Addition,Alteration And Renovation of New Block Circuit House at Circular Road,Ranchi

Amount

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, leveling & dressing & finishing the top smooth.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size) derived from natural sources.

Centering and shuttering including strutting, propping etc. and removal of form for :

Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick

Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick

Providing Tor steel reinforcement of 8mm. dia rods as per approved design and drawing including cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position (excluding carriage of M.S. bars to work site) all complete as per building specification and direction of E/l. TMT Fe 500 (only vailid for Tata (tiscon), SAIL, JSPL, Electrosteel ltd Bokaro and Vizag(RINL))

Providing Tor steel reinforcement of 10mm. rods as per approved design and drawing including cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position (excluding carriage of M.S. bars to work site) all complete as per building specification and direction of E/l. TMT Fe 500 (only vailid for Tata (tiscon), SAIL, JSPL, Electrosteel ltd Bokaro and Vizag(RINL))

Providing Tor steel reinforcement of 12mm. dia to 32mm. rods as per approved design and drawing including cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position (excluding carriage of M.S. bars to work site) all complete as per building specification and direction of E/l. TMT Fe 500 (only vailid for Tata (tiscon), SAIL, JSPL, Electrosteel ltd Bokaro and Vizag(RINL))

Providing designation 75 A brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to2.5 including providing 10 mm thick mortar joints cost of screening materials , scafolding , raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/l. Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

Extra for providing and placing in position 2 Nos. 6 mm dia. M.S. bars at every third course of half brick masonry.

Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished) machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab over 0.5 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work

Extra for fixing marble /granite stone over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/ Granite/ stone work including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing wood work in frames of false ceiling, partitions, paneling, ledge etc. sawn and fixed in position with necessary stainless steel screws etc. Kiln seasoned and chemically treated hollock wood

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Sal wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Providing & Fixing decorative high pressure laminated sheet of plain /wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS :2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 2nd class teak wood 50x12 mm

Providing and fixing carbon steel galvanised (minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 m dia polyamide PA 6 grade sleeve, including drilling of hole in frame, concrete/ masonry, etc. as per direction of Engineer-in-charge. 10X120mm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm

Providing and laying double charge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622/ ISO 13006, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/ sqm including grouting the joints with white cement and matching pigments etc., Size of Tile 600x600 mm

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long,

the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l. 1:4 (1 cement : 4 fine sand)

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand).

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer

Painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Providing and applying 12 mm thick (average) premixed formulated one coat gypsum lightweight plaster having additives and light weight aggregates as vermiculite/ perlite respectively conforming to IS: 2547 (Part - 1 & II) 1976, applied on hacked / uneven background such as bare brick/ block/ RCC work on walls & ceiling at all floors and locations, finished in smooth line and level etc. complete.

Polishing in high gloss/matt finish melamine clear polish on wood work in required color/dooden shade texture with following process in the sequence as detailed below: 1. The surface to be polished in rubbed with sand paper 80/120 no and then with sand paper of 160/180 nos 2. Applying two coats of sealer with spray gun and allowing sufficient drying time for Ist coat and 2nd coat is allowed to dry for 8 to 12 hrs.

3. On drying of scaler coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done and this surface is further allowed to dry for 12 hrs.

4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrsz then this dry surface is again fine wet rubber smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer in Charge (Final coat to be done in 1 or 2 layers without gap of time)

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. UPto 5mm depth and 5mm width

Providing and fixing glazing in aluminium/ upvc door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 8 mm thickness (weight not less than 20 kg/ sqm)

Providing and fixing casement handle made of zinc alloyed (white powder coated) for uPVC casement window with necessary screws etc. complete.

Providing and fixing steel roller for uPVC sliding window with necessary screws etc. complete. each 88.75

Providing and fixing steel (white power coated) crescent lock for uPVC sliding window/ door with necessary screws etc. complete. each 167.70

Providing and fixing factory made uPVC white colour sliding glazed window above 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads, uPVC extruded interlocks and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle on one side of extreme panel along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) touch lock with hook (if required for wire mesh panel), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 2.50 sqm upto 4.00 sqm.) sqm 6861.60

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/6 litre (adjustable to 4 litre/8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15 mm nominal bore

Providing and fixing toilet paper holder : C.P. brass

Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/I.

Mirrors of 6mm thick plate glass bevelled edge mirror including C.P.brass revolving fittings 3mm ply wood board and C.P. hinges to fix with mirror. 600mm x 450mm size.

C.P. brass liquid soap container.

Providing and fixing PTMT Bottle Trap for Wash basin and sink. Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms

Providing and fixing 15mm size C.P. brass pillar cock (Weight not less than 350gms).C.I. body brass spindle pillar cock of approved quality as per specification and direction of Engineer-in Charge. C.P. body brass spindle.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.

20 mm dia nominal bore

25 mm dia nominal bore

32 mm dia nominal bore

40 mm dia nominal bore

50 mm dia nominal bore

Providing and fixing gun metal fully way valve of approved quality all complete as per specification and direction of etc.

20mm dia and weight not less then 400gms

25mm dia and weight not less then 500gms

32mm dia and weight not less then 700gms

40mm dia and weight not less then 1.0kg.

50mm dia and weight not less then 1.5kg.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 15 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm dia

Providing and fixing on wall face unplasticised Rigid PVC rain water and waste pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm outer dia

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Coupler 110 mm

Single pushfit Coupler 110 mm

Single tee with door 110x110x110 mm

Single tee without door110x110x110 mm

Bend 87.5° 110 mm bend

Shoe (Plain) 110 mm Shoe

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors: (F.T. + U.T.) 100 mm inlet and 100 mm outlet

Point wiring in PVC conduit, with modular type switch :- Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 Sq.Mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular type switch, modular plate,suitable GI box etc. as required. Group C

Twin Control Point wiring in PVC conduit, with modular type switch :- Wiring for twin control light point with 1.5 Sq.Mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, 2 way modular type switch, modular plate,suitable GI box etc. as required.

Power plug wiring in PVC conduit (2 x 4 Sq.Mm.) :- Wiring for power plug with 2 x 4 Sq.Mm. FR PVC insulated, copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 no 4 Sq.Mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Circuit / Sub main wiring in PVC conduit :- Wiring for circuit / submain wiring alongwith earth wire with the following sizes of PVC insulated, copper conductor single core cable in surface/ recessed PVC conduit as required.

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire.

2 x 6 sq.mm. + 1 x 6 sq.mm. Earth wire.

2 x 10 sq.mm. + 1 x 6 sq.mm. Earth wire.

4 x 6 sq.mm. + 2 x 6 sq.mm. Earth wire.

4 x 10 sq.mm. + 2 x 10 sq.mm. Earth wire.

4 x 16 sq.mm. + 2 x 16 sq.mm. Earth wire.

