GE/CHM-100/2022-2023 SPECIAL REPAIR TO ROOF TREATMENT PROVN OF BATROOM ADDN / ALTN TO SEWAGE LINE AND HARD STANDING AT CHANDIMANIDR MIL STN

Amount

Disconnecting existing tanks, setting aside (or lowering if required) for repair, cleaning works etc and hoisting if required reconnecting and refixing in position of capacity exc 500 ltrs but n.exc 1000 ltrs, complete all as specified & directed.

Taking up or down steel tubing and connections 15mm bore, complete all as specified and directed.

Taking up or down steel tubing and connections 20mm bore ,complete all as specified and directed.

Brass Elbow 16 mm for CPVC Pipe, all as specified.

Brass Elbow 20 mm for CPVC Pipe, all as specified.

Brass Tee 16 mm dia UPVC pipe,, all as specified.

Brass Tee 20 mm dia UPVC pipe, all as specified.

Male Brass Threaded Adaptor 16 mm dia (MTA/ MBTA) for CPVC pipe, all as specified.

Male Brass Threaded Adaptor 20 mm dia (MTA/ MBTA) for CPVC pipe, all as specified.

Female Brass Threaded 16 mm dia Adaptor (FTA/ FBTA) for CPVC Pipe, all as specified.

Female Brass threaded 20 mm dia adaptor (FTA/ FBTA) for CPVC Pipe, all as specified.

16 mm (outer dia) CPVC pipes, SDR 11 and Plain CPVC SDR 11 fittings, fixed on walls/ceiling or laying in floors, complete all as specified.

20 mm (outer dia) CPVC pipes, SDR 11 and Plain CPVC SDR 11 fittings, fixed on walls/ceiling or laying in floors, complete all as specified.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings etc and cutting chases for concealed water tubing & making good, cutting not exc 10 cm girth, in brick walls complete all as specified and directed.

Dismantling of existing brick tiles or terracing tiles single layer on roof grouted in cement mortar and removal of any existing treatment , complete all as specified & directed.

Demolition of mud phuska as in roof of any thickness including plastering and leeping etc ( wheater full thickness removal or only a part thereof ) with and including removal of debries/ surplus matrial and soil etc out side MoD land treatment complete all as specified & directed.

3mm thick Atactic polypropylene polymer (APP) based polymeric membrane minimum weighing 3kg/sqm and reinforced with polyester non woven fabric (weight not less than 150 gms/sqm) laid over a coat of oil bound bitumen primer @0.40L/Sqm by same membrane manufacturer of density 0.87 to 0.89 kg/L at 25° C temperature and viscosity 70 to 160 CPS. The membrane shall be laid using butane torch and sealing all joints etc having 75mm side lap joint and 100m end lap joint after preparing the surface as per standard practice and as per manufacturer instructions and finished including dismantling existing felt complete all as specified & directed.

Rendering 15mm thick (average thickness) plaster in cement mortar 1:4 mixed with WPC on concrete roof surfaces including flashings and junction of parapets etc , finishing the surface even and fair without using extra cement all as specified and directed by Engineer-in-charge. Note :- WPC will be measured & paid separately as supply only).

Material and labour 40mm thick brick tiles with including 20mm thick cement mortar 1:4 jointed grouted and pointed complete mixed with crude oil 5% by weight of cement complete all as specified and directed.

All as per serial item No 19 herein before but except tiles –ditto-

Plain cement concrete 1:3:6 type C-1 as in roof padding, 75mm average thickness, terraces and in other similar locations as per site requirement , complete all as specified and directed.

Providing 15mm thick polymer modified plaster in ratio 1:10 over slab ( 1 part of polymer and 10 parts of cement with solid contents not less than 30%) and applying priming coat of epoxy primer with resin and hardner with water dilution as per manufacturer instructions, applying 1st coat of solvent based polyurathene liquid membrane not less than 500 micron thick @ 0.61 Kg/ Sqm and applying 2nd coat solvent based polyurathene liquid membrane not less than 500 micron thick @ 0.61 Kg/Sqm over dried 1st coat, uncluding roughening of existing roof surface complete all as specified and directed. Note : The works shall be carried out by approved applicator of Asian paints/ pidilite/ STP. Such agency shall have a valid authorization letter from the manufacturer.

Plain cement concrete type B-1 (1:2:4) using 20mm graded crushed stone aggregate as in seismic and other similar bands, shelves, copings, bed plates, hold fast, plinth courses and the like finished fair & even, including necessary formwork complete all as specified.

