CWE(U)/D-06/2021-22

Amount

Supply,Installation testing and commissioning of Factory made LT panel board indoor type, dust & Vermin proof fabricated out of 2.00 mm thick CRCA sheet fixed with Angle iron frame of size 40x40x5mm duly powder coated complete using lugs,and glands of cable connection and having epoxy coated copper bus bar of size 40 x 6 mm, 4 strips for 3 phase and neutral 415 Volts,50Hz mounted on epoxy insulators, prewired with suitable size of PVC insulated multi strand copper conductor cable having independent enclosure for incoming and outgoing electrical connection and cable gland at bottom for incoming and outgoing and locking arrangement on front side and taking down existing LT panel complete all as specified and directed by Engineer in Charge including following fittings and fixtures as mentioned below (a) MCCB 400 Amp, Four pole, 415 Volts, 50 HZ 50 KA -01 No. (as incoming) (b) MCCB 200 Amp, Three pole, 415 Volts, 50 HZ 35 KA -02 Nos. (as outgoing) (c) MCCB 100 Amp, Three pole, 415 Volts, 50 HZ 25 KA -02 Nos(as outgoing)

Supply and fixing of Non clogging Submersible pumping set 20 HP, Horizontal type, 3 phase casing single delivery having main discharge 1500 lit /minute at 20 mtr head with SS impeller, Shaft and CI body, non-clog to pass 40 mm size particles including Supply, installation using guide rail and lifting chain complete. Model:-KRTK-100-315.

Supply and fixing of Centrifugal Pump set horizontal type split casing complete with electric motor of 75 HP, 415 Volts 3 phase, 50 Hz, AC supply, 1450 RPM capacity 50 LPS at 80 mtr head inclusive of Supply and installation of coupling and coupling guard and base frame complete.

Supply and fixing of Submersible pump, electric driven 415 V, TP suitable for 200/250 mm dia bore well ( Casing pipe size 200/250 mm) supply and Install complete upto 5 HP having 9m3/hr at 88 mtr head complete all as specified and directed.

Supply and fixing of Submersible pump, electric driven 415 V, TP suitable for 200/250 mm dia bore well ( Casing pipe size 200/250 mm) supply and Install complete upto 7.5 HP having 13m3/hr at 86 mtr head complete all as specified and directed.

Supply and fixing of Submersible pump, electric driven 415 V, TP suitable for 200/250 mm dia bore well ( Casing pipe size 200/250 mm) supply and Install complete upto 10.0 HP having 14m3/hr at 100 mtr head complete all as specified and directed.

Supply and fixing of Submersible Monoblock pump set suitable for 415 V ,3 phase system capacity 7.5 HP having discharge 110 at 55 mtr head complete all as specified and directed.

Disconnecting Electric connections from LT Control pannel and starter of submersible pump set of any size 5HP to 20 HP and removing the pipe line connections from discharge side and taking out submerssible pump set along with, column pipe from bore well with the help of chain pully block including transportation to workshop for repair and lowering of same pump in bore well after repair including replacement of rusted nuts bolts, rubber gasket complete, all as specifeid and as directed by Engr-in-charge.

Labour for opening the submersible pump set, repairing, rewinding and assembling the pump set including insulating material of any size 5HP to 20 HP capacity complete all as specified and as directed by engr-in-charge make KSB, BS and Great India. ( Copper winding wire and other spare parts required for repairing will be measured under relevant item of Sch 'A')

M&L for rewinding of Submersible pump set 5 - 10 HP including super enameled copper winding wire of suitable size not less than original after cutting and taking out old winding complete with all insulation material such as Cotton top varnish etc of submersible pump set motor complete all as specified and as directed by the Engineer-in-Charge

M&L for rewinding of Submersible pump set 12.5 - 20 HP with super enameled copper winding wire of suitable size not less than original after cutting and taking out old winding complete with all insulation material such as Cotton top varnish etc of submersible pump set motor complete all as specified and as directed by the Engineer-in-Charge.

M & L Painting of submerssible pump set with two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in replacement of MS flange heavy duty including welding etc of size 50 x 300 mm complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in replacement of MS flange heavy duty including welding etc of size 80 x 300 mm complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in replacement GI Column pipe 50 mm bore of 3 meter length Heavy duty duly flange welded on both ends. Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement GI Column pipe 80 mm bore heavy 'C' class of 3 meter length, Heavy duty flange welded on both ends Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of submersible copper cable of size 2.5 Sq mm 3 core, 1100 Volts Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of submersible copper cable of size 4.00 Sq mm 3 core, 1100 Volts Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of submersible copper cable of size 6.00 Sq mm 3 core, 1100 Volts Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement moulded case circuit breakers, 3 pole, 63 Amps with breaking capcity 10 KA , 415 volts,complete all as specified and as directed.

