Construction Work

Amount

Installation Charges inclusive of Transportation to site and the Bored pile equipment employed for the works including setting up of pile driving equipment with all accessories and tools at each of the pile location based on the sequence of operation approved by the departmental Engineers irrespective of the location and distance involved in movement of pile driving equipment etc., complete.

Installation of Vertical Bored cast in situ RCC piles in all types of soils, using Ready Mix Concrete of M30 grade, with sulphate resistant Cement, fine aggregate, 20mm and down graded HBGS jelly coarse aggregate. The rate includes cost of reinforcing steel, binding wire, fabrication, welding charges, placing of reinforcement cage in bore hole in correct position, cost of boring to the required depth with Bentonite solution with temprory casing of required length, conveyance of RMC to site and pouring concrete using Tremine pipes, conveyance of all materials to the site including all tools and plants, shifting the plants and equipments from one point to another, excavation of mud pits for circulation of Bentonite solution, closing the mud pits to original level and mud removal with initial lead and lift but including dismandeling the concrete above the cut off level etc complete as directed by the departmental officers including socketing. The reinforcement cage should be welded properly for lifting. The concrete cubes to be tested as per IS 456-2000. Acceptance criteria by clause 16.1. Frequency of testing should be as per clause 15.2.2. The length of pile for payment shall be measured up to natural ground level. The work should be carried out as per IS 2911. Pile depth should be decided by the departmental office at site.

450mm dia pile - having longitudinal reinforcement of 4 Nos of 16# + 4Nos of 12# with helical reinforcement of 8# @ 200 mm c/c with inner rings of 12 mm dia @ 1000 mm c/c with lifting hook of 12 mm dia required depth.

600mm dia pile - having longitudinal reinforcement of 10 Nos of 20 # with helical reinforcement of 10# @ 200 mm c/c with inner rings of 12 mm dia @ 1000 mm c/c with lifting hook of 12 mm dia required depth.

Initial load test as per IS 2911 part IV 1995 including cost of single pile (250% of Pile capacity, labour, reinforcement charges and all other incidental charges including excavation, shoring, strutting, dewatering etc., as necessary hire charges for jacks, measuring devices, structural frames work for platform, kent ledges etc, as required and as directed by the departmental officers etc. complete.

Routine load test as per IS 2911 part IV 1995 (150% of pile capacity) including labour charges for jack, measuring devices, structural frame work plot form, kent ledges etc., as required and as directed by the departmental officers etc. complete.

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Supplying and filling in basement with Stone dust (Quarry dust) in layers of not more than 15 cm thick, well rammed watered and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and filling in foundation, basement, etc with filling M-sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Providing laying spreading and compacting grade stone aggregate to WET mix Macadam specication including premixing the meterial with water at OMC in mechical mix plant carriage of mixed material by tripper to site laying in uniform layers with pavers in sub base/base course on well prepared surface and compacting with vibratory roller to acheive the desired density etc., complete as per clause 406 morth rev - 5 specification

Cement Concrete 1:5:10 (One Cement, Five sand and Ten hard broken stone ielly) using 40 mm gauge hard broken granite stone ielly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Extra for vaccum dewatering in fresh concrete works 80 to 120mm thick by levelling with double framed screed vibrator finishing with power floatter and power trowel and indentical works etc., complete and as directed by the departmental officers.

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10x6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc.

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

For circular columns

Providing additional strutting to centering of RCC slabs of plain surface for every additional 1.0 metre height or part thereof but not less than 30 cm, over the initial 3.00 metre height from floor level using casurina props of 10cm to 13cm dia including cross bracing etc., complete complying with standard specification and as directed by the department officers.

Providing and laying in position, Standardised Concrete Mix M-35 Grade in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 440 kg/mᶾ and maximum water cement ratio of 0.40, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5136 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m.) 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

For Stilt floor

For First floor

For Second floor

For Third floor

Providing and laying in position, Standardised Concrete Mix M-30 Grade in accordance with IS:456-2000,using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 400 kglms and maximum water cement ratio of 0.45, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

Foundation and Basement

For Stilt floor

For First floor

For Second floor

For Third floor

For Fourth floor

Providing and laying in position, Standardised Concrete Mix M-20 Grade in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/mᶾ and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m.) 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

Foundation and Basement

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Post Tensioning Work: Design and execution of post tensioning work, including decoiling, the strands, cutting to the required lengths, supplying, laying of HT strands sheathing (GI corrugated ducts 0.3mm thick) jointing with couplers and inserting the strands, profiling, fixing liveend anchorages, including supply of stressing anchorages, suitable for 5-5 & 5-4 tendons, grout vents, making dead end anchorages, including flowering the strands, fixing tendon support bars, supervising the fixing of antibursting reinforcement, stressing the cables, end trimming, grouting the cables, with cement slurry, mixed with admixtures with required tools, plants, and machineries, and consumables etc. (Shuttering, concreting & reinforcement steel shall be paid under respective items) at all heights including all leads, lifts, coordination, with the post- tensioning agency, preparation of drawings, obtaining approval from the Employer / Architect etc. Rate to include providing water, power, cement and admixture for grouting, packing of sheathing and anchorages blockings, filling of recess pockets after stressing using grouts (cement slurry mixed with approved admixtures) including providing access to post tensioning at all heights including all leads, lifts etc., all complete and as approved and as directed by the Employer Architect but excluding shuttering, concreting & reinforcement steel which shall be payable under respective items separately.

Brick work in Cement Mortar 1:5 (One cement and six sand) using Fly Ash Bricks of 230 x 110 x 70mm size conforming to IS: 12894-1989 Class designation not less 50 kg./ sq.cm. average compressive strength in cement mortar 1:5 for load bearing structures for foundation and basement and for superstructure including curing, etc., complete complying with standard specifiction.

In basement and foundation

Brick work in Cement Mortar 1:6 (One cement and six sand) using Fly Ash Bricks of 230 x 110 x 70mm size conforming to IS: 12894-1989 Class designation not less 50 kg./ sq.cm. average compressive strength in cement mortar 1:6 for load bearing structures for foundation and basement and for superstructure including curing, etc., complete complying with standard specifiction.

In Stilt floor

In First floor

In Second floor

In Third floor

In Fourth floor

Brick partition walls of 11cm thickness using Fly Ash Bricks of 230 x 110 x 70mm size in Cement Mortar 1:3 (One Cement and Three Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

In First floor

In Second floor

In Third floor

Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick mixed with Bonding agent Cebex112, Zydex -Zycrete 2X or other Equalent compound conforming to BIS at 200ml of One cement bag (50kg) for increased workability and air entrainment used finishing in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Sand) 10mm thick mixed with Bonding agent Cebex112, Zydex -Zycrete 2X or other Equalent compound conforming to BIS at 200ml of One cement bag (50kg) for increased workability and air entrainment used finishing including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Paving the floor with best quality Double Charged Vitrified Tiles 800x800x10mm of approved colour, shade andquality laid in cement mortar 1:3 (one cement and three sand)20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be Johnson / Kajaria / Somany / Nitco / RAK which has to be gotapproved by Executive Engineer before use on works)

Flooring with Self design Joint free rectified Ceramic Tiles of size 305 x 305 x 8mm laid over 20mm thick cement mortar 1:3 (Onecement and Tree sand) base mortar over the existing slab / floorincluding cutting the tiles to the required size with special cutterwherever necessary, laying in positionand and pointing with whitecement mixed with colouring pigment at the rate of 0.3 kg. / sq.m.etc., complete complying with standard specification.(The makeand brand of the tiles should be Johnson / Kajaria / Somany / Nitco/ RAK or Equivalent which has to be got approved by executive Engineer before use on works)

Dadooing walls with Joint free rectified Colour designed digital print ceramic tiles, with borders, with size of 3OOmm x 600mm x 10mm and above setin Cement Mortar 1:2 (One Cement and Two sand) 20mm thick andpointing the joints with white cement mixed with colouring pigmentsat the rate of 0.40 Kg. / sq.m. nbatly in all floors, curing, etc,,complying with standard specification and as directed by thedepartmental officers. (The make and brand of the tiles should belike Johnson / Kajaria / Somany / Nitco / RAK or Equivalent whichhas to be got approved by Executive Engineer before use on works)

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Clading the walls by supplying and fixing of White Galaxy or equivalent quality of granite vertical slab for an average thickness of 17 mm to 20mm for vertical surface over a base layer in cement mortar 1:2 10 mm thick and pointing with the same mortar as directed and agmi,Aroldate and POP Paste for fixing the granite slab in position wherever necessary. The quality and colour of granite slab should be got approved by the Executive Engineer before use on works

Clading the walls by supplying and fixing of jet black or equivalent quality of granite vertical slab for an average thickness of 17 mm to 20mm for vertical surface over a base layer in cement mortar 1:2 10 mm thick and pointing with the same mortar as directed and agmi,Aroldate and POP Paste for fixing the granite slab in position wherever necessary. The quality and colour of granite slab should be got approved by the Executive Engineer before use on works

Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing grooving to granite slab at the intermediate edges of the vertical face with neat finishing etc complete with standard specification and as directed by the departmental officers. The cost including higher charges of machines and labour charges etc complete

Providing double semi nosing to granite slab at the edges of the vertical space with neat finishing etc complete with standard specification and as directed by the departmental officers. The cost including higher charges of machines and labour charges etc complete

Providing and Fixing of PVC Trims (Corner beeding) at the outer corner profiles of the tiles including cost of material, labour and handling etc. as directed by departmental engineers at site of work and as per standard specification.

Supplying 18 to 20 mm thick white jet blck granite partition slab for urinals of 1200x600(Avg) mm size fixing to wall using 3Nos. of suitable chromium plated brackets with CP bolt and nets, washers, cutting to required shape polishing to all the expose and surfaces and edge grinding etc; complete as directed by the dept officers.

Supplying and applying Putty with two coats of plastered wall surface of first class quality and of approved including thorough scrapping, clean removal of dirt wherever required etc., complete complying with standard specification.

Supplying and applying of two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothly with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The surface shall then be allowed to dry for atleast 48 hours. It shall then be sand papered (waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then sand papering (water proof abrasive sheet) the same after it is dry and finishing the surface smoothly,etc.,complete complying with standard specifications and as directed by the Departmental Officers.The rates are inclusive of hire charges for grinding machine with wheel, cost of sand paper (water proof abrasive sheet), cost of putty blade, labour charges for grinding the joints and sand papering, two coats of putty, scrapping the putty area to level the surface smooth, etc.,complete. The putty should be got approved by the Executive Engineer before

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Providing the texture finish to the newly plastered wall with ready made texture putty with patterns at all levels including the cost of coating, labour charges and other incidental charges etc., complete as directed by the departmental officers.

