CWEAFJ-21/2021-22 SPECIAL REPAIR TO CERTAIN QUARTERS AT AF STN JAMMU.

Amount

B/R Portion

Providing and injecting chemical emulsion for Post Construction Anti Termite Treatment along external wall below concrete or masonry apron using chemical emulsion @ 0.675 liters per hole including drilling and plugging holes etc. in apron complete all as specified and directed.

Post Construction Anti Termite Treatment of soil under existing floors using emulsion at the rate of one litre per hole 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 to match with the existing floors complete all as specified and directed.

Post Construction Anti Termite Treatment by injecting at points of contact of wood work by chemical emulsion in oil or kerosene based solution @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and directed.

Demolition of brick work or stone / boulder masonry built in cement mortar including all quoins, arches, pillars etc all as specified.

Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6, complete all as specified and directed.

Brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4, complete all as specified and directed.

Precast cement concrete louvers and Jallies 60mm thick (measured solid), type B-0 1:2:4 using 12.5 mm graded crushed stone aggregate set in cement mortar 1:4, complete all as specified and directed.

Demolition of Reinforced cement concrete of any description and in any position and removing rubbish from the site, complete all as specified and directed.

Reinforced Cement Concrete type B-1 1:2:4 using 20mm graded crushed stone aggregate as in slabs, roof projection etc., complete all as specified and as directed.

Formwork to chullah hoods, chajjas, troughs and similar items including edges not exceeding 200mm thick with rough finished flat surface of concrete, complete all as specified and as directed.

TMT bars 10mm dia and over, cut to length bent to shape including binding with MS annealed wire of dia not less than 0.90 mm, complete, all as specified and as directed.

TMT bars 6 to 8mm dia, cut to length bent to shape including binding with MS annealed wire of dia not less than 0.90 mm, complete, all as specified and as directed.

Taking down cement plaster on bricks or stone wall/ceiling decayed surfaces of concrete from roof projection or RCC chajjas etc. including racking out joints, hacking for key, scrubbing down with water etc., complete all as specified and directed.

Rendering 15mm thick in cement mortar 1:4 on brick work or concrete surfaces, mixed with integral water proofing compound, finished even and smooth without using extra cement, complete all as specified. Note : Integral Water Proofing Compound shall be measured and paid separately.

Supply only Liquid Water Proofing compound all as specified and as directed.

Rendering 15mm thick in cement mortar 1:6 on brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and as directed.

Rendering 10mm thick in cement mortar 1:3 in Fascia or edging of Chajjas, Ceiling and Roof projections etc., including taking out pealed off plaster / concrete and making the line in true shape and finishing the surface without using extra cement, complete all as specified and as directed.

Wire netting of galvanised steel 0.71mm dia wire, and mesh size 12mm fixed with tinned tack of wire staple complete all as specified and directed.

Demolition of cement concrete in ground floors and paving (un-reinforced) not exceeding 15cm. thickness, below or above ground level, complete and removing rubbish from the site, complete all as specified and directed.

Demolition of cement concrete in ground floors and paving (un-reinforced) exceeding 15cm. thickness, below or above ground level, complete and removing rubbish from the site, complete all as specified and directed.

PCC 1:4:8 type D-2 using 40 mm graded crushed stone aggregate 75mm thick as in sub base, floors, pavings finished even and fair complete all as specified.

75mm thick, plain cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection etc., finishing surface even and fair without using extra cement including making joints with bitumastic filling in proportion of bitumen and sand 1:3 by weight complete as specified and directed. Note : The concrete shall be laid at a stretch not exceeding 3.0m in length and joint shall be made at every turning / corners, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed.

25mm thick PCC 1:2:4, type B-0 (using 12.50mm graded crushed stone aggregate) as in floor, finished even and fair to receive floor finishes, complete all as specified and as directed.

40mm thick, plain cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in floors etc., finishing surface even and smooth without using extra cement, complete as specified and directed.

