Interior Fit out works of office space at Plate-A Rear Side, 1st Floor, Office Block -1, East Kidwai Nagar, New Delhi -110023

S NO DESCRIPTION AMOUNT AMOUNT AMOUNT

DSR NON DSR TOTAL

2.00 PLUMBING/ SANITARY WORKS ₹74,339.05 ₹6,09,646.71 ₹6,83,985.76

16.00 ARTIFACTS/SCULPCTURE ₹0.00 ₹5,70,000.00 ₹5,70,000.00

Digitally signed by AMIT

Total (DSR+MR) ₹4,01,23,963.65

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - CIVIL WORKS

S NO DSR/MR DESCRIPTION QUANTITY UNIT RATE AMOUNT AMOUNT

DSR 2023 VOL- DSR RATE NON DSR

1 FLOORING WORKS

CEMENT CONCRETE: Providing and laying in position CEMENT CONCRETE of specified grade exluding the cost of centring and

4.1 shuttering-all work upto plinth level.

1: 4: 8 (1 Cement: 4 coarse sand: 8 graded stone aggregate 40mm nominal size)

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st

quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick

Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and

1.02 11.40 matching pigments etc., complete. 15 Sqm ₹1,439.40 ₹21,591.00

ALUMINIUM SKIRTING: Supply of 100mm Aluminium (Grade 6063) Skirting with 15 micron anodising In Natural Finish. Thickness

1.30 to 1.50mm. Designed to conceal screws. Seamless finish. Complete with Rubber/ PVC Jointers and Gasket.

ENGINEERED WOODEN FLOORING: Supplying and Installation of engineered wooden flooring of total thickness 13 mm -16 mm,

Toplayer PEFC controlled Core board PEFC controlled Backing layer PEFC controlled sources Wood Veneer 2 mm Tongue and

groove Length Uniclic Width Uniclic Multifit Domestic use Conditions as per direction of engineer in charge.

VITRIFIED TILES FOR FLOOR & WALLS: Providing and laying Vitrified tiles full body with smooth surface in floor (thickness 15 mm

to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand &

manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming

to IS: 15477, in average 6 mm thickness as per direction of Engineer-in-charge.

Pattern Tile 600x600mm

CARPET TILES: Providing and laying carpet tile flooring. Carpets shall be of Type 6 nylon loop pile carpet tiles/Plank. The carpet shall

have sufficient gauge (1/10 ~ 1/12) with sufficient stitches (10~13) per inch. The carpet shall be solution dyed fibre content or with

injection printing technology. The carpet shall have the pile height ranging from (2.0 ~ 3.0) mm with average density higher than 4500

Oz/ cubic yard. The total thickness of the carpet tile shall also range from (5.5 ~ 6.0) mm.

ITALIAN MARBLE: Providing and laying machine cut, mirror polished, Italian Marble brass brass inlay stone flooring laid in required

pattern in linear portion of the building all complete as per architectural drawings, with 18mm thick stone slab laid over 20mm

(average) thick base of cement mortar 1: 4 (1 cement: 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including

pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all

complete as specified and as directed by the Engineer-in-Charge.

18 mm thick Italian Marble stone slab in all colour and shade

IPS FLOORING: 52mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4

(1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12mm thick cement hardener consisting of

mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per

50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps

Digitally signed by AMIT

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired

shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-

11.48 in-charge.

Size of Tile 600x600 mm

TOTAL FLOORING WORKS ₹10,40,483.45 ₹14,96,405.00

Digitally signed by AMIT

2 FALSE CEILING WORKS

GYPSUM BOARD CEILING: Providing and fixing false ceiling at all height including providing and fixing of frame work made of special

sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and

consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one

flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle

hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate

G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom

wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction

perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction,

including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to

wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of

gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including

jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes ,

finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all

as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with

frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but

excluding the cost of painting with

12.5mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

WOODEN VENEER CEILING SQUARE PANEL(2FT X 2FT): Providing and fixing wooden veneer ceiling panel of 2ft x 2ft size by

fixing Natural OAK Veneer 4mm on 12mm underlay fire retardant ply fixed to a subframe made using 50mmx50mm Kiln seasoned and

chemically treated hollock wood fixed to RCC ceiilng using Fasteners.

POLISH: Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following

process in the sequence as detailed below:

1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos.

2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12

3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the

surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big

holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further

allowed to dry for 12 hrs.

4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required

proportion.This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to

dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine

thinner mixed in required proportion complete coat to be done in 1 or 2 layers without gap of time) as per direction of Engineer-in-

BAFFLE CEILING: Providing & fixing polylam blades vertical & horizontal baffle system, exhibiting space-delineating characteristics.

The system comprises baffles 50mm wide & 100 Deep thickness of minimum 0.5mm GMS, installed at 150mm C/C. The C shaped

shaped carrier rails run perpendicular to themain baffles profiles. Individual baffle lengths between 300 and 2400 mm can be selected.

Baffle are supplied with the end cap matching the similar finish of baffle. Tolerances according to TAIM, DIN EN 13964 and quality

controlled to ISO 9001:2015 approved by SIS. Substructure for POLYLAM® Vertical baffle system consisting of C shape carrier of

minimum 1.2mmthickinstalled perpendicularly to baffles, same was hanged to wall with the help of wall anchor fasteners. Baffles to be

connectedperpendicular to C shaped carriers with the help of baffle hanger brackets. The primary profiles must be connected to

oneanother with longitudinal splice connectors. C shaped baffle carriers to be installed at maximum distance of 1200mm. in a length of

2400 mm baffles.Manufacturer shall have the fully automatic powder coating system with power and free conveyorize 3mtr/minute

capacity. Powder coating plant shall be equipped with latest modern technology with fully automatic inline Pre-treatment using nano

technology, Inline automatic water Drying system after pre-treatment. Mode of Measurements: Measurements shall be wall to wall

2.04 MR without any deductions for lights, diffuses, columns etc.. IN WOODEN FINISH 20.00 sq m ₹5,764.00 ₹1,15,280.00

Digitally signed by AMIT

PERFORATED MS GRID CEILING: Supply, Installation, Testing and Commissioning of perforated metal grid ceiling system made of

Mild Steel (MS), consisting of factory-perforated metal panels/modules of approved pattern, manufactured from MS sheet of minimum

0.8–1.0 mm thickness, finished with polyester white powder coating applied over a 5-stage pre-treatment process, suitable for

suspended ceiling applications, including concealed T-grid / hook-on suspension system, GI suspension rods, hangers, perimeter

angles, fixing accessories, edge trims, cut-outs for light fixtures, air-conditioning diffusers and services, complete with proper

alignment, levelling, cutting and making good wherever required, including testing, commissioning and handing over, complete.

Material: Mild Steel (MS)

Finish: Polyester powder coated

Type: Perforated metal ceiling panels

Mounting: Suspended ceiling system

Suspended acoustic ceiling - Providing and Fixing Suspended acoustic ceiling out of 12mm per panels 300mm High cut in curved

profile placed in criss-cross panels as shown in the Visual. Cost to include the necessary Suspensions/Hardware required for the

ceiling all complete. Basic rate of 12mm th. Acoustic sheet with Installation & CNC cutting area to be measured and certified for

TOTAL FALSE CEILING WORKS ₹4,34,188.65 ₹8,68,196.00

3 WALL FINISHES WORKS

DOUBLE GLAZED GLASS PARTITION SYSTEM WITH GLASS COMBINATION OF 10MM + AIRGAP + 10MM TOUGHENED

GLASS): Supply & Installation of Aluminum profile with top & bottom profiles of size 82mm x 38mm in Natural Anodized / Black finish.

Partition sides to be fixed with mullion and it's covers should be easily accesible while removal of glass, if & when required. Glass to be

fixed with suitable EPDM gaskets for insertion of combination of 10mm thick clear toughened glass + 58 to 62 mm Air Gap + 10 mm

thick clear Toughened Glass. Glass should not placed directly on profiles for giving more strength. It should be placed on aluminium

spacer profiles and spacers should be covered with cover profiles. Partition Glass joineries consists of two-way Polycarbonate I-

profiles, 90 Degree Polycarbonate L-Junction and Polycarbonate T-Junction profiles. Polycarbonate profile joineries to be fixed with

double sided adhesive tape & profiles to be inserted in the joint instead of sealing it with sealants. Polycarbonate profiles to be used to

give continuity glass effect. Hardware for fixing profiles to be used as per manufacturer standard. Costs should be inclusive of

3.01 MR necessary Hardware for fixing of profiles & installation charges. 84.76 sq m ₹8,515.00 ₹7,21,690.00

DOUBLE GLAZED GLASS DOOR WITH FOR COMBINATION OF 8MM + AIRGAP + 8MM TOUGHENED GLASS: Supply &

Installation of aluminium Door frame of size 82X55mm and double glazed stile door frame of size 82x40 mm with necessary seals in

natural anodized / black finish with specially designed Aluminium Hinges (5 Nos.) & Lever Handle in Oval shape SS304 with SS 35mm

Backset of 22mm Square Forend with Strike plate. Door should have Lock, oval escutcheons, strike plate, EPC One Side Key other

side knob-70mm and exposed Door closer with EN 3/4 standard rating. Door should have glass combination of 8mm toughened

glass+Airgap + 8mm toughened glass and necessary seals to be provided all around the door frames along with drop down seal.

Profile & hardware should be from same brand to give end to end solution. Cost should be inclusive of installation charges of Door.

SINGLE GLAZED GLASS SLIDING DOOR WITH FOR COMBINATION OF 8MM + AIRGAP + 8MM TOUGHENED

GLASS: Providing and fixing aluminium sliding door using extruded standard tubular sections/ Z-sections of approved

make conforming to IS: 733 and IS: 1285, anodised to minimum grade AC 15 as per IS: 1868, including necessary EPDM

gaskets, cleats, angle screws, and all other accessories for the sliding mechanism, complete as per architectural drawings

and direction of Engineer-in-charge. (Glazing/paneling, handles, and locking arrangements to be measured and paid for

9.1 WOODEN DOOR FRAMES: Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed

3.03 9.1.1 Second class teak wood 0.06 cu m ₹1,42,949.70 ₹8,576.98

WOODEN BATTENS: Providing and fixing specified wood frame work consisting of battens 50x25mm fixed with rawl plug and drilling

8.27 necessary holes for rawl plug etc. including priming coat complete.

3.04 8.27.1 Kiln seasoned and chemically treated hollock wood 0.06 CUM ₹1,87,277.65 ₹11,236.66

Digitally signed by AMIT

FLUSH DOOR SHUTTERS: Providing and fixing on all height prefabricated factory made 40mm thick flush door shutter in existing

door frame bounded with BWP type synthetic resin adhesive & wooden fillers as per IS 848 -1974 shutter should be confirm IS:2202

(part-1) non decorative type flush door of area up to 1.80 to 2.50 sqm and nothing shall be paid on account of size variation upto 5%

plus mimus of make Greenlam, Duro, Century or Equivalent with both side 4mm thick decorative teak veneering of make sapele/white

american oak/vintage teak including fixing on all edges 8mm thick second class teak wood margin/lipping with 8 mm thick clear

vision/frosted glass fitted vertically in flush door shutter of make Saint Gobin, Modi Guard & Hindustan National Glass fixed all-round

by 4mm thick second class teak wood margin/molding and size of cut in flush door shutter will be approx. 200x1800mm or as per

approved drawing and one no. of door rubbershutter finished complete with PU polish all-round i/c SS butt hinges and SS screws all

complete as per the direction of engineer-in-charge. (Note: this item is inclusive of all material, T&P and labour involved and the work

3.05 MR. shall be executed as per the approved drawing). 2.00 Nos ₹3,203.00 ₹6,406.00

WOODEN LIPPING: Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door

3.06 9.23 shutters (over all area of door shutter to be measured). 2 SQM ₹462.35 ₹924.70

FLUSH DOOR FLOOR MACHINE: Providing Double cylinder Floor Spring D-120 for Wooden door with Closing Force EN 4 with

Maximum door weight 120 Kg. Maximum door width 1250 mm.Closing speed : 130° Final closing speed : 15-0°. Hold Open (standard):

90° hold open. Weight of floor spring approx : 6kg, 5,00,000 cycles Tested. approved make and model all complete as per the

direction of Engineer-in-charge.

TOP & BOTTOM STRAP: Providing top and Bottom Strap for wooden doors of approved make and model all complete as per the

direction of Engineer-in-charge.

FLUSH DOOR DEAD LOCK: Providing and Fixing 160 mm Euro Dead lock with Rose rings for wooden doors of approved make and

model all complete as per the direction of Engineer-in-charge.

FLUSH DOOR LOCK CYLINDER: Providing and Fixing 60 mm Eco Pin Cylinder 1CK SS Cylinder One side knob and one side

regular key for wooden doors of approved make and model all complete as per the direction of Engineer-in-charge.

FLUSH DOOR HANDLE: Providing 32x840 mm SS 304 H type Handle for wooden doors. Material: Stainless Steel.

Finish: Satin Stainless Steel (SSS). of approved make and model all complete as per the direction of Engineer-in-charge.

WOODEN DOOR LOCK: Providing and Fixing Dead lock Back set- 50 mm with Key Hole of approved make and model all complete

3.12 MR as per the direction of Engineer-in-charge. 0 Each ₹4,029.00 ₹0.00

GLASS FILMS: Providing & Fixing Frosted Translucent, cast PVC, self-adhesive vinyl, special CRYSTAL-effect film to reproduce

Sand-blasting effect on glass with customised designs, thickness of 2 mil (0.05mm) without adhesive & 3mil (0.8) with adhesive having

3.13 MR minimum tensile strength of 3.5 pound/inch at 73 F (0.6 kg/cm at 23 C). Adhesion after 24hrs of installation should be 4 pounds/inch 80.00 SQM ₹956.00 ₹76,480.00

TOILET DOOR MORTIZE LOCK: Providing and Fixing ss 304 D Type Tube Lever Mortise Combi SET with 60 mm Cylinder keyless

and Lock Body SS for wooden Toilet doors of approved make and model all complete as per the direction of Engineer-in-charge.

TOILET DOOR LOCK BODY: Providing and Fixing 240 mm lock body for wooden doors of approved make and model all complete

MR as per the direction of Engineer-in-charge. Each ₹1,430.00 ₹2,860.00

TOILET DOOR CLOSER : Providing and Fixing Door closer Hercules -60 kg for wooden doors of approved make and model all

complete as per the direction of Engineer-in-charge.

DOOR HINGES : Providing and Fixing SS 304 Hinges Four Ball Bearing 100x75x3 mm (with screws) for wooden doors of approved

3.17 MR make and model all complete as per the direction of Engineer-in-charge. 8.00 Each ₹364.00 ₹2,912.00

3.18 MR LACQUERED GLASS: Providing and fixing of 6mm thick annealed SGG Planilaque Evolution (premium GRIHA rated lacquered glass 5.00 SQM ₹5,004.00 ₹25,020.00

Digitally signed by AMIT

GYPSUM BOARD PARTITION: Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including

providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both

side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor

and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor

fastener or metal screws with nylon plugs and the studs 48mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm

thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts

and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with

nylon plugs at spacing of 450mm centre to centre, and fixing of boards to both side of frame work by 25mm long dry wall screws on

studs, floor and ceiling channels at the spacing of 300mm centre to centre. The boards are to be fixed to the frame work with joints

staggered to avoid through cracks, M.S. fixing channel of 99mm width (0.9mm thick having two flanges of 9.5mm each) to be provided

at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush

finish with recommended jointing compound, jointing tape, angle beads at corners (25mmx25mmx0.5mm), joint finisher and two coats

of primer suitable for board as per manufacturer's specification and direction of engineer in charge all complete.

75mm overall thickness partition with 12.5mm thick double skin fire rated Glass Reinforced Gypsum (GRG) plaster board conforming

3.19 9.105.1 to IS: 2095: part 3 (Board with BIS certification marks) 50.00 SQM ₹2,131.10 ₹1,06,555.00

ACRYLIC SOLID SURFACE CLADDING: Supply & Installation of 12 mm thick Thermoformable Acrylic Solid Surface Sheets (DuPont

Corian/ Tristone/ Lotte), over a robust substrate made out of BWP/ Flexi Ply/ MS- Aluminum sections etc. as required, to achieve

stated design intent. ASS in 12mm thickness, shall be manufactured as per guidelines of ISO 19712. ASS sheets to be cut, pasted and

finished over the substrate as provided, to achieve smooth and seamless finish. Item cost include intend adaptation, supply, freight

and installation of ASS sheets to site, wastage, finishing, creating provisions/ cut-outs for accessories and final placement of table.

Work shall be done by company's authorized Quality Network (QN) fabricator, as per satisfaction of Engineer-in-Charge. Colours :

Basic, Solid and small speckled (Group I & 2)

WINDOW BLINDS : Providing & supplying of fabric venetian Window Blinds as per the approved sample, consisting of 3" vane size

having head rail, rotator rail and bottom rail made of aluminium powder coated and provided in standard natural white color. The rolling

tube should be made up of aluminium alloy from. The head rail dimensions should be of suitable size according to the length of head

rail and space available and finished with fabric cover matching with the louver fabric. The cassette should conceal the working

mechanism rotary-clutch. (White polycarbonate spring tempered rotary clutch which raises), lower and tilts the blinds. White

polycarbonate limit assemblies control vane over-rotation, located on either side of individual blinds. All parts, components & hardware

are in approved shade as per direction of Engineer-incharge.