S/F light plug point Modular type accessories :- Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps. modular Type Switch, connection, painting etc. as required.

S/F power plug point modular type accessories :- Supplying and fixing of suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps. modular switch, connection, painting etc. as required.

Supplying and fixing of following modular switch/ socket outlet on the existing Modular plate & switch including connection but excluding modular plate etc. as required.

5/6 amps switch

3 pin 5/6 amp socket outlet

15/16 amp switch

6 pin 15/16 amp socket outlet

Supplying and fixing following size/ modules, GI box Boxes alongwith modular base & cover plate for modular switches in recess etc as required.

1 or 2 Module (78mmX78mmX45mm)

4/5 Module (78mmX140mmX50mm)

6 Module (78mmX205mmX50mm)

8 /9Module (78mmX230mmX60mm)

12 Module (135mmX205mmX60mm)

Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A, “C” curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

SSupplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

S/F Modular type electronic fan regulator :- Supply and fixing of stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

S/F Modular type Blanking Plate :- Supply and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Providing and fixing hexagonal fan box circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

S/F MODULAR BOXES, BASE & COVER PLATE :-Supplying and fixing following size / modules, GI box along with modular base & cover plate for modular switches in recess etc as required 1 or 2 Module (78 mm x 78 mm x 45mm)

S/F MODULAR TYPE SWITCH / SOCKET :- Supplying and fixing following modular switch / socket on the existing modular plate & switch box including connections but excluding modular plate etc as required

Telephone Socket outlet

TV Antenna socket outlet

S/F PVC Conduit Supplying and fixing of following sizes PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required :

Supply and drawing following pair, 0.5 sq.mm. FR PVC insulated copper conductor, unarmoured telephone cable in the existing surface / recessed steel/ PVC conduit as required. 2 Pair

Supply and drawing co-axial TV cable RG-6 grade copper conductor PE insulated,with PVC sheath in the existing surface / recessed PVC conduit as required.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.

1 run of cable

2 run of cable

3 run of cable

S/F T.P MCB DB :-Supplying and fixing following way, three pole and neutral, sheet MCB distribution board 415 volts,on surface /recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, Phosphatized and powder painted including earthing etc. as required (But without MCB / RCCB / Isolators).

6 way (4 + 18), Double door, Horizontal Type

8 way (4 + 24), Double door, Horizontal Type

S/F S.P MCB DB :- Supplying and fixing following way, single pole and neutral, sheet MCB distribution board 240 volts,on surface /recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, Phosphatized and powder painted including earthing etc. as required (But without MCB / RCCB / Isolators).

12 way Double door

S/F 4P MCB Isolator Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required

125 Amps (Incomer for Vertical DB)

S/F SPN (RCCB) Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.

S/F 'C' Series MCB :- Supplying and fixing following 240 volts `C' series, miniature circuit breaker (MCB)suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

6/32 amps, Single Pole

50/63 Amps TPN (Outgoing for Vertical DB)

S/F SP MCB Blanking Plate :- Supplying & fixing single pole, blanking plate in the existing MCB DB complete etc. as required.

S/F VERTICAL TYPE T.P MCB DB :- MAIN BDS Supplying and fixing following way, three pole and neutral, sheet MCB distribution board 415 volts,on surface /recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, Phosphatized and powder painted including earthing etc. as required (But without MCB / RCCB / Isolators).

8 way (4 + 24), Double door,Vertical Type

P/F M.V danger notice Plate Providing and fixing M.V. danger notice plate of 200mmx150mm made of mild steel, atleast 2mm thick and vitreous enamelled white on both sides and with inscription single red colour on front side as required.

SUPPLY OF CEILING & EXHAUST FANS Supply of AC 230/250 volts, 50 HZ ceiling fan with standard down rod, blades, 2 nos. caps & regulator etc. ISI marked complete as required.. 1200 mm sweep (fusion-50 5*)

Supply of AC 230/250 volts, 50 HZ exhaust fans including providing nuts, bolts, mounting frame and other accessories etc. complete . Approved make Exhaust Fan Heavy duty 230V A.C 50 cycles 375 mm 1400 RPM

ERRECTION OF LIGHTING FIXTURES Installation, testing and commissioning of pre-wired, flourescent fitting / compact fluorescent fitting of all types, complete with all accessories and tubes etc. directly on ceiling / wall, including connection with 1.5 sq. mm. FR PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan including wiring the down rod of standard length (upto 30 cm.) with 1.5 sq. mm. FR PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Installaition of Exhaust Fan upto 450 mm, sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning etc as required

EARTHING Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 6 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm Copper. strip on surface or in recess for connections etc. as required.

Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required.

LT CABLE TERMINATIONS & CABLE TRAY Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors,suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

100 mm width X 50 mm depth X 1.6 mm thickness

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 62.5 mm depth X 2 mm thickness

450 mm width X 62.5 mm depth X 2 mm thickness

600 mm width X 75 mm depth X 2 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

100 mm width X 50 mm depth X 1.6 mm thickness

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 62.5 mm depth X 2 mm thickness

450 mm width X 62.5 mm depth X 2 mm thickness

600 mm width X 75 mm depth X 2 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Tee with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

100 mm width X 50 mm depth X 1.6 mm thickness

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 62.5 mm depth X 2 mm thickness

450 mm width X 62.5 mm depth X 2 mm thickness

600 mm width X 75 mm depth X 2 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Reducer with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

100 mm width X 50 mm depth X 1.6 mm thickness

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 62.5 mm depth X 2 mm thickness

450 mm width X 62.5 mm depth X 2 mm thickness

600 mm width X 75 mm depth X 2 mm thickness

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. 100mm dia

NON-SCHEDULE ITEMS

Providing and fixing aluminium die cast body TS 68 door closer with standard arm (EN2/3/4 max door width 1100mm necessary accessories and screws etc complete of approved make

Providing and fixing approved brand and manufacture SS 304 grade Mortice lock with key cylinder 60 mm fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade Tower bolt (TBS 310 S)250mm long with 10mm dia fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade Tower bolt (TBS 36 S) 150mm long with 10mm dia fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 Lever Handle D-type 25mm x 300 (PH2512) mm fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade Door Stopper - door mounted hanging type fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing under mentioned for plain paneling / partitioning with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, making grooves, cutouts for light points etc. complete as per direction of Engineer-incharge (Frame work shall be paid for separately).

12mm thick commercial ply conforming to IS : 1328 BWR type

6mm thick commercial ply conforming to IS: 303 BWR grade

19 mm thick commercial ply board conforming to IS: BWR grade

Providing and fixing plain ceiling for all heights with necessary screws/ nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, making grooves, cutouts for light points complete as per direction of Engineer-incharge (Frame work shall be paid for separately).

