GE 861 EWS-19/2023-24

Amount

Taking down chowkat or frame with shutters (without taking shutter from the frame) exceeding 1.5sqm and not exceeding 4.00 sqm each complete all as specified and directed.

Taking down Chowkhats or frames n. exc 1.5 Sqm each with shutters (without taking off shutters from the frames), complete all as specified and directed.

Taking down cement plaster on brick or concrete surfaces including raking out joints, hacking for key scrubbing down with water etc complete all as specified and directed. NOTE: The work is to be carried out upto 10 mtr height.

Demolition of brick work or stone boulder masonry built in cement mortar including all arches quoins etc but excluding ashlar facing, dressed stone work & precast concrete articles etc complete all as specificed and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc, laid, bedded and pointed in any mortar, complete all as spcified and directed.

Demolition of cement concrete (unreinforced) in ground floors & paving n.exc 15 cm thick (below or above ground level) complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store complete all as specified and directed.

Dismantling boarding of any description, fixed in any position with nails, complete all as specified and directed.

Demolition wall and ceiling boards (fibre, Pulp, insulation etc) or insulation board/slabs/blankets, any thickness, including cover fillets & snap grid frame etc, complete all as specified and directed.

Dismantling plain or corrugated steel sheeting , any gauge and thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc, complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as spcified and directed.

Dismantling timber scantling unframed 40 sq cm and over in section in any position, complete all as specified and directed.

Dismantling of unframed timber scantlings under 40 Sqcm in section in any position complete all as specified and directed

Taking up or down 15mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specified and directed.

Brick work with sub class 'B' bricks straight or curved on plan, exceeding 6m mean radius with old size bricks, built in cement mortar 1:6, complete all as specified and as directed.

All as per the description of item No. 17 here-in- before but except bricks.

15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4 finished the surface even and smooth without using extra cement including mixing of water proofing compound in the proportion as mentioned in manufacture's instructions complete all as specified. Note: (a) Water proofing compound shall be measured and paid for separately. (b) The work is to be carried out upto 10 mtr height.

10mm thick rendering on fair faces of brick or concrete surfaces in CM 1:6 finished even and smooth without using extra cement, complete all as specified and directed.

M&L rendering 10 mm thick on other than fair faces of brick work/stone work or concrete surfaces in cm 1:6 finished even and smooth (with out using extra cement) etc complete all as spd & directed

Supply only integral water proofing compound of approved quality, complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc.

Brushing neat cement slurry with 3.0kg of cement per sq. metre as in roof surface complete all as specified and directed.

15 mm thick Screed bed in CM 1:4 for roof surface, finished the surface even and smooth without using extra cement including mixing of water proofing compound in the proportion as mentioned in manufacture's instructions complete all as specified. Note: (a) Water proofing compound shall be measured and paid for separately. (b) The work is to be carried out upto 10 mtr height.

Non-skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile n.exc. 0.11 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6, complete all as spcified and directed.

Non-skid jointless coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6, complete all as spcified and directed.

Non-skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but not exc 0.18 sqm, as in skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering in CM 1:4 to receive tiles complete all as spcified and directed.

Glazed ceramic coloured tiles 450mm x 300mm x 6mm thick as in vertical surfaces such as skirting dado etc set and jointed in neat cement slurry, pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 to receive tiles, complete all as specified and directed.

Vitrified tiles 10 mm thick, light shade (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15 mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed and including 10mm thick rendering in cement mortar 1:4 to receive, complete all as specified and directed.

Chequered coloured cement concrete tiles of size 300 x 300 x 18-20mm thick, with grey cement and pigment, set, jointed and pointed in neat cement slurry, laid in floors, over and including 15 mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

60mm thick factory made machine pressed precast concrete coloured interlocking paver block with grey cement and pigment, any shape, size and design as approved by Engr-in charge confirming to IS 15658-2006, M-35 grade, complete all as specified and directed.

80mm thick factory made machine pressed precast concrete coloured interlocking paver block with grey cement and pigment, any shape, size and design as approved by Engr-in charge confirming to IS 15658-2006, M-40 grade, complete all as specified and directed.

Sand filling under floors or in foundation including watering and consolidation, complete all as specified and directed.

75mm thick PCC 1:2:4, type B-2 (using 40mm graded crused stone aggregate) as in floors, finished even and smooth without using extra cement, complete all as specified.

50mm thick PCC 1:4:8 type D-2 (40 mm graded stone aggregate) as in sub-floor, sub-base, floor and pavings, etc., complete all as specified and directed.

Plain cement concrete 1:3:6, type C-2, using 40mm graded mechanically crushed stone aggregate, 50mm thick, as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified and directed. Note:- The unit rate include for use of form work (straight or curved).