Non-skid coloured glazed, joint free, ceramic tiles of any shade and any pattern of size (Pattern consists combination of two or more tiles) 400mm x 400mm x 7mm thick, over and including 15mm thick screed bed in CM 1:4 as in floors etc. jointed in neat cement slurry and pointed in coloured cement to match coloured tiles, complete all as specified and directed.

Non-skid coloured glazed, joint free, ceramic tiles of any shade and any pattern of size (Pattern consists combination of two or more tiles) 400mm x 400mm x 7mm thick, over and including 10mm thick screed bed in CM 1:4 as in skirtings etc. jointed in neat cement slurry and pointed in coloured cement to match coloured tiles, complete all as specified and directed.

Glazed ceramic coloured, joint free, wall tiles in any type and in any pattern (Pattern consist of combination two or more different colour tiles etc.) in vertical surfaces of size 450mm x 300mm x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick backing coat in CM 1:4, finished fair to received the tile, complete all as specified and directed.

Granite Stone, 20mm thick, (table rubbed and polished) in platform bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone over and including 15mm thick screed bed in cement mortar 1:4 finished fair to received the granite including rounding the exposed edges, complete all as specified and directed.

Taking down chowkhats with shutters (without taking off shutters from the frames not exceeding 1.50 Sqm each, including cutting holes for taking out hold fasts or dismantling brick work and making good the disturbed surface complete all as specified and as directed.

Taking down chowkhats with shutters (without taking off shutters from the frames exceeding 1.50 Sqm and not exceeding 4.00 Sqm each, including cutting holes for taking out hold fasts or dismantling brick work and making good the disturbed surface complete all as specified and as directed.

Pressed steel frame for door with one or more rebates including necessary lugs, fixing lugs hinges, lock strike plate etc. of size 105mm x 60mm and made of 1.25mm thick MS sheet, complete all as specified and directed including necessary welding complete and including medium weight 03 No's of MS butt hinges of size 75mm / 100mm / 125mm and 01 No 50mm Size of medium weight MS butt hinge, complete all as specified and directed.

Pressed steel frame for door with one or more rebates including necessary lugs, fixing lugs hinges, lock strike plate etc. of size 125mm x 60mm and made of 1.25mm thick MS sheet, complete all as specified and directed including necessary welding complete and including medium weight 03 No's of MS butt hinges of size 75mm / 100mm / 125mm and 01 No 50mm Size of medium weight MS butt hinge, complete all as specified and directed.

PCC 1:3:6 type C-0 (using 12.5mm graded crushed stone aggregate) as in back filling of pressed steel frames and in bed block for holdfast etc. similar work etc. complete all as specified and directed.

Small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like including all necessary labours, articles not exceeding 200 Cu.cm each made out of 1st class hardwood complete all as specified and as directed.

40mm thick factory made Flush Shutters, solid core construction, with block board core and pre-laminated particle board, exterior grade, prelaminated both sides with decorative choice laminations complete as specified and directed.

35mm thick, 1st Class hard wood, factory made, glazed and skeleton shutters open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats, complete all as specified and as directed.

Factory Made UPVC white colour sliding window three track area not exceeding 2.00 Sqm each made of extruded profile with wall thickness of 2.3mm (+0.2mm) window profile with hollow section with multi chamber, frame (88mm x 52mm) sliding sash (42 x 67mm) sliding mesh sash (42mm x 57mm) sliding interlock (one vertical length in each shutter) (45.5mm x 28mm) glazing bead (24.5mm x 16mm) will be mitered cut and fusion welded at all corners including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, epdm gasket 1.2 + 0.2mm thick galvanised steel frame (30 x 21.5mm) 02 Nos, sliding sash (30 x 18mm), sliding mesh sash (26mm x 10mm), profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners. hardware : Touch lock of zinc alloyed (white powder coated) steel roller system,

