REPAIR MAINT OF FLOORING ROOFS PLUMBING WORKS AT NEW CANTT AND REPAIR MAINT OF INCENRATORS LAUNDARY MH EQPTS EOT CRANE AND STP INCL AMC AND CONNECTED ACCESSORIES AT NEW MIL STN UNDER GE GANGTOK

Amount

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and as directed.

Taking down chowkats or frames exc 1.5 Sqm and n.exc 4 Sqm (without taking off shutter from the frames) and removal from site complete all as specified and as directed.

All as item No 2.00 here-in before but n.exc 1.5 Sqm each complete all as specified and as directed.

Taking down shutters of any description exc 1 Sqm and n.exc 2 Sqm each and removal from site complete all as specified and as directed.

Taking down shutters and refixing in same opening of any description exc 1 Sqm but not exc 2 Sqm each complete all as specified and as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Taking down cement plaster/terrezzo cast in situ of any description on brick or stone wall etc including racking out joints hacking for key scrubbing down with water etc complete all as specified and as directed.

Demolition of concrete in ground floor and pavings n.exc 15cm thick (un reinforced) (below or above ground level) complete all as specified and as directed.

Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Demolition of precast concrete block walling/brick wall built in cement mortar complete all as specified and as directed.

Dismantling old PGI/CGI/AC sheeting any gauge, thickness, including Nainital. Sikkim or similar pattern roof/facia etc complete all as specified and as directed.

M&L for second class hard wood plain solid straight chowkats and frames wrought framed rebated on the solid rounded on chamfered put together with glue pinned and joints complete all as specified and as directed.

M&L for plain, framed, panelled shutters 35 mm thick (any number of panels) , with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers; supplied and fitted to chowkats complete all as specified and as directed.

S&F second class hardwood, glazed and skelton shutters 30 mm thick open rebated and prepared to receive glass, gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part-I Section8, Clause 8.20 (a) supplied and fitted to chowkats complete all as specified and as directed.

S&F factory made flush shutters 30 mm thick, solid core construction, with particle board core commercial type on one side and one face covered with decorative face veneer wtih lipping/frame to match complete all as specified and as directed.

S&F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying & fixing in opening as per specification and drawing complete all as specified and as directed.

S&F of 30mm thick (style thickness) factory made solid panel PVC door shutter consisting of frame made out of mild steel tubes for top and bottom rails, Mild steel frame shall be covered with heat moulded single side prelam PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and single side prelam PVC sheet for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail on either side & as gap insert for toprail and bottom rail, panelling of both side prelam PVC sheet to be fitted in the mild steel frame welded /sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement as per specification and drawing given on MES Schedule Part-II (2020) complete all as pecified and as directed.

S&F 250mm long aluminium anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section complete all as specified and as directed.

M&L for 150 mm size aluminium anodised cast type handles complete all as specified and as directed.

M&L for 100 mm size mild steel pressed handles, oval types, stove enameled black complete all as specified and as directed.

S&F of 150mm long aluminium anodised,barrel tower bolt of extruded section complete all as specified and as directed.

S&F of 100mm long aluminium anodised,barrel tower bolt of extruded section complete all as specified and as directed.

S&F of 100mm size mild steel butt hinges medium weight complete all as specified and as directed.

Supply & fix 100mm size brass handles (decorative type) cast type polished bright complete all as specified and as directed.

S&F of 75mm size mild steel butt hinges medium weight complete all as specified and as directed.

S&F continuous ( piano) hinges with 30 mm width of flaps ( when open), mild steel bright finish or electrogalvanised fixed with stainless steel screws complete all as specified and as directed.

S&F in repairs of 18 / 19mm thick particle board medium density flat pressed,single layer type with BWR type adhesive fixed with screws to timber frame work as in repair including teak wood lipping 6mm thick all round fixed with nails complete all as specified and as directed.

M&L for PCC (1:3:6), type C-1 (using 20mm graded stone aggregate) as in coping complete all as specified & as directed.

