Re-Invite - Special Repair of PHC Building in Palam Vihar (sector-23) in Gurugram District.

Amount

Earth work in excavation in foundations, trenches, etc. in all kinds of soils, not exceeding 2 meters depth including dressing of bottom and sides of trenches stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm layers with compaction, including disposal of all surplus soil, as directed with in a lead of 30 meters. (HSR. 6.6)

Earth filling under floors with tibba sand non plastic under floors with good earth taken from outside of campus area with all lead and lift including loading, unloading, laid in 15 cm layer including ramming, watering, consolidating, compaction, and compensation of earth etc. complete in all respect as per the direction of engineer in charge (For any lead lift) (N.S Items)

Dismantling Brick Work, Tile Masonry or Tile Lining and Tile Terracing-In cement (HSR-8.5 b)

Centring and shuttering for reinforced cement concrete north light folded Plate roofing including all components of folded plates and including Diaphragm beam.(HSR-9.2)

Cement concrete 1:4:8 with stone aggregate 20 mm nominal size in foundation and plinth (HSR 10.38)

Cement concrete 1:4:8 with stone aggregate 40mm nominal size in foundation and plinth [HSR 10.39]

First class brick work laid in cement sand mortar 1:6 in first storey upto 4 meters above plinth level (HSR 11.7)

Cement concrete 1:11/2:3 with stone aggregate 20 mm nominal size for reinforced concrete work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centring and shuttering, laid in position, complete in all respects. (HSR 10.82 + 10.95 (a)

Terracing consisting of tiles 22.86 cm x 11.43 cm x 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and another layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 kg per sqm on top of RCC slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13)

Base course of floors consisting of 100 mm thick cement concrete 1:8:16 and 100 mm sand or stone filling (HSR 14.1)

Plastering on walls 12 mm thick cement plaster 1:4 (HSR 15.5)

Providing & Fixing Vitrified Tiles 600mm x 600mm of approved make in flooring laid in any pattern as specified over base of 20 mm thick cement coarse sand morter 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like: NITCO, KAJARIA , SOMANI, ORIENT BELL, JOHNSON, RAK & SIMPOLO.(HSR-14.89)Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Providing & Fixing Ist Quality ceramic glazed wall tiles conforming to IS. 15622 ( thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry including ointing in white cement mixed with pigment of matching shades complete. (a) size of ceramic glazed tiles 200 x 300 mm of reputed manufacturer like:- NITCO, KAJARIA , SOMANI, ORIENT BELL, JOHNSON, RAK & SIMPOLO shall be used as approved by Engineer-in-charge (HSR 14.92) (a) Note:- Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Factory manufactured solid flush door shutters with block board core as per I.S no. 1659-1669 bonded with water proof type phenol formaldehyde synthetic resin, hot-pressed, conforming to I.S 2202 part-I anf II fixed in position, including iron hinges, screws, chocks/cleats, and stops etc. (Excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position) -(Note) : - Commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminatyed core and lipped edges. (Duro, green) 35 mm thick (HSR 17.93) (a) (iii))-Note I under 17.18.

Supplying and fixing glass panes including special metal sash putty of approved make (b) glass panes 4 mm thick exceeding 40 sq.m areas. Modi, Saintgobain (HSR 18.30 B)

Scraping-White wash and colour wash (HSR-8.32 a )

Providing & applying Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (Note:- First quality paint of reputed make firm such as goodlass- Neolac, Berger, Garware, Jenson, Nicholson, Asian & shalimar shall be used as approved by Engineer-in-charge in writing, drum of paint shall be opened in presence of Engineer-in-charge. (HSR 16.3)Through Rate

Distempering with washable oil bound distemper (of approved manufacture) two coats on old distempered work.(HSR-16.60) (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, drum of paint shall be opened in presence of Engineer-in-charge).Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Finishing walls with exterior decorative cement based paints such as snowcem Robbiacem etc on new work, two coats to give an even shade (HSR 16.61)Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.Ground Floor

11.43 cm thick brick wall 1:4 laid in cement (HSR-11.46)

Corrugates asbestos sheet roofing 7 mm thick sheets fixed with G.I hooks and bolts, limpet and bitumen washers complete, fixed in position, excluding the cost of purlins, rafters and trusses.(HSR-13.19)

Plastering on wall 15 mm thick cement plaster 1:6 on the rough side of single or half brick wall 1:6 (HSR 15.12)