Providing Anti-termite treatment to soil adjecent and under building foundation, plinth periphery of the building by application of chemicals of IS 6313 Part I to IV in stages to suit the progress of work consist as per the detailed specification as below. (Measurements taken for the plinth area for the purpose of payment) including breaking of termite mounds, making holes with crow bar, closing the holes after the treatment and including cost of chemicals, labour charges, transport and storing, etc., complete and as directed by the departmental officers. (The chemical should be got approved by Executive Engineer before use on work).

Providing, mixing, laying polymer based water proofing treatment for the Sunken Toilet / Lift well/ OHT Rcc wall by applying cement based, flexible, waterproofing compound confirming to IS:2645, to a thickness of 1mm of the prepared surface of the roof slab / floor slab as per specifications mentioned above providing cement mortar 1:3, water proofing cover plaster to a thickness of 12mm over the membrane coating with admixture of approved make. Rate quoted is inclusive of preparation of surface, which includes cleaning of surface polymer mortar curing, labour, tools and equipment, etc. Rate inclusive of grouting with cement and sand required for the treatment, the cost and labour charges for fixing 25mm dia pressure pipes 15kg/cSq.m to a length of 45cm for drip pipes, etc. complete.

Brick Jelly Lime Concrete of 1:2:5 (One Lime,Two Sand and Five Brick jelly ) with 40 mm hand broken brick jelly for Sunken portions including dewatering wherever necessary and laid in layers of not more than 15cm thick, well rammed, consolidated and curing etc. complete complying with standard specification.

Laying of screed concrete using Cement concrete mix 1:2:4 ( one cement, two sand and four hard broken stone jelly) using HBGS 6-10mm ISS metal for wearing coat including laying, compacting, finishing and curing etc., complete as per standard specification and as directed by the departmental officers

Paving the top of roof with solar reflective ceramic tiles (required design) of 305x 305x 7mm thick of approved quality and colour laid in cement mortar 1:3 (One cement and three sand) 20mm thick and pointed with tile grout (Nitotile Grout or equivalent) and cement in the ratio of 1:3 for joint ,curing etc., complete complying with the standard specification and as directed by the departmental officers. (The make and brand of the tiles (Johnson endura or equivalent) should be got approved by the Executive Engineer before use on works)

Supplying and fixing Teak Wood frames for doors Windows and Ventilators using required MS angles, flats and rods of approved design and as directed by the departmental officers including cost of MS Grills, labour charges and cost of one coat of red oxide primer with labour charges for priming coat etc. complete complying with standard specifiction.

T.W Scantlings Upto 2m

T.W Scantlings above 2m below 3m

Supplying, hold fast of M.S flats of over all size of 330x50x6mm suitably folded to the required L shape have two end of lap of 50mm long each and overall length of the horizontal portion as 230mm & including making necessary grooves in two end laps to accomadate screws etc., complete.

Supplying and fixing in position of flush shutter with teak wood vener for doors of 35 mm thick block board core with of applied shade and hot pressed bonded with liquid phenol formaldluide resin with internal lifting with TW as per IS 2201/ part I /1991 The rates inludes the labour charges for fixing the shutter to the frames and for fixing furniture fiitings.The rate include the cost of furniture fittings etc complete

Single leaf

Double leaf

Supplying and fixing in position of Teak wood door shutter using spl quality teak wood planks of 40mm thick panelled doors with required raw materials, Brass hinges, Brass tower bolt, ornamental Brass handles, Door stopper, Door closer, Brass aldrops and bush with suitable locking arrangements etc. The rate should be inclusive of cost of materials, labour charges for wrought and put up the doors with kadasal charges and transporting charges etc complete complying with standard specification and as directed by the Departmental officers.

Polishing the teakwood and wooden panelled door with best melamine varnish finishing including labour charges for scrapping the existing T.W panelled throughly on both sides of the door, sand papering without affecting the teakwood plank grooves and natural design with preparation of surface using sand paper and finishing the smooth wooden surface and applying of melamine polishing on the teakwood panelled door/ partition surface using spray machine on uniform layer of smooth surface formed without any air bubbles after finishing the work etc., the rate inclusive of cost of materials ,labour charges ,transportion charges, labour for scrapping charges, etc complete complying with standard specification and as directed by the departmental officer (the materials quality are approved by the EE Before use of work.

Supplying and Fixing of Wood Polymer Composite (WPC) door with solid door frames extruded with size 75mmx50mm. The Inner core made of rigid WPC compound with minimum shore hardness of 55, and Buld Density 750Kg/cub.Mt. The frame shall be fixed to the wall using 10x10mm long MS screw throught the frame by using PVC fasteners. A minimum of 4nos screww to be provided for each vertical members,Door shutter of 25mm thick Wood Polymer Composite (WPC) single core Extruded Door Shutter, with one side digital printing of Specified Design which is approved by engineer-In-Charge. Both side of the shutter shall have rough sugar texture finish, aminated with UV oil. The solid WPC board shall have minimum shore hardness of 55 and Bulk density 550Kg/Cub.Mt moulding the thickness remains 25mm(+/-1mm) etc complete as per the direction of the departmental officers.

Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish 1/3rd fixed glazing 2/3rd prelaminated board of Aluminium partition of size 2.70 mx 2.10 m.The outer frames Outer frame: 50x38x3mm@ 1.72 kg/m,Centre mullions: 63.50x38x3mm@ 1.55 kg/m,Alu. Clips: 17.27x17.15x1.50mm @ 0.175kg/mg/m for intermediate vertical mullion 90cm c/c. Horizontal mullion at 1.00m 2.10m covered with 4 mm thick plain glass with neccessary aluminium clips of size 17.27x17.15 x1.50mm @ 0.176kg/m and with required rubber beading etc., including necessary dismantling holes in RCC column,masonry wherever in necessary with power drills to the extent required and made good the damaged portion in good condition after fixing as directed by the departmental officers. All the aluminium sections should be anodised not less than 15 microns as ISI specification1868/1962 / and should be gotapproved by Executive Engineer before use.

Fabricating Supplying and fixing in position of Aluminium anodised Powder Coated of single leaf door with half panelled with 12mm thick both side laminated particle board at bottom and half glazed using 5.50mm thick Plain glass at top.The outer frame shall be with aluminium box section 101.60x44.45x3.18m at 2.319kg/m and Shutter frame made of section Vertical & Top rail: [email protected] kg/m and Bottom rail: 100x44.45x2.50mm@ 1.974 kg/m, Lock rail : 50x44.45x2.5mm @ 1.292 kg/m,Alu. Clips: 17.15x17.27x1.50mm @ 0.176 kg/m,Alu. Handle: 100x30mm @ 0.988 kg/m and necessary accessories such as aluminium clips, rubber beading, PVC felt, handle for a length of shutter (both sides), locking arrangements, furniture fittings such as aluminium tower bolts-250x12mm - 1 Nos., aluminium tower bolt 200x12mm - 1No., aluminium Hydraulic door closer - 1No ., lock-1No., Door stopper with rubber bushincluding cost of materials labour charges and power consumption charges required for fabrication including chipping, dismantling and making hole to the required extent in RCC column, beams, masonry with power drill wherever necessary and redoing the damaged portion to the original condition after fixing etc., complete. All the Alu. Section are to be anodised with matt finish under electricaly controlled conditions in accordance with IS 1868/1962 for an average anatic film thickness of 15 microns etc., complete.Aluminium sections,and furniture fittings shall be got approved by the Executive Engineer incharge.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Designing the Semi Unitised Structural Glazing System with open groove joint as per design intent, preparation of shop drawings for approval, supply, fabricate, erect as per approved shop drawings at all floor levels and all floor heights including conducting field test as per the test criteria set out in the particular specification (Metholodgy should be got approved by the Dept. Officials.) Design the framing system (i.e. male & Female frame) to support vision panels, spandrel panels either with glass or aluminium composite panel, openable, window panels on a continuous framing supported between floors. Also design the split framing unutilized glazing system in case of strip or punched windows with vision panel proposed with either insulated / Monolithic glass, groove width in the system both in horizontal and vertical shall not be more than 20mm. Glazing of panel shall be done only at factory at the controlled atmosphere

Supplying and Fixing Hydraulic Door Closer of various sizes of approved quality using Aluminium Extruded section body tubular type universal hydraulic door closer with double speed adjustment like HARDWYN 'GAZEL' (or) Equivalent (with ISI Monogram)

Supplying and fixing of M.S. grill of approved design for open courtyard, grill, grill work to doors and window openings etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including cutting the members, welding, grinding, one coat of priming coat using best approved quality red oxide primer, dismantling of walls / concrete if necessary, fixing and finishing the dismantled portion to original condition etc., complete complying with standard specification.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Providing and fixing 8mm thick fully designed perforated calcium silicate board 2'x2' panel tiled false ceiling (Hilux) including supplying and fixing true horizontal level false ceiling with 24mm prelude grid system Using hot dipped galvanisedsteel section exposed surface chemically cleaned caping prefinished in backed polyester paint wall angle of size 3000x19x 19mm used in the periphery of the ceiling fixed to the wall, parttion with the help of screws at 600mm c/c. Mainrunner of size 3000x24mm suspended at a 1200mm c/c by using securely fixed to the structural soffit of RCC slab by using 6mm Nylon Rwl plug at every 1200mm(max) and 1200mm long cross tee of size 1200x24mm to interlocked between mainrunner at 600mm c/c(max) to form a grid of size 1200x600mm.600mm long cross tee of size 600x24mm is inserted to form a grid of 600x600mm and finally laying classic lite regular edge tiles of size 600x600x15mm

Supplying and Installing Metal False Ceiling using Fire Retardant Galvanized Steel Sheet Plain lay in tile size 600mm x 600mm, 0.5mm thick, powder coated on external surface and shall have flange on all four sides to rest on the exposed grids. The system to give 600mm x 600mm centre to centre 'T'. The 'T' shall be not be dipped GI Tee Section 3600mm long main Tee. 24mm wide and cross Tee panels are formed by running main runner of 'T' section of size 30mm x 24mm powder coated at bottom at intervals with powder coating at bottom. Necessary provision of inter locking of 'T' section are made at required intervals not exceeding 1200mm. The main runners are suspended from the ceiling by means of 4mm dia. GI rods fixed to the ceiling using anchor fasteners of 50mm x 8mm size with nylon inset and hooked to the main rubbers using clips. The last hangers at end of each rubber should not be greater than 600mm from the adjacent wall. The last panel shall be placed at the side wall using edge profile 'L' Angle of size 20mm x 20mm and fixed to the side wall the false ceiling should be fixed of same level and should present a neat look