S&F in repair 15mm bore long body bib taps one/two way cast copper alloy chromium plated, fancy type with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule & fixed complete all as specified and as directed.

S&F in chromium plated health faucet with 1.25m long flexiable pipe incl fixing to steel pipe 15mm bore or union including ABS wall hook and making connection and fixed in position complete all as secified and as directed.

S&F in repair 15 mm bore chromium plated angular stop cocks with flange complete all as specified and as directed.

Taking up or down 20mm bore steel water tubings and fittings etc complete and making good disturbed surfaces of walls/ceilings or floor etc complete all as specified and as directed.

Taking up or down 25mm bore steel water tubings and fittings etc complete and making good disturbed surfaces of walls/ceilings or floor etc complete all as specified and as directed.

M&L for 25mm steel tubing medium grade,galvanised fitting fixed complete to walls and ceiling or floor complete all as specified and as directed.

All as per item No 34.00 here-in-above but fixing only.

Supplying and laying 20mm bore outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and as directed.

M&L for cutting chases, pinning in, making good to facing where required and pointing in CM 1:3 for concealed water tubing and making good, cutting n.exc 10cm girth as in stone or concrete block walls complete all as specified and as directed.

M&L for glazed coloured ceramic tiles (450x300x7mm thick) on vertical surfaces such as skirting/dado set and jointed in neat cement slurry pointed in white or coloured cement to match the colour incl 10 mm thick screed bed/rendering of CM (1:4) as in wall complete all as specified and as directed.

M&L for Non - skid colured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc.set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 15mm thick screed bed in cement mortar (1:6) for laying floor finishes complete all as specified and as directed.

M&L for machine cut prepolished kota stone flooring slab flooring 20-25mm thick over cement screed 15mm thick screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab complete all as specified and as directed.

M&L for 100 mm thick plain cement concrete (1:2:4) type B-2 (using 40 mm graded stone aggregate) as in hardstanding/flooring and finishing the surface even and fair etc complete all as specified and as directed.

M&L for 75mm thick PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in plinth protection/path etc finishing the surface even & smooth without using extra cement complete all as specified and as directed.

M&L for PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in surface channels/drain including forming fair finished to drain channel complete all as specified and as directed.

M&L for rendering 15 mm thick on fair faces of brick or concrete surfaces in cement mortar (1:6) finished even & smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15mm thick in cement mortar (1:4) in two layers using WPC in finishing layer on brick or concrete surfaces finished even & smooth (WPC for finishing layer will be paid seperately as supply only) complete all as specified and as directed.

M&L for 5mm thick rendering in CM (1:3) in ceiling finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

Supply only liquid water proofing compound complete all as specified and as directed.

M&L for pre-painted galvalume aluminium zinc coating GI based corrugated/ Zigzag/ Trapezoidal pattern corrugations steel sheet 0.50mm thick of an colour having tensile strength of 550 mpa as in roof covering fixed with self tapping screws/L type or J hooks complete all as specified and as directed.

M&L for pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550mpa as in roof covering fixed with self tapping screws /L type or J hooks complete all as specified and as directed.

Hacking out of old broken glass any thickness size quality or description from metal frame including punching or drilling out old glazing pins complete all as specified and as directed.

S&F in repair 4mm (tinted) sheet glass, ordinary quality in squares n exc 0.5 sqm each pane complete all as specified and as directed

S&Fof 3mm thick sheet glass Figured glass, pin head type and glazing with n.exc 0.5sqm each fixed to steel frame complete with oil putty in square including steel pin complete all as specified and as directed.

M&L applying one coat of white washing including preparation of old decorated surface of ceiling complete all as specified and as directed.

M&L for applying two coats of white washing including preparation of new or previously untreated surface of ceiling complete all as specified and as directed.

M&L for applying two coats of white wash including preparation of new or previously untreated surfaces of walls complete all as specified and as directed.

M&L for preparation of old decorated surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soot, mass and efflorescent salts and trading oil and greasy spots and apply one coat of white wash complete all as specified and as directed.

