Construction of Semi Covered shed for Paddy Storage along with basic amenities of 7000 MT Capacity (2x3000M.T and 1x1000M.T) in survey No.283/1 and 284/1 to an extent of 3.34.74 Hectare at Korukkai Village in Thiruthuraipoondi Taluk in Thiruvarur D

CIVIL WORK

Earth work excavation for foundation in all classes of soils and sub-soils and to full depth as may be directed except in hard rock requiring blasting including initial leads and lifts and refilling the sides of foundation with excavated earth in 150 mm layers well watered, rammed and consolidated including depositing surplus earth within the godown or inside compound in places shown with initial lead of 10 mts and initial lift of 2 mts. Clearing, leveling the site, shoring, strutting, bailing of water wherever necessary etc., complete complying with standard specification and as directed

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in hard rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts within the compound in places shown by the departmental officers and clearing and leveling the site, etc., complete complying with standard specification.

Providing and laying sand gravel mix 1:3 to a consolidated thickness of 15cm using 0.25M3 of crushed stone sand and 0.87 M3 of gravel Per 1M3 of compacted volume of sand gravel mix to give a minimum soaked CBR value as per IRC 37 - 1984 including cost and conveyance of sand and gravel to work site and stacking them to departmental metric gauge for premeasurements mixing the required quantities of sand and gravel spreading watering and compacting the mix in layers of thickness not exceeding 100mm compacted thickness by 80-100KN power roller rolling to achieve the required density including labour charges for mixing spreading and hire and fuel charges for power roller water sprinkler and all other tools and plants etc., complete complying with standard specification and as directed by the Corporation officers.

Supplying and filling in foundation with Gravel in layers of not exceeding 150mm thick well watered, rammed and consolidated including watering etc., complete complying with standard specification and as directed.

Supplying and filling in basement with wetmix 450mm thick in layers of not exceeding 250mm thick, well watered, rammed and consolidated including machineries for hire and running charges leader 5 Cum capacity, hire charges for tipper, water sprinkler,` vibratory roller all labour charges etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and filling in foundation, basement, etc., filling with crushed stone sand in layers of not more than 15cm thick well watered, rammed and consolidated etc., complete complying with standard specification and as directed by the departmental officers.

CEMENT CONCRETE 1:5:10(one cement, five sand and ten aggregate)using 40mm gauge hard broken granite stone jelly for foundation including mixing by mechanical means de-watering side shuttering , strutting, wherever necessary including curing etc., complete complying with standard specifications and as directed.

Supplying and laying hydraulic pressed monolithic natural grey colour cement concrete inter locking paver block of 83mm thick in cement concrete 1:2:4 (One cement, two sand, four aggregate) using different design and with stand for pressure of 150-200 kg/m2 over the existing sand cushion by using earth rammers and also vibrating the concrete blocks often laying using plate vibrator etc., complete as directed by the departmental officers.

Providing and laying in position, Standardised Concrete Mix M20 Grade in accordance with IS:456-200 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/M3 and maximum water cement ratio of 0.55, including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improvement workability without impairing strength and durability with about (5 Cu.m) 7730 Kg of 20mm machine crushed stone jelly and with about (3.3 Cum)5156 kg of 0-12mm machine crushed stone jelly and with about (4.7 Cum) 7670 kg of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, cutting etc., and Providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra etc., complete complying with standard specification and as directed the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of 15 Standards. (No separate payment will be made by the Department for the excess usage of materials. In foundation and basement

In Ground floor upto 4.50M height above basement.

Providing FORM WORK for centering the soffits of all reinforcement concrete work including strutting to the required (3 metre) height with mild steel sheets of size 90cm x60cm 10gauge stiffened with welded mild steel angles of size 25mm x 25mm x 3mm laid with country wood joist of average of size 10cm x 6.50cm at about 90cm centers with casuarinas props of 13cm dia at 75cm centre to centre with all nails coir, wedges complete and removing the form work after necessary curing period as directed by the corporation officers. The rates should inclusive of cutting, bending, welding charges of M.S.sheets; M.S. angles etc complete complying with standard specification and as directed. Column footing, Plinth beam and top tie beam.

Vertical slab, side slabs, Boxing, vertical drops, facia, vertical all etc.,

For place surfaces such as rectangular, square RCC columns etc.,

Supplying, fabricating and placing in position MS/RTS grills for reinforcement for all R.C.C.works including cost of steel, labour for straightening, bending, cranking, tying grills with 18 gauge galvanized binding wire and placing grills in position complete complying with standard specification and as directed.

