Carrying out short term measure for rectification of blackspot no. 051 from Nayagola petrol pump to Gurod road km. 4 to 4.05 of Vidisha -Kurwai NH-146 in the state of Madhya Pradesh

Amount

Short Term Estimate Nayagoal PP to Gurud Road (Vidisha -Kurwai NH-146)

Excavation in Soil using Hydraulic Excavator and Tippers with disposal upto 1000 metres. Excavation for roadwork in soil with hydraulic excavator i/c cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location with all lifts and lead upto 1000m as per relevent clauses of section-300 of specification. Earthen Shoulders

Embankment Construction with Material Obtained from Borrow Pits Construction of embankment with approved material having CBR>7 obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-1, 300-2 and as per relevent clauses of section-300 Note :- This item can be executed only after prior written approval by C.E.

ROAD FURNITURE

(a) ROAD MARKING Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes all complete as per clause 803 of specifications. (a) Edge Line Marking

Painting Lines, Dashes, Arrows etc on Roads in Two Coats on Old Work Painting lines, dashes, arrows etc on roads in two coats on old work with ready mixed Grade-I road marking paint (cold applied reflective paint)confirming to IS: 164 on bituminous surface,concrete i/c cleaning the surface of all dirt, dust and other foreign matter, demarcation at site and traffic control. (i) Over 10 cm in width

Transverse Bar Marking

Painting Speed Breakers

Road Markers/Cat Eye's Road Stud with Lense Reflector Providing and fixing of road stud 100x 100 mm, die cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling hole 30 mm upto a depth of 60 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS 873 part 4:1973

(b) At no overtacking zone (at centre line & edge)

(b) Road Sign Boards Retro- reflectorised Traffic signs Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign board as per IRC 67-2010 made of high intensity Micro-Prismatic Grade Sheeting (Type XI) vide clause 801.3.3 fixed over Aluminium composite material sheet with thermoplastic core of Low density polyethylene (LDPE) between two thick skins/sheets of aluminium with overall thickness of 4mm and aluminium skin of thickness 0.3 on both side, the ACM shall conform to Table 800-1 of specification and High Intensity Micro Prismatck Grade Sheeting shall conform to Table 800-3 of specification. The printing on the high intensity grade sheeting shall conform to Clause 801.3.7 with water based latex optimized transparent ink as specified by the sheeting manufacturer, supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to ground by means of properly designed foundation with M15 grade concrete 450x450x600mm The ACM sheet shall be fixed to the post with four minimum four number breakaway bolts.

(ii) 60 cm equilateral triangle

(iii) 60 cm circular

vi) 60 cm x 60 cm square

(vii) 90 cm high octagon

Direction and Place Identification signs with size more than 0.9 sqm size board. Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign board as per IRC 67-2010 made of high intensity Micro-Prismatic Grade Sheeting (Type XI) vide clause 801.3.3 fixed over Aluminium composite material sheet with thermoplastic core of Low density polyethylene (LDPE) between two thick skins/sheets of aluminium with overall thickness of 4mm and aluminium skin of thickness 0.3 on both side, the ACM shall conform to Table 800-1 of specification and High Intensity Micro Prismatck Grade Sheeting shall conform to Table 800-3 of specification. The printing on the high intensity grade sheeting shall conform to Clause 801.3.7 with water based latex optimized transparent ink as specified by the sheeting

manufacturer, supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to ground by means of properly designed foundation with M15 grade concrete 450x450x600mm. The ACM sheet shall be fixed to the post with four minimum four number breakaway bolts.

Parapet wall RCC-M20 Concrete :- Furnishing and Placing Reinforced/Prestressed cement concrete in super-structure as per drawing and Technical Specification and as per relevant clauses of sections 1500, 1700 and 2300 in A RCC Grade M20

Parapet wall PCC. Plain/Reinforced cement concrete in sub-structure complete as per drawing and technical specifications A PCC Grade M15

Road Delineators Supplying and installation of delineators (road way indicators, hazard markers, object markers), 80-100 cm high above ground level, painted black and white in 15 cm wide stripes,fitted with 80x 100 mm rectangular or 75 mm dia circular reflectorised panels at the top, buried or pressed into the ground & confirming toIRC-79 and the drawings.

On both side of CD

Supplying & fixing i/c maintenance LED Solar Blinkers mounted on steel pole to guide on varies vehicle driver of fourth coming junction & accident zone area manufacture using superior grade battery, solr panel & other panel, clearly visible enhanching road safety fogg, rain, night time and other adverse weather condition.

At Junction