3.22 MR PELMET: Fabricate and install pelmet made of 19mm thick board, up to 300mm high and in line with external glazing as per details of 35.00 RM ₹225.00 ₹7,875.00

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered

wall surface to prepare the surface even and smooth complete.

3.26 13.83 Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50

14.1 Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper

3.27 14.1.2 With cement mortar 1:4 (1cement: 4 coarse sand) 50.00 Sqm ₹560.50 ₹28,025.00

3.28 MR 5.5mm THICK HDHMR BOARD (BOTH SIDE RAW): Providing and fixing in wall lining, partitions etc. Confirming to ASTM E-84-2021 50.00 Sqm ₹504.00 ₹25,200.00

5.5mm thick HDHMR Board

11 mm THICK HDMR BOARD ( BOTH SIDE RAW ): Providing and fixing 11mm thick HDHMR board in wall lining, partitions etc. both

side raw. Extra density, high moisture resistance, borer, termite & fungus resistance, green material and environmental friendly with

3.29 MR 11 mm thick HDHMR Board 120.00 SQM ₹851.00 ₹1,02,120.00

Digitally signed by AMIT

5.5mm THICK HDHMR BOARD ( ONE SIDE LAMINATE ): Providing and fixing in wall lining, partitions etc. Confirming to ASTM E-84-

2021 class1 one side 1mm decorative Lamination and other side raw, having even grade low emission, high moisture resistance, fire

resistance, borer, termite & fungus resistance, green material and environmental friendly with necessary fixing arrangement and

screws etc. , complete as per direction of Engineer-in-Charge

3.30 MR 5.5mm thick HDHMR Board 50.00 SQM ₹720.00 ₹36,000.00

ALUMINIUM FRAME: Providing and fixing partition, frame work in 50x25x1.5mm Aluminium Section placed at 600mm centre to centre

both ways (horizontal & vertical) fastened to floor, ceiling and horizontal member. The item includes providing and fixing 50mm thick

3.31 MR polyester synthetic insulation as insulation of 100 GSM. 80.00 SQM ₹1,347.00 ₹1,07,760.00

FIBRE WALL COVERING: Supply & Installation of Glass fiber based homogenous Woven/ non-woven .1mm thick, 100-200 GSM

Density brethable Wall Coverings. Material to be fire certified with minimum Euroclass BS1D0 certification under EN13501, no harmful

chemical coated with Oekotex Standard 100 certification and non-toxic in nature for closed enviornments with A+ attested for emission

in indoor air. Installation to be done over smooth, dry and dust-free substrate as specified with OEM recommended adhesive by the

supplier's authorized installer team. Installation measurement as per the entire area (concealed/visible) installed. Finished as per

satisfaction of E.I.C. PAINTABLE

3D ACOUSTIC PET WALL PANELLING: Providing and fixing Smart Acoustical Wall Panels with square edges made of Polyester

fiber substrate 12mm thick with acoustical properties and with an option of 12 colours as per the choice of the Architect/ Person in-

charge, providing a minimum sound absorption level of 0.50-0.90 NRC, to be affixed to wall using Adhesive. The material should

adhere to Formaldehyde emission standards of GB18580-2001 class E1, asbestos-free, non-toxic, non-irritant and recyclable.

Material to have fire resistance as per B1 Chinese standards. The sheets to have density of 200 kg/m3 and weight of 2.0 kg/m2. The

sheets to be made available as per the V groove design approved by Architect/ Person in charge(attached Pic). Cutting to be in done

by supplier using blade cutting as per requirement.

LAMINATE PANELLING: Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede

finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including

cost of adhesive of approved quality.

Graphic Work: Providing and fixing printed graphics work on the ready base work. Cost to be included for the base prepration and

3.36 printed graphic including the cost of printing and fixing of the grapichs 10.00 SQM ₹2,100.00 ₹21,000.00

Wallpaper : Providing and fixing premium quality vinyl-based / textured wallpaper of approved make, shade and pattern, with

minimum 250–350 GSM, suitable for commercial interiors, complete with all materials, labour and tools. The work shall include surface

preparation by removing dust, loose particles and unevenness, application of primer/sealer, and fixing wallpaper using manufacturer-

approved adhesive ensuring proper alignment, joints, pattern matching, bubble-free and wrinkle-free finish.

Rate includes cutting to size, edge finishing, wastage, protection during execution, and cleaning after completion, complete as per

drawings, specifications and the direction of the Architect/PMC. 20.00 SQM ₹3,200.00 ₹64,000.00

Parametric Design Wall: Providing and fixing parametric design wall with laminated finish pannels to be cut in parametric design in

3.38 18mm thick pannels to be fixed with required hardware. 25.00 SQM ₹16,500.00 ₹4,12,500.00

TOTAL WALL FINISHING WORKS ₹5,67,629.34 ₹39,43,303.00

4 MISCELLANEOUS WORKS

4.01 MR MODULAR KITCHEN - UNDER COUNTER STORAGE CABINETS: 5.00 SQM ₹12,812.00 ₹64,060.00

Digitally signed by AMIT

MODULAR KITCHEN - OVERHEAD STORAGE WALL UNITS:

Modular Kitchen - Overhead storage wall units:

Providing & fixing factory made modular kitchen cabinets in modular type knockable cabinet boxes with openable shutters and

sufficient number of drawers made of 18 mm thk. HDHMR board with lamination in frosty white laminate with 0.8 mm laminate

complete with 0.8 mm edge banding.All shelves should be supported on approved quality SS pins and shall be adjustable for different

heights as per requirements.Shutters and drawers fascia shall be at least 18mm thic with laminate on both sides with 18mm wide 2mm

thick PVC edge banding, All Shutters/ drawers finished in high gloss acrylic of approved make- Rehau,Ornare,Senosan and having

handless profiles. The unit shall be fixed to the floor/ wall/slab using metal screws of appropriate size and raw plugs. Only front face

area of cabinets and skirting from floor to top of boxes shall be considered for measurement and payment. Cabinet boxes size would

be varies from 400X320X710MM to 1000X320X710MM (approx.) and join together as per site requirements etc. Handle

Profile,Aluminum Handle Profile for lift ups,O* Hinges,Corner Hinges,PVC legs,Skirting,Connector,Screw,Wall Mount set. Complete all

as per the direction of Engineer in Charge.

Providing and fixing of Innotech with metal sides and quadro channels.

4.02B MR Providing and fixing of Bottle pulout 200mm. 1.00 Each ₹11,531.00 ₹11,531.00

WATERPROOFING: Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C.,

kitchen and the like consisting of:

(i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended

proportions including rounding off junction of vertical and horizontal surface.

(ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended

proportion including rounding off junction of vertical and horizontal surface.

(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.

(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with

SHOP DRAWINGS: Preparation of complete set of GFC drawings including finishing, MEP services, details, design calcualtions etc.

and for prepration of as built drawing any other details as and when desired by Engineer Incharge/ client. A qualified professsional for

the purpose shall be appointed after due appproval from Engineer-In-Charge.

Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including

loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of

Engineer-in-charge. Note - item to be applicable in urban areas having directions for restricted hours for movement/ plying of load

carrying motor vehicle of 3.5 cum or more.

6.13 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up

4.10 6.13.1 Cement mortar 1: 3 (1 cement: 3 coarse sand) 25.00 sqm ₹1,150.50 ₹28,763.00

DEMOLITION & DISMANTLING WORKS

Demolition of brickwork manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable

material within 50 metres lead as per the direction of the engineer in charge

Providing & fixing Access Panel of size mentioned below having - 1. Outer aluminium frame - thickness : 1.5mm ( plus 0.2mm thick

powder coating) Material : ENAW6063. 2. Inner Aluminium frame - thickness: 1.5mm (plus 0.2mm thick powder coating) Material :

ENAW6063. 3. Corner fittings, inner frame - material: Hot dipped galvanized steel plate Thickness 2.0mm, with zinc Coating of 200g.

4. Corner fittings, outer frame - material: Hot dipped galvanized steel plate Thickness 2.0mm, with zinc Coating of 200g. 5. 12mm

plasterboard ( Knauf Brand) Type: moisture resistant ( MR) in green plasterboard liner. 6. Screw ( self - drilling black phosphate ) -

Material: mild steel C1018 - 1022. 7. Sealing strip, width, thickness - width: 9.0mm, thickness: 4.0mm. 8. Snap Lock ( spring catch/

catch lock ) - Type of lock: touch latch, Material of lock: plastic ABS, cold rolled steel Q235. 9. Hinge - Thickness : 4.0mm, Length:

82mm; Material: SS2172 ( cold drawn steel wire ). 10. Powder coating - Color: white, RAL 9010

Providing & fixing Access Panel of size mentioned below having - 1. Outer aluminium frame - thickness : 1.5mm ( plus 0.2mm thick

powder coating) Material : ENAW6063. 2. Inner Aluminium frame - thickness: 1.5mm (plus 0.2mm thick powder coating) Material :

ENAW6063. 3. Corner fittings, inner frame - material: Hot dipped galvanized steel plate Thickness 2.0mm, with zinc Coating of 200g.

4.15 MR 4. Corner fittings, outer frame - material: Hot dipped galvanized steel plate Thickness 2.0mm, with zinc Coating of 200g. 5. 12mm 2 Nos. ₹4,010.00 ₹8,020.00

Digitally signed by AMIT

Providing & fixing Access Panel of size mentioned below having - 1. Outer aluminium frame - thickness : 1.5mm (plus 0.2mm thick

powder coating) Material : ENAW6063. 2. Inner Aluminium frame - thickness: 1.5mm (plus 0.2mm thick powder coating) Material :

ENAW6063. 3. Corner fittings, inner frame - material: Hot dipped galvanized steel plate Thickness 2.0mm, with zinc Coating of 200g.

4. Corner fittings, outer frame - material: Hot dipped galvanized steel plate Thickness 2.0mm, with zinc Coating of 200g. 5. 12mm

plasterboard ( Knauf Brand) Type: moisture resistant ( MR) in green plasterboard liner. 6. Screw ( self - drilling black phosphate ) -

Material: mild steel C1018 - 1022. 7. Sealing strip, width, thickness - width: 9.0mm, thickness: 4.0mm. 8. Snap Lock ( spring catch/

catch lock ) - Type of lock: touch latch, Material of lock: plastic ABS, cold rolled steel Q235. 9. Hinge - Thickness : 4.0mm, Length:

82mm; Material: SS2172 ( cold drawn steel wire ). 10. Powder coating - Color: white, RAL 9010

Providing & fixing Access Panel of size mentioned below having - 1. Outer aluminium frame - thickness : 1.5mm (plus 0.2mm thick

powder coating) Material : ENAW6063. 2. Inner Aluminium frame - thickness: 1.5mm (plus 0.2mm thick powder coating) Material :

ENAW6063. 3. Corner fittings, inner frame - material: Hot dipped galvanized steel plate Thickness 2.0mm, with zinc Coating of 200g.

4. Corner fittings, outer frame - material: Hot dipped galvanized steel plate Thickness 2.0mm, with zinc Coating of 200g. 5. 12mm

plasterboard (Knauf Brand) Type: moisture resistant (MR) in green plasterboard liner. 6. Screw (self-drilling black phosphate) -

Material: mild steel C1018 - 1022. 7. Sealing strip, width, thickness - width: 9.0mm, thickness: 4.0mm. 8. Snap Lock (spring catch/

catch lock) - Type of lock: touch latch, Material of lock: plastic ABS, cold rolled steel Q235. 9. Hinge - Thickness : 4.0mm, Length:

82mm; Material: SS2172 (cold drawn steel wire). 10. Powder coating - Color: white, RAL 9010

CUSTOMISED JOINERY UNIT: Supply and fixing of full height storage units (upto 600mm depth) made out of 18mm plywood finished

with approved .8mm laminate on the inside and outside. Hardware used of Hettich make.Complete as per the direction of Engineer in

Customised Bench Seating & podium for Sculpture as per details.

TOTAL MISCELLANEOUS WORKS ₹1,12,253.40 ₹8,33,201.00

0.973 Multiplication factor on DSR ₹20,96,381.86

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - SANITARY & PLUMBING WORKS

2023/ MR S NO DESCRIPTION UNIT QTY RATE AMOUNT NDSR AMOUNT

Supply, Installation, Testing and Commisioning of SINGLE LEVER CONCEALED

BASIN MIXER (WALL MOUNTED) WITH SPOUT (COMPOSITE ONE PIECE BODY)

Supply, Installation, Testing and Commisioning of TABLE TOP BASIN, SIZE:

Supply, Installation, Testing and Commisioning of suitable compatible WASTE

COUPLING 32MM- FULL THREAD- WITH CERAMIC CAP-*130MM HEIGHT *65MM

MR 3 CERAMIC CAP EACH 2 ₹2,032.20 ₹4,064.41

Supply, Installation, Testing and Commisioning of BOTTLE TRAP (WITH INTERNAL

PARTITION) 32mm SIZE WITH 300mm & 190mm LONG WALL CONNECTION

PIPES & WALL FLANGE

Supply, Installation, Testing and Commisoning of RIMLESS, BLIND INSTALLATION

WALL HUNG WC WITH UF SOFT CLOSE SLIM SEAT COVER, HINGES AND

MR 5 ACCESSORIES SET, SIZE: 375X520X400 MM EACH 2 ₹12,785.59 ₹25,571.19

Supply, Installation, Testing and Commissioning of PNEUMATIC CONTROL PLATE

Supply, Installation, Testing and Commisoning of ANGULAR STOP COCK WITH

MR 7 WALL FLANGE EACH 3 ₹4,087.29 ₹12,261.86

Supply, Installation, Testing and Commissioning of CONCEALED STOP COCK WITH

ADJUSTABLE WITH WALL FLANGE 15mm

Supply, Installation, Testing and Commisiong of HAND SHOWER (HEALTH FAUCET)

WITH 8mm DIA 1.2 METER LONG FLEXIBLE TUBE AND WALL HOOK ALD-CHR-

MR 9 573 or equivalent EACH 2 ₹2,153.39 ₹4,306.78

Supply, Installation, Testing and Commisiong of PNEUMATIC SINGLE PIECE SLIM

CONCEALED CISTERN BODY WITH INSTALLATION KIT & “S-TYPE” DRAIN PIPE

CONNECTION SET FOR WALL HUNG WC (WITHOUT FLUSH CONTROL PLATE)

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste

17.28 fittings complete.

17.28.2 Flexible pipe

Providing and fixing mirror of superior glass (of approved quality) complete with 6mm

thick hard board ground fixed to wooden cleats with C.P. brass screws and washers

Digitally signed by AMIT

Providing and fixing C.P. brass angle valve for basin mixer and gyser points of

18.53 approved quality conforming to IS : 8931

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved

18.53A 13a make and quality as per direction of Engineer-in-charge. EACH 13 ₹74.80 ₹972.40

17.61 Cutting chases in brick masonry walls for following diameter sand cast

18.76 Cutting holes upto 30x30cm in walls including making good the same.

18.76.1 15 With common burnt clay F.P.S. (non modular) bricks EACH 1 ₹416.80 ₹416.80

18.78 16 Making chases upto 7.5 X 7.5 cm in walls including making good and finishing with METRE 2 ₹202.90 ₹405.80

Digitally signed by AMIT

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply, including all CPVC plain & brass threaded fittings,

including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes

& fittings with one step CPVC solvent cement and testing of joints complete as per

direction of Engineer in Charge.

Internal work - Exposed on wall

18.7.2 20mm nominal outer dia pipes METRE 43 ₹335.00 ₹14,405.00

18.7.3 25mm nominal outer dia pipes METRE 10 ₹401.55 ₹4,015.50

18.7.4 32mm nominal outer dia pipes METRE 5 ₹518.75 ₹2,593.75

18.7.5 40mm nominal outer dia pipes METRE 0 ₹702.95 ₹0.00

18.7.6 17 50mm nominal outer dia pipes METRE 0 ₹934.15 ₹0.00

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply, including all CPVC plain & brass threaded fittings,

i/c fixing the pipe with clamps at 1.00 m spacing.

This includes jointing of pipes & fittings with one step CPVC solvent cement and the

cost of cutting chases and making good the same including testing of joints complete

18.8 as per direction of Engineer in Charge.

Concealed work including cutting chases and making good the walls etc.,

18.8.1 15mm nominal outer dia pipes METRE 20 ₹497.80 ₹9,956.00

18.8.2 20mm nominal outer dia pipes METRE 10 ₹537.60 ₹5,376.00

18.8.3 25mm nominal outer dia pipes METRE 5 ₹627.25 ₹3,136.25

18.8.4 18 32mm nominal outer dia pipes METRE 8 ₹739.30 ₹5,914.40

18.51 Providing and fixing C.P. brass long body bib cock of approved quality conforming to

Providing, fixing, jointing and testing in position of ISI marked UV stabilized UPVC pipes for

soil, waste, and vent, Type-B as per IS : 13592 suitable for rubber ring joints, including all

neccessary specials and fittings (confirming to IS:14735) i.e. bends, tees, junctions (with or

without doors), reducers, WC connectors, couplers, expansion joints / bellows, cowels,

clamps, rubber rings, clean outs etc. fixing at wall/ ceiling/ floor level supported by clamp &

hangers etc. in concealed / inside duct / under floor & basement ceiling / external work etc.

including chase cutting as required, excavation and back filling in all kind of soils, suspended

from floor under false ceiling or embedding the pipes laid under floors / building in 75 mm.

alround 1:2:4 cement concrete (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

nominal size) including cost of shuttering for proper completion of the work, breaking and

making good the walls and floors etc. after pipes have been duly laid and tested. The rubber

ring shall confirm to IS:5382.

