PROVISION OF FOL SHED NEAR BLDG NO TB248 PATHWAY BATHROOM WITH TOILET AT OR LIVING LINES ABC AND D COY BR AND EM WORKS AND SPECIAL REPAIRS REPLACEMENT OF WATER SUPPLY PIPE LINES MOTORS STORAGE TANK AND CONNECTED ITEMS AT BAISAKHI OF AGE B/R P AND AG

Amount

Demolition of cement concrete (un-reinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) all as specified and directed by Engr-in-Charge.

M&L for 75mm thick PCC type C-2, 1:3:6 (40mm graded aggregate) as in sub-base, floors and pavings etc complete all as secified and directed.

M&L for 20mm thick Screed bed or bedding layer of cement mortar 1:6 for laying floor finishes complete all as specifie as directed.

M&L for Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigment comlete all as secified and directed by Engr-In-Charge.

M&L for Providing, plain cement concrete type B-1, (1:2:4) using 20 mm graded aggregate in roof kerbs or mud stops, rounded or chamfered on edges comlete all as secified and directed by Engr-In-Charge.

Excavating in post holes (or similar holes) each n.exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in hard / dense soil.

Surface dressing n exc 15 cm deep in hard/dense soil complete all as specified and directed.

M&L for Hard core, (broken srone or boulders) broken to gauge exc 63 mm and n exc 100mm complete all as specified and directed.

M&L for 100mm thick Cement concrete type C-2, 1:3:6 (using 40mm graded agg) as in foundations, filling and mass concrete all as specified and directed by Engr-in-Charge.

M&L for PCC 1:2:4 type B-2 using (40 mm graded stone aggregate) in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases).

S & F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete as specified.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, ridge , Gutter, Gable flashing, corner flashing etc, fixed with self tapping screws all as specified and directed by Engr-in-Charge.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, ridge , Gutter, Gable flashing, corner flashing etc, fixed with self tapping screws as specified and directed.

M&L for preparation of newly steel surface of any description, over 10cm in width or girth,not otherwise described with two coat of synthetic enamel paint over a coat of red oxide primer all as specified and directed by Engr-in-Charge.

Supply and fix, 0.63 mm thick corrugated galvanised mild steel sheeting (minimum 275gm/sqm galvanising) with two corrugations side lap, fixed with L type or J type or cranked hooks , bolts and washer in roof, complete, all as specified and directed.

Supply and fix 0.80mm thickness (minimum 275gm/sqm galvanising) plain galvanised mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashing of complete all as specified and directed.

Material and labour for preparation of new steel surfaces of any description, over 10 cm width or girth not other wise described including degalvanising with mordant solution and applying two coats synthetic enamel paint over of Mordent Solution roof paint over a coat of red oxide primer complete all as specified and directed.

Excavation in trenches n. exc 1.5 m wide and n.exc 1.5 m deep for foundation and getting out in hard/dense soil.

Returning/filling in including spreading, levelling, watering and well remming in layers n.exc 25 cm in hard/dense soil.

Removing excavated material n.exc 50m and depositing where directed at a level n exc 1.5m above the starting point.

M&L for cement concrete type D-2, 1:4:8 in Cement concrete in foundations, filling and mass concrete all as specified and directed by Engr-in-Charge.

M&L for plain cement concrete 75mm thick type C-2, 1:3:6, (40mm graded stone aggregate) as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement with all as specified and directed by Engr-in-Charge.

M&L for PCC 1:3:6 type C-1(20 mm graded aggregate) precast cement concrete block masonry with solid blocks exc 10 cm in width and setting in CM 1:6 etc complete.

M&L rendering 15mm thick in CM 1:6 on concrete inner surfaces finished even and smooth without using extra cement .

M&L rendering 15mm thick in CM 1:4 on concrete outer surfaces finished even and smooth without using extra cement .

M&L for Prepairing surfaces plastered or unplastered newly surfaces with two coats of cement base paint over one coat of white wash as completed.