BRICK WORK in cement mortor 1:5(one cement, five sand) using best quality Country bricks of size 8" 3/4"x4 ¼ x 2 ¾ “ for walls including cost of scaffolding curing, finishing etc., complete complying with standard specification and as directed by the departmental officers. In foundation and basement.

In Ground floor upto 4.50M height above basement

PLASTERING with cement mortor 1:5 (one cement and five sand) 12mm thick including mortar plasticizer at 200ml per 50 kg of cement used, cost of scaffolding, finishing, curing etc., complete complying with standard specification and as directed by the departmental officers.

Paving the flooring with self design Colour Ceramic tiles of size 305x305x6mm of approved quality and colour over a base layer of C.M.1:3, 20mm thick in all floors used 0.20 kg / m2 including finishing the joints and pointing flush with even surfaces etc., complete complying with standard specifications and as directed.. (The tiles should be got approved by the Executive engineer before use on works).

Dadooing the walls with colour printed Design glazed tiles of size 150mmx150mmx6mm of approved quality and colour over a base layer of C.M.1:2, 10mm and pointing the joints with white cement mixed with colouring pigment at the rate of 0.40 kg/sq.m neatly in all floors, curing etc., complete complying with standard specification and as directed by the departmental officers. (The tiles should be got approved by the Executive engineer before use on works).

Painting the walls with two coats ready mixed exterior / interior emulsion paint of first class approved quality and colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification and as directed.

Supply and erecting and hoisting of ISMB 350x140mm steel stanchion post including cleats to receive the purlin all cutting drilling holes welding and fixing of members with necessary bolts, nuts anchor bolt of approved quality hoisting aligning and glazing the trusses in position as per plan. The rate should include the cost painting the members with one coat or red oxide primer and zinc chromate etc., complete complying with standard specification and as directed by the departmental officers.

Fabricating and supplying and erecting the required number of Trusses with structural steel members like angle iron MS plates for all truss members including cleats to receive the purlins all cutting drilling holes welding and fixing of members with necessary bolts nuts anchor bolt of approved quality hoisting aligning and laying the trusses in position as per plan. The rate should include the cost of painting the members with two coats of synthetic enamel paint over one coat of red oxide primer etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and laying of High profile colour galvalume sheet (as per ISI Standard) with combination 55A1:43 4Zn:1:6SI of TCT bent type 0.47mm thick not less than 150 GSM and standard width of 1.06m with yield strength of 550 MPA made from high tensile/ CR sheets of approved quality for roofing with necessary fixing arrangements like 65m and long hexagonal head screws with EPDM rubber seal etc., complete, complying with standard specification and as directed by the departmental officer. (Test certificate for quality should be furnished on receipt of material at site)

Supply and fixing of continues sandwich Puf panels 50mm thick either as single piece Pre-fabricated, modular factory made units which consist of an insulating layer of rigid polyurethane loam between two layers of metal sheets, comprises of puf bonded between two sheets of Pre-coated G.I sheet of 0.5mm thick to produce straight to finish panels with all necessary fixtures to complete the work in all respects. The rate is inclusive of design, shop drawing preparation, submission for approval etc., and also inclusive of any other incidental charges such as lifting using grain, labour charges for erection, cost of all materials involved and as directed by the departmental officers.

Supplying and fixing of 40 X 6mm G.I Flat over the galvalume sheet roofing which is placed on the top of Purlin in the longitudinal direction to avoid the lifting of roofing during heavy wind. The rate is inclusive of GI screws 75mm length with rubber and aluminium washer, drilling hole over GI Flat to hold the sheet and purlin with necessary adhesive flashing tap directly over the galvalume sheet including labour charges for fixing, conveyance, loading, unloading and cutting etc. complete as directed by the departmental officers.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade) calcium carbonate and natural fibers (wood powder / rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water /moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-in-charge. (Note: stainless steel butt hinges and necessary S.S.screws shall be paid separately) 30mm thick.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/ Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), Calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position complete as per direction of Engineer-in-charge Frame size 65x100mm.

Stainless steel butt hinges 125x64x2.50mm.

Tower bolt 200x10mm.

Handle 125mm.

