Renovation of Net house Screening Facility Structure for Plant growth experiments and Construction of RCC drain, Stone pitching and Miscellaneous works at Hill Side at North site, BARC Trombay, Mumbai.

Amount

Dismantling stone slab flooring laid in cement mortar including stacking of serviceable materials and disposal of unserviceable materials within 200 m lead

Dismantling old plaster / skirting carefully , raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 100 m lead

Dismantling of RCC works carefully manually without damaging adjacent structures excluding cutting of reinforcement including stacking of steel reinforcement bars and disposal of unserviceable materials within 200 m lead as per direction of Engineer-in-charge

Lead charges for lead exceeding 2 km but not exceeding 3 km, by mechanical transport including loading, unloading, stacking/leveling etc.

Debris Beyond 2 Km but up to and including 3 km Note: The rates in respect of this item are applicable for NET quantities arrived at after making deduction for voids @ 30% from corresponding truck measurement.

Providing structural repairs in old damaged concrete structures/ surfaces with approved Polymer with following operations: 1) Removal of loose/Spalled or damaged concrete by chipping and cleaning the concrete surface and reinforcement steel with wire brush and with water 2) Cleaning the re bars with Acetone for complete rust removal and washing with water to make the surface clean. 3) Applying protective coat / bond coat using polymer and cement in the proportion of 1; 1.5 (1 part of polymer and 1.5 parts of cement in synthetic enamal paint like consistancy with brush 4) Reinstate the area with polymer modified mortar in layers of maximum 20 mm with the proportion of Cement 50 Kg : washed and dried river sand 87.50 kg ; silica sand 37.50 Kg. mixed with 10 litres of Polymer (or 1 Kg cement : 1.75 kg washed and dried river sand ; 0.75 Kg silica sand : 200 ml polymer) (5) If thickness of repair exceeds 20mm , after every 20 mm thick repair, bond coat as per 2 above to be applied and further thick of repair to be continued for each layer. This work is inclusive of all materials, labour, complete all as directed at site using approved polymer suitable for structural repair shall be used) Note: Scaffolding will be paid separately under relevant item

Providing and laying in position cement concrete of 1:3:6 (1 cement, 3 crushed sand, 6 graded stone aggregate of maximum size 20 mm) including consolidation, finishing, curing etc. complete as per specifications and drawings but excluding the cost of Form work shuttering, centering Complete at all levels

Providing and laying in position cement concrete of 1:2:4 (1 cement, 2 crushed sand, 4 graded stone aggregate of nominal size 20 mm) including consolidation, finishing, curing etc. complete as per specification and drawings but excluding the cost of Formwork shuttering, centering and steel reinforcement at all Levels

Providing and laying in position reinforced cement concrete (RCC) of grade M-30 using 20 mm maximum size aggregates and crushed sand of approved quality including admixtures of approved brand and quality (plasticizers or super plasticizer) if required, including weigh batching, mechanical mixing, transporting, placing, vibrating, consolidation, finishing, curing etc. complete but excluding the cost of centering, shuttering and reinforcement complete as per specifications. up to Plinth Level. Note : (i)The rates quoted for these items shall be inclusive of the cost of admixtures, trial mixes, testing (at site & at approved labs), etc. complete. (ii) Minimum cement content is given by table mentioned below:

Extra for RCC Using Ready Mix Concrete from outside project area including transporting and pumping from approved batching plants .

Providing, centering, shuttering Form work using steel plates, timber planks for all types of structures including necessary strutting, proping, staging, supports, bracings etc. and deshuttering the same after the specified time all as per drawings, specifications and as directed by the Engineer-in-charge at all levels- for sub structure.