Plain cement concrete 1:2:4 type B-0 using 12.5mm graded aggregate as in roof kerb stone or mud stops cast in situ and rounded or chamfered on edges and similar work, complete all as specified & directed.

Supply only integral water proofing compound (ISI Marked) complete all as specified & directed.

Self adhesive waterproof bitumen flashing tape 200mm wide duy fixed on crack line / hole of AC/GI sheet as in roof complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store complete all as specified and directed.

PVC (SWR) rain water pipe, 110mm bore, single socketed in any length with rubber ring joints, laid in trenches or in floors, fixed as in repairs complete all as specified and directed.

PVC (SWR) rain water pipe, 110mm bore, single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

PVC (SWR) rain water pipe, 75mm bore, single socketed in any length with rubber ring joints, laid in trenches or in floors, fixed as in repairs complete all as specified and directed.

PVC (SWR) rain water pipe, 75mm bore, single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

PVC (SWR) rain water pipe, 110mm bore, single socketed in any length with rubber ring joints, fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm including nuts bolts etc, fixed as in repairs complete all as specified and directed.

110mm bore PVC (SWR) bend any radius fixed as in repair complete all as specified and directed.

110mm bore PVC (SWR) bend any radius complete all as specified and directed.

75mm bore PVC (SWR) bend any radius fixed as in repair complete all as specified and directed.

75mm bore PVC (SWR) bend any radius complete all as specified and directed.

PVC (SWR) branch pieces single socketed Y equal or unequal 110mm dia, complete all as directed.

PVC (SWR) Tee of 110mm with access door etc, complete all as directed.

75 mm dia PVC (SWR) junction single ( single T ) equal or unequal complete all as specified and directed.

110 mm dia PVC (SWR) junction single ( single T ) equal or unequal complete all as specified and directed.

Steel water tubes, 15mm dia bore, medium grade, galvanized, with all standard fittings and fixed complete to walls, ceiling or laid in floors, complete all as specified and directed. Note: Cutting chases and making good shall be measured and paid separately.

Steel water tubes, 20mm dia bore, medium grade, galvanized, with all standard fittings and fixed complete to walls, ceiling or laid in floors, complete all as specified and directed. Note: Cutting chases and making good shall be measured and paid separately.

PVC (SWR) floor trap 100mm bore, plain with grating incl jointing with solvent cement and making good the disturbed surface to match the existing surface, fixed as in repair complete all as specified and directed.

PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75 mm bore, including jointing to waste pipe set in cement concrete type , complete all as specified.

PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement, fixed as in repair complet all as specified and dircted.

PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement, complet all as specified and dircted.

Taking down existing plaster of any description on brick wall/ concrete surface including racking out joints, hacking for key, scrubbing down with water etc complete, all as specified and directed.

Rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to grade Fe.290.Gde-E-165, complete all as specified.

15mm thick rendering in Cement and Sand mortar 1:4 over brick or concrete surfaces finished fair and even without using extra cement complete all as specified and directed Note : WPC shall be measured and paid separately.

Rendering 10mm thick in Cement and Sand mortar 1:6 over brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

Preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over and including 2mm thick (average) wall care putty and sand papering, complete all as specified and directed.

Applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 Square metre over and including priming coat of exterior primer applied @ 0.90 litre/ 10 Square metre over new surfaces, all as directed.

Preparation of new plastered surfaces of walls and applying two coats of cement base paint, complete all as specified and directed.

Demolition of brickwork built in cement mortar ,complete as specified and directed.

Brick work with sub class ‘B’ bricks of class designation 7.5 all as per IS-1077-1992 (minimum compressive strength of brick 75 kg / Sqcm) old size bricks, straight or curved on plan exc 6 metre mean radius built in cement mortar 1:6 complete all as specified & directed.

Brick work with sub class ‘B’ bricks old size bricks, straight or curved on plan exc 6 metre mean radius built in cement mortar 1:4 as in manholes, septic tanks,soakage well etc complete all as specified & directed.

All as per serial item No. 56 herein before but except bricks (using old serviceable bricks) –ditto-

Brick work with sub class ‘B’ bricks old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 as in manholes, septic tanks,soakage well etc complete all as specified & directed.