Supply and fixing in replacement moulded case circuit breakers, 3 pole,100 Amps with breaking capcity 10 KA , 415 volts, complete all as specified and as directed.

Supply and fixing in replacement 3 pole power contractor ML-1.5, 25 Amps suitable for fixing in existing panel complete all as specified and as directed.

Supply and fixing in replacement 3 pole power contractor ML-2, 32 Amps, 415 Volts, 50 HZ suitable for fixing in existing panel complete all as specified and as directed. Make :- L&T or equivalent in Siemens/ ABB/ HAVELL'S .

Supply and fixing in replacement 3 pole power contractor ML-3, 40 Amps, 415 Volts, 50 HZ suitable for fixing in existing panel complete all as specified and as directed.

Supply and fixing in replacement 3 pole power conductor ML-4, 70 Amps, 415 Volts, 50 HZ suitable for fixing in existing panel complete all as specified and as directed.

Supply and fixing in replacement thermal over load relay, type ML 1 relay, range upto 16 Amp complete all as specified and as directed.

Supply and fixing in replacement thermal over load relay, type ML 2/3 relay, range upto 42 Amp complete all as specified and as directed.

Supply and fixing in replacement 3 pole power contractor MNX-18, 32 Amps, 415 Volts, 50 HZ suitable for fixing in existing panel complete all as specified and as directed.

Supply and fixing in replacement 3 pole power conductor MNX-25, 45 Amps, 415 Volts, 50 HZ suitable for fixing in existing panel complete all as specified and as directed.

Supply and fixing in replacement 3 pole power conductor MNX-32, 55 Amps, 415 Volts, 50 HZ suitable for fixing in existing panel complete all as specified and as directed.

Supply and fixing in replacement thermal over load relay type MN2, relay range 6-10 Amp, complete all as specified and as directed.

Supply and fixing in replacement thermal over load relay type MN2, relay range 9-15 Amp, complete all as specified and as directed.

Supply and fixing in replacement thermal over load relay type MN2, relay range 14-23 Amp, complete all as specified and as directed.

Supply and fixing in replacement thermal over load relay type MN2, relay range 20-33 Amp, complete all as specified and as directed.

Supply and fixing in replacement fully automatic star-delta starter in sheet enclosure type ML-1.5, FASD, relay max range 13-21 Amp including timer complete all as specified and as directed.

Supply and fixing in replacement fully automatic star-delta starter in sheet enclosure type ML-2 , FASD, relay max range 20-32 Amp including timer relay complete all as specified and as directed.

Supply and fixing in replacement fully automatic star-delta starter in sheet enclosure type ML-3 , FASD, relay max range 28-42 Amp including timer relay complete all as specified and as directed.

Supply and fixing in replacement single phase preventor, type VSP-II complete all as specified and as directed.

Development of borewell/ tube well with air compresser of rating 450 CFM with pressure line at 6 to 8 Kg per Sqcm complete all as specified and as directed. Note:- Rate quoted deemed to inclusive of necessary transportation of compressor & DTH/Rotary ring etc including other T&P required.

Development of borewell/ tube well with air compresser of rating 620 CFM with pressure line at 6 to 10 Kg per Sqcm complete all as specified and as directed. Note:- Rate quoted deemed to inclusive of necessary transportation of compressor & DTH/Rotary ring etc including other T&P required.

Material and labour for Fishing out the submersible pump set along with column pipe and submersible cable of any type, capacity by means of contractor's own different fishing out tools and connecting items complete all as specified and as directed. Note:- Payment of this item will be made after fishing out of complete pump set, submersible cable and column pipe etc and if any of items is not fished out, no payment will be made.

Supply and fixing in replacement of mild steel nuts, bolts & washers etc of any size complete all as specified and as directed.

Material and labour for replacement of rubber packing suitable for flange 40mm to 50 mm dia complete all as specified and as directed .

Material and labour for replacement of rubber packing suitable for flange 80 mm dia complete all as specified and as directed .

Supply and fixing in replacement of well cap suitable for 150 mm to 200 mm bore pipe consisting of two parts complete with welding and machinery work having provision of cut out for passing of column pipe and fabricated out of mild steel sheet 3.15 mm thick complete all as specified and as directed .

