RENOVATION OF HOUSE NO. 12 TYPE 6 (OLD) SECTOR 7 CHANADIGARH.

Dismantling of ceramic tiles or vitrified and plaster to making the surface clean for refixing the glazed tiles including removing of malba complete in all respect and to the entire satisfaction of the Engineer in charge.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement:4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. Thetiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of size Size of Tile 600 x 600 mm

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm

Providing and fixing Ist quality glazed vitrified wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with Classic grey tile adhesive @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. size of tile 600 x 1200 mm

Providing and laying antiskid vitrified floor tiles of specified size (thickness to be specified by the manufacturer) of 1st quality with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand).The tiles are to be fixed by provding 2 mm thick spacer. The area of spacer is to be filled by using cement based grout of approved shade. The grooves are to be filled with cemenitious grout mix with proportion of 0.90 kg grout and 0.10 kg of hardener for each kg of filling material complete in all respect and to entire statisfaction of Engineer-in-Charge. Size of Tile 300x300 mm.

Providing and fixing 15 to 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. (GRANITE).

Providing and fixing 8mm thick wooden laminated floor class of use 31/23 having wear resistance level of AC-3 as per EN-13329 with a direct pressure laminate surface including profile, treated with aluminium side, flooring of approved colour and shade complete in all respects and to the entire satisfaction of the Engineer in charge.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Providing and Fixing 35mm thick 2nd class teak wood (kiln seasoned) panel door shutter consisting of 100mm x 35 mm style and top rail 150 mm x 35 mm lock rail 200mm x 35 mm bottom rail, teak wood (kiln seasoned) beading, with necessary 3 Nos. of hinges, S.S. Tower bolts, S.S. Handles 5”, sliding bolt and complete fixed in position including melamine polish complete in all respect to the entire satisfaction of Engineer-in-Charge

Providing and fixing 35mm thick second class teak wood (kiln seasoned) wire gauge window shutters consisting of vertical and horizontal styles 75x35mm size with wire mesh 22 x 12mm gauge fixed with 1/2" x 3/4" teak wood beading. The rate further includes the cost of 3" butt hinges stainless steel tower bolts 4", 4" stainless steel handle 2nos, stay 1no, screws, nails etc. I-hook, french spirit polishing two or more coats complete in all respect to the entire satisfaction of Engineer-in-charge.

Providing and fixing 35mm thick 2nd class teak wood (kiln seasoned) glazed window shutters consisting of vertical and horizontal styles 75x35mm size with 4mm thick floated glass pane fixed with 1/2"x3/4" teak wood (kiln seasoned) beading. The rate further includes the cost of 3" butt hinges, S.S. Tower bolts 4", S.S. handles 2 nos. I-hook and two coats of Spirit Polish after preparation of surface (special quality) complete in all respect to the entire satisfaction of Engineer-in-charge.

Providing and Fixing 35mm thick 2nd class teak wood (kiln seasoned) wire gauge door shutter consisting of 100mm x 35 mm style and top rail 150 mm x 35 mm lock rail 200mm x 35 mm bottom rail wire mesh 22 x 12 mm gauge fixed with 1/2” x 3/4” teak wood (kiln seasoned) beading, incluuding Stainless Steel fittings and french spirit polish, complete fixed in position and in all respect to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 2nd class teak wood (kiln seasoned) chowkhat 4 1/2" x 2 1/4"including cost of corner straps, iron hold fasts, hinges, screws,nails, fevicol etc. and spirit polish of chowkhats. Rate includes the cost of dismantling of all damaged chowkhats and making good the damage to walls plaster and floors as required including, disposal of rubbish to the dumping ground the rate further includes the cost of two coats Spirit polish complete in all respect and to the entire satisfaction of Engineer-in-Charge

12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

Providing and fixing wooden cabinet of 13½” deep and 2’-0" height with open able shutter at wall above 4’-9" height consisting of 19mm thick with commercial board (ISI marked) lipped with teak wood lipping of 19mm x 6mm on exposed edges include cost of nail, screws, auto hinges, synthetic adhesive etc. The front shutter and sides are to be furnished with 1mm thick ISI marked superior quality mica of approved shade and inner side of the cabinet with 0.8mm thick mica of approved shade fixed in position with help of wooden gutties at wall complete in al respect to the entire satisfaction of Engineer in charge.

Providing and fixing of kitchen cabinet below working shelves made out with 19mm thick commercial ISI marked plyboard and front portion of the cabinet furnished with 1mm thick superior quality sun mica of outer side and 0.8mm thick sun mica inner side of the cabinet for fixing the kitchen accessories and jack at bottom synthetic enamel paint over remaining portion. It is also include the cost of sprit polishing on the edge of the lipping cost of stainless steel handle, adhesive, nail, screws etc. complete fixed in position to the entire satisfaction of Engineer-in-Charge.

Provding and installation of precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by the Engineer in charge) 0.50mm +-5% total coated thickness TCT) thick zinc coating 100gsm as per IS 277 in 240mpa steel grade, 5-4 microns epopxy primer on both sides of the sheet and polyester top coat of 15-18 microns. Sheet should have protective guard film of 25 micron minimum to avoid scratches while transportation and should be supplied in single length upto 12 metres or as desired by the Engineer in charge. The sheet shall be fixed by using self drilling / self tapping screws of size (5.5x55mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with whitel ead complete upto any pitch in horizontal / vertical or curved surface excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required complete in all repsects and to the entire satisfaction of the Engineer in charge.

Providing and fixing Stainless steel sliding door bolts, ISI marked, transparent or dyed to required colour or shade, with nuts and screws etc. complete. 300x16 mm

Providing and fixing Stainless steel sliding door bolts, ISI marked, transparent or dyed to required colour or shade, with nuts and screws etc. complete. 250x16 mm

Providing and fixing Stainless steel tower bolts, ISI marked,transparent or dyed to required colour or shade, with necessary screws etc. complete. 250x10 mm

Providing and fixing Stainless steel Tower bolts, ISI marked,transparent or dyed to required colour or shade, with necessary screws etc. complete. 200x10 mm

Providing and fixing Stainless steel tower bolts, ISI marked, transparent or dyed to required colour or shade, with necessary screws etc. complete. 150x10 mm

Providing and fixing Stainless steel tower bolts, ISI marked, transparent or dyed to required colour or shade, with necessary screws etc. complete. 100x10 mm

Providing and fixing Stainless steel handles, ISI marked, transparent or dyed to required colour or shade, with necessary screws etc. complete. 125 mm

Providing and fixing Stainless steel handles, ISI marked, anodised transparent or dyed to required colour or shade, with necessary screws etc. complete. 100 mm

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body,door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing aluminium hanging floor door stopper, ISi marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. 9.101.1 Single rubber stopper

Providing and fixing heavy duty S.S. kitchen hydraulic auto hinges accessories i.e. hydraulic auto hinges fixing in the existing cabinet complete in all respects and to the entire satisfaction of the Engineer in charge

Providing and fixing heavy duty telescopic channel for drawers 18" to be fixed with necessary screws complete in all respects and to the entire satisfaction of the Engineer in charge.

Please Enable Macros to View BoQ information