Internal Renovation Work Of Kanchan And Ketki Building At ACTREC, Kharghar, Navi Mumbai

Amount

Providing and Applying and Levelling the existing surface with Birla White Cement based / Coloured waterproof Putty of average thickness of 2 mm of approved thickness, brand and manufacture, over the plastered wall surface to prepare the surface even and smooth ready for painting purpose etc complete ( Rate inclusive of Scaffolding Material, Labour Charges) Etc. Only to be applied at distressed areas and newly plastered surface as per the instruction of Engineer incharge.

Providing & Applying one / two coats of primer & thereafter two coats of paint as mentioned First quality to the required colour scheme and as per manufacturers instructions / specifications to the walls, beams, columns, ceilings, partitions doors etc. filling up crevices and levelling with waterproof putty / plaster of paris of necessary to obtain smooth surface etc. complete job including removal of stains, painting spots on floors etc. as to the entire satisfaction of engineer in charge :With Acrylic emulsion paint two coats of primer and two coats of paint. ( Rate inclusive of scafflolding, labour charges, ladder etc.)

Providing and Erecting double bamboo scaffolding over entire external surface area of building & removing the same after completion of the work and providing and erecting polypropylene/polyethylene dust net along the periphery during the construction to control debris & dust from spreading beyond construction work as directed by consultant and engineer incharge. Front elevation shall be measured.

External Painting: Providing and applying One coat primer and one waterproof base coat and two coat of textured Elastomeric paint of approved make, quality and colour including scrapping the surface to remove all loosely adhered particles followed by washing with water then wire brush so as to ensure thorough cleaning and opening up all the visible cracks in the plaster, in V- groove fashion using electric cutter machine. Fill up these cracks with cement past and polymer in ration of 1:1. Finish the same to ensure crack matched plaster level all complete as per the instruction of engineer incharge.

Kota stone slabs 20 mm thick in risers of steps, skirting, dado, landing and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size - 600*600mm

Providing and laying Vitrified tiles in Dado in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size - 600*600mm

Providing and laying gang saw cut 18 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in-Charge.

Supply, laying, fixing, jointing, testing and commissioning of CPVC SCH 80 including all fittings such as sockets, unions, reducers, long or short bends, elbows, nipples, flanges, checknuts, clamps, z-pieces, male and female adapters etc all as per specifications along with necessary support required for concealing and supporting the shaft as per supplier specification. The rate includes cutting chipping & making good; along with necessary supports, anchor fastener and all accessories as per approved drawings and technical specification.

i) 80mm n.b

ii) 65mm n.b

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth beyond 45 cm of brick masonry chamber: With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Dismantling W.C. Pan/ EWC/ Indian WC of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in- Charge.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:4 (1 cement : 4 coarse sand)

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material outside ACTREC campus as per direction of Engineer-in-charge.

Dismantling carefully the existing and damaged cracked all types of flooring and dado etc and disposing the same outside the ACTREC campus as per the instruction of Engineer incharge.

Providing and laying in position cement concrete of specified grade including the cost of centering and shuttering : Plain cement concrete 1:3:6

Removing C.I./G.I. Pipe Up 100 to 300 mm diameter with fittings and clamps disposal of unserviceable material outside ACTREC campus as per direction of Engineer-in-charge.

Removing C.I./ G.I./PVC/CPVC pipes for any size with all fittings upto 100mm dia etc. and clamps disposal of unserviceable material outside ACTREC campus as per direction of Engineer-in-charge.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.

(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. Two Coats work

P.V.C. PIPES Schedule 40:Providing, laying, jointing, fitting, testing heavy quality P.V.C. pipes of Prince, Supreme etc. make & of required dia including all fittings required as per site requirement & laying the same at any floor levels including scaffolding all jointing materials & clamping in wooden blocks if required etc. complete as directed & specified by Engineer-In-Charge. - 75mm

P.V.C. PIPES:Providing, laying, jointing, fitting, testing heavy quality P.V.C. pipes of Prince, Supreme etc. make & of required dia including all fittings required as per site requirement & laying the same at any floor levels including scaffolding all jointing materials & clamping in wooden blocks if required etc. complete as directed & specified by Engineer-In-Charge. - 110mm

Supply, fixing, testing and commissioning of uPVC SWR Pipe confirming to IS 13592-92 TYPE B and fitting as per IS 14735-99 for Drainage including all fittings and with inspection doors, including supports brackets as per supplier specification and distance, cutting, chases/holes in walls/floors/slab etc. Item also includes branches and fittings inside toilet for easy jointing. 110mm

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 20 mm nominal dia Pipes

REMOVING WASH BASIN and pillar taps: Labour charges for removing existing damaged wash basin of any size & colour with all fittings & handing over the same with all fittings at required place to the department as directed by Engineer-In-Charge etc. complete.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require including PVC connector.