Providing & Applying priming coat with metal primer on new steel or iron work including preparation of surface, painting on mettalic surfaces etc. (Note:- First quality paint/primer of reputed make firm such as goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & shalimar shall be used as approved by Engineer-in-charge in writing, drum of paint shall be opened in presence of Engineer-in-charge) (HSR 16.9) Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Providing & applying Painting two coats excuding priming coat with ready mixed paint for metelic surfaces in all shades on new steel or iron work (Note:- First quality paint of reuted make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, drum of paint shall be opened in presence of Engineer-in-charge) (HSR 16.17) Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

WHITE WASHING--Three coats (HSR-16.48)

Wrought iron and mild steel (using angles, flats, square bars, tees and channels), ladders, grills gratting frames, window guards, iron doors openable or fixed staircase or parapet or any other type of railing, gates and tress guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position (HSR 18.12)

Pressed steel sheet frames (chowkats), consisting of 2 mm thick steel sheet of the specified sections, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving--door and window frame of size 76 mm X 38 mm with 35 mm wide single rebate (HSR-18.34 b)

Steel reinforcement TMT steel bar FE-550 EQR/FE-500 D grade or more for RCC work, where no included in the complete rate ofRCC including stairghtening, bending, binding, wastage, overlaps, welded joints, spacer, bars, chairs, stays, hangers and annealed steel wire etc.and placing in position complete in all respect for all heights/depts/story/basement etc. (HSR-18.22) (Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work, excluding overlaps. From the length so measured, the weight of reinforcement shall be calculated in tones on the basis of IS:1732.Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing, shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement).

Providing and fixing in position best Indian make (to the approval of the Engineer-in-charge). Indian type orissa or orya water water closet suite for sinking into floor, with raised foot treads complete with 100 mm HCI 'P' trap with or without vent as required and all other necessary fitting as fully described in item no. 30.1. (HSR-30.2)a) Size 580mm (i) White.Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Providing and fixing in position best Indian make European type water closet suite with concealed 'P or 'S trap with or without vent (as approved by the Engineer-in-charge) and all other necessary fitting as fully described in item no. 30.3 above. (HSR-30.6)(i) whiteNote:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Providing and fixing 15 liters capacity low level vitreous china ware cistern complete with flush bend all other necessary fitting instead of C.I high level cistern complete with fitting.(HSR-30.12)(i) white

Providing and fixing best indian make plastic hygenic seat with lid complete instead of hollow black or white plastic seat and lid (HSR 30.13)(i) white plastic seat (solid)

Extra for providing and fixing 32 mm dia. G.I/C.P flush pipe complete with accessories. Instead of 32 mm dia galvnised telescopic flush pipe with clips (as required by the Engineer-in-charge) (HSR-30.15) (a) 32 mm G.I flush pipe

Providing and fixing in position best indian make flat black or angular lipped front urinal 465 mm high consisting of:-(HSR-)Flat black lipped or angular urinal basin of VITREOUS CHINA WARE (to the approval Of the Engineer-in-charge) i(White)

Providing & fixing in position best Indian make white lavatory suites (with full anti splash rim in vitreous chinaware and all other necessary fittings as fully described in item no. 30.41 above (HSR-30.42)

Providing and fixing in position 32mm dia G.I waste pipe embedded in wall or lead waste pipe (weighing 3.47 kg. per metre and 2.8 mm thick) upto floor level including cost of wipped solder joint etc. complete (as required by the Engineer-in-charge) (HSR-30.48)

Providing and fixing in position best quality stainless steel sinks with complete fittings as fully described in utem no 30.51 above (HSR-30.53)a) 600 mm x 450 mm x 200 mm

Providing and fixing in position glass shelf fixed in with rawl plugs with C.P brass screws complete including cutting and making good the walls etc. (HSR-30.69 (a)--c) Vitreous chinaware shelf 560mm long i) white.

Providing and fixing in position best Indian make bevelled edge 5.5 mm thick mirror mounted on asbestos sheet ground fixed in position by means of 4 nos. chromium plated brass screws and washers over rubber washers and rawl plug embeded in the wall or chromium plated brass clamps with C.P. brass screws (as required by the Engineer -in -charge) complete including cutting and making good the walls etc. (HSR-30.71)a) Indian make (I) 600mmx450mm

Providing and fixing in position 15 mm I/d C.P. brass bib cocks of best quality (as required by the engineer I charge)(HSR-30.75)(a) Bib cock long body

(c) Bib cock

Providing and fixing in position C.P brass stop cocks (as approved by the Engineer-in-Charge)(HSR-30.76)--a) 15mm stop cock --i) Stop cock male and female end.

ii) Concealed stop cock with flange

Providing and fixing in position best indian make flexible tube connection (HSR-30.82)-b) C.P brass i) 15mmx300mm.

