PROVN OF ALUMINIUM JOINERY, TILING, TOILET FITTINGS GEYSERS, CABINETS AND ELECTRICAL UTILITY PTS IN BLDG NO NP-33 AT INF BN UNDER GE (SOUTH) UDHAMPUR

Amount

Demolition of cement concrete (unreinforced) in ground floor and in paving not exceeding 15 cm thickness (below or above ground level), complete all as specified and as directed by Engr-in-Charge.

Demolition of reinforced cement concrete as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work, complete all as specified and as directed by Engr-in-Charge.

M&L for anti-termite treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete, all as specified and as directed by Engr-in-Charge.

Use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) etc to obtain rough flat finished surface of concrete complete all as specified and as directed.

RCC M-25 nominal mix, (using 20 mm graded crushed stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and as directed by Engr-in-Charge.

TMT mild steel bars, 10mm dia and over, as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with and including MS wire (annealed not less than 0.9mm dia) , complete all as specified and as directed by Engr-in-Charge.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, removing all type of vegetation (like peeple tree etc) scrubbing down with water complete, all as specified and as directed by Engr-in-Charge.

Brick work with old size sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:4, complete all as specified and as directed by Engr-in-Charge.

M&L 15mm thick rendering on fair faces of brick or concrete surfaces in cement mortar 1:6, finish surfaces even and smooth without using extra cement, complete all as specified and as directed by Engr-in-Charge.

M&L 15 mm thick rendering in two layer (10mm + 5mm) on fair faces of brick /concrete on wall including facia chhajja etc.surfaces in cement mortar 1:4 and finished even and smooth without using extra cement including mixing Liquid water proofing compund in the proprotion as mentioned in manufacturer's instructions complete all as specified and as directed by Engr-in-Charge. Note : Water proofing compund to be measured and paid for separately as supply only.

M&L 10mm thick rendering on brick or concrete surfaces as in ceiling in cement mortar 1:3, and finish the surface even and smooth without using extra cement, complete all as specified and as directed by Engr-in-Charge.

M&L newly plastered or unplastered surfaces of walls and applying two coat of plastic emulsion paint (Shade approved by GE) over two coat of wall care putty with primer, complete all as specified and as directed by Engr-in-Charge.

M&L for preparation newly plastered or unplastered surfaces of walls and applying two coat of weather proof exterior emulsion paint (APEX or equivalent) over two coat of wall care putty with coat of primer etc, complete all as specified and as directed by Engr-in-Charge.

M&L for preparing new surfaces of ceiling applying two coats of oil bound distemper over a coat of wall care putty with one coat of primer, complete all as specified & directed by Engr-in-Charge.

Complete removing existing treatment of wall surfaces and applying two coat of plastic emulsion paint (Shade approved by GE) over two coat of wall care putty, complete all as specified and as directed by Engr-in-Charge.

M&L for Complete removing existing treatment (using removal machine) including preparation surfaces of wall and applying two coat of weather proof exterior emulsion paint (APEX or equivalent) over two coat of wall care putty with coat of primer up to G+1 floor height etc, complete all as specified and as directed by Engr-in-Charge.

M&L for Complete removing existing treatment of wall applying two coats of wall care putty and applying two coat of oil bound distemper over a coat of primer with complete all as specified & directed by Engr-in-Charge.

Description all as per Srl item No 17 above but Ceiling.

75mm thick Plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in sub base to floor, complete all as specified and as directed by Engr-in-Charge.

M&L for marble tile makrana (black/ green) marble 18-20 mm thick machine cut, bedded jointed and pointed with grey cement slurry including cutting and polishing over and including 20 mm thick CM 1:3 mortar backing for fixing the stone slab, complete all as specified.

M&L for marble tile 18-20 mm thick machine cut, bedded jointed and pointed with grey cement slurry including cutting and polishing over and including 20 mm thick CM 1:3 mortar backing for fixing the stone slab, complete all as specified.

75 mm thick plain cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregates) as in plinth protection complete, all as specified.

Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar, barred iron doors; ladder, framed balusters; railing; frame work for water tanks, cooler stand etc and similar work conforming to FE 290-0 or Gde-E-165, complete all as specified and as directed.

First class hard wood as in plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and as directed by Engr-in-charge.

40mm thick flush shutters, solid core construction, with particle board core and plywood face pannels on both side and both face is covered with decorative face veneer with liping/frame to match, complete all as specified and directed by Engineer-in charge.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm prelam colour PVC sheet reinforced with M.S. Square tube in opening as per specification & drawing, complete all as specified and as directed by Engr-in-Charge.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck in side with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and as directed by Engr-in-Charge.

S&F 18mm thick plain PVC board, medium density, complete all as specified and as directed by Engr-in-Charge.

S&F 18mm thick prelaminated wooden grain PVC board, medium density, complete all as specified and as directed by Engr-in-Charge.

S&F Sliding rails for Drawers, complete all as specified and as directed by Engr-in-Charge.

S&F Stainless steel trolly for Drawers, complete all as specified and as directed by Engr-in-Charge.

Supply only cabinet hinge spring self closing type, complete all as specified and as directed by Engr-in-Charge.

S&F 100mm Stainless steel decorative drawers/ cabinet handles, complete all as specified and as directed by Engr-in-Charge.

S&F 150 mm Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed, complete all as specified and as directed by Engr-in-Charge.

300 mm Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and as directed by Engr-in-charge.

S & F 125 Butt hinges, extruded brass, with mild steel hinge pin, bright polished and fixed, type C-12, complete all as specified and as directed by Engr-in-Charge.

M&L 150 mm length Brass handles, cast type, polished bright Extruded brass handles, fabricated type polished, complete all as specified and as directed by Engr-in-Charge.

M&L for French polishing on surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two or more coats, complete all as specified and as directed by Engr-in-charge.

Preparation of new/old wooden or wood based surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed by Engr-in-Charge.

S&F 18/19mm thick Plywood, grade BWR, type BB, fixed with screws to timber frame work as in cup boards/cabinets etc, complete all as specified and as directed by Engr-in-Charge.

S&F 12mm thick Plywood, grade BWR, type BB, fixed with screws to timber frame work as in cup boards/cabinets etc, complete all as specified and as directed by Engr-in-Charge.

0.9 mm thick decorative laminate type -1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructuions all as specified and directed.

1.50 mm thick decorative choice of lamination type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive 1.5 mm thick, complete all as specified and directed.

6.4mm thick beveled edge glass of area n exc 0.5 Sqm of each as in shelves of size and shape as required at site, complete all as specified and as direceted by Engr-in-Charge.

Stack clamps out of 50mm by 5mm flat iron and 6mm dia round iron stays,including bolts and nuts and securing ends of stays to wall or roof for 100mm bore of pipe complete all as specified and as direceted by Engr-in-Charge.

Continuous ( piano) hinges mild steel ,bright finish or electrogalvanised , width of flap (when open ) 30mm , complete all as specified and as direceted by Engr-in-Charge.

M&L 100 mm length Brass handles, cast type, polished bright Extruded brass handles, fabricated type polished, complete all as specified and as directed by Engr-in-Charge.

S&F 100 mm designer brass barrel tower bolts,with cast or sheet and rolled or cast bolts, complete all as specified and as directed by Engr-in-Charge.

S&F for brass mortice lock of 4 levers 30 mm thick cup boards, complete all as specified and as directed by Engr-in-Charge.

100mm size Brass hasp and staple powder coated with hinge pin including bolt to hinge plate and fixed with screws, complete all as specified and as directed by Engr-in-Charge.

S&F Brass 40 mm dia cupboard knobs fixed with nut, screw and washer of mild steel bright finish, complete all as specified and as directed by Engr-in-Charge.

