Repair/ replacement of externl water supply line, all type of pump sets and allied works at Mil Stn Beas, 2 ASD area and Jandiala Guru under GE Kapurthala

Amount

Excavation in trenches in soft/loose soil not exceeding 1.50 mtr wide and not exceeding 1.50 mtr in depth for taking out and laying CI/GI pipe complete all as specified and directed by Engr-in-Charge.

Returing, filling in, including spreading, leveling watering and well ramming inlayers not exceeding 25 cms thick each layer complete all as specified and directed by Engr-in-Charge.

Removal of surplus soil to a distance not exceeding 50 mtr away and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed by Engr-in-Charge.

Taking down GI pipe 20 mm bore medium grade and fitting and supply and fixing GI tubing medium grade 20 mm bore in any length with all fitting laid in trench and connecting up with water supply main complete all as specified and directed by Engr-in-Charge. Note:- Excavation and earthwork shall be measured and paid for separetely under approprite item).

All as per item ser No 4 above here in before but 25 mm bore

All as per item ser No 4 above here in before but 40 mm bore

All as per item ser No 4 above here in before but 50 mm bore

All as per item ser No 4 above here in before but 80 mm bore

Taking down old unserviceable GI/CI pipe 80/100 mm bore and supply, laying, jointing and testing new cast iron pipe 80 mm bore centrifugally cast class LA confirming to IS - 1536 spigot and socketed ends in any length laid in trenches complete all as specified and directed by Engr-in-Charge. Note:- excavation, earth work, CI fitting and new run lead joint shall be measured and paid for separetely under appropriate item of Sch 'A')

All as per item No 9 above here in before but 100 mm bore

All as per item No 9 above here in before but DI (K-7)100 mm bore

Taking down old unserviceable GI/CI pipe 150 mm bore and supply, laying, jointing and testing new cast iron pipe 150 mm bore centrifugally cast class LA confirming to IS - 1536 spigot and socketed ends in any length laid in trenches complete all as specified and directed by Engr-in-Charge. Note:- excavation, earth work, CI fitting and new run lead joint shall be measured and paid for separetely under appropriate item of Sch 'A')

All as per item No 12 above here in before but DI (K-7) 150 mm bore

M&L for disconnecting electric connection and pipe connection and taking out submersible pump & motor of capacity 12.5 to 17.5 HP from bore well and taking to workshop for repair and removal of burnt winding wire from motor and rewinding with new PVC insulated copper winding wire for submersible motor of same guage and weight to existing including replacement of , Motor bush, thrust plate coupling complete with key and alignment of motor stater's slote reassembnling the motor with pump and lowering it into bore well making it functional and testing complete all as specified and directed by Engr-in-Charge.

All as per item 14 above here in before but capacity 25 to 30 HP

All as per item 14 above here in before but capacity 35 to 45 HP of turbine motor pump including replacerment of ball bearings.

All as per item 14 above here in before but capacity 100 HP of turbine motor pump including replacerment of ball bearings.

M&L for disconnecting submersible pump from electric motor and taking it to work shop for repair / replacment of unserviceable part of submersible pump capacity 12.5 to 17.5 HP such as gun metal bush impeller assembly remetaling/ turning to shaft, locking key and MS nuts & bolts of existing size and reassembling the pump with motor and making it functional complete all as specified and directed by Engr-in-Charge.

All as per item 18 above here in before but capacity 25 to 30 HP

All as per item No 18 here in before but for submersible pump for capacity 35 HP to 45 HP.

All as per item No 18 here in before but for submersible pump for capacity 100 HP.

S&F Submersible pump set, Electric driven having dischage 1000 LPM at 84 mtr head including suitable capacity of electric motor not less than 45 HP suitable for operation of 415 volts 50 C/S AC supply complete all as specified and directed by Engr-in-Charge.

S&F Submersible pump set, Electric driven having dischage 1000 LPM at 84 mtr head including suitable capacity of electric motor not less than 15 HP suitable for operation of 415 volts 50 C/S AC supply complete all as specified and directed by Engr-in-Charge.