Providing Reinforcement Steel for reinforced cement concrete at all levels including supplying, preparation of bar bending schedules, cutting, bending, transporting, fixing, tieing in position with PVC coated with 1.6 mm dia soft drawn annealed G.I binding wire, all labour charges, cost of cover blocks in specified grade of concrete etc. etc. complete including cost of binding wire, complete as per specifications and drawings. - Steel supplied by the contractor. Using TMT bars of specified grades all dia bars. TMT bars of approved manufacturers to be supplied by the contractor - confirming to IS:1786. Note: Cover blocks shall be of same grade of concrete

Providing and fixing SS-304 grade crimpnet mesh of size 25mm x 25mm and wire diameter upto 3mm on existing structural steel members by using SS-304 grade flats/angles etc including all welding,SS bolting, buffing etc. complete at all levels and locations as directed by the Engineer-in Charge complete

Supplying , cutting to shape and fixing 110 mm diameter UPVC Pipes as per IS 4985 in RR Masonry/ RCC walls for weep holes complete all as per drawings and as specified at site.

Providing 20 mm thick plastering using Ready mix external plastering compound of approved make for external faces of brickwork / concrete surfaces including preparation of the surface, curing, cleaning scaffolding up to 10 metres height complete.all as per specifications including forming drip moulds wherever necessary and as directed by the Engineer-in-charge

Providing, applying and finishing walls with two coats of premium fine textured exerior paint of required shade over new work including base coat of water proof cement paint, preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge - On Plain plastered / concrete sufaces

Providing and Painting with Epoxy PU paint On STEEL surfaces using 2 coats of (120 Micron dry film thickness) Epoxy PU high build coating as finishing coat over a priming coat of High Build epoxy primer of 50 micron thickness over steel surfaces at all locations prepared and applied as per manufacturer' specifications including preparation of surface by cleaning with wire brush and rubbing, scraping , applying sand paper , making free of Rust, dust, dirt etc. filling the holes, joint, cracks if any using epoxy putty complete. all as per manufacturers technical data and as directed at site to achieve minimum overall dry Film thickness of 170 micron (50 Micron primer Coat + 120 micron finishing Coat).

Providing and Fixing in position 6 mm thick solid clear (Translucent) Polycarbonate sheet of approved make including cutting, fixing on existing supports by Replacing damaged panels and sealing the joints with silicon sealent with necessary stainless steel fastners, scafffolding if necessary complete all as directed by Engineer in charge. Note : Aluminium section / strip will be paid in relevant item

Providing and Fixing Homogeneous 2.00 mm thick PVC sheet / tile in flooring and skirting of approved make in approved pattern on a smooth and damp proof base using rubber based adhesive of approved quality and manufacturer including, levelling small undulations with plaster of paris if required , rolling with light wooden roller weighing about 5 kg all complete as directed by Engineer-in-charge in approved colour and shade

Providing Structural steel work using angles, channels, joists and other sections, welded and / or bolted in built up sections for trusses, structural steel floors, frame works, monorails and other structures including supplying, cutting, welding, fabricating, hoisting, fixing in position, applying a priming coat of approved steel primer etc. complete all as per specifications, drawings and as directed by the Engineer-in-charge. Up to and including 300 mm Joists, 350 mm channels, and below sections using materials produced by approved make and manufacturers. All test reports to be provided along with the supply of the materials confirming to IS:2062. Note : (1) Welding weights, connections, bolts and nuts shall not be measured for payment, but the cost of which shall be deemed to have been included in the rate. Rate is also inclusive of all consumables like welding electrodes and tools and tackles etc. (2) All holes will be made by drilling only. Gas cutting of holes will not be permitted. (3) Electrodes manufactured by approved manufacturer shall be used. (4) Edges of plates shall be grinded to uniform smooth finish. (5) The contractor shall supply documentary evidence of purchase of steel, Test certificate from approved manufacturers and also third party testing from approved laboratories with out any extra cost.