Granite stone 16mm thick laid over and including 15mm thick screed bed in cement mortar (1:4), machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite ,including cutting, polishing , as in window cills, treads of stairs, etc including dismantling of old tiles complete all as specified and directed. Note:- In treads of stair/ winodw cills, granite stone used shall be in one piece.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations

Plain cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in foundation, filling and mass concrete complete all as specified & directed.

50mm thick plain cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in foundation, sub base and mass concrete complete all as specified & directed.

75mm thick plain cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in foundation, sub base and mass concrete complete all as specified & directed.

Machine pressed Concrete interlocking paver block, with grey cement and pigment, design as approved, any shape and size conforming to IS 15658-2006 of 60 mm thickness, M-35 Grade laid over and including 25mm thick sand cushioning , complete all as specified and directed

Machine pressed Concrete interlocking paver block, with grey cement and no pigment, design as approved, any shape and size conforming to IS 15658-2006 of 60 mm thickness, M-35 Grade laid over and including 25mm thick sand cushioning , complete all as specified and directed

Material and labour machine cut Kota Stone Slab flooring, 18 to 20mm thick, best quality (one piece in stair case tread) over and including cement screed bed 20mm thick in cement mortar 1:6, laid and jointed with grey cement slurry and pointed with grey cement mixed with pigment to match the shade of the slab, cutting, rubbing, grinding and polishing (mirror finish) complete all as specified and directed.

Machine cut kota stone slab flooring 15-18mm thick of one piece in stair case, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab,as in in skirting, dados, risers to steps, pillar etc, laid over and including 10mm screed layer in cement mortar 1:4, cutting, rubbing, grinding and polishing complete, all as specified.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed

Non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 sqm but not exceeding 0.18 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match over and including 15 mm thick bedding layer in CM 1:6, complete all as specified and directed.

Glazed ceramic tiles coloured tile in vertical surface, straight cut /edge , size 450mm x 300mm x 7mm thick ,joint free, first quality, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

Dismantling wrought iron or mild steel as in gates, grills, posts etc or in any description not otherwise provided for, complete all as specified and directed

Dismantling of asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings including ridges, all as directed.

Mild steel screw bolt (machine made) with hexagonal at one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal n.exc 5cm long, diameter of shank 5-10mm, complete all as specified and directed.

Steel work in tubular trusses and tubular posts including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 , complete all as specified & directed by Engineer-in-Charge.

Preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint, complete all as specified and directed.

Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour, having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Excavation in post holes (or similar hole) each in ant type of soil n.exc 0.50 cu m getting out, returning, filling and ramming earth or broken rubble mixed with earth around, in layers not exc 25 cm, watering and removing surplus spoil at a distance not exc 50 metre and making good surfaces complete all as specified and directed.

Plain cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregate as in foundation, filling and mass concrete complete, all as specified & directed.

Surface excavation to required camber and gradient not exceeding 30 cms deep and averaging 15cms deep and getting out in any type of soil, complete all as specified.

Hard core of gauge not exc 63 mm, broken stone or boulders, deposited spread and lavelled in layers n-exc 15 cm watered & rammed to a true surface with broken bricks complete all as specified.

Material and labour hard core of broken brick of gauge n.exc. 63mm, deposited, spread and leveled in layers n.exc. 15cm thick, watered and rammed to a true surface complete all as specified & directed.

Demolition and breaking up drain pipes (Salt glazed stone ware / AC/RCC drain pipe etc) internal dia of pipe 150mm. Set in cement mortar including PCC packing in bed and hunching complete all as specified and directed (excavation and earth work shall be measured and paid separately).

All as per serial item No 82 here-in-before but internal dia of pipe 200mm –ditto-

All as per serial item No 82 here-in-before but internal dia of pipe 300mm –ditto-

Material and labour for RCC pipes class NP2 150mm dia bore, with collars, ISI marked, jointed with cement mortar, laid in trenches and tested including fittings of same grade complete all as specified and directed

All as per serial item No 85 here-in-before but internal dia of pipe 200mm –ditto-

All as per serial item No 85 here-in-before but internal dia of pipe 300mm –ditto-

Plain cement concrete type C-2, 1:3:6 using 40mm graded crushed stone aggregate as in bed to drain pipes including packing under & haunching against the sides of pipes (100mm bore pipe) after the pipe are laid and tested complete all as specified and directed.

Plain cement concrete type D-2, 1:4:8 using 40mm graded crushed stone aggregate as in bed to drain pipes including packing under & haunching against the sides of pipes (150mm bore pipe) after the pipe are laid and tested complete all as specified and directed.

