CWE/PAT/T-46/2019-20 SPECIAL REPAIR TO CERTAIN BUILDINGS UNDER

Amount

Schedule 'A'Section-I (Building Works)

Total amount of Sch 'A' Sec I (Building Works)

Schedule 'A'Section-II (INTERNAL ELECTRIFICATION WORKS)

Total amount of Sch 'A' Sec II (Internal Electrification Works)

Schedule 'A'Section-III (Misc Items of Works) Note : This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under Col. 5 siginifies this fact only.

Supply only chicken wire mesh 22 gauge of size not more than 20X20mm all as specified & as directed by Engineer-in-Charge.

Supply only integral liquid water proofing compound all as specified & as directed by Engineer-in-Charge.

Complete removal of existing treatment of any type/description from walls/RCC surfaces etc with mechanical means/grinder complete all as specified and directed.

Applying 02 coats of interior emulsion paint (light shade) @ 10 sq.m/litre/2 coats by using roller/brush to wall surfaces over & including a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer complete all as specified and directed. Make of Interior Wall Primer : Asian / Berger / Nerolac [Best Quality]. Make of Interior Emulsion : Asian ( TRACTOR) / Berger (BISON) / Nerolac (BEAUTY SMOOTH).

Applying 02 coats of interior emulsion paint (white shade) @ 10 sq.m/litre/2 coats to ceiling surfaces over & including a coat of interior primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer complete all as specified and directed. Make of Interior Wall Primer : Asian / Berger / Nerolac [Best Quality]. Make of Interior Emulsion : Asian ( TRACTOR) / Berger (BISON) / Nerolac (BEAUTY SMOOTH).

Applying 02 coats of exterior emulsion paint (light shade) @ 5 sq.m/litre/2 coats by using roller/brush to external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer @ 11 sq.m/litre/1 coat as recommended for under coat by manufacturer of exterior emulsion by using following brands of emulsion and primer complete all as specified and directed. Make of Exterior Wall Primer : Asian / Berger / Nerolac [Best Quality]. Make of Exterior Emulsion : Asian ( ACE) / Berger (WALMASTA) / Nerolac (SURAKSHA SUPERIOR).

S&F factory made ISI marked flush door shutters 35mm thick, BWP conforming to IS : 2202 (Part-I) non decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 Ply veneering with vertical grains or cross bands and face veneers on both faces of shutters complete all as specified and including supply and fixing following items : (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 4 Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16 x 300mm - 1 No per leaf (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 No per leaf

S&F 35mm thick glazed and skelton shutters of 2nd class hard wood (factory made) open rebated and divided to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR-91 Pt-1 section 8 clause 8.20(a), kiln seasoned and chemically pressure treated all as specified including stainless steel 304 Grade wire cloth (0.36mm nominal dia of wire and average width of aperture 1.40mm) and the supply and fixing following items: (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 4 Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16x300mm - 1 No per leaf

S&F powder coated 50 microns extruded aluminium glazing/ doors & shutters made out of section 63.5x38.10x1.29mm for chowkats or frame & shutters made of size 44.45x44.45x1.29mm for side rails and middle rail, 114.3X44.45X1.29mm for top rails and bottom rails and including 12mm thick PVC celuka Board wooden finish pre-laminated on one side and plain on other side below & above middle/lock rail and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beads 20mm size with and complete all as specified and directed including supply and fixing the following items: (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 3 nos per leaf. (b) Powder Coated Aluminium Tower Bolt 200mm long - 2 nos per leaf (c) Powder Coated Aluminium Handles 150 mm - 2 nos per leaf

Providing and fixing factory made extruded aluminium casement windows with 50 micron powder coating with provision for desert cooler, doubled panelled and double shutters consisting of frame and mullion of 101.60 X 44.45 X 1.29 mm and shutters made of 63.5 X 31.75 X 1.29mm and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and including 5mm thick glass in front shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperature in inner shutters complete fixed in all respect as specified including supply and fixing following items :- (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 2 Nos per leaf. (b) Powder Coated Aluminium Tower Bolt 150mm long - 2 Nos per leaf. (c) Powder Coated Aluminium Handles 150 mm - 1 Nos per leaf.