12mm thick commercial ply conforming to IS : 1328 BWR type

6mm thick commercial ply conforming to IS: 303 BWR grade

Providing, making and fixing Cupboard in Room of desired size 600mm deep made out of 19mm thick BWR commercial board and 6mm thick ply having lamination of 1mm thick of approved shade and colour with grain direction (to be paid separately) as per drawing on top, bottom, back, sides, vertical partitions, shutters and wherever required as per drawing including making grooves on the elevation and second class teak wood lipping on edges and matching grooves etc., SS hanger rod , SS bracket , box type hinges, magnetic/ ball catchers, Stainless Steel handles in chrome/ brush finish, multi purpose locks, wood preservative paint inlcuding providing and pasting 0.75 mm balancing colour laminate of approved color on unexposed surfaces etc. all as approved and complete as per details shown in design and drawing.

Extra for providing and fixing 50 mm thick polyurethane foam of good quality 50 kg density over wooden paneling including latherite upholstery over and above the foam including staples etc. all complete as per design, drawing

Providing and fixing pelmet of required width made out of 19 mm thick BWR ply board for all heights & levels fiwed to frame work including all scaffolding, screws, nails, cleats, plugs and second class teak wood lipping on edges wood preservative paint etc. all as approved and complete as per details shown in design and drawing.

Extra for Flush sliding door including providing and fixing 6 mm thick mirror over it with steel rollers, channels etc. all complete as per design, drawing.

Providing and fixing 5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets complete fixed with 40 mm long screws, rawl plugs etc., complete

Providing and fixing in position mirror 6mm thick of Modi Guard with 12 mm B.W.P commercial ply at the back and Second class teak wood frame including the cost of screwes, washers, stainless steel studs etc. mirror to be bevelled all complete as per design, drawing and direction of Engineer-in-Charge.

Providing and fixing 100mm x 75mm second class teak wood wood battens over ceiling at different areas as specified fixed to ceiling complete as per design and drawing including all nails, screws, glues and all incidentals to complete the work to the satisfaction of Architect/ Engineer-in-Charge.

Providing & Fixing of Flocked textile floor covering of Nylon 6.6 face fiber or equivalent of approved make with 100% Nylon and completely water proof resilient backing. The flooring should be Anti static with thickness of 4.3 mm and approximate weight of 1.8 k.g./sqm of roll form. The carpet should be completely stain resistant and of a density approx. 80 million fibers/sq.mtr (70 million fiber/sq.yd) in the width of 2 mtr .The floor covering should have Fire Test EN-13501, Appearance Retention Hexapod ISO 140-8, Friction Slip Resistance Test EN 14041 Class DS, SANITISED anti-microbial treatment, with resilient waterproof backing, anti allergic which is certified by British allergy foundation, with ten year replacement guarantee. The carpet should have permanent static control & should be fixed with providing and fixing powder coated aluminum angles as per detail. The work should be carried out by the authorized installer of the Company in India.

Providing and fixng wall paper on walls for all floors & heights finished in smoth line and level etc. all complete (Basic rate Rs. 100 per sqft) of Elementto, Artisan make Product : Fabric Backed Vinyl Wallcovering Total Weight: 450 - 466 grams (15 oz.-20 oz.) per lin. Meter Width : 1.35 - 1.37 meter Backing Woven Cotton Backing Substrate weight: 56 grams per meter Vinyl weight 400 - 410 grams per meter Fire Resistance : Standard: ASTM E- 84 Tunnel Tested, Class - ‘A’ Life safety code NFPA 101 Tensile Breaking Strength : 80X75 Pounds Physical Performance : Standard: QB/T 3805-1999 Color fastness to light: Grade 5 Color fastness to rubbing - Dry rubbing: Grade 5, - Wet rubbing: Grade 5 Wash ability: Extra washable and Durable Tensile load wetness (TD/MD): 111.2/75.6 VOC Test : A+

Providing and fixing of 6mm Thick Exterior Grade High Presure Laminates of timex Bond/ Royal Touch/ Century make Complete fabicacation 63.5mm x 38mm x 1.8 mm thick color anodized aluminum exrruded section do---do-----

Surface Recommendation :- Commercial plain tile/ PCC (the PPC should be firm, curved and flat surface) to be Provied by the client. Specifications GFX floor ( Polished concrete) ( A Cobination of German Engineered Ardex Cements)

Surface Recommendation :- Commercial plain tile/ PCC (the PPC should be firm, curved and flat surface) to be Provied by the client. Specifications GFX floor ( Polished concrete) ( A Cobination of German Engineered Ardex Cements) Printing Area

Providing and fixing of CP brass Health faucet with 8mm dia 1mtr. Long PVC tube and wall hook fixed to wall with rawl plug and CP brass screws complete. (Make: PARRYWARE T9940A1 Slimline with SS Hose & Hook)

Prividing and Fixing 1.5 feet long connecting hose with nuts at both ends complete.(Make: PARRYWARE Cat.No.T991299)

Supplying automatic 'NO-Touch ' SS electric hand-driers complete with all accessories & fittings.(Make:Euronics Model:EH-02)

Providing and fixing capacity of 25 ltr Geyser approved shape including providing & fixing capacity 3 litre/6 litre, including fittings, nuts, bolts and gasket etc complete.

Providing and Fixing 4-way concealed divertor with front plate and diverter handle cutting and making good the wall complete in all respect.

Providing and Fixing Over head shower 100 mm dia with Shower Arm complete as per instructions of the engineer-incharge.

Providing and Fixing CP Bath spout with wall flange complete as per instructions of the engineer-in-charge or as per equivalent make .

Providing and fixing uPVC class-B(IS:13592) trap of self cleaning design complete including cost of cutting and making good the cut-outs in walls and floors etc. complete (P or S trap). 110 mm Outer dia inlet and 110 mm outer dia out let

Providing and fixing 100% stainless steel grating of approved make and quality grade 304 on top of floor trap & Floor drain. The rate includes the cost of all ancillary works and material as required to complete the works.(Make:Chilly) 127mm (Cat No.-SRG-SFCL-127)

Providing and fixing CLEANOUT PLUG for cleaning (Make:Chilly) For 110 OD Pipe (Cat No.-CO-R-128)

Providing & fixing 75mm x 50mm uPVC waste with reducing elbow & nipple cutting chases, the floor / slab, repairs complete as required and connection to pvc waste pipe.

Providing and fixing uPVC HOPPER CONNECTION for 100 mm dia floor trap formed out of main pipe (Type A) with multiple side inlets, suitable for various dia pipes, side connections, including all fixtures and fittings as per site conditions and as per standard details and water tight sealing of joints and area surrounding the grating and as directed.