M&L for repairs and servicing of centrifugal pump & Motor sets 100 HP (make M/S BATLIBOI)electric driven Squirrel cage induction motor 3 phase 415 V AC 50 HZ,opening & cleaning inside of 100 HP motor stator, varnishing and drying ,re-winding and duly replacing the following worn out parts of pump and re -erecting, testing and commissioning complete all as specified and directed by Engr-in-Charge. (a) Bearings (b)coupling bolts © coupling rubber bush (d)split casing gaskets (e)shaft sleeves (f) replacing the air cocks grease nipple etc (g) painting the pump & Motor with one coat synthetic enamel grey colour paint (Fire Pump House No 1 & 2).

M&L for repairs and servicing of Jocky pump & Motor Set (Make M/s Crompton Greaves) electric driven Squirrel cage induction motor 3 phase 415 V AC 50HZ opening & cleaning inside of 15 HP motor stator varnishing and drying ,re-winding and duly replacing the following worn out parts of pump and re -erecting, testing and commissioning complete all as specified and directed by Engr-in-Charge. (a) Bearings (b)coupling bolts © coupling rubber bush (d)split casing gaskets (e)shaft sleeves (f) replacing the air cocks grease nipple etc (g) painting the pump & Motor with one coat synthetic enamel grey colour paint. (Fire Pump House No1 & 2)

S&F PVC insulated submersible cable 03 core 1100 Volt AC Supply stranded copper conductor of size 10 sqmm in replacement of old U/S cable, complete all as specified and directed by Engr-in-Charge.

S&F PVC insulated submersible cable 03 core 1100 Volt AC Supply stranded copper conductor of size 16 sqmm in replacement of old U/S cable, complete all as specified and directed by Engr-in-Charge.

S&F in replacment of gun metal globe or gate valve with iron wheel head screwed both ends suitable for galvanised pipe 20 mm bore complete all as specified and directed by Engr-in-Charge.

All as per item Srl No 28 above here in before but 25 mm bore

All as per item Srl No 28 abovehere in before but 40 mm bore

All as per item Srl No 28 above here in before but 50 mm bore

S&F in replacment of GI union on existing water supply line suitable for galvanised pipe 20 mm bore complete all as specified and directed by Engr-in-Charge.

All as per item Srl No 32 above here in before but 25 mm bore

All as per item Srl No 32 above here in before but 40 mm bore

All as per item Srl No 32 above here in before but 50 mm bore

S&F GI coloumn pipe 100mm dia heavy duty 'C' class with flanged ends drill 3 meter including joining to exising main pipe line complete all as specified and directed by Engr-in-Charge. Note:- The cost of nuts bolts washers packing materials and pressure gauge shall be deemed to include in unit rate quoted by the contractor.

S&F in replacement of old unserviceable water level indicator cum auto motor shutdown devies electronic type including PVC copper cable 2.5 Sqmm with GI steel for hanging and water level censor 04-05 Nos with copper PVC cable as required as per site complete all as specified and directed by Engr-in-Charge.

S&F in replacement cast iron fitting such as bends, tapers, (any type, radius and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc.)Tee pieces single branch. "Y" junction, double branch, cross (all sockets or socket and spigot) collars, caps and plugs tee pieces, single branch for spigot and socket and flanged pipe up to 150 mm bore complete all as specified and directed by Engr-in-Charge.

S&F in replacement cast iron pipe 150 mm bore centrifugally cast class 'A' flanged both end in any length complete all as specified and directed by Engr-in-Charge.

S&F in replacement cast iron pipe 100 mm bore centrifugally cast class 'A' flanged both end in any length complete all as specified and directed by Engr-in-Charge.

M&L for lead joint suitable for CI pipe 80 mm bore complete for laying of new pipe line including rectification of leakage pipe line on daily, complete all as specified and directed by Engr-in-Charge.

M&L for lead joint suitable for CI pipe 100 mm bore complete for laying of new pipe line including rectification of leakage pipe line on daily complete all as specified and directed by Engr-in-Charge.