20 The Pipes will be supported with threaded G I rods & U clamps with nuts, washers etc

a 110 mm dia (Wall Thickness - 3.2 to 3.8 mm) METRE 15 ₹454.24 ₹6,813.56

MR b 75 mm dia (Wall Thickness - 3.2 to 3.8 mm) METRE 7 ₹352.54 ₹2,467.80

Providing, fixing, jointing and testing in position ISI marked (IS:4985) UPVC pipes of min 6 ₹0.00

Digitally signed by AMIT

Providing & fixing UPVC Floor trap of self cleansing design with stainless steel grating ₹0.00

MR 22 Plain Floor Trap (4" Ht) with 50 / 75 outlet and with height raiser EACH 1 ₹454.24 ₹454.24

Extra for providing & fixing 125 mm dia C.P. grating in place of C.I. grating over floor traps.

MR 24 Providing & fixing of SS Floor Cleanout, round or square with rubber seal and flat round cover EACH 1 ₹848.31 ₹848.31

MR 25 with screws

Supply, and other testing

Installation, requiredand

fitting complete as required.

commisioning of toilet waste water super quiet EACH 2 ₹80,000.00 ₹1,60,000.00

MR 25a Supply, Installation, testing and commisioning of toilet waste water super quiet EACH 1 ₹75,000.00 ₹75,000.00

MR 26 Providing and fixing stainless steel tray below sewage pipe of size 200x200x200 mm METRE 30 ₹3,075.42 ₹92,262.71

Supply, Installation, Testing and Commisiong of HIGH FLOW SINGLE LEVER

CONCEALED DIVERTOR FOR BATH & SHOWER

Supply, Installation, Testing and Commisiong of SPOUT FOR BUILT IN

MR 28 BATH/SHOWER MIXER EACH 0 ₹7,946.61 ₹0.00

MR 29 Supply, Installation, Testing and Commisiong of OVERHEAD SHOWER 350x350MM EACH ₹20,423.73 ₹0.00

MR 30 Supply, Installation, Testing and Commissioning of 15 litre geyser(Pantry and Powder EACH 2 ₹10,172.88 ₹20,345.76

MR 31 Supply, Installation, Testing and Commisiong of SOAP DISH HOLDER EACH 1 ₹3,722.03 ₹3,722.03

MR 32 Supply, Installation, Testing and Commisiong of TUMBLER HOLDER EACH 0 ₹3,651.69 ₹0.00

MR 33 Supply, Installation, Testing and Commisiong of TOWEL RACK 600MM LONG WITH EACH 0 ₹13,265.25 ₹0.00

Supply, installation, testing and commissioning C.P. brass twin coat hooks fixed on

MR 34 toilet door with C.P. brass screws EACH 1 ₹650.00 ₹650.00

MR 35 Supply, Installation, Testing and Commisiong of TOILET ROLL HOLDER WITH EACH 1 ₹4,218.64 ₹4,218.64

MR 36 Supply, Installation, Testing and Commisiong of TOWEL HOLDER EACH 0 ₹2,827.12 ₹0.00

17.10 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with

17.10.1 Kitchen Sink with Drain Board

Supply, Installation, Testing and Commisiong of single lever sink mixer (table

mounted) with extractable hand shower dual flow complete with 1.2 m long tube with

MR 38 450 mm long braided hoses EACH 2 ₹6,200.00 ₹12,400.00

Supply and installation of Automatic hand drier in SS BODY of approved make and off

white colour in hand wash area at required height. The fixing of unit shall be done

MR 39 using Birla 3M double sided self adhesive tape as per instructions. EACH 1 ₹13,500.00 ₹13,500.00

Providing and fixing below counter installation type Drinking Water R.O. unit with

MR 40 micron filtration pre-treatment unit, skid mounted R.O. module with pressure pump EACH 1 ₹60,000.00 ₹60,000.00

Permeate tank,

40-50 6 m( long

ltr/hr food grade PP permeate line including connection to

Supplying, handling, storing, insatallation, testing & commissioning of water cooler

MR 42 having nominal cooling capacity of 20 liters per hours, with 20 litres dispenser with 3 EACH 1 ₹14,500.00 ₹14,500.00

nos. of faucets, (cold water tap, normal water tap, hot water tap) to work on one phase

Digitally signed by AMIT

Providing and fixing forged brass ball valve of brass body with hard chrome plated

steel ball inside PTFE (Teflon) seat & ring with chrome plated centre handle with

female BSP threads complete in all respects.

a 15 mm dia nominal bore EACH 2 ₹670.00 ₹1,340.00

b 20 mm dia nominal bore EACH 4 ₹866.00 ₹3,464.00

MR c 32 mm dia nominal bore EACH 1 ₹2,230.00 ₹2,230.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

DSR E&M TOTAL AMOUNT TOTAL AMOUNT

DSR E&M TOTAL AMOUNT TOTAL AMOUNT

S NO DESCRIPTION UNIT QUANTITY RATE

2025 DSR (INR) NON-DSR (INR)

A POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR

PVC insulated copper conductor single core cable in surface/ recessed steel conduit, with

1.3 modular switch, modular plate, suitable GI box and earthing the point with 1.5

sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required.

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point

A.2 independent switch etc.) with 1.5 sq. mm FRLS/HFFR PVC insulated copper conductor single

core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm

Wiring for light/ power plug with 2X4 sq.mm FRLS/HFFR PVC insulated copper conductor

A.3 1.5 single core cable in surface/ recessed steel conduit along with 1 No. 4 sq. mm FRLS PVC Metre 2940 ₹480.00 ₹14,11,200.00

insulated copper conductor single core cable for loop earthing as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch

box including connections but excluding modular plate etc. as required.

1.24.4 3 pin 5/6 amp socket outlet Each 90 ₹136.00 ₹12,240.00

1.24.5 6 pin 15/16 amp socket outlet Each 38 ₹219.00 ₹8,322.00

Supplying and fixing modular blanking plate on the existing modular plate & switch box

A.5 1.26 excluding modular plate as required. Each 200 ₹47.00 ₹9,400.00

Supplying and fixing following size/module, GI box along with Modular base & cover plate on

existing modular metal boxes etc. as required.

B SUBMAIN AND CONTROL WIRING

Wiring for circuit/ submain wiring along with earth wire

1.7 with the following sizes of FRLS/HFFR PVC insulated

2 X 1.5 conductor,

sq. mm + 1single

X 1.5 core cable

sq. mm in surface/

earth wire Metre 250 ₹370.00 ₹92,500.00

1.7.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre 50 ₹476.00 ₹23,800.00

1.7.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 50 ₹652.00 ₹32,600.00

Digitally signed by AMIT

Supplying and making end termination with brass compression gland and aluminium lugs for

11.1 following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1

KV grade as required.

Supply of following XPLE armourned 1.1 KV grade conforming to I.S.7098/1554Aluminium

Conductor Cables :

MR Supply of following sizes of PVC sheathed PVC/XLPE insulated Aluminium conductor armoured

cable of 1.1 KV grade conforming to IS:7098 part-1 / IS:1554 part-1 respectively & ISI marked.

C.2 (a) 3.5 C x 120 Sqmm XLPE cable RM 0 ₹1,078.00 ₹0.00

(b) 3.5 C x 95 Sqmm XLPE cable RM 30 ₹864.00 ₹25,920.00

(d) 3.5 C x 50 Sqmm XLPE cable RM 20 ₹510.00 ₹10,200.00

(e) 3.5 C x 35 Sqmm XLPE cable RM 50 ₹378.00 ₹18,900.00

Supply of following sizes of copper cables -PVC sheathed PVC/XLPE insulated Copper

C.3 MR conductor armoured cable of 1.1 KV grade conforming to IS:7098 part-1 / IS:1554 part-1

respectively & ISI marked.

(a) 4 C x 16 Sqmm XLPE copper cable RM 100 ₹1,446.00 ₹1,44,600.00

(b) 4 C x 25 Sqmm XLPE copper cable RM 25 ₹2,253.00 ₹56,325.00

(c ) 3.5 C x 35 Sqmm XLPE copper cable RM 20 ₹2,686.00 ₹53,720.00

(d) 3.5 C x 50 Sqmm XLPE copper cable RM 20 ₹3,224.00 ₹64,480.00

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit

2.10 breaker suitable for inductive load of following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB

complete with connections, testing and commissioning etc. as required.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB

distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus

bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required.

D.4 (But without MCB/ RCCB/ Isolator)

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual

2.14 current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing

MCB DB complete with connections, testing and commissioning etc. as required.

Digitally signed by AMIT

E PROVISIONS FOR VOICE, DATA, SECURITY & TV SYSTEMS

Supply, installation, testing & Commissioning of 1 module 16A SWITCH SP 1 way for floor box.

E.2 MR Supply, installation, testing & Commissioning of 2 module 16 A Socket for floor box box. Set 2 ₹577.00 ₹1,154.00

Supply, installation, testing & Commissioning of Specific Backbox for Carpet for Floor Box

E.3 MR along with LID and TRIM for tiles/ marble 15 to 20mm thickness material for headband and Set 2 ₹12,106.00 ₹24,212.00

single cable outlet/ glavanized steel, paint RAL 7031 for floor box .

Supply, installation, testing & Commissioning of Specific Backbox for Wooden Flooring for Floor

E.4 MR Box along with LID and TRIM for tiles/ marble 15 to 20mm thickness material for headband Set 2 ₹6,803.00 ₹13,606.00

and single cable outlet/ glavanized steel, paint RAL 7031 for floor box.

Supply, installation, testing & Commissioning of flat support plate 8 module for integration of

Mechanism for Floor Box

Supply, installation, testing & Commissioning of waved support plates for 4 module (2x2)

E.6 MR modules for Floor Box Set 2 ₹1,533.00 ₹3,066.00

Supplying and fixing following modular switch / socket on the existing modular plate & switch

1.24 box including connections but excluding modular plate etc. as required.

1.24.7 TV socket outlet Set 8 ₹168.00 ₹1,344.00

Supply, Installation, Testing and Commisioning of Galavanized Iron (GI) Raceways along with

MR required suitable number of GI couplers for joining raceways and fixing GI brackets and all

accessories complete in all respect as per the directions of engineer in charge

(a) 300mmx38mm(GI) - 3 compartment Mtr 10 ₹3,603.00 ₹36,030.00

E.8 (b) 225mmx38mm(GI) - 3 compartment Mtr 25 ₹2,960.00 ₹74,000.00

Supply, Installation, Testing and Commisioning of Junction boxes for direct access to cables at

the intersection of raceways supplied completely with base and cover plates, height adjustable

junction box 65- 90 mm including all accessories ss plate of 3mm thick complete in all respect

E.9 as per the directions of engineer in charge

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE

E.10 1.19 insulated, shielded with fine tinned copper braid and protected with PVC sheath in the exisitng Meter 120 ₹54.00 ₹6,480.00

surface/recessed steel/ PVC conduit as required

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess

1.20 including painting in case of surface conduit, or cutting the wall and making good the same in

case of recessed conduit as required

Supplying and fixing of following sizes medium class PVC conduit aong with accessories in

1.21 surface/ recess including cutting the wall and making good the same incase of recessed

conduit as required

Digitally signed by AMIT

Supplying and installaton following size of perforated painted with powder coating M.S. cable

trays with perforation not more than 17.5%, in convenient sections, joined with connectors,

E.13 suspended from the ceiling with two numbers MS/GI Suspenders i/c base

of suitable size MS/GI angle, bolts & nuts, painting suspenders, fastener etc as required.

4.1.6 450 mm width X 50 mm depth X 2.0 mm thickness Metre 40 ₹1,243.00 ₹49,720.00

Supply, Installation, Testing and Commisioning of USB charger- 3000mA/15 Watts- Type C- 1

module complete in all respect

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and

F.1 5.6 providing masonry enclosure with cover plate having locking arrangement and watering pipe of SET 2 ₹15,004.00 ₹30,008.00

2.7 Meter long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as

F.4 5.16 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. MTR 100 ₹84.00 ₹8,400.00

G.2 MR Floor Panels

Designing, fabricating, transporting, unloading, storing, fixing in position, testing and

commissioning the following sheet steel cubicle type panels fabricated from 1.6mm thick CRCA

sheet, dust and vermin proof, indoor type TPN Panels with hinged lockable doors fabricated

from 2mm thick CRCA sheet, suitable for 415V, 3 phase 4 wire 50Hz AC supply with rear

access for cable alley and with segregated bus-bar chamber with tinned aluminium bus bar and

including supplying and fixing following switchgears, meters and accessories, inter-

connections, bonding to earth, powder coated painting and marking as specified. Switch boards

complete as per schematic diagram:

Type of construction: Form 3

IP classification: 42

The LT PANEL shall be electrically inter-locked as shown in Schematic diagram and as

detailed in the Specifications

Colour: Gray Powder Coated, as per approved sample.

1 nos, 200 Amps. 4 pole MCCB , i.e four pole Moulded Case Circuit Breaker of fault breaking

capacity 25 KA (ICS=ICU up to 433 V) complete in all respect

TPN aluminum bus bars of minimum of 250 Amps capacity with heat shrinkable colored

sleeves and I/C DMC/SMC bus bars supports at required intervals complete for cross section,

size supports & their spacing etc. for withstanding fault level of 25 MVA for 1 Sec.

(a) 63 Amps, TPN, MCB - 4 Nos.

(b) 40 Amps, TPN, MCB - 6 nos

Panel complete as above Each 1 ₹2,50,000.00 ₹2,50,000.00

H SAFETY ITEMS

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least

H.1 2.21 2 mm thick, and vitreous enamelled white on both sides, and with inscription in single red Each 1 ₹315.00 ₹315.00

colour on front side as required

Digitally signed by AMIT

Online UPS- Input supply: Three Phase, Output supply: Three Phase. Supplying, installation,

Testing & Commissioning of following capacity at full load (Unity Power Factor)

at operating temperature 0 to 40 0C, Relative humidity 0 to 95%, Online double conversion true

sine wave Uninterrupted hot swapable (allow for the replacement or addition of battery modules

without shutting down the entire system) modular Power Supply (UPS) system with N+1

26.2 modules (N denotes total number of modules required for rated capacity).

The UPS shall include a Rectifier, inverter, battery bank suitable for 30 minutes back up

(Battery VAH capacity shall not be less than 1600 VAH per KVA of

UPS rating per Hour backup time) on full load (Battery shall be VRLA, SMF in ABS Container)

and Static Bypass switch along with provision for manual bypass, suitable isolation transformer

for additional protection against neutral faults etc. UPS shall have inbuilt phase sequence

correction. The UPS systems offered are to be of the latest technology with Digital Control

10KVA (Each Power module shall be < 10 KVA)

Total of Electrical items ₹33,46,847.00 ₹14,25,859.00

Digitally signed by AMIT

Unit Price DSR Amount NDSR Amount

S. No Description Unit Qty.

Supplying, Installation, Testing & Commissioning of Modular type Variable Refrigerant Flow/Variable

Refrigerant Volume air cooled Outdoor units suitable for

cooling/heating having 100% hermetically sealed inverter

type twin Rotary/Scroll Compressor(s),minimum two

compressors (with individual separate PCB) for above

14HP modules, microprocessor based Controller, top

discharge type condensing unit(s), with R-410-A

Refrigerant or equivalent, vibration Isolators with suitable

foundation etc. complete as required. To have better

efficiency condenser fan shall be capable to operate at

31.3.2 different speed with respect to load.The unit shall deliver

the rated capacity and in confirmation as per IS

18728:2024 and CPWD Specifications and work even at

50°C ambient temperature without tripping. The system

shall be able to deliver 100% of the rated capacity upto 39

°C. The unit shall be suitable to work on 400V +/- 10%, 3

Phase, 50Hz AC power supply and BMS compatible. The

unit shall be filled with first charge of the refrigerant and

ready for use as required. The condenser should be coated

with a hydrophilic film to prevent water accumulation on the

surface of the heat exchanger, enhance water dispersion,

31.3.2 10 reduce

HPrisk of degradation, thereby improving Per HP 24 ₹22,761.00 ₹5,46,264.00

Supplying, Installation, Testing and Commissioning of

following minimum capacity 4 way Cassette Type Indoor

ceiling mounted unit equipped with synthetic washable

media pre-filter, fan section with low noise fan/dynamically

balanced blower, multispeed motor, coil section with DX

Copper coil, electronic expansion valve, outer cabinet,

drain pump, grill, necessary supports, vibration Isolation,

Corded remote control etc., suitable for operation on single

phase 230 V ± 10%, 50Hz AC supply, complete, as

required. The Indoor units must shut down upon receiving

a singal from the BMS System/Fire Singnals. The system

shall be capable to adjust air flow as per room requirement

in auto mode. The cooling capacity of indoor unit will be at

MR Remote controllers & Reciever

Supply of cordless remote with Receiver Kit Nos. 5 ₹7,202.72 ₹36,013.60

Supplying, Installation, Testing and Commissioning of

31.13 Y/T/Multi Joints. Joints shall be of same Original Equipment

Manufacturer (OEM) make as of ODUs and IDUs

31.13.2 Outdoor Multi Joint Each 5 ₹8,098.00 ₹40,490.00

Digitally signed by AMIT

Refrigerant Piping

Supplying, Installation, testing and commissioning including

vaccumiazation and Nitrogen testing of following nominal

sizes of soft/hard drawn copper refrigerant piping for

31.14 VRV/VRF system, complete with fittings, with suitable

adjustable ring type hanger supports, jointing/brazing

including accessories, insulated with XPLE Class-O tubular

insulation/with Class-O closed cell elastometric nitrile

22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2

31.14.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 75 ₹739.00 ₹55,425.00

15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2

31.14.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 25 ₹346.00 ₹8,650.00

31.14.1 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 12 ₹256.00 ₹3,072.00

6 Drain Piping

Supply & Installation of rigid PVC piping complete with fittings, supports as per specifications and duly insulated

with 6 mm thick closed cell nitrile rubber insulation.