PCC 1:2:4, type B-1 using 20mm graded stone agregete as in sides of rounded or chamfered on edges of interlocking tiles including necessary formwork, complete all as specified and directed.

Cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork, complete all as specified and directed.

Rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe-410W (Gde E-250) quality-A, complete all as specified and directed.

All as per the description of item No. 42 here-in- before but fixing only.

6mm thick plywood, grade BWR, type BB, fixed in ceiling flat and sloping with nails to timber frame, complete all as specified and directed.

6mm thick plywood, grade BWR, type BB, fixed in walls with nails to timber frame, complete all as specified and directed.

4mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed in ceiling flat and sloping with nails to timber frame, complete all as specified and directed.

4mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed in walls with nails to timber frame, complete all as specified and directed.

2nd class soft wood weather boarding, clean sawn, plain, 20mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps complete all as specified and directed.

Supply & Fixing 20 mm thick 2nd class soft wood boarding fixed with nails in any situation and planed one side as in eave board, complete all as specified and as directed.

2nd class softwood, as in scantling and similar work, clean sawn, timber fixed in position, complete all as specified and directed.

All as per the description of item No. 50 here-in- before but except timber.

2nd class softwood plain fillets square/rectangular or triangular in section of sectional area exc 13 Sqcm but n exc 25 Sqcm including dismantling old unsv fillets, complete all as specified and directed.

2nd class softwood plain fillets square/rectangular or triangular in section of sectional area exc 3 Sqcm but n exc 6 Sqcm, complete all as specified and directed.

2nd class softwood plain fillets bull nosed splayed chamfered or rounded on one edge or face in section of sectional area n.exc 3 Sqcm complete all as specified and directed.

0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap with zinc coating of 275, fixed with 'L' or 'J' type or cranked hook bolts in roofs, walls etc. upto a height of 10-12m, complete all as specified and directed.

All as per the description of item No. 55 here-in- before but except sheets.

0.80mm thick plain galvanized mild steel sheeting in ridges, hips valley gutters, drip and straight flashings (length and girth as fixed)with grade of zinc coating 275 upto a height of 10-12m, complete all as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mps as in roof covering /cladding to wall, fixed with self tapping screws as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based plaind steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mps as in roof covering /cladding to wall, fixed with self tapping screws as specified and directed.

0.56mm plain, aluminium sheeting, alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing (length and girth as fixed), complete all as specified and directed. Note: The work is to be carried out upto 10 mtr height.

3mm thick sheet glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.50 Sqm in each pane, complete all as specified and directed.

3mm thick sheet glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares exc 0.50 Sqm in each pane, complete all as specified and directed.

Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos including 5.5 mm thick tinted sheet glass ordinary quality in each door, hinges,anodised aluminum snap beading screws etc. complete all as specified and directed.

2nd class softwood, plain, solid, straight chowkats and frames, wrought, framed, worught, framed rebated on the solid, rounded of chamfered, put together with glue pinned complete all as specified and directed.

35mm thick, 2nd class softwood factory made, plain framed, panelled shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneers on both faces. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated, fitted to chowkats, complete all as specified and directed. 12mm veneered particle board with commercial veneering on both fraces. The size of rail and stile as per IS:1003 (Part1), kiln seasoned and chemically pressure treated complete all as specified.

Factory made solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing shown in SSR Part-II, complete all as specified and directed.

Factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rails and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to in stiles & rails with suitable PVC sheet beading and joinned together with solvent cement supplying & fixing in frames at site as per specification and drawing shown in SSR Part -II, complete all as specified and directed. moulded plain colour PVC channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rails and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to in stiles & rails with suitable PVC sheet beading and joinned together with solvent cement supplying & fixing in frames at site as per specification and drawing shown in SSR Part -II, complete all as specified and directed.

Steel ventilator with top hung shutters including hinges, steel peg stay, complete all as specified and as directed.

3mm thick figured glass pin headed type and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.5 Sqm in each pane complete all as specified and directed.

Galvanised mild steel wire cloth in repair,0.56mm nominal dia of wire and average width of aperture 1.18mm & fixed with stainless steel wire staples, complete all as specified and directed.

Galvanised mild steel wire cloth in repair,0.56mm nominal dia of wire and average width of aperture 1.18mm & fixed with stainless steel wire staples, complete all as specified and directed.

125mm long, mild steel pressed handles, oval type, stove enamelled black, complete all as specified and directed.

150 mm long Mild steel pressed handles, oval type, stove enamelled black.