M&L for lead joint suitable for CI pipe 150 mm bore complete for laying of new pipe line including rectification of leakage pipe line on daily complete all as specified and directed by Engr-in-Charge.

S&F in replacment cast iron sluice valve 80 mm bore with flanged ends, with Gun metal spindle, CI gate with brass ring and iron wheel handle with jointing material such as nuts /bolts washers and rubber insertion sheet etc including taking out old U/S sluice valve complete all as specified and directed by Engr-in-Charge.

All as per srl item No 44 here in before but 100 mm dia.

All as per ser item No 44 above here in before but 150 mm bore

M &L for earth work in trenches / pit and bailing out water to rectfying leaking joint of CI pipe spigot and socket type 80 mm bore including pouring extra lead chieseling and levelling the excavated material after rectifying the leakage complete all as specified and directed by Engr-in-Charge.

All as per item ser No 47 above here in before but 100 mm bore

All as per item ser No 47 above here in before but 150 mm bore

S&F in replacment cast iron Non Return Valve 80 mm bore with flanged ends, with jointing material such as nuts /bolts washers and rubber insertion sheet etc including taking out old U/S Non Return Valve complete all as specified and directed by Engr-in-Charge.

All as per item ser No 50 above here in before but 100 mm bore

M&L for replacment existing cast iron double air release valve of size 50 mm bore replacment of worn out bolts, nuts gaskets if any complete all as specified and directed by Engr-in-Charge.

Taking down old u/s star delta starter Panel and Supply , install, testing and commissioning of fully automatic star delta starter Panel with all accessories in sheet steel enclosuer, 3 phase 440 volt, 50 Hz ,suitable for 25 HP submersible motor including incoming /outgoing cable connections and fixing arrangment, mounting on floor with suitable size of angle iron frame and legs complete all as specified and directed by Engr-in-Charge.

M&L for repair to existing valve pits of internal dimensions 90cm x 90 cm x 90 cm making good disturbed/dismantled brick work in cement mortar (1:4) plastering surfaces in CM 1:6, 15mm thick and PCC coping in cement concrete 1:2:4 type B-1 and providing MS cover in replacement made out of MS sheet 3 mm thick duly welded to MS angle iron frame 35x35x5mm including frame work as per existing size with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engr-in-Charge.

All as per ser item No 54 above here in before but size 75 x 75 x 75 cms

M&L for cleaning & flushing of RCC over head reservoir of capacity 25000 gallons at 60 feet staging removing of silt and sludge etc deposited inside the tank and cleaning of entire internal surfaces of tank with bleaching powder incl flushing with water, writing the capacity of tank and date of cleaning with black and white paint, size of text complete all as specified and directed by Engr-in-Charge.

All as per item item No 56 here in before but reservoir of capacity 4000 gallons at 14 feet staging.

M&L for cleaning & flushing of Static water tank cuboid/circular in shape of capacity 50000 gallons and the depth of 5 feet , and removing of silt and sludge etc deposited inside the tank and cleaning of entire internal surfaces of tank with bleaching powder incl flushing with water, writing the capacity of tank and date of cleaning with black and white paint, size of text complete all as specified and directed by Engr-in-Charge.

All as per item No 58 here in before but SWT of capacity 15000 gallons and the depth of 4.5 feet, complete all as specified and directed by Engr-in-Charge.

S&F phase sequancer corrector with phase loss corrector system working on 415 Volt, 50 Hz, On/Off coil (switch) current capacity 20A, working voltage 12/24 Volt, Cut of voltage (Low) 330-370 (Adjustable), cut of voltage (High) 440-540 Voltage (Adjustable), Phase reversal System, Single phasing protection system, Time delay to start system 150 sec and Off switching time (two stop the system) for 10 HP submersible pump etc complete all as specified and directed by Engr-in-Charge.