Providing Structural steel work in M.S Plain Plates and chequrred Plates for Embedded Parts, Trench Covers, Connection plates etc. including cutting, hoisting, fixing in position and applying a priming coat of approved zinc chromate steel primer etc.including cost of structural steel Plates, welding all labour charges etc. complete as per drawings and specifications, using materials of approved manufacturers. All test reports to be provided along with the supply of the materials Note: (1) Structural steel required for the work shall not be supplied by the Department and the contractor has to procure the same. (2) Welding weights, connections, bolts and nuts shall not be measured for payment, but the cost of which shall be deemed to have been included in the rate. (3) All holes will be made by drilling only. Gas cutting of holes will not be permitted. (4) Electrodes manufactured by approved make shall be used.

Supplying man power along with necessary spades, shovels, punjas, ropes, small special spades, rain coats, broom, mop etc, minimum two labours per day and maximum any number of labour as and when decided by Engineer Incharge to work for eight hours per day to carry out the cleaning work, loading work etc as directed by Engineer Incharge.

Providing and fixing Minimum 15mm thick gang saw cut mirror polished Granite (premoulded and prepolished) machine cut Granite (Moon white shade or as approved) for flooring/skirting in lobby, passage, staircase (Tread and Riser), kitchen platforms, vanitiy counters, Wash basin Counters, Door Frames, window sills, facias and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (using coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing the edges to give high gloss finish etc. complete at all levels

Providing and applying wall painting two coats on new work with premium plastic emulsion paint of approved brand to give an even shade, including a coat of approved cement primer, including preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge

Providing and applying white cement based wall putty of approved make over concrete or Plastered surface up to 3 mm thick to get uniform surface free from undulation including cleaning complete all as directed by the Engineer-in-charge

Providing and applying Polyurethane coating for external application in two coats on stone masonry/ brick masonry with polyurethane paint. Polyurethane for external application system consists of 4 part of Polyurethane rasin : 1 Part polyurethane Hardener by weight, as per approved manufacturer's specifications, including preparation of surface by cleaning with water jet,removing loose material, scaffolding, etc. complete as directed by Engineer-In-Charge. Note : (1) Application of each coating requires gap of 12hrs. (2) Net Area will be measured for payment. (3)Waterproofing guarantee for a period of 10 years shall be submitted for this item. (4) Any repair of joints, pointing, grouting required shall be done before application of above Polyurethane coating and shall be paid separately.

Providing and fixing 25 mm thick Colour PVC Integral Foam Sheet door shutters for flush door of approved colour, approved make, design, colour and fixing with 4 Nos 100 mm (ISI marked) stainless steel hinges, Fixing of Stoppers, tower bolts, baby latch, aldrop, handles etc. wherever required with S.S. screws. etc (Stopper, Tower bolt, Baby latch, Aldrop, Handels etc Shall be supplied by department) etc. complete as per specifications and as directed by Engineer-in-charge. Note: PVC integral foam sheet used in door shutter shall satisfy the following technical parameters : 1. Density : Min. 0.55 g/cc, 2. Hardness (Shore 'D'): min. 55, 3. Water absorption : max. 1 %, 4. Tensile strength : min. 10 MPa, 5. Elongation : min. 15 %, 6. Flexural Strength: min. 20 MPa, 7. Compressive Strength at 10% Deformation : min. 3 MPa, 8. Vicat Softening Temperature: more than 75 Deg Celcius 9. Flammability: classification B : S3 : D0 (to be tested as per NF EN 13501-1 standard)

Providing and fixing stainless steel tower bolts of size 150 X 12 mm of approved make with necessary screws etc.all as per specifications and as per drawings

Providing and fixing IS:12817 marked stainles steel butt hinges of size 100 x 60 x 2.5mm (heavy weight) of approved make with stainless steel screws etc. complete as directed by the Engineer-in-charge

Providing and fixing aluminium hanging heavy quality floor door stopper ISI marked with twin rubber stoppers, anodised transparent or dyed to required. colour or shade with necessary screws etc. complete.

Providing and fixing brass mortise latch and lock of approved make with 6 levers and a pair of lever Brass handles with necessary screws etc complete suitable for fixing in wooden / steel/ FRP/ doors as per specifications.