Providing and fixing in position H.C.I soil waste vent or antisyphonage pipes to I.S.I specification of E.L.C manufacture or of any other reputed firm including cutting and wastage etc. and cutting holes in walls, roofs or floor etc. and making good to its original condition but excluding cost of lead jointing(HSR-30.84)100mm internal diameter

75mm internal diameter

Providing lead caulked joints to H.C.I pipes and specials conforming to I.S.I specification of E.L.C manufacture or any other reputed firm including cost of lead yarn, fuel and tools etc.(HSR-30.87)100mm internal diameter (1.13kg)

75mm internal diameter (0.91kg)

Providing and fixing in position M.S or heavy flat iron clamps made out of M.S flat not less than 5 mm of the approved deign for fixing C.I soil waste vent or anti pipes to walls complete in all respects including cutting and making good the walls and floors etc. and painting.(HSR-30.88)For 100 mm internal diameter pipes

For 75 mm internal diameter pipes

Providing and fixing HCI floor traps ISI marked of the self cleaning design with C.P brass hinged grating with frame with or without vent arm and including cement concrete 1:2:4 under and around the floor trap where required upto floor level complete in all respects including cutting and making good the walls and floors etc. minimum depth of water should be 150 mm with a minimum seal of 50mm (HSR-30.89)b) With 75mm I/d outlet.

Providing and fixing in position H.C.I. special for soil, waste, vent or anti-syphonage pipes to I.S.I marked including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead jointing (HSR-30.91)-(a) 100mm i/d pipes--(i) Heal rest bend

(xiii) Bend with door

(xxii) Collars

(xxiv) c) WC connection 300mm long

(b) 75mm (xiii) Bend with door

(xiv) Bend Plain

(xviii) Collars

Providing and fixing in position gully traps fixed in cement concrete 1:4:8 complete with H.C.I. grating 150mm x 150mm cast iron cover weighing approximately 7.26kg and frame clear opening 300mmx300mm and outside size 330mmx330mm and chamber including cost of all brick work in cement mortar 1:5 cement concrete 1:8:16 in foundation, and cement concrete 1:2:4 in coping around C.I cover and frame etc. with three coats of black bitumastic superior paint of approved manufacture on all C.I work as per standard design, minimim depth of water should be 150mm with a minimum seal 50mm (HSR-30.114)a) 100mm internal diameter S.W gully trap.

Providing and fixing HDPE water storage tanks of sintex, Diplast, O.K. supreme make with covers/lids marked with IS:12701 on roof top of buildings including cost of hoisting and placing Iin position, making connections with inlet and outlet pipes, providing overflow and scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction to the Engineer. (HSR-30.119)----1000 Ltr. Cap.

Providing and fixing HDPE water storage tanks of sintex, Diplast, O.K. supreme make with covers/lids marked with IS:12701 on roof top of buildings including cost of hoisting and placing Iin position, making connections with inlet and outlet pipes, providing overflow and scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction to the Engineer. (HSR-30.119)----500 Ltr. Cap.

DSR Items :- Providing and fixing G.I pipes complete with G.I fitting and clamps, i/c cutting and making good the wall etc. internal work -Exposed on wall (DSR-18.10)--(i) 15 mm internal diameter of pipeline Make:- UNIK, TATA, ZOLOTO.

20 mm internal diameter of pipeline

25 mm internal diameter of pipeline

40 mm internal diameter of pipeline

Providing and fixing G.I pipes complete with G.I fitting and clamps, i/c making good the wall etc concealed pip including painting with anti corrosive making good the wall (DSR-18.11)15 mm internal diameter of pipeline Make:- UNIK, TATA, ZOLOTO.

20 mm internal diameter of pipeline

Providing, Fixing gun metal peet valves with C.I wheel of approved quality (Screwed end) (DSR-18.17) 20 mm nominal bore-Make:- UNIK, TATA, ZOLOTO.

25 mm nominal bore

40 mm nominal bore

Providing & fixing G.I Union in G.I pipe including cutting and threading the pipe and making long screws etc complete (New work) DSR-18.46) 15 mm internal diameter-Make:- UNIK, TATA, ZOLOTO.

20 mm internal diameter

25 mm internal diameter

40 mm internal diameter

Recovery Items:-Bidder have to quote rate for recovery items at least or more than reserve price. The rate quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency.T Note:- The reserve rate/amount is minimum amount to be used as base for quoted purchase rate by the agency. No rates/amount below the reserve price will be entertained and reserve price will be considered for all purposes in case the agency quotes lesser than reserve price.--Tile @ 5.00/-Each

Brick bats @ 400/-per cum