M&L for applying two coats of acrylic emulsion distemper including complete removal of existing treatment on wall complete all as specified and as directed.

M&L for applying wall care putty of 3 mm thick in two layers (1.5mm each layer) complete all as specified and as directed.

M&L for preparation of old plastered surfaces of walls and applying one coat of acrylic emulsion distemper complete all as specified and as directed.

M&L for applying two coats of exterior acrylic emulsion painting (weather coat) over a coat of alkali resistant primer including complete removal of existing treatment and preperation of old/new surfaces all as directed.

M&L for applying one coat of weather shield exterior emulsion paints (weather coat) including preparation of old wall surfaces complete all as specified and as directed.

M&L for two coats of synthetic enamel painting (1st grade in quality) to new steel surface over a coat of red oxide primer including preparation of surfaces area exc 10cm width & girth complete all as specified and as directed.

M&L for prepartation of old painted steel surfaces of any description, over 10 cm width or girth, not otherwise described and apply one coat of synthetic enamel paint (1st grade in quality) complete all as specified and as directed.

M&L for two coats of synthetic enamel painting (1st grade in quality) to new wooden surfaces over a coat of pink primer including preparation of surfaces area exc 10cm width & girth complete all as specified andas directed.

M& L for prepartation of old painted wooden surfaces of any description, over 10 cm width or girth, not otherwise described and apply one coat of synthetic enamel paint (1st grade in quality) complete all as specified and as directed.

S&F in repair Water Closet (squatt pattern) of vitruous china squatting pan of pattern "ORRISA" pattern size 580 x 440 mm white with integral foot rests (excluding flushing cirstern and flush pipe) including connection to trap and flushing pipe anti syphon pipe etc complete including trap set in and incl concrete complete all as specified and as directed.

S&F in repairs of G I steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks,or galvanised wire staples to wooden/steel shutter complete all as specified and as directed.

S&F for Rolled sections Fe 410-w (grade E-250) quality-A as in main and cross beams, hip and jack rafters;purlins where connected to common rafters and running rails and guides for sliding doors;fixed with angle cleats or other connecting plates complete all as specified and as directed.

S&F framed work such as grills, gratings etc, with ends of bars, shoulded and/or riveted or forged in spikes, framed guard bars, walk ways, railings, frame work of water tanks and similar works conforming to Fe 290, Gde-E-165 complete all as specified and as directed.

Dismantling wall and ceiling board (fibre pulp, insulation etc) or insulation boards any thickness including cover fillets complete all as specified and as directed.

Dismantling timber scantling 40 sqcm and over in section and in any position in section complete all as specified and as directed.

M&L 2nd class hard wood as in timber scantling ,clean sawn, and fixed unframed work etc complete all as specified and as directed.

S&F powder coated GI grid frame work for false ceiling comprising of the following sections for making partition of 600x600mm size fixed to walls with rawl plugs and screws and hanged to roof with and including 1.18 mm dia GI wire suspender of suitable length and buterfly clips, size of main tee shall be 23mmx 28mmx 0.30mm thick, cross tee shall be 24x 23x .30 mm thick and wall angle shall be 20mmx20mmx0.30mm thick complete all as specified and as directed.

S&F for 4mm thick Non asbestos fibre cement building board (E-board) of approved texture for insulation and acoustic purpose of size 595x595 mm size fixed with staples on snap grid as in ceiling complete all as specified and as directed.

S&F in repairs Harrison rail,anodised aluminium alloy , 25 mm dia with fixing brackets, stops, rollers, nob, holder etc in curtain rails complete all specified and as directed.

M&L for granite (of any type) work 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite granite stone including cutting and polishing etc including 15mm thick screed bed in CM (1:6) complete all as specified and as directed.

M&L for rounding to edges of granite slabs one edge such as in steps, cooking platforms and other similar situations complete all as specified and as directed.

