PLENARY E/M REPAIR WORK OF OFFICERS, JCOS ORS MD ACCN AT NEW CANTT PRAYAGRAJ

Amount

Taking down carefully point wiring of any type complete for light, fan socket or power point with fittings & fixtures such as ceiling rose, electric fittings, holders, switches, sockets, regulators, wooden batten, surface conduit/casing caping/conceal etc. removing materials including accessories for taking credit and making good disturbed surface to match the existing complete all as specified & directed.

M&L for point wiring with FRLS PVC insulated unsheathed stranded copper conductor cable 1.5 Sqmm (nominal area) 1100 volts grade, along with one single run of same size and type of copper wire as continuous earth wire to common earth dolly drawn in and including non metallic PVC rigid, medium grade concealed conduit with all fixing accessories of 20mm dia, using new MS sunk terminal boxes of thickness not less 1.2mm, new 3mm thick laminated sheet cover with brass screw and cup washers with all accessories and making good to disturbed conceal surfaces complete all as specified and directed for the following :- Note:(a) Colour code of wire shall be strictly followed , Red for Phase , Black for neutral and green for earth wire (b) The unit rate quoted is deemed to be inclusive of cost of cutting chases in wall for providing concealed conduit and making good to match with existing finish/surface.

One light/fan/bell point controlled by one switch

One point for socket outlet 5 amps on independent board

One point for socket outlet 5 amp same board

One light point controlled by two 2 - way switch

All as per Srl item No. 2 above but fot one 3 pin socket outlet 15 amps, independent, with cables 2.5 sq. mm size on independent board with 2.5 Sqmm earth wire.

All as per Srl item No. 2 above but fot one 3 pin socket outlet 15 amps, independent, with cables 4 sq. mm size on independent board with 4 Sqmm earth wire.

M&L for point wiring with FRLS PVC insulated unsheathed stranded copper conductor cable 1.5 Sqmm (nominal area) 1100 volts grade, along with one single run of same size and type of copper wire as continuous earth wire to common earth dolly drawn in and including non metallic PVC rigid, medium grade not less than 20mm dia surface conduit / non metallic PVC casing and caping not less than 20mm wide med grade ISI marked with all fixing accessories , using new MS sunk terminal boxes of thickness not less 1.2mm, new 3mm thick laminated sheet cover with brass screw and cup washers with all accessories and making good to disturbed surfaces complete for one light/fan/bell point / 5 Amp independent socket point controlled by one switch all as specified and directed :- Note:(a) Colour code of wire shall be strictly followed , Red for Phase , Black for neutral and green for earth wire

All as per Srl item No. 3 above but fot one 3 pin socket outlet 15 amps, independent, with cables 4 sq. mm size on independent board with 4 Sqmm earth wire.

M&L for point wiring with FRLS PVC insulated unsheathed stranded copper conductor cable 1.5 Sqmm (nominal area) 1100 volts grade, along with one single run of same size and type of copper wire as continuous earth wire to common earth dolly drawn in existing conduit of PVC rigid, medium grade with all fixing accessories , using new MS sunk terminal boxes of thickness not less 1.2mm, new 3mm thick laminated sheet cover with brass screw and cup washers with all accessories and making good to disturbed surfaces complete for one light/fan/bell point / 5 Amp independent socket point controlled by one switch all as specified and directed :- Note:(a) Colour code of wire shall be strictly followed , Red for Phase , Black for neutral and green for earth wire

M&L in replacement for concealed submain wiring using FRLS PVC insulated, unsheathed stranded copper conductor cable two single core of following sizes of voltage rating upto and including 1100 volts drawn in and including PVC concealed conduit of dia not less than 20 mm dia with all fittings and accessories alongwith one run of PVC insulated unsheathed stranded copper conductor of size 1.5 Sqmm as earth continuity conductor complete all as specified & directed. Note:- (i) Two runs of single core PVC cable with one run of earth conductor and conduit shall be measured as one length. (ii) The cost for cutting, chases required shall deemed to be included in the quoted unit rate.