Supply and installation of Anutone (or) Euivalent Brand of Acoustical False Ceiling of subtex nubby, square edge, glass fibre core fully encapsulated ceiling tile of size 595 x 595 x 15mm having volume density 120 Kgs / m3, weight 1.8 / 2.4 / 3 kg / m2 which is suspended by using 0.3mm thick skelet trelis T15 metal grid system.Skelet trelis T15 metal grid system of 600 x 600mm module includes skelet WA15 W30 wall angle with unequal flanges of 15 / 19mm, length 3000mm, fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the skelet MT15 W36 MainT with flange width 15mm, height 32mm and length 3600mm, from the soffit slab with help of soffit cleat and wire rod with leveling spring clip at 1200mm centres. Skelet CT15 W12 CrossT with flange width 15mm, height 26mm and length 1200mm is interlocked into the pre-cut slots in the Main T15 at 600mm centers in......

the perpendicular direction to the Main T15. Finally, the skelet CT15W06 CrossT with flange width 15mm, height 26mm and length 600mm are interlocked into the precut slots in the CT15W12 CrossT in direction parallel to the Main T15 to result in 600 x 600mm module. The subtex nubby square edge of size 595 x 595 x 15mm shall be placed into the grid size of 600 x 600mm. Ensure arrow marks behind the tiles are oriented in one direction to achieve uniform shade. The systems to achieve noise reduction coefficient not less than 0.9 NRC, so as to have an neat appearance as directed by the department offices. The cost includes, cost of material, cost of labour, scaffolding, transportation, conveyance, etc.complying to standard specication.

Providing Wall Panelling using one side teak wood sheet with melamine polishing with following specification. The frame using aluminium tubular section of size 50mm x 25mm x 2mm thick fixing horizontally and vertically in position with wall at interval of 0.60m in both diretions, fixing water proof plywood of 12mm thick over the aluminium frame work with necessary screws. One side teak wood sheet of 3.5mm thick will be fixed over the plywood using fevical and finishing with melamine polishing and the rate inclusive of conveyance to site and labour charges and as directed by the Departmental Officers. The design pattern, water proof plywood, OST sheet and other materials to be used shall be got approved by the Executive Engineer concerned before use on work etc., complete.

Providing and fixing Acoustic Wall Panelling (equivalent to Armstrong) in channelled wood works perforated panels of width 192mm, thickness of 15mm and length of 2400mm or as per required by the Departmental Engineer made of a high density fibre board with minimum 725 kg./m3 density substrate with a laminated facing as per the approved shade and finish and a melamine balancing layer on the reverse side. The boards shall have a special peforation pattern where the visible surface has a "Helmholtz" fluted perforation of 3mm width and 21mm of visible panel each. The edges of the panels shall be "tongue-and-grooved" to receive special clips for installation. The back of the perforated panel shall have sound absorbing non woven acoustical fleese having NRC of 0.52. The panels shall be mounted on special aluminium splines using clips provided by Armstrong and approved by the Engineer-in-Charge.Installation: Install aluminium box section (provided by others) of section 50mm x 25mm or as approved by the Engineer-in-Charge on the solid wall horizontally using screws and plugs at spacing of 600mm centre to centre. Screw the aluminium extruded keel for channelled wood works

provided by Armstrong over the lowest and second aluminium section at an on centre distance of 600mm. Place the inside clip on the groove end of the panel along the aluminium keel and then place the tongue end of the next panel. Continue installing rows of panels by inserting the tongue into groove of the earlier inserted panel and progressively installing inside clips into the next keel till the actual height is achieved. Finish off the edges using wooden moulding of matching colour (provided by others). Installation to be carried out by Armstrong Trained Installation Team and installation should be carried out as per Armstrong Recommended Procedure.

Supply and fixing of curtains with MS rod of 25mm dia powder coated finish fire proof curtains with/without lining cloth etc.,complete and as directed by the departmental officers.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between.The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc.complete

Supplying and fixing fine polished Jet black granite slab of following thickness for cup-board arrangements including laying to correct alignment with necessary cement mortar and black powder etc, complete complying with standard specification and as direct.

Providing Cup-board Shutter using termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture fittings, such as, hydralic hinges, tower bolt, handles, multi purpose locks etc., as directed by the Departmental Officers. The design pattern, water proof plywood, laminate sheet and other materials should be got approved from the Executive Engineer befoe use on work.

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

160 mm dia pvc pipe

110 mm dia pvc pipe

Providing the safeguard for the columns for 1m height with rubber corner guard of 3"x3" L type colour of black and yellow approved quality etc. complete complying with standard specification and as directed by the departmental officers.

Drilling of bore wells 150 mm dia any where in Chennai city including transportation from the place with in the above district in alluvial soil sedimentary strata of clay and sand stone shale pebbles boulders etc by first taking pilot of 140mm/ 150mm/200mm dia and the enlarging to required dia by direct or revise rotary mud circulation method using contractor's rig fuel labour drilling betonies mud and water required for the drilling at the site shown by the departmental officers including construction of mud pit (Water available with in a lead of 1.5 Km) Drilling of 140/150/ 200mm pilot bore.

Reaming from 140 / 200mm dia pilot bore to 300mm dia bore as directed by the departmental officers upto 6M depth ending below Ground level

Supplying of 160 mm Dia Slotted PVC pipes of 6kg/cm2 (With slot or without slot) in the drilled hole including welding the joints etc., complete supplying and packing the annular space with pebbles size and quality as approved by the EE

Supplying of 160 mm Dia Plain PVC pipes of 6kg/cm2 (With slot or without slot) in the drilled hole including welding the joints etc., complete supplying and packing the annular space with pebbles size and quality as approved by the EE

Labour charges for inserting 165 /168 mm dia PVC casing pipes assemble (with slots or without slots) in the drilled hole including jointing the pipes with PVC coupler and with cement paste etc. complete and supplying and packing the annular space with pebbles of size and qualityas approved by the departmental officers. The conveyance charges to work site to be borne by the contractor.

Charges for developing the bore well for entire depth with suitable air compressor of 300RPM capacity (minimum 8 hrs) including transportation labour and fuel charges for compressor and directed by the departmental officers and conducting yield test by "V" notch methods, excluding the cost of bore charges and conveyance charges of handle boring.

Supplying laying and jointing HDPE pipes of 10kg/cm2 for borewell motor purpose of approved quality etc., complete and as directed by the departmental officers.

40mm Dia

Supplying and fixing of 5 HP of approved brand Submersible Pump with accessories of starter, Main switch, panel board etc. complete to suit the need (The pump set should be got approved by the Executive Engineer before supply)

Supplying and fixing of 5HP of approved brand monoblock with accessories of starter, Main switch, panel board etc. complete to suit the need (The pump set should be got approved by the Executive Engineer before supply)

Supplying and fixing of 3 Phase Panel Board including labour charges, complete to suit the need (The pump set should be got approved by the Executive Engineer before supply)

Supplying and fixing of suitable PVC end cap (6Kg/cm2) for 6" dia bore well of best quality with ISI mark. (The PVC end cap should be got approved by the departmental officers before execution)

Supplying and fixing and connecting of 4 core 16 sq.mm Flat Sub mersible cable wire for the sub-mersible motor from panel board to sub-mersible pump.

Supplying and fixing of 20mm dia Nylon rope for submersible motor of approved quality in etc,complete complying with standard specifications.

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

25 mm dia G.M. Gate Valve

32mm dia G.M. Gate Valve

40 mm dia G.M. Gate Valve

50 mm dia G.M. Gate Valve

Supplying and fixing in position 15mm dia following taps (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary.(Taps should be got approved by the Executive Engineer before use on the works)

Long body tap

Swan Neck Tap

Angle cock

Pillar tap

Supplying and fixing in position Stainless steel Two way Bib Cock with Health Faucet of Jaquar or equivalent make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (The material should be got approved by the Executive Engineer before use on the works)

Supplying and fixing in position Stainless steel shower rose with Shower Arm and Two in One Wall mixture of approved make jaquar or equivalent with stop cock arrangement of size 15mm dia inlet with necessary cutting, threading and jointing using shellac etc., complete complying with standard specification and as directed by the departmental officers (The material should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position of Stainless steel Bottle trap of Jaquar or equivalent make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (The materials should be got approved by the Executive Engineer before use on the works)

Supplying and fixing in position Frameless mirror of 5mm thick with size of 18 x 24 inch frameless modern mirror with beveled edges of Saint Gobin brand of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)

Supplying and fixing approved best quality brass Stainless steel towel rail 600mm long of approved make (Jaquar or Equivalent )with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Supplying and fixing best approved best quality Stainless steel soap tray of approved make jaquar or equivalent including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).

Supplying and fixing in position best quality approved make of Jaquar or equivalent under counter oval type wash hand basin of size 560 x 450mm with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Providing and fixing approved make jaquar or equivalent of white vitreous wall mounting type EWC with CP bolts, nuts, CI chair(painted with two coats of enamel paint over a coat of primer) or other hanging arrangemets, bakelite/polypropiline seat cover with CP hinges, rubber buffer, CP brass screw, washer with all accessories including cutting and making good the walls etc.,complete complying with standard specification and as directed by the departmental officers. (The materials should be got approved by the Executive Engineer before use on works).

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware with Twin type PVC flush tank of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Providing and fixing approved make jaquar or equivalent of concealed type cistern with dual flow facility comprising of actuator SS button facia assembly including brass / SS screws and washer complete providing protection cover over cistern cutting and making good the walls wherever required etc.,complete complying with standard specification and as directed by the departmental officers. (The materials should be got approved by the Executive Engineer before use on works).

Supply and fixing in position of best Indian make White Glazed Porcelain Oval Shape Special Type Urinal of size 382 x 398 x 601mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Executive Engineer before use on works.)

Supplying and fixing position CI Nahani Trap / Floor Trap of the size 100 x 75mm with stainless steel gratings with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position 150 x 100mm "P" or "S" stoneware gully trap 'A' grade with CI double gratings of size 150 x 150mm and 230 x 230mm at bottom and top respectively with necessary earth work excavation laid over a bed of brick jelly cement concrete 1:3:6 (One cement, Three sand and Six broken brick jelly) 150mm thick using 40mm size broken brick jelly including necessary brick work and plastering including dismantling masonry wherever necessary and re-doing the damaged portions to the original conditions using cement concrete 1:3:6 using 20mm stone jelly for fixing the gully trap and giving connections to stoneware sewer line etc., complete complying with standard specifications. [Earth work excavation, brick work, plastering shall be measured and paid separately]. The stoneware gully trap should be got approved by the Executive Engineer before use on works.