Providing and fixing Aluminium Grill 10 mm thick in natural Silver anodising of min 15 Microns with opening size of 80 mm x 66 mm and Minimum weight of 3.13 Kg/ Sq.M including providing and fixing Suitable 'F' / 'H' section outer frame and mullion fixing with screws complete all as per specifications and as directed at site by the Engineer-in-Charge .Aluminium alloy shall be of 6063-T6 with Yield strength of minimum 6.5 kg/ sq.mm. meeting all the technical specifications as per relevant codes and standards. Note: Tentative / suggested make for guidance of bidder(s) - M/s "DECO GRILLE" make, Model No. DG- 102

Providing and fixing glazing in aluminium doors, window, ventilator shutters and partitions etc. with clear float glass panes of 5.00 mm thickness, with PVC / Neoprene gasket etc. complete as per the architectural drawings and directions of the Engineer-in-charge (Cost of snap beading shall be paid in basic item)

Providing and fixing anodized aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / Z sections and other sections of approved make conforming to IS 733 and IS 1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically whereever required including cleat angle, aluminium snap beading for glazing / panelling, C.P brass / stainless screws all complete as per drawings and and directions of Engineer-in-charge including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required filling the gaps using silicon grout sealent etc. (fittings glazing and panelling shall be paid for separately). Anodized Aluminium sections (Minimum anodizing thickness of 15 micron) Note: The contractor shall provide screws, MS tie rods etc. No extra payment will be made for it.

Extra over item no 33 for colour anodizing

Providing and fixing approved quality stain less steel body roller wheels of approved make for sliding shutters

Providing and fixing approved quality and shape star locks cum handle of approved make for sliding shutters

Providing, painting,finishing walls with two coats of anti-algae, weather proof acrylic smooth emulusion paint of approved make with silicon additives on sand face plaster/ plain plaster & concrete surfaes of required shade over new work over a base coat of exterior cement primer including preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge.

From 0.00 to 1.50 m depth from Average Ground Level

From 1.5 to 3.0 m depth from Average Ground Level

From 3.0 to 4.5 m depth from Average Ground Level

Labour charges for murum filling under floors of specified thick in layers of not exceeding 150 mm thickness including consolidation etc. complete (using murrum available at site)

Providing and constructing Random Rubble masonry using approved Rubble stone in super structure (above plinth) in C.M 1:6 (using crushed sand) including raking out joints or simultaneous flush pointing above ground level / plinth level and up to and including 20 m height including scaffolding, curing etc. complete as per drawings and specifications.

Providing, fabricating and erecting in position CRIMPNET GATE with G.I. tubular frames, 50mm *8g G.I. crimpnet welded on 38 mm i/d G.I. pipes with angle iron frame, m. s. flat beading to hold crimpnet, m.s. channel supports including pivot type hinges, locking arrangements, tower bolts, embedding channel posts in cement concrete 1:3:6 including cost of scaffolding, excavation , pcc, form work and disposal of surplus soil, Painting the gates and all steel works with two coats of approved paint over a coat of primer complete generally as per specifications and drawings. ( Structural steel members will be measured under relevant item)

Providing& fixing G.I. pipes medium variety ( Class B ) for Crimpnet Gate etc. including cutting of pipes as required, bending & welding including painting with two coats of synthetic Enamel paint over a coat of steel primer etc. complete.