Supplying all materials, labour, T&P and fitting and fixing Hubless Cast Iron soil, waste, ventilating pipes and required fittings conforming to IS: 1729–2002 or its latest revision to walls with nails, bobbins and wooden plugs or laying in trenches including earthwork in excavation in all kinds of soil and refilling of trenches as per specification and direction of the Engineer in charge. Including required shielded coupling for Hubless centrifugally cast iron pipe

Providing and fixing G.I. (class-C) pipes and fittings conforming to IS: 1239 clamps and hinges including cutting chases and holes and making good the walls and ceiling for waste pipes from wash basins, urinals kitchen sink and equipment waste connections pump deliveries & suction & condensate drainage as directed.

32 mm nominal bore

50 mm nominal bore

Shaver socket unit

RJ 45 socket for Lan cat 6

KEYTAG

BELL PUSH /BUZZER

DND and CMR indicator panel - outside

Supplying, laying, testing and commissioning of following size anealed tinned copper conductor PVC insulated and sheathed copper conductor, unarmoured telephone cable in the existing surface / recessed steel/ PVC conduit with suitable clamps, saddles and including making terminal joints complete as required.

Providing, fixing, connecting & testing of Telephone Tag Block krone type in a suitable size 1.6 mm thick dust and vermin proof Sheet steel enclosure duly painted by synthetic enamel over anti corrosive primer, lockable and hinged cover with provision for cable through glands complete in all respects.

10 pair tag block

30 pair tag block

50 pair tag block

Supplying, erection, testing and commissioning of following tap off / splitter as per specification in 1.6mm thick CRCA sheet steel enclosure for CATV system. 4 Way splitter box

Installation testing commissioning of TPN DBs of 4 way to 12 way including incoming outgoing MCBs,RCCBs,incoming submains wire and outgoing connection & termination of circuits / wires complete in all respects

Installation testing commissioning of SPN DBs of 4 way to 16 way including incoming outgoing MCBs,RCCBs,incoming submains wire and outgoing connection & termination of circuits / wires complete in all respects

SUPPLY OF LIGHTING FIXTURES SUPPLY of following light fixture of approve makes. Supply of LED Tube Light with Batten Suitable for 1X36 Watt LED Tube Light Complete Including tube etc on surface complete in all respect of Havells Cat No LHEXACP7IN1W036 or equivalent

Supply of Surface Mounting Round 18 Watt LED Down Lighter having Powder Coated die cast aluminium housing with heat sink,diffuser/reflector and driver set complete in all respect Havells Cat NoLHEAAHP5IL1W018 or equivalent

Supply of Recess Mounting (300x300) 24/18 Watt LED fitting having Powder Coated die cast aluminium housing with heat sink,diffuser/reflector and driver set complete in all respect Havells Cat No LHEBHEP7IZ1W024 or equivalent

Supply of WALL BRACKET LIGHT Complete Including tube etc on Wall complete in all respect of Havells Cat No LHFOAJD1TZ1T060 or equivalent

Supply of LED MIRROR LIGHT Complete Including tube etc on Wall complete in all respect of Havells Cat No ILHEXASP7PN1W020 or equivalent

Supply installation testing and commissioning of LED COVE LIGHT STRIP Complete of Havells Cat No LHEHCPP7UN1W048 or equivalent.

UPS SYSTEM Supply, installation, testing and commissioning of 10 kVA,3 Phase input and 3 Phase output UPS with isolation transformer alongwith lead acid batteries giving a back up of min. 30min. at full load as per specification alongwith all accessories including interconnecting cables, lugs, Base Frames, Battery Rack & Battery Circuit breaker, palral kit complete as required.Make: 3EM/APC/Autometer

IP BASED CCTV SYSTEM Supply, Installation, Testing and Commissioning of H.265 4MP IR Bullet N/W Camera, 2.8mm, 50M, Micro SD, DC12V/PoE, IP67/IK10, Basic IVA, 4MP resolution (2560 × 1440), True day/night, Digital WDR, 3D DNR, HLC & BLC, Triple streams, Smart codec by ROI, Basic intelligent video analytics, NDAA & Cybersecurity Compliant, CE, FCC, UL, BIS approved, including mounting accessories complete as required & upto the satisfaction of engineer in charge. Sony / American Dynamics / Axis / Pelco / Bosch

Supply, Installation, Testing and Commissioning of 32 Channel NVR , 4 SATA interface, Up to 32 channel Video Inputs, Recording at up to 8 MP resolution, HDMI Video output up to 4K. Supports live view, storage, and playback at up to 8 MP resolution., CE, FCC, UL, BIS approved including all accessories & components for functioning complete as required & upto the satisfaction of engineer in charge. Sony / American Dynamics / Axis / Pelco / Bosch

Supply, Installation, Testing & Commissioning of Special Surveillance 6TB 3.5" SATA HDD internal etc. complete in all respect. Seagate / WD

Supply, installation, testing and commissioning of 42 inch Curved Monitor with 144Hz Refresh Rate, Resolution 1920 x 1080, 1500R Curved Screen, Bezel-less Design including decodes and all accessories complete as required & upto the satisfaction of engineer in charge. LG / Samsung / Sony

Supply, installation, testing and commissioning of System accessories like RJ45 Connectors, Jacks, wireless Mouse, HDMI Cable etc, required to make the system functional complete as required & upto the satisfaction of engineer in charge.

Supply, installation, testing and commissioning of 24 Port Gigabit PoE - smart watchdog function, PoE power up to 30W for each port, 802.3bt 60W Hi PoE standard, PoE IEEE 802.3af/atcompliant PDs, Internal power adapter supply 250W, 250meters Long range PoE Transmit, 8K entry MAC address table with auto-learning and auto-aging, Realtek Switch Chipset+TI PoE Chipset guarantee stable performance complete as required & upto the satisfaction of engineer in charge. Cisco /Binary/Ruckus/Witek

Supply & Installation including termination of unarmoured Cat6- 4 Pair 23 AWG UTP Cable, with cross member pair seperator complete as required in existing coduits. Amp/Molex/Schneider/Siemens/Dlink

VIDEO CONFERENCING SYSTEM Supply, Installation, Testing and Commissioning of Sharp HD video resolutions up to 4k Ultra HD, 4K (2160p) Output, Runs on Android operating system, Built-in Bluetooth for use with Bluetooth speakers/ microphones, keyboards, data exchange, etc., Integrated dual band WiFi to pair with video and web conferencing service, Built-in 4-MIC array with beam-forming, support for external audio equipment and innovative Noise Shield technology, Advanced camera with 16M pixel CMOS sensor, 90 FOV wideangle lens and ePTZ for easy camera view adjustments, Miracast Support for wireless content sharing to share a presentation with conference attendees, Integrated 1x HDMI in, 2x HDMI out, and USB, 1:4 Parties with Licenses, Complete Kit Grandstream / Polycom / Avaya / Cisco

