M and R TO VAJRESHWARI R.R.W.S. SCHEME Tal.Bhiwandi Dist. Thane

Labour salaries to paid to M&R staff for operating and repairing Pise Dhamangav R.R.Water Supply Scheme Tal. Bhiwandi and making water supply to all villages without interruption as far as possible as per terms & conditions as well as sallent features of work to be maintained operuted & repairs.1) Pump operator/Driver- 3 Nos. with daily rate Rs. 641/- 2) Ass. Fitter- 4 Nos. with daily rate Rs. 641/- 3) Helper- 2 Nos with daily rate Rs. 622/-, Total Monthly Amount Rs. 114240/- Total Yearly Amount Rs. 1370880/-

PART- ACurrent Repairing to existing pumping machinary of raw water and pure water pump 10 HP 2 No and 15,20 HP including all necessary repairing.Daily maintenance of existing motor pump at Regional Water Supply Scheme. In case of malfunction of motor and panel, repairing and restarting water supply from time to time, maintaining necessary power plant, adopting electrical deadlock and anti-static, less electricity should be used, employing trained pump operator to handle motor pump, informing the department in case of malfunction of motor pump and repair. Repair orders should be recorded and a pump logbook should be maintained. Supplying, fixing and commissioning MCB type change over switch 4 pole, 63A with 3 positions (I-O-II) with centre off position as per specification no. SW-SWR/MCBCOS

Supplying and erecting iron clad cut out HC type 415V 200A erected on polished wooden block complete.

Supplying & erecting HRC fuse cartridge 415V 200A complete.

Providing & erecting epoxy straight through joint outdoor/indoor for LT XLPE armoured cable 2.5 to 16 sq. mm. cable, with necessary material as per specification no. CB-JT/LT

Providing earthing with copper earth plate size 60 x 60 x 0.315 cm with funnel with a wire mesh for watering and brick masonry block C.l. cover with minimum 25 kg Carbon based environment friendly back fill Ground Enhancing compound complete with all materials, testing & recording the results as per specification no ESE -LA

Supplying & replacing contactor for Star Delta motor starter from 12.5 H.P. to 15 H.P.

Supplying & erecting automatic control panel for 3 Ph, 415 volt, A.C. Submersible/centrifugal pump set up to 7.5 HP - 10 H.P. consisting of DOL starter having relay range 28-42 AMP,S.P.P., Combined ammeter/voltmeter,phase indicating lamp enclosed in CRCA powder coated Vibration proof enclosure with IP 54 protection. Control Panel should offer single phasing, phase reversal, phase imbalance etc.

Supplying & erecting automatic control panel for 3 Ph, 415 volt, A.C.Submersible/centrifugal pump set up to 20 HP consisting of Star Delta starter having relay range 28-42 Amp, S.P.P., Combined ammeter/ voltmeter,phase indicating lamp enclosed in CRCA powder coated Vibration proof enclosure with IP 54 protection. Control Panel should offer single phasing, phase reversal, phase imbalance etc .

Replacing the existing nondriving end bearing of original make for electric motor A.C single phase / 3 phase 12.5 H.P.to 20 H.P. of all types with Required alignment of the shaft and testing the same.

Desilting the Supply Well, Intake Well / Head Works, sump of water supply/ sewerage works etc. in wet or dry condition including lifts upto 9 M and lead upto 150 M as required beyond the work site, stacking, spreading, including necessary guarding, etc. complete, as directed by Engineer-in-charge.

Painting of feeder pillar / switchgears and frame of panel board with single coat of red oxide & two coats of approved quality enamel paint by scrapping existing paint painting the same complete. (while calculating square meter area, area of angle iron frame on which the switchgears are erected shall be considered if required)

Dismantling the existing submersible pump with GI pipeline upto 10 m depth. (For additional depth of each 3 m or part there of add Rs.50/- per 3 m, in the rates)

Providing,erecting and giving test of 150mm diameter submercible pumps set confirming to IS 8043 and IS 9283 pump shall be sutaible for various delivery head and discharge with stainless steel pumps shafts and bronze impellars. Motor suitable for working on 415 volts +10% 3 ph,50 hz AC supply. suplly cable guards, thrust carbon/ fiber bearing to accept entire hydraulic thrust, waterproof winding shall be provided. The pump sets shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacture design. Anti- thrust stream-lined no-return valve shall be provided with pump. Suitable strainer shall be provided 3 core,single/double run copper conducter submersible type flat cable 3 mtr.and two pairs electronic clamps shall be provided along with the pump ( Up to 15 Hp stage) 10 Hp Submersible Pump

15 Hp Submersible Pump

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU 3 core 6 sqmm cable wire

Rewinding of submersible pump motor in borewell of all types and makes above 5 H.P. upto 25 HP with coated copper wires &overhauling with minor repairs, lubricating of ball bearings & bush bearing, and replacing screws etc. testing for the original speed, H.P.and no load consumption & guarantee for one year.