Roughening surfaces of old concrete surfaces by picking up, sweeping, cleaning and washing down with water to remove dust etc including taking down tarfelt and brushing neat cement slurry @ 3 kg/Sqm including 10mm thick screeding in CM (1:3) finished even and smooth mixed with water proofing compound (WPC shall be measured and paid separately). Applying bituminous primer on roof surfaces @ 0.40 ltr/Sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 Kg/Sqm and provide modified polymeric five layred APP (Atactic Polypropylene) Modified Polymeric Membrane with 100 micron high molecular high density polyethylene film. Min wt of membrane will be 3.5 Kg/Sqm and bonded completely to the surfaces with min end overlap of 15 cms and side lap 75 mm (overlaps to be bounded with thermo fused by flame) and over APP applying one coat of hot blown bitument 85/25 @ 1.2 Kg/Sqm blinded with fine sand in dry condition @ 0.5 Kg/Sqm, complete all as specified and as directed by Engr-in- Charge.

25 mm thick, Plain cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in sub base for laying floor finishes including finishing the surfaces even and rough without using extra cement, complete all as specified and as directed by Engr-in-Charge.

Supply only Integral water proofing compound, complete all as specified and as directed by Engr-in-Charge.

Plain cement concrete1:2:4 type B-0 using 12.5mm graded aggregated stone aggregates as in lintels upto 1.50 metre clear span,cills, steps; seismic and other similar bands,plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary form works complete all as specified and as directed by Engr-in-Charge.

110mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified and as directed by Engr-in- Charge.

110 mm bore PVC SWR bends any radius with acess door and fixed solvent etc complete all specified and as Directed (ISI Marked)

Vitrified tiles (double charged) of 10 mm thick any colour (square/ rectangular) polished, area of each tile exceeding 0.42 sqm but not exceeding 1.00 sqm as in floors jointed in cement slurry and pointed in white or coloured cement to match the existing surfaces over and including 15 mm thick screed bedding/ backing layer in CM 1:4, complete all as specified and as directed by Engr-in-Charge.

All as per serial item No. 58.00 here in before but on vertical surfaces as in skirting/dado over and including 10 mm thick screed bedding/ backing layer in CM 1:3, complete all as specified and as directed by Engr-in-Charge.

Vitrified tiles (Dark shade) of 10mm thick any colour (area of each tile n exceeding 0.38 sqm) as in floors jointed in cement slurry and pointed in white or coloured cement to match the existing surfaces complete all as specified and as directed by Engr-in-Charge.

110mm bore, PVC (SWR) couplers for PVC pipes and similar work, complete all as specified and as directed by Engr-in- Charge.

S&F Aluminium (Die cast) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 68 kg complete all as specified and as directed by Engr-in-Charge. (ISI Mark)

S&F for harrison rails, drapery rod powdered coated including brackets and necessary fitting, complete all as specified and directed by Engr-in- Charge.

Non skid, coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10 mm thick screed bed or bedding layer in cement mortar 1:4, complete all as specified and as directed by Engr-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by Engr-in-Charge.

Glazed coloured ceramic jointfree/rectified tiles 300x600mm and 7 to 8mm thick in vertical surfaces like dado/skirting, etc., set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10 mm thick rendering on fair faces of brick/concrete surfaces works in cement mortar 1:3, complete all as specified and as directed by Engr-in-Charge.

Factory Made, Machine pressed / vibro mechanically floated coloured interlocking cement paver block ISI marked, any shape and size conforming to IS 15658-2006 of 60mm thickness, M-35 Grade, with topping of cement with imported pigment complete all as specified and as directed by Engr-in-Charge. Shape shall be approved by Engr-in-Charge.

S&F chromium plated Glass shelf with chromium plated guard rails, Make Somany Cat Part No. (WEC 120305) cistern 120714 Seat Cover 121311 Twin flush cistern 120627) UNIEK, complete all as specified and as directed by Engr-in-Charge.

Supply and fixing Vitreous China WHB coloured 615 x 510 mm with pedestal, Make CERA CARNIVAL Cat Part No (WHB 1009, Pedestal 1108), complete all as specified and as directed by Engr-in-Charge.

32mm size waste coupling of PTMT (half or full threaded) (Minimum weight 32mm-45gms/40mm-60 gms), complete all as specified and as directed by Engr-in-Charge.