M & L for 350 x 250 x7 mm or 450x350x7mm thick glazed coloured ceramic tiles on vertical surface of wall set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade. (Make; Kajaria/ Orient Bell/ Johnson/ Somany). Note :- Colour and pattern will be decided by GE/Engr-in-charge. Contractor will bought the tiles only after approval of colour and pattern of tile by GE/Engr-in-charge.

M&L for RCC (Nominal Mix) type B-1, 1:2:4 (20mm graded agg) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like with all as specified and directed.

Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips with all as specified and directed.

Mild steel TMT bars 6mm to 8mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips.

S&F PVC water storage tanks of 500 ltrs capacity rotational moulded (multi layered cylindrical vertical with closed top) hoisted and fixed in position all as specified

S&F PVC water storage tanks of 1000 ltrs capacity rotational moulded (multi layered cylindrical vertical with closed top) hoisted and fixed in position all as specified

S&F ball brass valves, high pressure, with polyethene float and flynut complete screwed for iron pipe of 20mm dia all as specified (Make:Jindal/Leader/Scico).

S&F Gun metal 20mm bore globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed with all as specified and directed.

M & L for screed bed or bedding layer of 15 mm thick for laying floor finishes in CM (1:6 ) with all as specified and directed.

M&L for Non-skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in vertical surfaces etc set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade . (Make; Kajaria/ Orient Bell/ Johnson/ Somany). Note :- Colour and pattern will be decided by GE/Engr-in-charge. Contractor will bought the tiles only after approval of colour and pattern of tile by GE/Engr-in-charge.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurrypointed in white cement to match completed all as specified & directed

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width tuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of lain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

M&L rolled mild steel for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) incl distance pieces, cleats etc, Fe-290 (Gde E- 165).

M&L for Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed with all as specified and directed.

M&L for painting wooden surfaces of any description, not other wise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer with all as specified and directed.

S & F 30mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass, gauze etc but divided into squares, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for window, ventilators etc are provided with stiles and rails as specified in SSR Part-1, section 8 clause 8.24(b).

S& F for 30mm thick Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats.

S&F 2nd class HW 30mm thick Glazed and skeleton shutters, divided into squared, with plain, chamfered or roun0ded, mitred and rebated sash bars, any numbers open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a); supplied and fitted to chowkats

S&F 100mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed.

S&F 75mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed.

S&F 150mm long aluminium anodized, barrel tower bolts extruded section.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodised. handle fabricated type.

Supply & fix aluminium alloy, anodised, sliding door bolts 250mm size with hasp, staple (bolt type) and fixing clips of sheets , cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed etc complete all as specified and directed.

S&F vitreous china wash hand basin white flat back of size 550mmx400 mm including CI brackets and waste pipe complete all as specified and directed(Make: Hindware/Parryware)

S&F 32mm dia waste coupling of PTMT (half or full threaded). (Minimum weight 32mm- 45gms/40mm-60 gms) with waste pipe complete all as specified and directed.

S & F fancy typy chromium plated 15mm dia pillar taps fancy type copper alloy with capstan heads, screwed down high pressure, with or without lettered "hot or cold" with long screwed shanks and fly nuts, screwed for iron pipe and fixed.

Supply and fix chromium plated brass Bib taps,cast copper alloywith crutch or butterfly handle, screwed down for iron pipe for 15mm bore GI tubing complete all as specified and directed by Eng-in-charge.

S&F PVC (SWR) pipes 110mm dia single sockted in any length with rubber ring joints laid in trenches or floors with all as specified and directed.

M&L cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate) to bed of drain pipes including packing under and haunching against the sides of pipes, after they are laid and tested for 110 mm bore pipe complete all as specified and directed

S&F PVC (SWR) bends any radius with access door, 110mm dia with all as specified and directed.

S&F PVC (SWR) bends any radius with access door, 75mm dia.

S&F PVC (SWR) junction single, (Single T) equal or unequal of dia110mm.

S&F PVC (SWR) junction single, (Single T) equal or unequal of dia75mm.

S&F PVC (SWR) pipes 75mm dia single sockted in any length with rubber ring joints laid in trenches or floors..

S&F 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement.

S&F 20mm outer dia 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc with all as specified and directed.