Factory made UPVC white colour sliding window two track area not exceeding 2.00 Sqm each made of extruded profile with wall thickness of 2.3mm (+0.2mm), Window profile with hollow section with multi chamber, frame (60mmx62mm) sash (42 x 67mm) sliding interlock (one vertical length in each shutter) (45.5mm x 28mm), glazing bead (24.5mm x 16mm) will be mitered cut and fusion welded at all corners including railing of holes for fixing hardware and drainage of water etc, making arrangement for fixing of hardware, epdm gasket 1.2+ 0.2mm thick galvanised steel frame (30mm x 21.5mm), sash (30mm x 18mm), profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners. hardware : (touch lock of zinc alloyed (white powder coated)

PVC hollow door frame of size 50mm x 47mm with a wall thickness of 5mm made out of extruded 5mm thick rigid PVC foam sheet, mitred cut at two corners and joined with two nos of 150mm long brackets of 15mm x 15mm MS square tube. The two vertical door profiles are to be reinforced with 19mm x 19mm MS square tube of 19 gauge, EPDM rubber gasket, weather seal to be provided through out the frame. The doorframe shall be fixed to the wall using 65/100mm long MS screws through the frame using PVC fasteners. A minimum of four nos of screws to be provided for each vertical member and minimum of two nos of screws for each horizontal member complete as per manufacturer’s specification and drawing and as directed.

Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 4-5mm thick Moulded PVC Sheet on the front face & 4mm plain colour PVC sheet on back face, either particle board core supplying & fixing in frame at site as per specification and drawing complete all as specified and as directed.

Mild steel framed works such as grills, framed guard bars, etc. and similar work conforming to Fe-410-O or Fe-310-O grade, including bending, cutting and welding as required, complete all as specified and as directed.

Butt hinges, medium weight, Stainless Steel, 75mm size, complete all as specified and directed.

Butt hinges, medium weight, Stainless Steel, 50mm size, complete all as specified and directed.

Stainless Steel, sliding door bolt with hasp, staple (bolt type) 250mm, and fixing clips of sheet and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

Stainless Steel barrel tower bolt complete of size 200mm long complete all as specified and directed.

Stainless Steel barrel tower bolt complete of size 150mm long complete all as specified and directed.

Stainless Steel handle complete of size 150mm long complete fixed in repairs complete all as specified and directed.

Stainless Steel handle complete of size 125mm long complete fixed in repairs complete all as specified and directed.

Stainless Steel handle complete of size 75mm long complete fixed in repairs complete all as specified and directed.

Brass 300mm spring for door, ordinary Rat Tail Rod pattern springs, including roller and roller plate complete fixed in repairs complete all as specified and directed.

Floor Door Stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor 150mm complete all as specified and directed.

4mm thick sheet glass ordinary quality and glazing with oil putty, wooden beads or fixed in aluminium window shutter in squares not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

4mm thick figured glass, pin head type and glazing with oil putty, wooden beads or fixed in aluminium window shutter in squares not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

Stainless Steel Wire Cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed.

Dismantling boarding, any description, fixed in any position with screws complete all as specified and directed.

Block Boards, grade-2 quality, 18/19 mm thick, interior grade, commercial type, fixed with screws to timber frame work complete all as specified and directed.

Prelaminated Particle Board of 18/19mm thick one side decorative face of exterior grade as in cup board shutters, shelves and partition complete all as specified and directed.

Plain fillets, square, rectangular or triangular in section clean sawn, secured with nails 2nd class hard wood exceeding 13 Sqcm and not exceeding 25 Sqcm complete all as specified and directed.

Continuous (Piano) hinges, 30 mm width of flap mild steel, bright finish or electrogalvanised complete all as specified and directed.

40mm dia, Brass Cupboard Knobs fixed with nut, screws and washers complete all as specified and directed.

Aluminium Hasp and Staple, 125mm safety type with mild steel hinge pin including bolt type complete all as specified and directed.

Ball catches with 8 mm dia steel ball, and brass body and striking plate including letting in, complete all as specified and directed.

Stainless Steel, 25 mm dia fancy type Curtain Rods fixed to brackets including brackets and fancy type corner ends complete all as specified and directed.

Dismantling plain brick tiles or Mangalore type or any other type 20 to 30mm thick from roof top including cement mortar bedding and roof treatment but not backing complete all as specified and as directed.

PCC 1:2:4 type B-1 50 mm thick (using 20mm graded crushed stone aggregate) in roof leveling concrete laid to slope for further treatment using water proofing compound as per manufacture's instructions including fair finishing to top surface complete all as specified and as directed. Note : Water Proofing Compound will be measured and paid separately.

Preparation of concrete surfaces by scrubbing down with steel brushes and cleaning with water all loose dirt/dust and applying the following Roof Treatment complete all as directed :- (a) Applying 1st course of 10mm thick screed bed with cement mortar 1:3 over concrete surface. (b) Applying 2nd course of bituminous primer conforming to IS-3384 @ 0.4 Kg/Sqm over the screed bed. (c) Applying 3rd coarse of a coat of blown type bitumen of grade 85/25 heating to a working temperature of 180° C and applied @ 1.2 Kg/Sqm.

(d) Applying 4th course of APP (Atactic Polypropylene) modified prefabricated five layer polymeric membrane 3mm thick weight not less than 3.6 Kg/Sqm with 160 Grams/Sqm non woven polyester made at centre core reinforced laid with 75 mm side overlap and 100 mm end overlap. (e) Applying 5th course of a coat of bonding material with blown type bitumen of grade 85/25 heating to a working temperature of 180° C and applied @ 1.2 Kg/Sqm and blended with fine sand in dry condition @ 0.50Kg/Sqm dusted over the bitumen coat. (f) Applying a 6th course of Solar Reflective Bituminous Aluminium Paint @ 100 grams/Sqm all as specified and as directed.

The membrane shall be laid using butane torch. The membrane shall be first laid upto the parapet wall junction and then shall be overlapped with another membrane (flashing) with an overlap covering upto a distance of 300mm. In case the parapet height is less than 500mm, the membrane shall be terminated at the top of parapet. All rain water pipe openings shall be suitably sealed with APP membrane including disconnection and refixing in same position the existing Water Storage Tanks and all GI Pipes and fittings complete all as specified and directed. Notes : 1. Contractor shall be write "Name of Contractor and Date of Laying of Membrane" with paint on the wall after laying of membrane in all respect. 2. The rate includes for filling of cracks in existing roof with cement putty using suitable bonding agent (Shalocrate-42) before laying cement plaster all as directed.

Rendering 12mm thick in cement mortar 1:3 on sunken concrete surfaces mixed with integral water proofing compound finished even & smooth without using extra cement complete all as specified and directed. Note : WPC shall be measured and paid separately under respective item.

Polymer modified Bituminous elastomeric Water Proofing Coating @ 0.60 Kg per Sqm in two layers for sunken portion of toilet complete all as specified and directed.

Cement concrete type C-2 1:3:6 (using 40mm graded crushed stone aggregate) as in mass concreting in Sunken Floor, complete all as specified and directed.

Stainless Steel Wall mounting type Cloth Drying Stand, double layer type, with drying length 30", weight not less than 3.1 Kgs, complete all as specified and directed.

Stainless Steel Kitchen Sink, made out of 1.00mm thick sheet with plug, washers, waste pipe, coupling, cast iron cantilever brackets, connecting union overall size 495mm x 420 mm with bowl size 410mm x 330mm x 160mm, fixed in repairs, complete all as specified and directed.

Stainless Steel Plate Rack 900mm x 600 mm x 200mm deep with plate racks, spoon holders, shelves etc. complete, complete all as specified and directed.

Stainless Steel Plate Rack 900mm x 600 mm x 200mm deep with plate racks, spoon holders, shelves etc. complete, fixed in repairs, complete all as specified and directed.

Rotational moulded polyethylene Water Storage Tanks of capacity 500 litres, (cylindrical vertical with threaded top), three layered, hoisted and fixed in position including supply and fixing necessary GI fittings, inlet/outlet washout, overflow pieces long nipples, check nuts & washer, brass valve 20mm high pressure with polythene float and fly nut etc. complete, fixed in repairs, all as specified and directed.

Gun metal globe or gate valve with iron wheel heads, screwed both ends for 25mm dia bore iron pipe complete all as specified and directed.

Gun metal globe or gate valve with iron wheel heads, screwed both ends for 20mm dia bore iron pipe complete all as specified and directed.

Cutting chases, pinning in, making good to facing through brick wall where required and pointing in CM 1:3 to ends of edges of landing etc and cutting chases for concealed water tubing and making good cutting exceeding 10 cm but n.exc 20 cm girth, complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specified and as directed.

Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore dia 15mm, complete all as specified and as directed.

Refixing old steel tubing and connections in new or old position with all fittings retrieved from taking down here-in-before and fixed (walls, ceiling, floors, etc.) of 15mm dia complete all as specified and as directed.

Taking up or down 20mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specified and as directed.

Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore dia 20mm, complete all as specified and as directed.

Refixing old steel tubing and connections in new or old position with all fittings retrieved from taking down here-in-before and fixed (walls, ceiling, floors, etc.) of 20mm dia complete all as specified and as directed.

Taking up or down 25mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specified and as directed.

Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore dia 25mm, complete all as specified and as directed.

Refixing old steel tubing and connections in new or old position with all fittings retrieved from taking down here-in-before and fixed (walls, ceiling, floors, etc.) of 25mm dia complete all as specified and as directed.

Pillar taps, cast copper alloy, fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe of 15mm bore, complete all as specified and as directed. Make : Jainko Cat Part No PCJ-1 / Prayag Cat Part No PS-02 / Cera Cat Part No F2002101

Bib tap with wall flange cast copper alloy chromium plated, fancy type, with capstan Head handle, screwed down, screwed for 15mm bore iron pipe or for brass ferrule, fixed in repairs, complete all as specified and directed. Make : Jainko Cat Part No BTJ-4 / Prayag Cat Part No 8606 / Cera Cat Part No F2008151

Stop cock / Angle valve with adjustable wall flange CP cast copper alloy, fancy type, with capstan head handle and adjustable wall flange, screwed down, high pressure screwed both ends for 15mm bore iron pipe or for unions, fixed in repairs, complete all as specified and directed. Make : Jainko Cat Part No AVJ-1 / Prayag Cat Part No 8910 / Cera Cat Part No F2002201

Stop valve, long cast copper alloy fancy type chromium plated with long shank and cup (concealed type) screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15mm bore, fixed in repairs, complete all as specified and directed. Make : Jainko Cat Part No CSV-5 / Prayag Cat Part No 8718 / Cera Cat Part No F4060101

Brass Chromium Plated Mixer for mixing Hot & Cold water for Sink screwed down for 15mm bore iron pipe or for unions and fixed, complete all as specified and directed. Make : Jainko Cat Part No SMJ-1 / Prayag Cat Part No 8760 / Cera Cat Part No 3001581

Brass chromium plated shower rose, fancy type, 100 - 150mm with swivel joints and fixed to steel pipe or union, fixed in repairs, complete all as specified and directed. Make : Jainko Cat Part No FSJ-1 / Prayag Cat Part No BS-27 / Cera Cat Part No F7020306CH

Vitreous china Orissa pan of pattern, long pan size 580mm x 440mm, with ‘P’ or ‘S’ trap, front or back inlet and integral foot rest complete including lime concrete bedding and connection to drain or outgoing pipe and to flushing pipe, and anti siphon pipe, fixed in repairs, complete all as specified and directed.

10 litres capacity PVC low level flushing cistern of approved make complete with PVC flush pipe and connection to water closet, fixed in repair, complete all as specified and directed.

Vitreous china wash hand basin 550 x 400mm, white flat back including cast iron bracket, cutting for and pinning the ends of brackets or erecting on stand including 32mm bore brass chromium plated waste coupling with long screwed shank and fly nuts, PVC flexible waste pipe of bore 32mm and adequate length, 15mm bore PVC connection pipe 450mm long with brass nuts on both side, fixed in repairs, complete all as specified and as directed.

PVC connection 45cm long fitted with two Nos of brass check nuts and washers complete, fixed to 15mm bore iron pipes, complete all as specified and directed.

Towel Rail 600mm long of fancy type fixed with and including chromium plated brass screws and plastic cleats complete all as specified and directed.

Soap dish, fancy type, brass chromium plated fixed to walls with brass chromium plated screws complete all as specified and directed.

PTMT shelf with and including chromium plated brass screws and plastic cleats (Minimum weight 300 grams) complete all as specified and directed.

Grating Doom 125mm dia with waste hole of PTMT (Min wt 40 grams), complete, fixed in repairs, all as specified and as directed.

Waste coupling of PTMT (half or full threaded) 32 mm dia, complete, fixed in repairs, all as specified and as directed.

PVC Waste Pipe 32mm dia flexible with cup to fit wash hand basin waste coupling complete all as specified and directed.

Low density polyethylene pipe of pressure rating 6.0 Kg/sqcm for Wash Hand Basin of 40 mm bore complete all as specified and directed.

Taking up / down AC / PVC (SWR) pipes (including all fittings), bends, floor traps with spigot and socket ends and lead joints including burning out joints and removing lead of 110 / 100mm dia pipe complete all as specified and directed.

Taking up / down AC / PVC (SWR) pipes (including all fittings), bends, floor traps with spigot and socket ends and lead joints including burning out joints and removing lead of 75mm dia pipe complete all as specified and directed.

PVC (SWR) pipes single socketed, 110mm bore in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

PVC (SWR) pipes single socketed, 110mm bore in any length with rubber ring joints, laid in walls complete all as specified and directed.

PVC (SWR) pipes single socketed, 75mm bore in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

PVC (SWR) pipes single socketed, 75mm bore in any length with rubber ring joints, laid in walls complete all as specified and directed.

PVC (SWR) bend 110mm bore complete all as specified and directed.

PVC (SWR) bend 75mm bore complete all as specified and directed.

PVC (SWR) reducers bore of pipe 110mm complete all as specified and directed.

PVC (SWR) couplers bore of pipe 110mm complete all as specified and directed.

PVC (SWR) couplers bore of pipe 75mm complete all as specified and directed.

PVC (SWR) junction single (Single T) equal or unequal with access door bore of pipe 110mm complete all as specified and directed.

PVC (SWR) junction single (Single T) equal or unequal with access door bore of pipe 75mm complete all as specified and directed.

PVC (SWR) branch piece, single (single Y) equal or unequal 75mm dia complete all as specified and directed.

PVC (SWR) Vent cowl bore of pipe 110mm complete all as specified and directed.

PVC (SWR) Vent cowl bore of pipe 75mm complete all as specified and directed.

Salt-glazed stoneware gully traps 150 x 100mm size, square or round mouthed, 'S' or 'P' type complete all as specified and as directed.

Stack clamp made of 50 x 5mm flat iron and 16mm dia round iron stays including bolt and nuts and securing ends of stay to water pipes suitable for 100 / 110mm dia pipe including taking down unserviceable clamp all as specified and directed.

Mild Steel work in Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

Preparation new plastered or previously untreated surfaces of walls and applying three coats of white wash, complete all as specified and directed.

Preparation new plastered or previously untreated surfaces of ceiling and applying three coats of white wash, complete all as specified and directed.

Preparation old plastered surfaces of ceiling including scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc. and applying two coats of white wash, complete all as specified and directed.

Preparation new plastered surfaces of walls and applying two coats of cement base paint including one coat of cement primer complete all as specified and directed.

Complete removal of existing treatment and applying two coats of cement base paint on external surface of walls, including one coat of cement primer complete all as specified and directed.

Preparation new plastered surfaces of wall and applying two coats of oil emulsion distemper over a coat of alkali resistant primer coat over and including a coat of wall care putty (Birla/JK) of average thickness 2 to 3mm complete all as specified and as directed.