Supply only 32 mm dia PVC waste pipe, for low level cistern, complete all as specified and as directed by Engr-in-Charge.

S&F 15mm bore centre hole basin mixer with round spout with 450mm long copper pipes and brass nuts without Popup, Make: Jaquar Cat Part No. CON-167KNB, complete all as specified and as directed by Engr-in-Charge.

S&F Bib taps , fancy type cast copper alloy, chromium plated, with crutch or butterfly handle screwed down for iron pipe or for brass ferrule for bore of pipe 15 mm, Make: Jaquar Cat Part No. CON-107KN, complete all as specified and as directed by Engr-in-Charge.

S&F Angular stop cock/Angle cock with wall flange, fancy type, brass, chromium plated, screwed down for iron pipe or for brass ferrule for bore of pipe 15 mm, Make: Jaquar Cat Part No. CON-059KN, complete all as specified and as directed by Engr-in-Charge.

S&F 450mm long braided hose with M10X1 Nipple, 15mm nut, O-ring and rubber washer (suitable for basin) Make: Jaquar Cat Part No. ALD-803AB, complete all as specified and as directed by Engr-in-Charge.

S&F 450mm long braided hose with two 15mm nuts and rubber washers without nipple, Make: Jaquar Cat Part No. ALD-805B, complete all as specified and as directed by Engr-in-Charge.

S&F chromium plated toilet paper holder, Make: Jaquar Cat Part No. ACN-1153N, complete all as specified and as directed by Engr-in-Charge.

S&F chromium plated Glass shelf with chromium plated guard rails, Make: Jaquar Cat Part No. ACN-1171N, complete all as specified and as directed by Engr-in-Charge.

S&F Brass chromium plated 600 mm long towel rail, fancy type, Make: Jaquar Cat Part No. ACN-1111NM, complete all as specified and as directed by Engr-in-Charge.

S&F Brass chromium plated soap dish, Make: Jaquar Cat Part No. ACN-1131N, complete all as specified and as directed by Engr-in-Charge.

S&F Double coat hook, brass chromium plated, Make: Jaquar Cat Part No. ACN-1161N, complete all as specified and as directed by Engr-in-Charge.

Powder coated aluminium frames for door/ windows/ ventilators with one or more rebates and aluminium windows and ventilator shutter frames jointing cleats for fixing and partition wall frame etc , complete all as specified and directed, thickness of powder coating not less than 50 micron complete all as specified and directed. Note: Powder coated aluminium coating colour, complete all as specified and as directed by Engr-in-Charge.

S&F 5 mm thick figured glass (frosted) ,pin head type and glazing with oil putty not exc 0.50 Sqm in each pane along with aluminium glazing beading of size 19.00mm x 17.5mm x 0.70 mm @ weight of 0.097 Kgs per RM including rubber gasket on both side complete alongwith neoprane lining all as specified and directed by Engr-in-Charge.

Power coated aluminium anodised double shutter ventilator (glazed and wire gauge) top hung with aluminium ventilator frame or chowkat 1.5 mm thick aluminium anodised of size 100 mm x 44.5 mm and ventilator shutter frames glazed and wire gauze 1.5 mm thick aluminum anodised of size 44.5x44.5 mm incl aluminium grill and all fitting such as rubber gasket aluminium glazing clips and including 4 mm thick frosted glass pane in glazed shutter fixed with rubber gasket and glazing clip/aluiminium beads aluminium tower bolt 75mm 02 Nos in each shutter , aluminium butt hinges 50 mm 02 Nos in each shutter aluminium handle 75 mm 01 No in each shutter incl all accessories complete all as specified and directed.