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications.(The PVC pipes should be got approved by the Executive Engineer before use on works).

75mm dia

110mm dia

160mm dia

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

PVC Elbow

160mm dia

110mm dia

75mm dia

PVC Elbow with Door

110mm dia

75mm dia

PVC Tee

110mm dia

75mm dia

PVC Tee with Single Door

110mm dia

75mm dia

160mm dia

110mm dia

75mm dia

PVC "Y" with Single Door

160mm dia

110mm dia

75mm dia

PVC Bend

160mm dia

110mm dia

75mm dia

Supplying and fixing in position PVC cowls of following dia of best approved quality conforming to BIS, etc., complete complying with standard specifications.(The PVC cowl should be got approved by the Executive Engineer before use on works)

110 mm dia

75 mm dia

Supplying, laying and jointing UPVC pipes of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, SS clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by Executive Engineer before use on works.

20 mm dia

25 mm dia

32 mm dia

40 mm dia

50 mm dia

Supplying UPVC Specials in water supply arrangements (both in internal and external water supply arrangements

UPVC Elbow

50 mm dia

40 mm dia

32mm dia

25 mm dia

20 mm dia

UPVC Tee

50 mm dia

40 mm dia

32mm dia

25 mm dia

20 mm dia

UPVC Reducer

50x40mm dia

40x32mm dia

32x25mm dia

25 x 20 mm dia

UPVC Reducer Elbow

50x40mm dia

40x32mm dia

32x25mm dia

25 x 20 mm dia

UPVC Reducer Tee

50x40mm dia

40x32mm dia

32x25mm dia

25 x 20 mm dia

UPVC Hex Nipple

50 mm dia

40 mm dia

32mm dia

25 mm dia

UPVC Union

50 mm dia

40 mm dia

32mm dia

25 mm dia

UPVC Coupler

50 mm dia

40 mm dia

32mm dia

25 mm dia

Supplying, laying and jointing CPVC pipes of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing CPVC specials using CPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, SS clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The CPVC pipes shall be got approved by Executive Engineer before use on works.

15 mm dia

20 mm dia

Supplying CPVC Specials in water supply arrangements (both in internal and external water supply arrangements

CPVC Elbow

20 mm dia

15 mm dia

CVC Tee

20 mm dia

15 mm dia

CPVC Reducer

20x15mm dia

Making through holes in Plain or Reinforced Cement Concrete with Diamond Core Drilling System by using BOSCH power tools of 150mm diameter Depth per cm

100mm dia

150mm dia

200mm dia

Packing the Toilet floor pipe corecutting for providing pipeline using Crystaline bonding agent which shall be applied as a bonding coat and non-shrink grout, after necessary surface grinding.

100mm dia

150mm dia

200mm dia

Construction of Inspection chamber or manhole of the following size including necessary earth work excavation in all soils to full depth as may be directed with sand filling at bottom of the chamber for 10cm thick, concreting CC 1:5:10 using 40 mm guage HBGs jelly 10 cm thick and sode walls 9" thick brick work in cement mortar 1:5 using Fly Ash Bricks of 230 x 110 x 70mm filling the size of foundation with excavated earth, plastering with cm 1:3 20m thick for inside and bottom and making necessary benching with brick jelly cement concrete to the required slope and finishing neatly etc., complete.

Supplying and fixing in position of Steel fibre reinforced cement concrete (SFRC)manhole / inspection chamber cover slab with following frame sizes including necessary labour charges for fixing the frame in position over the cement mortar base and finishing the joints etc. complete as directed.

600x600mm cover slab

750x750mm cover slab

Supplying and fixing of PVC mould CI Steps of approved quality including dismantling masonry wherever necessary and redoing the da maged portion to original condition

Supplying and Laying Rubber Moulded paverblock of 60-63mm thick with new one using cement concrete 1:2:4 for manufacturing, finishing, Curing and conveyence to site and laying etc., complete complying with standard specification and as directed by the deparmental officers.

Providing rain water harvesting pit of 900 mm dia and depth 2m below the ground level.The sides of rain water harvesting pit is provided with RCC well ring of inner size 900mm ,depth 250mm and 50mm thick . The top of rainwater harvesting pit is finished with brick work of inner size 1m X 1m ,0.60m height and 23cm thick with best quality II class ground moulded chamber burnt bricks of size 9" x 4-3/8" x 2-3/4" in Cm 1:5 (One of cement, Five of sand). The brickwork is provided above a base course of 10cm PCC 1:5:10 and over a sand cushion of 10cm.The top is covered with RCC cover slab of 50mm thick with perforated holes.The inner,outer and top surface of brick masontry are plastered with cement mortar 1:5(one cement and five sand)12mm thick.The rain water harvesting pit is filled with coarse river sand of 30cm depth at bottom,20mm HBGS jelly of 40cm depth at middle and 40mm HBGS jelly of 1.05m depth at top.The rate is inclusive of cost of all materials,transportation charges and labour charges etc complete and as directed by departmental officers.

Supply and fixing of Fire fighting application oblique type stainless steel Hydrant Valve of size 63mm –dia with oblique type instantaneous coupling with rotating wheel to open and close the valve including MS flange of table “E” , bolts & nuts with washer as per IS 5290 at ring main around the building and wet riser inside the building as directed by the department officers.

Supply, Installation of fire fighting application 180 degree swinging type, hose reel drum with 20mm dia braided thermoplastic hose of 30metres long so as to extend to necessary distance by self rolling spindle wheel including necessary 20mm dia ball valve & open & close spray nozzle, warm clip, etc., as per the standard pattern of any reputed make at every floor nearer to hydrant valve, including conveyance, all incidential charges, necessary scaffolding and redoing the dismantled portions to its original condition wherever found necessary etc., complete as per standard specification and as directed by the deparmtental officers. (Make : OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT).

Supply, and fixing in position of Fire fighting application Hose of 63mm dia of 15mts length binded by copper wire with 63mm dia Stainless steel male and female instantaneous fire fighting special coupling as per IS 901 as directed by the department officers Near every hydrant points including conveyance, all incidential charges, necessary scaffolding and redoing the dismantled portions to its original condition wherever found necessary etc., complete as per standard specification and as directed by the deparmtental officers. (Make : OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT).

Supply, and fixing in position of Fire fighting application 63mm dia stainless steel short length Branch Pipe with hexagonal type spray nozzle of 15mm (or) 20mm jet bore. Near every hydrant points. including conveyance, all incidential charges, necessary scaffolding and redoing the dismantled portions to its original cndition wherever found necessary etc., complete as per standard specification and as directed by the deparmtental officers. (Make : OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT).

Supply of Fire fighting application M.S. Hose Box so that to keep two numbers of Hose and one number of branch pipe with nozzle. It will have proper glass window type double door with universe open key, painted inside white and outside PO red. Near every hydrant point. including conveyance, all incidential charges, necessary scaffolding and redoing the dismantled portions to its original cndition wherever found necessary etc., complete as per standard specification and as directed by the deparmtental officers. (Make : OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT).

Supply and fixing nominal bore quartized bulb type sprinkler bulb 68 Deg C fast response pendent type including GI collar for each sprinkler bulb, mounted in MS pipe line using suitable size MS threaded coupling, thread, shellac etc., as per standard methods and including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, erection, testing and commissioning of following MS ‘C’ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm including necessary fittings like MS flange of table ‘E’, elbows, reducers, gaskets, bolt, nuts with washers & joints as per standard method of arc welding, including one coat metal primer and two coat Post Office Red painting including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: JINDAL / EQUIVALENT.

150mm dia

100mm dia

80mm dia

50mm dia

Wrapping and Coating Anti-Corrosive Treatment for under ground MS pipe having one coat of anti-corrosive metal primer, one layer of asphalt tar tape wound over the MS pipe as per standard methods as per standard specification as directed by the Departmental Officers.

150mm dia

Supply, erection, testing and commissioning of Cast iron body and bronze internal non-rising spindle sluice valve of sizes at required places to control the flow of water including necessary MS flange of table ‘E’, gaskets, bolts & nuts including conveyance, all incidential charges, necessary scaffolding and redoing the dismantled portions to its original condition wherever found necessary etc., complete as per standard specification and as directed by the deparmtental officers. (Make : OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT).2

100 mm dia

Supply, erection, testing and commissioning of Cast iron body and Gun metal or stainless steel internal Non-return valve of following sizes to control one way flow of water. To be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table ‘E’, gaskets, bolts & nuts, etc. as per IS 5312 including conveyance, all incidential charges, necessary scaffolding and redoing the dismantled portions to its original condition wherever found necessary etc., complete as per standard specification and as directed by the deparmtental officers. (Make : OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT).

100mm dia

Supply, erection, testing and commissioning of (0 to 14kg), range Pressure Gauge of reputed make with necessary valve, milling thread MS coupling fixed at delivery pipe line in pump house to read the developing pressure includng conveyance, all incidential charges, necesssary scaffolding and re - doing the dismantles portions to its original condtion whereever found necessary etc complete as per standard and as directed by the department officers. make : H - GURU / ISI MAKE / EQUIVALENT

Supply, erection, testing and commissioning of suitable Pressure Switch of reputed make line indfos or Donfos including necessary valves, couplings, etc., connected with electrical main control panel and setup at proper differential so as to auto start & auto stop the electrical motor, jockey motor includng conveyance, all incidential charges, necesssary scaffolding and re - doing the dismantles portions to its original condtion whereever found necessary etc complete as per standard and as directed by the department officers.

Supply, erection, testing and commissioning of Fire Fighting 4 Way Fire Brigade Inlet with necessary gun metal 63mm dia non return spring shutter arrangements, so that to control one way flow at the time of emergency water supply by fire and rescue service fire engine entry including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KIARTAR / OMEX / EQUIVALENT.

Supply, erection, testing and commissioning of Air Release Valve of 20mm dia, so as to release airlock in 100mm dia MS pipe at top most wet riser, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KARTAR / EQUIVALENT.

Providing, fixing pipe supports from columns / wall or suspenders from roof slab to suit various dia of pipes made out of GI / MS adjustable rods threaded for a sufficient length to adjust the height of support along with clamping arrangement for holding pipes of anchor fastening, arrangement design of hanger and should confirm with specification.

