ADDITION/ALTERATION TO DRAIN, PATH AND ALLIED WORKS NEAR GUARD POST NO 07 AT INS UTKROSH AND CERTAIN SANCTIONED WORKS UNDER GE MINNIEBAY, PORT BLAIR

Amount

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering

Dismantling wrought iron or mild steel work of any description not otherwise provided for

Excavating in post holes for Hard and dense soil (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm

M&L cement concrete1:3:6 type D2 using 40mm graded stone aggregate in foundations fillings and mass concrete

Material and labour for steel work in tubular trusses including special shaped washers etc complete using ERW or induction but welded tubes conforming to IS 1161-1979 grade SI-240 complete all as specified and as directed. .

Supply and fix Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and as directed. Note:-(i) End laps not less than 25cm and side lap at least one corrugation, Mastic lapping tape is to be provided at the laps and stitching screws should be provided at the side lap & end laps at interval of 600mm, eaves filler strip to be bonded to the valleys or pans with flexible water proof silicon sealant. Self tapping screw 65mm long and 32mm long is to be provided at crest and valleys respectively. (ii) Unit rate is deemed to be inclusive of sealant .

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges, facia & valley gutter and similar work

S & F Aluminium flat iron work in, wind ties screwed as directed, including all necessary drilling, bolting or riveting etc., and similar work

M&L Plates (plain or chequered) channels. Square cut or notched (ordinary and counter sunk) forming holes, without any attachment

Material and Labour for preparing new steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles

M&L Pre-cast cement concrete block masonry with solid blocks type C1 1:3:6 using 20 mm graded aggregate, exc. 10 cm in width and setting in cement mortar 1:6, complete

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.

M&L RCC M30 grade (Design Mix) using 20mm graded stone aggregate as in lintel, beams etc.

M&L TMT steel bars 10mm dia and over cut to length bent to shape required incl cranking bending spirally for hooping for columns, hooking ends and binding with and incl MS wire (annealed) not less than 0.9mm dia or securing with clips

-Ditto- but 6mm to 8mm

-Ditto- but 5mm dia & over upto and incl 10mm dia in stirrups, spacers and binders

M&L Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre /intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended fr soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (n.exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 400 mm centre to centre.

M & L for preparing Ceiling surfaces and applying 3mm thk wall care putty coats of Cement based Wall Care Putty of make JK / Birla / Jenson & Nicholson / Altec on Ceiling including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of oil bound distemper over one coat of alkaline resistance primer complete all as specified and as directed.

M & L Non asbestos fibre cement building boards 6 mm thick fixed or laid/ inserted to timber/GI/Aluminium framework.complete all as specified.

M&L Hangers 4 mm dia. G.I. (upto1200mm length) adjusting levelfixed to roof slabs by means ofceilling cleats made out of G.I.flat 40 x 3 mm size 60mm longand expansion hold fasteners12.5mm dia. 40mm longcomplete all as specified

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

M&L rendering 10mm thick in CM (1:6) on wall surfaces finished even & smooth without using extra cement.

M&L for rendering 15mm thick cement plaster on fair faces of concrete block masnory in two layers, base layer 10mm thick in CM (1:6) and top layer 5mm thick in CM 1:4(with river sand) mixed with WPC as per manufacture' s instructions, finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. Note :- WPC shall be measured and paid seperately

Supply only water proofing compound

M&L preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over a coat of primer all as specified.

M & L for preparation of new plastered or previously untreated wall surfaces including scraping, rubbing and washing etc and applying two coats of acrylic emulsion based premium quality matt finish exterior antifungal paint over a coat of primer in chequrred pattern all as directed by the Engineer-in-charge and as per manufacturers instructions

S&F in repairs Anodised Aluminium frames for Partition, Door, Windows and Ventilators with one or more rebates incl jointing cleat for fixing etc and aluminium anodised skelton windows & ventilator shutter fixed with gauge, side hung type without sash bars using standard aluminium section incl necessary Aluminium grill, jointing cleats, glazing clips, rubber packing anodised aluminium snap beadings screws, anodised aluminium fittings such as handles stainless steel adjustable friction stay hinges etc complete all as specified incl aluminium grills fixed to window frame aluminium anodised wire cloth fixed to aluminium frame all as specified and directed NOTE: (i) Payment under this item will be make only for the cost of aluminium section. However unit rate quoted shall deemed to include cost of rubber beading, fittings such as handles, SS friction stay hinges (ii) Weight of aluminium handle & SS hinges shall not be accounted for payment purpose .