M&L for formworks to sides and soffit of floor,roof beam, beam haunching, girders, bressummers, lintels, cantiliver shelves including support overhangs etc also splays between floor and beam etc complete all specifed and as directed.

M&L for TMT bars , 10 mm dia and over cut to length, bent to shape required including cranking ,bending spirally, hooping for columns, hookings/ends and binding with and including MS wire not less than 0.9 mm dia or securing with clips complete all specifed and as directed.

All as per item No. 79.00 here-in-above but 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders complete all as specified and as directed.

M &L for RCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in Slabs supported on walls including necessary form work complete all as specified & as directed. NOTE : Re-inforcement shall be measured and paid separately.

M&L for Pre-cast cement concrete (1:3:6) type C1 (20mm graded aggregate) block masonry with Solid blocks, exc 10cm in width and setting in mortar (1:6), complete all as specified and as directed.

Demolition of stone or boulders masonry built in cement mortar including all quoins, arches, pillars, pre-cast PCC bond stones with separating seviceable stones & setting aside for reuse in the work all as complete as specified and as directed.

M&L for stone walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar (1:6) including brought up to courses complete all as specified and as directed.

All as per item No 86.00 here-in-before but except stone. Note:- Stone boulders obtained from item No 83 here-in-before shall be reused.

Hand packing (any thickness) at back of walls over arches etc. and raising (or lowering) to the required level complete all as specified and as directed. NOTE:- Stone boulders obtained from item No 83 here-in-before shall be reused.

E/M Portion: Periodical maintenance of following items of Mechanical laundry at 178 MH complete all as specified and as directed. Items Covered for preventive and breakdown maintenance are :- (i) Industrial Washer extractor Model FWX 30 of 02 Nos (ii) Automatic machine fully automatic Cacity 15 Kg (iii) Industrial Drying Tumbler model DTE35 of 01 Nos (iv) Flat work Ironer Calendering machine Model F15-10 of 01 No (v) Flat bed press model SFESE of 01 No (vi) Vaccume Finishing Table Model FES786 of 01 Nos (vii)Stem Gen set capacity- 10 Kg/Hour of 01 Nos Note :- (i) Quoted rate is exclusive of the cost of the spares used and spares will be measured and paid separately (ii) Quoetd rate is inclusive of T&P and authorised service Engineer. (iii) If any fault/defects will be found during the currency of defects liability period of conract. Contractor will rectified all the fault/defects of his own lost. (iv) Rate quoted includes the cost of the authorised technical visit/carried out pratice maintenance of every month.

Supply only Electric drain valve 3" complete all as specified and as directed.

Supply only Heavy loading spring complete all as specified and as directed.

Supply only L.P. house pipe 3" complete all as specified and as directed.

Supply only S.S house pipe clamp 4 " complete all as specified and as directed.

Supply only electric water inlet valve 2" complete all as specified and as directed.

Supply only door gas kit complete all as specified and as directed.

Supply only M.S. elbow 3'/3" complete all as specified and as directed.

Supply only M.S. pipe 3'/3" complete all as specified and as directed.

Supply only Heater 9 KW existing water extractor and drying tumbler as directed.

Supply only air switch complete all as specified and as directed.

Supply only air connector 8mm/15mm complete all as specified and as directed.

Supply only contactor 40 Amp complete all as specified and as directed.

Supply only air fill bal pipe 3" complete all as specified and as directed.

Supply steel glass wool complete all as specified and as directed.

Supply only V belt of Cat No :AX60LP039 B-124 for Industrial washer extrator model FWX 30 complete all as specified and as directed.

Supply only 3 way Water Solenoid Valve for Industrial washer extrator model FWX 30 complete all as specified and as as directed.

Supply only Door gasket for Industrial washer extrator model FWX 30 complete all as specified and as directed.

Supply only Hose pipe for drain-Straight for Industrial washer extrator model FWX 30 complete all as specified and as directed.

Supply only bearing for electric motor for Industrial washer extrator model FWX 30 complete all as specified and as directed.