All as per serial item No 89 herein before but 200mm bore of pipe –ditto-

All as per serial item No 89 herein before but 300mm bore of pipe –ditto-

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or ¾ section) in plain cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required, internal dia of pipe 150mm all as specified and directed.

All as per serial item No. 92 herein before but internal dia of pipe 200mm -ditto-

All as per serial item No. 92 herein before but internal dia of pipe 300mm -ditto-

Excavation in any type of soil (hard/dense or mud) for getting out existing damaged/broken or otherwise nonfunctional salt glazed stone ware pipe upto 150mm dia bore (length 60cm), and supply and fixing salt glazed stone ware pipe of upto 150mm dia bore grade 'A' ISI Marked including PCC 1:3:6, type C-2 in bed and haunching as required, including jointing with existing pipes, returning, filling in and well ramming the soil and removal of surplus soil to a distance n.exc 50 m and deposited where directed complete all as specified.

All as per serial item No 95 herein before but bore of pipe 200mm -ditto-

Excavation in trenches in hard/dense soil not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for foundation etc. or for shafts, wells cesspits, manholes, pier hole etc. and getting out, complete all as specified and directed.

Excavation in trenches not exceeding 1.50m wide and exceeding 1.50m deep but not exceeding 3.00m deep for foundation etc or for shaft, wells, cesspits, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in any type of soil and rate also deemed to be included use and waste of timbering as planking and strutting for excavations in trenches in soil, including wales, struts, open poling boards, etc. as may be necessary and fixing and removal all as specified & directed by Engineer-in-Charge.

Excavation in trenches not exceeding 1.5m wide and exceeding 3.00m deep but not exceeding 4.50m deep for foundation etc or for shaft, wells, cesspits, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in any type of soil and rate also deemed to be included use and waste of timbering as planking and strutting for excavations in trenches in soil, including wales, struts, open poling boards, etc. as may be necessary and fixing and removal all as specified & directed by Engineer-in-Charge.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm depth in soils, complete all as specified and directed.

Removal of excavated material to distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point in soil, complete all as specified and directed.

Plain Cement Concrete 1:3:6 type C-2, (40 mm graded stone aggs) as in surface channels and drains , complete all as specified.

Factory made RCC M-35 pre cast man hole covers (Medium duty), of size 600mm x 600mm x 75mm with plain faces, including MS frame, set in position fixed as in repair complete all as specified.

All as per serial itemNo 103 hereinbefore but size 450mm x 450mm x 75mm thick

All as per serial itemNo 103 hereinbefore but size 600mm x 1200mm x 100mm thick

All as per serial itemNo 103 hereinbefore but size 600mm x 1500mm x 100mm thick NOTE : The rates quoted against items 103 to 106 shall be inclusive of steel reinforcement as per IS code complete

100mm bore cast iron soil waste and vent pipes in any length with or without ears with cement joints laid in trenches or in floors, fixed as in repair complete all as specified and directed. (Excavation and earth work shall be measured and paid for separately)

All as per serial item No 107 herein before but 75mm bore of pipes -ditto-

CI 75mm bore branch pieces equal or unequal or inverted (spigot socketed type or with parallel branches fitted with oval excess door), fixed as in repair complete all as specified & directed.

All as per item No. 109 herein before but for 100mm bore pipe -ditto-

Cast iron bends (any radius), diminishing pieces or tapers (largrer bore measured), suitable for 75 mm bore spun pipes, fixed as in repair ISI marked, complete all as specified.

All as per serial item No 111 herein before but 100mm bore of pipes –ditto-

Stack clamps for 100mm bore pipe, made out of 30mm x 2mm size, flat iron round stays, including screws/ Nails and securing ends of stays to wall or roof, fixed as in repair complete all as specified and directed.

All as per serial item No 113 herein before but for 75mm bore pipes –ditto-

CI inspection lid of size 75mm dia for soil and waste pipe including nuts, bolts etc, fixed as in repair complete all as specified and directed.

Removing vegetation, silt, mud, soil etc from a drains of girth exc 30cm but n.exc 2.0m and cleaning and removing debrish exc 50m but n.exc 150m complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm in thickness (below or above ground level), complete all as specified.

Demolition of cement concrete (reinforced) of any description and in any position complete all as specified and directed.