Power coated aluminium anodised double shutter window (glazed and wire gauge) side hung with aluminium window frame or chowkat 1.5 mm thick aluminium anodised of size 100 mm x 44.5 mm and window shutter frames glazed and wire gauze (middle, toprail, bottom rail) and styles 1.5 mm thick aluminum anodised of size 44.5x44.5 mm incl aluminium grill and all fitting such as rubber gasket aluminium glazing clips locking cabinet and 75 mm handle and including 4 mm thick tinted glass pane in panes fixed with rubber gasket and glazing clip/aluiminium beads aluminium tower bolt 75 mm 02 Nos , aluminium butt hinges 75 mm 02 Nos in each shutter aluminium handle 100 mm 01 No in each shutter incl all accessories complete all as specified and directed.

Taking down carefully copper /aluminium, point wiring (light, fan, socket or power) complete including fittings and fixtures such as light fittings, switches, ceiling roses, pendants, regulators, sockets etc. and making good disturbed surfaces of wall, ceiling, floors etc, complete all as specified and as directed by Engr-in-Charge.

Point wiring with 1.5 Sqmm PVC insulated, unsheathed (FRLS) cable with multi stranded copper conductor wiring in and including PVC concealed conduit (ISI marked) 20mm dia and over, wall thickness not less than 2.00 mm thick , and all accessories for one light / fan controlled by one switch with 1.25mm thick pressed GI terminal boxes (modular type) of required modules concealed on walls including inner and outer sheet for fixing of modular switches/socket/regulator etc along with PVC insulated and unsheathed FRLS 1.5 Sqmm multistrand copper conductor earth wire connected to common earth and earth dolly, complete all as specified & directed by Engr-in-Charge.

Description all as per item No 89 above but one 3/5 pin 5 Amp socket outlet on the same board with other switch.

All as per description of Serial item No 89.00 here-in-before but one 3/5 pin 5 Amp socket outlet on independent board , complete all as specified and as directed by Engr-in-Charge.

All as per description of Serial item No 89.00 here-in-before but one 3/5 pin 15 Amp socket outlet on independent board with PVC insulated, unsheathed FRLS cable 4 Sqmm copper multistrand conductor, along with PVC insulated and unsheathed FRLS 2.5 Sqmm multistrand copper conductor earth wire connected to common earth and earth dolly complete all as specified and as directed by Engr-in-Charge.

S&F modular switch single pole one way 6 Amps 1 module complete all as specified and directed by Engr- in-charge.

Modular socket, 6Amps, 2 in 1, 6 pin combined 2 module, complete all as specified and as directed by Engr-in-Charge.

Modular socket, 6/16Amps, 2 in 1, 6 pin combined 2 module, complete all as specified and as directed by Engr-in-Charge.

S&F modular switch single pole one way 16 Amps 1 module complete all as specified and directed by Engr- in-charge

Ceiling rose, surface bakelite 65x 50mm two to three terminals fixed on PVC Round Block, complete all as specified and as directed by Engr-in-Charge.

S&F Exhaust fan, steel body, 300mm sweep, AC single phase ,230 Volts, including blades, frame,louvers etc., complete all as specified and directed by Engr-in-Charge.

S&F Exhaust fan, PVC body, 250mm sweep, AC single phase ,230 Volts, including blades, frame,louvers etc., complete all as specified and directed by Engr-in-Charge.

S&F Wall fan, 450mm sweep, AC single phase ,230 Volts, including blades, frame,louvers etc., complete all as specified and directed by Engr-in-Charge.

Decorative ultra slim linear surface mounted LED lighting fixture (4 feet length), 20Watt LED with integral electronic driver complete making connection and testing after fixing all as specified and directed by Engr-in-charge.The specification of light fitting should meet the following : - (a) Housing of Light fitting : Aluminium Extruded (b) Operating Voltage : Between 150 V- 270V (c) Operating Temperature : -10 to +45 Degree Centigrade (d) Lumen efficacy : Not less than 110 lm/W (e) System Lumens : Not less than 2000 lm (f) Colour Temperature : Not less than 5700K (g) Surge Voltage Protection : Up to 2KV (h) Ingress protection : IP 20 (j) Total Harmonic Distortion (THD) : Not less than 20% (k) Power factor : Not less than : 0.90 (l) Line protection : Under/Over voltage Protection (m) Input Frequancy : 50 Hz

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and as directed by Engr-in-Charge.