Providing and fixing aluminium sliding windows with 50 micron powder coating, three track sliding windows with two glazed shutters, 5mm thick tinted glass ordinary quality and one shutter of stainless steel wire mesh 0.36mm nominal dia of wire and average width of aperture 1.40mm including good quality of bearing handle, locks, including EPDM gasket to render the glazing, air and water tight etc complete all as specified and as directed . Section of Jindal Company : Three track bottom - 20957, Three track top / vertical - 20958, handle - 20606, Interlocking - 20605, Top and Bottom - 20604. Make (Aluminium Section) : Jindal / Valco / Galco / Hindalco or equivalent as approved by Accepting Officer.

Providing and fixing factory made extruded aluminium ventilators with 50 micron powder coating of frame of 63.5 X 38.10 X 1.29 mm including 5mm thick frosted glass in lower 55% portion of shutters and stainless steel wire gauge 0.36mm nominal dia of wire and average width of aperture 1.40mm in upper 45% portion of shutter and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and complete fixed in all respect as specified.

S&F factory made aluminium 50 micron powder coated grill, opening size 101.6 X 63.5 mm (4"X2½") and of approx weight @ 1.345 Kg/sq.m complete fixed in position in windows in all respect as specified

S&F stainless steel tubing of 25 mm dia chromium plated 1 mm wall thickness as in curtain rod complete incl S&F 02 Nos stainless steel brackets fency type, stops etc all as specified & directed as in repair . Note : For the purpose of mesurement and payment running length of curtain rod only shall be considered.

M&L for single charge, stainfree, vitrified tiles, Premium (1st) quality straight edge, coloured tiles 600 X 600 mm and 9-10 mm thick, as in floors etc. in any pattern of coloured tiles as approved, over & incl. set and jointed 20 mm thick screed in cement mortar (1:4) and pointed in white or coloured cement to match, in floors etc. and pointed in white cement with pigment to match the colour of tiles complete all as specified.

M&L for single charge, stainfree, vitrified tiles, Premium (1st) quality straight edge, coloured tiles 600 X 100 mm and 9-10 mm thick in any pattern of light coloured tiles as approved, on vertical surfaces such as in skirting/dado etc, height not more than 150mm, set and jointed over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified.

Providing and Laying Premium (1st) quality straight edge, ceramic tiles of size 300x300x7 to 8 mm thick in floors etc. in any shade and design/pattern of light & dark tiles etc as approved matching with wall tiles, set & jointed in neat cement slurry & incl and over 20 mm thick screed in cement mortar (1:4) pointed in matching colored polymer cement based grout to match complete all as specified and directed.

M&L for anti-skid Premium (1st) quality colour tiles 400 x 400 mm and 7-8 mm thick, as in floor etc. in any pattern of light and dark tiles as approved, set and jointed in neat cement slurry and pointed in white or coloured cement to match, in floors etc.over and including 20mm thick screed in cement mortar (1 :4) over pointed in white cement with pigment to match the colour of tiles complete all as specified.

M&L for Baroda Green marble, machine cut as in shelves/steps/cills/jambs/skirting/border only in tile flooring and the like works and flooring etc, 15-16 mm thick including bull-nose the exposed sides/lengths, set and jointed in cement slurry over & including screed of 15 mm thick rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab for fixing on concrete surfaces or with suitable adhesive for fixing on un-polished kota stone slabs including rubbing, cutting and mirror type granite polishing and including dismantling/demolition complete all as specified. Note : Single piece should be used in steps/cills/jambs/shelves.

S&F vitreous china premium/1st quality wall hung wash basin white, flat back, size 500x400 mm screws & plug and brackets etc. all accessories as recommended by manufacturer incl. CP bottle trap 32 mm with inlet and outlet screwed for pipe or connections incl all necessary accessories for fixing, packing, union and incl 32mm brass CP waste coupling half thread and complete in all respect as per manufacturer's instructions and taking down existing of any description/size all as specified.