150mm aluminium anodized barrel tower bolts of extruded section all as specified

250mm size Mild steel sliding door bolts,plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed.

Steel water tubing, 15mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed.

Steel water tubing, 20mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed.

Rotational moulded polythylene 500 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20mm brass ball valve high pressure with brass rod & high density plastic ball including dismantlling of existing tank, complete all as specified and directed.

Rotational moulded polythylene 1000 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20mm brass ball valve high pressure with brass rod & high density plastic ball including dismantlling of existing tank, complete all as specified and directed.

S&F in repair vitreous china, wash hand basin, flat back of size 550mmx400mm with brackets including cutting for and pinning in ends of brackets, including 32mm dia PVC.

S&F in repairs vitreous china squatting pan water closet, orissa pattern, size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) but including PVC (SWR) 'P' trap, jointing to flush pipe complete and making good to floor in cement concrete M-5 (1:5;10), type E-2 using 40mm graded crushed stone aggregate, complete all as specified and directed.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white, including 'P' or 'S' trap, seat cover and fixing bolts, flushing cistern and flush pipe & making good to floor in cement mortar M-15 (1:2:4) type B-1 (using 20mm graded crushed stone aggregated), complete all as specified and as directed.

S&F in repair 10 litre capacity PVC valveless, low level, synphonic action type, flushing cistern, with inlet, ball valve, float valve, handle including brackets, complete all as specified and directed. specified and directed.

S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm, complete all as specified and directed.

S & F in repair 15mm bore bib tap, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule, complete all as specified.

S & F in repair 15mm dia pillar taps, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered 'Hot' and 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs 15mm bore stop valves, fancy type, chromium plated with long long shank and cup (concealed type), cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union, complete all as specified and directed.

S & F in repair for 125mm size brass chromium plated shower rose with or without swivel joints, any size including fixing to steel pipe of 15mm dia or union, complete all as specified.

S&F in repair 20mm bore gun metal globe or gate valve with iron wheel head screwed head both for iron pipe & fixed, complete all as specified and directed.

S&F PVC (SWR) pipes single socketed in any length with rubberring joints laid in trenches 75mm bore, complete all as specified and directed.

S&F PVC (SWR) pipes single socketed in any length with rubberring joints laid in trenches 110mm bore, complete all as specified and directed.

S & F in repair 75mm bore dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints fixed to walls, complete all as specified and directed.

110mm bore dia PVC (SWR) bends, complete all as specified and directed.

75mm bore dia PVC (SWR) bends, complete all as specified and directed.

1.25mm Steel rolling shutters n.exc 7.50 sqm each, with out ball bearing, as specified including stop cover, anchoring rod, hasp and staple and one shop coat of primer erected in position as indicated, complete: push pull or manual type including taking down old shutter, complete oiling ,greecing making smooth functionable up to the desired satisfaction complete all as specified and directed by Engineer-in-Charge.

S&F Safety lever locks mild steel with 4 levers for rolling shutters complete all as spd & directed

S&F Ball bearing for rolling shutters complete all as spd & directed

Preparation of new plastered or unplastered surfaces of wall and applying two coats of cement base paint over a coat of alkali-resistant priming coat, complete all as specified and directed. NOTE: The work is to be carried out upto 10 mtr height.

Preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over chalk whiting, on plastered surfaces preparatory to distempering, complete all as specified and directed.

Preparation of new wooden surfaces of any description not otherwise described, exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

Preparation of new CGI/PGI steel surfaces of any description not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer over a coating of mordant solution including washing the surfaces, complete all as specified and directed.

Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces,complete all as specified and directed. NOTE: The work is to be carried out upto 10 mtr height.

Preparation of old surfaces of walls, plastered or unplastered including brooming down or steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts and trading oil and greasy spots and applying one coat of white or tinted oil bound distemper on walls complete all as specified and directed.

Preparation of old plastered surfaces of wall and applying one coats of cement base paint complete all as spd & directed.

Preparation of old painted wooden surfaces over 10 cm width or girth and applying one coats of synthetic enamel paint complete all as specified.

Taking down light fitting from 9/11 mtr long poles/ security wall fencing and high mast light fitting from any height for repair and checking internal wiring etc. and refixing the same, complete all as specified & directed.

Scraping out the old paint from steel tubular poles by wire brush not more than 9 mtr height above ground level including street light arm and applying two coats of aluminium paint over a coat of primer and marking pole No., complete all as specified and directed.

LED flood light fitting 30 Watt 230 V AC outdoor type, energy saving and environment friendly light fitting with pressure die cast aluminum housing with high power LED flood light luminaires complete with IP66 protection including all accessaries and taking down old existing unsv, complete all as specified and directed.