Supply and fixing wall mounted LED Decorative luminaire with suitable for 12 watt LED, B-22, fixed in repair, including 1x12 watt LED Lamp retrofit type, B22 with all fitting and acessories complete making all connections using 1.5 Sqmm copper conductor multistrand PVC insulated 2 core flexible cable from ceiling rose to fitting complete all as per the directions of Engg-in-Charge. Note : (i) A certificate from the manufactures for warranty minimum upto 3 years shall be obtained and submitted to the AGE/GE (ii) Any touch up of the wall surface due to changing of fittings shall be done by contractor with similar surface finish without extra cost to the department.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. , complete all as specified and as directed by Engr-in-Charge.

Sheet metal enclosures for distribution board when MCB to be used SPN 12 way with IP-43, IK-09 protection 240V with 200 Amps rated bus bar, double door type including cutting chases in walls for fixing DBs making good the distubed surfaces to match with existing specifications ,fixing in repairs complete all as specified and as directed.

MCB SP, 6 to 32 Amps,240 Volts, rupturing capacity 10 KA "C" Series including providing aluminuium thimbles for outgoing cable fixed in repairs, complete all as specified and as directed by Engr-in-Charge. Note : The exact capacity of MCB shall be as directed by Engr-in-Charge.

MCB SPN, 6 to 40 Amps, 240 Volts, rupturing capacity 10 KA "C" Curve including providing aluminuium thimbles for outgoing cable fixed in repairs, complete all as specified and as directed by Engr-in-Charge. Note : The exact capacity of MCB shall be as directed by Engr-in-Charge.

MCB TPN, 4-pole ,40 Amps, 415 Volts, rupturing capacity 10 KA including providing aluminuium thimbles for outgoing cable, complete all as specified and as directed by Engr-in-Charge. Note : The exact capacity of MCB shall be as directed by Engr-in-Charge.

VTPN distribution board,vertically including MCCB 63 Amp , 16kA (as incommer) 4 way, double door IP-43 protection, complete all as specified and directed by Engr-in-Charge. (Including all PCC & cementing work for installation of TPN DB to wall ).

Sub main wiring with two runs of 6 Sqmm ( 2x6 sqmm ) 1100 volts grade single core FRLSH PVC insulated unsheathed multistranded copper conductor conforming to IS-694 drawn through and including non-metalic PVC rigid concealed conduit 25 mm dia medium grade (ISI marked) with all conduit accessories mounting on suface of walls /roofs / ceiling etc with one run of 4 Sqmm (1x4sqmm ) single core FRLSH PVC insulated unsheathed copper conductor cable as earth wire, fixed in repair, complete all as specified and directed by Engr-in-Charge. Note:- 2 runs of 6 Sqmm (2x6sqmm ) ,one run of 4 Sqmm (1x4 sqmm ) cable and one metre of conduit will be measured as one unit.

Sub main wiring with two runs of 4 Sqmm ( 2x4 sqmm ) 1100 volts grade single core FRLSH PVC insulated unsheathed multistranded copper conductor conforming to IS-694 drawn through and including non-metalic PVC rigid concealed conduit 25 mm dia medium grade (ISI marked) with all conduit accessories mounting on suface of walls /roofs / ceiling etc with one run of 2.5 Sqmm (1x6sqmm ) single core FRLSH PVC insulated unsheathed copper conductor cable as earth wire, fixed in repair, complete all as specified and directed by Engr-in-Charge. Note:- 2 runs of 4 Sqmm (2x4sqmm ) ,one run of 2.5 Sqmm (1x2.5 sqmm ) cable and one metre of conduit will be measured as one unit.

Supply and fix sheet metal enclosure Single pole & neutral with 2 pin and earth plug and socket 20Amps, 240V complete with one double pole MCB of any cap from 20 to 32 Amps of breaking capacity 10KA, complete all as specified and as directed by Engr-in-Charge.

RAMAN CONSTRUCTION CO

khajuria builders

s l sharma and sons

SHIVAE CONSTRUCTION

anil construction co.

RAJ MOHD