Provision of modifications to Officers Transit Facility No. 4 at RCI, Hyderabad

Amount

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.

In cement mortar

Dismantling of cement concrete platform along with curtain walls and base concrete etc. including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead :

120 x 120 cm (outside to outside)

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead:

Of area 3 sq. metres and below

Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in- Charge.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

All types of Soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All works upto plinth level.

1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Supply of approved earth obtained from outside MoD land and filling in trenches, plinth, sides of foundations, traverse etc., in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m(payment shall be made for the consolidated thickness only after deducting 5% for voids)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering,shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. Note:- Cement content considered in this item is @ 330 kg/cum. “Excess/ less cement used as per design mix is payable/recoverable separately).

All works upto plinth level.

All works above plinth level upto floor V level.

Centering and shuttering including strutting, propping etc. and removal of form for:

Foundations, footings, bases for columns

Columns, Pillars, Piers, Abutments, Posts and Struts

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with:

Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and laying autoclaved aerated cement blocks masonry with 230 mm thick AAC blocks in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

18 mm thick cement plaster in two coats with an under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Fixed to steel windows by welding

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :(Aldrops)

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Twin rubber stopper

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion: Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (fittings shall be paid for separately). Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 4.0 mm thickness

Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer - in - charge complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade:

New work (two or more coats) over and including water thinnable priming coat with cement primer.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade:

New work (two or more coats) over and including water thinnable priming coat with cement primer and 1mm thick putty.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.

Size of Tile 600x600 mm

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc, complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills,facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Granite of any colour and shade (Area of slab over 0.50 sqm)

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.

GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm,and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.

12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming to IS: 2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC ( Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing.

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle thresholdof mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge Profile B.

Fixing with adjustable lugs with split end tail to each jamb

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of crosssection 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.

30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:

W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:

White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:

White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing CP Brass towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 170 gms.

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required:

Single half stall urinal with 5 litre P.V.C. automatic flushing cistern

Providing and fixing CP brass bib cock of approved quality :15 mm nominal bore

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer-in- charge.

Providing and Fixing of CP Brass Bottle trap for wash basin and sink. Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms of make - Jaquar, Cat No. ALD-769L250X190 or such equivalent of Hindware & Paryware.

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.

Granite Stone of approved shade

Providing and fixing 600x450mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing CP Brass liquid soap container 109 mm wide, 125mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Flexible pipe (32 mm dia)

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors:

100 mm inlet and 75 mm outlet(Sand cast iron S&S as per IS - 3989)

Providing and fixing toilet paper holder:C.P. brass.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

15 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item

Credit of Steel work

Credit of flush doors

Credit of bib taps/ Stop cocks

Credit of PVC flush tanks

Credit of sintex tanks

Credit for electrical wiring

Credit for electrical MS boxes

Credit for electrical Fans

Credit for electrical Light Fixtures

Supply, installation, Testing and Commissioning of 3 phase and Neutral 415V, 4 wire , Free Standing Floor mounted MV Panel made out of 14 SWG MS sheet after seven tank process and painting with Epoxy powder coating. The panel shall consist of suitable rating TPN Aluminium busbar supported with DMC/ SMC barriers and color coded with Heat shrinkable sleeves. The Metering shall be provided as specified. The panel shall have Short circuit withstanding capacity of minimum 50 KA and consist of the switchgear as mentioned below. The panel shall be got fabricated from manufacturers with CPRI Test certificate only. . The size of all Panel Mounting Meters shall be 96X96mm. The Panels shall be mounted on 75MM U channels including supply and fixing of the same. Every MCCB shall be provided with ON/OFF/TRIP, Indication lamps of LED type. The Panel is to be installed in Indoor.

Supply, laying and commissioning of following size 1.1KVgrade XLPE PVC insulated armoured Aluminium conductor cable, neatly dressed & clamped to existing cable trays/Trench. (Make ; Polycab)

3.5CX120 SQMM XLPE AL.AR.CABLE

4CX16 SQMM PVC CU.AR.CABLE

3CX2.5 SQMM PVC CU.AR.CABLE

Providing Indoor ordinary end terminations for the cable specified above with compression type steel gland,Bi-metallic lugs using crimping tool,Insulation tape, Identification tags etc., including end termination and Earthing of Gland with 8SWG 'GI Wire

3.5CX120 SQMM XLPE AL.AR.CABLE

4CX16 SQMM PVC CU.AR.CABLE

3CX2.5 SQMM PVC CU.AR.CABLE

Supply and Installation of following size 2mm thick GI Perforated type cable tray with coupler plates, bends, elbows, tees etc as required. The scope also includes suitable cable tray supports arrangements on walls/ Ceiling/ Trench with M.S.Structrual steel/ Threaded rods, anchor bolts & nuts wherever required as per site conditions.

300 mm wide x 50 mm deep x 1.6 mm thick

200 mm wide x 50 mm deep x 1.6 mm thick

100 mm wide x 50 mm deep x 1.6 mm thick

Providing G.I. Earth station, with 40mm dia 2500mm long GI pipe including construction of brick pedestal, providing meshed funnel,CI cover and other civil Engineering works,spreading a homogenous mixture of salt, charcoal aroundthe pipe etc, completely as per IS 3043, 1987 or latest revision.

Supply and laying of following earth strips/ conductors.

Supply and fixing of 25 x 5 MM GI Flat

Supply and fixing of 1C x 6 Sqm PVC Insulated Flexible Copper Cable (Green)

Supply and Wiring with the following size heavy duty FRLS PVC conduit concealed in wall / ceiling/above false ceiling, including junction boxes, bends, elbows & fexible pipes

25 mm Dia

Supply and Installation of following type LED/CFL lights & Fans wall/ Ceiling including all fixing accessories such as leads,Teak wood round block etc complete as required.