S&F vitreous china premium/1st quality wash down water closet Pan (Pedestal pattern / EWC) S/P trap white colour of size 520 x 360 x 390mm including connection to drain (or out going pipe) and to flushing pipe, antisyphonagee pipe, etc., with flush pipe 32mm dia and incl. plastic seat cover as recommended by manufacturer closed pattern with flat bottom etc; and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing, packing including taking down existing of any description/size complete in all respect all as specified. Make : Cera (Conventional) / Hindware (Slick) / Equivalent from Parryware.

S&F flushing cistern of PVC 10 ltr. cap. with dual flushing system, white colour, valveless syphonic action type, , low level, with inlet, ball valve, float and including brackets and connection to pipe etc. and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing, packing and taking down existing of any description/size complete in all respect all as specified. Make : Hindware (Sleek Essence Dual Flush) / Cera (Corona) / Prayag (Vintage).

S&F PTMT Jet Spray with 1.5 metre long flexible tube including making connections and fixed in position complete in all respect as specified. Make PRAYAG / POLYTUFF / SHAKTI

S&F 6mm thick looking mirror beveled edge fixed to wall with stainless steel plugs/connecter/spacers/screws etc. chrome finish, etc.complete fixed in position all as specified and directed.

S&F sheet glass shelf assembly consisting of 8mm thick glass shelf 300 x 300mm as in corners wide with bevelled edges/hatching of edges fixed with stainless steel 'D' bracket fixed and railing complete all as specified and directed.

S&F PTMT 450 mm long shelf for wash basin , fixed in position complete all as specified.

S&F overhead shower 120mm dia with 225-230mm long brass shower arm with wall flange and incl all necessary accessories as recommended by manufacturer for fixing complete in all respect all as specified. Make : Cera / Hindware / Jaquar.

S&F Bib taps, CP, fency type long nose with wall flange screwed for 15mm bore of iron pipe or for brass ferrule and fixed in position complete in all respect all as specified. Make : Jaquar (Continental Series) / Hindware (Contessa Plus Series) / Cera (Ocean Series) / Prayag ( Neptune Series)

S&F central hole brass chromium plated basin mixer with regular spout with/without popup waste system with 450 mm long braided hoses complete. Make : Jaquar (Continental Series) / Hindware (Contessa Plus Series) / Cera (Ocean Series) / Prayag ( Neptune Series)

M&L for wall mounted mixer assembly, brass chromium plated, comprising of centre outlet tap, double inlets for hot & cold water, with connecting legs & wall flanges, inlets suitable for 15mm bore connections complete all as specified and directed. Make : Jaquar (Continental Series) / Hindware (Contessa Plus Series) / Cera (Ocean Series) / Prayag ( Neptune Series)

S&F Concealed Stop Cock, fancy type, CP with long shank and cup, exposed part kit with wall flange, fitting sleeve, operating lever, adjustable wall flange and including regular brass body of concealed stop cock suitable for 15mm line with protection cap fixed in position complete in all respect all as specified. Make : Jaquar (Continental Series) / Hindware (Contessa Plus Series) / Cera (Ocean Series) / Prayag ( Neptune Series)

S&F Angular Stop Cock, CP, fency type with wall flange, fency type chromium plated cast copper alloy screwed down, high pressure, screwed ends for 15mm bore of iron pipe or for union and fixed in position complete in all respect all as specified. Make : Jaquar (Continental Series) / Hindware (Contessa Plus Series) / Cera (Ocean Series) / Prayag ( Neptune Series)

S&F stainless steel sink with drainage board, AISI 304 quality grade, 1.00 mm thick, glossy finish, for kitchen with plugs washers and CP waste coupling/round strainer of 110mm dia and including cantilever cast iron brackets, connecting union, etc, overall size 914mm x460x203mm with bowl size 405x 354x203 and making good disturbed portion in CM 1:3 or PCC 1:2:4 as directed. Make : Prayag / Neelkanth / Nirali / Diamond

Demolition of reinforced cement concrete of any description and in water storage tank of any size/capacity/description/position located on terrace of the building including moving the demolition portion to low lying area or out of defence land all as specified and directed.