100mm dia

50mm dia

Supply and laying of 4 core 10 sq.mm. armoured copper cable for power wiring to the Terrace Pump Motor with runs of 14 SWG TC wire for earthing, providing in wall with suitable size GI clamps, screws, wooden plug, end termination by using suitable size cable glands, copper sockets and etc., as directed by the Departmental Officers.

Supply, erection, testing and commissioning of fire fighting application monoblock motor pumpset of 900 LPM at 40 metres head to develop 3.5 kg/sq.cm at the heightest and farthest hydrant point to make 30 m water jet at the time of fire fighting emergency cicumstances, coupled with 11 KW / 15 HP rated three phase 414 volts, 50 Hz, 2880 rpm electrical motor the pump with cast ron body, bronze impeller, rope gland packaging, suction size of 80 mm dia. delivery size of 65 mm dia., including the cost of foundaton concrete anti vibration mounting, rain safety hood and etc. complete as directed by the Departmental Officers (Kirloskar make KDS 1555+ or Equivalent)

Supply and providing 1000 Litres capacity priming tank made up of PVC (Make: SINTEX / EQUILANT)

Priming tank mounted with the supporting arrangement fabricated using MS angle for the height of 3.00 metres from the floor level, inlet, outlet and drain arrangements inside the fire fighting pump room as directed by the departmental officers.

Supply, erection, testing and commissioning of Fire Fighting Application Horizontal Centrifugal Type Pump rated for 2850 LPM at 70 metres head with Electrical Motor of 60HP of 415 volt, 3 phase connection complete with base plate and accessories. (Make Kirloskar or Equivalent). The rate inclusive of neessary vibration, bed mounting, etc., as per standard specifications and as directed by the Departmental Officers

Supply, installation, testing and commissioning of Diesel Engine Driven Main Fire Pump suitable for automatic operation and consisting of followings complete in all respects as required. a. 1 No. horizontal split casing centrifugal type fire pump capable of delivering 2850 LPM against a total head of 70 metres, so as to ensure a minimum pressure of 3.5 kg. per sq.cm at the farthest top most hydrant / outlet with pump casing of cast iron to grade FG 200, IS 210-1978 and parts like impeller, shaft sleeve, bearing ring, etc., of non-corrosive metal either like bronze, brass or gun metal and shaft of stainless steel. b. 68 BHP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant BS & IS standard complete. c. Auto starting mechanism, 12 volts / 24 volts electric starting equipment like self motor, dynamo, solenoid switches etc. d. 110 litres capacity diesel tank mounted over stand fabricated using 25mm x 25mm x 6mm size MS angle providing with level indicator, inlet port, outlet port, drain port and diesel return line port and fuel pre filter, after filter etc............

e. Exhaust system having flexible metallic mufler, 100mm dia MS heavy pipe extended upto 1m outside pump house duly insulated with 50mm thick glass wool with 1mm thick aluminium sheet cladding, residential silencer with necessary MS support arrangements from wall or ceiling as per site condition. f. Dash board consisting of the instruments like Temperature Gauge, Galvano Type DC Ammeter, Lubricant Oil Pressure Gauge, Ignition Switch, Emergency Stop and all other protection equipments as per specification, stop soleneid for auto stop in the event of fault with audio indications, painted with Post Office Red Colour etc., as required. g. 12 V / 24 V, storage battery, maintenance free tape, 180AH rating. MS fabricated common base plate, coupling guard, foundation bolts, etc., as required. h. Positioning the Diesel Engine Driven Fire Pump over cement concrete foundation using suitable size anti vibration mounting arrangements. All works including conveying, fixing and incidental charges, etc., completed as per standard specification and as directed by the Departmental Officers. (Make: KIRLOSKAR / EQUIVALENT).

Supply, erection, testing and commissioning of 180 LPM, 70 metres Head Pressurization Pump with 10HP electrical motor of Kirloskar make with suitable base frame including necessary vibration bad mounting etc., including conveying, fixing and incidental charges, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KIRLOSKAR / EQUIVALENT.

Supply, erection, testing and commissioning of following sizes of Heavy Duty Foot Valve including all accesories, such as, MS flange of table ‘E’, gaskets, bolts & nuts, etc., installed at end of 150 / 200mm dia suction pipe line at sump including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete and as per standard specification and as directed by the Departmental Officers. Make: NORMEX / KARTAR / EQUIVALENT

100mm dia

Supply and laying of following sizes of armoured Aluminium / Copper cables for electrical motor, control panel, pressure switch, jockey motor etc., all incidential charges, necesssary scaffolding and re - doing the dismantles portions to its original condtion whereever found necessary etc complete as per standard and as directed by the departmental officers.Make : POLYCAB / PARACON / FINOLEX / EQUIVALENT

3 core 185 sq.mm. armoured aluminium cable

3 core 10 sq.mm. armoured copper cable

10 core 2.5 sq.mm. armoured copper cable

2 core 2.5 sq.mm. armoured copper cable

Earthing arrangements with GI earth plate including charcoal and salt with necessary excavation and masonry work as per the standard method as directed by the department officers.

Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc, complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT

Supply and fixing of Carbon-di-Oxide Gas Type 2 kg. capacity Fire Extinguisher as per New IS15683, complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc., complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT

Supply, installation, testing and commissioning of Micro Processor based conventional 8 Zone Fire Alarm Control Panel having the rating of 24 volt DC power supply, consisting 230 / 24 volt SMPS unit, 2 Nos. of 12 volt 7 AH standby batteries, suitably mounted on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers.

Supply, installation, testing and commissioning of Conventional Smoke Detector suitably mounted on ceiling with MS juction box / false ceiling using fixing accessories like screws, plug, clamps, etc., as per standard methods and as directed by the Departmental Officers. (Make: Apollo / Equivalent)

Supply, installation, testing and commissioning of Manual Call Point (MCP) providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers. (Make: Ravel / Equivalent)

Supply, installation, testing and commissioning of Electronic Hooter / Sounder providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers (Make: Ravel / Equivalent)

Supply and laying of FRLS PVC insulated 2 core 1.5 sq.mm. Armoured Copper Cable on ceiling / wall using fixing accessories like screws, plug, clamps, etc., as per standard methods and as directed by the Departmental Officers.

Supplying and fixing of King size Cot with Bed Side Box, Bed, Pillow, Pillow cover, Bed Spread. The external frames of cot 6½ X 6 are made up of teakwood, the internal frames are made up of Kongu or equivalent wood and the top plywood is 12mm in thickness. They are completely melamine polished. Bed 6½ X 6 Branded 6" thickness Mattress with Pillow, Pillow Cover, Bedspread etc., complete complying with standard specification.

Supplying and fixing of VVIP Dinning Table of Teakwood with Melamine Polish. The rate includes labour for manufacturing, supply, transportation, etc.,as directed by departmental officers.

Supplying and fixing of Dinning Table of Size 7 X 3 feet oval table with 6 chairs Teakwood with Melamine Polish. The rate includes labour for manufacturing, supply, transportation, etc.,as directed by departmental officers.

Supplying and fixing of Three seater Sofa with basic Silver Wood framework. The seat have flat type High Density cushions placed on the seat, back rest with fireproof cloth or leatherride. Bottom Legs with Floor Adjustable bush model sofa. The rate includes labour for manufacturing, supply, transportation, etc., complete complying with standard specification.

Supplying and fixing of Two Seater Sofa with basic Silver Wood framework. The seat have flat type High Density cushions placed on the seat, back rest with fireproof cloth or leatherride. Bottom Legs with Floor Adjustable bush model sofa. The rate includes labour for manufacturing, supply, transportation, etc., complete complying with standard specification.

Supplying and fixing of Teapoy of Size 900x600mm Teakwood with Melamine polish. The rate includes labour for manufacturing, supply, transportation, etc., complete complying with standard specification.

Supplying and fixing of 3 seater Stainless Steel dining table with 3 Wooden Chairs. Chair Cushion Seat & Reaper back ;Made out of Good quality of wooden frame,2''Latex Rubber for seat with upholstry cloth and good polish finish complete complying with standard specification.

Supplying and fixing of VIP Chair made of Teak Wood Chair with Cushion Seat & Cushion back ;Made out of Good quality of Teak wood frame,2''Latex Rubber for seat with upholstry cloth and good polish finish complete complying with standard specification.

Supplying of Visitor Chair with back in frame covered with breathable Mesh in black for back, with arm steel frame and leg chair 14 gauge CR round pipe legs, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, fixed arms, legs have nylon bushes. The rate includes labour for manufacturing, supply, transportation, etc.,

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed FRLScopper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Lower End

Supply and Fixing of 4' 22 W LED Light Fitting without tube and 20W tube light T8 fitting unsheathed copper leads from terminals to the fittings.

Renewal by supply and fixing of Integra neo 24W LED(175mm) round recess mounted downlight with die cast aluminium heatsink with PVC unsheathed copper leads from terminals to the fitting (Havells/Equ)

Renewal by supply and fixing of 2 x 2 42W LED square recessed fitting PLUTONEO2x2PLR42WLED857 with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting (Havells/Equ)

Supply and fixing of WT bulk head fitting with guard suitable for 11W CFL lamp with CFL

Supply and Fixing of Wall Bracket LED fitting on wall with unsheathed copper leads from terminals to the fittings. (Havells/Equivalent)

Supply and Fixing of LED Mirror light fitting on wall with necessary connections.

Supply and fixing of 48W LED Street light fittings with suitable wall mounting Ms clamps on the wall with necessary connection.

Supply and fixing of 400mm (16") Sweep wall mounting fan on wall with necessary connection.

Renewal by supply and fixing of 1200mm (48") sweep AC ceiling fan complete ( Higher end) with 2 module 100W fan step regulator (Higher end) with 300mm down rod with fan clamp with side plates and cross arm.

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete without provision of hole in the wall

Supply and fixing of louvers shutter arrangements for 300 mm (12”) sweep (light duty) AC Exhaust fan.

Supply and fixing of 1Module flush box with suitable front plate, 1No Call bell and 1 No 6A Bell Push in flush with wall with necessary connection.

Supply and fixing of 3 Module flush Box With Front Plate With 1No 6A Modular Switch and 1No 6A Modular Socket in flush with wall with necessary connection

Supply and fixing of 3 Module flush Box With Front Plate With 1No 16A Modular Switch and 1No 16A Modular Socket in flush with wall with necessary connection

Supply and fixing of 9 Module flush Box With Front Plate With 2Nos 6A Modular switch, 2Nos 6A Modular Socket, 2No 16A Modular switch and 2No 16A Modular socket in flush with wall with necessary connection

Supply and fixing of 25A flush type wall socket 25ADP MCB complete set for AC plug in flush with wall with earthconnection (For AC Plug)

Supply and fixing of 63A FP MCB with 4 pole enclosure in flush with wall with necessary connection.