Complete removal of existing treatment and applying two coats of oil emulsion distemper over a coat of alkali resistant primer coat over and including a coat of wall care putty (Birla/JK) of average thickness 2 to 3mm complete all as specified and as directed.

Preparation of new wooden surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed.

Preparation of new or previously untreated steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint, over a coat of red oxide primer, complete all as specified and as directed.

Preparation of old steel surfaces of any description, over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed.

E/M Portion

Taking out carefully copper / aluminium point wiring, (Light, fan, socket or power) complete with all fitting, fixtures such as switch socket out let, ceiling rose, holder, regulator, DB's etc. including making good the disturbed surface of wall/floors, complete all as specified and as directed.

Point wiring with multi stranded copper conductor of size 1.5Sqmm PVC insulated unsheathed FRLS cable in and including existing concealed conduit 20mm dia or more as per the site requirement including 1.50 Sqmm copper earth wire (green colour) FRLS Cable as earth continuity conductor connected to main earthing and common earth terminal for one light point or fan point or bell point controlled by one No, one way switch using cable of different insulation colour for colour coding including 3mm thick laminated sheet cover, mild steel sunken box for mounting switches etc. including cutting chases and making good to disturbed surfaces of wall / floor, complete all as specified and as directed.

All as per the description of Serial Item No 136 here-in-before but for One light point controlled by two 2-way switches, complete all as specified and as directed.

All as per the description of Serial Item No 136 here-in-before but for one 3 pin socket outlet 05/06 Amp independent, complete all as specified and as directed.

All as per the description of Serial Item No 136 here-in-before but for one 5 pin socket outlet 05/06 Amp on same board, complete all as specified and as directed.

All as per the description of Serial Item No 136 here-in-before but for one 3 pin socket outlet 15/16 Amp independent board using cable of size 2.5 Sqmm including 2.5 Sqmm copper earth wire (green colour) all as specified and directed.

Switch piano, flush type, 05/06 Amps, single pole, one way, complete all as specified and as directed.

Switch piano, flush type, 05/06 Amps, single pole, two way, complete all as specified and as directed.

Socket out let universal type, 2 in 1, 2 and 3 pin 05/06 Amp, piano flush type, 240 volts, complete all as specified and as directed.

Switch piano, flush type, 15/16 Amps, single pole, one way, complete all as specified and as directed.

Socket outlet universal type, 2 in 1, 3 pin 5 and 15/16 Amp, piano flush type, 240 volts, complete all as specified and as directed.

Ceiling rose surface bakelite three terminals 240 volts complete all as specified and as directed.

Bell push 5 Amps 230 Volts single pole complete all as specified and directed.

Bell, ding dong type AC 230 Volts single pole complete all as specified and directed

Taking down carefully existing Ceiling Fan / Exhaust Fan any description servicing and spray painting of all the exposed surfaces of fan after cleaning all dust and scratching of old paint and painting with one coat of synthetic enameled paint and writing numbering in capital letters and refixing the same including making the electrical connections with PVC insulated, overall sheathed, flexible copper conductor cable complete all as specified and as directed.

Taking down carefully existing Storage type Water Heaters (Geysers) any description and refixing the same including making the water supply connections complete all as specified and as directed.

Electronic fan regulator stepped type with five steps 240 volts 100 watt suitable for 1200mm / 1400mm sweep AC ceiling fan, complete all as specified and as directed.

Lamp holder PVC case body of Bakelite with back plate suitable for batten fittings complete all as specified and as directed.

LED Lamp 230 Volts 12 watts, in white colour with maximum Lumen output (850 lm) and colour temp 3000 K with base cap B-22, complete all as specified and as directed.

Tube light fitting, batten type suitable for and including LED 20 tube Rod 4' long with decorative colour in aluminum housing and integrated electronic driver and all accessories pre-wired and making connections with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connector to light fitting complete all as specified and as directed.

Tube light fitting, batten type suitable for and including LED 10 tube Rod 2' long with decorative colour in aluminum housing and integrated electronic driver and all accessories pre-wired and making connections with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connector to light fitting complete all as specified and as directed.

Bulk head luminaries energy saving, surface mounted, decorative bulk head back-lit LED luminaries complete with all accessories suitable for and including 1 x 10 Watts LED lamp including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230 Volts 50 Hz complete all as specified and as directed.

Distribution Board iron clad TPN DB, double door with IP-43, IK-09 protection, Four Way, vertical, suitable MCCB FP 415 Volts 125 Amps rating as incommer and MCB as outgoing complete with appropriate size copper busbar including cutting chases in walls for fixing the DB and making good disturbed surfaces of walls, complete all as specified and as directed. Note : MCBs / MCCBs shall be measured and paid separately under the respective item.

MCCB TPN 415 Volts 125 Amps rating, 25 KA rupturing capacity with adjustable Thermal Magnetic trip release, complete all as specified and as directed.

Sheet metal enclosure factory made double door for DB 240 volts with 200 Amps rated bus bar SPN 8 Way including taking down and making good disturbed surfaces of walls, complete all as specified and as directed.

MCB SP 6 to 32 Amp 10 KA, 'C' curve, complete all as specified and as directed.

MCB SPN 6 to 32 Amp 10 KA, 'C' curve, complete all as specified and as directed.

Sub main wiring with two single core PVC insulated multistrandred un-sheathed FRLS cable of size 6.0 Sqmm with stranded copper conductor, drawing into concealed PVC conduit / surface batten (including conduit and accessories) with continuous PVC insulated multistrandred unsheathed FRLS cable earth wire of 6.0 Sqmm dia including taking out unserviceable sub main wiring, complete all as specified and directed. Note : Three runs of 6.0 Sqmm wire and one run of PVC conduit shall be considered as one unit length.

Sub main wiring with two single core PVC insulated multistrandred un-sheathed FRLS cable of size 4.0 Sqmm with stranded copper conductor, drawing into concealed PVC conduit / surface batten (including conduit and accessories) with continuous PVC insulated multistrandred unsheathed FRLS cable earth wire of 4.0 Sqmm dia including taking out unserviceable sub main wiring, complete all as specified and directed. Note : Three runs of 4.0 Sqmm wire and one run of PVC conduit shall be considered as one unit length.

Rigid Non-metallic PVC conduit 20mm dia including all tees, bends, elbows, reducers, bell mouth tube end and fixing assembly such as couplers, lock nuts, saddles and pipe hooks etc. complete all as specified and as directed. Note : Cutting chases for concealing the PVC conduit, wherever required shall be done by the Contractor as directed at site. The cost of cutting chases, pinning in, making good to facing through brick wall where required and pointing in CM 1:3 to ends of edges shall be deemed to be included in Quoted Rate of this item.

Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground vertically to a depth not less than 2.25 metre deep below GL with top edge of the plate not less than 1.5 mtr below normal GL and connected to earth plate surrounded by 15 cm thick packed layers of charcoal dust and common salt and connected to earth lead galvanised iron strip 25 x 4mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel and thimbles and other end of the earth wire connected to DB and protected by galvanised iron or steel pipe light grade 15 mm bore and water pipe 20mm bore GI light grade with funnel and wire mesh, including all necessary excavation and earth work PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover and all as shown in electrical plate No 3 of MES schedule Pt I of 2009, RCC pit cover shall be pre-cast of RCC (1:2:4) type B-I , 80mm thick reinforced with XPM weighting not less than 4.0 Kg/Sqmm complete all as specified and as directed.

M/S ARUN ANAND

M/s Mohan lal

ANIKET TRADERS

M/S MOHAN LAL GUPTA

M/S Shesh Paul Gupta

DES RAJ NAGPAL CONTRACTORS PVT.LTD

bamral builder

Bidder Name

INDERJIT SINGH

M/S Shesh Paul Gupta

M/S ARUN ANAND

ANIKET TRADERS

M/s Mohan lal

M/S MOHAN LAL GUPTA

DES RAJ NAGPAL CONTRACTORS PVT.LTD

bamral builder