All as per item No 60 here in before but current Capacity 40A, 25HP

All as per item No 60 here in before but cuurent Capacity 65A, 45HP

Taking down old u/s bleching dozing pump along with all accessories and Supply and install connecing. Testing and commissioning of High Pressuure single Head adjustable "AQUAFIT" Dosing system Model No VST 1005 and VST 1006 of the following specification. Adjustble High Pressure 5 Kg/Sq. cm. power input 230V, 50 Hz, 40 SPM 1/30 fractional Horsepower, Max output 10 Ltr with mandatory accessories like lead Tubing, connecting ferrules, check valves, etc (A) Preparation tank Model No VST 1005 of net capacity 100 Ltr, FRP dosing tank dia 650 x net Height 375 + conical 300. Gross height with stand 1000 mm consisting of : (i) Water inlet line (ii) Outlet with stainer (iii) Drain (iv) overflow (v) conical bottom for sludge depositing (vi) Pot hole with cover (vii) level gauge (viii) Agitator 120 watt 900 RPM single phase flange mounted motor with plastic shaft and impeller. (B) Service Tank Model No VST 1006 dia 480 x height 575 net capacity 100 Ltr consisting of (i) water inlet line (ii) Dosing pump inlet arrangement (iii) Drain (iv) Overflow (v) Level Gauge (vi) inspection port (vii) Agitator 120 watt 900 RPM Single Phase flange mounted moto with plastic shaft and impeller (ix) provision of mounting Pump on Lid/wall Make : VARIMA of equivalent CG.

Attending complaints by deploying sufficient labour (Skilled and helpers) for repair to leakage/blockage of wall/ underground water carrying CI/DI pipes of sizes ,80mm to 150 mm bore of any description at any location including necessary excavation & earth work, cutting existing pipe lines, dewatering etc complete all as specified and directed by Engr-in-Charge. Note:- (i) Complaint shall be notified to contractor on telephone, therefore it is mandatory for the contractor to mention his ‘Mobile Number’ while quoting the tender. (ii) Complaint shall be notified to contractor at any time between 0600 hrs to 2000 hrs and the same shall be immediately attended and defects rectified within six hrs from notification of complaint to the contractor. (iii) Confirmation of attendance & rectification of complaint shall be given in writing by the contractor and same shall be recorded in the ‘Register’ maintained for the purpose. The ‘Register’ shall be produced to this office along with RAR/Final Bill. (iv) In case the contractor fails to attend complaints within stipulated time (i.e. 6 hrs), a penalty shall be imposed @ Rs 300/- per complaint. (iv) Rates quoted by the contractor shall be deemed included the cost of necessary T& P required. (v) CI/DI Pipes, Fittings and cost of jointing shall be measured and paid separately under respective items.

Attending complaints by deploying sufficient labour (Skilled and helpers) for repair to leakage/blockage of wall/underground water carrying GI pipes of sizes ,20mm to 50 mm bore of any description at any location including necessary excavation & earth work, cutting existing pipe lines, dewatering etc complete all as specified and directed by Engr-in-Charge. Note:- (i) Complaint shall be notified to contractor on telephone, therefore it is mandatory for the contractor to mention his ‘Mobile Number’ while quoting the tender. (ii) Complaint shall be notified to contractor at any time between 0600 hrs to 2000 hrs and the same shall be immediately attended and defects rectified within six hrs from notification of complaint to the contractor. (iii) Confirmation of attendance & rectification of complaint shall be given in writing by the contractor and same shall be recorded in the ‘Register’ maintained for the purpose. The ‘Register’ shall be produced to this office along with RAR/Final Bill. (iv) In case the contractor fails to attend complaints within stipulated time (i.e. 6 hrs), a penalty shall be imposed @ Rs 300/- per complaint. (iv) Rates quoted by the contractor shall be deemed included the cost of necessary fittings and T& P required. (v) GI Pipes shall be measured and paid separately under respective items.

S&F bettery 12 volts 180AH, complete all as specified and directed by Engr-in-Charge.

M&L for replacement on load change over rotery type 4 pole 415 volt 200 Amp, complete all as specified and directed by Engr-in-Charge.

Supply only orthotolidine reagenet for chlorine test in 500 ml bottle of, complete all as specified and directed by Engr-in-Charge.