Supply only Limit Switch for drain-Straight for Industrial washer extrator model FWX 30 complete all as specified and as directed.

Supply only Hose Clamp for Industrial washer extrator model FWX 30 complete all as specified and as directed.

Supply only water inlet pipe for Industrial washer extrator model FWX 30 complete all as specified and as directed.

Supply only rectifier unit for Industrial washer extrator model FWX 30 complete all as specified and as directed.

Supply only V belt for Flat work Drying Ironer Model FS 53-300 complete all as specified and as directed.

Supply only contactor for Flat work Drying Ironer Model F15-10 complete all as specified and as directed.

Supply only Thermocouple j type 3Mt Length for Flat work Drying Ironer Model F15-10 complete all as specified and as directed.

Supply only Conveyar belts for Flat work Drying Ironer Model F15-10 complete all as specified and as directed.

Supply only Digital timer for Flat bed press model SFESE complete all as specified and as directed.

Supply only Teflon Sheet For Head for Flat bed press model SFESE complete all as specified and as directed.

Supply only Kit for Pneumatic Cylinder For Head for Flat bed press model SFESE complete all as specified and as directed.

Supply only Heater for Iron For Flat work Ironer Calendering machine Model F15 complete all as specified and as directed.

S & F in repair water solenoid valve 1.5" for FWX 30 part no. AX60FR026 complete all as specified and as directed.

Supply and fix in repair of Display control unit microprocessor based computer control functioning unit, LCD with touch functionality, 415 main voltage, 3 phase, AC supply, calliberating and programming to operate the washing machine/industrial dry Clean Machine/Industrial Washer extractor/ Industrial Drying Tumbler and providing smooth operation to the system, along with all necessary wiring etc all complete as specified and as directed.

Repair of existing display control unit microprocessor based computer control functioning unit, LCD with touch functionality, 415 main voltage, 3 phase, AC supply, calliberating and programming to operate the washing machine/industrial dry Clean Machine/Industrial Washer extractor/ Industrial Drying Tumbler and providing smooth operation to the system, along with all necessary wiring etc all complete as specified and as directed.

Supply and fix in repair of double function type bearing for washer extractor or drying tumbler of capacity of 60 KG including all fitting and fixture washer nut, bolts complete all as specified and as directed.

Supply and fix in repair of Vibrator bush as per existing sample complete all as specified and as directed.

M & L for cleaning of air compressor Machine air line and air storage tank as per existing sample complete all as specified and as directed.

Supply and fix in repair of automatic pressure release valve as per existing sample complete all as specified and as directed.

Supply and fix in repair of air filter for compressor as per existing sample complete all as specified and as directed.

Supply and replacement of air compressor Belt as per existing sample complete all as specified and as directed.

Supply only NO/NC / 2 Emergency Stop for water extractor and drying tumbler complete all as specified and as directed.

M& L for servcing of pump sets 7.5 HP capacity the pump sets by repalcing the worn out bushes, mechanical shaft seal, gland bolts & nuts, etc including testing and commissioning complete all as specified and as directed by Engineer-in-Charge.

Material and labour for periodical maint of oil fired incinerator with rotary scrubbing system burning capacity 55 to 65 KG/Hr comprising of primary and secondary chamber which includes the following works :- (a) Descalling of Gap between greades (b) Descalling of combution chamber (c) Descalling of arch chamber (d) Descalling of stack arrester. (e) Overhauling burner nozzel blast tube pump, diffuser etc. (f) Cleaning of Diesel tank and fuel lines. Note :- (i) Rate includes for painting on Diesel Tank and writing in White Paint Date of cleaning and capacity. (ii) Contractor shall be liable to provice OEM technician as and when required for trouble shooting of incinerator during the currency of defect liability period. (iii) Rate quoted includes the cost of the authorised technical visit/carried out pratice maintenance of every month.

M&L for strip opening of primary chamber and removal of the ashes or any dust materials from inside with restoring of all calicum silicate insulation and welding of steel plates and its bracing and stiffening, complete repair to the refractory lining of the chamber and providing of ceramic wool for flanges and expansion joints, settings of dismantled insulation bricks and providing heat resistant aluminium painting complete all as specified and as directed.

