Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L-1₹25.3 LAccepted-AOC | L-1 | Accepted-AOC L-1 | |
| 2 | L-2₹28.5 L+₹2.1 L (8.00%)Rejected-Finance | L-2 | Rejected-Finance NOT BEING A LOWEST BIDDER | |
| 3 | L-3₹29.6 L+₹3.2 L (12.1%)Rejected-Finance | L-3 | Rejected-Finance NOT BEING A LOWEST BIDDER | |
| 4 | L-4₹29.8 L+₹3.3 L (12.7%)Rejected-Finance C O S 1 ESS GEE COMPLEX NEAR J K BANK SONAWAR BAZAR B B CANTT SRINAGAR 190004 J K | SRINAGAR | SRINAGAR | JAMMU AND KASHMIR | 190004 | L-4 | Rejected-Finance NOT BEING A LOWEST BIDDER | |
| 5 | L-5₹29.8 L+₹3.4 L (12.8%)Rejected-Finance | L-5 | Rejected-Finance NOT BEING A LOWEST BIDDER |
Tender Value
₹35 L
EMD Value
₹70,000
Closing Date
11 Aug 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE 861 EWS
GE 861 EWS C/O 56 APO
REPAIR TO CERTAIN TEMPORARY AND PERMANENT BUILDINGS AT UPPER AND LOWER CAMP OF KHUNDRU UNDER GE 861 EWS
2022_MES_537598_1
GE 861 EWS-31/2022-2023
Open Tender
Civil Works
Item Rate
270 days
GE 861 EWS
AS PER NIT
7 documents required · 7 mandatory
₹500
GE 861 EWS
₹70,000
Yes
22 Sept 2022
13 Jul 2022
18 Aug 2022
13 Jul 2022
11 Aug 2022
28 Jul 2022
60 days
Amount
Taking down cement plaster on brick or concrete surfaces including raking out joints, hacking for key scrubbing down with water etc complete all as specified and directed.
Demolition of brick work or stone boulder masonry built in cement mortar including all arches quoins etc but excluding ashlar facing, dressed stone work & precast concrete articles etc complete all as specificed and directed.
Demolition of cement concrete (unreinforced) in ground floors & paving n.exc 15 cm thick (below or above ground level) complete all as specified and directed.
Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store complete all as specified and directed.
Dismantling boarding of any description, fixed in any position with nails, complete all as specified and directed.
Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n.exc 1.5 sqm complete all as specified and directed.
Taking down chowkat or frame with shutters (without taking shutter from the frame) exceeding 1.5sqm and not exceeding 4.00 sqm each complete all as specified and directed.
Taking down shutter of any description area n.exc 1.00 sqm each complete all as specified and directed.
Taking down of shutter any description area exceeding 1 sqm but not exceeding 2 sqm each complete all as specified and directed.
Dismantling timber scantling unframed 40 sq cm and over in section in any position, complete all as specified and directed.
Taking up or down 15mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specified and directed.
Taking up or down 20mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specified and directed.
Demolition wall and ceiling boards (fibre, Pulp, insulation etc) or insulation board/slabs/blankets, any thickness, including cover fillets & snap grid frame etc, complete all as specified and directed.
Dismantling plain or corrugated steel sheeting , any gauge and thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed.
Dismantling structural steel work including doors, gates but excluding framed truss etc., complete all as specified and directed.
Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc, laid, bedded and pointed in any mortar, complete all as spcified and directed..
Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed.
Brick work with sub class 'B' bricks straight or curved on plan, exceeding 6m mean radius with old size bricks, built in cement mortar 1:6, complete all as specified and as directed.
All as per the description of item No. 18 here-in- before but except bricks.
Brick work with sub class 'B' bricks, straight or curved on plan, to any radius, in half brick thick wall, using old size brick, built in cement mortar 1:4, complete all as specified and directed.
Walling of random rubble masonry with best quality stone, uncoursed, well bonded, bedded and solidly hearted and built in CM 1:6, all as specified.
All as per the description of item No. 21 here-in- before but except bricks.
15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4 finished the surface even and smooth without using extra cement, complete all as specified and directed.
10mm thick rendering on fair faces of brick or concrete surfaces in CM 1:6 finished even and smooth without using extra cement, complete all as specified and directed.
10mm thick rendering on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing in CM 1:6 finished even and smooth without using extra cement, complete all as specified and directed.
5mm thick rendering on fair faces of brick or concrete surfaces in CM 1:3 finished even and smooth without using extra cement, complete all as specified and directed.
Non-skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6, complete all as spcified and directed.
Glazed ceramic coloured tiles 450mm x 300mm x 6mm thick as in vertical surfaces such as skirting dado etc set and jointed in neat cement slurry, pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 to receive tiles, complete all as specified and directed.
Vitrified tiles 10 mm thick, light shade (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15 mm thick screed bed in cement mortar 1:6, complete all as specified and directed.
Chequered coloured cement concrete tiles of size 300 x 300 x 18-20mm thick, with grey cement and pigment, set, jointed and pointed in neat cement slurry, laid in floors, over and including 15 mm thick screed bed in cement mortar 1:6, complete all as specified and directed.
Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.
Machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed and including 10mm thick rendering in cement mortar 1:4 to receive, complete all as specified and directed.
20mm thick granite (of any type) tiles machine cut, in skirting/dado laid over 15mm cement screed in cement mortar 1:6 and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete, complete all as specified and directed.
18-20mm thick udaipur green marble stone (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed.
60mm thick factory made machine pressed precast concrete coloured interlocking paver block with grey cement and pigment, any shape, size and design as approved by Engr-in charge confirming to IS 15658-2006, M-35 grade, complete all as specified and directed.
Sand filling under floors or in foundation including watering and consolidation, complete all as specified and directed.
40mm thick PCC 1:2:4, type B-1 (using 20mm graded crused stone aggregate) as in floors, finished even and smooth without using extra cement, complete all as specified.
50mm thick PCC 1:4:8 type D-2 (40mm graded stone aggregate) as in sub-floor, sub-base, floor and pavings, etc., complete all as specified and directed.
Plain cement concrete M-10, 1:3:6, type C-2, using 40mm graded mechanically crushed stone aggregate, 50mm thick, as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified and directed. Note:- The unit rate include for use of form work (straight or curved).
Rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe-290 Gde E-165, complete all as specified and directed.
Anodised aluminium powder coated frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.
Anodised aluminium powder coated door shutters, single panel with floor door spring with powder coated aluminium frame of section 100x44x 2mm and shutter having stile, top rail, lock rail and botton rail of section 44.50x83.50x1.80mm including 5.5mm thick tinted sheet glass ordinary quality including necessary joining cleats, glazing clips, ruber neoprene packing, suitable push and pull plate/handle, 1 No 200mm long aluminium tower bolt, 1 No mortice brass lock 100mm size 4 lever (vertical type), handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc., complete all as specified and as directed.
Factory made solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing shown in SSR Part-II, complete all as specified and directed.
Factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rails and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to in stiles & rails with suitable PVC sheet beading and joinned together with solvent cement supplying & fixing in frames at site as per specification and drawing shown in SSR Part -II, complete all as specified and directed.
35mm thick, 2nd class softwood factory made, plain framed, panelled shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneers on both faces. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated, fitted to chowkats, complete all as specified and directed.
35mm thick, 2nd class softwood factory made glazed and skeleton shutters, open rebated and prepared to receive glass or gauge,etc. (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing gauge sizes of members of shutters as specified in SSR Part-I Section-8, clause 8.24 (a) for door shutter supplying and fitted to chowkats, complete all as specified and directed.
30mm thick, 2nd class softwood factory made glazed and skeleton shutters, open rebated and prepared to receive glass or gauge,etc. (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing gauge sizes of members of shutters as specified in SSR Part-I Section-8, clause 8.24 (b) for door shutter supplying and fitted to chowkats, complete all as specified and directed.
2nd class softwood, plain, solid, straight chowkats and frames, wrought, framed, worught, framed rebated on the solid, rounded of chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.
6mm thick plywood, grade BWR, type BB, fixed in walls with nails to timber frame, complete all as specified and directed.
6mm thick plywood, grade BWR, type BB, fixed in ceiling flat and sloping with nails to timber frame, complete all as specified and directed.
4mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed in ceiling flat and sloping with nails to timber frame, complete all as specified and directed.
4mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed in walls with nails to timber frame, complete all as specified and directed.
2nd class softwood weather boarding, clean sawn, plain, 20mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps complete all as specified and directed.
2nd class softwood, as in scantling and similar work, clean sawn, timber fixed in position, complete all as specified and directed.
All as per the description of item No. 54 here-in- before but except timber.
2nd class softwood plain fillets square/rectangular or triangular in section of sectional area exc 13 Sqcm but n exc 25 Sqcm, complete all as specified and directed.
2nd class softwood plain fillets bull nosed splayed chamfered or rounded on one edge or face in section of sectional area exc 3 Sqcm but n exc 6 Sqcm complete all as specified and directed.
0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap with zinc coating of 275, fixed with 'L' or 'J' type or cranked hook bolts in roofs, walls etc. complete all as specified and directed.
All as per srl item No-58 here in above but except sheets, complete all as per specified and directed.
0.80mm thick plain galvanized mild steel sheeting in ridges, hips valley gutters, drip and straight flashings (length and girth as fixed)with grade of zinc coating 275 complete all as specified and directed.
Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mps as in roof covering /cladding to wall, fixed with self tapping screws as specified and directed.
Pre-painted galvalume aluminium zinc coating GI based plaind steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mps as in roof covering /cladding to wall, fixed with self tapping screws as specified and directed.
250mm size mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed.
150mm long mild steel barrel tower bolts, stove enamelled black, with bright bolts fixed, complete all as specified and directed.
100mm long mild steel barrel tower bolts, stove enamelled black, with bright bolts fixed, complete all as specified and directed.
150mm long, mild steel pressed handles, oval type, stove enamelled black, complete all as specified and directed.
125mm long, mild steel pressed handles, oval type, stove enamelled black, complete all as specified and directed.
100mm long, mild steel pressed handles, oval type, stove enamelled black, complete all as specified and directed.