Supply and fixing in replacement of well cap suitable for 250 mm to 300 mm bore pipe consisting of two parts complete with welding and machinery work having provision of cut out for passing of column pipe and fabricated out of mild steel sheet 3.15 mm thick complete all as specified and as directed .

Supply & laying cable XLPE insultated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) with stranded aluminum conductor, 1100 volts grade of size 3.5 core 120 Sq mm including taking down the existing from site complete all as specified and directed by Engr-in-Charge.

Supply & laying cable XLPE insultated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) with stranded aluminum conductor, 1100 volts grade of size 3.5 core 70 Sq mm including taking down the existing from site complete all as specified and directed by Engr-in-Charge.

Supply & laying cable XLPE insultated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) with stranded aluminum conductor, 1100 volts grade of size 3.5 core 50 Sq mm including taking down the existing from site complete all as specified and directed by Engr-in-Charge.

Supply & laying cable XLPE insultated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) with stranded aluminum conductor, 1100 volts grade of size 3.5 core 35 Sq mm including taking down the existing from site complete all as specified and directed by Engr-in-Charge.

Supply & laying cable XLPE insultated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) with stranded aluminum conductor, 1100 volts grade of size 3.5 core 25 Sq mm including taking down the existing from site complete all as specified and directed by Engr-in-Charge.

Supply & laying cable XLPE insultated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) with stranded aluminum conductor, 1100 volts grade of size 4 core 16 Sq mm including taking down the existing from site complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of feeder pillar outdoor type made out of CRCA comprising of aluminium bus bar of capacity 400 Amps 4 strip and cabinet for housing MCCBs, metering equipments, all accessories prewire with copper cable of suitable capacity. All MCCBs should be connected with aluminium busbar as per there capacities and comprising of following accessories (main panel) (a) MCCB 4 pole 160 Amp, 25 KA (as in coming) -01 (b) MCCB 4 pole100 Amps, (as outgoing)-02 nos (c) MCB TP 32 Amps,10 KA-02 nos (d) MCB DP 32 Amps,10 KA-02 nos (e) Set of Indicating lamp (one set) (f) Supply and fixing fully automatic star-delta starter in sheet enclosure type ML-1.5, FASD, relay max range 13-21 Amp including timer relay for automatic start and stop, single phase preventer, phase sequence corrector, over load protection, earth fault protection, etc -02 No.

Supplying, installing, testing and commissioning of busbar chamber made of CRCA sheet with aluminium busbar of 400 amp capacity 4 strips, with MCCB of capacity 100 amps fixed inside busbar chamber including provision of foundation for busbar chamber with 600 MM clear space below for working. The busbar should be provided with cable entry box below for entering of cable of size upto 120 sqmm 3.5 core(one incomming and two out going) including proper thimbling to both input and output cables and taking down the existing from site complete all as specified and directed by Engr-in-Charge.

Excavation in trenches not exc 1.5 M wide and not exc 1.5 M in depth for pipe line, etc in soft/ loose soil getting out and levelling of bottom surface to required level all as specified and as directed.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick complete all as specified and as directed.

Removing excavated material from site to a distance not exc 50 mtr away and depositing where directed not exc 1.5mtr from the starting point all as directed.

Material and labour for sub class ‘B’ bricks old size, for cable protection, laid dry, flat over cable, perpendicular across the cable in trenches complete all as specified and as directed.

Material and labour for Sand cushioning with clean and sharp fine dry sand in trenches, for cable protection complete all as specified in clauses 19.75 of MES schedule part-I and directed.

Material and labour for plate earthing with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.5 meter below normal ground level, connected to galvanised earth lead 32mm x 6mm strip by means of bolts, nuts, check nuts and washer of galvanised iron steel all surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides,earth strip incased in 40 mm bore GI medium grade pipe, inclusing providing watering pipe 20mm bore GI pipe, medium grade from bottom of the earth pit to the top of the electrode complete with earth pit in PCC 1:2:4 type B1 using 12mm graded crushed stone aggregate, earth work and RCC cover complete all as specified and shown in electrical plate number 3 of SSR part-1 complete all as specified and as directed.

Supply and fixing earth continuity conductor or main earthing strip of size 32x6mm of galvanised iron for fixing to panels complete as specified and directed.

Ridhi engineers and builders

Rahul Enterprises