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 40A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 4 way Horizontal Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 40A 4P MCB switch as incoming and 12 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of Vertical type 8way triple pole neutral MCB distribution board with Metal/Acrylic Door cover with IP42 Protection, with 1 No 63A 4 pole MCB as incoming and 3 Nos 32AA TPMCB Isolator and 15 nos 6A- 32A SPMCB as Outgoing flush with wall and making good of the concealed portion with earth connection only.The MCB DB and MCB’s should be with ISI mark.(Like Legrand /Hager L &T make) (Common)

Supply and fixing of Vertical type 4 way triple pole neutral MCCB distribution board with Metal/Acrylic Door cover with IP42 Protection, with 1 No 125A 4 pole MCCB as incoming and 3 Nos 63A TPMCB and 3 nos 6A-32A SPMCB as Outgoing with suitable cable entry box in flush with wall and making good of the concealed portion with earth connection only.The MCB DB and MCB’s should be with ISI mark.(Like Legrand /Hager L &T make) (AC)

Renewal by supply and fixing of 4 way vertical Triple pole neutral MCB sheet steel distribution board with double door (metal) with 1 No 63A 4P MCB Isolator as incoming ans 12 nos 6A to 32A SP MCB as outgoing on wall with earth connection only. Higher end.

Renewal by Supply and run of 2 of 1.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 4 sq.mm copper wire with painting of suitable colour

Supply and run of 2 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in rigid pipe concealed in wall and ceiling with continuous earth wire connection of 4 Sqmm Cu wire and making good of the concealed portion with suitable colour

Supply and run of 2 of 6 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour

Supply and run of 4 of 10 sq.mm. (140 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 14 SWG TC wire and making good of the concealed portion with suitable colour

Renewal by Supply and laying of 4 x 16 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good

Supply and clarnping of 3-1/2x 70 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for 3-1/2 x 70 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 70 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and laying of 3-1/2 x 185 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good

Supply and fixing of brass cable gland for 3-1/2 x 185 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 185 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and laying of 3 1/2 x 120 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good

Supply and clarnping of 3 1/2 x 120sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for 3-1/2 x 120 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 120 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply, Erection, Testing and commissioning of 125A capacity Dust and Vermin Proof Cubical Panel Board made up of 16 SWG CRCA sheet steel with supply and fixing of the following interior mounting switches with a central bus bar chamber and two nos of Horizontal or vertical cable chambers at the two ends one on each side and confirming to IE rules.

The fuse switches should be connected with the phase and neutral buses with suitable size of rigid copper rod or flat and each switch should be connected with 2 nos. 25x3 mm earth bus with 2 runs of No:8 SWG rigid copper rod with suitable lugs. Phase and neutral copper buses should be tinned properly.The incoming 125A switches should be connected to the bus with same size of 1 x 1/8 fixed copper flat, outgoing 63A switches should be connected to the bus by 1 x 1/8 fixed copper flat.The panel should have a separate metering chamber at the top side consisting of Digital Multifunction meter Model LT MFM 4410 LED meter Cl 0.2/ like and CT arrangements LED indicator lamps should be provided with control switches and fuse units. The panel should be painted with one coat of Red oxide as primer coat and two coats of enamel paint of siemens grey and also the danger board. The capacity of fuse switches, size of the incoming and outgoing cables, the place to which the supply is fed shall be marked on switch chamber.

Supply and Erection of 250 A floor mounted cubical panel board suitable for operation on 415V/50Hz with bus bar chamber made up of 16SWG Thick CRCA Sheet with 1"x1/4" tinned copper flats for 3 phases and neutral with 6mm Hylem sheet separation of 3 phases and neutral and with synthetic moulded insulators bus support at equal intervals as per IS Specification and 1" x1/8" Copper flat on rear side of the panel board for earth buses with the following switches complete 1. 250A FP MCCB -1 No 2.125A FP MCCB -4 Nos 3.63A FP MCCB -8 NOS with rotary handles and spreader terminals, multi functional meter, Metallic Danger Board, pilot lamp toggle switches, powder coated painting ,PVC colour coding for R,Y,B,N, necessary identification of out going loads ,bus capacity cable size with bold letter with display (Make L&T /Equivalent)

Supply and earthing as per PWD standard with an earth electrode of 2 metre Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work

Supply and run of No.8 SWG hard drawn copper conductor concealed in wall and making good of the concealed portion.

Supply and run of 1 of No.8 SWG GI wire for earth connection

Supply and fixing of 65 mm 2 1/2 GI Pipe (Class – B) of 6 Mtr length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting of masonry pedestal with suitable MS box to house 6A SP MCB with suitable angle iron frame work, with door and with lock and key arrangements and supply and fixing of 80W LED Street light fitting with necessary clamps, on the above post with PVC unsheathed leads with painting of suitable colour.

Supply and Erection of 415V/50Hz Cubical Metering Panel board with bottom bus bar chamber and switch chamber on top side of the bus bar chamber and metering chamber with viewing glass in the middle with 16SWG Thick CRCA Sheet with 1"x1/4" tinned copper flats for 3 phases and neutral with 6mm Hylem sheet separation of 3 phases and neutral and with synthetic moulded insulators bus support at equal intervals as per IS Specification and 1" x1/4" Copper flat on rear side of the panel board for earth buses with the following switches complete. 1. 250A TP SDF Switch -2 Nos (SDF Switches L&T Make /equivalent), 6 Nos 200A Porcelein fuse units and 2 Nos 200A Neutral link, Danger Board with powder coated painting ,necessary identification of out going loads ,bus capacity cable size with bold letter with display (Make L&T /Equivalent)

Supply, Erection, Testing, Commissioning and Handing over of 1 No Gearless 13 Persons Capacity Passenger Lift as per following technical specifications including all taxes and duties. Technical Specifications: 1. Location: Guest House with Multi purpose hall 2. No of Lift: One No. 3. Type of Lift: Passenger 4. Capacity of Lift : 13 Persons Passenger (884 Kgs) 5. Speed: 1.0 mtr /Sec 6. Type of Drive: Microprocessor based specific variable voltage variable frequency V3F Drive with enhanced ride comfort and near zero leveling functions. 7. No of floor: Ground + 3 floors. 8. Total Travel: 18 Mtrs Approximate. 9. Leveling Accuracy: High level accuracy with smooth & jerk free stopping. 10. Construction of car: Special car made of Stainless Steel Hairline finish & panels with direct lighting and new beautiful single tile false ceiling with tubular handrail and mirror. 11. Position of Machine: Directly above the lift well. .

12. No. of Landing Entrance: One in front 4 Nos only. 13. No. of Car Entrance: One in front only. 14. Car Entrance Door: Automatic Centre opening door with steel painted finish with full length infra red sensor for better safety. 15. Landing Entrance Door: Automatic centre opening door with steel painted finish with emergency opening device. 16. Lift well: 2800mm (width) x1650mm (depth) available size.17. Lift pit depth available: 1600mm 18. Car size: 1100 mm wide x 2000mm deep (Part I) – 2200). 19. Car clear Opening: 900mm (as per IS 14665 (Part-I) – 2000). 20. Lift Machine Room: As per standard specification. 21. Power Supply: 415v, 3 phases, 50 C /Sec A.C supply for power and 230 V, 50 Hz single phase AC supply for light. 22. Control: Microprocessor Computer based – simplex collective full collective logic system with/without attendant mode. 23. Car fittings: LED lighting with 1 no 300 mm sweep cabin fan. 24. Lift Well: RCC construction with Brick masonry. 25. Indication: Up/Down Digital Direction scroll type and position indicator for all landing and in car.

26. Emergency Alarm Bell: Battery Operated Alarm Bell to be provided with automatic charging device. 27. Emergency Light: Battery operated Light to be provided with automaticCharging device 28. Fireman’s switch: To be provided at ground floor. 29.Minor Builders Work: To be provided By Lift contractor. 30.Scaffolding: To be provided by lift Contractor. 31. Stainless Steel sill angles and facia Plates: To be provided by lift contractor. 32. Steel for lift Machinery: To be Provided by lift contractor. 33. Servicing and Maintenance: Free Comprehensive servicing and maintenance should be provided by lift contractor during the guarantee period of one year. 34. Provision of intercom with phone to be provided by lift contractor. 35. Lift License: Preparation of drawing, Payment of charges to CEIG and insurance policies if any and obtaining CEIG safety certificate and lift license as per lift act should be done by lift contractor. 36. Automatic rescue device – To facilitate the landing of the nearest floor at the time of power failure. This shall consist of suitable type battery system with charges inverter, under voltage protection system etc.

37. Floor annunciation system with music. 38. Special futures: (a). Infra red door sensor withFull height screen. (b). Full width half height rear panel Mirror. (c).Voltage stabilizer for circuit control. (d). Tubular Stainless Steel hand rail in car (e). Signal Fixtures (f). Vandal proof S.S. button with S.S. cover. (g). Stainless steel door frames (h). V3F door operator (i) Call register signal (j) Pit ladder (k). Braille buttons (l).Stainless steel facia for car operating panel and landing fixtures. (m). ON-OFF switch for fan and Light. (n) Over load warning indicator.

39. Over speed governor, phase failure and phase reversal relay, alarm bell, Guide brackets for car and counter weight, rubber padding under winding unit, Motor of adequate capacity, single reduction worm gear, electromagnetic brake with compression springs, car safety gears, buffer, electro mechanical door locks, emergency key, side supporting angles, motor over load protection devices, final limit switch, main suspension ropes, counter weights, lifting joint joist for mounting the machineries. 40. Guarantee: Guarantee for the Materials& workmanship of equipment’s complete should be offered by the Lift firm for a period of not less than one year. 41.Site testing in accordance with IS 14665 should be carried out at the time of handing over.

Supply, Erection, Testing, Commissioning and Handing over of 1 No Gearless Persons Capacity Passenger cum Service Lift as per following technical specifications including all taxes and duties. Technical Specifications: 1.Location: Guest House With Multi purpose Hall 2. No of Lift: One No. 3. Type of Lift: Passenger cum Service Lift 4 .Capacity of Lift : 20 Persons (1360 Kgs) 5 .Speed: 1 mtr /Sec 6.Type of Drive: Microprocessor based specific variable voltage variable frequency V3F Drive with enhanced ride comfort And near zero leveling functions. 7. No of floor: Ground + 3 floors. 8 .Total Travel: 18 Mtrs Approximate. 9 Leveling Accuracy: High level accuracy With smooth & jerk free stopping. 10 Construction of car: Special car made of Stainless Steel Hairline finish & panels with direct lighting and new beautiful single tile false ceiling with tubular Handrail and mirror. 11 .Position of Machine: Directly above The lift well. .