Fabricating supplying and fixing in position of Aluminium anodized natural colour matt finish of single leaf door with half paneled with 12mm thick both side laminated particle bord at bottom and half glazed using 5.50mm thick plain glass at top. The outer frame shall bewith aluminium box section 101.60x44.45x3.18m at 2.319kg/m and shutter frame made of section vertical & top rail : 50x44.45x2.50mm @ 1.292 kg/m, bottom rail : 100x44.45x2.50mm @ 1.974 kg/m, lock rail:50x44.45x2.5mm @ 1.292 kg/m, Alu. Clips : 17.15x17.27x1.50mm @ 0.176 kg/m, Alu Handle : 100x30mm @ 0.988 kg/m and necessary accessories such as aluminium clips, rubber beading PVC felt handle for a lengtjh of shutter (both side) locking arrangements, furniture, fittings such as aluminium tower bolts – 250 x 12mm – 1 No. aluminium tower bolts 200 x 12mm – 1 No. Aluminium Hydraulic door closer – 1 No. lock – 1 No. Door stopper with rubber bush including cost of materials labour charges and power consumption charges required for fabrication including chipping dismantling and making hole to the required extent in RCC columns, Beams or masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing as directed by the departmental officers . The Aluminium surfaces should be anodised with matt finish under electrically condition in accordance with IS specification 1868/1962 of Anodic thickness of not less than 15 microns (fifteen) for all sections . All the materials should be got approved by the Engineer incharge before fixing as directed.

Supplying and fabricating and fixing in position of mild steel door with double shutters using M.S.angle of size 40x40x6mm for outer frames and 35x35x5mm for shutter frames, with bottom 1/3rd M.S Sheets of 18 gauge with M.S flate of size 32.x6for internal stiffners and top 2/3rd grilled including one number of aldrop, two numbers of tower bolts, hold fast , hinges, handle etc., including two coats synthetic enamel paint over one coat of primer. The rate shall inclusive of cost of all materials.

Supplying and fixing(under lintel grove) cold rolled ROLLING SHUTTERS of approved quality of 18 gauge 7.5 cm wide cold rolled lathe section in one piece interlocked together with specially designed pipe shaft with adequate number of high tensile steel wire springs of approved quality complete with brackets side guides and arrangements for inside and outside locking arrangements with push and pull operations and pulling back handle with all accessories in best workmen ship and the entire shutter painted with two coats of best quality anti-corrosive paint over one coat of red oxide primer and clear opening of 1.80M width 2.60M height. The rolling shutter shall be placed below the lintel and behind the RCC curtain slab of 7.5 cm thick and 45 cm depth. Each rolling shutter shall be provided with one pair of approved quality of ball bearing complete. Rolling shutter should confirm to I.S.6248-1979and should be got approved by the Executive Engineer before fixing .[This specification consists of the following component materials required for erection of rolling shutter.(1).18 G 3" lathe section 1.90M long-29 Nos. (2)10 G guide channel 2.6Mlong-2 Nos.(3).13 G bottom plate for 1.8M long with angle.(4).M.S.pipe 40mm dia. C'class -2M long.(5).10SWG side plate 13"x12"-2 Nos.(6).2 SWG spring 3" bore. (7).'U'-clamp.(8).ball bearing suitable for 2 1/2 "pipe.(9).18 SWG clip suitablefor 4"lathe.(10).20 SWG M.S.sheet. Etc

Supplying and fixing UPVC (Un-Plasticized Polyviny Chloride ) windows of casement type (open) from the profile the size of outer frame 60mmx58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash an outer frame that enables opening of the window. The window should be fized to the wall the 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work.

Supplying and fixing of UPVC (Up-plasticized poly vinyl choloride) louvered ventilators of from the profile the size of outer frame 60mmx58mm and shutter profile size of 60 x78mm both profiles are reinforced with GI/ 1mm 125 GSM and 100% corrosion free, the profile are multi colored chamber section with wall thick of 2mm. The EPDM rubber (Black colour ) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiation pin headed glass 4mm thick should be provided to the louvers. The Ventilator should be fixed to the wall with 100% packing with screws silicon packing allround the frames. The Ventilator should got approved from the Executive Engineer before use on work.

Supplying and fixing M.S Grill to special windows and ventilators etc using 20mmx6mm angle including cost of MS grill, one of red oxide and fixing in position etc. complete complying with Standard Specification and as directed.

Supplying and fixing in position Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia CI pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Drilling of bore well of 150 mm dia including transportation from the place with in the above district in alluvial soil sedimentary strata of ckay and sand stone shale pebbles boulders etc by first taking pilot of 140mm/150mm/200mm dia and the enlarging to required dia by direct or revise rotary mud circulation method using contractor’s rig fuel labour drilling betonies mud and water required for the drilling at the site shown by the departmental officers upto 60M depth ending below ground level.

