SPL REPAIR TO BLDG NO. 101 (WKSP FLOOR AREA/ROOF SHEET) OF 181 FD WKSP COY EME IN ZONE -10 AT TALBEHAT MIL STN

Amount

Dismantling asbestos cement (corrugated, semi corrugated etc) sheets in roof coverings including ridges complete.

Dismantling timber scantlings 40 Sqcm and over in section, in unframed work in any position complete.

S&F for Rolled mild steel sections conforming to Gde Fe-290(Gde-165-E) as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails & guides for sliding doors, fixed with angle cleats or other connecting plates complete all as specified.

M&l multi-rib TM profile high tensile 550 MPA yield strength colour coated galvalume corrugated steel sheet having maximum pitch of 250mm, c/c and minimum 30mm crest depth in length as per site requirement. The feed material is to be manufacture out of 0.80mm (TCT). Total coated thickness with 18-20 microns top coat over 5 microns primer and 8-10mm alkyd backer, zinc aluminium alloy of AZ-150. The sheet shall have a hot dip metallic zinc aluminium alloy coating of zinc 43.5%, aluminium (55%)and silicon (1.5%) with ttoal mass coating of 150 gms/sqm on both sides. Covered width will be 1020mm and sheet length as per site requirement. The profile is having return leg for proper side lap. The sheet shall be fixed using self drilling/self capping screws with EDPM seal or fixed with 'L' or 'J' type or cranked hook bolts in roof,complete all as specified and directed by Engr-in-charge.

M&L for preparation of new untreated steel surface of any description exc 10cm width or girth applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&l multi-rib TM profile high tensile 550 MPA yield strength colour coated galvalume plain steel sheet having maximum pitch of 250mm, c/c and minimum 30mm crest depth in length as per site requirement. The feed material is to be manufacture out of 0.80mm (TCT). Total coated thickness with 18-20 microns top coat over 5 microns primer and 8-10mm alkyd backer, zinc aluminium alloy of AZ-150. The sheet shall have a hot dip metallic zinc aluminium alloy coating of zinc 43.5%, aluminium (55%)and silicon (1.5%) with ttoal mass coating of 150 gms/sqm on both sides. Covered width will be 1020mm and sheet length as per site requirement. The profile is having return leg for proper side lap. The sheet shall be fixed using self drilling/self capping screws with EDPM seal or fixed with 'L' or 'J' type or cranked hook bolts in roof,complete all as specified and directed by Engr-in-charge.

M&L for 600 mm stailess steel 304 grade wind driven roof turbo ventilator with 42 N0s of vanes , thichneess of vanes 0.5 mm each , 02 nos twin sealed permanantly lubricated bearing , the turbo ventilator with matching UV stabilized FRP base plateis suited for Building complete all as specified and directed by Engineer-in-Charge.

Surface preparation and removing the debris and cleaning the concrete surface bygrading up to 1mm existing surface. Treating the construction joints: chase opening the joints by providing “V” groove, removing the dust and clean filling.

Providing, laying and carrying out joint less 2mm thick epoxy screed & 1mm thick epoxy topping approved flooring over the hard wearing, surface with materials of approved manufacturer surface preparation, one coat epoxy based primer coat (coverage 150gms per SM), followed by base coat epoxy screed of 2mm thick three component system(cov: 3kg/SM) and final top 1mm thick epoxy flooring with three component system/ self-smooth glossy finish(cov: 1.5 kg/SM) all as per manufacturer’s specifications inclusive of necessary curing, finishing, and carrying complete all as specified and directed by Engr-in-charge.

Supplying & fixing Solar Control Polycarbonate sheet (Multiwall) of approved make & brand conforming to IS: 14443-1997 and having 50 micron UV protection layer under co-extrusion technology,Fire rating being B-s1 as per EN13501-1 certification, fitted and fixed with 60mm wide aluminium channel section top and bottom member in dry-glaze sandwitch system, (unit wt. of top and bottom members: 0.375 kg/m & 0.69 kg/m) of approved brand and profile, EPDM quality rubber gaskets, anti dust tape, end closer "C" channel and 75 mm long Self tapping screw being drilled through the centre leg of the bottom section with nuts placed at 300 mm apart without anyway puncturing the polycarbonate sheet, EPDM Washer 16 mm dia & 3 mm thick washer etc complete strictly as per manufacturers specification and direction of Engineer-in- Charge. (Payment to be made on area of finished work) . In Roof:- Natural/ blue/Green/Bronze/Opal/Metallic grey colour With 2 wall 10 mm overall thickness (wt.1.70kg/sqm,Ugvalue being 3.1 W/m2K, Min. cold bending radius of 1200 mm) Sqm. 140.70 1544.00 217240.80 3 (a) Priming one coat on steel or other

Note :- Debris obtained from all items should be removed in low lying areas as directed by Engr-in-charge out of MOD Land. (Rates quoted for items are deemed to be included for this, where removal of debris in the items is not considered.)

M/S Kharya Associates (BID ID -3118128)

M/s Dinesh Kumar (BID ID -3119332)

M/S SHIVA TRADERS (BID ID -3118553)

M/s Ravi Traders (BID ID -3119449)

M/S Ritu Tandon (BID ID -3119084)

M/S SACHENDRA KUMAR JAIN (BID ID -3118395)

m/s bobby enterprises (BID ID -3118478)