12. No. of Landing Entrance: One in front 4 Nos only. 13 No. of Car Entrance: One in front only. 14 Car Entrance Door: Automatic Centre opening door with steel painted finish with full length infra-red sensor for better safety. 15 Landing Entrance Door: Automatic centre opening door with steel painted finish with emergency opening device. 16 Lift well: 2500mm (width) x3000mm (depth) available size. 17 Lift pit depth available: 1750mm 18 Car size: 1300 mm wide x 2400mm deep (Part I) – 2200). 19 Car clear Opening: 1000mm x 2000 mm (as per IS 14665 (Part-I) – 2000). 20 Lift Machine Room: As per standard specification. 21 Power Supply: 415v, 3 phase, 50 CY /Sec A.C supply for power and 230 V, 50 Hz single phase AC supply for light. 22 Control: Microprocessor Computer based – simplex collective full collective logic system with/without attendant mode. 23 Car fittings: Compact fluorescent lighting with 1 nos 300 mm sweep cabin fan. 24 Lift Well: RCC construction with Brick masonry. 25 Indication: Up/Down Digital Direction scroll type and position indicator for all landing and in car.

26 Emergency Alarm Bell: Battery Operated Alarm Bell to be provided with automatic charging device. 27 Emergency Light: Battery operated Light to be provided with automatic Charging device. Fireman’s switch: To be provided at ground floor. 29.Minor Builders Work: To be provided By Lift contractor. 30.Scaffolding: To be provided by lift Contractor. 31. Stainless Steel sill angles and facia Plates: To be provided by lift contractor. 32 Steel for lift Machinery: To be Provided by lift contractor. 33. Servicing and Maintenance: Free Comprehensive servicing and maintenance should be provided by lift contractor during the guarantee period of one year. 34. Provision of intercom with phone to be provided by lift contractor. 35. Lift License: Preparation of drawing, Payment of charges to CEIG and insurance policies if any and obtaining CEIG safety certificate and lift license as per lift act should be done by lift contractor. 36. Automatic rescue device – To facilitate the landing of the nearest floor at the time of power failure. This shall consist of suitable type battery system with charges inverter, under voltage protection system etc.

37. Floor annunciation system with music. 38. Special futures: (a). Infra-red door sensor with Full height screen. (b). Full width half height rear panel Mirror. (c).Voltage stabilizer for circuit control. (d). Tubular Stainless Steel hand rail in car (e). Signal Fixtures (f). Vandal proof S.S. button with S.S. cover. (g). Stainless steel door frames (h). V3F door operator (i) Call register signal (k) Pit ladder (k). Braille buttons (l).Stainless steel facia for car operating panel and landing fixtures. (m). ON-OFF switch for fan and Light. (n) Over load warning indicator.

39. Over speed governor, phase failure and phase reversal relay, alarm bell, Guide brackets for car and counter weight, rubber padding under winding unit, Motor of adequate capacity, single reduction worm gear, electromagnetic brake with compression springs, car safety gears, buffer, electro mechanical door locks, emergency key, side supporting angles, motor over load protection devices, final limit switch, main suspension ropes, counter weights, lifting joint joist for mounting the machineries. 40. Guarantee: Guarantee for the Materials& workmanship of equipment’s complete should be offered by the Lift firm for a period of not less than one year. 41. Site testing in accordance with IS 14665 should be carried out at the time of Handing over.

Supply, erection, testing, commissioning and handing over of 1No 125 KVA Diesel Generator set of 0.8 P.F. Three Phase 415/420 Volts, 50 C/S, 1500 RPM as detailed below. 1. ENGINE Water cooled diesel engine suitable for Generator Application with a shaft output of 156 BHP at 1500 RPM under NTP condition as per BSS 5514/IS 10000. The Engine shall comprise the following Standard scope of supply. (Make:Kirloskar/Cummins/AshokLeyland/ Greaves) 1. Dry type Air cleaner 2. Expansion bellow 3. Radiator, Radiator fan and mounting 4. Air to Air charge cooler 5. Exhaust Gas turbo charger 6. Lube oil cooler and Lube oil filter 7. Fuel filter (pre and micro) 8. In-Line Mono-block fuel injection pump with governor fuel feed pump 9. Electronic governor 10. 24V Battery charging alternator 11. 24V Volt electric starter motor 12. Engine test certificate 13. Residential muffler.

14. Fly wheel with starter ring ENGINE INSTRUMENT PANEL MOUNTED Engine control panel consisting of ON /OFF /START Key Lube oil pressure gauge, Oil Temp gauge, High water temperature gauge and electronic hour meter and RPM indicator. SAFETY SYSTEM OF ENGINE: The Engine shall trip for the following conditions with visual alarm device. 1. Low Lubricating Oil pressure High Water temperature Vee-belt failure and over speed, The visual indicator should also be providing for low battery indication. The Engine should be capable of providing 10% over load for one hour for every 11 hours continuous running at full load 2. ALTERNATOR: Alternator capacity of 125KVA/100 KW, AC 3 Phase, 50HZ,415Volts, 0.8 P.F. 4 wire self excited, self regulated designed to run at 1500 RPM under NTP conditions conforming to BS 5000 /IS 13364 (Part-II) 1992 to be coupled directly to the Diesel Engine and Test certificate. (Make: Kirloskar/ Crompton/ Greaves /Equivalent).

26. 1 Set Pilot lamps of 3 Nos 27. MCCB of 250 A capacity with magnetic thermal over lead release, instant short circuit trip and under voltage release switch 28. Rectangular copper bus bars (1 No for each phase, neutral and earthing terminal) of adequate capacity duly colour coded with heat shrinkable PVC sleeves. 29. 1 No Mains Voltage monitor 30. Hooter/ Audio Alarm for indication set fails to start and for DG O/L 31. 1 Set Timers 32. Audio and visual indication arrangements for a. Low Lubricating Oil pressure b. High water temperature c. Over speed 33. 1 No Earth fault relay 34. Isolator to Isolate the neutral NOTE: 1. The control panel should be complete with necessary fuses, cables, labels, other accessories with isolation arrangements. 2. The engine should trip for the following conditions a. Low Lubricating Oil pressure b. High water temperature c. Over speed

4.ACOUSTIC ENCLOSURE: Acoustic enclosure shall be powder coated and Fabricated of 16 SWG CRCA MS sheet. The silent canopy shall be of nut bolt type construction. Critical processes of punching are done on CNC Machines to maintain dimensional accuracy of hole within 0.1 mm. Powder coating done after seven-tank surface preparation process of sheet metal. Canopy panel and doors shall have inside lining of FIRE RETARDANT 64Kg/m density Mineral wool of 100mm Thickness as acoustic material. Four hinged doors shall be provided to canopy. The average sound level at 1Mt. distance shall be as per latest CPCB norms. Surface Treatment – Painting: The enclosure surface shall be suitably treated for degreasing de-rusting and posphating. The canopies are passed through seven- tank treatment thoroughly. Additional features of Canopies: Canopy fabricated on CNC machines with dimensional Accuracy of 0.1mm so as to increase its durability. Special designed supporting rips/ structures are used in canopies so as to be sturdy steadiness and to reduce the vibrations of the DG sets if any. World class Cooling Package:

35. Canopies shall have Cooling package for which it can also perform at 45˚ deg C/ ambient temperature No grouting required on the ground only a level surface capable of withstanding the DG weight. Lifting hooks shall be provided for the acoustic Enclosure, which should be unloaded independently of the DG Set. The Gen set frame shall also be provided with hooks for unloading. Temperature rise inside the canopy Canopies shall be designed so as to maintain the temperature difference between ambient and air inlet at cleaner within the enclosure well within 5-7 deg centigrade as per the latest norms. 5.FUEL TANK: 230 Ltrs. Removable fuel tanks shall be fabricated out of 14SWG CRCA MS sheet and is part of base frame. It is duty painted and fitted with inlet and outlet connections and mechanical fuel gauge. Fuel tank can be easily removed for clearing or any maintenance.

6.BASE FRAME: Base frame should be fabricated in sheet metal. The base frame is rugged in construction and designed for mounting engine and brush less alternator closely coupled with cross members mounted on AVM. The base frame shall be provision for mounting of acoustic enclosure on it. The supply of generator set includes loading unloading and transportation charges. 7.BATTERY: 2Nos 12V 180AHR Battery. 1. Preparation of site plant physical layout electrical line schematic diagram in 10sets, getting drawing approval from CEIG preparation completion report, rectification report and arranging CEIG inspection and obtaining CEIG safety certificate preparation of 2sets of approved drawing and a copy of safety certificate in a neat frame work to be fixed in generator room and payment of CEIG inspection fees for 125 KVA Genset.

Erection of Generator set: Erection, Testing, Commissioning and Handing over of the Generator set with suitable concrete foundation with cement concrete 1:2:4 with sand cushion all around the foundation erection of 125 KVA Generator set over the foundation and with proper alignment over the existing foundation and with proper alignment over the existing Foundation to suit 125 KVA Gen set. Including supply and fixing of ‘Dunlop’ make anti vibration mounts to the Generator set.

Supply and installation of exhaust piping of sufficient length with suitable MS pipes so as to extend outside the generator room with necessary thermal insulation.

Supply of lubricating oil and first charging of starting battery and supply of Diesel as per full load capacity of diesel tank.

Supply and run of 6 core 2.5Sq.mm PVC insulated sheathed multicore copper round flexible cable with suitable PVC pipe complete.