Disconnecting existing water tanks of 300 to 500 ltrs capacity, setting aside (or lowering if required) for repairing, cleaning, etc. and hoisting, reconnecting and incl S&F PVC water tank cover & 20mm dia brass float valve, changing of chuk nuts, socket and re-fixing in position after cleaning the water tank complete all as specified and directed.

Repair to RCC ceiling, sunshades, Chajjas, Balconies, Columns, bands, beams, roof slab and similar RCC work at any position/height by dismantling loose/disintegrated portion and dubbing out with Cement Concrete 1:1½:3, 15mm to 50mm thick using 6 to 12mm graded stone aggregate to make up and finished to required shape including provision of necessary supports if required and stitching of cracks with mild steel U clamps made out of 8mm dia @ 150mm c/c with inserting concrete block stretcher with cement mortar 1:3 mixed with adhesive chemical (Polymer based) and reinforced with PVC chicken mesh including form work where ever required and finished with10 mm thick plastering in CM 1:4 finished even and fair without using extra cement including preparation of surfaces to receive finishes complete all as specified and directed. Note : The extra area of 300mm around the actual affected area will be checked and repaired and only repaired portion will be taken for measurement.

Applying three coats of brush bond acrylic based cementitious material of approved quality for sunken portion treatment all as per manufacturer instruction and providing 200 micron thick polythene film over 85/25 grade bitumen layer @ 0.5 kg /Sqm all as specified

S&F cast iron 'Y' junction for 100 mm bore with access door as in repair complete all as specified.

Providing and laying 3mm thick APP (Atactic Polyproplene Polymer) modified prefabricated five layer, weight not less than 4.0 Kg/Sqm water proofing membrane black finished, reinforced with non-woven polyster matt make as approved including of a coat of bitumen primer @ 0.40 ltr/sq.m by the same membrane manufacturer of density 0.87 to 0.89 Kg/Ltr at 25 degree C temperature and viscosity 70 - 160 cps Over the coat, 3mm th 5 layered APP membrane shall be laid using butane torch and sealling all joints etc after the surface complete as per standard practice as per manufacturers instructions. The vital physical and chemical parameters of the membrane shall be as under - (i) Joint strength in longitudinal and transverse direction at 23 degree C as 650/450N/5cms (ii) Tear strength in longitudinal and transverse direction as 300 / 250 N/. Softening point of membrane not less than 150 degree C Cold flexibility upto 20 degree C when tested in accordance with ASTM (D05147) (iii) The laying of membrane shall be got done through the authorised applicator of manufacturer of membrane only all as specified. Make : Sika / STP / Fosroc or equivalent as approved by Accepting Officer.

M&L for Dummy joints/construction joints 8mmx10mm as in PCC floors filled with polyurethane elastic adhesive/sealant (white/grey colour) of aprrox density 1.3 kg/litre complete all as specified.

Chipping of unsound weak concrete / cover of reinforcement over slab, column and walls as per site requirement by chieseling maximum upto 30mm depth and removal of rubbish off the premises complete all as directed by Engineer in Charge.

Supply and apply of rust remover cum passivator by brush in two coat @ 0.3 kg/m2/coat of Density: 1.01 Kg/l at 300C complete all as per manufacturer's instructions and all as specified. Note : 1. The application of rust removal shall be got done through the authorised applicator of manufacturer of membrane only all as specified and directed. 2. Rates of scaffolding is deemed to be included in the rates quoted by the contractor against each item.

Supply and apply Cementitious Coating for Corrosion Protection having a cement based polymer modified rebar corrosion protection system by appling the first coat approx. 1mm thick layer of product carbonation resistance 2 mm of SikaTop Armatec®-108 or equivalent as specified corresponds to 20 mm of normal mortar; bond strength > 1N/mm2 according to ASTM C 882-78 applying @ 4 kg/m2 for two coats onto the prepared reinforcing steel with a medium- stiff brush. It is unavoidable that Sspecified product will also be applied onto the surrounding concrete. The second coat is applied in the same way after a waiting time of 2-3 hours (at +20°C) complete all as per manufacturer's instructions and all as specified. Note : 1. The application of Cementitious Coating for Corrosion Protection shall be got done through the authorised applicator of manufacturer of membrane only all as specified and directed. 2. Rates of scaffolding is deemed to be included in the rates quoted by the contractor against each item. Make : Sika / STP / Fosroc or equivalent as approved by Accepting Officer