7 Control & Transmission Wiring for VRV unit

Supply & Installation of copper conductor transmission cum control wiring of different sizes in suitable conduits

between indoor and outdoor unit. With one no, MCB box.

8.1 Supply & Installation of Floor type MS fabricated Stand for outdoor units with rubber pads VRV. Nos 1 ₹12,390.00 ₹12,390.00

4.6 Cable Tray

Hot Dipped Galvanized Iron Cable Tray

Supplying and installing following size of perforated

Hot Dipped Galvanised Iron cable tray (Galvanisation

thickness not less than 50 microns) with perforation

not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with two

4.6.4 300 mm width X 50 mm depth X 1.6 mm thickness Meter 20 ₹1,062.00 ₹21,240.00

4.6.2 150 mm width X 50 mm depth X 1.6 mm thickness Meter 20 ₹803.00 ₹16,060.00

Digitally signed by AMIT

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing

drain pipe etc. and repairing the hole after insertion of drain pipe etc.

18.77 with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded Each 30 ₹452.00 ₹13,560.00

stone aggregate 20 mm nominal size), including finishing complete

so as to make it leak proof.

Digitally signed by AMIT

HVAC Low Side Boq ICMR KIDWAI, DELHI

S.No DESCRIPTION Unit Bill Qty Rate DSR Amount NDSR Amount

SUB-HEAD 'A' - EQUIPMENT

1 Air Handling Unit

Dismentling & ReShifting & Installation, testing and commissioning of double skin

airhandling unit ceiling suspended type complete with double skin housing with

EFF-1 motor, plug fan, cooling coil, filters.

2 Starter Panel

Supply, installation, testing and commissioning of AHU Starter Panel for 7500

CFM AHU complete with wiring etc. Nos 1 ₹64,900.00 ₹64,900.00

3 Supply, installation, testing and commissioning of 500 CFM INLINE FAN complete

with wiring etc. Nos 1 ₹19,470.00 ₹19,470.00

4 MS Chilled water Piping

30.2 Supplying, laying/ fixing, testing and commissioning of

following nominal sizes of chilled water piping inside

the building (with necessary clamps, vibration isolators

and fittings but excluding valves, strainers, gauges

etc.) duly insulated with following closed cell

elastomeric nitrile rubber of minimum 45 Kg / cu m

density, thermal conductivity 0.037 W/MK or better at

20 deg mean temperature class 'O' insulation applied

by suitable adhesive complete including repairing of

damage to building etc. as per specifications and as

required complete in all respect.

30.2.11 50mm dia(32 mm thick insulation) Rmt. 30 ₹1,859.00 ₹55,770.00

Supply, installation, testing and commissioning of Valves, Strainers of following

sizes duly insulated same as given for CHW pipe. as per specifications and

SITCof2/3way motorised valve complete with actuator, valve, power supply &

wired type thermostate

30.7.1 BUTTERFLY VALVE (MANUAL) with C I body SS

Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure

rating for chilled water/hot eater circulation as

Digitally signed by AMIT

Y - STRAINER of Ductile CI Body flanged ends with

stainless steel strainer for chilled / hot water circulation

including insulation as specified.

BALANCING VALVE WITH BUILT IN MEASURING

30.7.2 FACILITY with C I body flanged construction with

EPDM coated disc with long pitch with protected out

pipe insulation & PN 16 pressure rating for chilled / hot

water circulation as specified.

Digitally signed by AMIT

30.8 Supply, installation, testing and commissioning of Pressure Gauzes 4" dia Round

type complete with Syphon & fitting

30.9 Supply, installation, testing and commissioning of Temperature Gauzes 6" vertical

type complete with Syphon & fitting

6 Drain Piping

Supplying, laying, fixing, testing & commissioning of GI class 'B' pipes conforming

to IS: 1239 (Part-1, 1990) complete with all necessary fittings such as elbows,

tees, reducers etc and supports such as clamps etc. complete .Condensate drain

pipe should be complete insulation of 9 mm Nitrile.

25mm dia GI pipes ('B' class, for condensate drain) Rmt. 6 ₹1,475.00 ₹8,850.00

30.12 DUCTING, GRILLS,DIFFUSER AND INSULATION

Supplying, installation, balancing and commissioning

of factory fabricated GSS sheet metal rectangular/

round ducting complete with neoprene rubber

Thickness 0.63 mm sheet

Thickness 0.80 mm sheet

Thickness 1.00 mm sheet

Supply and installation of fire retardant duct thermal Insulation from inside duly

from factory (13 mm thick) applied with SR 505.

9 Duct Acoustic Lining

Supply & installation of duct acoustic lining with fibre glass insulation of density 32

kg/m3 covered with 26 Ga perforated Al. sheet with nuts and bolts complete as per

standards, requirement and drawings.

10 Grill / Diffuser

Supply, installation, testing and commissioning of aluminium powder coated

grills/ diffusers as per specifications and drawings.

Digitally signed by AMIT

30.15 Supplying, Fixing, installation, testing and

commissioning of powder coated extruded aluminium

Supply Air Grills with aluminium volume control Sqm 15 ₹9,623.00 ₹1,44,345.00

dampers in confirmation to SMACNA/IS and as per

specifications complete etc. as required.

30.17 Supplying, Fixing, installation, testing and Sqm 5 ₹12,841.00 ₹64,205.00

11 Collar Damper

Supply, installation, testing and commissioning of Alu. Collar Damper (supply vents

12 Canvas Connection Nos 1 ₹2,360.00 ₹2,360.00

13 Volume Control Damper (Duct Damper)

Supply & installation of extruded aluminium volume control damper with blades,

adjustable lever, frame etc. as per specifications and drawings.

Digitally signed by AMIT

SCHEDULE OF QUANTITIES: LIGHTING

S No Item Description Quantity Unit Rate NDSR Amount NDSR Amount

Supply, Installation, Testing and Commissioning of Pendant luminaire with HPE (High

Performance Efficiency) LED (Light Emitting Diode) system power: 22 W, Luminous

flux of luminaire 2200 lm,Colour temperature of 4000 K, Neutral white, CRI > 90,

SDCM 3, 230 V constant current driver, 70 % of luminous flux after 50,000 operating

hours, Energy efficient LEDs, Direct light emission, Luminaire profile in aluminium,

Polyester powder white coloured coat applied over a 5- stage pre-treatment, snap fit

prismatic diffuser for a homogenous light distribution, ZHLS (ZERO HALOGEN LOW

1 SMOKE) internal wiring, Electronic control gear, Sliding fixing wire suspension, 18 Nos ₹8,912.17 ₹1,60,419.13

Protection class I, IP 40, MacAdam 3, T.H.D ≤ 10%, driver efficiency ≥ 88%, surge

protection of 2.5 kV.

L=1175 mm, B = 52 mm, H = 64 mm, PL max = 1500 mm.

Supply, Installation, Testing and Commissioning of Pendant luminaire with HE-High

Efficiency LED (Light Emitting Diode) system power: 10W, luminous flux of luminaire

900 lm, colour temperature of 4000K, neutral white, CRI>90, MacAdam 3, T.H.D ≤

10%, driver efficiency ≥ 88%, surge protection of 2.5 kV, 230V constant current driver,

70% of luminous flux after 50,000 operating hours, direct light emission, curved

2 luminaire profile in aluminium, powder coated white, Prismatic diffuser for uniform 36 Nos ₹13,478.26 ₹4,85,217.39

illumination, Electronic control gear,

Protection class I, IP20

Supply, Installation, Testing and Commissioning of Pendant luminaire with HE-High

Efficiency LED (Light Emitting Diode) system power: 26W, luminous flux of luminaire

2080lm, colour temperature of 4000K, Neutral white, CRI>90, MacAdam 3, T.H.D ≤

10%, driver efficiency ≥ 88%, surge protection of 2.5 kV, 230V constant current driver,

3 70% of luminous flux after 50,000 operating hours, direct light emission, curved 4 Nos ₹22,281.74 ₹89,126.96

luminaire profile in Anodized aluminium, Prismatic diffuser for uniform illumination,

Electronic control gear

Protection class I, IP20, Ø = 600 mm, B = 55 mm, H = 75 mm, PL (max) = 1500 mm.

Supply, Installation, Testing and Commissioning of Cove mounted LED strip (flexible),

with 60 LEDs per meter, 2835 SMD package with a thermal tape of high thermal

convection factor, system power: 6W/ meter, luminous flux 300 lm, colour temperature

of 4000 K, Neutral White, CRI > 80, 12 V DC, constant voltage driving circuit,

Electronic control gear,

Protection Class II, IP20, THD<15%, Driver efficiency>88%, Surge proetction of 2.5kV

Supply, Installation, Testing and Commissioning of LED suspended Mounted

decorative UP-DN 50 UP - 88 DnW Efficacy: 105lm Lumen: 6500lm Up - 9,680 lm

Down, Unique wing shape design, CRI>90, MacAdam 3, T.H.D ≤ 10%, driver efficiency

≥ 88%, surge protection of 2.5 kV, Color Temperature: 4000K SDCM 3 Life Time: L70

50000Hrs 230V Light Throw: Direct-Indirect light emission Material: Aluminium Optics:

Opal Diffuser Finish: White Control Gear: Electronic Control

Protection Class: I IP 20, L: 2349mm mm H: 136mm

Digitally signed by AMIT

Supply, Installation, Testing and Commissioning of recessed LED panel luminaire

suitable for installation in 600 × 600 mm modular ceiling grid, with LED (Light Emitting

Diode) system, system power: 36–40 W, luminous flux of luminaire ≥ 3600–4000 lm,

colour temperature of 4000 K, Neutral White, CRI > 80, 230 V AC electronic constant

current driver, 70% of luminous flux after 50,000 operating hours, uniform direct light

8 emission, aluminium / CRCA housing with white powder-coated finish, opal 5 Nos ₹3,478.26 ₹17,391.30

polycarbonate diffuser, polyester white powder coat applied over 5-stage pre-

treatment, beam angle 110°–120°, UGR < 19 suitable for office applications, external

electronic control gear, Protection Class II, IP20, complete with all mounting

accessories, internal wiring, testing and commissioning.

"Supply, Installation, Testing and Commissioning of COB-based recessed Low Height

downlight luminaire Amber, System power: 15W, Luminous flux of luminaire 1350lm,

Colour temperature of 4000K, Neutral White, CRI>90, MacAdam 3, T.H.D ≤ 10%,

driver efficiency ≥ 88%, surge protection of 2.5 kV, 230V constant current driver, 70%

of luminous flux after 50,000 operating hours; Energy-efficient COB, Direct light

emission, Luminaire housing in aluminium, Polyester powder White coloured coat

9 applied over a 5-stage pre-treatment, anti-glare black reflector with 60 degree beam 100 Nos ₹2,785.22 ₹2,78,521.74

angle, UGR,19, ZHLS (ZERO HALOGEN LOW SMOKE) wiring, Electronic control

Protection class II, IP 40, Ø = 93 mm, Ø(Cut Out) = 85 mm, H = 60 mm.

Providing and fixing decorative wooden slatted feature panel above reception counter,

made of CNC-cut engineered wood fins with uniform spacing and finished in approved

veneer/laminate.

10 Including complete framework, supports, fixing, finishing and alignment as per 4 Nos ₹16,350.00 ₹65,400.00

approved design and site requirement.

Providing & fixing decorative wall-mounted LED wall light with wooden finished back

panel and recessed niche, complete with inbuilt warm white LED, driver, wiring and

mounting accessories.

11 Including installation, testing and commissioning as per approved drawings and site 5 Nos ₹7,500.00 ₹37,500.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES FOR SUPPLYING, INSTALLATION, TESTING & COMMISSIONING OF STRUCTURE CABLING, IP-PBX, LAN, Wi-Fi, LAN SECURITY, CCTV SYSTEM, FA-PA SYSTEM AND ACCESS

Description of Item NDSR

S. No Unit Qty DSR Rate NDSR Rate(Rs.) DSR Amount

DSR/NDSR SECTION - I- STRUCTURED CABLING SYSTEM PASSIVE

Supplying, drawing, Testing and commissioning of Cat6A UTP 4 pair, 23 AWG solid

copper cable in existing conduit/ on surface, U/FTP, LSZH, Non- Plenum, Horizontal

(solid) Cable suitable for high speed data networking application supporting upto

10Gbps over a 100 meter channel. The 4 Unshielded Twisted Pairs (UTP) cable with

color coded insulation for easy indentification should have FLAME PROPERTIES i.e.

Flammability Test - IEC 60332-1, Smoke Density - IEC 61034, LSZH standards

compliance: ANSI/TIA-568 C.2, ISO/IEC 11801, IEEE 802.3an, RoHS. Delay Skew should

be < 45NS. The outer Cable Diameter should be 7.5 + 2 mm. Cable should have been

tested and verified by UL/ ETL etc. complete as required.

Supplying, Installation, Testing and commissioning of

RJ45 Connector for CAT 6/6A Cables. RJ45 modular plug supports 4 twisted pairs, 8 Each 75 9

positions, 8 connectors. Housing: PC, UL94V-2, transparent color, Use for 24- 26 AWG

stranded wires etc. complete as required.

Supplying Installation Testing and Commissioning of 24 port Cat6 Patch Panel loaded.

Must be of 1U height with clear label holders and white label with the panel. 24 Ports Each 4 5278

Cat-6 Patch Panel should have ETL/UL verification program certificate for compliance

with ANSI/TIA-568.2-D etc. complete as required.

Supplying, Installation, Testing and commissioning of following CAT6A Patch Cord

4 39.13 should have ETL/UL verification program certificate for compliance with ANSI/TIA-

568.2-D etc. complete as required.

39.13.1 Copper Patch Cords of length 1m (3ft) Each 75 173 12,975.00

5 39.13.2 Copper Patch Cords of length 3m (10ft) Each 75 405 30,375.00 -

Supplying, Installation, Testing and commissioning of

CAT6A Copper Information Outlet (IO) with face plate

of color as per site requirement, should have ETL/UL verification program certificate

for compliance with ANSI/TIA-568.2-D. All copper Cable and Components should be

from same OEM to maintain compatibility and interoperability etc. complete as

Digitally signed by AMIT

Supplying and fixing 24U Rack with 4 inch Castor wheels and front brake Floor

Standing Rack with Main Frame Pillar of 1.25mm Powder Coated CRCA Sheet with

removable side panels, L- Shape adjustable Vertical Mounting Rail of 2mm with

'U'Marking completely knocked-down condition (CKD) Shape, fitted with 4 number

cooling fans, minimum 5nos two line cable entry/exit provision at top and bottom

with rubber protection, Front door 5mm Toughened Glass with MS frame or MS

perforated with lock, Rear MS vented or perforated door, Powder coated Color- RAL-

7035 or black, complied with UL & RoHS, 2 x 6 sockets 16A power distribution

units, 3 numbers closed cable organizer, Hardware mounting screws packet of 20 x 1

number, etc. complete as required.

Digitally signed by AMIT

SCHEDULE OF QUANTITIES FOR SUPPLYING, INSTALLATION, TESTING & COMMISSIONING OF STRUCTURE CABLING, IP-PBX, LAN, Wi-Fi, LAN SECURITY, CCTV SYSTEM, FA-PA SYSTEM AND ACCESS

CONTROL SYSTEM PROJECT : ICMR

Description of Item NDSR

S. No Unit Qty DSR Rate NDSR Rate(Rs.) DSR Amount

SECTION - II- IP-PBX SYSTEM

Supplying, installation, testing and Commissioning of IP based voice communication

system with 04 Port Voicemail, 04 Port FXS, 04 Port FXO, 1 PRI Trunk lines (30

Channels) Circuit with CLIP Facility, min 100 IP users License with provision for further

1 38.1 additions, 100 analog users, 01 Number IP based Operator Console, 100 Party Set. 1 1578920 15,78,920.00 -

Conference, Speed Dial, Music on Hold, Internal/ External ring difference, Call Barring,

Call Pickup, Redundant server in active -Active mode and as per technical

specification including supporting accessories etc complete as required. The system

should have valid TEC GR approval from DoT.