S&F in replacement MCCB 400 Amp 4 pole 36 KA 415 Volt complete all as specified and directed by Engr-in-Charge.

S&F in replacement MCCB 200 Amp 4 pole 36 KA 415 Volt complete all as specified and directed by Engr-in-Charge.

S&F in replacement MCCB 160 Amp 4 pole 36 KA 415 Volt complete all as specified and directed by Engr-in-Charge.

S&F in replacement MCCB 250 Amp 4 pole 36 KA 415 Volt complete all as specified and directed by Engr-in-Charge.

S&F aviation light LED type fixed on the top of OHT of any height including necessary fixing accessories complete all as specified and directed by Engr-in-Charge.

M&L and services for taking sample water in sterlised bottles from various borewells for Analysis of water for the following parameters and obtaining sample test report from Govt Recognized Laboratories: (i) Physio Chemical Analysis of Water ( Colour , odour , pH Total solids, Dissolved Solids, Permanent hardness, temporary Hardness, Ammonia feree and salinbe, Ammonia Albuminoidal, Nitrites, Nitreates, Oxygen absorption at 15 Min, Iron , Fluoride) (ii) Microbiological Analysis ( Totral Choliforms , Eschirrchea Coli) Note:- 1. A certificate of approval / certification of Lab by Goivt Of India / State Govt shall be submitted by the contractor to the deptt. 2. Sample shall be submitted to the Labortory within 24 Hrs of collection of sample.

Supply of Chlorine test kit with coloured ample complete with all testing fitments and OT solution in Rexene finish Box, complete all as specified and directed by Engr-in-Charge. Note:- Test kit shall be of standred quality.

Disconnect the electrical connection and water pipe connection of motor pump and taking out the motor pump from bore well and column pipe of 3 mtr long -10 nos with required T &P for carrying out the following works complete all as specified and directed by Engr-in-Charge:-

Developing the borewell for six hours with air compressor machine of capacity 250 PSI and 550 Cfm till clear water is obtain from the borewell and all the blocked stainers are opened upto depth of 300 feet complete all as specified and directed by Engr-in-Charge.

Lowering of submersible pump set with column pipe of 80/100 mm dia 3 mtr long -10 Nos with required T & P and man power, complete all as specified and directed by Engr-in-Charge.

S&F pea gravel of size 3 to 10 mm to a packed thickness into the side of existing bore well (which is hollow space between casing pipe and true bore) complete all as specified and directed by Engr-in-Charge.

S&F Ammeter,square type, 0-200 Amps, complete all as specified and directed by Engr-in-Charge.

All as per item No 80 above but 0-100 amps, complete all as specified and directed by Engr-in-Charge.

All as per item No 80 above but 0-60 amps, complete all as specified and directed by Engr-in-Charge.

S&F volt meter,square type ,0-500 volts, complete all as specified and directed by Engr-in-Charge.

Supply only gland packing of size 10 mm to 16mm, complete all as specified and directed by Engr-in-Charge.

M&L for replacment of pressure gauge 0-100 PSI, dial type fixed on pumping line in various pumps complete all as specified and directed by Engr-in-Charge.

Relaying of disconnected CI/DI pipe 80 to 150 mm bore dismantled including transporting to the new location as directed not more than 500 mtr distance, complete all as specified and directed by Engr-in-Charge of the 350 mm sizes. Note:- Jointing, fittings & earth work will be measured and paid separately.

S&F MS clamp of size 50x6 mm, MS flat iron with one No GI/MS socket of 20mm/15mm duly welded incl nut & bolts for taking branch connection/jointing of branch connection from 40 to 150mm bore line including boring in GI/CI pipe incl rubber packing, complete all as specified and directed by Engr-in-Charge.

M&L for painting of CI/GI pipe 80 mm to 150mm dia laid in open surface/wall with 2 coat of super enamelled black paint after cleaning, brushing the existing surface of pipe at Pump houses in various location of Beas and Jandiala complete all as specified and directed by Engr-in-Charge.