Renewal by supply and fixing of 2 feet Bollard fitting (with foundation G.I pipe) complete with 9W E27 LED bulb with necessary connection.(KLITE/Equ)

Renewal by Supply and run of 4 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire with painting of suitable colour

Design, Supply Installation, testing and commissioning of 11.0 TRnominal capacity ceiling suspended Ductable Air conditioner with theFollowing components.a) 11.0 TR capacity ceiling suspended Ductable Air Conditioner high tech,low height, low noise level indoor unitwith fin and tube type cooling coil,Detachable type drier provided inrefrigerant circuit to reduce moisturecontent multi stage type distributorfor feeding equal quantities of theRefrigerant mixture to all the section ofthe coil, with required valves, directlycoupled blower to reduce troubles andwear & tear compared to belt driveBlower. Thermostatic expansion valve arrangement, lift and pull type aluminium framed durable, washable air filter, Integrated electrical panel with complete microprocessor control with display for easy operation and maintenance of unit common operating conditions of 45 F suction temperature Auto reset type HP/LP safety cut sensor type to improve Reliability of compressor. Type QTY- Ceiling Suspended Blower QTY – 1 Nos Motor Power – 415V /3Ph/50HZ Air flow -4400 CFM

B)11.0 TR capacity suitable for ceiling suspended Ductable Air conditioner high tech Outdoor unit with power saving high efficiency sturdy and rugged 1 No of scroll compressor each with inbuilt internal thermal protector, internal pressure relief valve, Auto reset type HP/LP safety cut sensor out to improve reliability of compressor andcondenser shall be made of super slithigh efficient aluminium fins mechanically bonded to copper tubescondenser ‘L’ type coil to be rigidlyfixed to unit frame with fastenersimported condenser fan & fan bladesto be statically and dynamicallybalanced to reduce noise andVibration. The fans are direct driven3phase motor with protection.Condensing temperature 130’f for thesystem operations. Refrigerant Compressor – Scroll No of Compressor – 1No Refrigerant – R410/R407A Power supply – 415V/3Ph/50HZ No of Fan – 1Nos Types of Mounting – Rubber mounts with sleeve

Supply and filling of R410/R407/R32 Refrigerant Gas.

Supply & fixing of hard drawn copper Refrigerant piping of suction line of Size 1 1/8” inches with necessary fitting and clamp etc.

Supply & fixing of hard drawn copper Refrigerant piping of liquid line of size 5/8” inches with necessary fitting and clamp etc...

Supply and fixing of flexible canvas connection between indoor unit and ducting and rubber pads, with ceiling Support angle rods etc.

Supply and fixing of suitable MS angle frame if required necessary Base frame for mounting the outdoor units for protection from the rain water with dust flow on the open trace / corridor Floor area

Supply, Fabrication and Installation of GI ducting Ducting arrangement with necessary angle supports, anchor fasteners and threaded rods etc. as required

Supply and Providing Thermal Insulation of 9mm thick –XLPE with aluminium foil./ Nitrile Rubber insulation

Supply and providing acoustic lining for initial portion of ducting with 10mm thick XLPE insulation.

Supply, fabrication and fixing of Volume control dampers individually across the duct

Supply and fixing of powder coated Extruded aluminium supply air grilles/diffuser with MS volume control damper for supply.

Supply and fixing of 1 inch PVC water drain pipe line on wall with suitable Clamp as required.

Towards charges for welding, leak testing, Nitrogen pressure testing, pressure holding, vaccummising, dehydration and other related works etc.

Supply, fabrication and fixing of suitable angle support frame for ceiling mounted the Indoor Units.

Supply and providing of pipeline nitral rubber insulation for section line Refrigerant pipe as required.

Supply & providing of Power supply for MCB to Outdoor unit with 4 core 10 sq.mm copper flexible cable

Supply & providing of control supply for Outdoor unit to Indoor unit HP and LP cut-outs with 7 core 1.5sq.mm copper flexible cable

Supply ,Erection,Testing and commissioning of 1.5TR split type Air conditioner with one outdoor air cooled condensing unit and indoor evaporator with inter connection of copper refrigerant piping between condensing unit and evaporator unit electrical cabling of performing cooling ,dehumidifying air circulating filtering etc.. suitable for operation on 230V 50Hz single phase. (Make: Carrier, Toshiba/ Equivalent)

Supply ,Erection,Testing and commissioning of 2.0TR split type Air conditioner with one outdoor air cooled condensing unit and indoor evaporator with inter connection of copper refrigerant piping between condensing unit and evaporator unit electrical cabling of performing cooling ,dehumidifying air circulating filtering etc.. suitable for operation on 230V 50Hz single phase. (Make: Carrier, Toshiba/ Equivalent)

Supply and fixing of 4KVA wall mounting type Automatic voltage stabilizer with time delay arrangements suitable for operation at 230 Volt, 50 Hz, AC power supply (Make: V –Guard)/ Equivalent.

Supply and fixing of 5KVA wall mounting type Automatic voltage stabilizer with time delay arrangements suitable for operation at 230 Volt, 50 Hz, AC power supply (Make: V –Guard)/ Equivalent.

Supply and Installation of Additional copper pipe with necessary insulation, Cabling & Drain arrangement etc…

Supply and fixing of angle iron stand for outdoor Unit

Supply and Installation of 12 Zone automatic Conventional fire alarm panel with fire and fault indications, system reset, alarm cancel and lamp test buttons. Panel shall be wall mounted type with inbuilt battery and battery charger. Panel shall operate on 230 v ac single phase supply. AGNI/EQVLT

Supply and Installation of smoke detector with base and LED to operate on 24 V dc supply. Make System Sensor/wizmart//wels

Supply and Installation of Electronic hooter 5 watts capacity wall mounting type.Make naveen, wels

Supply and Installation of Manual call points with hammer and chain. Make naveen wells.

Supply and installation of 2 core x 1.5 sqmm copper Armoured cable fixed on wall or ceiling with clamps, junction boxes, screw.

Supply and Fixing of 250A Three Phase 500V 4Pole Change over Switch on suitable angle iron frame work with MS cable entry boxes with PWD earthing

Supply and Installaion of 60W line array column speaker with Switchable voicing provides flat response in music mode or mid-range presence peak in speech mode,Built-in 70V/100V transformer, plus 8 ohm direct capability. etc. Make;JBL/Eq. Model No:CBT 50 LA-1

Supply and Installation of 800W power amplifier each 400W X 2 Channel,power rating 2ohm,4 ohm,8 ohm etc. Make:Crown/Eq. Model No:XTi2002

Supply and installation of 12 channel analog audio mixer,3 band EQ,2 aux channels,2 mono channels,2 track audio control,XLR and jack main outputs.Make :Soundcraft

Supply and Installation of 1000W active speaker with stand for press. Make:EV/Eq. Model No:ZLX12P

Supply and laying of 2 core 1.5 sq mm Speaker Cable.

Supply and Installation of 17U floor mount heavy duty audio rack with lock and key facilities. Make:Valrack/Eq.

Supply and Installation of 3 KVA Servo Voltage stabilizer withOver and under voltage correction – automatically regulates in both conditions,Wide input voltage range for Indian conditions (140-260V). Accurate voltage control,No waveform distortion. Make :Studiomaster/Eq.

Supply and Installation of handheld wireless microphone with transmitter. Make: Shure/Eq. Model No:SLX 24/Beta 58

Supply and Installation of 18 inch condenser podium microphone with Base ON/OFF. Make:JTS/Eq.

Supply and Installation of Teak solid Wooden body Podium as per PWD standard. Make:Custom/Eq.

Supply and Installation of 15m microphone cable with XLR male and Female sockets. Make:Branded/Eq.

Supply and Installation of 24 port Fully managed Layer -2 switch. Make:D-Link/Eq.

Supply and Installation of 24 port Fully loaded patch panel. Make:D-Link/Eq.

Supply and Installation of RJ 45 & RJ 11 I/O,back boxes and face plates on wall. Make:D-Link/Eq.

Supply and Installation of 100 pair DB with module. Make:D-Link/Eq.

Supply and Installation of 10 pair DB with module. Make:D-Link/Eq.

Supply and Installation of 10 pair telephone cable in existing pvc pipe on wall and ceiling. Make:Finilex/Eq.

Supply and Installation of 2 pair telephone cable in existing pvc pipe on wall and ceiling. Make:Finolex/Eq.

Supply and Installation of cat6 cable in existing pvc pipe on wall and ceiling. Make:D-Link/Eq.

Supply and laying of 25mm dia 1 inch pvc pipe on wall and ceiling.

Supply and Installation of 55 inch LED TV with 4 nos HDMI port, USB, EP, clear+, netflix and other OTT apps supports etc. Make: Sony/Eq.

Supply and installation of 6U wall rack with power manager and all accessories.

Supply and Installation of 4 MP IP Indoor / outdoor bullet/dome Camera, 120 db WDR, 3.6 mm Fixed lens.Make:NEOS/Eq.

Supply and Installation of 8-port poE switch, which supports IEEE802.3 af/at poE standard. Make: D-link/Eq.

Supply and installation of 32 channel Network Video recorder , band width support 2 SATA HDDs up to 8 TB . Make :NEOS / Eq.

Supply and Installation of 8TB built in Hard Disc Drive. Make: Seagate/Eq.

Supply and Installation of 43 inch LED TV for CCTV camera monitors. Make:Sony/Eq.

Supply and Installation of 0.6 KVA UPS. Make:APC/Eq.

Supply and Installation of EPABX system with 4 P&T line 16 extension intercom system estension uoto 64 with 1 KVA UPS.

Supply and Installation of caller ID telephone instrument. Make:Beetel/Eq.

Supply and Installation of 1m patch cord. Make:D-Link/Eq.

Supply and Installation of 2MP IP PTZ Camera with 50 IR,Micro SD slot,IP67 without builtin mic and USB. Make:D-Link/Eq.

Supply and Installation of 98 inch 4K,Android-13, interactive touch Professional display with USb C,HDMI in & out with OPS etc. Make:UniQ/Eq.

Supply and Installation of 75 inch, 4K,Android-13, interactive touch Professional display with USb C,HDMI in & out with OPS etc. Make:UniQ/Eq.

Supply and Installation of 30m OFC HDMI cable with connectors. Make:Branded/Eq.

Supply and Installation of 1:4 HDMI splitter. Make:Branded/Eq.

Supply and Installation of DTH Recharge for one year. Make:D-Link/Eq.

Supply and Laying of RG6 coaxial cable for DTH connections. Make:D-Link/Eq.

Supply and Installation of Lap top with Processor: Intel Core i5-12450HX | Speed: 2.4GHz (Base) - 4.4GHz (Max) | 8 Cores | 12 Threads | 12MB Cache,Memory: 16GB RAM DDR5-4800 with wireless mouse,audio cable,1 year anti virus and mouse pad etc. Make:HP/Eq.

Supply and Installation of 24 channel audio splitter for press. Make:Stranger/Eq.

Testing and Commissioning of PA system,CCTV security camera,LAN net work system,EPABX Inercom system,Tata sky Super LNB 2.0 and other accessories etc

GST at 18%

PL Comm Infra LLP (BID ID -1229300)

GMS Elegant Builders I Pvt Ltd (BID ID -1229145)