2 run of 4 Sqmm & one run of 4 Sqmm as earth wire

2 run of 6 Sqmm & one run of 6 Sqmm as earth wire

2 run of 10 Sqmm & one run of 10 Sqmm as earth wire

4 run of 10 Sqmm & one run of 10 Sqmm as earth wire

M&L in replacement for concealed submain wiring using FRLS PVC insulated, unsheathed stranded copper conductor cable two single core of following sizes of voltage rating upto and including 1100 volts drawn in and including non metallic PVC rigid, medium grade not less than 20mm dia surface conduit / non metallic PVC casing and caping with all fittings and accessories alongwith one run of PVC insulated unsheathed stranded copper conductor of size 1.5 Sqmm as earth continuity conductor complete all as specified & directed. Note:- (i) Two runs of single core PVC cable with one run of earth conductor and conduit shall be measured as one length. (ii) The cost for cutting, chases required shall deemed to be included in the quoted unit rate.

2 run of 4 Sqmm & one run of 4 Sqmm as earth wire

2 run of 6 Sqmm & one run of 6 Sqmm as earth wire

M&L in replacement for concealed submain wiring using FRLS PVC insulated, unsheathed stranded copper conductor cable two single core of following sizes of voltage rating upto and including 1100 volts drawn in existing conduit of PVC rigid, medium grade with all fittings and accessories alongwith one run of PVC insulated unsheathed stranded copper conductor of size 1.5 Sqmm as earth continuity conductor complete all as specified & directed. Note:- (i) Two runs of single core PVC cable with one run of earth conductor and conduit shall be measured as one length. (ii) The cost for cutting, chases required shall deemed to be included in the quoted unit rate.

2 run of 4 Sqmm & one run of 4 Sqmm as earth wire

2 run of 6 Sqmm & one run of 6 Sqmm as earth wire

Receiving complaints from Concern In charge of Internal section (Power House) lodged by the occupants of electrification nature, rectification of the fault as per the complaint lodged by the user onward KWH meter in respect of main distribution board having switch fused, MCB distribution board in sheet metal enclosure, point wiring fixture for light/fan/bell/light/Ceiling Fan, testing of Electronic meters or power socket complete repairs to the extent by removing connections from the system removing faults in wires, battens, conduit, sunken boxes, junction boxes, main switches, MCBs/DBs utility light fitting, lamp holders AC ceiling/exhaust fans and other connected fixtures of the internal electrification including providing of petty stores such as wires of appropriate size and conductor matching to existing one up to the length of 1 mtr including insulation tap, screws, nuts as required to rectified the fault with regard to the complaint lodged and refixing of fittings, fixture to their position as dismantled complete all as directed at site to the entire satisfaction of Engr-in-charge/users. Note - (i) All spares required i.e. tube light any type, Choke any type, CFL,LED, starter, bipin holder, starter holder etc accessories, required for repairing will be paid under relevant supply only items of this schedule. Instructions -(a) Attending complaint including taking down/refixing of LED light fittings and repair/ Replacement part (Labour ) and minor repair shall be measured against Srl item No 1 of Sch "A" (b) Cost of material and labour for replacement of new items shall be measured and paid separately under relevent items of sch "A" against supply only here-in-after (Item No 10 to 39) (c) Panalty : Penalty for not attending complaints within stipulated time frame will be the liable to Rs 500.00 of per day for non attending the complaints multiple number of days of delay (d) Priority -1 (to be done within 8 hours from time of lodging complaint): No light, repair/replacement of switches, fan regulator, replacing burnt/damaged wiring, replacement of burnt MCBS and Main switch, voltage fluctuation, current leakage and replacement of tube lights.

Supply only in replacement of switch piano flush button type 5 amps single pole one way complete all as specified & directed

Supply only in replacement of switch piano flush button type 15 amps single pole one way complete all as specified & directed.