Providing, mixing & applying two component Epoxy resin concrete Bonding coat on prepared RCC surfaces as per manufacturer's specification including prepartaion of surface by chipping and throughly cleaning of surface complete whereever required and as per directions of Engineer-in-charge. Consumption: 0.5 kg/m2. complete all as per manufacturer's instructions and all as specified. Product requirements: Complies with ASTM C 881 Type II Grade 2 Class B+C. Note : 1. The application of Epoxy Bonding Primer shall be got done through the authorised applicator of manufacturer of membrane only all as specified and directed. 2. Rates of scaffolding is deemed to be included in the rates quoted by the contractor against each item. Make : Sika / STP / Fosroc.

Supply and apply a pre-batched one component polymer modified cementitious patch repair mortar in 25 mm thickness. Yield: approx. 0.84 ltr/kg. System requirements: compressive strength >= 50 N/mm2 (28 days) according to ASTM C 109; flexural strength >= 3N/ mm2 (7 days) according to ASTM C 293-79. Consumption of 2.1 Kg/Sqm/mm Note : The application of Polymer repair Mortar shall be got done through the authorised applicator of manufacturer of membrane only all as specified and directed. 2. Rates of scaffolding is deemed to be included in the rates quoted by the contractor against each item. Make : Sika / STP / Fosroc or equivalent as approved by Accepting Officer

S&F 18 mm thick with minimum density 600 Kg/cu.m LEAD FREE PVC Celuka ply of both side plain white color fixed with screws, solvent cement/ adhesive to make kitchen/bed rooms cabinet sides top and bottom and shelves inside the cabinets complete as per manufacturer’s specifications complete all as specified and directed. Make : Rajshri Plastiwood / M/s Kumar Arch (P) Ltd or equivalent as approved by Accepting Officer.

S&F 18 mm thick with minimum density 600 Kg/cu.m LEAD FREE PVC Celuka ply of single rigid laminated of approved colour and other side plain white colour fixed with screws and solvent cement/ adhesive to make kitchen cabinet shutters complete as per manufacturer’s specifications complete all as specified and directed. Make : Rajshri Plastiwood / M/s Kumar Arch (P) Ltd or equivalent as approved by Accepting Officer.

S&F 12 mm thick LEAD FREE PVC Celuka ply fixed with ss screws, solvent cement/ adhesive to make wall mount kitchen cabinet back and pull out drawers sides complete as per manufacturer’s specifications complete all as specified and directed.

S&F 5 mm thick with minimum density 600 Kg/cu.m LEAD FREE PVC ply of single rigid laminated of approved colour and other side plain white colour and pasted with screws and solvent cement/ adhesive on frame work of cup boards complete as per manufacturer’s specifications complete all as specified and directed. Make : Rajshri Plastiwood / M/s Kumar Arch (P) Ltd or equivalent as approved by Accepting Officer.

S&F 6 mm thick with minimum density 600 Kg/cu.m LEAD FREE PVC ply fixed withss screwed and solvent cement/ adhesive to make wall mount kitchen cabinet back and pull out drawer side complete as per manufacturer’s instructions complete all as specified and directed. Make : Rajshri Plastiwood / M/s Kumar Arch (P) Ltd or equivalent as approved by Accepting Officer.

S&F auto closing hinges 35 mm of 0 crank( KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete in all respect and fixed in position all as specified.

S&F Ball bearing runners 45 mm Telescopic (KTS-20) full extension load capacity 50 kgs.

S&F towel bolts 150mm long of stainless steel 304 finished/of outer plate metal matt finished complete all as specified and directed.

S&F D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 200mm long matt finished complete fixed in position all as specified.

S&F Piano / continuous Hinge of size 19 mm stainless steel complete all as specified and directed.

S&F ball catchers 304 grade stainless steel finished suitable for cabinets premium quality complete fixed in position as per manufacturer's instructions all as specified.

S&F D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 150mm long matt finished complete fixed in position all as specified.