Supply and Fixing 5mm Plain glass ordinary quality ,in square exc0.5 sqm each.

Demolition floor, hearth or wall tiling including cement mortar bedding and rubbished off the premises all as specified and directed.

Demolition Of unreinforced cement concrete in any position all as directed

M&L for 75mm thk PCC 1:5:10 typeE2 ( 40 mm graded aggreage ) sub base

M&L for 25mm thick PCC 1:2:4 type B0, (12.5mm graded aggregate) as in subase to flooring.

M&L for coloured non-skid ceramic tiles 7 to 8 mm thick exc. 0.11 sqm but n.exc 0.18sqm area of each tiles in floor/ steps etc set and jointed in neat cement slurry and pointed in coloured cement to match as in floor over and including 15mm thick screed bed in CM (1:6)

M&L for glazed ceramic tiles 450x350x 7mm thick in vertical surface set and jointed in neat cement slurry and pointed in white or colour cement to match over 10mm thick backing in cement mortar (1:3) all as specified and directed

S&F in repairs vitreous china wash down water closet pan pedastel pattern of size710x370x810mm (EWC)(couple Closet) white in colour with and incl Soft close Seat cover white closed pattern with flat bottom ,Twin flush fittings and cover and MS chromium plated hinging device incl connection to outgoing pipe and flushing pipe complete.

S&F in repairs brass chromium plated telescopic Hand shower(Health Faucet)(ABS Body) with 1 Meter long Easy Flex Tube in Chrome Finish& wall Hook all as specified Make:Prayag Cat No:BEA-87 or equivalent make mentioned in PS.

S&F in repairs cabinet mirror of over all size 550 x 520mm x 100mm incl necessary partition etc.

S&F in repairs Swivel Towel Holder Twin Type CP Brass all as specified.

S&F in repairs Towel Rack 600mm Long with Lower Hangers Superior finished CP Brass all as specified.

S&F in repairs Shower Basket Large Superior finished CP Brass all as specified.

S&F in repairs brass chromium plated shower rose with or without swivel joint 125mm size.

S&F in repair Corner glass shelf high quality of 5mm thick glass & CP railing with bracket. (Make : Cat No ACN-1173 of Jaquar/272130160031 of Somany or equivalent make mentioned in PS.

S&F in repairs Anglur stop cock cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for pipe or union fixed for 15mm bore).

S&F in repairs stop valves cast copper alloy chromium plated with long shank and cup (concealed type) fancy type screwed down high pressure screwed both ends for pipe or union fixed for 15mm bore,including necessary cutting and making good wall or floor tiling to match existing surface complete all as specified and directed.

S&F in repairs vitreous china wash basin, white flat back of size(mm)160x600x470 with half pedestal excluding tap incl bracket complete all as specified and as directed.

S&F in repairs Pillar taps, cast copper alloy chromium plated, fancy type, screwed down, high pressure with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nut of 15mm bore. Make:

S&F in repairs bib tap cast copper alloy fancy type chromium plated screwed for 15mm bore of approved. Make:

S&F in repairs Single Towel Rail 600mm long Superior finished CP Brass all as specified.

S&F in repairs 2 in one bib tap cast copper alloy fancy type chromium plated screwed for 15mm bore of approved. .

Taking 20mm down Steel/CPVC tubing and connections including cleaning for refixing or removal to store.

Taking 25mm down Steel/CPVC tubing and connections including cleaning for refixing or removal to store.

Supply and laying of CPVC pipes 20 mm dia outer boreSDR 11 &plain CPVC SDR 11 fittings/special fittings on walls /ceilings or laying in floors complete all as specified.

Supply and laying of CPVC pipes 25mm dia outer boreSDR 11 &plain CPVC SDR 11 fittings/special fittings on walls /ceilings or laying in floors complete all as specified.

S&F in repairs gun metal gate valves with iron wheel head screwed both ends for iron pipe of dia 25mm.

S&F Ball brass valve high pressure of polyethylene float and fly nut complete screwed for iron pipe and fixed, cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed of 25mm bore.