Supplying, Installation, Testing & Commissioning of Type 1 IP Phone having 2 VoIP

2 38.3 account, 120 x40 DOT matrix screen with backlight, Full HD duplex speaker phone, Nos. 30 11698 3,50,940.00 -

IPV6, Gigabit Etherent, PoE etc. complete as required.

Supply, Installation, Testing & Commissioning of Type 2 IP Phone with 2 Voip

3 accounts, 2 Lines , HD Voice,Graphic LCD display with backligh. Nos. 5 23,760.00 1,18,800.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES FOR SUPPLYING, INSTALLATION, TESTING & COMMISSIONING OF STRUCTURE CABLING, IP-PBX, LAN, Wi-Fi, LAN SECURITY, CCTV SYSTEM, FA-PA SYSTEM AND ACCESS

CONTROL SYSTEM PROJECT : ICMR

Description of Item NDSR

S. No Unit Qty DSR Rate NDSR Rate(Rs.) DSR Amount

SECTION - III- LOCAL AREA NETWORK ( LAN )

Supply, Installation, Testing & Commissioning of 24 x 100M/1G RJ45 PoE/PoE+ ports

with 4 x 1G SFP/10G SFP+/25G SFP28. PoE+ switch with min 370 Watt PoE+ budget

.Should have RPS option from day 1. Switching capacity of 240 Gbps Gbps, forwarding

performance 180 Mpps, Should support up to 32K MAC addresses or more. Should

have Static Routing, RIP, VRRP, OSPF, OSPFv3, BGP,BGP4+,MPLS from day 1, Should

support ISSU from day 1, should support physical stacking of more then 8 per stack,

Neighbour discovery, system logging, Telnet, SSH, SNMP, Network Time Protocol

(NTP), IPv6 features from day 1, MTBF Min 198000 Hr

Supply, Installation, Testing & Commissioning of Access Point 4x4:4 + 2x2:2 streams

SU/MU MIMO on 5GHz and 2.4GHz,AP should have one Ethernet port and one 2.5Gig

port, should support IEEE 802.11 a/b/g/n/ac/ax amendments. AP should provide 23

dBm EIRP on 2.4GHz and 5 GHz, -93 dBm on 2.4GHZ and -98 dBm on 5GHZ receive

sensitivity. AP should have capacity to handle minimum 500 Concurrent devices.

3 Should have IPv6 support, IEEE 802.1Q, Band balancing, airtime fairness. AP Should Nos. 2 81,821.00 1,63,642.00

support auth/encryption methods for WLAN configuration: Open, WEP, WPA2-AES,

Unique PSK, WPA3-SAE, WPA3-OWE, IEEE 802.1X/EAP, AAA, AES-GCMP-256. AP

should be having administration access through HTTPS GUI, SSH CLI, Should have

operating temperature of 0-40 ºC

Supply, Installation, Testing & Commissioning of Firewall 2x10/100/1000 Base T ports

with 2x 100/1000 SFP Ports in Combo ,Mion 1 x10 Gbps ports either in Copper or

Fiber , Min 4 Gbps L2/L3 Throughput, Min concurrent session 2 million, Min 1 x set of

Bypass Ports , Min 1x USB ports , Should have dual AC power supply from day 1 . Nos. 1 13,89,600.00 13,89,600.00

Firewall, Switches, Wireless Components , Fiber module should be from the same

OEM for seamless integration.

Digitally signed by AMIT

SCHEDULE OF QUANTITIES FOR SUPPLYING, INSTALLATION, TESTING & COMMISSIONING OF STRUCTURE CABLING, IP-PBX, LAN, Wi-Fi, LAN SECURITY, CCTV SYSTEM, FA-PA SYSTEM AND ACCESS

CONTROL SYSTEM PROJECT : ICMR

Description of Item NDSR

S. No Unit Qty DSR Rate NDSR Rate(Rs.) DSR Amount

SUB-HEAD -IV- IP CCTV SYSTEM

Supplying, drawing, Installation, Testing and commissioning of CAT6 UTP LSZH 23AWG

Twisted 275 DELHI SCHEDULE OF RATES (E&M)-2025 Pair Cable in existing conduit/ on

surface, Category 6 Unshielded Twisted Pair, 4 pair should be complied as per UL/ETL

1 39.17 verification program for compliance with ANSI/TIA-568.2-D standard. Outer diameter

should be in the range of 6.1mm nominal with Operating Temperature Range : -5° to

+60°C, Bending Radius : < 4 X Cable Diameter at –5°C ± 1°C and Pulling Force: 11.5Kg

etc. complete as required.

Supplying, Installation, Testing and commissioning of

2 RJ45 Connector for CAT 6/6A Cables. RJ45 modular plug supports 4 twisted pairs, 8 Each 5 9

positions, 8 connectors. Housing: PC, UL94V-2, transparent color, Use for 24- 26 AWG

stranded wires etc. complete as required.

Supplying Installation Testing and Commissioning of 24 port Cat6 Patch Panel loaded.

3 Must be of 1U height with clear label holders and white label with the panel. 24 Ports Each 1 5278

Cat-6 Patch Panel should have ETL/UL verification program certificate for compliance

with ANSI/TIA-568.2-D etc. complete as required.

Supplying Installation Testing and Commissioning of 24 port Cat6 Patch Panel loaded.

Must be of 1U height with clear label holders and white label with the panel. 24 Ports Each 4 5278

Cat-6 Patch Panel should have ETL/UL verification program certificate for compliance

with ANSI/TIA-568.2-D etc. complete as required.

Supplying, Installation, Testing and commissioning of following CAT6A Patch Cord

4 39.13 should have ETL/UL verification program certificate for compliance with ANSI/TIA-

568.2-D etc. complete as required.

39.13.1 Copper Patch Cords of length 1m (3ft) Each 5 173 865.00

5 39.13.2 Copper Patch Cords of length 3m (10ft) Each 5 405 2,025.00 -

Supplying, Installation, Testing and commissioning of

CAT6A Copper Information Outlet (IO) with face plate

6 39.15 of color as per site requirement, should have ETL/UL verification program certificate Each 5 302 1,510.00 -

for compliance with ANSI/TIA-568.2-D. All copper Cable and Components should be

from same OEM to maintain compatibility and interoperability etc. complete as

Digitally signed by AMIT

4MP IP IR Dome Camera

40.3 Supplying Installation Testing and Commissioning of

4MP IP IR Dome Camera having following

specifications and features etc :-

1) Signal System: PAL/NTSC, Signal to Noise Ratio: >

50 dB,Camera should display Camera title, Date &

Time in live & recorded video

2)Image Sensor: 1/2.8" or better progressive Scan

CMOS to get color image even at night

condition(Minimum Illumination: 0.006 Lux@ F1.4,

AGC ON, 0 lux with IR or better) True Day & Night

High Performance Mechanical IR cut filter with auto

switch, Integrated IR Source (Auto, Manual)- Inbuilt IR

LED's with effective distance upto 50 meter or better

and 30 meter for colour view in night, Imaging: 1/3s to

1/30000s electronic shutter support, Auto Gain Control

, White Balance- Auto, Back Light Compensation,

Multi zone Privacy Masking, HLC, Digital

3) Compression (Minimum): Video:- H.265 or better,

Audio:- G.711U/A, G.711Mu, G.726, AAC, G.723

4) Wide Dynamic Range:- WDR (120dB or more)

5) Digital Noise Reduction:- DNR (3D) On/Off

6) Video Streaming & Frame Rates :- Triple streaming

, configurable Main stream: 4MP (2560×1440)25/30fps

, Sub streams minimum: 720P@25/30 fps

7) Image Setting: Rotate Mode, saturation, brightness,

contrast, sharpness adjustable through client software

or web browser, Edge Analytics: Tripwire, Intrusion,

Motion Detection

4MP Security: AES 256-bit

@ 25/30fps@1440P Encryption,

(2560x1440) Dome Camera with 2.7 to 4 mm ~12 to

13.5mm or better Varifocal Motorized lens.

Digitally signed by AMIT

Network Video Recorder (NVR)

40.10 Supplying Installation Testing and Commissioning of

following Channel Network Video Recorder (NVR)

with camera licenses to record for all channels having

specifications and features etc as mentioned below :

1) Network Video Recorder Embedded/ Installed OS

(Linux) along with Camera Licenses for number of

channels of NVR to record per NVR and to provide a

live view, storage and simultaneously Multi-channel

playback of all IP, IR camera or more and must be

ONVIF with minimum support of 256Mbps incoming

2) NVR should support H.265 or better, H.264,

MJPEG, MPEG4 support

3) Must support 1 channel Input, 1 channel Output,

RCA for Two-way Talk

4) Intelligent auto power on when power resumes after

5) Storage: It should support minimum 2 SATA Slots

with 16TB capacity/ Slot.

6) Connectivity Interface : 1 Nos. x 10/100/1000 Mbps

Ethernet Ports, 1x RS485, 1x RS232

7) Backup Interface : Its should have 2 Nosx USB port

(1x USB3.0, 1xUSB2.0)

8) Video Output Ports: 1x HDMI and 1 VGA

9) Alarm Ports: It should have 4/1 Ch In/ Out ports to

connect various type of external sensors and output

devices like hooter/ Siren etc.

10) Email & SMS Altert options: Option for SMS/ Email

Alerts to minimum 5 designated mobile number for

Channel HDD failure,

Network Video vandalism, tempring,

Recorder (NVR) having

40.10.2 display split :- Main screen: 1/4/8/9/16, 2nd screen: Nos. 1 12799 12,799.00

Supply, Installation, Testing & Commissioning of 16TB Surviellance Hard Disk.

Supply, Installation, Testing and Commissioning of Full HD 55" LED Professional

10 Display Panel. Nos. 1 85,500.00 85,500.00

Digitally signed by AMIT

Supply, Installation, Testing & Commissioning of L2+ managed industrial PoE switch

with 10*10/100/1000M RJ45 ports and 4*100/1000M uplink SFP slot ports, Port 1-8

can support IEEE802.3af/at PoE. Support DC dual power supply input and DIN rail

mounting. Switching capaticy of 256 Gbps, forwarding performance 20.83 Mpps,

11 having 8 x 10/100/1000BASE-T PoE-plus(RJ45) with maximum PoE output power is Nos. 1 1,13,000.00 1,13,000.00

120W(at-240W). , with 2*10/100/1000Base-T uplink RJ45 ports 4*100/1000Base-X

uplink SFP slot ports., 8K MAC address. Should have Static Routing , system logging,

Telnet, SSH, SNMP, Network Time Protocol (NTP), and IPv6 features from day 1.

Supply, Installation, Testing and Commissioning of Workstation PC: Intel(R) Core(TM)

i7-3770 Processor (8M Cache, up to 3.90 GHz); RAM: 8GB (1x8GB) Non-ECC DDR3

1600MHz ; Keyboard: 12 function keys; Chassis: Tower/Workstation; DVD: 8X Slimline

12 DVD+/-RW, Data Only; Dual Graphics Card; Network interface card: Integrated Nos. 1 1,25,000.00 1,25,000.00

Intel(R) 82579LM Gigabit1 Ethernet LAN 10/100/1000; Hard disk: 250GB, 7200 RPM

3.5" SATA 6Gb/s Hard Drive; Operating system: Windows 7 Professional 64 Bit or

Digitally signed by AMIT

SCHEDULE OF QUANTITIES FOR SUPPLYING, INSTALLATION, TESTING & COMMISSIONING OF STRUCTURE CABLING, IP-PBX, LAN, Wi-Fi, LAN SECURITY, CCTV SYSTEM, FA-PA SYSTEM AND

ACCESS CONTROL SYSTEM PROJECT : ICMR

Description of Item DSR NDSR

S. No Unit Qty DSR Rate NDSR Rate(Rs.)

Amount Amount(Rs.)

SECTION -VI- ACCESS CONTROL SYSTEM:

Supply ,Installation ,Testing & Commissioning of 4 Door 4 reader access

control panel with with buttons for entering and reading cards and

exiting the door, Large capacity of 24,000 users, 100,000 offline storage

records. TCP/IP high-speed communication, convenient LAN and WAN

1 wiring, The card reader can be connected to the international standard Nos. 1 95,000.00 95,000.00

Wiegand 26bit-34bit Powerful functions. In addition to the access

control function, the software also presents attendance, online patrol,

conference sign-in, fixed consumption, WEB mother card function, and

more cost-effective.

Supply, Installation , testing and commissioning of 12 V SMPS DC Power

2 Supply Unit, highly regulated and spikes free terminal voltage and heavy Nos. 1 7,500.00 7,500.00

sourcing current for regulated terminal voltage.

Supply & Installation of Operation system: Windows xp and the upward

system, such as: Windows 2000 、Windows

XP 、 Windows7、Windows Vista、windows nt、Windows 2000

sever、Windows 2003 、Windows Server 2008 and so on Database :MS

3 Access (the default database after installation is the bringing small Set. 1 1,25,000.00 1,25,000.00

database of operating system) MS SQL Server (suggest more than 200

people, or swiping card every day more than 1000 records, had better

choose to use this article database.)

Supply, Installing, Testing & Commissioning of fingerprint, IC/ID swipe

card Fingerprint capacity: 1000 pieces Short Range Multi Technology

4 Smart Card Reader UL Listed For Exit of Lift Access Doors, tripod/Flap Nos. 4 12,500.00 50,000.00

barrier- Entry & Exit (doors) as per the specification, with back plate &

Supply ,Installation ,Testing & Commissioning of Smart Card Contactless

transmission of data and supply energy (No battery needed), Operating

5 Distance: Upto 100mm (Depending on Antenna Geometry), Operating Nos. 10 320.00 3,200.00

Frequency: 13.56 MHZ.

Supply ,Installation ,Testing & Commissioning of Electromagnetic Lock

6 600 lbs, Single leaf, LED Status Display, Nos. 4 4,980.00 19,920.00

Supplying, drawing, Installation, Testing and commissioning of CAT6 UTP

LSZH 23AWG Twisted 275 DELHI SCHEDULE OF RATES (E&M)-2025 Pair

Cable in existing conduit/ on surface, Category 6 Unshielded Twisted

Pair, 4 pair should be complied as per UL/ETL verification program for

7 39.17 compliance with ANSI/TIA-568.2-D standard. Outer diameter should be

in the range of 6.1mm nominal with Operating Temperature Range : -5°

to +60°C, Bending Radius : < 4 X Cable Diameter at –5°C ± 1°C and Pulling

Force: 11.5Kg etc. complete as required.

Supply and Laying of 8 Core x 1.0 sq mm multi strand, copper,

8 unarmoured shielded Cable as per specification (between the every 60 210.00

card readers & the access controllers)

Supply and Laying of 4 Core x 1.0 sq mm multi strand, copper,

9 unarmoured shielded Cable as per specification (between the every 120 160.00

card readers & the access controllers)

Supply ,Installation ,Testing & Commissioning of U/L Clamp made of

10 aluminium anodised for EM Lock. Nos. 4 2,300.00 9,200.00

Supply , Installation , Testing and commissioning of Exit push button as

S.No. Item Description Qty. Unit Rate Amount

Conference Room (2 nos) :-

Supply, installation, testing & commissioning of 6" Two way Coxial ceiling speaker with 30 Watts Rated Power

or better, 45W Max Power or better, Transformer taps: 30 W ,15 W ,7.5 W; Frequency Range (-10 dB) 70 Hz -

20 Khz or better , Opening Angle 173˚ ; Sound pressure level: 89 dB or better, 6" Driver size, Tweeter: 0.5",

1 Ceiling Speaker Should have Support EN-60065 Safety . 4 Nos 5,569.00 ₹22,276.00

Supplying, Installation, testing and commissioning of passive column loudspeakers with Power handling

(continuous) :100 W; Power handling (program) :200 W; Frequency range : 70 Hz – 15,000 Hz; Maximum sound

pressure: 122 dB; sensitivity :90 dB ; Coverage angle HxV : 130° x 20°; Nominal impedance : 8 Ω; Transformer

taps 70 V : 60 W, 30 W, 15 W, 8 W, 4 W; Transformer taps 100 V : 60 W, 30 W, 15 W, 8 W ; Transducer: 6 x

2 2.5" full range driver ; IP rating: IP55c; with Included Tilt + Pan Bracket hardware. 2 Nos 75,423.00 ₹1,50,846.00

Supplying, Installation, testing and commissioning of Multi Channel Class D amplifier providing total rated output

power 600 W or better; Minimum 4 Channel Input and 4 channel Output, Nominal Gain 36.2 dB or better ,

Signal to Noise Ratio > 103 dB or better, Damping factor : > 1000 or better; THD+N < 0.1 % or better, 2 x 6-pin

Euroblock, 3.81 mm, male, parallel 1x RJ45, Audio limiters, high temperature, DC, HF, short circuit, back-EMF,

peak current limiters, inrush current limiters, mains over/under voltage protection.