Supply, Installation, Testing and Commissioning of Plate for mounting camera

Supply, Installation, Testing and Commissioning of 65'' LED-backlit LCD flat panel display, DVI, VGA (HD-15). Component, composite, HDMI HDCP compatible direct-lit LED 1080p & 4K (Full HD & 4K Resolution) - Samsung / LG/Sony

Supply, Installation, Testing and Commissioning of Audio-Video specialist cables & connectors

Supply, installation, testing and commissioning of Network Switch - 16 Port PoE complete as required & upto the satisfaction of engineer in charge. Cisco /Netgear /Ruckus/Dlink/Witek

Supply, installation, testing and commissioning of full HD projector, 6000 AL Laser Light. WUXGA Resolution, DLP, 3,000,000 : 1, 16 : 10, Built-in Speaker, for presentation and multimdia usage complete as required & upto the satisfaction of engineer in charge. Sony/JVC/Panasonic/Benq

Supply, installation, testing and commissioning of 120 Inch Motorised Screen, complete as required & upto the satisfaction of engineer in charge. DragonFly / phantom / Tetrabyte / Draper / Grandview

Wiring & accessories for all interconnections as required

CONFERENCE ROOM AUTOMATION WITH PROJECTION SYSTEM Supply, installation, testing and commissioning of Main Control display unit, 10" wall mount Touchscreen, Screen resolution: 1920 × 1200, Dual microphones and larger speakers, Ethernet or Wi-Fi (2.4 GHz + 5 GHz), Camera: 720p or 1080p, Security: WEP, WPA/WPA2 PSK, 802.1x EAP, PEAP, and all accessories complete as required & upto the satisfaction of engineer in charge. Crestron / Control4 / Assa Abloy / Honeywell

Supply, installation, testing & commissioning of main automation controller unit, 4 IR out, control compatibility with android and iOS tablet, smartphone, touch screen, remote, or TV on-screen Navigator complete as required & upto the satisfaction of engineer in charge. Crestron / Control4 / Assa Abloy / Honeywell

Supply, installation, testing and commissioning of Lighting Actuator unit support 8 individual circuits with all related hardware complete as required & upto the satisfaction of engineer in charge. Crestron / Control4 / Assa Abloy / Honeywell

Supply, installation, testing and commissioning of Lighting Dimmer unit support 8 individual circuits with all related hardware complete as required & upto the satisfaction of engineer in charge. Crestron / Control4 / Assa Abloy / Honeywell

Supply, installation, testing and commissioning of Wall Keypad unit for room automation with all related hardware complete as required & upto the satisfaction of engineer in charge. Crestron / Control4 / Assa Abloy / Honeywell

Supply, installation, testing and commissioning of 80 watt ceiling speakers, complete as required & upto the satisfaction of engineer in charge. Episode/Marantz/Sonance

Supply, installation, testing and commissioning of Audio Video Receiver, complete as required & upto the satisfaction of engineer in charge. Episode/Marantz/Sonance/Denon

Supply, installation, testing and commissioning of gateway and Power Supply Unit Crestron / Control4 / Assa Abloy / Honeywell

Wiring & accessories for all interconnections as required

Supply, Installation, Testing and Commissioning of Dual Band Radio High-Performance Wi-Fi unit MU-MIMO technology with following features including all accessories complete as required & upto the satisfaction of engineer in charge: • 4x4 Dual radio 2.53 Gbps performance • 4 stream 802.11AC technology • 2.4GHz bands with speed upto 800 Mbps and 5 Ghz band with speeds upto 1700 Mbps, 500+ users • Indoor 802.11 a/b/g/n/ac long unit • Passive power over internet, Wattage-17W • Long range upto 122 meters depending upon various factors • Beam forming feature • Wall/ ceiling / surface mounted Ruckus / Araknis / Cisco

Supply, installation, testing and commissioning of 24 Port Gigabit PoE smart managed network switch with 24x10/1000BASE-T PoE ports, 4 Gigabit ports with 4 SFP, 24 PoE ports with 193 Watts power nudget, Supports IP interfaces and static routes, IEEE 802.3az energy efficient ethernet, 56 Gbps switching capacity, QoS with Auto Voice VLANs for VoIP complete as required & upto the satisfaction of engineer in charge. Cisco /Netgear/Ruckus/Dlink/Witek

Supply, installation, testing and commissioning of 8 Port Gigabit PoE smart managed network switch with 8x10/1000BASE-T PoE ports, 4 Gigabit ports with 4 SFP, 8 PoE ports with 193 Watts power nudget, Supports IP interfaces and static routes, IEEE 802.3az energy efficient ethernet, 56 Gbps switching capacity, QoS with Auto Voice VLANs for VoIP complete as required & upto the satisfaction of engineer in charge. Cisco /Netgear/Ruckus/Dlink/Witek

Supply, Installation, Testing and Commissioning of accessories like RJ 45 connectors, mounting kits, power injectors etc required to make the system functional upto the satisfaction of engineer in charge. AMP/Molex / Schneider / Dlink

Supply & Installation of CAT 6 UTP jack information outlets complying fully or exceeding with category 6 connecting hardware specifications for all pair combinations up to 250 MHz. Outlets shall use lead frame technology, non PCB pyramid type. Complete as required and as per technical specifications. (Wi-fi access point) AMP/Molex / Schneider / Dlink

Supply & Installation of CAT 6 UTP jack information outlets complying fully or exceeding with category 6 connecting hardware specifications for all pair combinations up to 250 MHz. Outlets shall use lead frame technology, non PCB pyramid type. Complete as required and as per technical specifications. (Data Outlets) AMP/Molex / Schneider / Dlink

Supply & Installation of CAT 6 UTP jack information outlets complying fully or exceeding with category 6 connecting hardware specifications for all pair combinations up to 250 MHz. Outlets shall use lead frame technology, non PCB pyramid type. Complete as required and as per technical specifications. (Telephone Outlets) AMP/Molex / Schneider / Dlink

Supply & Installation of Single Face Plates along with clearly printed labels and holders complete as required and as per technical specifications. AMP/Molex / Schneider / Dlink

Supply & Installation of Cat6- 4 Pair 23 AWG UTP Cable with cross member pair seperator in existing concealed/exposed raceway/conduit, complete as required and as per technical specifications. AMP/Molex / Schneider / Dlink

Supplying and fixing in position 0.8mm thick GI box for data/voice outlet suitable for fixing of RJ 45 jack complete as required.

Supplying and fixing in position PVC back box for data/voice outlet complete as required.