M&L for strip opening of the secondry chamber and removal of the ashes or any dust materials from inside with restoring of all calicum silicate insulation and welding of steel plates and its bracing and stiffening, complete repair to the refractory lining of the chamber and providing of ceramic wool for flanges and expansion joints, settings of dismantled insulation bricks and providing heat resistant aluminium painting complete all as specified and as directed.

Material and labour for complete servicing of fire burner pump complete all as specified and as directed.

Supply and fix in replacement of burner of 30 A for complete of fire burner pump complete all as specified and as directed. Make- Bentone cat part No. B 30A

Material and labour for De-silting & cleaning of sewage treatment plant sump complete with taking out water mixed with bleaching powder, sludge & solid sludge etc removing and depositing out of cantt area in a covered container and servicing STP plant for proper functioning of STP all as specfieid and as directed. Note :- The cleaning of the following pit, chamber, sump and drain :- (a) Coarse bar screen pit - 01 No (b) Receiving sump - 01 No (c) Stiling chamber - 02 Nos. (d) Fine bar screen pit - 02 Nos (e) Main out going drain of length 50 Mtr. Note-(i) New filter media will be measured and paid separately under relevant itemsof BOQ (ii) Contractor shall be liable to provice OEM technician and when required for trouble shooting of STP during the currency of defect liability period. (iii) Rate quoted includes the cost of the authorised technical visit/carried out pratice maintenance of every month.

Supply only aggregate filter media for STP sludge drying bed(as per existing) of size 1/8 to 1/16,1/16 to 1/32 inch size compete in layers as per existing sample complete all as specified and as directed by engr-in-charge.

Suppying only alam cleaning of treated water complete all as specified and as directed.

M& L for taking out existing type pumpset/airblower/Induction motor of 1.5 HP capacity for servcing by disconnecting motor,blower,,pipe line and removing of all aprts like bearing,bushes,imleller,shaft etc cleaning all surface and scales/sluged/dirt/formed inside/outside pumpset/blower etc lubricating/greasing at proper places and refixing in position with all serviceable parts with motor incl painting with one coat of anti corrosive paint over red oxide primer and testing and commissioning all as directed by Engr-in-Charge.(Note spares like bearing,winding will be measured and paid seperately)

All as per item No. 141.00 here-in-above but 2.0 HP capacity.

All as per item No. 141.00 here-in-above but 5.0 HP capacity

Suppy only ball bearing for 1.5 HP capacity of pumpset/airblower/motor

All as per item No. 144.00 here-in-above but 2.0 HP capacity.

All as per item No. 144.00 here-in-above but 5.0 HP capacity.

M& L for taking out existing type air compressor of 40 Cum/hr capacity for servcing by disconnecting motor,blower,,pipe line and removing of all aprts like bearing,bushes,imleller,shaft etc cleaning all surface and scales/sluged/dirt/formed inside/outside pumpset/blower etc lubricating/greasing at proper places and refixing in position with all serviceable parts with motor incl painting with one coat of anti corrosive paint over red oxide primer and testing and commissioning all as directed by Engr-in-Charge.

S&F Temperature controlling relay 110-240V, AC phase, Siemens of Cat no - 7UG0480-1IU20 or its equivalent in ABB, L&T complete all as specified and as directed.

Repairs/Servcing to EOT of 2.0 Ton capacity by replacingu unserviceable gear box oil and filling new oil, greasing the moving parts, chain etc, removing u/s chain pulley auto limit cut off switch, button box and copper cable from ground to EOT and fixing seviceable cable and switch box, repairs to EOT panel by replacing contactors and limit switches complete including painting with two coats of existing colour for complete EOT complete all as specified and as directed. Note- (i) Contractor shall be liable to provice OEM technician as and when required for trouble shooting of EOT crane during period of contract (ii) Spares parts shall be measured and paid seperately under respective item.