Supply, Installation, testing and commissioning of 6x4 Digital Matrix Processor DSP with 6 mic/line inputs and 4

line outputs; Six channels of AEC; AUDIO SYSTEM should include a configurable USB Audio interface- output

configuration of the USB Audio Interface can be set to 0x8, 2x6, 4x4, 6x2, or 8x0 ; should be certified for

microsoft Teams and Zoom, 24 x 48 Dante enable audio networking & AES67 support; 64 bit floating point

audio DSP processing; Equipped with selectable 48 volt phantom power for the analog inputs; Should have 24

bit/48 kHz analog to digital and digital to analog converters; 8 or more DSP Configurator presets; Audio system

gain: Balanced output: 0 dB, unbalanced output: -6 dB or better; Frequency response: 20 Hz to 20 kHz, ±0.2 dB

4 or better; THD + Noise <0.02%, S/N: Analog In to Analog Out >109 dB, Analog In to Digital Out 110 dB, Digital 1 Nos 3,75,123.00 ₹3,75,123.00

In to Analog Out 115 dB, Crosstalk should be <-90 dB, impedance >10k ohms; Up to eight audio file players

can be used to play back audio files;

Digitally signed by AMIT

Supply, Installation, Testing & Commissioning of Ceiling Microphone tile with Min of 24 x Pre-polarized

condenser capsule or higher, Support upto 80 m² coverage Distance ; AF frequency response 160 Hz - 18,000

Hz or better; Sound pressure level : Max. 104 dB SPL or better, Sensitivity 0 dBV/Pa or better; Dynamic range

93 dB(A) or better, Signal-to-noise ratio 83 dB (A) or better; Should have Adaptive beamforming technology ,

Ceiling Tile Audio output : 1 x 3-pin terminals ; 2 x Digital Dante Network Audio or better, Should have Exclusion, Priority

Microphone Zones feature, complete with standard accessories.

Supplying, Installation, testing and commissioning of 75" 4K UHD(3840 X 2160) Slim DLED display, Aspect

Ratio 16:9 or better, Brightness 500 Cd/m2 or better, Contrast Ratio : 1200:1 or better, Haze 28% or

better,Viewing Angle 178° or better, Android OS, Quad-Core ARM Cortex-A55 CPU, ARM Mali-G51 MP2 GPU,

4GB DDR4 memory, 32GB storage, HDMI IN X 2, HDMI Output x 1 ,USB 2.0 X 1 ,USB 3.0 X 1 , RS232 X 1,

RJ45 X 2(IN/OUT), USB Type-C X 1 , Should have Support wifi feature, Should have built-in 24W speaker,

Operation time: 24/7, Operation Temperature:0℃ - 45℃, Operation Humidity: 10% - 90% , complete with

standard accessories.

Supplying, Installation, testing and commissioning of 55" Digital Signage Standy with 3840 x 2160 Resolution or

better ; Aspect Ratio : 16:9 or better; Brightness : 350 cd/m2 or better ; Pixel Pitch : 0.246mm × 0.246mm; View

Angle : H: 178° V: 178° or better ; Response : 8ms or better ; Contrast Ratio : 1200:1; or better ; Color : 16.7

Million or better ; Should have Bulit-in 2 x 8Ω, 10W Speaker; Android OS : 11 ; RAM : 2GB or better; Storage :

16GB or better ;Connection Interface : 1 x LAN, 2 x USB, 1 x mini USB, 1 x Earphone; Should have WIFI 2.4G,

1 x Bluetooth ; Should have support Video RM, RMVB, MKV, TS, FLV, AVI, VOB, MOV, WMV, MP4 Picture :

JPG, BMP Audio : MP3, WMA, APE Media Format ; Should have support Free Split Layout, Network

55" Digital Signage Management, Multiple play modes with customization , Firmware, Remotely control and manage one or more

Standy screens , Remote program release and local (USB) program update ; Users can activate and set initial

password ; Should have Software to manage <200pcs Players as per requirement.

Supply, Installation. testing and Commissioning of Cable Cubby or cable management box with flip-open cover

Cable management having 2x HDMI, 1x universal power, 1 x USB-A Mobile Charger, 1 x USB Type -C, 2x CAT 6A with 6 pass-

8 through slots. 2 Nos 19,125.00 ₹38,250.00

Digitally signed by AMIT

Supply, Installation, Testing & Commissioning of Full HD IP PTZ Camera supporting 1080p at 60 Frames per

Second, minimum 12X Optical Zoom with FoV of minimum 72.5° horizontal and minimum 256 presets.

Camera should support simultaneous outputs through HDMI, USB 3.0 & Ethernet, Audio In and controllable via

RS232, Ethernet, USB 3.0. Panning angle -170° ~ +170° , Tilting angle -30° ~ +90.Support Focus System/Gain

9 PTZ Camera control/White balance/Exposure control:Ato/Manual. Camera should support RTSP, RTMP , RTMPS , SRT & 1 Nos 1,45,444.00 ₹1,45,444.00

should be compatible with Virtual USB Driver.

Supply, installation, testing & commissioning of Keypad cum controller with Two bidirectional RS-232 ports; Two

relays for controlling room functions; One IR port for connecting up to two emitters; One digital input; SDRAM:

10 Controller 512 MB; Flash: 512 MB, complete with standard accessories as required. 1 Nos 1,90,555.00 ₹1,90,555.00

Supply, Installation, Testing & Commissioning AVoIP Encoder supports 4K UHD over Gigabit Ethernet; Inputs

min 2x HDMI 2.0 4K60 4:4:4 & 1x USB-C capable of scaling and outputting video with auto-switching between

all the 3 input sources; HDCP 2.3; HDMI Loop Out up to 4K60 4:4:4; USB Host port; LPCM audio support upto 8

Channels from HDMI Input; Embedded audio input; Native AES67 Network Audio; Adjustable Video Bitrate upto

800 Mbps with bit-rate compression CODEC w/ built-in AI; Video Codec: JPEG2000 based visually lossless

video compression algorithm; latency: 5 ms at 4K60 4:4:4; AES-256 Encryption or better; 2 or more LAN ports

11 Encoder with POE power sharring;; VLAN tagging to saperate Video traffic from data & voice and VLAN Trunk mode 3 Nos 1,45,000.00 ₹4,35,000.00

capability; RTP audio stream capability; ICMP,IGMP & PIM feture support; Supports Video, Audio, USB, KVM &

RS232 independent matrix routing; EDID managment; USB over IP (KVM), RS-232 over IP, IR over IP, GPIO

over IP; Standard PoE Power 15 W or lower; Integrated Software management platform supports for system

monitoring & control; Future upgradable DANTE; support 802.1x, HTTPS, SSH security encription;

Supply, Installation, Testing & Commissioning AVoIP Decoder supports 4K UHD over Gigabit Ethernet; Outputs

min 1x HDMI 2.0 4K60 4:4:4 & 1x USB-C capable of scaling and outputting video with auto-switching; HDCP

2.3; min 2x USB peripheral ports; LPCM audio support upto 8 Channels from HDMI Input; De-embedded audio

output; Native AES67 Network Audio & Dolby enabled; Adjustable Video Bitrate upto 800 Mbps with bit-rate

compression CODEC w/ built-in AI ; Video Codec: JPEG2000 based visually lossless video compression

algorithm; latency: 5 ms at 4K30 & 4K 60 4:4:4; 2 or more LAN ports with POE power sharring; VLAN tagging to

saperate Video traffic from data & voice and VLAN Trunk mode capability; RTP audio stream capability; Built-in

12 Decoder 16x16 videowall function with rotation support upto 270 degree; Text overlay capability; ICMP,IGMP & PIM feture 2 Nos 1,40,000.00 ₹2,80,000.00

support; Auto Video Scaler 4K in/1080P out & 1080P in/4K out; Supports Video, Audio, USB, KVM & RS232

independent matrix routing ; USB over IP (KVM), RS-232 over IP, IR over IP, GPIO over IP and CEC over IP;

Standard PoE Power 15 W or lower; Integrated Software management platform supports for system monitoring

& control; Future upgradable DANTE; support 802.1x, HTTPS, SSH security encription;

Digitally signed by AMIT

Supply, Installation, Testing and Commissioning of 24x1G PoE+ 300W power budget, 2x1G and 4xSFP

Managed AV over IP network Switch, support for dante, av over IP, AES67, and AVB profiles. 64 Gbps

Switching, 16 Mb Packet Buffer, latency <2.15.µs 1G, 512 IPv4 & 128 IPv6 IP Multicast Routing Entries, 4K

VLANs, 60 Gbps non-blocking fabric across 30 ports, USB-C and RJ45 RS232 console ports and USB-A

13 Network Switch

storage port, Auto-Trunk, Auto-LAG and IGMP Plus, IGMPv3 MLDv2 Snooping, Proxy ASM & SSM. complete.

Supply, Installation. testing and Commissioning of 13th Gen core i5,8 Gb RAM, 512 GB HDD Workstation PC

14 Workstation PC with keyboard & Mouse. 1 Nos 75,000.00 ₹75,000.00

CABIN Room (6 nos.):-

Supplying, Installation, testing and commissioning of 43" Display with 4K Resolution; Aspect ratio : 16:9 or better

; Brightness 400 Cd/m2 or better; Contrast ratio: 1200:1 or better ; Response time :8ms or better; Viewing angle

:178°(H)/178° (V) or better ; CPU: Cortex-A55 x4,1.3 GHz; GPU: Mali-G31 MP2; Android 11.0; RAM : 2.0 GB

DDR3, 16 GB Memory Flash, Wifi Type support both 2.4 & 5G Standard, Dolby Audio,HDR 10, Built in Wifi and

Cromecast, HDMI CEC, HDMI ARC, Built-in Bluetooth, Hotel mode, Meeting Mode; Should have interfaces:RF

15 43" Display IN X 1, AV IN : 1mini *Side; USB INPUT 2.0 X 1,USB INPUT 3.0 X 1 ,HDMI X 3; RJ-45 X1; SPDIF OUT: yes; 6 Nos 48,552.00 ₹2,91,312.00

Should have Built in 20 W speaker ; Should have 24/7 operation hour ; with included Remote Control, Power

Cord, complete with standard accessories.

Supply, Installation. testing and Commissioning of Cable Cubby or cable management box with 1x HDMI, 1x

Cable management universal power, 1 x USB-A Mobile Charger, 1 x Type-C USB , 1x CAT 6A.

Workstation Area (20 + 3 Pax):-

Supply, Installation. testing and Commissioning of 13th Gen core i5,8 Gb RAM, 512 GB HDD Workstation PC

17 Workstation PC with keyboard & Mouse, 22-24" monitor. 23 Nos 80,000.00 ₹18,40,000.00

Cable & Connector

Supply, Installation, testing & Commissioning of 2 core 16 AWG/1.5 Sq mm, Twisted, unshielded Speaker cable

with stranded annealed bare copper conductors, Semi-rigid PVC insulation, NEC CL3R, CEC CMG,

18 Speaker Cable 150 Mtr 139.00 ₹20,850.00

Supply, Installation. testing and Commissioning of 10 meter High‐Speed Active HDMI Cable with Gold‐Plated

connectors; video capability: 4K@60Hz 4:4:4 18Gbps; video complaince support- HDMI 2.0, HDCP 2.3, HDR;

19 HDMI Cable Should have CEC Support; Cable Construction- Solid Core Oxygen Free Copper 6 Nos. 14,492.00 ₹86,952.00

Supply, Installation. testing and Commissioning of 2 meter High‐Speed Active HDMI Cable with Gold‐Plated

connectors; video capability: 4K@60Hz 4:4:4 18Gbps; video complaince support- HDMI 2.0, HDCP 2.3, HDR;

Should have CEC Support; Cable Construction- Solid Core Oxygen Free Copper Compliant, REACH

Digitally signed by AMIT

Supply, Installation, testing & Commissioning of 4 Pair Shielded Cat 6 LAN Cable, complete with standard

21 Cat 6 Cable UTP accessories as required as per tender specifications. 150 Mtr 80.00 ₹12,000.00

Supply, Installation, Testing & Commissioning of 12U AV equipment rack for the backend equipment, should

have Front glass door, heat dissipation, power distribution unit complete with standard accessories as required

Supply , Installation, testing & commissioning of Fixing Connectors and Accessories for audio & Video system

23 Cable & Connector complete as required. 1 Lot 25,100.00 ₹25,100.00

Total with TAX ₹54,16,719.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - FIRE ALARM

S NO DSR/MR DESCRIPTION UNIT RATE AMOUNT AMOUNT

DSR 2025 DSR RATE NON DSR

SITC of UL268 10th edition compliance and FM approved Intelligent Addressable

multi- criteria detector (optical and thermal sensors) complete with standard base,

facility to mount in different comprehensive environment, Tri-color detector-

status LED with 360 ° view, microprocessor circuitry with error

check; detector self-diagnostics and supervision programs,Rate-of-Rise

1 MR Detection: 15°F / min. (8.3°C / min.) - Fixed: 135°F (57°C) , Field Nos 40 ₹3,238.00 ₹1,29,520.00

programmable as rate-of-rise or fixed temperature, Polarity insensitive, Superior

EMI and RFI immunity, RoHS compliant. Detector shall have in-built isolator

for better reliability, circuit integrity and advanced fault finding.

Manufacturers not having in-built Isolator feature in detector shall consider

Isolator base in place of standard base OR separate Isolator before and

Supplying, installation, testing & commissioning of response indicator on

surface/recessed MS Box having two LED, metallic cover complete with all

SITC of UL Listed and FM approved Intelligent Addressable Rate of

Rise and Fixed temperature detector complete with standard base, Seven

(7) field-selectable settings in a temperature range of 135°F – 174°F

(57.2°C – 78.9°C) , a low-temperature warning of 40°F (4.4°C), facility to

mount in different comprehensive environment, Tri-color detector-status LED with

3 MR 360 ° view, microprocessor circuitry with error check; detector self- Nos 1 ₹2,660.00 ₹2,660.00

diagnostics and supervision programs, Field programmable as rate-of-rise

or fixed temperature, Polarity insensitive, Superior EMI and RFI immunity,

RoHS compliant. Detector shall have in-built isolator for better reliability,

circuit integrity and advanced fault finding. Manufacturers not having in-built

Isolator feature in detector shall consider Isolator base in place of standard

SITC of UL Listed Sounder cum Strobe rated at 75 dBA @ 3m for Audible

annunciation and 75cd flashintg at 1 Hz for visual indication.

SITC of UL listed and FM approved Intelligent addressable Class X type

(Style 7), Control Module with built in dual isolator, polarity insensitive, Tri

5 MR color LED for status (Green for Normal,Yellow for Faulty and RED for Nos 2 ₹5,204.00 ₹10,408.00

activation), Operating Temp and RH: 0-49 deg C and <=95%. Module shall

have in-built isolator for better reliability, circuit integrity and advanced fault

finding. Manufacturers not having in-built Isolator feature shall provide

Supplying, installation, testing & commissioning of addressable phone control

module complete as required.

SITC of UL listed and FM approved Intelligent addressable Class X type

(Style 7), Monitor Module with built in dual isolator, polarity insensitive, Tri

color LED for status (Green for Normal,Yellow for Faulty and RED for

7 MR activation), Operating Temp and RH: 0-49degC and <=95%. Module shall Nos 2 ₹3,932.00 ₹7,864.00

have in-built isolator for better reliability, circuit integrity and advanced fault

finding. Manufacturers not having in-built Isolator feature shall provide

separate Isolator before and after every Module to comply the same without any

extra cost. (For Flow Switch Monitoring/ Gass suppresion Integration etc.)

Digitally signed by AMIT

SITC of UL268 10th edition compliance and FM approved Intelligent

Addressable Duct detector with 10ft sampling pipe (optical and thermal

sensors) complete with standard base, facility to mount in different

comprehensive environment, Tri-color detector-status LED with 360 ° view,

microprocessor circuitry with error check; detector self-diagnostics and

8 MR supervision programs,Rate-of-Rise Detection: 15°F / min. (8.3°C / min.) - Fixed: Nos 2 ₹17,001.00 ₹34,002.00

135°F (57°C) , Field programmable as rate-of-rise or fixed temperature, Polarity

insensitive, Superior EMI and RFI immunity, RoHS compliant. Detector shall

have in-built isolator for better reliability, circuit integrity and advanced fault

finding. Manufacturers not having in-built Isolator feature in detector shall

SITC of Isolator base

UL listed andinFM

place of standard

approved base addressable

Intelligent OR separateClass

(Style 7), Manual Pull Station Single Action, Shock and Vibration Resistant,

with built in dual isolator, polarity insensitive, Tri color LED for status

9 MR (Green for Normal,Yellow for Faulty and RED for activation), T-45 Key Nos 2 ₹5,551.00 ₹11,102.00

Reset lockset for easy maintenance, Operating Temp and RH: 0-49degC and

<=95%. MCP shall have in-built isolator for better reliability, circuit integrity and

advanced fault finding. Manufacturers not having in-built Isolator feature

shall provide separate Isolator before and after every MCP to comply the same

Supplying, installation, testing & commissioning of One controller supports 12

10 MR zones, expandable up-to 492 zones with 24-zone routers, Control and routing of 4 Nos 1 ₹3,30,289.00 ₹3,30,289.00

simultaneous audio channels,EN 54-16 system certification

SITC of Call station with soft touch button 15 freely programmable

11 MR buttons,Customization via built-in display and keys, Provision for installing Nos 1 ₹1,55,270.00 ₹1,55,270.00

emergency button and key switch,EN 54-16 system certification etc all required

12 28.3.2 Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker Nos 14 ₹1,025.00 ₹14,350.00

complete as required

Supplying, installation, testing & commissioning of Power amplifier,

13 MR 240W,Multiple outputs - 70 V / 100 V and 8/4 ohm, Temperature controlled forced Nos 1 ₹83,670.00 ₹83,670.00

front to back ventilation, directly stackable, Mains, battery back-up, and pilot tone

supervision, Dual inputs with priority switching complete as required.