IP IPABX SYSTEM - TELEPHONY Supply, installation, testing and commissioning of Super Hybrid PBX Equipped with '- 03 Trunk Lines, 50 Extensions, Expandable to 8 Trunks & 100 Extensions, with built in Auto Attendant, with Built in Caller ID Card for 3 Trunks. NEC Japan / Epygy USA / Grandstream USA

Supply, installation, testing and commissioning of Key Telephone, Single Line LCD Display with 12 Programmable Keys NEC Japan / Epygy USA / Grandstream USA

DTF Card for 16 Analog Extensions NEC Japan / Epygy USA / Grandstream USA

MDF (Krone) & Connecting Cable (3 x 16) NEC Japan / Epygy USA / Grandstream USA

LED TV Sony Smart Television Tv 55 Inch 4K Ultra HD SonyR (KD-55X80J) Product id: 5116877-36419788158 Country Of Origin: India

Supplying and placing of King Size bed Size. (L)2017mm X(W)1574mmX(H)1200mm.Material Engieered wood. The Product should be fom GREEN GUARD, AIOTA, IGVC, FSC Certified.Make Durian , Model No CM LILLIAN, Warranty 5 Years or Equivalent

Supply and Installation of Bedside Table. Size (L)500mm X (D)400mm X (H)450mm. The bed side unit is made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The bed side table has one drawer and one shelf. The shelf is made of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The product must be from a Manufacturer having ISO 9001,ISO 14001 ,ROHS ,Indian Design Mark ,Latest BIFMA and IGBC certificates for few of its products.Make-Durian,Model No ROBINSON/NT, Warranty-5 Years or Equivalent

Supplying and placing of Center Table Material & Subtype Marble Size.(L)1200mm X (D)600mm X (H)480mm.Finish Glossy The Product should be fom GREEN GUARD, AIOTA, IGVC, FSC Certified.Make Durian , Model No CATHRINE , Warranty 5 Years or Equivalent

Supplying and placing of Park 2 Seater sofa Size. (L)1410mm X (D)890mm X (H)870mm. Material Fabric.The Product should be fom GREEN GUARD, AIOTA, IGVC, FSC Certified.Make Durian , Model No PARK, Warranty 5 Years

Supplying and placing of JORDON Chair Size. (W)610mmX(D)470mmX(H)1040.The Product should be fom GREEN GUARD, AIOTA, IGVC, FSC Certified.Make Durian , Model No MMPL/70024/MB, Warranty 5 Years or Equivalent

Supplying and placing of Study TableWith Glass.top & Metal Leg.Size(L) 4'3"X(D)2'X(H)2'5" The Product should be fom GREEN GUARD, AIOTA, IGVC, FSC Certified.Make Durian , Model No CM-MONROE Warranty 5 Years or Equivalent

Supplying and placing of Study TableWith Glass.top & Metal Leg.Size(L) 6'X(D)2'X(H)2'5" The Product should be fom GREEN GUARD, AIOTA, IGVC, FSC Certified.Make Durian , Model No CM-MONROE Warranty 5 Years or Equivalent

Supplying and placing of TV Unit Size. (L)10'X (D)1'4"X (H)2'5". The table top made in 25mm thk pre lame particle board with PVC banding,The Product should be fom GREEN GUARD, AIOTA, IGVC, FSC Certified.Make Durian , Model No DWS/TV/CM, Warranty 5 Years or Equivalent

Supplying and placing of Park 3 Seater sofa Size. (L) 1905mm X (D) 890mm X (H) 870mm Material Fabric.The Product should be fom GREEN GUARD, AIOTA, IGVC, FSC Certified.Make Durian , Model No PARK, Warranty 5 Years or Equivalent

Supplying and placing of Park 1 Seater sofa Size. (L)960mm X (D)890mm X (H)870mm Material Fabric.The Product should be fom GREEN GUARD, AIOTA, IGVC, FSC Certified.Make Durian , Model No PARK, Warranty 5 Years or Equivalent

Supplying and placing of side table Size. (L)960mm X (D)890mm X (H)870mm Material Fabric.The Product should be fom GREEN GUARD, AIOTA, IGVC, FSC Certified.Make Durian , Model No hopper/st, Warranty 5 Years or Equivalent

Supplying and placing of four seater round dining table with wooden frame along with four dining chair model no-Caspian+Esmira Material & Subtype Marble Size.(L) X (D)600mm X (H)480mm.Finish Glossy The Product should be fom GREEN GUARD, AIOTA, IGVC, FSC Certified.Make Durian , Model No-Caspian+Esmira , or Equivalent

Supplying and placing of Confrece table 26 seater the table top made 30 mm thk MDF Board teek wood finish vineer top model no- DWS/CM/ROLTA Material & Subtype Marble Finish Glossy The Product should be fom GREEN GUARD, AIOTA, IGVC, FSC Certified.Make Durian , or Equivalent

Supplying and placing of High Back Chair For Confrence, the Alpha is a leader standing tall in this High Back variant with a chrome vaulted base and sleek chrome armrests. The chair boasts of a padded headrest along with the back, cushions and armrest panels are upholstered in Burgundy Leather for a premium look and feel. Product Dimension : (W)650mm X (D)480mm X (H)1300mm Model No RICH/37815/HB The Product should be fom GREEN GUARD, AIOTA, IGVC, FSC Certified.Make Durian , or Equivalent

Supplying and placing of High Back Chair For Confrence, the Alpha is a leader standing tall in this High Back variant with a chrome vaulted base and sleek chrome armrests. The chair boasts of a padded headrest along with the back, cushions and armrest panels are upholstered in Burgundy Leather for a premium look and feel. Product Dimension : (W)650mm X (D)510mm X (H)1150mm model no-Alpha/hb The Product should be fom GREEN GUARD, AIOTA, IGVC, FSC Certified.Make Durian , or Equivalent

Supplying and placing of cafetaria table four seater with four chair the table is made of wooden frame and glass top Model No- Tasman+Amelia or Equivalent

Supplying and placing of Reception Table Reception table size: 2400L x 1050D x 750Ht/1050Ht. Table top made of 25mm thk. Prelam Particle baord with PVC Edge banding. Table top supported on MS Legs and Perforated Modesty Panel. Provision of Counter Glass top or Equivalent

Providing, Supplying and fixing Curtain Fabric of following specifications Product Code: CAR0014. Composition: 100% Polyester. Width: 1.385 meter. Martindale: 65000.GSM: 310. or Equivalent

Providing, Supplying and fixing Sheer Fabric of following specifications Product Code: MOR0027. Composition: 100% Polyester. Width: 1.39 meter. Martindale: N/A. GSM: 116.or Equivalent

Providing, Supplying and laying Matress of following specifications Product Name: Esteem Assured Warranty*: 5 years. Features: · Medium Firm Pocket Spring · Impression Memory Foam in Top Quilting · Soft High Resilience Layer for Comfort · Engineered Side Wall · Premium Knitted Fabric · Zero Turn Technology · Zero Partner Disturbance or Equivalent

Providing, Supplying and laying Comforter Size: Double Bed. GSM: 300.or Equivalent

Providing and fixing Track – Super Track of following specifications Make: Vista or Equivalent

Voltas make Inverter Split Air Conditioner (5 Star ISEER)-100%- Copper) 1.5 TR HSN/SAC Code-8415 or Equivalent

Voltas Make Automatic Voltage Stabilizer 4KVA HSN/SAC Code-9032

Refrigerant Copper Pipe HSN/SAC Code-7411

Bracket Angle for Outdoor Unit HSN/SAC Code-7301

Installation Charge of Air Conditioner HSN/SAC Code-995469

STORE SECTION.