S&F 25mm outer dia 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc with all as specified and directed.

S&F PVC connection of 15 mm size with PTMT nuts of length 450 mm with all as specified and directed.

S&F Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 190gms) with all as specified and directed.

S&F Vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket etc. (excluding flushing cistern & flush pipe) complete in all respect all as specified.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified and directed.

S&F Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S & F Vitreous China squatting pan, "Orissa" pattern, size 580 x440 mm white, with integral foot rest (excluding flusing cistern and flush pipe).

S & F 10 litres PVC, valve less, Syphonic action type, Flushing cistern low level, white with inlet ball valve float chain and pull and brackets complete.

S & F fancy type chromium plated 20mm dia stop valve , cast copper alloy with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete all as specified

S & F fancy type chromium plated 15mm dia stop valve , cast copper alloy with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete all as specified

S&F Mild steel flat iron as in hold fasts; complete all as specified.

M&L Plain Cement concrete type C-2, 1:3:6, (40mm graded agg) in surface channels and drains

M&L PCC type C-2, 1:3:6 (40mm graded agg) in walls, Drain walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases) complete all as specified and directed.

M&L for RCC 1:2:4 type B 1 (Using 20 mm graded aggregate ) Foundations, including rafts,footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete

M&L for RCC type B1 1:2:4 (Using 20 mm graded aggregate for Columns, pillars, piers, posts and struts

M&L for RCC type B1 ,1:2:4 (using 20 mm graded aggregate) for beams and the like.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter,add for fair finished .

M&L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions.

M&L for preparation of new surfaces of walls, plastered or unplastered including cornices, pilasters etc and applying two coat of colour wash over one coat of white wash all as specified.

M&L for mild steel work as in wind ties for roof covering including securing bolts etc. including all necessary drilling, bolting or riveting etc and similar work conforming to Fe 290 Gde E-165 all as specified and directed by Engineer-in-Charge.

Supply & fix sheet glass 3mm thick ordinary quality and glazing with oil putty in squares n.exc 0.50 Sqm in each pane, complete all as specified and directed.

Material & Labour for Point/fan wiring with 1.5 sq mm (nominal area), PVC insulated unsheathed (HRFR), 1100 volts grade, multi-stranded copper conductor, in and including PVC casing capping of adequate size with all fittings and accessories including PVC boxes for housing the switches ( Make of box Prestoplast,Prestoteak), including PVC insulated and unsheathed (HRFR)single core multi-stranded copper conductor cable of size 1.5 sq mm green in colour as earth continuity conductor connected to common earth dolly complete all as specified and directed.

All as per item No. 86 here in before One 3 pin socket outlet, 5 Amps on the same board with other switches, with cables 1.5 sq. mm size

All as per item No. 86 here in before but for one 3 pin socket outlet 5 Amps three pin controlled by one switch on independent board complete all as specified directed.

All as per item No. 86 here in before but for one 5 pin socket outlet 15 Amp and 5 Amp Multipurpose independent using 2.5 Sqmm copper conductor cable (multi-strand) PVC insulated and unsheathed cable and 2.5 sqmm copper (multistrand) PVC insulated and unsheathed earth wire with PVC boxes complete all as specified.

S&F Socket outlet 2 in 1, 3 pin, 5 amp flush type

S&F Socket outlet 2 in 1, 3 pin, 5 and 15 amp flush type

Supply & fixing switch piano flush type (ISI marked), single pole, one way 15 Amp, 240 Volts complete all as specified & directed.

Supply and fixing ceiling rose, surface bakelite, 65mm x 50mm , two to three terminals complete all as specified & directed.

Supply & fixing switch piano flush type (ISI marked), single pole, one way 5 Amp, 240 Volts complete all as specified & directed.

Supply and fixing lamp holder, insuleted body with pack plate suitable batten fitting on wall duly grouted/fixed in solid block wall or on wooden board complete all as specified and directed.