Supply only in replacement of socket outlet multipurpose 2/3 pin 5 amps flush button complete all as specified & directed.

Supply only in replacement of socket outlet multipurpose 2 in 1, 5 and 15 Amps complete all as specified & directed.

Supply only in replacement of 15 Amps switch socket combination 240V complete all as specified & directed

Supply only in replacement of ceiling fan regulator step type 240 Volt AC complete all as specified & directed

Supply only in replacement bell push flush type 5 amps complete all as specified and directed.

Supply only in replacement ceiling rose surface type complete all as specified and directed.

Supply only in replacement angle/batten type lamp holder, PVC/Polycarbonate type with back plate complete all as specified & directed.

Supply only in replacement of call bell, ding dong type, AC, 230 V, single pole complete all as specified & directed.

Supply only in replacement Modular single pole and neutral enclosure with a two pin earth plug and socket complete with one single pole MCB 20/25 Amps "B" Curve. Complete all as specified and directed.

Supply only in replacement of modular switch 1 way, 5/6 amps, 230V AC, one way complete all as specified & directed.

Supply only in replacement of modular socket out let 2-in-1, 3 pin, 5/6 amp flush type 2 module complete all as specified & directed.

Supply only in replacement of modular switch flush type 15/16 amps, 230V AC single pole two way complete all as specified & directed.

Supply only in replacement of modular socket out let 2-in-1, 3 pin, 5 & 16 amp flush type 2 module complete all as specified & directed.

Supply only in replacement of modular fan regulator, 5 stepped, electronic type, single phase, 120 watt, 1/2 module including connection complete all as specified & directed.

Supply only in replacement of modular metal flush box of 12 module complete all as specified and directed.

Supply only in replacement of modular metal flush box of 8 module complete all as specified and directed.

Supply only in replacement of modular metal flush box of 6 module complete all as specified and directed.

Supply only in replacement of modular metal flush box of 3/4 module complete all as specified and directed.

Supply only in replacement of modular metal flush box of 2 module complete all as specified and directed.

Supply only in replacement of modular white plate cover with frame of 12module complete all as specified and directed.

Supply only in replacement of modular white plate cover with frame of 8 module complete all as specified and directed.

Supply only in replacement of modular white plate cover with frame of 6 module complete all as specified and directed.

Supply only in replacement of modular white plate cover with frame of 3/4 module complete all as specified and directed.

Supply only in replacement of modular white plate cover with frame of 1/2 module complete all as specified and directed.

Supply only in replacement of modular bell push flush type 6 amp, 1 module SP , 230V AC complete all as specified & directed.

Supply only in replacement of PVC insulation tape of width - 18 mm, thickness - 0.125 mm in length of 25 mtr ISI marked for proper insulation of joints in wire where as required or directed.

Supply only in replacement of condenser of 3.15 MFD, 240 Volt AC , conforming to IS - 1709 suitable for fans complete all as specified and directed.

Supply only in replacement of condenser of 2.5 MFD, 240 Volt AC , conforming to IS - 1709 suitable for fans complete all as specified and directed.

S&F in repair fan hook suitable for 40 mm dia pipe, made out of MS flat iron size 50x6 mm including suitable size of nut, bolt & washer complete all as specified and directed.

Supply and fixing in replacement of ventilation fans PVC body of size 250 mm sweep including taking down the old unserviceable one and depositing the same in MES yard for further disposal as per existing procedure complete all as specified & directed.

M&L for dismantling of ceiling fans AC single phase 230 volts of sizes 1200mm/1400mm (collected from MES fan store) any make / model , dismantled its stator, rotor, cutting out burnt copper winding and providing new winding with super enamelled copper winding wire existing size including cleaning of slots providing oil impregnated insulation paper or minimax, fibre, insulation in slots and well wraping with cotton tape, bind with cotton thread and varnishing over all with winding varnish as approved by Engineer - in - charge cleaning of bearing housing and shaft, replacing spares such as split pins, blade screws etc as required and deposited to MES store after testing complete all as specified and directed. Note - (i) Fans to be collected by the contractor at their own arrangement from AGE E/M store for repair/rewinding and to be deposited at same place after making serviceable duly tested. (ii) Spare parts as required to make the serviceable of same is deemed in quoted rate.