36W LED Light Fixture (600x 600mm) (Bajaj Make: BCTBLR 36W ZTN NW)

15W LED Round Type Light Fixture (Bajaj Make: BZSLO 15W NW PRO)

40W T5 Tube Lights (Bajaj Make: BCLAB 40W)

10W Bracket Lights LED

2W LED spot Lights (Bajaj Make: BRDCSL 6W NW)

300mm metalic blade Exhaust Fan (HavellsMake:Ventil Air - DSP)

Point Wiring for Light with 2runs of 1.1 kV grade FRLS PVC 1.5 Sq.mm & 1 run of 1 Sq.mm multi strand Copper wires, run in and including anodised GI Switch box with modular switchs and the box covered with front plate. along with labling

One light point controlled by one 6A switch (consider wiring length 3 meters)

Two lights point controlled by one 6A switch (consider wiring length 6 meters)

Two light point controlled by two wAy 6A switch (consider wiring length 3 meters)

One Fan controlled by one 6A switch 300w regulator. (consider wiring length 10 meters)

One Fan controlled by two way 6A switch with 300w regulator. (consider wiring length 10 meters)

One Exhasut Fan controlled by one 6A switch. (consider wiring length 10 meters)

Supply, erection, testing and commissioning of the following power sockets with Switch/MCB's and with Flush/wall/surface mounting with front plate, cover and fixing screws etc complete along with labling.

1 No. of 6/16Amps, 6-pin Single phase commercial type socket controlled by 1no.s of 16 Amps SP Switch (IP 44) .

Supply, erection, testing and commissioning of the following power sockets with Switch/MCB's and with Flush/wall/surface mounting with front plate , cover and fixing screws etc complete along with labling.

1 No. of 6/16Amps, 6-pin Single phase commercial type socket controlled by 1no.s of 16 Amps SP Switch(IP 44) . Wiring shall be measured separately under Item No: E-12

2 No. of 6/16Amps, 6-pin Single phase commercial type socket controlled by 1no.s of 16 Amps SP Switch(IP 44) . Wiring shall be measured separately under Item No: E-12

1 No. of 16Amps, 3-pin Single phase commercial type socket controlled by 1no.s of 16 Amps SP Switch(IP 44) . Wiring shall be measured separately under Item No: E-12

2 No. of 16Amps, 3-pin Single phase commercial type socket controlled by 2no.s of 16 Amps SP Switch(IP 44) . Wiring shall be measured separately under Item No: E-12

1 No. of 20Amps, 3-pin Single phase Industrial type socket controlled by 1no.s of 16 Amps SP MCB (IP 44) . Wiring shall be measured separately under Item No: E-12 ( for AC)

Supply and Wiring with the following size 1.1kV grade FRLS PVC insulated Copper conductor multi strand wires and terminated with suitable lugs.

2runs of 2.5Sq.mm wires with 1run of 1.5 Sq.mm wires in existing 25 mm dia conduit from DB to Switch Board.(Primary Wiring for lighting )

Supply and Wiring with the following size 1.1kV grade FRLS PVC insulated Copper conductor multi strand wires and terminated with suitable lugs.

2runs of 4Sq.mm wires with 1run of 2.5 Sq.mm wires in existing 25 mm dia conduit from DB to power socket & AC Sockets

Supply, Installation, Testing and commissioning of TPN Vertical/ Horizontal MCCB/MCB Distribution boards dust and vermin protected and rated for 415V Three Phase AC supply operation including incoming MCB as per specifications and required capacity MCB's shall conform to IS: 8828

4 Way TPN DB( Horizontal type)with 63A FP MCB with 100ma RCBO as incomer and 40A DP MCB foe Each Phase and 12 nos 32A SP MCBs s outgoings.

8 Way SPN DB( Horizontal type)with 32A DP RCBO as incomer and 2 nos 10A SP, 3 nos 16A SP, 1 no 20A SP MCBs s outgoings.

Supply and fixing of Telephone outlet (RJ11) with anodised GI box with front plate and plug in type telephone socket along with labling

Supply and laying 2 pair 0.5 sqmm of CAT5 dia PVC insulated Copper conductor Telephone cable conforming to latest Standards

Supply, Installation & commissioning of 30 Pair telephone krone box

Supply and laying 20 pair 0.5 sqmm of CAT5 dia PVC insulated Copper conductor Telephone cable conforming to latest Standards

Road including average excavation of 225mm in all types of soil, including 225mm thick average filling with approved earth wherever required, consolidation of the subgrade/ formation, laying of WMM 175mm consolidation thickness with graded stone aggregatesize( range 53 mm to 0.075 mm) , 50mm DBC surface course including 1.5m berms on either side of the road, consolidation with 8 to 10 MT road roller etc complete.

Hardstanding including excavation in all types of soil, filling with approved earth, consolidation of the subgrade formation, with a layer of 100 thick WBM and top layer of 75 thick WBM with 100mm thick layer of PCC 1:4:8 and 100mm thick PCC 1:2:4 on top finished smooth with chequred marking etc., all complete.

Providing storm water drains of size 450mm wide and an average depth of 600mm varries as per site conditions including earth work excavation / filling, PCC levelling courses, RR masonary walls, plastering/ pointing, PCC coping etc., complete.

Supply and laying of NP2 class hume pipes including necessary earth work excavation in all types of soil / rock, PCC bed concrete and encasing etc., complete all as specified of following sizes.

150mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.

15 mm nominal outer dia Pipes

25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

25 mm nominal bore

32 mm nominal bore.

SAI CONSTRUCTIONS

Hi-Tech Infrastructure