S&F LED lamp 10 Watt, CDL, B-22 cap, (Pin type), 230W, PF not less tha 0.85 (min). Make- Havells/Crompton/Syska

S&F LED bulkhead fitting 10 watt (Endura Ruby) with all accessories and including connenting up with twin core twisted with flexible copper conductor cable with suitable size of 230 volts , 50 hz complete all as spicified and directed.

S&F regel batten for LED Tube universal batten for G 13 T8 lamps including making electric connection from Ceiling Rose to tube light fitting including Photon Ultra plus LED Tubelight 20 W (single side connection) Ultra bright LED Polycarbonate Tubelight with 10% THD with very high efficiency suited for installation T8 Tubelight with G13 Lamp holders to give glare free light and mounting casing box 2 Nos complete all as specified and directed

S&F of new generation energy saving and environmental friendly long life LED building security light made up of innovative die cast aluminium housing high power LED as lighting source with IP - 66 power consumption 35 watt complete input voltage of 150-240 Volt (nominal rated voltage 240 Volt) complete including twisted 3 core copper cable of size 1.5 Sqmm dia for connecting phase, neutral and earth from ceiling rose to light length as required at site,GI bracket 32 mm dia pipe and 02 numbersclmaps, all fixing arrangements such as fastners, bilts, nuts washers etc all as specified and directed.

S & F of GI brackets for fixing LED building security light fitting fabricated out of GI tubing 32 mm dia, light grade, 0.9 mtr long , bend to 120 degree shape by cutting, welding and well finishing including MS clamp of flat iron of size 30 x 4 mm -02 Nos complete for fixing on wall including all fixing arrangements such as fastners, bilts, nuts, bolts washers etc including making good disturbed wall surfaces matching with the existing surface and finishing complete all as specified and directed by Engr in charge

Supply and fix sheet metal enclosures for DBs when MCBs to be used 230 volts 08 way 200 Amp rated busbar single pole and neutral fixed on wall duly grouted in solid block wall or on wooden board.

Supply and fix sheet metal enclosures for DBs when MCBs to be used 230 volts 04 way 200 Amp rated busbar single pole and neutral fixed on wall duly grouted in solid block wall or on wooden board.

S&F MCB SPN having braking capacity 10KA, 32 Amps, 240 V complete all as specified and directed.

S&F MCB SP having braking capacity 10KA, 6 to 32 Amps, 240 V complete all as specified and directed.

Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5mtr below the normal ground level connected to galvanised wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron.Earth wire protected by GI pipe 15 mm bore(medium grade) and connected to main switch board or main control board as directed and as specified and shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 40 cm x 40cm x 5cm reinforced with 8mm dia TMT bars @ 15cm C/C with one handle for lifting made out of 8mm dia bar, funnel, wire mesh, 20mm dia GI pipe medium grade for watering, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil and testing complete all as directed by Engineer-in-Charge.

S&F of 1100 Volts grade heavy duty ISI marked cable PVC insulated multi stranded aluminium conductor one twin core cable flat or circular of size 16 sqmm served with inner sheathing of PVC tape & overall PVC sheathed in service connections , of size 10 Smm 2 core. Make :- Havells/ Plaza cables/ polycab /Finolex

Supply and fixing LED light fitting 1 x 20 Watt 220 volt AC decorative box type with driver, holder including LED tub light connecting up with three core flexible copper conductor cable of size from ceiling rose complete all as directed.

S&F metal plug and socket assembly, SPN sheet metal enclouser with a two pin and earth plug and socket complete with one SP, MCB 20Amp "C" curve fixed flush to wall/other surface complete all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm

Supply and fixing ceiling rose, surface bakelite, 65mm x 50mm , two to three terminals complete all as specified & directed.

Supply and fix electric water heater(Geyser), storage type steel body with copper inner tank and heating element up to 2 KW capacity 25 litre, BEE 5 star rated adjustable temprature setting 0-90 degree C complete with accessories such as safety wall, thermostate, NRV indication lamps, inlet outlet connections,air vent connections, connection pieces including all fixing arrangements such as fastners, bilts, nuts washers etc including making good disturbed wall surfaces matching with the existing surface and finishing complete all as specified and directed by Engr in charge

S & F inreplacement incl leakage testing galvanised steel water tubing medium grade 50 mm dia bore with all fittings such as bends, elbow, socket, reducer etc,connecting pipe to PVC tank through connectors as required at site, laid under floor / trenches all as specified & directed.