All as per Srl item No. 42 above but for Exhaust Fan of sweep Size 300/380mm , AC ,single phase 230/240 volts complete all as specified & directed.

Supply and fixing fan blade suitable for 1200mm sweep ceiling fan complete similar to original make with new screws complete all as specified and directed.

Supply and fixing outer body with stator and rotor complete with down rod, clamps, rubber reel, nut bolts etc & all accessories duly painted suitable for 1200 mm sweep ceiling fans complete all as specified and directed.

Supply and fixing Exhaust fan blade duly painted suitable for 300 mm/380mm sweep complete all as specified and directed.

Supply and fixing outer frame complete with stator,rotor,clamps, rubber packing, nut bolts etc & all accessories duly painted suitable for 300 mm /380 mm sweep exhaust fans complete all as specified and directed.

Supply and fixing in replacement of 15 W LED down lighter Ultra slim decorative aluminium casted recess mounted round fixture in white finish with opal diffuser and separate electronic driver ,suitable for low depth ceiling complete all as specified and directed. Make:- Philips Model No.Green perform dusk or equivalent make as specified in P.S

Supply and fixing in replacement of slim, compact, aluminum die cast edge lit panel. surface mounted square fixture and separate electronic driver with high brightness LEDs with diffuser to give glare free light of 26 W complete all as specified and directed. Make Philips model No. sleek surface or equivalent make as specified in P.S

Supply and fixing in replacement of recess mounted round down lighter Al pressure die –cast heat sink with high brightness LEDs with diffuser to give glare free light of 15 W LED 6500 K complete all as directed by Engi-in-Charge. Make Philips Model No. Green Perform sleek G2 or equivalent make as specified in P.S

Supply and fixing in replacement of wall bracket Decorative, wall mounting, Shiny stainless steel base & glass opal paint finish including 20 wall LED bulb fixture With bulb base B22 complete all as specified & directed .Make Philips model No.sense of style double head wall light or equivalent make as specified in P.S

Supply and fixing in replacement of dual wall bracket Decorative, wall mounting, metal and chrome & glass opal paint finish including 2X10 wall LED bulb fixture With bulb base E32 complete all as specified & directed. Make Philips model No. Glint Single Head wall light or equivalent make as specified in P.S

Supply and fixing in replacement of 36 W LED, 2'x2' Panel Ultra slim recess mounted LED module with high brightness LED package and unique pattern de-glaring PP diffuser and PS LGP de-glaring diffuser sheet for glare free uniform light distribution suitable for armstrong / grid ceiling applications complete all as specified and directed. Make Philips Full glow Cat No. RC380B LED36S-6500G6 L60W60PSU ODS1 or equivalent make as specified in P.S

Supply and fixing in replacement of 40 /42 W LED, 2'x2' Panel surface mounting with high brightness LED package and unique pattern de-glaring PP diffuser and PS LGP de-glaring diffuser sheet for glare free uniform light distribution suitable for surface /recess mounting applications as specified and directed. Make -Philips full glow surface mount complete all as specified and directed. Make:- Cat No. SM367LED 42S-6500 G6L54W54 PSU OD or equivalent make as specified in P.S.

M&L for energy saver LED batten fitting 20 watt, 230 Volts, single tube mounting including with electronic driver LED Printed board, end cover, connector box etc and accessories, prewired, LED including required fixing arrangements and electrical connection two core copper cable from ceiling rose to led light fitting complete all as specified and directed.