Supply and fixing 20 mm outer dia CPVC pipes brass Elbow

Supply and fixing 20mm outer dia CPVC pipes brass Elbow(3/4 X1/2)

Supply and fixing 20mm outer dia CPVC female brass adoptor(FTA/FBTA)

Supply and fixing 25 mm outer dia CPVC female brass adoptor(FTA/FBTA)

Supply and fixing 20 mm outer dia Brass Tee

Supply and fixing 25 mm outer dia tank Adaptor

Supply and fix Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 1000 ltrs capacity hoisted and fixed in position all as specified in SSR Part I including Dismantling and removing to where directed

Demolition and breaking out drain pipes of any dia including necessary bend ,T and other accssories. Etc

Taking down PVC SWR pipes including fittings and fixture any dia from walls/floors

S & F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls incuding necessary clamps etc to fixing on walls all as specified.

S & F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid intrenches or in floors incuding necessary clamps etc all as specified.

S & F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid intrenches or in floors

S & F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls incuding necessary clamps etc to fixing on walls all as specified.

S & F 110 mm bore PVC (SWR) bends of any radius including jointing with solvent cement complete.

S & F 110 mm bore PVC (SWR) junction single (Single `T') equal or unequal with access door.

S & F 110 mm bore PVC (SWR) Vent Cowl

S & F 75 mm bore PVC (SWR) bends of any radius.

S & F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal with access door.

S & F 110 mm bore PVC (SWR) bends with access door

S & F 75 mm bore PVC (SWR) branch piece,double(double Y) equal or unequal

S&F PVC SWR reducers one end 110 another reduced 75mm

S&F in repairs PVC (SWR) floor trap diameter of out let 75mm ,plain with grating including jointing with solvent cement fixed in cement concrete all as specified and directed ,(cement concrete shall be measured and paid seperately.

Taking down chowkats or frames not exceeding 1.5 Sqm (with shutters &grill(if fixed) without taking off shutters from the frame).

Taking down chowkats or frames exc 1.5 Sqm and not exceeding 4 Sqm (with shutters and grill (if fixed) without taking off shutters from the frame)

S&F Factory made solid panel PVC door shutter 30 mm thick (Rudraksh style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing

M&L solid PVC(Rudraksh) Door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling & fixing in opening as per specification & drawing.

Material and Labour for hard core of gauge n,exc 63mm of broken stone, deposited , spread and levelled in layers n,exc 15cm thick, watered and rammed to a true surface complete all as specified and as directed.

Material and Labour for 75 mm thick, PCC 1:3:6 type C1, using 20mm graded stone aggregate laid in panels surface finish even and smooth without using extra cement as in plinth protection complete all as specified and as directed.

M&L for PCC (1:4:8) type D2 (using 40mm graded aggregate) 100 mm thick all as specified and directed

M&L for chequered cement tiles 10mm thick (square/rectangular) polished heavy duty vertified tiles 300x300 size infloors etc,set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 20 mm thick screedbed in CM ( 1:6) complete all as specified and directed.

Excavating in trenches n.exc.1.5m wide and n.exc.1.5m in depth for fdn of walls and n.exc.10sqm on plan and getting out in any type of soil

Excavating in trenches exc.1.5m deep and n.exc.3m in depth for fdn of walls and n.exc.10sqm on plan and getting out in any type of soil

M&L PCC 1:4:8 type D2 using 40mm graded stone aggregate in fdn filling and mass concrete

M&L PCC 1:2:4 type B1 (using 20mm graded stone aggregate) 70mm thick finished even and smooth using extra cement

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in hard dense soil

Removing excavated soil to a dist n.exc. 50m and depositing where directed at a level n.exc.1.5m above the starting point

M&L for rendering 15mm thick plaster in CM (1:4) on brick/block wall or concrete surfaces finished even & fair all as specified and as directed.

Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165

M&L for Mild steel, plain, black sheet in wall cladding of 1.25mm thick , steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required

M&L providing precast RCC 1:2:4 type B-1 (using 20 mm graded stone aggregates) as in slabs, chullah hoods, chajjas, water troughs, shelves and similar articles including cost of necessary form work.

