Construction of Forest Guard Hut, At Kanda Beat, Block Forest Kanda, Kanda Range under Chopal Forest Division

Excavation in foundations, trenches etc., in earth work, lift upto 1.50m stacking the excavated soil not more than 3m clear form the edge of the excavation and then returning the stacking soil in 15cm layers, when required in to plinths sides of foundations etc. consolidating each deposited layer by ramming and watering and then deposing of all surplus excavated earth as directed with in a lead of 20m

Stone soling properly hand packed filling and consolidation with proper road roller to the required grade and camber i/c spreading watering and rolling of binding material murum & earth etc. B above 100 mm thick

Providing and laying cement 1:6:12 ( 1 Cement 6 Sand 12 graded stone aggregate 40mm nominal size) and curring complete excluding cost of centring and shuttering in

Random rubble masonry/polygonal rubble masonary /polygonal rubble masonary (uncoursed/brought to courses) with hard stone of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (1 cement 6 sand 12 graded stone aggregate 20mm nominal size) at plinth level in

Providing form work of ordinary timber planking so as to give a rough finish including centring, shuttering strutting and propping etc. height of propping and centring below supporting floor to ceiling not exceeding 4m and removal of the same for insitu reinforced concrete and plain concrete work in

P/L in R.C.C. work 1:2:4 ( 1 cement 2 sand 4 stone balast 20mm nominal size i/c curring complete excluding cost of form work & reinforcement upto floor two level

Mild steel / tor steels rein-forcment for r.c.c. work i/c bending and binding placing and position complete upto floor two level

Brick masonry in cement mortar 1:6 in structure upto 3mtrs. Height from plinth level i/c curing complete

Half Brick Masonary in 1:4 (1 cement 4 sand ) cement mortar upto floor two level i/c curing complete

Steel work welded in built up section trusses & framed work i/c cutting hoisting fixing in position and applying a priming court of red lead in beams joists channela angles tee flat with connecting plates oe angle cleats as in main and cross beams hip & jack rafter purlins connecting to common rafter

P/F Partical board ceiling of approved quality with butt jointing & nails framed work & cover fillets to the measured & paid sepretely 8mm thick

P/F Wooden Moulded beading To Door And Window Frames with iron screw ,plugs and priming coat on uneexposed surface etc complete

P/F 0.6mm thick prepainted sheets fixed with G or L hooks 10mm dia G.I. limpet & bitumen washers complete

Making and fixing of ridges or hips 60 cm sheets 0.6mm fixed with G.I.J. hooks 10mm dia G.I. limpet & bitumen Washers complete

Providing and fixing 15 cm. wide 45 cm. overall semicircular plain G.I. sheetgutter with ironbrackets 40x3mm size bolts and nuts and washers etc. including making necessary conections with rain water pipe complete as per design. (Gutter)

Providing and fixing on wall face PVC d-Plast rain water pipes down pipe

P/F on wall faces PVC for rain water pipes i/c filling the joints Accessries PVC plain bend - PVC Plain Bend 110mm dia

75mm dia

Providing and fixing oxidized M.S. spring hinges necessary screws etc. 150mm

Providing and fixing M.S. pressed butt hings with necessary screws - Door 100x58x1.90mm

Window 75x47x1.70mm

Cup board

Providing 40x3 mm flat iron hold fast 40cm long i/c fixing to frame with 10cm diameter bolts 7 nuts and wooden plugs and embending in cc block 30x10x15cm 1:3:6 (1cement 3 sand 6 graded stone aggregate 20mm nominal size

P/F 100mm bright finished brass floor door stopper with rubber cusion secrew etc.

Providing Wood work in frames of doors windows clere shtory windows and other frams wrought, framed and fixed in position in Ist class deodar wood

Providing and fixing ply wood lining with butt jointing and nails (frame work and cove fillets to be measured and paid for separately) 6mm

Providing & fixing 25 mm thick water proof commercial board in shelves/box for cup board with butt joints & nails & fixed Complete.

Providing and fixing 25mm thick water proof commercial board in shutters i/c Carriage of materials

P/F Marble stone on kitchen shelf

Providing & fixing decorative high pressure laminated sheet of plain /woood grain in gloss /matt /sued finshed with high density protective surface layer and reverse side of adesive side of bonding qualtiy confirming too IS : 2046 Type S ,Includuing cost of adhesive of approved quality.