M&L for energy saver LED batten fitting 10 watt, 230 Volts, single tube mounting including with electronic driver LED Printed board, end cover, connector box etc and accessories, prewired, LED including required fixing arrangements and electrical connection two core copper cable from ceiling rose to led light fitting all as directed . Make Philips/Wipro/ Havells

Supply only in replacement LED tube rod 4 feet long of 20/21 watt ultra bright tube light with very high efficiency single side connection situated for installation in existing T5/T8 with G13 Lamp holder 6500K complete all as specified and directed.

Supply and fix in replacement of Ultra bright LED PLL with very high efficacy suited for installation in existing 2G11 lamp holders to give glare free light complete all as specified and directed.

Supply ,fixing, testing and connecting LED Security light fittings 42 Watts , IP-65 cast aluminum housing in grey hammer tone stove enammelled finish outside with electric connection of Electronic driver and LED panel to be suitable size of copper cable with base plate and complete all as specified and as directed. Make - Philips Cat Part No. BRP331 LED 42 CW R5NPC PSU S1V1 or equivalent make as specified in P.S.

S&F sheet metal enclosure TPNL MCCB DB 4way, 415 V (vertical type) with bus bar double door type IP 43 - IK 09 for DB when MCCB 125 Amps (as incomer) to be used, fixed properly on / in concealed position and to provide required sizes of flexible conduit at any open surfaces near DBs for cables/wires complete all as specified and directed.

S&F double door metallic sheet metal enclosure for DB when MCBs to be used TPNL, 4 ways, 415Volts (horizontal type) with 200 Amps rated bus bar IP 43 - IK 09 suitable for TPN MCB/ 4 pole Isolator fixed properly on in concealed position and to provide required sizes of flexible conduit at any open surfaces near DBs for cables/wires complete all as specified and directed.

S&F, in replacement, double door metallic sheet metal enclosure for DB when MCBs to be used SPN 8 ways, 240 V with 200Amps rated bus bar IP 43 - IK 09 complete fixed properly on in concealed position and to provide required sizes of flexible conduit at any open surfaces near DBs of cables/wires complete all as specified and directed.

S&F, in replacement, double door metallic sheet metal enclosure for DB when MCBs to be used SPN 4 ways, 240 V with 200Amps rated bus bar IP 43 - IK 09 complete fixed properly on in concealed position and to provide required sizes of flexible conduit at any open surfaces near DBs of cables/wires complete all as specified and directed.

S&F in replacement , testing and commissioning MCB SP 240 volt 6 Amp to 32 amp 10 KA capacity having C-curve characteristics connected with suitable lugs complete all as specified and directed.

S&F MCB SPN 16-32 Amps complete all as specified and directed.

S&F MCB TP 40-63 A 415V complete all as specified and directed.

S&F MCB TPN 40-63 Amps complete all as specified and directed.

S&F MCCB 125 Amps, 4 Pole, 415V, 25KA complete all as specified and directed.

Supply and fix CRCA sheet metal enclosure 3mm thick, powder coated, IP-42 protection, front opening, comprising one incommer MCCB 125 Amp 25 KA,4 Pole , 05 separate compartment for energy meter to be housed with locking arrangement and 05 Nos MCB SPN 63 Amp 10 KA , 04 Nos copper busbar suitable for 200 amp strip type, complete prewired with 10 sqmm copper wire with suitable size lugs, duly housed on wall with grouting 10mm dia stainless steel nuts and bolts, including earthing link, Phase indicator, Amp meter, volt meter digital type, MCB SPN-05 Nos complete all as specified and directed.

Supply and fix CRCA sheet metal enclosure 3mm thick, powder coated, IP-42 protection, front opening, comprising one incommer MCCB 100 Amp 25 KA,4 Pole , 07 separate compartment for energy meter to be housed with locking arrangement and 07 Nos MCB SPN 40 Amp 10 KA , 04 Nos copper busbar suitable for 200 amp strip type, complete prewired with 10 sqmm copper wire with suitable size lugs, duly housed on wall with grouting 10mm dia stainless steel nuts and bolts, including earthing link, Phase indicator, Amp meter, volt meter digital type, MCB SPN-07 Nos complete all as specified and directed.