SS Storage Rack - 4 shelf. Make Jonree and Equivalent

SS Potato Onion Bins Make Jonree and Equivalent

SS Pallet Make Jonree and Equivalent

SS Platform trolley with pusshing handle.Make Jonree and Equivalent

Vegitable washing Machine : 100 Kgs /Hr. Make Jonree and Equivalent

Weighing Scale - Capacity 300 Kgs.CAS Make

Weighing Scale - Capacity 50 Kgs.CAS Make

Insect Killer - 2 Tube SPECTRUM Make

Air Curtain: Aerotek - 1.5 MtrLenght

SS 4 Door Vertical Refrigerator : Cap-900 mLtrs . Tem range : 0c to 8 C Make Jonree and Equivalent

SS 4 Door Vertical Deep Freezer : Cap-900 mLtrs . Tem Range : -18C to -15C Make Jonree and Equivalent

Glass door Ice Cream freezer - Voltas make : capacity 205 Ltrs Make Jonree and Equivalent

CUTTING & PREPARATION AREA Make Jonree and Equivalent

SS Potato Peeler : Capacity 10 Kg Make Jonree and Equivalent

SS Wet Masala Grinder : Capacity 7 Ltrs Make Jonree and Equivalent

SS Dough Kneading Machine : Capacity- 7 kgs Make Jonree and Equivalent

Pulvarisor : 2 HP Motor Capacity Make Jonree and Equivalent

Vegetable cutting Machine with 6 Disc Make Jonree and Equivalent

Meat Mincer Make Jonree and Equivalent

Meat Slicer.Make Jonree and Equivalent

SS working table with sink and water outlet valve.Make Jonree and Equivalent

SS Cutting Table with one Bottom shlef.Make Jonree and Equivalent

Hose Real for floor washing Make &Model T & S or equivalent.

Insect Killer - 2 Tube SPECTRUM Make Make Jonree and Equivalent

Chopping Block Make Jonree and Equivalent

SS Copping Board Streiliser Sink.Make Jonree and Equivalent

SS Knife Streliser Sink Make Jonree and Equivalent

SS Kitchen Utily Trolley.Make Jonree and Equivalent

MAIN KITCHEN INDIAN AND TANDOOR SECTION.

SS 2 Burner Indian Cooking Range with all gas burner fittings and controls.Make Jonree and Equivalent

Single Sink Unit with CI water outlet Valve.Make Jonree and Equivalent

Spreador Table for indian burner

SS 3 door worktop Chiller Cap- 470 Ltrs . Temp Range : 0C to +10C. With overhead heating warmer, Make Jonree and Equivalent

SS Coal Tandoor

SS Support Table for Tandoor with BS Make Jonree and Equivalent

Single Sink Unit with CI water outlet Valve. Make Jonree and Equivalent

SS 2 door worktop Chiller Cap- 470 Ltrs . Temp Range : 0C to +10C. With overhead heating warmer, Make Jonree and Equivalent

SS Chapati Plate with puffer and all gas burner fittins Make Jonree and Equivalent

Chapati rolling table with one BS Make Jonree and Equivalent

Chapati Collection Table with one BS Make Jonree and Equivalent

BULK KITCHEN Make Jonree and Equivalent

SS Tilting Boiling Pan : Capacity - 80 Ltrs.Gas operated.Make Jonree and Equivalent

SS Tilting Brat Pan : Capacity - 80 Ltrs.Gas operated.Make Jonree and Equivalent

SS pickup table with 1 BS and 2 Over head shelf.Make Jonree and Equivalent

SS 4 Door Vertical Refrigerator : Cap-900 mLtrs . Tem range : 0c to 8 C Make Jonree and Equivalent

CHINESE SECTION

SS 3 Burner Chinese cooking range with 2 stock pot and gas burner fittings Make Jonree and Equivalent

Dimsum/Momo Streamer. Make Jonree and Equivalent

SS chinese support table with 2 BS Make Jonree and Equivalent

SS Masala Troleey Make Jonree and Equivalent

SS 3 door worktop Chiller Cap- 470 Ltrs . Temp Range : 0C to +10C. With overhead heating warmer, Make Jonree and Equivalent

CONTI SECTION

2 Burner Range with below oven with heater.Gas and below heatre.Make Jonree and Equivalent

SS Deep fat fryer double capcity (6+6)=12 ltrs Make Jonree and Equivalent

Gas Griddle plate 1/2 grooved and 1/2 flat. On stand.Make Jonree and Equivalent

Electric salamander : static. Wall mounted , with MS angle Frame.Make Jonree and Equivalent

SS support table with one BS Make Jonree and Equivalent

SS working table with sink and water outlet valve.Make Jonree and Equivalent

3 Door work top chiller with GN Pan ( Salad Counter). With Overhead heating arrangement

SNACKS AND BEVERAGE SECTION Make Jonree and Equivalent

SS Dhosa Hot plate with all gas burner fittings and controls

SS iddly steamer : Capacity 54 Iddly with stand.

SS Single Burner Range with gas burner fittings.

SS Dhosa Mis-en Pla Table with 5 vessels.

Bain Marie with 4 nos 1/2 GN pan with electrical heater.

Service pickup table with heating arrangement

PANTRY SECTION Make Jonree and Equivalent

Piza Oven : Electric Double Chamber.

Sandwith Griller Double

Gas Griddle plate 1/2 grooved and 1/2 flat. On stand.

SS Deep fat fryer double capcity (6+6)=12 ltrs

3 Door work top chiller with GN Pan ( Salad Counter). With Overhead heating arrangement

SS work table with 2 Bottom shelf

SS working table with sink and water outlet valve.

HOT & COLD BEVERAGE Make Jonree and Equivalent

Glass door Ice Cream freezer - Voltas make : capacity 205 Ltrs

Commercial Blender : Capacity 2 Ltrs Make HTC

JUCER-Centrifugal Juicer

Ice-Cube Machine with Self Contain Bin - JE-45Capacity -45 Kgs/24 Hr.Storage Capacity : 13 Kgs. Condensing : Air Cooled Power : 0.36KW, 220V

Double Group Coffee MachineCapacity : 10.5 Ltrs. Power : 3 kw, 220V. MAKE -MAJISTER- Italy.