TOWEL ROD: Providing & fixing approved C.P. brass towel rods of size 600mm x 20mm heavy duty with a pair of C.P. brass brackets wall flanges etc. fixed to wall with C.P. screwed on the raw plugs etc. complete as and when required and as directed by the Engineer-In-Charge.

Hand Spray wth PVC connection of approved make (1M long) as per the instruction of engineer incharge.

C . P. Double nipple 15mm

C . P. Double nipple 20mm

P' OR 'S' TRAP: Providing & fixing heavy quality lead 'P' or 'S' trap with union cleaning eye at bottom white solder joints etc. complete as and when required and as directed by the Engineer-In-Charge. Extra if required.

Providing & fixing 100mm dia C.I heavy duty nahani trap as per the instruction of engineer incharge.

Providing and fixing Angle Stop Cock including all fittings required to fix it as per the instruction of Engineer incharge.

WATER PROOF PLASTER: Providing and laying water proofing treatment in flooring portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer ofslurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipesand masonry with polymer mixed slurry.

CUDDAPAH- Providing & laying 35mm thick cuddaph stone slabs in platforms/sinks with all exposed edges machine cut double machine polished in true plane and level with matching cement paste curing flinishing the joints neat etc. complete including making grooves in walls for fixing and making good the surfaces.

Providing & fixing in position anodised aluminium Three track window with frame such that one track is installed with mosquito net. For shutters of doors including sliding doors, windows & ventilators of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required includingcleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required.

Brick bat koba breaking including stacking of serviceable material and disposal of unserviceable material outside ACTREC campus as per direction of Engineer-in-charge.

Providing and laying water-proofing treatment of for sunk slabs of toilets and wherever necessary at all the levels with brick / stone aggregates (brick bat coba), with layer of 20 mm thick cement mortar 1:3 (1 part cement : 3 part coarse sand) mixed with water proofing compound of BASF, SUNANDA, FOSROC or approved make and as specified by the manufacturer, laying brick bats of required size in 100mm layers and providing cement mortar in between such that brick bat is impregnating in to the base mortar bed with gap of 12 mm all around according to slope, level and curing the same, the gaps around brick bats filled with cement mortar 1:3 (1 part cement : 3 part coarse sand) mixed with waterproofing compound, 20-30 mm layer above brick bats and finishing top with neat cement @ 2.75 Kg/Sq.M. screeding and curing etc. in line, level and plumb / slope, complete. (Note : The above rates shall be inclusive of Providing and mixing of waterproofing compound as per manufacturer's specifications and as decided by the Engineer incharge)

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required: Kitchen sink with drain board 510x1040 mm bowl depth 250 mm

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet with mixer arrangement for connection to the geyser.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge.

SITC of Main feeder piller panel IP 65 incomer 400A 415volt 3 ph , 50HZ , TP+N 400 A-50kA MCCB-FROH with cable spreader , Manual, with integral LSIG protection, 3x metering CTs, MFM(EM6459), R/G/A lamps , R Y B indication , Voltmeter , On OFF Trip Indication , Rotory operating knob from outside suitable for connection of 400sqmm cable , Pahse seperator , Protection sheet , Outgoing - 160A TPN MCCB 04 Nos , 63A TPN MCCB 02 Nos. The work aslo includes MS channel foundation required for installation of panel , painting work and complete as directed by EIC ES. Panel manufacturer to be CPRI approved.

SITC of Sub Distribution panel IP 65 double door type Incomer , 415 volt , 3ph , 50Hz, TP+N 160 A-50kA MCCB-FROH with cable spreader , Manual, with integral LSI protection, 3x metering CTs, MFM(EM6459), R/G/A lamps , R Y B Indication MFM meter , On OFF Trip Indication , Rotory operating knob from outside , control wirings , Control MCB for indication , Outgoing , 40A DP MCB 12 Nos C Curve , 40A DP RCCB 30MA leackage current for each circuit Qty 12 Nos , R Y B N copper Bus bar arrangements for proper distribution , single phase energy meter 10 Nos including control wirings, control MCB , required rating CT / PT , floor mounting incluidng MS channel foundation , painting and final finishing as required. Panel manufacturer to be CPRI approved.