S&F Stainless Steel 304 grade wire Basket (avg. wait 2.5 to 4 Kg. per basket) of pull out type like plain/cup&saucer/bottle/multi purpose/2-3 shelf baskets etc. for kitchens of required suze complete fixed in position all as specified.

S&F wardrobe tube/hanging rod for CB of size 30x15mm and 0.6mm thick stainless steel grade rectangular high gloss finish complete fixed in position incl S&F brackets/screws etc. all as per manufacturers instructions all as specified and directed.

S&F stainless steel finished locks (double action) with 2 nos of keys min outer body size 75mm suitable for wardrobe/CB etc complete all as specified.

M&L for Modular Socket 6A/16A - 2/3 pin 2 module type all as specified and directed. Make: Havells/cona/ssk/Polycab

M&L for Modular Socket, 6A - 5 pin 2 module type all as specified and directed.Make: Havells/cona/ssk/polycab

M&L for Modular switch 1 way 6A, 1 module Make:SSK/Cona/Havells/Polycab

S & F Modular switch 1 way, 16 Amps, 1 module complete all as specified.

M & L Modular bell push 1 way, 06 Amps, 1 module complete all as specified.

M&L fan step regulator modular type 1 module 120 W complete all as specified.

S&F in replacement of MCB SP upto 6-32 Amp all as specified and directed.

S&F in replacement of MCB SPN 6-32 Amp all as specified and directed.

Supply & fix in replacement of existing unserviceable FTL with new techonlgy self blasted LED retrofit tube lamp with thermoplastic body with high lumen 18 w 6500 K suited for installation in existing t5 tubelight including neccessary electric conection with box type batten.

S & F LED Lamp LED new Adore 7W E27 WW Ball Lamp 9 Watt all as per specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode 600x600x6mm tthick buried directly in ground(earth plate not less than 2.25 mtr deep below the normal ground level ) with top edge of plate not less than 1.5 mtr below the normal ground level connected to galvanized earth wire 4mm dia by means of nuts bolts,washers,check nuts of iron or steel including test point PCC pits and RCC cover in PCC 1:2:4 (type B-1) including iron angle frme 40*40*6mm. and medium grade GI watering pipe 20mm dia with funnel and wire mesh and 15 mm bore GI pipe light grade proection pipe including excavation and charcoal ,common salt surrounded with 15cm all around the plate all as specified and shown in EP-3 of SSR Part-I

Supply and replace environmental friendly, ultra modern, energy saving, surface mounted, decorative oval bulk head edge-lit led luminaire comprising of high brightness leds of capacity10 Watt. Make: Havells or equivalent in Philips/CG/WIPRO

Material and labour for old size brick well burnt, laid flat, for cable protection complete all as specified and directed.

S&F in replacement sheet metal enclosures distribution boards,vertical type double door three phase 415 volts 4 ways (one incoming three phase & four out goings three phase )for MCCB,ISOLATOR&MCB,s comprising three phase four wire copper strip bus bar of appropriate capacity complete all as specified and directed and comprising of the following (a)MCCB FOUR POLE 63 AMPS AC 415 VOLTS 16 KA IHLGNF0063 =01 NO as incoming (Note :- (i)The DB shall be VTPN series of MDS-LOADKONTAKT/Havells - CAT PART – DHDPTVODRW04 or equivalent L&T , ABB . (ii) The DB shall be flush fixed ,and making good the disturbed surface matching with existing specifications shall be part of job at no extra cost.(iii)connection of theMCCBs/ MCBs with cable shall be made through appropriate size pin /bottle type thimble -properly crimped.(1v) all the vacant holes of the DB shall be provided with blank plates of appropriate size.

Supply & fix exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver . Make : CG/HAVELLS/USHA Note: Fixing of Exhaust Fan on wall with suitable size anchor bolt , making hole in wall for groutng and making good the disturbed surface including plaster work shall be part of job at no extra cost.

S&F cockroach trap grating AISI-304 of size 150 x 150mm square in shape with 5mm border complete all as specifiedin all respect.

M/S RAJ KUMAR GUPTA

Jawandha Enterprises

Vipin Kumar and Brother

M/S Mukesh Kumar Gupta