Coffee GrinderCapacity : 0.5 Kgs. Size : 270 x 375 x 165 Power : 0.14 Kw, 220V Make : CUNIL- Spain.

SS working table with sink and water outlet valve.

2 door Under Counter Bain Marie with 6pcs pan 1/2 StaticCapacity : 6 x 1/2 GN Pan Power : 2 kw, 220V

3 Door Back Bar ChillerCapacity : 338 Litrs Size. (mm) : 1335 x 505 x 875 Led Light Inside Temp. : +2oC ~ +8oC Power : 0.25 kw, 220V

SERVICE STATION.Make Jonree and Equivalent

SS Service Pickup counter with over head shelf & front cutlery crockery cabinet.

3 Door work top chiller with GN Pan ( Salad Counter). With Overhead heating arrangement

GUEST DIANING AREA.Make Jonree and Equivalent

Induction Cooker with cheffing dish(Buffet Induction Plate, Make Stella)340 X 340 X 94 and Chefing Dish with Glass Lid for Induction Hot Plate.Capacity : 6.8 Ltrs. Dia : 360mm

2 door Under Counter Bain Marie with 6pcs pan 1/2 StaticCapacity : 6 x 1/2 GN Pan Power : 2 kw, 220V

Juice Dispenser Make Jonree and Equivalent

SS Tea, Coffee and Milk dispenser with electrical fittings

Soup Kettle - MS Body Size : 340 x 340 x 395 Capacity : 10 Ltrs.

PLATE WASH SECTION Make Jonree and Equivalent

SS Soiled dish landing table with garbagechute and Overhead Glass Rack.

SS 2 sink washing unit with CI Outlet Valve.

Prerinse Unit

Hood Type Dishwashing Machine. Imported -WALO- Italy , load 8.6, 440.V

SS Clean Dish Glass Rack - 4 Shelves.

SS Pot Rack - 4 shelf

MANIFOLD AND LPGAS PIPELINE Make Jonree and Equivalent

15X2=30 Cylinder Manifold system with all necessary fittings .TATA C Class pipe line 1" dia pipeline approx 150 feet with all necessary fittings , fixing, painting and testing

HOT AIR AND FRESH AIR VENTILATION SYSTEM Make Jonree and Equivalent

SS Hood with filter 14 nos

Centrifugal faan : with 5 HP Motor ( As per site Position)

Axial flw fan with 2 HP Motor ( Asper site position)

GI Ductline with fittings and fixing : approx 300 sft.( As per site Position )

DRAIN THROUGH GRAITINGS Make Jonree and Equivalent

SS Floor Drain Graings for All Section

Precor TRM 731 Treadmill - Built for high-use on our commercial platform,this treadmill sacrifices nothing in longevity, making it a money-saving valuable investment. Features like the Active Status Light™ make it easy to maintain for any of your staff and decreases product downtime. Large Advanced LED Display (P31 Console); 27 Workouts; Commerical 4HP AC Motor; Integrated Footplant Technology™; Ground Effects® Impact Control System; Running Surface 60" x 22"; Step Up Height: 9,5"; Speed Range: 0.8-19.2 km/h; Elevation Range: 0%- 15% (0.5% inc); User Wt - 181kg; Machine Wt - 184kg; Dimension (LxWxH) - 83" x 35" x 62" and Equivalent

Precor EFX 731 Elliptical Fitness Crosstrainer - The EFX® 731 combines reliability with the basics done right approach to give you the perfect elliptical. The EFX is easy to clean and maintain, including the convenience Large Advanced LED Display (P31 Console); 15 Workouts; Resistance Levels: 20; Ramp Angle: 20° Fixed; Stride Length: 21" User Weight - 159kg; Machine Weight - 126kg; Dimension (LxWxH) - 80" x 28" x 67" and Equivalent

Precor Experience Series RBK 635 Recumbent Bike - It features the P30 console and a step-through design to appeal to a wide range of exercisers. The simple seat adjustment allows the user to change the position of the seat with one hand, either on or off the bike. A ventilated Airflex seat provides exceptional comfort.; Large LED Display (P30 Console); 12 Workouts; Dual-sided pedals allow the user to use it with or without the integrated straps; Resistance Levels: 25; Self Powered; User Weight - 159kg; Machine Weight - 81kg; Dimension (LxWxH) - 65" x 23" x 51" and Equivalent

Crux SS 118 Four Station Multi-Gym Main Function：Chest Press, Pec Fly, Squatting, Parallel Bars, Hanging Legs, Seated Rowing, Lat Pull Down, Leg Curl, etc.1. Main Tube: 100*50Circular Tube 3. Steel Cable is Imported From Japan: High Flexibility, Self-Lubricating, and Wear-Resistant Coating, Cold Resistance, Capacity 1400KGTwo Weigh Group Plates:156KGS(66+90kg)Dimension: 2550*2450*2080mm of the Active Status Light™ - all to improve your ownership experience. 2. Antistatic and Antirust Spraying and Equivalent

Passenger Lift (G+2) Design Manufacture, Supplying delivery at site, Installation, Testing & Commissioning of Machine Less/ Gearless Elevator (Regenerating Type) in following Shaft following dimensions and for minimum payload carrying capacity of passenger serving different floors as per specifications and as per CPWD specification as under:-

Shaft of dimensions 2000mm x 1700 mm (W x D)

Capacity of 8 passenger/ 544 kg

Speed:1.0 meter per second (MPS)

Floor: (G+2)

Travel: 9.0 (Approx.)

Stops & Opening: 3

Automatic rescue device complete with dry maintenance free batteries as required.

Controller: A.C. Variable Voltage Variable Frequency (ACVVVF)

Power: 400/415 Volts (3 Phase AC)

Type of doors:

Car: Power operated, centre opening horizontal sliding Stainless Steel Hairline finish, Linen Cladding with artwork on wall. Car size - 2000 wide x 1100 deep x 2700 high.

Ceiling : Aluminium/ Alloy + Acrylic finish.

Landing doors: 900 wide and 2400 high C/O Stainless Steel Hairline finish.

A flat handrail dia 50mm stainless steel 304 Grade hollow tubular of suitable length as per Lift Car dimension but not less than 800mm long at 900mm above floor level to be fixed on rear wall of the lift car.

Voice announcement system in the car to announce the position of the elevator in the hoist way as the car passes or stops at a floor served by the elevators.

Braille signage/ button both inside and outside of car.

Fire man switch

Automatic self landing feature to bring elevator CAR with in 0 to + 3mm of landing floor regard less of load and direction of Travel.

Flooring: 18-20mm recess for Natural Granite/ Marble Stone flooring.

Fans and Light motion sensor based to confirm to Griha 3 norms.

Add 12% GST

Add 1% Labour Cess

R P Singh & Co.