Const. of Residential School (PMJVK) Block Ramgarh Distt Alwar for Minority Department

Amount

Providing and Fixing Backstop unit (Basketball poles). There shall be two (2) backstop units, and each consisting of the following parts: • One (1) backboard. • One (1) basket ring with a ring mounting plate. • One (1) basket net. • One (1) basket support structure. • Padding etc. with following specifications The backboards shall be made of a suitable transparent material (of a tempered safety glass), made in one (1) piece, non reflective, with a flat front surface and shall: • Have a protective framework of the backboard support structure around the outer edge. • Be manufactured such that, if broken, the pieces of glass do not split off. The backboards shall measure 1,800 mm (+ a maximum of 30 mm) horizontally and 1,050 mm (+ a maximum of 20 mm) vertically. All lines on the backboards shall be: • In white, 50 mm in width. The borders of the backboards shall be marked with a boundary line and an additional rectangle behind the ring as follows: • Outside dimensions: 590 mm (+ a maximum of 20 mm) horizontally and 450 mm (+ a maximum of 8 mm) vertically. • The top edge of the base of the rectangle shall be level with the top of the ring and 150 mm (- 2 mm) above the bottom edge of the backboard. Basket ring: The rings shall be made of solid steel and shall: • Have an inside diameter of a minimum of 450 mm and a maximum of 459 mm. • Be painted orange within the following Natural Colour System (NCS) FIBA approved spectrum : 0080-Y70R 0090-Y70R 1080-Y70R • Have its metal a minimum of 16 mm and a maximum of 20 mm in diameter. The net shall be attached to each ring in 12 places. The fittings for the attachment shall: • Not have any sharp edges or gaps, • Have gaps smaller than 8 mm, to prevent fingers from entering, • Basket net. The nets shall be made of white cord and shall be: • Suspended from the rings. • Manufactured so that they check the ball momentarily as it passes through the basket. • No less than 400 mm and no more than 450 mm in length. • Manufactured with12 loops to attach it to the ring. The upper section of the net shall be semi-rigid to prevent: • The net from rebounding up through or over the ring, creating possible entanglement. The ball from becoming trapped in the net or rebounding back out of the net.

Padding: The backboard and backboard support structure must be padded. The padding shall be of a single solid colour and shall be the same colour on both backboards and support structures. The padding shall be 20 to 27 mm thick from the front, back and side surface of the backboards. The padding shall be 48 to 55 mm thick from the bottom edge of the backboards.The padding shall cover the bottom surface of each backboard and the side surface to a distance of 350 to 450 mm from the bottom. The front and back surface must be covered to a minimum distance of 20 to 25 mm from the bottom of each backboard. All padding shall: • Be constructed so as to prevent limbs from being trapped. • Have a maximum indentation factor of 50%. This means that when a force is applied suddenly to the padding, the indentation in the padding does not exceed 50% of its original thickness.

Providing & Fixing of double leaf steel shutter for cupboard, the frame is made of pressed steel ISI section 80x25 mm x 1.25 mm thick with 1.00 mm MS sheet to spot welded including holdfasts of 15x3mm, MS oxidized fittings such as butt hinges, sliding doors bolts, handles, tower bolts and twin peg etc complete including applying priming coat of approved steel primer of red oxide zinc chromate and spray painting in approved shade with deco paint of approved quality complete as per direction of Engineer in Charge.

Designing & construction one GWR 100 KL in RCC at construction of GWR (1.00 Lacs Litre) at Minority Department School Building Sahadoli Ramgarh Distt Alwar Consisting of RCC Footing wall dome including excavation in all type of strata, foundation concrete plinth protection, refilling & desposing of the surplus stuff all labour and material charge including providing, lowering, laying, erecting, hoisting and jointing of DI/DF pipe & assembly as inlet, outlet washout overflow and by pass arrangement as per design providing and fixing accessories such CI puddle collar, Bend, Sluice Valve, Foot Value on the pipe mouth up/down Aluminium ladder, Aluminium manhole frame and cover, water level indicator, lightening conductor, Ventilator providing and supplying three coats of cement paint to the external and internal parts of structure up to FSL and Bitumen apoxy paint above FSL including roof slab/dome and giving satisfactory water tightness test as per I.S. code.

The job to include painting the name of the scheme, slogans and other details on the reservoirs as per the directions of Engineer in Charge. Connecting Vertical stacks and testing & commissioning of whole system. Satisfactory water tightness test as per I.S. code. Including P&F Sluice Valve of Cast Iron ISI mark apporved make as required dia.

Bidder Name

Amount

LNA Infraprojects Pvt. Limited(GSTN-08AADCL1585B1ZQ)