S&F inreplacement of PVC water storage tanks of 5000 ltrs capacity rotational moulded (3 layered cylindrical vertical with closed top) ISI marked hoisted and fixed in position complete all as specified and directed.

Dismantling of electric connection from centrifugal pumping set of 5 HP inclding disconnection electric supply and taking down of electric driven motor for replacement and depositing into MES yard as specified and directed.

Supply & install monoblock pumping set 5 HP, centrifugal, elecric driven, AC 3 phase including suction and delivery 50 mm of discharge 25 LPS at 30 mtr head complete including Automatic star delta starter and multistranded copper conductor 10 sqmm single core from starter to motor for star delta connection to each motor separately (01 N working & 01 N standy by)

S&F 3 layer 63 mm dia PP-R polypropylene random copolymer pipes SDR 7.4 (PN 16) UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and directed.

S&F 3 layer 50 mm dia PP-R polypropylene random copolymer pipes SDR 7.4 (PN 16) UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and directed.

S&F 3 layer 40 mm dia PP-R polypropylene random copolymer pipes SDR 7.4 (PN 16) UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and directed.

Supply and fix 63 mm bore outer dia PPR gave valve brass insert complete all as specified and directed.

Supply and fix 50 mm bore outer dia PPR gave valve brass insert complete all as specified and directed.

Supply and fix 40 mm bore outer dia PPR gave valve brass insert complete all as specified and directed.

M & L for 15mm thick rendering on fair faces of brick,stone work/concrete surfaces of wall in CM (1:4), finished surface even and smooth without using extra cement complete all as specified and as directed.

M&L for PCC 1:3:6 Type C2 for foundation of platform, mass concrete with 40 mm gradede coarse agreegete complete all as specified and as directed.

M&L for Construction of Valve pit of size 1050cm x 1050cm x 900cm (internal dimensions) with Brick masonry construction including all necessary excavation and earth work in hard/ dense soil,returning,filling,in disposal of surplus soil to a distance not exceeding 50 m and depositing where directed , PCC in foundation of the mix (1:4:8) Type D-2 (using 40 mm graded crushed stone aggregate), PCC Pocing in PCC(1:2:4), type B0 using 12.5m crushed graded aggregate, brick masonry work in cement mortar (1:4) rendering,15 mm thick in cement mortar (1:4) internally,finished even and fair and pointing in CM 1:3 flush pointing externally . Mild steel angle iron 50x50x6mm frame work ,MS sheet cover with 3.15mm thick with handle made of flat iron 30x5 mm thick and locking arrangment including providing pad lock ( Godrej/Link/Horisson ) 50 mm size Brass , and applying two coats of synthetic enamel paint of tint as approved over a coat of red oxide primer to all mild steel surfaces and providing two coats of black bituminous paint to all embedded portion of mild steel work etc. complete all as specified and shown on drawing.

Supply, laying & testing in repalcement cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminum conductor, 1100V grade with stranded aluminium conductor of size 16 sqmm 4 core including taking down of old unserviceable UG cable

M & L for laying of fine, clean sand (river sand) free from sharp materials and stone particals in trenches for cushioning of cable 8 cm thick under cable and 15 cm thick over the cable including gently punning complete all as specified and directed. Note:- The total thickness of sand shall be measured 18 cm after punning with all as specified and directed.

Supplying and laying un-reinforced precast concerete cable cover, class LV, type 1 flat size 250mm x150mm x 40mm for cable protection , laid flat ie length of cable cover shall be laid across the cable, complete casted with PCC 1:2:4 Type B1 using 20mm graded crushed stone aggregate with all as specified and directed by Engr-in-Charge.

M/S ASHOK CONSTRUCTION

mon traders

M/S MURPHEW ENTERPRISES

M/S P K ENTERPRISES

M/s Roltso Enterprises

M/S NIRMAL TRADERS

M/S T P ENTERPRISES