Supply, fixing, testing and commissioning of VVVF drive for heavy duty cranes with required resistance, power and control cables, cable lugs for fixing of drive/ Conventional Panels suitable for CT and LT work on Main Hoist Operation on three phase 415Vac from 3 KW including programming all the paramaeters as rquired by the ground /existing condition for capacity EOT cranes complete by removing the old defective drive /conventional system all as specified and directed. Make: Yaskawa, model No. CIMR-VT4A0007BAA or equivalent model of mater /Thosiba/Simens/ABB/L&T

Supply only wire rope embeded pendant cable including necessary fittings and fixture acomplete all as specified and as directed by engr-in-Charge.

Material and labour for rewinding of motor of capacity of 3.0 KW for Crane as per eixsting copper gauge and testing complete all as specified and as directed.

Supply and fixing in repairs to rope drum including necessary fittings and fixture complete all as specified and as directed. by engr-in-charge

Supply only Push button station 12 way made out Alu dia Cast housing with push button element/light

Supply of Rotary Type Geard Limit Switch Ratio 48:1 With 4 Contact Type GRLS /48/4SE complete all as specified and as directed.

Supply of Two Way Lever Type Limit Switch 2 Contact Type LS/2SH/2 in LPS4 Enclosure complete all as specified and as directed.

Supply of PVC Insulated Shrouded G.I. Busbar System 100Amp. “ W” Type ( R, Y ,B G ) 4 Bar With Jointer , Joint Cover , Hanger Clamp , Anchor Clamp , End Power Feed , & End Cap complete all as specified and as directed.

Supply only Current Collector 100Amp. Type “W” Make NBM Safe line , Speedage complete all as specified and as directed.

Supply Busbar Mounting Bracket Size 35X 35 X 5 , 400MM (Single Slotted 10 x 138 ) complete all as specified and as directed.

Supply PVC Insulated & PVC Sheathed Bright Armored Copper Conductor Flexible Cable 1.5Sqmm 16Core. Voltage Grade1100V as per IS 694/1990 complete all as specified and as directed.

Supply only PVC Insulated & PVC Sheathed Bright Armored Copper Conductor Flexible Cable 1.5Sqmm 3Core Voltage Grade 1100V as per IS 694/1990 complete all as specified and as directed.

Supply PVC Insulated & PVC Sheathed Bright Armored Copper Conductor Flexible Cable 2.5Sqmm 3Core Voltage Grade 1100V as per IS 694/1990 complete all as specified and as directed.

Supply PVC Insulated & PVC Sheathed Bright Armored Copper Conductor Flexible Cable 4Sqmm 3Core Voltage Grade 1100V as per IS 694/1990 complete all as specified and as directed.

Supply Cable Trolley Single Wheel Type with Cable Holding Clamp complete all as specified and as directed.

Supply of Electronic Rectifire 415V AC / 190V DC ( 1 Input 415V AC & Output 190V DC ) complete all as specified and as directed.

Supply Disc type DC Brake 415/190V. DC complete all as specified and as directed.

Water testing of samples of STP (New Cantt) for (A) Physical, Chemical & Bacteriological Charecteristics of water (B) General parameters concerning physical - 11 parameters (i) pH Value Total dissolved solids (TDS) (iii) Total suspended solids (TSS) (iv) Ammonical Nitrogen as NH3 (v) Dissolved Oxygen (DO) (vi) Biochemical Oxygen Demand (BOD) (3 days at 27 deg Celcius) (vii) Chemical Oxygen Demand (COD) (viii) Oil & Grease (ix) Total Kjeldahl Nitrogen (x) Faecal Coliforms (xi) Fluoride. ( 1 sample per quarter) complete all as specified and as directed.

M/S S. S CHETTRI AND SONS

KAMLESH ENTERPRISE

M/S ANIL KUMAR THAKUR

BIJAY MITTAL

RAAJ BANGAR

KARMA TSETEN BHUTIA

MAHENDRA KHAWAS