Supply laying, commissioning and testing XLPE insulated armoured heavy duty, electric cable with aluminium stranded conductor for working 1100 Voltage grade size 35 sqmm 3.5 Core including taking out existing unserviceable cable complete all as specified and directed by Engr-in-Charge. Note:- Earth work, sand cushioning and brick protection shall be measured and paid for separetaly.

All as per item No 89 above here in before but size 3.5 core 70 Sqmm, complete all as specified and directed by Engr-in-Charge.

All as per item No 89 above here in before but size 3.5 core 95 Sqmm, complete all as specified and directed by Engr-in-Charge.

All as per item No 89 above here in before but size 3.5 core 120 Sqmm, complete all as specified and directed by Engr-in-Charge.

Taking down existing old unsv LT panel & Supply, install, testing and commissioning of LT distribution panel, CPRI approved, weather/vermin proof, made out of 3 mm thick CRCA sheet, factory assembled cubicle pattern modular and compartmentalized construction, outdoor type, with front and backside hinged double door with locking arrangement, floor mounted free standing type, duly powder coated, 3 phase and neutral 630 amps current carrying capacity aluminium bus bar with epoxy insulated coating with colour code and insulated support with aluminium earth bus of size 25x3mm with terminal switch, cable galleries, inter connecting bus bar connection/linkage, complete with the following switch gears and mounting the panel board on ground with PCC (1:2:4) type B-1 using 20mm graded stone aggregate bedding upto a height of 45 cm above gorund level, complete all as specified and directed by Engr-in-Charge and comprising the following :- (a) MCCB 4 Pole, 415 V, Adjustable type, 400 Amps with breaking capacity 36 KA- 01 No (In Coming). (b) MCCB 4 Pole, 415 V, Adjustable type, 250 Amps with breaking capacity 36 KA- 02 No (out Going) (c) MCCB 4 Pole, 415 V, Adjustable type, 200 Amps with breaking capacity 36 KA- 02 Nos ( Out going) (d) MCCB 4 Pole, 415 V,Adjustable type, 100 Amps with breaking capacity 36 KA- 04 ( Out going) (e) Digital Volt Meter 0-500V - 01 No. (f) Digital Ampere Meter 0-500 A with 3 Nos of CTs. (g) Indicator LED type

Taking down existing old unsv Star Delta starter panel & Supply, install, testing and commissioning of Star Delta starter panel , (not less than 180cm x 150cm x 40cm ), CPRI approved, weather/vermin proof, made out of 2 mm thick CRCA sheet, factory assembled cubical pattern modular and compartmentalized construction, outdoor type, with front and backside hinged double door with locking arrangement, floor mounted free standing type, duly powder coated, 3 phase and neutral 400 amps current carrying capacity aluminium bus bar with epoxy insulated coating with colour code and insulated support with aluminium earth bus of size 25x3mm with terminal switch, cable galleries, inter connecting bus bar connection/linkage,prewired complete and mounting the panel board on ground with PCC (1:2:4) type B-1 using 20mm graded stone aggregate bedding upto a height of 45 cm above gorund level, complete all as specified and directed by Engr-in-Charge and comprising the following :- (i) Coper bus bar 400 Amps capacitor of suitable length insulated heavy heat shrinkable sleeves etc -04 No. (ii) MCCB 250 Amps FP, 415 Volt 35 KA adjustable thermal & adjustable magnetic stting Ics = 100% Icu -01 No(incommer) (iii) Star Delta Starter suitable for 100 HP motor , enclosures cubical of suitble size to operate on 3 Phase 4 wire system 415 Volts, 50 HZ, with sufficient numbers of circular cable entery holes, prewired - 02 Nos, and with each Star Delta Starter comprising of , MCCB 200 Amps 3P, 415 Volt 35 KA adjustable thermal & adjustable magnetic stting Ics = 100% Icu -01 No , Power contractor 3 pole 200 Amp (AC 3 duty) AC control different level of power and control contacts, inbuilt 1 No + 1 NC auxillary contacts -03 Nos, Thermal overload relay suitable for 100 HP motor, 3 Ph, 415 V - 01 No complete.

DUGGAL CONSTRUCTION CO