100mm long, mild steel cold rolled butt hinges, medium weight, complete all as specified and directed.
75mm long, mild steel cold rolled butt hinges, medium weight, complete all as specified and directed.
S & F in repair aluminium (extruded section) body door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed, complete all as specified & directed
S & F in repair 300mm long mild steel ordinary rat tail rod pattern, springs including roller and roller plate fixed to wooden chowkhat, complete all as specified and directed.
4mm thick sheet glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.50 Sqm in each pane, complete all as specified and directed.
4mm thick figured glass pin headed type and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.5 Sqm in each pane complete all as specified and directed.
5.50mm thick sheet glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.50 Sqm in each pane, complete all as specified and directed.
Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm & fixed with stainless steel wire staples, complete all as specified and directed.
Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm & fixed with stainless steel wire staples (fixed in repair), complete all as specified and directed.
Steel water tubing, 15mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed.
All as per the description of item No. 78 here-in- before but except tubing.
Steel water tubing, 20mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed.
All as per the description of item No. 80 here-in- before but except tubing.
Rotational moulded polythylene 500 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20mm brass ball valve high pressure with brass rod & high density plastic ball including dismantlling of existing tank, complete all as specified and directed.
Rotational moulded polythylene 1000 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20mm brass ball valve high pressure with brass rod & high density plastic ball including dismantlling of existing tank, complete all as specified and directed.
S&F in repairs vitreous china squatting pan water closet, orissa pattern, size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) but including cast iron 'P' trap, jointing to flush pipe complete and making good to floor in cement concrete M-5 (1:5;10), type E-2 using 40mm graded crushed stone aggregate, complete all as specified and directed.
S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white, including 'P' or 'S' trap, seat cover and fixing bolts, flushing cistern and flush pipe & making good to floor in cement mortar M-15 (1:2:4) type B-1 (using 20mm graded crushed stone aggregated), complete all as specified and as directed.
S & F in repair for 125mm size brass chromium plated shower rose with or without swivel joints, any size including fixing to steel pipe of 15mm dia or union, complete all as specified.
S&F in repair 10 litre capacity PVC valveless, low level, synphonic action type, flushing cistern, with inlet, ball valve, float valve, handle including brackets, complete all as specified and directed.
S&F in repair vitreous china, wash hand basin, flat back of size 550mmx400mm with brackets including cutting for and pinning in ends of brackets, including 32mm dia PVC waste fitting, brass, chromium plated with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, complete all as specified and directed.
S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm, complete all as specified and directed.
S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.
S & F in repair 32 mm dia waste coupling of PTMT (half or full threaded) (minimum weigh 45 gms) complete all as specified.
S&F in repair 20 mm Ball valve high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed any colour high pressure screwed for iron pipe and fixed. (Minimum weight 210gms) complete all as specified and directed.
S&F in repair 20mm bore gun metal globe or gate valve with iron wheel head screwed head both for iron pipe & fixed, complete all as specified and directed.
S&F in repair 15mm bore gun metal globe or gate valve with iron wheel head screwed head both for iron pipe & fixed, complete all as specified and directed.
S & F in repair 15mm dia pillar taps, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered 'Hot' and 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.
S&F in repair 15 mm bore brass CP mixer for mixing hot and cold water screwed down for iron pipe and fixeds, complete all as specified and directed.
S & F in repair 15mm bore bib tap, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule, complete all as specified and directed.
S&F in repairs 15mm bore stop valves, fancy type, chromium plated with long long shank and cup (concealed type), cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union, complete all as specified and directed.
S & F in repair 110mm bore dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints fixed to walls, complete all as specified and directed.
S & F in repair 75mm bore dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints fixed to walls, complete all as specified and directed.
110mm bore dia PVC (SWR) bends, complete all as specified and directed.
75mm bore dia PVC (SWR) bends, complete all as specified and directed.
S&F in repairs 75mm dia outlet PVC (SWR) multi floor trap with grating including jointing with solvent cement, complete all as specified and directed.
S&F in repairs kitchen plate rack stainless steel 1mm thick of size 31"x36"x10" complete all as specified and directed
Plain cement concrete 1:3:6 mix type C1 (using 20 mm graded stone aggregate) cast in situ in lintels up to 1.5 M span, cills and other similar bands, plinth courses, parapets, copings, bed plates, hold fast and the like including weathering, slightly rounded or chamfered angles and throating as directed including use and waste of form work complete all as specified and directed.
Preparation of new plastered or unplastered surfaces of wall and applying two coats of cement base paint over a coat of alkali-resistant priming coat, complete all as specified and directed.
Preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer, complete all as specified and directed.
Preparation of new wooden surfaces of any description not otherwise described, exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.
Preparation of old painted wooden surfaces over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.
Preparation of new CGI/PGI steel surfaces of any description not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer over a coating of mordant solution including washing the surfaces, complete all as specified and directed.
Preparation of old painted steel surface of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified.
Preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white wash,complete all as specified and directed.
M/S Hilal Builders
M/s Hilal Constructions
M/S A.N CONSTRUCTIONs
M/S HAMID & CO
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .