SPECIAL REPAIR TO BUILDING NO. P-912/1, 912/2, 912/3 AT 51 SQN, PROVISION OF WASHROOM CUM CHANGING ROOM AT 51 SQN AND PROVISION OF WEATHER SHELTER FOR OUTDOOR UNITS OF AIR CONDITIONER AT 45 WEU AT AF STATION SRINAGAR

Amount

Demolition of brick work or stone masonry walls, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles, all as specified.

M&L for brick work with sub class 'B' Bricks (using old size bricks) straight or curved on plan exc 6 m mean radius, built in CM 1:4, complete all as specified and as directed.

Taking down cement plaster of any description on brick or stone masonary wall , etc including racking out joints, hacking for key, scrubbing down with water etc, all as specified.

M&L for 15mm thick rendering in cement mortar 1:6, on brick masonary or concrete surfaces of walls, finished even and smooth without using extra cement, all as specified.

M&L for 15mm thick rendering in cement mortar 1:4, on brick masonary or concrete surfaces of walls, finished even and smooth without using extra cement, all as specified.

M&L for applying 2 mm thick cement base wall care putty on plastered surface of wall, and making the surafce even & smooth for reciving distemper / paint of any descreption all as specified & directed.

M&L for preparation of walls surfaces and applying two coats of oil bound distemper over a coat of primer, all as specified.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of primer in camouflaging pattern as approved, all as specified and directed.

M&L for complete removal of existing treatment from the plastered wall surfaces and applying two coats of oil bound distemper, over one coat primer and 2 mm thick cement base wall care putty, complete all as specified and directed.

M&L for complete removal of existing treatment from the plastered, concrete wall surfaces and applying two coats of cement base paint, over one coat of primer in camouflaging pattern as approved, complete all as specified and directed.

Taking down chowkats or frames including shutter (without taking off shutters from the frame) area n exc 1.50 Sqm each, complete all as specified.

Taking down chowkats or frames including shutter (without taking off shutters from the frame) area exc 1.50 Sqm but n.exc 4.00 sqm each, complete all as specified.

S&F aluminium frame for ventilators with powder coating (minimum thickness of powder coating 50 micron) of any colour, with one or more rebates including joining cleat for fixing etc, complete all as specified.

S&F aluminium ventilator shutters with powder coating (minimum thickness of powder coating 50 micron) of any colour, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.), hinges type B-21, 100mm long (2 no.), suitable handle (1 no.), complete all as specified

S&F 5 mm thick sheet glass, ordinary quality and glazing with glazing clips to aluminium framework in squares exceeding 0.5 Sqm in each pane, all as specified.

Supply fabricate & fix in position anodised aluminium powder coated (minimum thickness of powder coating 50 micron of approved colour) door shutter with frame, partly glazed with 5 mm thick tinted glass and partly panelled with 5 mm thick aluminium camposit pannel of approved coloure & pattern including rubber bead joining cleat for fixing in position, aluminium door handle 150 mm size (2 Nos), aluminium barrel tower bolt 200 mm size(3Nos) and Tower bolt of 150 mm size (2 Nos), aluminium hinges 100 mm size etc all as specified below complete all as specified and directed. (a) Frame (top & side) section shall of size 101.60 x 44.75 x 2.4 mm ( Section No 14021)

(b) Vertical Members of shutter Section shall be be of size 85.00 x 44.45 x 2.00 mm (Section No 19560) (c) Top Members of shutter Section shall be be of size 83.50 x 44.45 x 2.00 mm (Section No 19581) (d) Lock rail (Middle member) of shutter Section shall be be of size 150.00 x 44.45 x 3.00 mm (Section No 19596) (e) Bottom Members of shutter Section shall be be of size 150.00 x 44.45 x 3.10 mm (Section No 19584) (f) Glazing clip for securing glass of shutters shall be be of 0.80 mm thick (Section No 19370). Note:- (i) Section No given above are of make Jindal, Contractor may use similar section of other make mention in Appx A

Supply fabricate & fix in position aluminium powder coated (minimum thickness of powder coating 50 micron of approved colour) three track window ( two shutters glazed & one shutters wire gauge) with frame, glazed with 4 mm thick tinted glass and, wire gauge with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm including rubber bead joining cleat for fixing in position, concealed type lock for all three shutter, PVC roller etc all as specified below, complete all as specified and directed. (a) Frame (top & side) section shall of size 92.00 x 31.75 x 1.50 mm ( Section No 20831)

(b) Frame (bottom) section shall of size 92.00 x 31.75 x 1.50 mm ( Section No 20832) (c) Top & side Members of shutter Section shall be be of size 18.00 x 40.00 x 1.55 (Section No 20738) (d) Shutter Interlock Section shall be be of size 18.00 x 40.00 x 1.45 (Section No 20737) (e) Bottom Members of shutter Section shall be be of size 18.00 x 40.00 x 1.55 (Section No 20736) Note:- Section No given above are of make Jindal, Contractor may use similar section of other make mention in Appx A

M&L for aluminium grill powder coated (minimum thickness of powder coating 50 micron) 5.5 mm thick and size of aperture 105 mm x 99 mm fixing with and including alunimium U channel as per manufacturer instruction, all as specified. Make:- Deco Grill (DG-104) or equvallent make approved by GE

M&L for framed work such as grills, gratings, etc.. with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290, Gde-E-165, all as specified.

S&F door closer hydraulicaly regulated, designation No. 2 universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 KG complete all as specified.

S&F factory made solid PVC moulded door shutter 28 to 30 mm thick (styles) with 2,4, or 6 raised panel design with 2 mm thick moulded PVC sheet of 02 mm on front face and 2 mm plain colour PVC sheet on back face all as specified and directed with particle board core, all as specified.

S&F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain single side prelam PVC sheet used instead of plain colour PVC sheet with MS square tube S&F in opening as per specification and drgs and edges will be painted to match with prelam sheet complete all as specified.

S&F 100 mm long extruded aluminium handles, cast type, anodised, complete all as specified.

S&F 100 mm long aluminium anodised, barrel tower bolts of extruded section and fixed, all as specified.

S&F 100 mm long butt hinges, medium weight, cold rolled mild steel and fixed, complete all as specified.

S&F in repair 25 mm dia stainless steel tubular drapery rod, cut to size, fixed in position with and including stainless steel holder and end finial / cap, including standard ring complete all as specified.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets, fillets & snap grid etc, complete all as specified.

S&F aluminium powder coated (minimum thickness of powder coating 50 micron) snap grid frame work of T section (main & cross member) of size 25 mm x 25 mm x 1.5 mm thick in square pattern of grid size 600 mm X 600 mm . The aluminium fram work will supported on side wall with the used of aluminium 'L' section of size 25 mm x 25 mm x 1.5 angles etc. Snap grid shall be supported with hangers of 4 mm dia. Galvanised iron wire adjusting level fixed to roof slabs / truss etc by means of ceiling cleats made out of Galvanised iron flat of size 40 x 3 mm size 60 mm long and expansion hold fasteners 12.5 mm dia 40 mm long complete all as specified directed by the Engineer-in-Charge.

M&L Gypsum Board tiles of size 600 mm x 600 mm x 12 mm thick in ceiling fixed to existing snap grid as per manufacturer instruction including necessary jointing and taping including preparation of surface and applying two coats of Oil bound distemper over a coat of primer, complete all as specified and directed by Engineer-in-Charge.

S&F wooden panelling of second class softwood 12 mm thick with tongue and groove joint fixed in any position over and including wooden framework in second class softwood with plain fillets square or rectanglular in section clean sawn, secuired with nails / screws of sectional area exc 13 Sqcm and n exc 25 Sqcm at n exc 90cm centre to centre in both direction and including threee coats of french polishing on all the exposed surfaces, complete all as specifed.

Demolition of floor, hearth or wall tiling or stone slab laid, bedded & pointed in any mortar including demolition of cement mortar bedding or backing coat, including rubbish off the premises, all as specified.

M&L for 25 mm thick cement concrete type B-0, 1:2:4 (using 12.5 mm graded stone aggregate), as in sub base, all as specified.

M&L 15 mm thick screed or bedding layer in cement mortar (1:6) for laying floor finishes, complete all as specified.

M&L 10 mm thick rendring / backing coat in cement mortar (1:4) to receive wall tiles, complete all as specified.

M&L light shade colour vitrified ceramic tiles 10mm thick (square/rectangular ) polished, area of each tiles n.exc 0.36 sqm in floors etc laid over existing screed bed, set and jointed in neat cement slurry and pointed in white or coloured cement to match.

M&L light shade colour vitrified ceramic tiles 10mm thick (square/rectangular ) polished, area of each tiles n.exc 0.36 sqm for skirting / dado etc laid over existing backing coat, set and jointed in neat cement slurry and pointed in white or coloured cement to match.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.16 sqm in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match, all as specified.

M&L for coloured glazed ceramic tiles in vertical surfaces of size 450 x 300 x 6-7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, complete all as specified.

M&L for granite (of any type) tiles 20 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing, complete all as specified.

Demolition of reinforced cement concrete of any description (reinforcement cut as required to facilitate demolition) and in any position, complete all as specified.

M&L for reinforced cement concrete of Nominal mix 1:2:4, type B1, using 20 mm graded stone aggregate, as in selves supported on walls, beams etc., all as specified.

Use & waste form work to sofit / edge of suspended selves and similar workn not exc 200 mm thick flat fair finished surfaces, all as specified.

M&L for mild steel TMT bars 10 mm dia and over, cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binging with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing, all as specified and directed.

S&F 15 mm bore galvanized steel tubes, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors, all as specified and directed.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing, all as specified and directed.

S&F 20 mm bore galvanized steel tubes, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors, all as specified and directed.

M&L for lagging to 20mm dia pipes, all arround with 25mm thick bonded mineral wool pre-formed `SNAP ON` pipe sections of density 144 Kg/cum conforming to IS 9842, all as specified and directed.

M&L for lagging to 15mm dia pipes, all arround with 25mm thick bonded mineral wool pre-formed `SNAP ON` pipe sections of density 144 Kg/cum conforming to IS 9842, all as specified and directed.

S&F in repairs sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm, all as specified.

S&F in repairs waste coupling of PTMT (half or full threaded), minimum weight 45 gms, suitable for discharge pipe of 40 mm bore dia complete all as specified.

S&F in repairs waste pipe 40 mm fixed to sink, all as specified and as directed.

S&F in repairs 15 mm size cast copper alloy chromium plated sink mixture, wall mounted, with capstan heads, screwed down, high pressure, complete all as specified and directed.

S&F 15 mm size cast copper alloy chromium plated wall mixture, with capstan heads, screwed down, high pressure, complete all as specified and directed.

Taking down rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan necks etc, all as specified.

S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or floors, all as specified.

S&F 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or floors, all as specified.

S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls, with PVC clamp all as specified.

S&F 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls, with PVC clamp all as specified.

S&F 75 mm dia PVC (SWR) bends any radius, all as specified.

S&F 75 mm dia PVC (SWR) bends any radius with access door, all as specified.

S&F 110 mm dia PVC (SWR) bends any radius, all as specified.

S&F 110 mm dia PVC (SWR) bends any radius with access door, all as specified.

S&F 75 mm dia PVC (SWR) vent cowl,complete all as specified.

M&L for PVC floor trap of 75 mm dia of outlet, plain with CP grating of 100mm dia including jointing with solvent cement, including embedding with PCC 1:2:4 type B-1, all as specified and directed

Supply and fix in repair white vitreous China wash hand basin (Flat back) of size 550 x 400 mm fixed on and including new brackets complete including, 32 mm size brass chromium plated waste coupling, chain and plug and porcelain stopper, etc complete.

S&F in repair 15 mm size basin mixture cast copper alloy chromium plated with capstan heads, half turn type, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified.

S&F in repairs white Vitreous china wash down water closet (pedestal pattern) with fixing bolt, brass chromium plated Jet shower with one meter long flexible pipe including all connection complete.

S&F in repiars plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, complete all as specified, complete all as specified.

S&F in repairs for 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and connection to pipes and incl 32mm dia pipe for low level cistern flush pipe, complete all as specified.

S&F in repairs vitreous china urinal half stall type white (excluding flushing cistern, flush pipe and waste pipe) including providing and fixing plugs, bedding urinal against wall in CM 1:2, securing urinal to plugs with and incl 60 mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, complete all as specified.

S&F in repairs urinal spreader of PTMT any colour for fixing with 15 mm dia pipe (minimum weight 60gms), complete all as specified.

S&F in repairs for 15 mm size bib taps fancy type, cast copper alloy chromium plated, with capston head, screwed down, screwed for iron pipe or for brass ferrule and fixed, all as specified.

S&F in repairs for 15 mm size angle cock, chromium plated fancy type, cast copper alloy, screwed dowon, high pressure, with capston head, screwed both ends for iron pipe or for unions and fixed, all as specified.

S&F PVC connections 15 mm size with PTMT nuts of length 600mm, complete all as specified.

S&F in repairs toilet paper holder of brass, chromium plated fixed to walls with chromium plated (CP) brass screws,complete all as specified.

S&F in repairs brass Chromium plated, tubular towel rail, 20 mm dia, D type, 60 cm long between flanges, complete all as specified.

Demolition of cement concrete (unreinforced) in ground floor and in paving n exc 15 cm thickness (below or above ground level), complete all as specified.

M&L for 75 mm thick PCC 1:3:6, type C-2 (using 40 mm graded stone aggregates), as in plinth protection, finished the surface even and smooth without using extra cement, complete all as specified & directed.

M&L for 75 mm thick PCC 1:4:8 type D2 using 40 mm graded aggregate as in sub base all as specified and as directed by Engineer-in-Charge.

M & L for dry reiver sand screed bed for PCC paver block, including gently compacting complete all a specified and directed. NOTE :- compacted thickness of sand will be measured and paid. )

Material & Labour for machine pressed precast concrete interlocking paver block confirming to IS 15658, of approved shape and size of 80 mm thickness, with minimum compressive strength of 40 N / Sqmm (M-40 grade), without correction factor for chamfering, made in rubber moulds with 0.50 mm thick scratch proof lacquer coating on top surface, with white cement and pigment laid over existing screed bed complete

M&L for Filleting in any position and any shape in PCC 1:2:4 type Bo, including all mitres, stops, etc. Sec of fillet exc. 25 sqcm but n.exc 50 sqcm.

Demolition and breaking up 150 mm dia bore sewage / drain pipe / RCC hume pipe including PCC packing under haunching against the sides of pipe bed and complete PCC of bed all specified and directed.

M&L for PCC 1:4:8 type D 2 using 40mm graded stone aggregate as in foundation, filling, mass concrete complete.

Surface excavation n. exc. 30 cm deep and averaging 15 cm deep and getting out in soft / loose soil.

Excavation in trenches, not exc 1.5 m wide and not exc 1.5 m in depth, for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. not exc 10 sqm on plan and not exc 1.5 m in depth and getting out in soft / loose soil, complete all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm using excavated soil complete all as specified.

Filling in floor / plinth including spreading, levelling, watering and well ramming in layers not exceeding 25 cm using excavated soil complete all as specified.

Removing excavated soil to a distance exc 250 m but n.exc 500 m and depositing at a level not exceeding 1.50m above the starting point all as directed at site.

M&L for Providing cement concrete type B-1, 1:2:4, using 20 mm graded stone aggregate, as in copings, lintle up to 1.5 m span, apex stones, bed plates, kerbs / benching to manhole etc including weathering, slightly rounded or chamfered angles and throating as directed

S&F for 150 mm internal dia reinforced concrete pipes, class NP 2 with one collar per length of pipes, laid in trenches and jointed in cement mortar all as specified including testing complete.

M&L for cement concrete 1:3:6 type C-2, as in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150mm bore of pipes, complete all as specified.

M&L extra for forming fair finished drain or channel 15 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc., all as specified and directed.

M&L for pre-cast reinforced cement concrete (1:2:4), type B-1 (using 20mm graded stone aggregates), as in cover slab for man holes, set in CM (1:4) etc includimg necessary form work, complete all as specified.

M&L for HDPE septic tanks designed for sewage and sludge water, of suitable diameter & height for 25 users, including excavation in any type of soil, PCC 1:4:8 in foundation including lowering, inlet & outlet connections, vent pipe, cover all as per manufacturer's specifications and instructions, complete all as specified and directed by Engr-in-Charge. Make- Sintex, Comfort polymers or equvallent make approved by GE.

M&L for Construction of soakage well including excavation in any type of soil, PCC in foundation, walls in honey combed masonry with top ring concrete including intercepting chamber & screen chamber made of brick masonry in cement mortar, RCC top cover and filled with brick bats of size 2.40m dia and 3.00m depth, complete all as specified and shown on drawings No CE/AF/STD-15 / 2000.