Supplying & fixing in position 50mm * 8 gauage G. I. Crimpnet welded to pipes with G. I. pipe / Angle frame using M.S. Flat beading of 40*8 mm to hold crimpnet including cost of M. S. flats, scaffolding all material & labour etc. complete as per specifications. ( Area of CRIMPNET Mesh alone will will be measured for payment )

Providing and fixing dry stone pitching 22.5 cm thick laid in required profile with hammer dressed stones having no side less than 15 cm, with minimum depth of 20 cm including preparing the bedding surface etc. all complete as directed by the Engineer-in-charge

Providng and fixing at and near ground level precast cement concrete 1:2:4 in kerbs, edgings etc. as per approved patterns and setting in position with C.M 1:3 (using crushed sand) including consolidation, curing, cost of required centering, shuttering, finishing smooth with 6 mm thick cement plaster 1:3 (using crushed sand) on exposed surfaces complete as per specifications and as directed by the Engineer-in-charge

Providing and laying non pressure NP2 class RCC Hume pipes of approved make, with collars jointed with stiff mixture of cement mortar in the proportion of 1:2, laying to the levels, slopes and as per the drawings and specifications and as directed by the Engineer-in-charge including testing of joints etc. complete.

300 mm Dia RCC Hume pipe class NP2

Providing and constructing Brickwork in cement mortar 1:4 using crushed sand with Flyash / Flyash Lime bricks with minimum 70 kg / Sq. cm strength of approved make and size in sub-structure including, scaffolding, raking out joints, curing, cleaning complete all as per specifications and drawings.

Supplying , cutting to shape and fixing 110 mm diameter UPVC pipes as per IS 4985 in RR Masonry/ RCC walls for weep holes complete all as per drawings and as specified at site.

Demolishing dry stone pitching in floors, drains etc. including stacking serviceable materials and disposal of unserviceable materials within 200 m lead

Labour charges for dry stone pitching 22.5 cm thick by using good soling stones available at site, preparing the surface complete

Dismantling doors, windows and clear storey openings (steel / wood) shutter including chowkhats, architraves, holdfasts etc. complete and stacking within 100 m lead (full windows) of area 3.00 Sq.M and below

Dismantling doors, windlows and clear storey windows (steel / wood) shutter including chowkhats, architraves, holdfasts etc. complete and stacking within 100 m lead (full windows) Of area beyond 3.00 Sq.M

Taking out doors, windlows and clear storey openings (steel / wood) shutter including stacking within 100 m lead (only shutters) Of area 3.00 Sq.M and below

Taking out doors, windlows and clear storey openings (steel / wood) shutter including stacking within 100 m lead (only shutters) Of area beyond 3.00 Sq.M

Providing and fixing GI chain link fabric fencing made of GI wire of dia 4 mm of required width in mesh size 50 x 50 mm including strengthening with 2mm dia wire or nuts, bolts and washers as requeid complete as per direction of Engineer-in-charge.

Providing and fixing concertina barbed tape coil of follwoing dia. made from M.S galvanized ribbon tape of 0.5 mm thickness, 19 mm width stretching the coil to 9 m approximate, fixing the coil with clips between "Y" armed and MS angle posts 2.44 m high from ground level, including supplying and fixing MS galvanized clips etc. complete as per manufacturer's specification and including painting by dipping method the concrtina tape coil with two coats of synthetic enamel paint of approved shade and make over a coat of approved primer at fabrication shop, before bringing the material to the site and fixing in position etc. complete as directed by the Engineer-in-charge

450 mm Dia Concertina coils

Providing and laying minimum 25 mm thick uniform shade Kotah stone flooring over 20 mm thick (Avearge) base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing in minimum three levels to obtain mirror polish complete with base cement mortar 1:4 (using crushed sand) all as per specifications, patterns and drawings complete.

Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M-30 grade made with strong vibratory compaction and approved size, shape, design laid in required colour and pattern over and including 50 mm thick compacted bed of crushed sand, filling the joints with crushed sand etc. all complete as -per the direction of the Engineer-in-charge

Providing and fixing 2 Hour Fire rated metal framed partions of Non Load bearing type (98 mm over all Thickness) using Floor / ceiling Channels of 50 x 32 x 32 x 0.55 mm sizeat Top & bottom perimeter of the Partiotion and Studs of 48 x 50 x 48 x 0.55 mm Vertically at maximum of 610 mm centre to centre and Bracing members of 45 x 15 x 15 x 0.90 mm at horizondal at all board joints with 2 Boards of 12 mm thick Calcium silicate board of approved make on both sides with self drilling screws to metal frame at 200 mm C/C. All cavities in the partition shall be filled with CERAMIC wool of 50 mm thick of Densisty 64 Kg / Cu.M. All joints shall be filled & finished with Joining Compound of approved make and 48 mm wide fiber tape to get seamless finish. A coat of Cement primer, Putty and finished with 2 coats of Acrylic Emulsion paint of approved make complete all as per the drawings/ fabrication drawings as per manufacturers specification and as directed at site by the Engineer-in-charge Tentative/Suggested make/ model of Calcium Silicate board and jointing compound for guidance of bidder(s) : M/s HILUX

Dismantling brick work in Cement mortar carefully without damaging adjacent structures including stacking of materials and disposal of unserviceable materials within 100 m lead as per direction of Engineer-in-charge

Providing, supplying, cutting, welding, fabricating, hoisting and fixing in position structural steel members like trusses, purlins, posts etc. using MS hollow / circular / square / rectangular tubular sections including appling a coat of Zinc chromate primer of approved make all as per specifications, drawings and as directed by the Engineer in charge

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing & staircases railing including applying a priming coat of zinc chromate steel primer etc. complete as per specifications using M.S tubes of ISI marked (Medium) of specified diameter and thickness

Dismantling steel work in single sections including dismantling and stacking within 100 m lead In R.S Joists, Angles etc.

Providing and fixing aluminium aldrops of size 250 X 16 mm ISI marked anodised transparent or dyed to requried colour or shade with necessary screws, bolting from rear side complete as per specifications and as directed by the Engineer-in-charge

Providing and constructing brickwork in cement mortar 1:6 using crushed sand with Flyash/ Flyash Lime bricks with minimum 70 kg/ Sq.cm strength of approved make and size in super structure above plinth up to and including Floor II level including, scaffolding, raking out joints, curing, cleaning complete all as per specifications and drawings

Providing 15 mm thick plastering using Ready mix internal plastering compound of approved make for internal faces of brickwork / concrete surfaces including preparation of the surface, curing, cleaning, scaffolding complete all as per specifications and as directed at site by the Engineer-in-charge

Providing and fixing IS: 3564 marked aluminium die cast body tubular type universal hydraulic door closer of approved make with necessary accessories and screws etc. in wooden doors / steel doors with necessary bolts & nuts complete as per specifications and as directed by the Engineer-in-charge.

Providing & supplying of Pick-up Van / Utility Van for various areas for the requirements arising from time to time inside and outside BARC. The Pick-up Van / Utility Van of five seaters capacity with the back side provision for transporting/ shifting of various construction / maintenance materials, machinaries and tools etc. and for other works including Driver as assigned and directed by Engineer-in-Charge. (8Hrs. a day or 80 km max as per certification of Engineer-in-Charge). Conditions: 1. The above rates shall be inclusive of cost of supply of Pick-up Van / Utility Van, Fuel, wages of Drivers and other consumables etc. 2. The Reporting time at the place of duty / as instructed by EIC shall be considered for the billing / measurement / payment. 3. In case the pick up van is parked inside the BARC premises then the reporting time of the driver to EIC shall be considered for the billing/ measurement/ payment. 4. Break Down Hours as per actuals and Lunch break (30 min.) timings shall not be considered for payment. 5. Fraction of hours shall be rounded off to nearest half an hour at the time of preparing the Running / final bills 6. BARC being a strategic Organisation, the driver should have good credentials and shall have valid PVC, driving license and address proof. They should be in a position to understand Hindi / English / local language. 7. The make and model of the vehicle should be of not more than 8 years old, roadworthy all valid documents. 8. The vehicle shall be maintained in good running condition with good upholstery, fitness, good tyres and shall commensurate with the image of BARC. The tyres of the vehicles shall be replaced periodically and always with tyres of good condition. 9. The vehicle should be free from all sorts of defects and will be subjected to inspection by a representative of BARC whose decision is final and binding as regards suitability of that particular vehicle. 10. The vehicle should be transport vehicle and preferably in white colour with a board "ON GOVERNMENT OF INDIA DUTY". 11. The cost of POL, maintenance of vehicle including replacement of parts, wages of driver, Motor Vehicle taxes, comprehensive insurance, etc. shall be payable by the Contractor and BARC shall have no liability towards usage of the vehicle. 12. The cost of damages to any Government movable/immovable property in and around the site shall be entirely borne by the Contractor. 13. The rates are inclusive of all taxes if any, including Goods & Service taxes (GST). 14. The contractor shall arrange adequate insurance coverage for his personnel. Department shall not be responsible for any liability arising out of any accident / injury caused to the driver while executing the job. 15. The contractor shall follow minimum wages act and other rules of Government of Maharashtra. 16. No revision of price shall be entertained during the period of contract. 17. Hours more / less than 8 Hrs. a day will be paid / deducted on pro-rata basis. 18. In case of absence of Driver/vehicle for entire week, a penalty of Rs. 3000 /- will be imposed for that week.

Providing and fixing 4 Lever Mortice Lock of approved make suitable for aluminium sections

Dismantling plain cement concrete manually / by mechanical means carefully without damaging adjacent structures including disposal of debris within 200 m lead as per direction of Engineer-in charge

Supplying, stacking and laying of 230 mm thick rubble soling stones as under floor base including packing with smaller stone and compacting, ramming including spreading and consolidation of blinding material, moorum etc. complete all as per specifications and as directed by the Engineer-in-charge

Providing , Laying , jointing, fixing and testing Heavy quality (C- Class) Galvanised Iron pipes and ISI marked fittings like, tees, elbows, bends, unions, nipples,reducers etc. as required for the work, including testing the pipes and fittings for 10.00 Kg / Sq.Cm hydralic pressure with a minimum period of two hours duration with clean water, including cutting , threading, jointing with hemp yarn, white lead, jointing Teflon tape, exposed / concealed by chasing walls and making good by filling with concrete 1:3:6, complete all as per specifications and drawings, including two coats of anti corrosive bitumastic paint for all concealed lines / two coats of synthetic enamel paint for all exposed lines all as directed by the Engineer-in-charge. Pipes with exclusive use of TATA make C-Class pipes.

25 mm dia G.I pipe

40 mm dia G.I pipe

Providing & fixing in position heavy pattern screw down gun metal gate valve with handles and wheels of approved make including testing for 10Kg/cm2 pressure with clean and potable water with a minimum testing duration of two hours etc.as per specification and as directed by the Engineer-in-charge

Providing and fixing C.P brass bib cock of heavy quality of specified / approved make as per specifications and as directed by the Engineer-in-charge

15 mm dia bib cock of approved type and make

Making soak pit of 2.5 m diameter and 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design and direction of Engineer-in-charge With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing square mouth S.W. gully trap complete with CI grating brick masonry chamber with water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.5 kg and frame to be not less than 2.70 kg as per standard design

150 x 100 mm size gully trap "P" type

Providing and fixing Brass 15 mm C.P presstomatic series auto shut urinal flush cock of approved make and quality

Providing and fixing PVC low level / high level flushing cistern 10 litre capacity of approved make in white colour with flush pipe with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures etc. complete as per specifications and as directed by the Engineer-in-charge.

Providing SFMC Micro concrete using 100% SFMC for strengthening of structural members including mixing, pouring, curing as per manufacturer specifications and as directed by the Engineer-in-charge

Supplying and installation of drain cleaning rod set for cleaning pipes of diameters ranging from 100mm to 600mm, as per following specifications including complete cleaning kit comprising of Sand driller, rod spanner,flat auger, Rod tightener, Rod turner; complete all as directed by the Engineer-in Charge.

Metro glass

SWASTIK ELECTROTECH PVT LTD