Construction work of Maharaja Kansha Pasi Memorial Gate in front of village Kasmandi Kala on Navipanaha - Andhe Ki Chowki road under development block

Site Visit & Photograph

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. (DSR 2.31)

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the All kinds of soil.(DAR 2.8.1)

Providing and laying in position cement concrete 1:4:8 (1 cement:4 coarse sand zoneIII:8 graded Stone aggregate 40mm nominal size) of specified grade excluding the cost of centering and shuttering-All work upto plinth level.(DAR 4.1.8)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering finishing and reinforcement - All work up to plinth level:1:1.5:3 (1 cement: 1 coarse sand (zone-III) 3 graded stone aggregate 20 mm nominal size). (DAR 5.1.2)

Steel reinforcement for RC.C. work including straightening. cutting, berding. placing in posiion and binding all complete upto plinth level.Mild steel and Medium Tensile steel bars. As per (DSR 5.22.1)

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc.complete.Electric resistance or induction butt welded tube.(Rate as per DSR 10.16.3)

Crane for hosting in posirtion with derivel and stoff for vehical post & truss and having capacity 50MT as per (DSR 0072)

12 mm cement plaster finished with a floating coat of neat cement of mix : (1 cement: 3 fine sand). As per(DAR 13.7.1)

Retro-ReflectiveSheeting type-XI with 4 mm thick ACM Single Side Providing & fixing of reflective signs with a corrosion resistant 4 mm thick with 0.4 to 0.5 mm both side aluminium skin aluminium composite panel face to be fully covered with High Intensity prismatic sheeting type IV as per IRC-67:2012 retro reflective sheeting with back frame MS angle of 35x35x5 mm. Legends, letters, numerals and borders etc should be as per MoRTH specification No-801.3.7 The sheeting shall have a pressure - sensitive adhesive of the aggressive tack type requiring no heat solvent other preparation for adhesion to a smooth clean surface, in a manner recommended by the sheeting manufacturer. The ACM (Aluminium Composite Materials) shall be fixed on the Back frame MS Angle with riveting. Micro prismatic type IV Retro reflective sheeting confirming to ASTM D4956-09 shall be Pressure fixed. The Retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International/Government Laboratory/ Institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from Indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively, a certificate conforming to ASTM Specification (D 4956-09) on artificial accelerated weathering requirements from a reputed laboratory in India can be accepted provisionally. In such a situation, the Employer/Client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeling as per IRC 67:2012 & Proof of the same Report shall be uploaded which quoting tender. The rate shall include all materials, labour, T&P, transportation, installation and incidentals all complete as per direction of the Engineer-in-Charg.SI No 12 (MoRTH-801)

Less 5% Department Charge