M&L for applying two coat of acrylic emulsion weather coat premium quality antifungal exterior emulsion to newly plastered surface of wall over a coat of primer including preparation all as specified and directed

M&L for applying two coat of acrylic emulsion weather coat premium quality antifungal exterior emulsion to old painted surface of wall including preparation all as specified and directed

M&L for applying one coat of acrylic emulsion weather coat premium quality antifungal exterior emulsion to old painted surface of wall including preparation all as specified and directed

M & L for cleaning the exting floor / Concrete surfaces/Path by washing rubbing etc to remove caked mud/ grease etc and applying high pressure wall jet of 120 PSI or move for obtaining a clean surfaces free from algac/organic particles and applying one coat of weather resistant floor paint of Make - Indigo or equivalent

Taking down carefully loose and broken concrete by chiselling/picking etc upto a depth of 80 tor 100mm from columns, beams and similar structural members, cutting edges, cleaning the surfaces so obtained after removing loose and broken concrete with wire brushes etc to remove dust, dirt and other foreign particles etc and washing with clean water with pressure and removal of debries to a distance not exc 50 m including necessary scaffolding etc., complete all as specified and as directed.

M & L for applying one coat of anti corrosive primer @0.25 Ltr/Sqm to exposed surfaces of old and new reinforcement to the full circumfrance and length of bars to form unbroken 40 Micron thick film as per manufacturer's instructions complete all as specified and as directed.

M &L for applying one coat epoxy bonding agent @ 1 ltr/2.6 Sqm or as per manufacturer's instructions to old concrete surfaces of RCC floors, columns, beams and similar structural members for bonding with new concrete complete all as specified and directed.

M & L for non shrink, cementitous micro concrete (Renderoc RG of Fosroc or equivalent) mixed with 12.5 graded stone aggregate by weight (18 Kg Aggregate 25 Kg Renderoc RG) respectively (as per manufacturer's instruction) laid in average thickness 80 to 100 mm in surfaces of columns, beams and similar structural members including use and waster of water tight form work to facilitate pouring of micro concrete complete all as specified and as directed.

Demolition of RCC of any description and in any position not otherwise specifically provided for

M&L RCC 1:2:4 type B1 as in chullah hoods; stairways including steps (square or spandril) any section straight or winding and similar work all as specidied

M&L for drilling 6mm dia holes at a downward/horizontal angle of 45 degree at 150mm centre to centre at junction of floor and wall or contact and wood work or similar affected area and filling ATT solution @ 0.5 litre/hole and sealing the same with gray or white cement as required.

Surface dressing n.exc 15 cm deep and getting out soft and loose soil

M&L 50mm thick PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in sub base of floor complete all as specified and directed

M & L For coloured chequered cement concrete tiles 30 cm x 30cm x 25 mm thick, set and jointed neat cement slurry and pointed with coloured or grey cement match with pigment, over and including 20 mm thick screed bed or bedding layer in cm 1:6 etc. complete all as specified and directed.

M&L for laying 60mm thick precast concrete interlocking coloured, reflective & decorative paver bolcks any shape and size confirming to IS 15658-2006, M-35 Grade over including 50mm thick crushed stone sand cushioning duly water, level and compacted.

M&L for providing PCC 1:2:4 type B1 using 20mm graded aggr as in roof kerbs, mud stops and similar works, rounded or chemferred on edges all as specified and directed. Note:- Quoted rate includes use of form work.

M&L for providing cement concrete type B-1, 1:2:4 (using 20mm graded aggregate) as in coping, benching, and similar works slightly rounded or chamfered angles and throating including necessary form work as directed

M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggr) in surface channels and drains finished even and smooth using extra cement

Extra for forming fair finished drain or channel n.exc 60cm inner girth in CM, using extra cement incl forms, moulds etc

M&L for applying two coats of cement based paint over a coat of chalk whitning on newly plastered surface of wall including preparation complete all as specified and as directed.

E/M Works

S&F in replacement of Load line DB's with provn of double door arrangement made out of CRCA mild steel sheet with insulating material like polyester epoxy powder quoted surface mounting 12 way TPN 415 volts vertical type suitable for MCB's and MCCB's including one No MCCB 250 Amps 4 Pole 36 KA for incoming and 6 Nos MCB TP 63 Amps for outgoing

Suppy & laying and testing cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 Sqmm 3.5 core, laid in duct / fixed on wall/trenches

Suppy & laying and testing cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 95 Sqmm 3.5 core, laid in duct / fixed on wall/trenches

Suppy & laying and testing cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 185 Sqmm 3.5 core, laid in duct / fixed on wall/trenches

Suppy & laying and testing cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 240 Sqmm 3.5 core, laid in duct / fixed on wall/trenches

Design, Supply, installing testing and commissioning factory fabricated out door type totally enclosed LT cubical panel board CPRI approved suitable size with busbar, conforming to relevant IS and protection class IP-65 ,dust,vermin and weather proof fabricated out of 3.15mm thick CRCA sheet duly powder coated ,mounted on 40x40x5mm MS angle iron frame,duly welded in shape and coated with two coats of synthetic enamel paint of approved colour over a coat of redoxide primer including necessary grouting of legs 300mm deep in ground in PCC 1:4:8 type D2 using 40mm graded stone aggregate ,panel base to be 500mm above ground level with suitable compartments for controls and Monitors including cable glands for incoming and outgoing cables,locking arrangement,including accomodating, supply and fixing the following accessories/items including necessary internal panel wiring with suitable size of Copper wire PVC insulated & sheathed multi stranded complete all as specified and as directed by Engr-in-charge.including Supply and fixing the following :-

Supply, laying of Telerex DWC (double Wall corrugated) HDPE pipe ISI marked of outer dia of 160mm and inner dia 136mm polethylene including couplers, bends, cap etc., with smooth internal and profiled external surface for non pressure under ground cable complete all as secified.

Supply & fixing MCCB 4 pole 400 Amps 25 KA capacity 415 V, 50 Hz AC with sheet metal enclosure Complete all as directed.

M/L for sub main wiring with four runs of single core 6.0Sq mm Flame retardant PVC insulated unsheathed multi stranded copper conductor 1100 V grade with colour code and one run of 4.0 Sq mm single core Flame retardant PVC insulated unsheathed multi stranded copper conductor green colour cable as earth continuity conductor drawn in & including PVC conduit/casing & caping all as directed and specified . ( Note:- Two runs of 6.0 Sqmm copper cable,one run of earth wire 4.0 Sqmm copper cable including PVC casing & caping shall be measured & paid as one length )

Design, Supply, installing testing and commissioning factory fabricated out door type totally enclosed LT cubical panel board CPRI approved suitable size with busbar, conforming to relevant IS and protection class IP-65 ,dust,vermin and weather proof fabricated out of 3.15mm thick CRCA sheet duly powder coated ,mounted on 40x40x5mm MS angle iron frame,duly welded in shape and coated with two coats of synthetic enamel paint of approved colour over a coat of redoxide primer including necessary grouting of legs 300mm deep in ground in PCC 1:4:8 type D2 using 40mm graded stone aggregate ,panel base to be 500mm above ground level with suitable compartments for controls and Monitors including cable glands for incoming and outgoing cables,locking arrangement,including accomodating, supply and fixing the following accessories/items including necessary internal panel wiring with suitable size of Copper wire PVC insulated & sheathed multi stranded complete all as specified and as directed by Engr-in-charge.including Supply and fixing the following :-

Supply and fix Triple pole and earth sheet metal encolsure with a three pin and earth plug with socket complete with one triple pole MCB TPN 32 Amps complete all as directed.

Supply and fix Triple pole and earth sheet metal encolsure with a three pin and earth plug with socket complete with one triple pole MCB TPN 63 Amps complete all as directed.

Material and labour for earthing complete with Glavnised iron plate 60x60 cm x 6 mm thick electrode buried directly in ground (earth pit no less than 2.25 Mtrs deep below ground level) with top edge of the plate not less than 1.5 Mtrs below normal ground level connected to glavnasied earth strip 25×4mm earthing lead by means of bolts, nuts, check nuts and washers all as shown in electrical plate no. 5 connected to earth test point and provn of GI pipe 20 mm dia medium grade for watering, GI pipe 15 mm dia light grade for earth wire protection all as specified and including excavation, earth work provn of earth pit, pit cover, CI funnel, wire mesh etc complete and testing on completion.

Note:- (i) The successful contractor after acceptance and prior to commencement of work shall produce valid electrical license issued by concerned State Government/ Union Territory in the name of the contractor or copy of agreement with any other agency having valid Electrical License issued by concerned State Government/ Union Territory along with copy of that agency's electrical license to this office with copy of HQ CWE, Port Blair. (ii) The contractor shall also produce the competency certificate issued by concerned State Government/ Union Territory of the supervisor employed to supervise the electrical works. (iii) The contractor shall also produce necessary permit issued by concerned State Government/ Union Territory of the workers/ tradesmen employed for executing the electrical works.

M/s Balaji Enterprises

Kathir Marketing Services

RAINBOW INTERNATIONAL

bansal construction