Supply, installation ,testing & commissioning the following cable on wall/floor/ceiling/structure member or on cable trays or down through PVC pipes, using MS spacers and GI saddles, cable clamp etc. complete in all respect. Cable, conforming to IS: 1554/Part 1/1998, XLPE, Aluminium stranded conductor, armoured, 1100 V class 3.5 x 95 sq. mm A2XFY Aluminium Conductor for Main feeder panel to sub panel 04 runs including glanding , lugging , tagging and all fixing accessories

SITC of 8 Way SPN DB , Incomer 32DP MCB C Curve 01 Nos , Outgoing 10A SP MCB 05 Nos , 25A SP MCB 01Nos All MCB C Curve. Including Neutral bus bar arrangement earthing arrangements , wall fixing accessories complete in all respect , tagging , SLD as per details provided.

SITC of 22W 4feet LED light fixture including ceiling rose , and fixing accessores complete in all respect

SITC of 8W LED light fixture mirror light decorative type as approved by EIC ES

SITC of Angle holder for fixing Pin type LED lamps , including Male connector

SITC of 18 Watt LED lamps PIN Type

SITC of 15W to 18W LED square light Supply ,Installation,Testing & Commisioning of LED shaped Premium Range Recessed Downlighter having pressure die-cast aluminimum housing with white front bottom frame suitable to following features. - Luminaires suitable to Aluminium metal grid ceiling or Gypsum or POP, -Minimum System Lumen output 1500 lumens -In built electronic LED pre wired driver, -Luminaire shall be with special translucent --High Surge Protection:-2.5kV. -High diffuser>85%, -Provision of Spring loaded Mounting clips. -Opal Translucent cover/Poly Carbonate reflector. -CRI>80,THD<10%. -High Efficacy gretaer than or equal to 100 lm/watt, -Provide Uniform low glare lighting non yellowing/PMMA lens for better light distribution, -Operatable voltage - 220-240 V,50 Hz, PF>0.9, -Colour Temperature gretaer than or equal to 4800K. for bathroom and washroom

SITC Supplying and erecting regular/ standard model Ceiling fan of 1200 mm. sweep complete erected in position including ceiling fan hook fixing , down rods , ceiling rose and all fixing accessories

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

SITC of metal body exhaust fan 225mm including louvers outside. The work includes civil work required for installation of fan including final finishing and painting.

SITC of single phase Gyser 3 ltr electric operated including inlet and outlet SS pipe for water connection and including all fixing accessories.

SITC of wired Door bell with push button outside and control switch inside.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI / PVC box , and earthing concealed / surface the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Group A

SITC of Secondary point light to light looping light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit

SITC of 20A DP MCB C Curve type including metal body enclosure box and earthing arrangements.

Supplying and fixing following size/ modules, GI box / PVC box concealed / surface alongwith modular base & cover plate for modular switches in recess etc. as required.

3 Module

6 Module

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box concealed / surface including connections but excluding modular plate etc. as required.

Modular switch 6A/16A

Modular Socket 6A/16A

SITC of 20 pair armoured cable to be laid in DWC pipe( material included 25mm DWC ) through out required for telephone connectivity. 20 Pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, armored telephone cable in the surface/ recessed steel/ PVC conduit as required.

SITC of 2 x 20 ways telephone Tag block. Including crone connectors , and fixing accessories wall mounted complete in all respect.

SITC of modular type surface Television socket including modular box , face plate and conenctor

Supply, laying, testing & commissioning of RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath Television cable through casing capping/ PVC conduits/GI-MS pipes on any kind of surface as per requirment with all accessories and fixing arrangement all as per instructions & as directed by E-I-C, ES This including cassing cappings , PVC Conduicts as required.

SITC of Telephone socket (RJ -11)including modular box , faceplate and connector, including all fixing accessories surface / recess type as directed by EI ES.

SITC of Analogue key pad type caller ID telephone instruments including 2 pair wire and connection jack

SITC of CAT 6 LAN cable for DATA including 25mm PVC Conduit Supply ,Installation,Testing & Commisioning of of UTP 23 AWG 4 pair CAT 6 LAN Cable to TIA/ EIA 568 B.2.1.in the surface/ recessed steel/ PVC conduit as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable including surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable including surface/ recessed medium class PVC conduit as required. 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 50mm PVC conduit pipe for Main DB to SPN DB wiring circuits.