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated

14 28.5.2 with annealed copper conductor having XLPE insulation, steel wire armouring & Mtr 125 ₹192.00 ₹24,000.00

FRLS/HFFR outer

Supplying and drawing of cable Fire Retardant PVC insulated copper

15 MR conductor cable in the existing surface / recessed steel conduit of Mtr 75 ₹180.00 ₹13,500.00

following pairs, cores and size including connections and interconnections

etc. as required.

Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all

ancillaries and accessories like coupler etc. as required.

Supplying & Fixing of battery operated illiminated "EXIT" signage, with

2hrs power Battery backup complete as required.

Digitally signed by AMIT

SITC of Remote Paging Microphone should be fully digital connected via

CAT6 Cable with Controller. The Microphone should have capability to

make announcement in 96 Zones and have all call facility. The Microphone

shall have ability to control music and should be able to route the music in zones.

18 MR Microphone should have maximum zones capacity up to 120 Zones. The Nos 1 ₹1,39,939.00 ₹1,39,939.00

Microphone should have LED indication for the different faults, the unit

shall be able to indicate AC, DC, Fault, Mic and Test status through LED.. The

Unit shall have 2 RJ45 ports for Microphone so that the other microphone

shall be Installation,

Supply, able to linkTesting

andunit. The Microphone

Commisioning shall have

of repeater ability

160 character display with backlit control compatible with existing system

Supplying, installation, testing and commissioning of micro processor based

intelligent addressable main fire alarm panel, central processing unit with the

modules and capable of supporting not less than 240 devices (including

detectors) and minimum 120 detectors per loop and loop length up to 2 km,

21 28.2.1 network communication

card, minimum 320 character graphics/ LCD display with touch screen or other

keypad and minimum 4000 events history log in the non volatile memory

supply unit (230 ± 5 % V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance

free batteries with automatic charger The panel shall have facility to connect

printer to printout log and facility to have seamless integration with analog/digital

Digitally signed by AMIT

SCHEDULE OF QUANTITIES: FIRE PIPING, HYDRANTS, SPRINKLERS AND ACCESSORIES

S No DSR 2025/ DESCRIPTION QTY UNIT RATE TOTAL TOTAL AMOUNT

S No DSR 2025/ DESCRIPTION QTY UNIT RATE TOTAL TOTAL AMOUNT

DSR (INR) NON-DSR (INR)

Providing, laying, testing & commissioning of 'C' class

heavy duty MS pipe conforming to IS 3589/IS 1239

including Welding, fittings like elbows, tees, flanges,

27.7 tapers, nuts bolts, gaskets etc. and fixing the pipe on

1 the wall/ceiling with suitable clamp/support frame and

painting with two or more coats of synthetic enamel

paint of required shade complete as required :

Supplying, fixing, testing and commissioning of

butterfly valve of PN 1.6 rating with bronze/gunmetal

2 27.11 seat duly ISI marked complete with nuts, bolts,

washers, gaskets conforming to IS 13095 of

following sizes as required :

Providing, fixing, testing & commissioning of 15mm dia

27.21 quartzoid bulb type sprinklers of rating 68 degree

centigrade with required accessories :

27.21.4 Concealed type 15 Each ₹1,553.00 ₹23,295.00

Providing, installation, testing & commissioning of ₹264.00 ₹9,240.00

3a 27.29 adjustable rosette plate for 15mm dia in white finish 35 Each

UL Listed or FM approved complete as required.

Digitally signed by AMIT

Supplying, installation, testing & commissioning of

sprinkler flexible pipe (UL Listed) of stainless steel

complete with 15 NPT on reducer thread with maximum

working pressure of 175 PSI test pressure of 875 PSI

4 27.25 (Burst) with branch line (Inlet) 25mm NPT male thread

to sprinkler head (Outlet) 15mm NPT female thread with

reducer, nipple, 2 side brackets, center bracket,

stockbar of following sizes complete as required.

Providing and fixing ISI Marked of approved make Fire

5 Extinguishers complete with all accessories as per

manufacturer's specifications.

a) CO2 gas nozzle type - 4.5 Litre capacity (IS:15683). 2 NOS ₹12,070.00 ₹24,140.00

MR Mechanical Foam gas cartridge type. 9 Kg capacity

ABC dry powder stored pressure type 6 kg capacity

ABC dry powder stored pressure type 2 kg capacity

Providing and fixing portable hand held type ,

extinguishing system with CLEAN AGENT, with

proper supporting arrangements, complete with required

6 gas cartridge tested to a pressure of 30 kgf/cm2 all

MR necessary actuation devices.for UPS,

Hubroom,Electrical lab, Server room .(Make- Minimax/

Electrical Panel Suppresion

Digitally signed by AMIT

MR Supply of 2 Kg. Automatic Clean agent [LUKEFK5112]

tube based gas suppression system comprising

of: Cylinder of 2 kg capacity, factory filled with 2 kg.

LUKEFK5112 UL/FM Approved gas, with Direct Low

Pressure (DLP) valve assembly, push in connector for

tube, pressure gauge with mounting bracket, along with

necessary accessories and fittings to complete the

End of Line Adaptor along with Pressure

Gaguge,Pressure Switch, Flexible Polymer Detection

Tube with all necessary fittings & supports UL Listed 1 Each ₹42,000.00 ₹42,000.00

Tube & Health Monitoring cum Alarm panel With

Digitally signed by AMIT

S.NO Specification Qty Unit Rate In Rs Amount

1 Reception Table

Dimension(L)1800mm X (D)750mmX (H) 750mm (all over ht 1050mm) 1 no ₹95,444.00 ₹95,444.00

Supplying, and placing in position of reception Table. The table top made up of 36mm thick pre-laminated particle board and understructure shall be made of 25mm thick prelaminated particle

board with 2mm thk pvc edge banding . Modesty & side panel shall be 25mm thk prelam particle board with 2mm thk pvc edge banding . Table top height will be 750mm from the floor level &

one additional top at the height of 300 mm above the table top rest on SS stud . overall ht of the table 1050mm. The working edges shall be provided with machine pressed 2mm thick PVC

edging using special hot melt glue at hot temperature. Provision of Prelam particle board Mobile pedestal of size 400mm(L)x 450mm(D)x600mm(HT) (2 drawer + 1filling). Pedestal Top made

out of 18mm thick pre laminated particle board and rest all storage to be made out of 18 mm thick prelaminated particle board . All exposed edges shall be provided with machine pressed 2 mm

thick PVC lipping glued with hot melt EVA glue.

2 Side storage for Reception

Dimension: 1200mm(L) X 450mm(D) x 750mm(H) 1 no ₹21,500.00 ₹21,500.00

Supplying, and placing in position of medium height storage @ 750mm height. The storage unit having Openable shutters with shelf in it. The modular storage unit top shall be made from 18 mm

thick pre-laminated particle board and rest of the sides as well as shelves and shutter to be made up of 18 mm thick pre-laminated particle board while back to be made of 8 mm thick pre-

laminated particle board. All edges to be provided with 2 mm thick PVC lipping. The storage unit having openable shutters withD shape handles & locking arrangement.ge.

3 Reception Chair 1 nos ₹18,700.00 ₹18,700.00

Supplying and placing in position leatherette executive medium back chair size :- (w)720mm x (d)560mm x (h)1065mm. seat depth 500mm. seat width 560mm. back height 560mm. beautiful in its

simplicity, our collection welcomes you with its gentle curves and ergonomic comfort. tailored to perfection in sumptuous leatherette. all while adding refined sophistication to your modern

workspace. mechanism synchro single locking, function revolving, adjustable height, tilt tension control. ergonomic design helps maintain posture for better productivity. buttery soft leatherette

looks and feels opulent. padded seat, high backrest, and padded armrests offer a comfortable seating experience. pneumatic height adjustment lets you match the desk height. tilt tension control

lets you increase or decrease the resistance while you recline. synchronize recline up to 145 degree with single locking position offers a personalized comfort. 120 kg load-bearing capacity

ensures stability and security for the user. a sturdy metal base ensures longevity, all while elevating the aesthetic. high-quality castors ensure smooth noise-free movement.

Sofa for Reception area (3 seater)

3 Seater Dimension: (w)1830mm x (d)870mm x (h)710mm 1 nos ₹58,900.00 ₹58,900.00

Supplying and placing in position a upholstered lounge sofa,. the internal framework shall be constructed from 12 mm thick, anti-termite-treated plywood (tentatively grade 303 as per indian

standards for commercial, common, and moisture-proof plywood) with a controlled moisture content of less than 10–12% to ensure long-term structural stability and durability. the under-structure

frame shall further incorporate 12 mm thick kiln-dried german steam beech wood, selected for its superior strength and resistance to warping, thereby enhancing the overall durability of the sofa.

the seating base is to be fitted with a high-quality web suspension system that provides resilient support and ensures lasting seating comfort. all joints in the structure must be firmly bonded

using super bond adhesive and reinforced with star screws, wooden pins, and stapler pins to maintain long-term joint integrity under regular usage. the sofa design features a panelled back and

cushioned armrests to promote comfortable lounging, with the entire structure padded using high-resilience polyurethane (p.u.) foam of 32 density. the seat shall include 40 mm thick stack foam,

while the backrest and armrest cushioning shall also utilize 40 mm thick foam, all securely fixed using adhesive super glue. the final foam assembly will be upholstered in premium yellow 54-

pattern leatherette, selected for its premium feel, aesthetic appeal, and ease of maintenance. the sofa shall be complemented by stylish sleek mild steel (ms) legs .

Table for Reception area

Dimension:(W)1200mm X (D)600mm X (H)460mm 1 nos ₹27,500.00 ₹27,500.00

Supplying, and placing in position of center table. the ct collection is destined to become a centerpiece of your modern Indian homes. Perching on solid wood trestle legs, the veneer tabletop is

tastefully adorned with brick pattern, crafted to perfection by skilled Marquetry artisans.Tabletop crafted of premium engineered wood wrapped in Steam Beech veneer in Wenge finish.Veneer

features brick patterns, masterfully crafted by skilled Marquetry artisans.Legs are crafted of kiln-dried solid wood for added durability.Material & Subtype Veneer,Solid Wood - Steam Beech

Wood, Table Top Thickness 36mm,Colour & Colour Family Brown - Wenge.

Full Height storage for Entrance Lobby

Supplying, and placing in position of storage . The storage unit having shelf in it. The modular storage unit top shall be made from 18 mm thick pre-laminated particle board and rest of the sides

as well as shelves and shutter to be made up of 18 mm thick pre-laminated particle board while back to be made of 8 mm thick pre-laminated particle board. All edges to be provided with 2 mm

thick PVC lipping. The storage unit having combination of both with open shelves and openable shutter.

Conference Table

Digitally signed by AMIT

Supplying, and placing in position of conference table . The table top are made out of 36mm thk Prelam Particle board table top with 2mm thk pvc edge banding.Table top supported with 36mm

Side panel & 18mm thk Modesty panel with 2mm thk PVC edge banding.Providing metal wire raceway & junction connectivity of wires & cables also having a provision of 6 Module Flip top

8 Medium Back Chair for Conference 12 nos ₹17,500.00 ₹2,10,000.00

Supplying, and placing in position of high back chair . Medium Back Office Revolving Chair

With Cushioned Seat And Adjustable Armrest. Back:- Upholstered With Mesh Seat:- Plywood Hot Compressed Upholstered With Fabric.Armrest:- 2D Adjustable With Pu Pad, 1D Handle (

Grey ) With Pu Pad ( Black )

Mechanisam:-Synchro With Single Locking And Tension Adjustment.Base:- Nylon Base .

Full Height Storage for Conference

Supplying, and placing in position of full height storage @ 1800mm height as per photograph/drawing . The storage unit having Openable shutters with shelf in it. The modular storage unit top

shall be made from 18 mm thick pre-laminated particle board and rest of the sides as well as shelves and shutter to be made up of 18 mm thick pre-laminated particle board while back to be

made of 8 mm thick pre-laminated particle board. All edges to be provided with 2 mm thick PVC lipping. The storage unit having openable shutters with D shape handles & locking

120 Degree Workstation

Supplying and placing in position of 120-degree workstation size: (w)1050mm x (l)1050mm x (d)600mm x (h)750/1050mm. as per image. slanted shape metal legs of size 50mm x 50mm and

connectors of size 40mm x 40mm in metal powder coated 18mm thk softboard panel above table top at front side supported with metal powder coated holders. single metal wire raceway cover at

skirting level in partition. soft board and white board in partition above table top. soft board and white board in partition above table top. the complete partitioning work shall be carried out as per

the decision of engineer in charge. table top for workstation made up of 25mm thick pre laminated particle board of approved shade. the worktop shall be supported on 18mm thick pre laminated

particle board of approved shade. all working or non-working edges shall be provided with machine pressed 2mm thick pvc edging using special hot melt glue at hot temperature. provision of one

pvc keyboard tray and metal cpu trolley with lockable castors for each seating. also a provision of mobile pedestal unit size:- (l)400mm x (d)450mm x (h)600mm with a combination of 2 drawer &

one filing drawer. the pedestal storage unit shall be made of 18 mm thick prelaminated particle board with provision of handles & central locking arrangement.

Linear Workstation

Supplying, and placing in position of linear workstation .The worktop made out of 25mm thk. Prelam Particle board with 2 mm thk PVC edge banding.The Table top supported on Mild Steel of size

50mm x50mm Slanted Leg and 50mm x 25mm Horizontal connectors with Powder coating of 50 Micron.Middle Leg :- 0.8 mm thk Metal panel fixed on both side of the "T" leg for Vertical wire

carrying purpose.(Sharing Workstation). 0.8 mm thk Single/Double metal powder coated raceway with Powder coating of 50 Micron below top for wiring.Vertical wire carrying pole with powder

coating 50 micron below top for wiring( Non- sharing workstation ). Also having a provision of 0.8mm ms perfoated sheet hanging modesty. provision of 18mm thk fabric screen rest on the "D"

brackets on the table top between opposite seatings. All working or non working edges shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at hot

temperature. Also a provision of Pedestal Unit (size:- L-400mm x D-450mm x H-600mm) with a combination of 2 drawer & one filing drawer. The pedestal storage unit shall be made of 18 mm

thick prelaminated Particle board with provision of handles & Locking arrangement. Provision of pullout PVC keyboard tray and CPU trolley for each seating.Provision of glass divider between

Workstation Chair 27 nos ₹21,000.00 ₹5,67,000.00

Supplying and placing in position of medium back 360°-degree revolving chair all over size is: 630mm(l)x 675mm(d)x 1115mm(h) as per image, the chair made of full mesh in black colour.it will

comes in matte finish in contemporary style. Arms: armrest is having two adjustment heights (up & down) .Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat).seat: 40 ± 2

mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , back : frame of design shall be curved made of two pieces injection moulded frame cover

with mesh .backrest support adjustable lumbar support mechanism: self-weighted multi locking mechanism .only seat size is 520mm(l)x 525mm(d)x 445-545mm(h) & the back size is 470mm(l)x

590mm(h) ,seat maximum height is 545mm & minimum height is 445mm & back height from floor maximum height is 1115mm & minimum height is 1015mm .gas lift 100 mm telescopic

haudraulic base : 650 mm chrome base with smooth castors . .

Main Table for Director Cabin

Main Table Dimension: (w) 2000mm x (d) 1860mm x (h) 750mm. 1 nos ₹85,600.00 ₹85,600.00

supplying and placing in position of l-shaped director's desk size :- (w) 2000mm x (d) 1860mm x (h) 750mm. table top thickness 50mm. embodies the perfect harmony of curvaceous designs

and clean-lined forms, blending sophistication with everyday practicality. this tiered l-shaped director’s desk, featuring a striking contrast of dark oak and lacquered beige finishes, makes a bold

statement. thoughtfully designed with a concealed switchboard and versatile storage, it ensures a clutter-free workspace, allowing you to focus on what matters most. masterfully crafted of

premium engineered wood in dark oak and lacquered finish. a dark oak finish accentuates the unique grains & pattern of the wood. a solid lacquered finish adds a subtle contrast to the design.

spacious l-shaped tabletop offers ample workspace, ideal for multitasking and large projects. concealed switchboard keeps the workspace clutter-free. 1 password-protected drawer, 1 shelf and

2 cabinets keep your essentials protected and within reach. premium pu polish with low chemical emissions ensures healthy indoor air.

Main Chair for Director Cabin 1 nos ₹28,500.00 ₹28,500.00

Digitally signed by AMIT

Supplying and placing in position of 360 degrees revolving high back chair . The Leatherette office chair of size:- (W)655mm X (D)500mm X (H)1230mm is a ergonomic high back chair made for

a business tycoon or a director. The seat is constructed from a combination of resilient plywood and soft foam for a comfortable seat. The foam cushions are encased in a chocolate brown

leatherette upholstery. The seat arms come padded with foam and are covered in the same brown upholstery for a relaxed armrest. Powered by a synchro multi locking mechanism the chair

offers you extreme comfort as per your seating position. The office seat is supported by a shiny chrome base powered by sturdy nylon castors. Function: Revolving::Pneumatic Height Lift::Tilt

Tension Control::Synchro single locking, Base: Chrome Base, Locking Mechanism: Synchro single locking. The pneumatic height adjustment shall have adjustment stroke of 100mm and shall be

operated at 30kgs extension force. The Seat and back are made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of density 38-40 kg/m3

. The backrest has a foam of 28 (+/-2kg /m3 ) .