Plain cement concrete (1:3:6) type C-1 using 20mm graded crushed stone aggregate as in plinth protections, 75mm thick, finished fair and even without using extra cement, with 10mm wide joints to full depth @ 3m c/c and at corners, filled with mastic mortar, complete all as specified and directed.

Excavation over areas not exceeding 1.5m deep and getting out hard and dense soil complete all as specified & directed by Engineer-in-Charge.

Excavation over areas in hard/dense soil exceeding 1.5 metre but not exceeding 3.00 metre in depth and getting out complete, all as specified and directed.

40mm thick PCC 1:2:4(using 12.5mm graded stone aggregate) Damp proof course to horizontal or vertical surfaces including necessary formwork complete, all as specified and directed.

25mm thick PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in flooring etc, complete all as specified and directed.

Pressed steel frames 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, including fill of PCC 1:3:6 complete all as specified and directed.

35mm thick flush shutters, solid core construction, with block board core & plywood face panels, commercial type on both sides , BWP,complete all as specified & directed by Engineer-in-charge.

Solid PVC frame having profile 75mm x 50mm , single rebate, made out of solid PVC foam with homogenous fine cellular structure having density 750, smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal screws complete all as specified and directed. (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life)

Factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4 or 6 raised panel design ,solid PVC foam with homogenous fine cellular structure density 750 having smooth outer integral skin, supplying & fixing in frame at site complete all as specified and directed.

Preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

Steel ventilator factory made with top hung shutter including hinges, steel peg stay, a shop coat of red oxide primer, complete all as specified and directed.

3mm thick sheet glass ordinary quality any size and in any type of frame and glazing with oil putty ( or beading ) in square exc 0.5 Sqm in each panes complete all as specified and directed.

Galvanised mild steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm including fixed with tinned tacks or galvanised wire staples complete all as specified & directed.

200mm aluminum anodized barrel tower bolts of extruded section, complete all as specified.

250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed,complete all as specified and directed.

125 mm size aluminium handle (ISI Marked), cast type, anodised complete all as specified & directed.

75mm size, butt hinges, medium weight, cold rolled mild steel including necessary welding if required all as specified & directed

Vitreous China wash basin, white, flat back, size 550 x 400 mm, including fixing acessories like galvanised brackets & rag bolts, , complete all as specified and directed.

Vitreous china squatting pan "orissa" pattern, size 580 x 440 mm white, with integral foot rest (excluding flushing cistern and flush pipe) and making good to the floor, complete all as specified & directed by Engineer-in-charge.

PVC valve less syphonic action type flushing cistern low level white with PVC in let ball valve, float and handle, 10 ltrs capacity and connection to pipes including PVC connection with PTMT nuts and 32mm dia PVC long bend for squat pattern WC , set with concrete and making good to floor, complete all as specified & directed.

Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) , complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as directed by Engineer-in-charge.

Urinal spreader, of PTMT (Minimum weight 60gms) white , suitable for 15mm bore pipe, complete all as specified and directed.

Central hole Basin Mixer, without popup waste system with 450mm long copper pipes and brass nuts, cast copper alloy, chromium plated, screwed for iron pipe or for union, suitable for 15mm bore pipe, complete all as specified and directed.

Soap dish, vitreous China white, embedded in the wall, approximate size 160x 160x90mm all as specified & directed by Engineer-in-charge.

Tubular towel rail Brass CP, 20mm dia, D type, 60cm long between flanges fixed with chromium plated brass screws fixed as in repair complete all as specified & directed by Engineer-in-charge.

Stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, complete all as specified and directed.

Bib taps, fancy type, short body with wall flange, chromium plated, cast copper alloy, screwed down for iron pipe or for brass ferrule, suitable for 15mm bore pipe, complete all as specified and directed.

32mm dia waste coupling / waste fitting of PTMT any colour high-pressure screwed for iron pipe and fixed (minimum weight 45 gms), complete all as specified and directed.

PVC connections 15 mm size with PTMT nuts of length 450 mm fixed in repair, complete all as specified and directed.

15mm bore ball valves high pressure of PTMT with epoxy coated aluminum rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 210gms), complete all as specified and directed.

1000 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) double layered, screwable lid, hoisted and fixed in position, including tank nipple, PTMT 20mm dia ball valve, complete all as specified

Two coats of synthetic enameled paint on steel and iron surfaces over 10 cm width or girth over a coat of red oxide including preparation of new surfaces complete all as specified & directed.

m/s AR Construction co