Erecting and giving test of centrifugal pump pumpset with all assembly provided with with accurate levelling with proper alignment including etc complete

Excavation for foundation/pipe trenches in hard murum & boulder including excavated materials including normal dewtering etc complete.

. Excavation for foundation / pipe trenches insoft rock by chiselling where necessary & removing the excavated material & stacking it in measurable heaps within a distance of 50 m from the area & lifts as below, normal dewatering, excluding the backfilling etc complete. ( + 10 % = ) a) Lift 0 to 1.50 M.

Providing andsupplying in standard length polyethelene pipes, confirming to IS 4984 / 14151/12786/13488 with necessary jointing materials like mechanical connector i.e. thread / insert joint/ quick release coupler joint / comprssion fitting joint or flanged joint including al local and central taxes transportation and fright charges, conveyances to the departmental stores / site and stacking the same in close shade duly protting from sunrays and rains, etc complete.. 90 mm dia HDPE Pipe 8 kg/cm2

Dismantling existing dead pipe line of AC/GI/PVC/MS/PSC/CI etc including necessary excavation and stacking as directed by engineer etc complete CI pipes 150 mm dia CI pipe

GI/HDPE pipes 80 mm dia CI pipe

90 mm dia HDPE Pipe 8 kg/cm2

Item No. 5):- Providing & supplying ISI mark C.I.pipes Of following Class. & Dia including all local & central taxes, octroi, inspection charges, transportation to stores, etc. complete. 150 mm dia. DIK-7 pipe

Item No. 6):-Lowering , laying & jointing with SBR ruber gaskets C.I. S/S pipes of various classes with CI MS specials of following class & dia. Including conveyance from stores to site of work, all labour, giving satisfactory hydraulic test, etc. complete either underground or in vertical position as directed by Engineer-In-Charge. 150 mm dia. DIK-7 pipe

Item No.08) Providing and supplying ISI standard D.I. specials &fitting with sealing ruber gasket of S.B.R. complete with cast iron follower gland and M.S. nut bolt coated or otherwose protected from rusting and suitable for D.I. pipes including cost of labour materials and transportation to store/site,loading and unloading including all labour etc. complete as per IS 9523 For all types of specials,bend tees. Etc 80 to 300 mm dia

Providing and supplying ISI mark GI pipe of following class and dia including all taxes,loading and unloading, octri,transportation including etc complete. 80 mm dia GI pipe ISI mark

Lowering and laying, jointing of ISI mark GI pipe of following class and dia including hydraulic testing etc complete. 80 mm dia GI pipe ISI mark

Providing and supplying C.I. detachable joint suitable for A.C. pressure pipe manufacture as per IS 15380-1538-1993 standerd of following class and dia. Including cost of all taxes insurance unloading from railway freight inspection charges and cost of ruber rings nut bolt etc complete. 150 mm dia

80 mm dia

Proiding and supplyingAir valves as per IS 14845 -2000 and MJP's standards specifications of approved make and quality of following dia including all taxes ( central and locals ) railway freight,inspections charges, unloading from railway wagons, loading into truck,transportations up to departmental stores / site, unloading and stacking etc,complete. Air valves 25 mm diameter PN 1.0

Air valves 50 mm diameter PN 1.0

Providing ISI mark CI double short body type manually operated sluice valve of following dia including all taxes ,loading and unloading ,transportation etc complete. 150 mm dia Sluice valve PN 1

80 mm dia Sluice valve PN 1

Lowering and laying ,jointing of MJP standard Sluice valve of following class and dia including testing etc complete. 150 mm dia Sluice valve PN 1

80 mm dia Sluice valve PN 1

Providing and laying in situ following grades of C.C.of trap/granite/gneiss metal for foundations and bedding including dewatering, formwork, compacting and curing, finishing, etc complete CC beding M-150

Supply of C. I. Mechanical Compression Flanged / Socket Tailpiece(Popularly known as I TM Flanged…. 150

Supply 80

Supply of CI Mechanical joint Double Socket with branch Flanged Tees dimenisonlly described in Table -19 … 80 x 80 x 80 Tees

Providing and supplying GI special in position with necessary materials etc complete 80 mm dia bend

80 mm dia tees

80 mm dia union

80 mm dia nipple

80 mm dia Elbow

Item No. 12)- Refilling the trenches from excavated stuff with soft material in 15 cm layers with all leads & lifts including consolidation surcharging … etc complete.

Gas cutting (either square cut or V cut) pipes, plates, etc. of thickness. 5 mm to 10 mm

Welding in all positions with required number of runs, for M.S. pipes internally and / or externally including gauging wherever necessary, fixing appurtenances and other accessories in connection with pipe laying work as per specification 5 mm to 10 mm

Providing and supplying TCL and Alum for water treatment including etc complete.