M&L for 40mm thick damp proof course in cement concrete 1:2:4, type B-0, to horizontal or vertical surfaces including necessary formwork, complete all as specified.

M&L for preparation of newly plastered surfaces of walls and applying three coats of white wash, all as specified.

M&L for hardcore of broken stones or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface of broken stone or boulders, complete all as specifed.

M&L for 100mm thick cement concrete type D- 2, 1:4:8 (using 40mm graded aggregate) as in sub base, complete all as specified.

S&F 12 mm thick toughened frosted glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required including all necessary stainless steel fasteners & fittings like handle, door hinges etc., complete all as specified and directed by Engr-in- Charge.

S&F toilet paper holder, brass, chromium plated fixed to walls with chromium plated brass screws, complete all as specified and as direted by the Engr-in-Charge

S&F white colour, vitreous china wash hand basin, under counter type of size 560 mm x 450 mm x 185 mm including cutting hole for WHB in granite top, 32 mm brass chromium plated waste fitting, PVC waste pipe, including finishing the joint with white cement, complete all as specified and directed by Engr-in-Charge.

S&F cast copper alloy chromium plated basin mixture single lever with braided hose of 15 mm bore dia, with capstan heads, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified make - Somany Cat part No. 272111110011 of BELLIS series or equivalnet cat No of make Jaquar / Hindware.

S&F brass chromium plated shower roses with or without swivel joints of size 125 mm, including fixing to steel pipe or union, complete all as specified.

S&F brass chromium plated soap dish, fixed in position complete all as specified and directed by Engr-in-Charge. Make - Somany Cat part No. 272130160051 of EVITA series or equivalnet cat No of make Jaquar / Hindware.

Supply and fix 1000 litres capacity double layer, rotational molded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and complete.

M&L for ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed of 20 mm.

S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment, Fe-410-W (Gde-E-250) quality A, all as specified.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm but n exc 10cm long & diametre 16 to 20mm, all as specified.

M&L for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer, all as specified.

S&F for pre-painted galvaume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws all as specified.

S&F pre-painted galvaume aluminium zink coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof ridges, fixed with self tapping screws as specified, complete all as specified.

S&F 0.63 mm thick plain, galvanised, mild steel sheeting, as in eave boards, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275, all as specified.

Excavating in post holes in soft / loose soil (or similar holes) each n.exc 0.5 cum, getting out, returning, refilling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm in any type of soil including removing surplus soil to a distance n exc 50 m complete all as specified and directed.

S&F Steel work in trusses fabricated with rectangular / Square hollow section, including special shaped, washers etc including cutting welding, bending in shape etc using tube of YST 310 grade confirming to to IS-4923 complete all as specified & directed. Make:- TATA / Asian / Jindal

Taking down copper / aluminium point wiring (light,fan,socket & power) complet incl fixtures and fittings such as switches,ceiling rose,pendent holdes, regulators, sockets, light fitting etc and making good disturbed surface of wall, floor etc complete as specified and directed.

Material & Labour for point wiring for one light / Fan point controlled by one, one way switch complete with 1.5 Sqmm multi-stranded copper conductor PVC insulated, unsheathed, fire retardant low smoke cable 1100 volts grade ISI marked drawn and including PVC rigid conduit not less than 20 mm dia, including all accessories like bend, tees, junction boxes etc., 1.5 Sqmm multi-stranded copper conductor PVC insulated, unsheathed, fire retardant low smoke cable as a earth wire connected to common earth dolly, etc and including sunken type pressed steel terminal box of suitable size for modular type switch with cover plate & frame complete. Note - Colour code of cable Phase-Red Neutral- Black and Earth -Green)

All as per item No 121 above but point wiring for one 5 / 6 Amps socket outlet on independent board controlled by one-way switch.

All as per item No 121 above but point wiring for one 5 Amps socket outlet on same board controlled by one-way switch.

All as per item No 121 above but wiring with 2.5 Sqmm multi-stranded copper conductor PVC insulated, unsheathed fire retardant low smoke, cable and 1.5 Sqmm multi-stranded copper conductor PVC insulated, unsheathed fire retardant low smoke, cable as earth wire connected to common earth dolly for 15 Amps multipurpose socket outlet on independent board, controlled with one way switch.

S&F modular one way switch 6 Amp 240 volt marked light / fan suitable for one moduel etc complete as specified and directed.

S&F Modular 6 Amp 5 pin universal socket suitable for two moduel , 250 volts complete all as specified and directed.

S&F modular switch one way 16 Amps 240 volts suitable for one moduel complete as specified and directed.

S&F Modular 6 /16 Amp socket suitable for two moduel , 250 volts complete all as specified and directed.

S&F modular step type two moduel fan regulator suitable for 120 watt 250 volts complete as specified and directed.

M&L for ceiling rose with three terminal as per relevant IS complete as specified and directed

S&F in repair energy efficient LED tube light fitting with built in LED & integral LED driver 18 to 20 watt, channel housing & diffuser of length 1200 mm (approx) with all accessories, fixing arrangement internally pre-wired, fixed in position & connecting complete all as specified and directed by Engg –in-charge.

S&F in repair energy efficient LED tube light fitting with built in LED & integral LED driver 10 watt, channel housing & diffuser of length 600 mm (approx) with all accessories, fixing arrangement internally pre-wired, fixed in position & connecting complete all as specified and directed by Engg –in-charge.

S&F recess mounting 36 watt LED ultra slim ceiling light with extruded aluminium housing and milky diffuser incl suitable size driver and 3 core flexible cord from ceiling rose to connector of fitting etc complete as specified and directed. Make:- CG - Cat No LCTRH-36-TL or equivalent of make Havells / Wipro

S&F recess mounting 18 watt LED ultra slim ceiling light with extruded aluminium housing and milky diffuser incl suitable size driver and 3 core flexible cord from ceiling rose to connector of fitting etc complete as specified and directed Make CG No LSDN-18-CDL/T/LWW or equivalent of make Havells / Wipro

S&F Energy saving new generation 20 W LED IP 65 bulkhead luminair with opal diffuser etc complete as specified and directed by Engr-in-charge Make -C&S model No LTB20WLED or equivalent of make CG / Havells / Wipro

S&F LED 10 W Recess mounted pressure die cast aluminium luminair in powder coated white finish in round profile with opimized heat sink for efficient heat dissipation and separate replaceable electronic driver etc complete as specified and directed Make- Havells - Cat part No LHEBJNP7PZ1W010 or equivalent of make CG / Wipro

S&F in repair LED flood light fitting 50 watt IP 66 high power flood light with pressure die cast aluminium housing complete with all accessories incl 3 core flexible cable from ceiling rose to connector of fitting etc complete as specified and directed. Make:- C&S model No LTEFI50WHPLED or equivalent of make Havells / Wipro

S&F epoxy powder coated or polystrene insulated material sheet metal enclosure factory made (double door) 4 way TPN (VTP) suitable for MCCB DB's 415 Volts with 200 Amps rated busbar, neutral & earthing link bar, flush/surface mounting complete all as specified and directed.

S&F epoxy powder coated or polystrene insulated material sheet metal enclosure factory made (double door) 8 way SPN suitable for MCB DB's 240 Volts with 200 Amps rated busbar, neutral & earthing link bar, flush/surface mounting complete all as specified and directed

S&F MCB single pole and neutral ISI marked `C' series working on 240 volts 50HZ AC supply for incomming & out going controlling system of capaicty 63 Amps 10 KA breaking capacity etc all as specified and directed.

S&F MCB single pole ISI marked ISI Marked `C' series working on 240 Volts 50 HZ AC supply for incomming and out going controlling cercuit of capacity 6-32 Amp breaking capacity 10 KA etc all as specified and directed.

S&F MCB single pole ISI marked ISI Marked `C' series working on 240 Volts 50 HZ AC supply for incomming and out going controlling cercuit of capacity 63 Amp breaking capacity 10 KA etc all as specified and directed.

S&F MCCB's with electronic earth leakage model 125 Amps lcs=100 % lcu 4 pole 16 KA termal magnetic setting Ics 100% lcu 415 V 50 HZ

Material & Labour for sub main wiring with 2 run single core multistranded copper conductor cable, of size 4.0 Sqmm, PVC insulated, unsheathed, fire retardant low smoke, drawn through and including heavy duty rigid PVC conduit not less than 20 mm dia with all necessary fitting and including one run single core multistranded copper conductor cable, of size 4.0 Sqmm, PVC insulated, unsheathed, fire retardant low smoke as earth wire, fixed on wall / ceiling, complete. Note: (i) 2 Runs of main cable and one run earth wire with conduit will be measured as one Unit for payment.