SITC of street light DB , incomer 40 amps DP ELMCB--1 No. /// 6/16 amps SP MCB-- 8 Nos. C Curve type including Digital timer in each distribution board , wall mounted fixing arrangement and all accessories as required

Supply ,Installation,Testing & Commisioning of 2 X 45 Watt LED or equivalent Street Light having pressure die-cast aluminimum housing with Coated with epoxy zinc phosphate primer and finished using environmentally stable polyurethane based paint , suitable to following features. - -In built electronic LED driver, -High Transmisivity diffuser>85%, -IP-65/67 -High Efficacy, -Provide Uniform low glare lighting , -CRI-70, -Warm White -Operating Temperature:--40 to +60 Celsius degree -Operatable voltage - 220-240 V,50 Hz, PF>0.9, -Colour Temperature-3000K. including outdoor IP 67 Junction box with connecting terminals , glands and lugs

SITC of Wall mounted street light bracket GI type with clamp and all fixing accessories for fixing of LED street lights

Supply, installation ,testing & commissioning the following cable on wall/floor/ceiling/structure member or on cable trays or down through PVC pipes, using MS spacers and GI saddles, cable clamp etc. complete in all respect. Cable, conforming to IS: 1554/Part 1/1998, XLPE, copper conductor, armoured, 1100 V class 3Cx4 sq.mm 2XY Copper Conductors

Supply & Fixing of casing capping of following suitable size with screws, rawal plug etc. along with all accessories complete in all respect on any hard surface/wall/trench/ceiling etc. Complete as per instructions of EIC. Casing capping 32 mm

Tinned copper earth plate electrode 600 x 600 x 3.15 mm earth station, 2.5 mtr below ground level as per drawing complete with all required materials like Cole, charcoal, salt, brass nut bolts & washers, watering arrangements, GI pipe (B class), concrete chamber, heavy duty cast iron cover plate & excavation in all types of soil in ground refilling & removal excess earth within a radius of 500 mtr. Etc. (2 Nos, of neutral earthing of T/F, 2 Nos. for T/f body earthing & 2 Nos. for panel earthing)Note:1.The chamber cover & plate shall be of heavy-duty hinged type & it shall weigh approx. 65 to 75 Kgs. For 450 x 450 mm size & shall be got approved by dept. (6 mm chequred plate with 40 x 40 x 6 mm angle iron frame)2.Plastering shall be done both inside & out side.3.The measurement of resistance of earth station & resistance of complete scheme of earthing layout shall be measured, recorded & got approved by Engg-in-charge.

Supply, Installation, Testing and commissioning of 25 mm x 3 mm COPPER strip on surface or in recess for connections etc as required

SITC of CCTV survelliance system including 04 Nos IP CAMERA 2 MP including all fixing accessories outdoor type IP 67 , including Junction box , cable connection, dome type clear night vision , Motion operated , wifi connected , POE operated , vendal proof , inbuilt memory card 128 GB , to be integrated with existing CCTV system in campus. The work also includes SITC of 8 port PoE Network Switch’s, Gigabit Ethernet Web Smart chassis in a 1U form factor with 24 x 10/100/1000 PoE Base-T ports, 2 fixed SFP (1G) with internal power supply (192W PoE budget). POE switch 8 port , including complete configuration and integration of all 04 cameras ,POE switch to existing CCTV system in campus. 6U wall mounted rack for fixing POE switch including all fixing accessories. Medial converter 02 Nos

SITC of CAT 6 LAN cable for DATA including 25mm PVC Conduit Supply ,Installation,Testing & Commisioning of of UTP 23 AWG 4 pair CAT 6 LAN Cable to TIA/ EIA 568 B.2.1.in the surface/ recessed steel/ PVC conduit as required.

SITC of Cat 6 type I/O with RJ 45 socket with Box, faceplate and fixing screws, having the compliance/certifications for ISO 9001:2015 & ROHS

SITC of IT rack -19" Wall mounted rack 15U(double section) 600mm X600 Mm with acrylic glass door with the accessories -[Two Fan position tray with two 90 CFM fans(AC 230V),3 Horizontal cable manager- 3nos, AC power panel strip with 5 X 5 AMP sockets ,fuse and on/off switch, 1 packet mounting hardware

Supply ,Installation (rack dressing)Testing & Commissioning of 1 meter length, UTP Patch cord of Cat 6 type having the compliance/certifications for ISO 9001:2015 & ROHS

Supply ,Installation, Testing & Commissioning of 3 meter length, UTP Patch cord of Cat 6 type, having the compliance/certifications for ISO 9001:2015 & ROHS

OS2 Lazrspeed fully loaded fibre tray which includes LC TO LC adaptors, pigtails, splice protectors etc for the termination of 12 core Single mode fibre with suitable required numbers of fibre patch chords (4 nos)having the compliance/certifications for ISO 9001:2015 & ROHS

Supply, Installation, Testing & Commissioning of fully loaded RJ 45 24 port Patch Panel with tool-less keystone jacks having the compliance/certifications for ISO 9001:2015 & ROHS

KUMAWAT INFRASTRUCTURE

B G CONSTRUCTIONS

NIKHIL CONSTRUCTIONS CO

ask enterprises

G-TECH CONSTRUCTION & FABRICATORS

OM POWER SYSTEMS

MARUTI ENTERPRISES

Vaishnavdevi Furnishers

arcoma