60m and upto 90M depth

90m and upto 120M depth

120m and upto 150M depth

Reaming from 140/150mm dia pilot bore to 300mm dia bore as directed by the departmental officers upto 60 M depth ending below Ground level.

60m and upto 90M depth

90m and upto 120M depth

120m and upto 150M depth

Supplying PVC casing pipe (with slot) 0f 160 mm dia plain pipe in 3M length each as per ISI 12818 / 1982 to suit deep bore for delivery at site including loading and unloading, freight, transit insurance etc., complete.

Supplying PVC casing pipe (without slot) 0f 160 mm dia plain pipe in 3M length each as per ISI 12818 / 1982 to suit deep bore for delivery at site including loading and unloading, freight, transit insurance etc., complete.

Supplying and fixing PVC bore well end cap of size 160/168mm dia of approved quality as directed by the departmental officers.

Labour charges for inserting 165/168 mm dia PVC casing pipe assembly (with slot or without slot) in the drilled hole including jointing the pipes with PVC coupler and cement paste etc.,, complete supplying and packing the annular space with pebbles of size and quality including conveyance is approved by the departmental officers.

Charges for developing the bore well for entire depth with suitable air compressor of 300RPM capacity (minium 8 hrs) including the transportation labour and fuel charges for conmpressor and directed by the departmental officers and conducting yield test by "V" notch methods, excluding the cost of bore charges and conveyance charges of handle boring.

Supplying and Erection of 3 H.P submersible pumpset confirming to IS-14220 with ISI mark 75x75 LPM X mts Suitable for 150mm bore well complete complying with standard specification including suitable 3-phase panel board with DOL with two level guard starter and accessories and labour charges for erection of submersible pump set in bore well including fixing and jointing the submersible cable(but excluding cost of 4sqmm -3core copper cable) with proper clamps,pressure gauges upto the exterior wall of panel board consisting of JPICN switch starter, voltmeter, ammeter, 3pilot(indicating) lamps capacitor,single phase preventometer,water level guard and laying and jointing the cable and twin earthing as per IE rules etc., complete and testing pump set on trail run for 3days etc., complete complying with standard specification.

Supply, laying and run of 2 of 7/20 PVC sheathed aluminum cable with polythene wire 10 guage stay wire etc., complete as directed by the departmental officers.

Supply and fixing the Nylon Rope to connect the submersible motor in borewell etc., complete.

Supply and fixing 32mm dia HDPE pipe for bore to connect the submersible bore etc., complete.

Supplying, and fixing PVC pipes of 20mm dia of approved quality and variety conforming to pressure IS 4985. The rate is inclusive of cost of pipe, all taxes, conveyance charges of materials and all other labour charges for fixing the PVC pipe as directed by the departmental officers etc., complete complying with standard specifications. The PVC pipe should be got approved by the departmental officers before use on work.

Supplying, and fixing PVC pipes of 25mm dia of approved quality and variety conforming to pressure IS 4985. The rate is inclusive of cost of pipe, all taxes, conveyance charges of materials and all other labour charges for fixing the PVC pipe as directed by the departmental officers etc., complete complying with standard specifications. The PVC pipe should be got approved by the departmental officers before use on work.

Supplying, and fixing PVC pipes of 32mm dia of approved quality and variety conforming to pressure IS 4985. The rate is inclusive of cost of pipe, all taxes, conveyance charges of materials and all other labour charges for fixing the PVC pipe as directed by the departmental officers etc., complete complying with standard specifications. The PVC pipe should be got approved by the departmental officers before use on work.

Supplying and fixing in position 20mm dia PVC Elbow of heavy duty of approved quality and good variety including cost of fixing charges necessary cutting and threading, jointing the Specials etc complete.

Supplying and fixing in position 20mm dia PVC Bend of heavy duty of approved quality and good variety including cost of fixing charges necessary cutting and threading of Pipes, jointing the Specials etc complete.

Supplying and fixing in position 20mm dia PVC Tee of heavy duty of approved quality and good variety including cost of fixing charges necessary cutting and threading of .Pipes, jointing the Specials etc complete.

Supplying and fixing in position 20mm dia PVC coupler of heavy duty of approved quality and good variety including cost of fixing charges necessary cutting and threading of .Pipes, jointing the Specials etc complete.

Supplying and fixing in position 25mm dia PVC Elbow of heavy duty of approved quality and good variety including cost of fixing charges necessary cutting and threading, jointing the Specials etc complete.

Supplying and fixing in position 25mm dia PVC Bend of heavy duty of approved quality and good variety including cost of fixing charges necessary cutting and threading of Pipes, jointing the Specials etc complete.

Supplying and fixing in position 25mm dia PVC Tee of heavy duty of approved quality and good variety including cost of fixing charges necessary cutting and threading of .Pipes, jointing the Specials etc complete.

Supplying and fixing in position 25mm dia PVC coupler of heavy duty of approved quality and good variety including cost of fixing charges necessary cutting and threading of .Pipes, jointing the Specials etc complete.

Supplying and fixing in position 32mm dia PVC Elbow of heavy duty of approved quality and good variety including cost of fixing charges necessary cutting and threading of .Pipes, jointing the Specials etc complete.

Supplying and fixing in position 32mm dia PVC Bend of heavy duty of approved quality and good variety including cost of fixing charges necessary cutting and threading of Pipes, jointing the Specials etc complete.

Supplying and fixing in position 32 mm dia PVC Tee of heavy duty of approved quality and good variety including cost of fixing charges necessary cutting and threading of .Pipes, jointing the Specials etc complete.

Supplying and fixing in position 32 mm dia PVC coupler of heavy duty of approved quality and good variety including cost of fixing charges necessary cutting and threading of .Pipes, jointing the Specials etc complete.

Supplying and fixing in position 15mm dia brass Pillar tap (heavy duty) of approved make confirming to IS specifications and quality including cost of shellac, thread, etc., complete as directed by the departmental officers.

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve of 32mm dia with ISI make including cost of shellac, thread balls, etc., complete.

Supplying and fixing in position best quality 75mm PVC soil / waste pipes of 110mm dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings etc., complete as directed by the departmental officers.

Supplying and fixing PVC ventilating shaft of 110mm dia (having working pressure 4 kg. / sq.cm) with 3 metre height including cost of PVC cylindrical cowl of best approved quality etc., complete as directed by the departmental officers.

Supplying and fixing Brass Chromium platted Towel Rail 600mm Long and 20mm diameter with brackets of same materials including cost of teak wood plugs, CP Screws etc., complete complying with standard specification as directed by departmental officers.

Supply and fixing in position wash hand basin with new one fixing in position best quality approved make white glazed earthenware wash hand basin of size 550x400mm with a pair of cast iron brackets, including cost of 15mm dia metre brass chromium plated pillar tap, 32mm dia metre G.M wheel valve 15mm dia brass nipple 15mm dia nylon connection etc., including fixing the wash hand basin in the wall in position with pair of CI brackets with teak wood plugs and screws and giving necessary water supply connection and painting the brackets with two coats of paint over a primary coat of anticorrosive paint including testing for leakage etc., complete complying with standard specification.

Supplying and fixing in pofsition of best Indian make PVC Water Tank of 1000 litres capacity confirming to ISI standards as directed by the departmental officers including cost of material and conveyance charges of material to work site etc., complete complying with standard specifications.

Painting new iron works with two coats of synthetic enamel paint of approved quality and colour over the red oxide primer in all floor including cost of scaffolding, brushes etc., complete complying with standard specification and as directed.

Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality including raising the elevated portion around the manhole to accommodate manhole cover with brick work in Cement mortar 1:3 etc., complete as directed by the departmental officers.

Supplying and fixing fine polished cuddapah slab of 25mm thickness for cup-board arrangements including laying to correct alignment with necessary cement mortar and black powder etc, complete complying with standard specification and as direct.

COLOUR WASHING two coats over one coat of white washing using best shell lime including cost of gum, Kanjee , brushes colouring pigment approved by the officer and finishing complete complying with standard specification and as directed.

Supplying and fixing of M.S Gate in two leaves with B Class pipe of size 50mm dia pipe alround and 15cm dia pipe vertically at 15cm intervals including fixing of 18 gauge M.S.Sheet at bottom / middle of gate 50cm height including cost of all furniture fittings, aligning, fixing in position with two coats of anti corrosive metallic nut brown colour paint over one coat of primer etc., complete complying with standard specification and as directed by the departmental officers. Main gate of size 6.00m x 2.10m

Wicket gate 1Mx2.10M

Sectioning and levelling the site by using JCB machinery including hire charges, fuel etc., complete.

Please Enable Macros to View BoQ information