fan regulator stepped type,two module with five step 240 volts,100Watt suitable for 1200/1400 mm sweep AC ceiling fan complete all as specified and as directed.

Supply and fix in replacement of Bell push flush type piano 5 Amp complete all as specified and as directed.

Supply and fix in replacement Bell multi music 230 volt ,AC single pole complete all as specified and as directed.

Supply and fix in replacement of Tube light fitting integrated type suitable for LED 10W indoor decorative aluminium extruded T5 LED batten complete with hosing with all accessories pre wired and making connection with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connection to light fitting complete all as specified and as directed.

Supply and fix in replacement of Tube light fitting integrated type suitable for LED 20W indoor decorative aluminium extruded T5 LED batten complete with hosing with all accessories pre wired and making connection with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connection to light fitting complete all as specified and as directed.

Repair and Fixing Exhaust Fan any type 300mm(12") sweep, single phase, 230 volts 50 Hz AC, connecting electrically using 3 core 0.75 Sq mm PVC insulated flexible copper conductor cable over all sheathed including oiling and greasing all as required at site complete all as specified and as directed.

Repair and Fixing ceiling fans complete with blades, and accessories obtained vide srl Item No-3 above with provision of new Anti suicide Fan Rod (suitable size and length and oiling/greasing of fan with provision of flexiable cable twin core all as reqd at site. complete all as specified and as directed.

Supply and fix in repairs factory made epoxy powder coated Distribution board VTPN 6 ways ,415 Volts with metal door (IP-54 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 100 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cale management, top and bottom removable gland plates with Knockouts and suitable for one MCCB as incommer and SP MCBs outgoing complete all as specified and as directed.

Supply and fix in repairs factory made epoxy powder coated Distribution board SPN 12 ways (SPN MCB DB) with metal door (IP-54 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 100 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cale management, top and bottom removable gland plates with Knockouts and suitable for one SPN/DP-MCB as incomer and SP MCBs outgoing complete all as specified and as directed.

Supply and fix in replacement of Thermal magnetic release MCCB 3 pole 415 volt rapturing capacity 36 KA 0f size 160 amp complete all as specified and as directed.

Supply and fix in replacement of Sheet metal enclosure IP-43 double door for DBs(where MCBs are reqd) SPN 240 V, for 12 ways, complete all as specified and as directed.

Supply and fix in replacement of MCB SP 10KA, 'B' curve, 06 to 32 Amp, 240 volts complete all as specified and as directed.

Supply and fix in replacement of MCB SPN -10K, 'C' curve, 6-32 Amp, 240 volts 50Hz AC supply, complete all as specified and as directed.

Material and labour for sub main wiring with two single core PVC insulated (unsheathed) multi strand copper conductor FRLS cable of size 6 sqmm and one single core PVC insulated (unsheathed) solid copper conductor FRLS cable of size 6 sqmm as in continuous earth wire drawn into and including concealed PVC conduit medium grade 25mm dia ISI marked complete with fittings and fixings accessories complete and including cutting chases pinning in making good to facing and pointing in using cement moter 1:3 and making good disturbed surface complete all as specified and as directed.

Earthing complete with galvanized mild steel earth plate electrode size 600x600x6mm thick buried directly in ground (Preferably in vertical position) earth pit not less than 2.25 meter below normal ground level with top edge of the earth plate not less 1.5 meter (BGL) connected to galvanized iron earth lead wire 4mm dia by means of bolts, nuts, check nut and washer of galvanized iron including PCC pit in RCC 1:2:4 type B-1, precast RCC cover with suitable handle, excavation and earth work in any type of soil, 20mm bore “medium grade” galvanized iron water tubing fixed with cast iron funnel and wire mesh and 15mm bore “light grade” galvanized iron protection pipe for earth lead wire upto 5m length, charcoal, common salt, complete all as shown in EP No 3 of SSR 2009 part-I, connected to test point complete, all as specified and testing on completion. complete all as specified and as directed.

Supply and fix IP 66 Integral LED security light luminaire 60W LED 230 volts made of pressure die cast aluminium housing with high power LED’s lens & heat resistant toughned glass ,efficacy 110 lumens/watt, external 10KV,440 volt SPD and inbuilt 4KV , IP 67 potted isolated driver with operating range 902V to 340V AC .CCT 5700K,LED life -1 lakh burning hours,fixture should withstand 320 volt upto 48 hrs , Auto cut off >320 volts & restart,440 Volt sustain upto 8 hrs,NABL Acreddited LM79 report including GI pipe 40mm ,medium grade ,1.7mtr long mounting bracket and providing fixing clamps ,bolts,nuts of suitable size complete all as specified and as directed.

