Loading…
India Infra Updates on WhatsApp
Join the Tenderkart WhatsApp channel for India Tender Updates
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹3.7 LAccepted-AOC BHAGWATI NAGAR JAMMU | L1 | Accepted-AOC L1 | |
| 2 | L2₹3.9 L+₹16,500 (4.46%)Rejected-AOC | L2 | Rejected-AOC L2 | |
| 3 | L3₹4.0 L+₹27,900 (7.54%)Rejected-AOC BYPASS NH NEAR SBI SIDHRA JAMMU | L3 | Rejected-AOC L3 | |
| 4 | Rejected-Technical MAIN ROAD SIDHRA JAMMU | - | Rejected-Technical Non submission of necessary documents required as per SBD |
Tender Value
Refer Docs
EMD Value
₹8,000
Closing Date
19 Sept 2023, 1:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Executive Engineer Mechanical Division RTIC Kathua
Executive Engineer Mechanical Division RTIC Kathua
Replacement/ Rebuilding of guide/thrust/journal pads of 1500 HP HT induction motor (BHEL Make ) of unit no.01 along with allied works installed at LIS Basantpur
2023_IFC_227998_1
e-NIT No.17 of 2023-24 dt. 29.08.2023
Open Tender
Electrical and Maintenance Works
Turn-key
30 days
Basantpur
Please refer Tender documents.
2 documents required · 2 mandatory
₹500
Yes
Executive Engineer Mechanical Division RTIC Kathua
₹8,000
Yes
Executive Engineer Mechanical Division RTIC Kathua
19 Oct 2023
29 Aug 2023
20 Sept 2023
29 Aug 2023
19 Sept 2023
6 Sept 2023
5 Sept 2023
Amount
Replacement/Rebuilding of damaged guide/thrust/journal pads (acting as bearings) of 1500 HP vertical solid shaft, slip ring, tilting pad type HT motor of pumping unit installed at lift irrigation station Basantpur. The job involves fabrication & providing of new thrust pads (Bearings)-10 No`s in place of old damaged/broken pads. Repair /rebuilding of damaged pads by way of removing old white metal from the damaged 10 no’s guide/journal pads (bearings) by way of heating them to the required temperature using compressed air for the operation, cleaning the surface of pads (bearings) by acid treatment using required acid after cleaning and finishing the surface of guide/journal pads (bearings) properly. Providing primary coating of tin for filling up the gaps on the pads(bearings) surface, providing and applying 5 mm thick white metal (Babbitt) of superior quality on unfinished 10 no’s guide/journal pads (bearings), finishing the pads on the fabricated pad holder for making final size by way of surface grinding in circular motion for getting the correct size of required diameter as per site conditions for 10 no’s guide/journal pads (bearings). Extraction of damaged sleeve with heat treatment so as to rectify the fault of leakage of oil from oil chamber. Providing and fitting of new sleeve as per sample & size. Cleaning the complete stator & rotor by removing the dirt deposits from stator & rotor by cleaning them thoroughly by using high pressure blower & then with CRC-226 compound thoroughly and varnishing with superior quality varnish by using air pump gun. Assembling of all the dismantled components of motor such as rotor, stator, top cover & bottom cover with fitment & adjustment of top, centre & bottom pads (Bearings) in their respective bearing housing with replacement of damaged worn out nuts/bolts, oil seal, pipe nipple, etc & testing the alignment of rotor . Providing & filling of servo grade-46 oil 35litres approximately into the oil chambers for topping up. The job further involves repair to slip ring assembly by extraction of damaged/worn-out carbon brushes, brush holders etc. Repair to slip rings by way of cleaning, brushing and removing the carbon deposits & pits with the help of wire brush and sand paper then providing and fitting of new carbon brushes -24 no’s, brush holders-14 no’s. Taking IR value after drying out varnish by making temporary temperature drying up process and is to be continued till required IR value is achieved. The job also involves Re-installation of motor on motor stool and coupling it with V.T pump, making of water lubrication connections, electrical connections and testing of the pumping unit on no load and then on full load. The job also involves painting of motor and motor stool by way of removing all dust deposit, cleaning of surface and then applying metal primer as per requirement and there after two coats of superior quality paint. The job includes the cost of material, skilled/unskilled labour charges, hire charges of tools and tackles required for execution of work at site and too and fro carriage charges etc. Complete job.
M/S RAGHUNATH MECHANICAL AND ELECTRICAL ENGINEERING WORKS
G S ENGINEERING WORKS
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .