Providing Electric Fencing, ELV, DG set and other allied works at District Prison, Randha, DNH

Amount

(Electrical Works) Point wiring for Light / Bell with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in below type of pipe erected with 6A Modular type switch / bell push & accessories and earth continuity of following type, erected on PVC / Metallic/Wooden box, single mounting base frame covered with textured/metallic front plate modules erected on / in wall / ceiling as per pipe erected, with necessary Lamp holder/ceiling rose / H.D.Connector as directed. (a) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete CAT III

Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of pipe erected with 6A Modular type switch and hum free EME step type electronic fan regulator mounted and accessories with earth continuity of following type erected on PVC / Metallic/Wooden box, single mounting base frame covered with textured/metallic/white front plate modules erected on / in wall / ceiling as per pipe erected. with necessary ceiling rose / H.D.Connector as directed.(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete CAT III

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of pipe erected complete with Modular type switch & 5 pin Plug erected on PVC / Metallic/Wooden box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories. [I] For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu. Wire from nearby switchboard/mcb db board (f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete CAT III

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of pipe erected complete with Modular type switch & 5 pin Plug erected on PVC / Metallic/Wooden box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories. [II] For 16A Plug and 16 amp switch with 2-2.5 sq.mm Cu. Wire from mcb db board. (f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete CAT III

Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC / Metallic/Wooden box, single mounting base frame covered with textured / metallic/white front plate modules erected on / in wall / ceiling with following type accessories

Sheets steel powder coated enclosure suitable for incorporating One/Two nos. MCB.

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) suitable for (B) three phase incoming and single phase horizontal type outgoing Per phase isolation type (PPI) (b) sheet steel double door (i) 4 way

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) suitable for (B) three phase incoming and single phase horizontal type outgoing Per phase isolation type (PPI) (b) sheet steel double door (ii)6 way

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) suitable for(A) single phase incoming and horizontal single phase outgoing (b) sheet steel double door (IP-43) (iv)12 way

providing and erecting Miniature circuit breaker single pole 6A to 25A suitable to operate on 240 V A.C. system and having breaking capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark CAT III

Providing & erecting 240 V MCB double pole switch for lighting Load (B Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box having following capacity (A) 6 to 32 Amp. CAT III

Providing & erecting 240 V MCB double pole switch for lighting Load (B Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box having following capacity (B) 40 Amp. CAT III

Supplying & erecting 20 Amp 10 KA ‘C Curve’ single pole MCB with 20 Amp. Plug socket, company fabricated powder coated sheet steel enclosure erected as directed with connection. [A] Metal Clad Socket with metal clad top CAT III

providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size (a) with medium class Rigid PVC pipe and accessories (d) 3 wire 4 sq. mm

Providing & erecting Approved make Ceiling Fan with double ball bearing ISI mark with Condenser 230 volt A.C.50 Hz. 1200 mm sweep complete having 4 blades Aluminium body and blade sets having ornamental design shanks, canopy erected with earthing [ Make shall be approved by Engineer in Charge]

Supplying & erecting Fan Hook of 10 mm M.S. Round bar grouted in RCC slab with Making the site as original.

Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the RCC bars up to 50mm length each side and pierced through a 16 Gauge M.S. box / Heavy Duty PVC box complete erected concealed in Ceiling with necessary finishing.

Providing Fan clamp of 30 x 5 mm flat of required length & 10 mm M.S. Bolt & Nuts erected with necessary hook of 10 mm M.S. Round Bar.

Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan box.

Supplying & erecting Steel tubular pole (Swaged) confirming to IS - 2713 (Part-II) 1980. Manufacturing process of steel tubular pole should be as per IS specification. Basic steel tube should be ISI Marked. Pole should be painted by one coat of Zinc comet Primer and two coat of Aluminium /approved paint to be erected on / in existing Foundation. The length of poles are as below. (A) 7.5 mtr. Long Swaged Steel tubular pole (i) pole as per IS code 410-SP-4 with 300 X 300 X 4 mm base plate. (Approximate Pole weight 67 Kg) For burial erection

Supplying & erecting Steel tubular pole (Swaged) confirming to IS - 2713 (Part-II) 1980. Manufacturing process of steel tubular pole should be as per IS specification. Basic steel tube should be ISI Marked. Pole should be painted by one coat of Zinc comet Primer and two coat of Aluminium /approved paint to be erected on / in existing Foundation. The length of poles are as below. (A) 7.5 mtr. Long Swaged Steel tubular pole (ii) Add Extra for M.S. Base plate 300 X 300 X 16 mm for pole, Suitable for mounting on surface of foundation with foundation bolts, with required stiffeners welded with pole.

Supplying & erecting Steel tubular pole (Swaged) confirming to IS - 2713 (Part-II) 1980. Manufacturing process of steel tubular pole should be as per IS specification. Basic steel tube should be ISI Marked. Pole should be painted by one coat of Zinc comet Primer and two coat of Aluminium /approved paint to be erected on / in existing Foundation. The length of poles are as below. (A) 7.5 mtr. Long Swaged Steel tubular pole (iii) Add Extra for PU base primer and PU Paint on pole.

Providing street light pole bracket comprising main B Class MS pipe of 4.2 cm/require outside dia. complete with suitable B Class M.S. sleeve tubing of approx. 45cms.length and suitable for 76.5 mm / 80mm. / require size pole top having sufficient fastners for fixing the brackets and having spread of 1 mtr. length with suitable rise as per site condition & suitable welded stiffener reducer and nipple with check nut complete painted with one coat of Red oxide / PU base primer and two coats of Aluminium / PU paint. paint with following nos of arms. [A] Single Arm bracket 1 Mtr

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size (a) with medium class Rigid PVC pipe and accessories 4 wire 10 sq. mm

Providing and erecting water cooler having storage capacity 80Ltr. & cooling capacity 40 Ltr.per hour @ an ambient temp of 45' C. The outlet temp. of the water should drop by 15' C within a hour, The water cooler should be comprising of hermetically sealed compressor, fan motor, condensing unit, water tank surrounded by evaporating coil, thermostats, relay etc. complete with necessary inlet & outlet connection. The body of water cooler will be made from Stainless Steel.

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, in approved manner as directed (b) 25 mm

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, in approved manner as directed (c) 32 mm

Supplying and laying UPVC cable trunking system comprising unplasticised polyvinyl, chloride rigid material with ignition free and flame proof confirming BS with necessary end caps Internal and external bend, flat bends, coupler, tee etc..All necessary accessories and measuring of following sizes 100 mm x 50 mm trunking

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size (a) 2 wire 1.5 sq. mm

Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 kv grade ISI marked copper wires of following size to be erected as directed. 1.50 Sq.mm 3 core round PVC sheathed

Supplying & erecting approved make LAN cable of following size in existing pipe as per direction (C )CAT - 6

Supplying & erecting approved make LAN cable of following size in existing pipe as per direction (e )CAT - 6 (ARMORED cable)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand / Solid Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables. (C) 4 core 6 Sq. mm

Making trench in Hard Murrum / Tar Road of suitable width of 90 cm or required depth for laying any size of cable or locating the fault all over the run and back filling the same and making the surface as normal ground.

Drilling the road without breaking the road surface (Asphalt) for laying of cable for feeding power supply by making up to following size of holes at both ends complete.(A) Up to 100 mm bore dia

Providing & laying approved make Double walled corrugated pipes (DWC) of polyethylene(conforming to IS 14930 II )with necessary connecting accessories of same material at required depth in existing trench for laying of cable. below ground / road surface for enclosing cable (A) 50 mm outer dia

Providing & laying approved make Double walled corrugated pipes (DWC) of polyethylene(conforming to IS 14930 II )with necessary connecting accessories of same material at required depth in existing trench for laying of cable. below ground / road surface for enclosing cable (C) 90 mm outer dia

Providing and erecting ISI Marked 3core 70 Sq.mm XLPE insulated 11 KV armoured cable Aluminium conductor IS-7098 to be laid on wall with clamps or in provided cable trench / pipe approved manner as directed

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables (G) 3 1/2 core 150 Sq. mm ( 70 Sq. mm 1/2 core)

Providing and erecting cable end termination kit, heat shrinkable Push on type Densons’/ ‘Raychem’/ Elastimold make suitable for 11 KV XLPE cable 3 core 50 & 70 Sq.mm (A) Outdoor type

Providing and erecting cable end termination kit, heat shrinkable Push on type Densons’/ ‘Raychem’/ Elastimold make suitable for 11 KV XLPE cable 3 core 50 & 70 Sq.mm(B) Indoor type

Providing, erecting, testing & commissioning approved make oil immersed ONAN cooled, double wound, core type indoor / outdoor copper wound 11KV/ 433V step down transformer of following capacities operating on 3 phase, 50 Hz 4 wire & neutral earthed system continuously rated for a full temperature rise in oil not exceeding 45 Deg.C.at maximum ambient temp. of 50 Deg. C. complete with necessary radiator first filling of new transformer oil & standard fitting as below complying with IS 1180( Part 1):2014 standards with energy efficiency level 2 Off load tap changing range steps +2.5% to -5% on H.V for variation should be provided. The H.V. shall be connected Delta & Secondary with star connection. The transformer should have cable-end boxes on H.T. side suitable for up to 3 core 150 sq.mm. XLPE cable & on L.T. side suitable for bus duct or cables as per requirement complete with test certificates from manufacturers 1. Oil conservator with filling Hole & Cap - One No.2. Thermometer pocket with 6" dial type thermometer switch alarm & trip contacts- Two nos. 3. Silica-gel breather with charge- One No. 4. Plain oil level gauge - One No. 5. Drain / Sampling / Filter valve- One No. 6. Top Filter Valve - One No. 7. Explosion vent with Diaphragm - One No. 8. Rating & Diagram plate - One No. 9. Additional neutral bushing for earthing - One No.10. Bi directional Roller - Four Nos. 11. Earthing terminals - Two Nos. 12. Lifting lugs - Two Nos. 13. Air release plug. - One No. 14. Double float buchholz relay with Alarm and trip contacts. 15. Control cable as required from Transformer to VCB Panel is to be provided with necessary connection to VCB relays for protection. as per IS 1180 level-2 (b)315 KVA Max. allowable loses at 50 % of rated load is 1.025 KW and at full load is 3.1 KW, Cat.III

Supply installation testing and commissioning of 55" 4K LED display, 350 Cd/m2 brightness, HDMI X 2, with required mounting bracket and 10Mtr Hdmi Cable as per site requirement. as per technical specification etc. as required.Make LG,SAMSUNG,SONY

Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value surrounded by highly conductive compound with high charge dissipation suitable for following type of applications with chamber and heavy duty cover.(approved make OEM has to submit test certificate) & having back filling compound of (B) Inner chemical (CCM Compound)- Resistivity:- 0.2 ◻/ meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no load & dry form, Sulphar content:- <2%(C) Back fill Compound :- Earthing compound should be capable to retain moisture for long time Necessary test report must be submitted. (b)For Electrical installation up to 11 KV in normal soil. Length of Pipe : 2.00 mtrsBack filling Compound :1 no. Bag of 25 Kg.

Providing and erecting required size Copper strip for earthing of H.T. OCB / ACB/ Transformer, LT panel board, Motors etc. using copper clamp.

Supply of 11 kv.630 amp. AIR insulated, LBS panel with Earth switch and HRC fuse.

Supplying rubber matting of following thickness as per IS:15652/IEC 61111 (c)12mm

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) suitable for , (B) three phase incoming and single phase horizontal type outgoing Per phase isolation type (PPI), (b) sheet steel double door, (iv)12 way

Supply, Installation, Testing & Commissioning of,4 MP IP Bullet Camera, Line crossing detection (human/vehicle classification); Region intrusion/ entrance/exiting detection (human/vehicle classification), 2 way talk support, Speaker Out,

Supply, Installation, Testing & Commissioning of IP Network TDN Low-Light IR PTZ Camera · 1/2.8” 2Megapixel CMOS · Powerful 25x optical zoom · Starlight technology · Max. 50/60fps@1080P · Perimeter protection · Support PoE+ · IR distance up to 100m · SMD PLUS · IP66 required.Make;Honeywell ;Bosch, Secura,

Supply, Installation, Testing & Commissioning of Outdoor Speaker

Supply, Installation, Testing & Commissioning of Video Wall 86"

Supply, Installation, Testing & Commissioning of CAT6 Cable

Supply, Installation, Testing & Commissioning of Fiber Cable 6 Core armored

energizer should be as follows Input Ampere - 0.500 Amp Peak of o/p voltage: 6.0kv - 10 kv on 500 Ohms load.Pulse interval :- 1.0 -1.2 Sec.Pulse Duration: 0.3 Milli Second Peak current :- 7.0-9.0 A – High RMS Current: - 2.4 – 2.8A – High.With inbuilt10A algorithm based solar Charge controller to protect battery, solar penal and energizer. 1.fence energizer Must ISI marked BIS: 302- 2-76 (1999) with CML number. 2. It should have capability to measure every pulse. Programmable and Adjustable fence siren system. Which can be perform in all weather and all type of soil. Fence touch or break. 3. Energizer should have inbuilt microcontroller based operation and charge controller 10A. Capable to 100W solar penal.4.It should have indicators such as – battery voltage, Fence Fault.chraging,pulse etc. 5. Due to safety Fence energizer should be microcontroller based. 6. Manufacturing should confirm to BIS standard 302-2-76. Must be tested and certified by ISI marked and with valid certificate7. Effective protection for fence up to length - up to 3.5 Km Considering 10 strands of wires.8. Warranty - 1 years. Hooter 120db 12 volt waterproof with 2.5 meter wire Battery connection cable 1 meter length 0.5sqmm 2 core non detachable Solar penal connection wire5 meter length 0.5sqmm 2 core non detachable,Battery charger 240 input and 14VDC minimum 3A output,Battery 12 v 42.Ah (SMF) VRLA or CE/UL Marked or IS: 15549.2025 or IEC-60896 or JISC 8702 any Govt lab. Test certificates is compulsory for supply of battery.UL or CE certified Must be of reputed Brand.Battery with 1 years guarantee.Lightning diverter Chock type With proper erthing system aFlash Tube Red colour flash light ipx4 water and dust proofnd have good insulation.Housing box Should be capable of safety housing battery and energizer with lock & key,H.T Wire 2.5-2.59 mm wire diameter (12 gauge) High tensile wire with minimum of 230- 300 gms, /sq.,zinc coating thickness. Rust free UTS 140.5 kg/mm². Break strength of 740 kgs.Corner/ End post MS hot deep Galvenised,48mm OD square pipe(Medium class)including Nut Bolts with support at end Support post MS hot deep Galvenised,48 mm OD square pipe(Medium class)including Nut Bolts with corner pole at end,Intermediate post MS hot deep Galvenised,32 mm OD square pipe(Medium class)including Nut Bolts with corner pole at endcorner pole Insulators ABS material insulation class 25 KV, UV stabilised maintenance free.Intermediate pole Insulators Zink coated 5 mm metal road moulded ABS material insulation class 25

Providing, erecting, testing commissioning & getting Plan Approval as well as NOC from Electrical Inspector for extensible H.T panel comprising of one 400A. H.T. VCB incoming & Two outgoing 400 A Drawout type VCB confirming as per I.S. for use on 11 KV, 3 phase, 50 c/s. unearthed A.C. supply system having breaking rupturing capacity of 350 MVA complete with spring operated mechanism, mechanically & automatic ON-OFF and spring mechanism charged, discharged indicators, ON-OFF mechanical push button, operation counter necessary auxiliary switches, closing shunt trip, air insulated busbar chamber having heat shrinkable PVC sleeves, mechanical interlocks safety shutters, isolating plugs and a VCB trolley with three vacuum interrupters with epoxy support insulators and self aligning finger type isolating contacts. The breaker shall be Manual cum motorised mechanism & auto spring charge with TNC switch closing with following accessories. 1. flush mounting type digital multifunctional meter with communication facility - Three sets. 2. Power Factor Meter One No 3. Double core current transformer cast resin type having ratio 200 to 50/1 core for metering & second core for protection having required class of accuracy. - Three Sets 4. Instantaneous under voltage relay& Temperature rise Tripping Relay 5. Electrical closing coil & short trip coil operating on 110V. D.C.- Three Sets 6. Auxiliary relay for anti pumping device 7. Three phase Three limb Drawout type feeder connected & output of 200 VA cast resin insulated potential transformer having ratio 12000V./110V. and 200 VA Burdon with 0.5 accuracy. - One No. 8. Common Alarm bell operating on 110V A.C.- One No. 9. Digital KWH Meter - One No. 10. Cable boxes suitable up to 11 KV 3core 150 sq.mm XLPE cable. - Three Nos. 11. 230V. A.C. to 110V. D.C. power pack for closing & tripping circuit common. 12.Breaker ON-OFF, Auto trip and spring charged indicators. - Three Sets.13.Phase indicating & panel illumination lamps with plug socket - Three Sets. 14.Numerical Communicable type non directional O/C & E/F Relay with a setting of 5-250% both in O/C & E/F. -Three Set complete with necessary interconnection with air insulated high grade copper busbar {Breaker Testing scope include Closing Time, Opening Time, VCB Hi-Pot test at Site}{ Relay Testing Scope Include testing of all protection by three phase testing kit at site }(VCB Trolley is to be provided)

Getting Plan Approval as well as NOC from Electrical Inspector for entire Electrical Installations required as per Indian Electricity Act.

Providing pair of rubber hand gloves suitable for working on 11 KV/22 KV supply.

Supply & Installation of hot dip GI ladder type cable tray with all accessories like coupler, GI nut bolts,bend, tee, reduser etc as per specification and drawings complete with all required hardware : 600 x 100 made out of 2 mm thick ladder type

Supplying , fabricating and installation of various sizes clamps for cable tray supports using available M.S. sections & rod as per drawings or instructions of engineer in charge or consultant including applying zinc chromate yellow oxide and two to three coats of required enamel paints with anchor fasteners etc.

Providing and, fixing heavy duty flange type brass double compression type cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. (F) 3 & 1/2 core 150 Sq. mm

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (H) 150 Sq.mm.

Providing & erecting approved make AMF control panel suitable for following size of 3 phase, 415 V., 50 cycles, A.C. diesel generating set complete of scope as detailed below: 1) Power module: A pair of electromechanically interlocked contactors (for mains & generator) Overload relay for generator contactor Neutral contactor for mains and generator Power socket for connections. 2) Control and metering module: Line voltage monitor. Generator voltage monitor Ammeter 3 items attempt start facility. Air circuit breakers/MCB/MCCB of suitable rating for auto/manual operation. Auto/manual switch. Emergency stop push buttons. Manual start push button. frequency meter. Engine hour meter. Two earthing studs. 3) Protection module: The engine shutdown in the unlikely event of Low lube oil pressure High cylinder head temperature. V belt failure. 4) Indicators with alarm Load on generator. 5) Indicators Load on mains Engine fails to start . Emergency stop battery charger. The AMF Panel of following capacity (C) AMF Control Panel for100 KVA/125 KVA3 phase DG Set

SITC computer power supply point with 2 nos of 6 amp 5 pin socket with 1 no. of 6/16 Amp. socket with 1 no 16 A Switch with indicator & wiring of computer point will be done through 2 nos.of 2.5 sq. mm Cu. wires as phase & Neutral and 1 nos. of 1.5 sq.mm.as earth wire. .( This cost includes the wiring from DB to Computer point.)

MV Switch Gear And Power Panel Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. MAIN PANEL AT SUBSTATION As per Single line diagram

Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. EXTERNAL LIGHTING PANEL (OUTDOOR DUTY) As per Single line diagram

Multi pair control cable for interconnection of HT panel to transformer & DG to AMF panel.

Supplying and erecting approved make online Un-interruptible Power Supply system comprising flat cum-boost charger with IGBT base rectifier & Inverter & sealed maintenance free SMF batteries. The charger having operating capacity for input 160-270V AC & inverter having output 230V,50 Hz Ac with 0.8 load power factor with battery, over/under voltage output with over load & short circuit protection equipment. The system housed in CRC sheet duly powder coated paint with following power backup.with MS painted batteries stand, 10% Overload capacity for momentary load. (J) 20 KVA 3 - phase with 1Hr Backup

SITC of Patch Panel Cat 6 UTP Keystone Type- 24 Port-Fully Loaded [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ]

SITC of CAT6 UTP 24AWG PATCH CORD:1M,Plug 30U' Snag less [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ]

SITC of CAT6 UTP 24AWG PATCH CORD:2M,Plug 30U' Snag less [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ]

Providing & erecting Fiber Optic LC style fully loaded Patch Panel (FOPP), 19" Rack Mount with following nos. of OS2 9/125μ Pigtails as per ISO/IEC-11801-OS2 Pigtails with LC Type Connectors Shall have all accessories including coupler plates pre loaded with duplex LC couplers (OS2), pigtails for terminating fibers on the FOPP Pigtail Attenuation ≤0.3dB measured measured against reference connector Return Loss ≥ 45dB, in mated condition Pigtail Cable Information – Outer Jacket Diamter – 0.9mm, Outer jacket colour – white , Outer Jacket Material – LSZH Shall be Front Patching Type, 1U high and rack mountable on standard 19” rack with mounting arrangements (A) 12F Loaded with Coupler, Pigtail and Splice Trays

SITC of PIGTAIL LC SM SIMPLEX LENGTH- 1m [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ]

SITC of PATCH CORD LC-LC SM DUPLEX LENGTH- 3m [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ]

Supplying and making cable route marker with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) of size 60 cm X 60 cm at the bottom and 50 cm X 50 cm at the top with a thickness of 10cm including inscription duly engraved as required. for OFC Marker, as per technical specification etc. as required.

Providing & Erecting Netwrok rack with following capacity with Necessary cooling fan,Cable manager,6A PDU,equipment rack with necessary mounting accessories. (C) 12 U

Supply, Installation, Testing & Commissioning of 42U (800W X 800D) floor mount closed rack complied with UL, CSA, TUV, EIA 310, DIN 41494, DIN 41494, ISO 9001, ISO 14001, IEC 297 and current industry practices, CRCA Steel Door - Plain, Vented at Bottom, Fully perforated at front and rear side, with screw fitted side panels. 19" L type mounting angles at front and rear, top and bottom cover with cable entry provision, with required accessories as per technical specification etc. as required.

Active Components- Data & Voice Networking TYPE-1 Supplying, installation, testing and commissioning of Layer 3 fiber aggregation networking switch, 24 nos. SFP+ fiber optics ports, 1 AC power supply built in and inclusive of redundant power supply and redundant fans as per technical specification etc. as required.

SITC of 24 x 10/100/1000BASE-T ports 4 x Gigabit RJ45/SFP Combo ports Advanced L2 switching and security features L2+ Static Routing Optional “standard mode” or “surveillance mode” management user interface

Type 3 Switch: 16 Port POE Supplying, installation, testing and commissioning of Layer 2 Manageable, Stackable Networking switch having 16 # 10/100/1000Tx ports, all 16 ports shall be capable of providing PoE+ as per 802.3at, switch having a PoE power budget of minimum 370 Watts, minimum 4 SFP+ ports complete as per technical specification etc. as required.

Supply, Installation, Testing and Commissioning of 10G SFP+ LR singlemode transceivers, 1310nm, duplex LC termination supporting distance upto 10000 mtrs, inclusive of any hardware or interfaces such as modules for populating SM-LC transceivers complete as required.

Supply, Installation, Testing and Commissioning of 1G Base-T transceivers, RJ-45 termination supporting distance upto 100 mtrs, inclusive of any hardware or interfaces such as modules for populating RJ-45 Base-T transceivers complete as required.

Supplying, installtion, testing and commissioning of Video Management Software supporting ONVIF Profile S & G, PSIA, real time streaming protocol (RTSP) standards, emerging technologies in the industry, like 4K resolution, H.265 video compression codec, 3D PTZ control, Fisheye camera and multi-imager/ lens camera support, and intelligence events. Software proposed shall have scalability of 128 cameras per server with at least 256 licenses to record all the cameras from the Day 1 and expandable up to unlimited cameras. Videom Managment Software shall support simultaneous recording, live monitoring, playback/search of recorded video for up to 4K resolution on all cameras, taking snapshots and viewing presets for PTZ cameras and system management, Videowall management. Video Management Software shall support - 1) Free Firmware upgrade; 2) Lifetime software licence, must not be renewed periodically; 3) It should support unlimited channels; 4) It should support N:1 and N:M redundancy; 5) It should have calender view for better playback investigation; 6) It should support Smart Motion Detection; 7) It Should support Surrounding View feature of cameras; 8) The camera zoom in/out, controlling and setting should be able done from software; 9) The proposed softsware should be latest versin available from OEM 10) VMS Shall support scheduled backfilling of the recordings from the edge storage/SD card of cameras to the server. For details specification refer tender technical specification etc. as required.