M&L for single pole and neutral encloser with a two pin and earth plug and socket coplete with one single pole mcb 20 amps. complete all as specified and as directed.

Cutting existing steel tubing 15 mm bore for alterations or additions (Each cut measured) complete all as specified and as directed.

Screwing existing steel tubing 15mm for alterations or additions. complete all as specified and as directed.

S & F Tubes medium grade galvanized 15 mm dia with fittings such as socket, bend and fixed complete to walls and ceilings complete all as specified and as directed.

S&F Stop valve/angle valve cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe of four unions and fixed complete of size 15mm bore complete all as specified and as directed..

S&F Bib tap 15mm chromium plated cast copper alloy with crutch or butterfly screwed down for iron pipe and fixed complete. complete all as specified and as directed.

Dismentaling and taking out rusted/corroded pipe GI/CPVC of sizes 20/25/40/50mm bore complete all as specified and as directed.

M & L for replacement of tubing GI "MG" with all fittings laid in floor or trenches including taking out old UNSV pipe of size 50 mm dia complete all as specified and as directed.

M & L for replacement of tubing GI "MG" with all fittings laid in floor or trenches including taking out old UNSV pipe of size 25 mm dia complete all as specified and directed

M & L for replacement of gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of size 50 mm bore complete all as specified and as directed.

M & L for replacement of gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of size 25 mm bore complete all as specified and as directed.

Cutting existing 80/100/150 mm GI pipe and inserting GI Tee of size 100x100x50 mm for tapping including necessary earth work and making flange for connection of new 50 mm of GI pipe including complete all as specified and as directed.

Dismantling of old U/S valve pit of size 400x400x400 mm ( internal dimensions of the chamber) including and removing the debris at a distance not exceeding 50 Mtr and M/L for brick massonary with cement mortar with 1: 6 , 23 cm and flush pointing externaly work proceeds in the same mortar complete ( using 30% old bricks & 70% New bricks) complete with the following specifications complete all as specified and as directed. Note :-(i) 10mm thick plaster internally in CM 1:6.(ii) Flooring 40mm thick in PCC 1:2:4 type B-1 over 75mm thick hard core of guage not exc 63mm thick. (iii) Angle iron frame 40X40X6mm thick for cover and mild steel 3.15mm thick cover with locking arrangement,handle and necessary hinges etc, (iv) PCC 1:3:6 type C-2 100mm thick in foundation .(v) Two coat of synthetic enamelled paint to cover internally and externally over a paint of Red Oxide primer.

Excavation in trenches, n. exc1.5 m wide and n. exc 1.5 m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc. 10 sq m on plan and n. exc1.5 m in depth and getting out in soft / loose soil complete all as specified and as directed. Note : All excavation for taking out and re-laying of cables shall be carried out mannualy and paid under this relevent item.

Removing Excavated soils not exceeding 50 M and depositing where directed at a level not exceeding 1.5m above from the starting point complete all as specified and as directed.

Dismentaling and taking down un servuceable /damaged LT UG cable of sizes from trencheh /flooor etc complete all as specified and as directed.

Material and labour for cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armored, electric power cables (heavy duty 1100 Volts grade with stranded aluminium conductor of size 50 Sqmm 3.5 Core, including glands, lugs, nut, bolts, washers as required at site, testing complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 metres wide and not exceeding1.5 metres in depth and getting out in any type of soil complete all as specified and as directed.

Returning, filling in, including spreading , leveling , watering and well ramming in layer not exceeding 25cm each layer complete all as specified and as directed.

Removing excavated material not exceeding 50M and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed.

Sand cushioning to underground cables provided with a layer of sand 8cm thick before laying the cable in trenches and 15cm thick after laying the cable in trenches complete all as specified and as directed.

S & F Steel pipe glavanized light grade of 40 mm core laid in trenches or under ground/floor or road of fixed with pole for protection of cable including clams with bolts nuts and wasers complete all as specified and as directed.

Sub class ‘B’bricks for covering to cable laid dry flat ,with width equal to the length of brick. complete all as specified and as directed.

Hare krishna engineering const. (BID ID -3406480)

RAJINDRA ENGINEERS & CONTRACTORS (BID ID -3413868)

M/s Khajuria Construction Co. (BID ID -3409280)

M/s Anand Prakash (BID ID -3416495)

M/S VED PAUL MAHAJAN (BID ID -3414774)

M/S ARUN ANAND (BID ID -3409226)