Taking down energy electric meter(KWH) with old /broken wooden meter box and re-fix the same in new PVC board box of size 900 mm x 450 mm x 30 mm including making hooks/ bracket on board , and painting and PCC works if required to hold all as specified and directed.

S&F (in replacement) Post Top lantern Fitting aluminum sheet spun polyurethane paint (with prior treatments) canopy & transparent imported acrylic cover B22 ABS holder cast aluminum spigot pole entry provided 52 mm suitable for 12 to 20 W LED Bulb including all fixing accessories complete all as specified and as directed by Engineer -in-charge.

M&L (in replacement) for 50 mm bore GI tubing medium grade of length 1.2 mtr with all necessary fittings for as a garden post pole including 2 Nos mild steel FI clamps 35x3 mm size to support pipe with pole , including PCC Work ,painting complete all as specified and directed.

Supply, laying & testing PVC insulated, PVC sheathed cable galvanized steel strip or wire armoured, electric control cables (Heavy duty) with stranded copper conductor of size 1.5 sq mm ,3 core, 1100 Volts grade.

M& L for repairing of unserviceable Gate light/garden light of any type/make by replacing burn out/worn-out/ weak LED lamp of any watt and re- fixing the fitting in position after repair and testing complete.

M&L for replacement of Lamp holder of Gate light/garden light fitting complete all as specified and directed

Supply & fixing in replacement of worn out/rusted sunken box of any sizes as per site requirement with pressed MS/GI steel terminal boxes of depth not less than 50 mm, flush type of thickness lot less than 1.60 mm along with new 3.0 mm thick plastic laminated sheet cover of suitable size including cutting/drilling hole and fixing switches, sockets, fan regulator etc as removed from old sheet and fitted with cadmium plated screw washer and making good to disturbed surface with cement mortar complete in all respect as specified and directed.

M&L for earthing complete with M.S. galvanized earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (earth pit not less than 2.25 M deep below normal GL) with top edge of the earth plate not less than 1.5M below normal GL, connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts & washers of GI or steel incl excavation, PCC (1:3:6) type C-1 chamber with RCC cover (1:2:4) type B0, 40 mm thick reinforced with 6 mm dia bar, 3 Nos. both way, 15 mm dia light grade GI protection pipe, funnel with wire mesh, watering pipe of size 20 mm dia med. grade, lugs, main Earthing lead upto 7.5 mtr incl. Charcoal dust, salt etc. all as shown in electrical plate No. 3 of SSR Pt-I, 2009 specification.

M&L for cutting / boring of PCC/hard standing at a depth not more than 15 cm deep and 15 cm in breadth for passing earthing conductor and making good the disturbed surfaces with PCC (1:2:4) type B-0 or cement mortar (1:3) complete all as specified.

Supply and fixing of GI pipe light grade of size 15 mm bore for laying in trenches/floors or walls including all fittings for fixing complete as required and directed by Engineer-in-Charge.

M&L for earth continuity conductor or main earthing lead 4 mm dia GI or steel wire fixed to wall on batten or recessed or buried in ground or drawn in conduit/pipe all as required at site.

Supply and fixing in replacement of worn out wooden batten/PVC Conduit with Non Metallic Rigid PVC conduit/casing caping of 20/25 mm size, ISI Marked, conforming to IS 9537 Part III, medium grade including all fittings like bends, elbow reducer, junction boxes, tee bell mouth all fixing accessories such as coupler lock, nuts, saddles pipe hooks etc complete in all respect as specified and directed.

Schedule of Credit (MINUS) Rs. 161144.00 B/F from Serial Page No. [Note : Details of items for schedule of credit is given on Srl Page No. ] This amount shall be automatically deducted to arrive at tendered sum

Mohinder Pal and Sons (BID ID -3071327)

DINESH ELECTRICALS (BID ID -3068694)

Ambrish Builders (BID ID -3061089)

R.K.ASSOCIATES (BID ID -3069039)