Supplying, installtion, testing and commissioning of Server(s) required for NSM & NVMMS - Industry standard Intel based platform, rack mounted, redundancy architecture for critical hardware components, licensed Microsoft Server operating system and requisite user licenses, licensed application suites, 2 x Quad Core Intel® Xeon latest processors or better, 8 GB of RAM, 2 x 1.2 TB of SAS HDDs, minimum 2 additional hard disk drive bays for expansion, 1,280 x 1,024 Display/ video resolution, 2 X 10/100/1000 ethernet network interface card, Video memory 2GB above, RAID support built-in, DirectX 8.1 above and pre-installed DVD-R/W Drive and Appropriate Licensed Operating Systems as per NSM & NVMMS Requirement. as per technical specification etc. as required.

Supplying, installation, testing and commissioning of Network storage required with a capacity to store the content for 256 cameras for 24Hrs x 30 days at 25fps and 1080p (Minimum 350TB from day 1). It should be scalable (should have sufficient expansion bays for HDDs) for at least additional 50 cameras. Vendor shall submit bandwidth and storage calculator for the proposed camera models, as per technical specification etc. as required.

Supplying, installation, testing and commissioning of Client PC - Industry standard Intel based platform computer system. Intel Core i7 latest generation, 4 GB of RAM DDR3 ,1 TB SATA II hard drive for OS and VMS applications, NVidia card 1 GB graphics card , 1600 x 1200 or higher screen resolution, 1 X 1000Mbps ethernet network interface card ,16x DVD+/- RW Drive alongwith appropriate licenced Operating System, licenced applications suites from OEM and application licences as per the technical specifications etc. as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. (A)Speaker cable Single pair, 2-core, 1.5 sqmm

Supplying, installing, testing and commissioning of VC UNIT of Full HD Video Conferencing system with 1 + 3 Sites Connectivity with HD Communication Camera, Boundary Mic X 2 , Two Monitor Output, Video Input : HDMI X 2 for Camera, RGB X 1 and HDMI X 1 for PC Input, Video Output: HDMI X 2, RJ 45 X 1 for Control Purpose as per technical specification etc. as required.

Supply, Installation Testing & Commissioning 20 ft HDMI Interface Cable as per the detailed Specifications supports transmission of 4K Signals as per the detailed Specifications

Supplying, installation, testing and commissioning of Laser Jet B/W Printer - A4 Size. as per technical specification etc. as required.

Supplying & erecting Amplifier having following specification: Power Output :250W (RMS) (300W Max.) inputs : 6 Misc. & 2 Aux. frequency Response :50-1500HZ I3db Tone Controls :Cut & Boost type LED Meter :5 LED Arrays The amplifier suitable to operate 240V A.C.& 24volt D.C. (Battery) with automatic changeover from AC to Battery operation, duly protected by wrong Battery Polarity connections. [[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ]

SITC of DLP/LCD 4000 Lumens LASER projector compatible with 4K & HDR, IP6X dust resist provides good brightness and reliability, approx 20,000 hours laser light source life and virtually zero maintenance for system, 1.3x zoom, Tilt free orientation, including portrait mode, Native Resolution ,XGS or more Contrast 25,000:1, Light Source Life 20,000 hours to 50% brightness (Eco mode) I/O Connectors HDMI x1, HDMI/MHL x1, VGA in x1, Audio in x 1, Audio out x1, USB Power (5V/1.5A), RS232, Micro USB(FW Upgrade), RJ-45 x1, wireless remote control erected as directed by engineer incharge

SITC of following standard size MW fabric Tab-Tension Tubular Motorized Screen with RF remote, Aspect Ratio-16:9, (E) 133/135 inch Diagonal

Supply, Installation, Testing of 11 KV 3Phase*4 Wire Metering CTPT Unit Accuracy Class 0.2s Ratio : 75/5 Amp. Complete in all respect including all required for the same.

Supply, Installation, Testing of 11 KV 3Phase*4 Wire HT Bi directional Meter Accuracy Class 0.2s Make : Secure. Complete in all respect including all required for the same.

Amitkumar P. Patel (BID ID -20794)