Visitor Chair for Director Cabin 2 nos ₹25,120.00 ₹50,240.00

Supplying and placing in position of 360 degrees revolving low back chair. The Leatherette office chair of size:- (W)555mm X (D)500mm X (H)1105mm is a ergonomic low back chair made for a

business tycoon or a director. The seat is constructed from a combination of resilient plywood and soft foam for a comfortable seat. The foam cushions are encased in a chocolate brown

leatherette upholstery. The seat arms come padded with foam and are covered in the same brown upholstery for a relaxed armrest. Powered by a synchro multi locking mechanism the chair

offers you extreme comfort as per your seating position. The office seat is supported by a shiny chrome base powered by sturdy nylon castors. The pneumatic height adjustment shall have

adjustment stroke of 100mm and shall be operated at 80kgs extension force. The Seat and back are made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam,

chair seat and back has foam of density 32-35kg/m3.

Back Storage for Director Cabin

Dimension: 2600mm(L) X 450mm(D) x 750mm(H) 1 nos ₹48,500.00 ₹48,500.00

Supplying, and placing in position of medium height storage @ 750mm height . The storage unit having Openable shutters with shelf in it. The modular storage unit top shall be made from 18

mm thick pre-laminated particle board and rest of the sides as well as shelves and shutter to be made up of 18 mm thick pre-laminated particle board while back to be made of 8 mm thick pre-

laminated particle board. All edges to be provided with 2 mm thick PVC lipping. The storage unit having openable shutters withD shape handles & locking arrangement.

Chair for Director Cabin

2 seater Dimension(W) 1530mm X (D)710mm X (H)770mm 1 nos ₹65,000.00 ₹65,000.00

Supplying and placing in position a upholstered 2-seater lounge sofa with overall dimensions of size (w)1530mm x (d)710mm x (h)770mm, providing an approximate seating area of 1400 mm

(w) × 570 mm (d). the internal framework shall be constructed from 12 mm thick, anti-termite-treated plywood (tentatively grade 303 as per indian standards for commercial, common, and

moisture-proof plywood) with a controlled moisture content of less than 10–12% to ensure long-term structural stability and durability. the under-structure frame shall further incorporate 12 mm

thick kiln-dried german steam beech wood, selected for its superior strength and resistance to warping, thereby enhancing the overall durability of the sofa. the seating base is to be fitted with a

high-quality web suspension system that provides resilient support and ensures lasting seating comfort. all joints in the structure must be firmly bonded using super bond adhesive and reinforced

with star screws, wooden pins, and stapler pins to maintain long-term joint integrity under regular usage. the sofa design features a panelled back and cushioned armrests to promote comfortable

lounging, with the entire structure padded using high-resilience polyurethane (p.u.) foam of 32 density. the seat shall include 40 mm thick stack foam, while the backrest and armrest cushioning

shall also utilize 40 mm thick foam, all securely fixed using adhesive super glue. the final foam assembly will be upholstered in premium burgundy-pattern leatherette, selected for its premium

feel, aesthetic appeal, and ease of maintenance. completing the design, the sofa will feature a sleek polished base frame paired with solid wood legs that have undergone a borate-based liquid

treatment or a protective wood finishing process. this premium multi-stage treatment ensures superior adhesion, exceptional durability, and maximum corrosion resistance, resulting in a high-

quality, elegant, and long-lasting product suitable for modern interiors.

Centre Table for Director Cabin

Dimension(W) 820mm X (D) 820mm X (H) 410mm 1 nos ₹26,500.00 ₹26,500.00

Supplying and placing in position of centre table. Featuring the graceful arc of a solid wood base and round marble-effect laminated top, this coffee table is all about balance. Base crafted from

kiln-dried solid wood in Walnut finish.Round tabletop features a premium laminate with a marble-inspired finish.The warm walnut finish contrasts beautifully with soothing, off-white hueGently

curved design adds visual rhythm.Material Subtype:Laminate, Solid Wood - Steam Beech Wood, Engineered Wood - Particle Board Base Material:Solid Wood, Colour & Colour Family:White -

Off, Brown - Walnut.

Low Height Storage for workstation area/ passage area

Supplying, and placing in position of low height storage @ 750mm height . The storage unit having Openable shutters with shelf in it. The modular storage unit top shall be made from 18 mm

thick pre-laminated particle board and rest of the sides as well as shelves and shutter to be made up of 18 mm thick pre-laminated particle board while back to be made of 8 mm thick pre-

laminated particle board. All edges to be provided with 2 mm thick PVC lipping. The storage unit having openable shutters with D shape handles & locking arrangement.

Dimension:2350mm(L) x 450mm(D) x 750mm(H) 1 nos ₹45,125.00 ₹45,125.00

Dimension:3900mm(L) x 450mm(D) x 750mm(H) 1 nos ₹75,000.00 ₹75,000.00

Dimension:2700mm(L) x 450mm(D) x 750mm(H) 1 nos ₹51,250.00 ₹51,250.00

Dimension:1680mm(L) x 450mm(D) x 750mm(H) 1 nos ₹29,000.00 ₹29,000.00

Main Table for Senior Scientist Cabin/ Accounts Head Cabin

Supplying, and placing in position of main Table. Modular tables of size 1500mm(L) x 750mm(D) x 750mm(H). The Table top are made out of 25mm thk prelam particle board with 2mm thk pvc

edge banding & side panel & modesty panel are made up of 18mm thick pre-laminated particle board .The working edges shall be provided with machine pressed 2mm thick PVC edging using

special hot melt glue at hot temperature. The table have a provision of Side Storage of size 750mm L x 450mm D x 750mm Ht., Storage Top are made out of 25mm thick pre laminated particle

board and rest all storage to be made out of 18 mm thick prelaminated particle board . All exposed edges shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt

EVA glue. Side Storage having a provision of 3 drawer unit of size: 400mm(L) x 450mm(D) x 675mm(H) attached to the side storage top with the help of shiny metal rods. Pedestal Unit have a

combination of 2 drawer & one filing drawer. The pedestal storage unit shall be made of 18 mm thick prelaminated Particle board with provision of central Locking arrangement.

Digitally signed by AMIT

Main Table Dimension : 1500mm(L) X 750mm(D) X 750mm(H)

Overall Side Unit Dimension : 1500mm(L) X 450mm(D) x 750mm(H)

Back Storage for Accounts Head Cabin

Supplying, and placing in position of low height storage @ 750mm height . The storage unit having Openable shutters with shelf in it. The modular storage unit top shall be made from 18 mm

thick pre-laminated particle board and rest of the sides as well as shelves and shutter to be made up of 18 mm thick pre-laminated particle board while back to be made of 8 mm thick pre-

laminated particle board. All edges to be provided with 2 mm thick PVC lipping. The storage unit having openable shutters with D shape handles & locking arrangement.

Dimension:1980mm(L) x 450mm(D) x 750mm(H) 1 nos ₹39,500.00 ₹39,500.00

Dimension:2750mm(L) x 450mm(D) x 750mm(H) 1 nos ₹51,000.00 ₹51,000.00

Back Storage for Senior Scientist Cabin

Supplying, and placing in position of full height storage @ 1800mm height. The storage unit having Openable shutters with shelf in it. The modular storage unit top shall be made from 18 mm

thick pre-laminated particle board and rest of the sides as well as shelves and shutter to be made up of 18 mm thick pre-laminated particle board while back to be made of 8 mm thick pre-

laminated particle board. All edges to be provided with 2 mm thick PVC lipping. The storage unit having openable shutters with D shape handles & locking arrangement.

Main Chair for Senior Scientist Cabin/ Accounts Head Cabin 5 nos ₹20,020.00 ₹1,00,100.00

Supplying & placing in position of high back 360°-degree revolving chair all over size is: 640mm(l)x 670mm(d)x 1350mm(h) the chair made of full mesh in black colour .it will come in matte finish

about style type is modern. Arms: armrest is having two adjustment heights (up & down). use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat). Seat: 40 ± 2 mm thick

polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat, back: frame of design shall be curved made of two pieces injection moulded frame cover with mesh.

backrest support adjustable lumbar support mechanism: self-weighted multi locking mechanism. Only seat size is 500mm(l)x 500mm(d)x 540-440mm(h) & the back size is 480mm(l)x 815mm(h),

seat maximum height is 540mm & minimum height is 440mm & back height from floor maximum height is 1350mm & minimum height is 1250mm. gas lift 100 mm telescopic haudraulic base: 650

mm chrome prong base is 620mm pitch centre dia (660mm with castors) .

Visitor Chair for Senior Scientist Cabin/ Accounts Head Cabin 10 nos ₹17,740.00 ₹1,77,400.00

Supplying & placing in position of medium back 360°-degree revolving chair all over size is: 640mm(l)x 670mm(d)x 1100mm(h), The chair made of full mesh in black colour.it will come in matte

finish about style type is modern. Arms : armrest is having two adjustment heights (up & down) .use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat).seat: 40 ± 2 mm thick

polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , back : frame of design shall be curved made of two pieces injection moulded frame cover with mesh

.backrest support adjustable lumbar support mechanism: self-weighted multi locking mechanism .only seat size is 500mm(l)x 500mm(d)x 540-440mm(h) & the back size is 480mm(l)x 570mm(h)

seat maximum height is 540mm & minimum height is 440mm & back height from floor maximum height is 1100mm & minimum height is 1000mm .gas lift 100 mm telescopic haudraulic base: 650

mm chrome prong base is 620mm pitch centre dia (660mm with castors) .

Sofa for Senior Scientist Cabin/ Accounts Head Cabin

Supplying, and placing in position of sofa .classic Contemporary design and slender curves. . The Sofa of stands Firm on solid PVC legs with thick armrests that are slightly curved on the front

face of the sofa. Each curve defines a seating space which provides for people to be seated comfortably. Finished in a Leatherette, the sofa makes a fantastic first impression. The Cushioning is

moulded such that it flows along the partition for a clean unified look. steam beech solid wood have used for framing construction of sofa The seat cushion is made of multi layered foam of

density 32-35kg/m3. The seating cushion have 2.75 & 1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch strength . The backrest has a foam of 28kg/m3

with polyester poly fill outer layer of 200 gsm. The polyester poly fill keeps the upholstery wrinkle free & soft.

3 seaterDimension(W)1905mm X (D)890mm X (H)870mm 3 nos ₹59,450.00 ₹1,78,350.00

2 seater Dimension:(W)1410mm X (D)890mm X (H)870mm 2 nos ₹52,320.00 ₹1,04,640.00

Side Table for Senior Scientist Cabin/ Accounts Head Cabin

Supplying and placing in position of Side table., the collection is destined to become a centerpiece of your modern Indian homes. Perching on solid wood trestle legs, the veneer tabletop is

tastefully adorned with a brick pattern, crafted to perfection by skilled Marquetry artisan Material & Subtype:Veneer/Solid Wood - Steam Beech Wood,Leg Material:Solid Wood, Finish:Matte

Colour & Colour FamilyBrown - Wenge. T

Dimension:(W)650mm X (D)500mm X (H)460mm. 3 nos ₹19,600.00 ₹58,800.00

Full height Storage for Passage area

Supplying, and placing in position of full height storage @ 1800mm height . The storage unit having Openable shutters with shelf in it. The modular storage unit top shall be made from 18 mm

thick pre-laminated particle board and rest of the sides as well as shelves and shutter to be made up of 18 mm thick pre-laminated particle board while back to be made of 8 mm thick pre-

laminated particle board. All edges to be provided with 2 mm thick PVC lipping. The storage unit having openable shutters with D shape handles & locking arrangement.

Net Total Amount Including GST@18% In Rs= ₹69,06,751.00

Net Total Amount Including GST@18% In Rs= ₹69,06,751.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES-SIGNAGE

S No DSR/ MR Description y Unit Rate DSR Amount NDSR Amount

Creating the signage logo at reception area with/

without light as per the directions of EIC

Providing and Fixing Logo & Signage in 3D ,as per the

approved Design/ pattern with Mat

/Gloss Finish Brass Letters with Mettalic/ Acrylic Base,

complete as required at site with the direction of the

2 MR Enginner In Charge 60 Sqft ₹1,572.00 ₹94,320.00

Digitally signed by AMIT

S DSR/M SCHEDULE OF QUANTITIES: LANDSCAPE DSR Non DSR

NO R Description Unit Qty Rate Amount Amount

Supply of full soil fill conical shaped planters of specified volume and dimensions

in stone finish or equivalent. planters to be indigenously made by rotational

moulding, with homogeneous recyclable, industrial grade polymer-resin mix, and

textured surface. planters should have an integrated water outlet hole & plug,

single layered peel-proof construction, light weight, rust proof, uv stabilized, anti-

frost feature without any joints, and easy to clean. planter supplier must give 1

year warranty against any fading or cracking for both indoor and outdoor use.

green plant and laying is extra. potting instructions as per company catalogue.

Plantation: Supply and installation of Natural Plant with sand, fertilizer etc.

Providing & fixing Artificial silk plants with combination 3 or 4 types uniformly

distributed plants as ceiling suspended creepers with necessary wire or hanging

arrangement included. Plants which ultraviolet blocking chemicals are

impregnated into the materials during the manufacturing process. These

chemicals are blended with the plastic or PVC parts Installation . Suspended

creepers shall be installed in laminated finish trays duly suspended from the

ceiling with twisted rods of size and design as per the detailed drawings complete.

Digitally signed by AMIT

SCHEDULE OF QUANTITIES: SCULPTURE/ART WORK

S.NO Specification Qty Unit Rate In Rs Amount Ref Image

A) 6 Feet Tall Brass Lord Vishnu Idol/ OR any other Brass Sculpture

as per directions of EIC

1. Description: Custom handcrafted pure brass sculpture of Lord Vishnu

Height: 6 feet (approx 180 cm)

Full detail carving (Vishnu with traditional attributes/shankha-chakra, etc.)

Finish: Polished golden brass

Base: Brass/Marble stand

2. Material & Make:

✔ Pure brass casting (lost-wax/traditional casting)

✔ Hand-finished by artisan

1 ✔ Clear lacquer/anti-tarnish coating 1 no ₹3,20,000.00 ₹3,20,000.00

C) ART WORKS : Providing, supplying & installing premium hand-painted

artwork for office interiors, comprising one 4′×6′ painting for office area

and one 8′×6′ painting for Director’s office, executed on high-quality artist

canvas using acrylic/oil/mixed media, finished with UV-protective coating,

complete with approved framing, all fixing accessories, transportation and

installation, complete in all respects. (Image is for reference only. Engineer

3 in charge shall finalize the art work) 10 nos ₹25,000.00 ₹2,50,000.00

Net Total Amount Including GST@18% In Rs= ₹5,70,000.00

Net Total Amount Including GST@18% In Rs= ₹5,70,000.00

Digitally signed by AMIT

S.No. Description Unit Qty.

A Active Purification System (Bi-Polar Ionization)

Supply, Installation, Testing and commissioning of

Bipolar Ionisation System. The Bipolar Ionization System

must be a combination of Needle Point Model for AHU

(Needle Point should have Nitinol (nickel titanium)

Needles and Carbon Fiber Brush Model for Cassettes

and HI Wall AC units. The System should produce

positive and negative ions for creating a Bio Climate rich

in ions and hence neutralizing harmful pollutants

including pathogens, Volatile Organic Compounds and

Particulate Matter.

The Carbon Brush self-balancing ionizer should be

installed at the fan inlet of fan coil units, VRF cassettes,

ductless splits , NeedlePoint Ionizer shall be installed at

AHU and Ductable HVAC System.

Split/casatte/AHU 9 15500 139500

B Electronic Air Cleaner For AHU/DUCTABLE

The EAC Shall be suitable to reduce harmful pollutants

like particulate matter (PMx), PM 2.5, allergens, smoke,

bacteria, pathogens etc. based on below principle

technology viz; Impingement, Polarization and

Agglomeration for passive air purification. It should be a

slim structured unit specifically designed for integration

in Return Air path of ceiling suspended indoor units and

AHUs. Data shall be compatible with BMS/IoT platforms

(Modbus/Wi-Fi). The system shall support analytics such

as filter health indication and early maintenance alerts,

with an option for integration into AI-based dashboards

for trend analysis and compliance reporting.

3 Indoor Air Quality Monitoring System-

Digitally signed by AMIT

Supply, Installation, Testing & commissioning of IAQ

Monitor to remotely measure the levels of PM 2.5, VOCs,

CO2, Temperature, Humidity on a real time basis. The

IAQ Monitor shall be capable of getting connected with

Wi-Fi. The Monitor should be capable of sending the

indoor air quality information on display Screen / Nos. 1 44000 44000

Mobile/Workstation as per Client's requirement. Quoted

price shall be inclusive of all necessary arrangement as

required to make the unit proper functional. The System

should provide Soft Assistance in form of Notifications

and Alerts for Periodic Preventive Maintenance.

TOTAL ITEM 370500

NET Total 3,70,500.00

Digitally signed by AMIT