Material & Labour for sub main wiring with 2 run single core multistranded copper conductor cable, of size 6.0 Sqmm, PVC insulated, unsheathed, fire retardant low smoke, drawn through and including heavy duty rigid PVC conduit not less than 20 mm dia with all necessary fitting and including one run single core multistranded copper conductor cable, of size 6.0 Sqmm, PVC insulated, unsheathed, fire retardant low smoke as earth wire, fixed on wall / ceiling, complete. Note: (i) 2 Runs of main cable and one run earth wire with conduit will be measured as one Unit for payment.

Material & Labour for sub main wiring with 4 run single core multistranded copper conductor cable, of size 10 Sqmm, PVC insulated, unsheathed, fire retardant low smoke, drawn through and including heavy duty rigid PVC conduit not less than 20 mm dia with all necessary fitting and including one run single core multistranded copper conductor cable, of size 10.0 Sqmm, PVC insulated, unsheathed, fire retardant low smoke as earth wire, fixed on wall / ceiling, complete. Note: (i) 4 Runs of main cable and one run earth wire with conduit will be measured as one Unit for payment.

Disconnecting and taking down serviceable exhaust fan any type, size & any capacity with all accessories from existing place with out any damage and refixing the same after oiling, greasing and painting with one coat of synthetic enamelled paint after preperation of surface as per specified and making full serviceable incl replacement of 3 core pvc insulated copper conductor cable from ceiling rose to fan and writing the MES No etc complete as specified and directed

Supply and fix in repair heavy duty exhuast fan 300mm, 900 rpm turbo force model single phase incl all accessories as per manufacturer norms and unserviceable fan deposited in MES store yard etc complete as specified and directed by EIC Make -havells/usha/ketan

Disconnecting, taking down ceiling fan from existing place and refxing the same after replacement of rubber bush, canopy, capacitor 2.5-mfd, including greasing / oiling and painting one coat of synthetic elament paint after preperation of surface as per specified incl replacement of unserviceable suitable size 3 core copper cable from ceiling rose to connector of fan etc and writing the MES No complete as specified and directed by EIC.

S&F in repairs Air termination single pointed copper rod not less than 12 mm dia and 300mm long including fixing arrangements and taking down old one etc all as specified and directed by Engr-in-charge

S&F copper strip of size 20 x 3.15 mm with saddles and fixing screws, etc., for roof conductors and down conductors above ground incl taking down old one etc complete all as specified and directed by Engr-in-charge

Material and labour for earthing complete with copper earth plate electrode 600 mm x 600 mm x 3.15 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m deep below normal ground connected with copper strip 20 x 3 mm by means of bolts nuts check nuts and washer of galvanized steel, watering pipe of 20 mm bore galvanised iron light grade and 40 mm bore galvanised iron light grade for earth strip protection including all excavation earth work in any type of soil, PCC pit in PCC 1:2:4 type B-1 and RCC 1:2:4, type B1 for precast chamber cover 50 mm thick, reinforced with welded steel wire fabric or XPM Jali (weight not less than 4.00 Kg / sqm), with charcoal, salt, funnel complete all as shown in the electrical plate No 3 of SSR part –I and testing on completion.

Note:- Quoted rates shall be deemed to include for earth strip with protection pipe up to 7.5 M length

Taking down & Refixing of GI / Copper earth strip with suitable size nut,bolt washer of same material such as GI / Aluminium / Copper etc complete as specified and directed by Engr-in-charge

M&L for cutting existing 20 mm bore GI tubing for making new connection for 15 mm pipe including provision of 20 mm size union, 20 x 15 mm reducer T complete all as specified

Supply and fix storage type water heater 5 star rated, 50 liters capacity vertical wall mounting type made out of CRCA outer body, stainless steel storage tank, titanium enameled heating element, thermostat, thermal cutout, glass wool, fixed in position as per manufacturer's instruction & writing the MES No etc complete as specified and directed by EIC . Make:- Havells / Jaguar / Crompton / Recold

M/S FAROOQ AND SONS

M/S Haji Zahoor Hussain Ganai