Providing and fixing aluminium handles anodized transparent or dyed to required colour - Handel

Catcher

Provding and fixing of 4mm thick glazed shutter i/c glass for window and celerstorey windows using 4 mm thick float glass pens ,ISI Marked Ms Presswd Butt Hinges Bright Finished of Required Size With Neccesary Secrews 2nd class teak wood

Preparation and fixing wire gauge shutter using galvanised with MS wire gauge of avcrage width of aperturre 1.4 mm thick in both direction with wire of dia 0.63 mm for doors & windows and clerestory window i/c bright finished/black enamelled iron hinged with necessary screws .2nd class teak wood.

P/F M.S. grills required pattren in wooden frame windows etc. with M.S. flats / square or round bars with round headed bolts and nuts or by screws i/c red oxide priming coat (With material) fixed to opening /wooden frames with rawl plugs screws etc.

Fixing anodied sliding dor bolt anodized transpoet or dyed to required colored and shade with bolts and nuts screws etc. complets 300x16mm small 250x16mm foe D 1&2 - 300x16

P/F M/s Tower bolt (barrel type) -do- D 300x10mm or W 250x10mm

P/F M/S handles -do - as per above item

Fixing of M.S. Hooks and Eyes

P/F hydraulic door closer

15mm thick cement plaster in 1: 5 in faire / rough side of brick walls for plastering up to floor two level i/c arises internal rounded angles, chmfers and or rounded not exceeding 10mm in girth and finished even and smooth i/c scaffolding

52mm thick cement concrete flooring with concreate hardner toping ,underlayer 40 mm thick cement concrete 1:2:4(1 Cemnet 2: Coarse sand 4 graded stone aggregate ) 20mm nomional size and top layer 12mm thick cement hardner consisting of mix 1:2(1 cement hardner mix : 2 Graded stone aggregate 6mm nominal size) by volume, hardning compound mixev @2ltr. per 50kg. of cement or as per manufacturer's specefications. This includes cost of cement slurry, but excluding the cost of nosing of steps ets. complete.

Providing and laying spartic ceremic tiles 5.5mm.thick in flooring (300 x300mm. size) treads of steps laid on a bed of 12mm. thick cement mortar 1:3(1cement: 3 sand) finished with flush pointing in white cement. Detail of cost for one Sq.m.

Providing and laying spartic ceremic tiles 5.5mm.thick in flooring (300 x300mm. size) treads of steps laid on a bed of 12mm. thick cement mortar 1:3(1cement: 3 sand) finished with flush pointing in white cement. Detail of cost for one Sq.m.

Making Plinth Protection 50mm thick in cement concrete 1:3:6 (1cement: 3 coarse sand zone III : 6 graded stone aggregate 20mm nominal size) over 75mm thick bed of dry brick blast 40mm nominal size well rammed and consolidated and grouted with fine sand including necessary excavation leveling and dressing and finishing the top smooth

Constructing course rubble hammer dressed U shaped open surface drain with side wall 15x22cm in cement mortor 1:6 plastering with cement mortor 1:3 including earth work and laying 10cm cement concrete in 1:5:10 & 7.5cm cement concrete in 1:2:4 stone agrregrate of 20mm nominal size and finished with a floating coat of neat cement complete as per standard designetc.

Applying priming coat over new steel work and other metal surfaces after and i/c preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matters scoured with wire brushes, fine steel scrapers & sand paper complete with ready mixed priming paint brushing res lead red oxide/zinc oxide chrome

Painting Two Coats ( Excluding Priming Coat ) on new steel and other metal surfaces with enamel paint brushing to give an even shade i/c cleaning the surface of all dirt, dust and other foreign matter

Applyng primary coat over new wood and wood based surface after and i/c preparing the surface by throughly oil grease, dirt and other foreign matter sand papering 5 knotting (ready mixed paint brushing wood priming paint)

Painting two coats on new wood and wood based surfeces with enamel paint to give an even shade i/c cleaning the surface dirt dusr and other foreign matter and sand papering slopping

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and others foreign matters sand papered smooth to give final matter finish to the surface complete

Applying one coat of water thinable cement primer of approved brand and manufacture on wall surface water thinable cement primer

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter wtc. including sand paper smoot complete

Please Enable Macros to View BoQ information