LED street light fitting 35 Watt 230 V AC outdoor type, energy saving and environment friendly light fitting with electronic geart housed with high pressure die cast aluminum housing LED street light luminaires complete with IP66 protection including all accessaries and taking down old existing unsv, complete all as specified and directed.

LED light fitting 1 x 18 Watt , 4 ' long lighting fixture with extruded Al heat sink , environment friendly , energy efficient ready to use pack including LED tube complete with inbuilt electronic driver , PCB , connector block etc including connecting up with three core twisted flexible copper conductor cable with suitable size LED tube including taking out old, complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and n.exc. 1.5 m deep for foundation of poles/stay/cable etc including getting out in any type of soil complete all as specified and directed.

Excavation in trenches beyond 1.5 m wide and n.exc. 3 m deep for foundation of poles/stay etc including getting out in any type of soil complete all as specified and directed.

Returning filling in (soil) including spreading, levelling , watering and well ramming in layers n exc 25cm thick, complete all as specified and directed.

Removing of surplus soil to a distance n exc 50 mtr and depositing where directed at a level n exc 1.5 mtr above the starting point, complete all as specified and directed.

Sand cushioning to cable with dry fine sand in trenches 8 cm below the cable and 15 cm above the cable after laying, complete all as specified and directed.

Bricks laid in trenches flat with width equal to length of brick for cable protection well burnt sub class 'B' laid across the cable complete all ad specified.

Supply and laying in repairs 40mm dia GI tubing light grade with all fitting laid in trenches or pavement or fixed on wall or along pole complete for protection of GI strip or crossing of nallaj/bridge/road etc., complete all as specified and directed.

Plain cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in foundation/road cutting filling and mass concrete (rounded or chamfered on edges), complete all as specified.

Steel tubular swaged pole with cast iron base plate finial tapper plug, bolts nuts and screws and specified type 410-SP-31 ( 9 Mtr long) in truly vertical position 1.5 m length of pole above ground level shall be painted with two coats of synthetic enamel paint in strips of 30 cm width, black and yellow alternatively and painting with two coats of aluminum paint over a coat of red oxide primer on rest part of pole and its connected parts complete all as specified laying GI pipe light grade for cable protection and fixing to existing pole with flat iron clamp 25x3mm including nuts bolts and washers etc complete of 40mm dia including taking out old unserviceable pole, complete all as specified and directed.

Supply and fixing in repair 1.5 Sqmm three core PVC insulated flexible copper conductor wire for connection of street/security light to terminal box, complete all as specified and directed.

Supply & fix in repair Rigid non-metallic grade PVC conduit of size 20 mm dia, exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc, complete all as specified and directed.

S&F in repair 1100 volt grade heavy duty XLPE cable with PVC insulated aluminium conductor served with inner sheathing of PVC tape armoured with galvanized steel strip or wire and overall PVC sheathed of size 25 sqmm nominal cross section 3.50 core laid in trenches, fixed to pole or passing through pipes including all necessary clamps, nuts, bolts washers complete all as specified and directed. Notes: (i) Earth work and protection work shall be measured and paid for separately under respective items of BOQ. (ii) The cost of thimbles/lugs and cable gland etc. are included in quoated rate and nothing extra will be paid.

S&F in repair 1100 volt grade heavy duty XLPE cable with PVC insulated aluminium conductor served with inner sheathing of PVC tape armoured with galvanized steel strip or wire and overall PVC sheathed of size 16 sqmm nominal cross section 2 core laid in trenches, fixed to pole or passing through pipes including all necessary clamps, nuts, bolts washers complete all as specified and directed. Notes: (i) Earth work and protection work shall be measured and paid for separately under respective items of BOQ. (ii) The cost of thimbles/lugs and cable gland etc. are included in quoated rate and nothing extra will be paid.

S & F in repairs security light brackets, 1.50mtrs long 40mm dia light grade galvanised iron pipe with 30° bend including flat iron clamps, nuts, bolts and washers to brace the same properly duly painted with two coats of silver coloured synthetic enamel paint over one coat of red oxide primer and making the good to disturbed surfaces to match with existing, complete all as specified and directed.

Supply & fixing in replacement of out door type junction box of size 350x350x300 mm made of MS Sheet 1.6mm thick, front door openable with fixing screw painting with two coats of synthetic enamel powder coated paint over a coat of red oxide including alumn bus bar 4 Nos of size 25x3mm mounted on epoxy based post insulators and drilled holes for connection including 1 No MCBs 06 amps incl magnetic lock system all as required and fixed to poles using MS strip of size 32x6mm and nuts & bolts of required size all as required at site or as directed.

Test point terminal block made of gun metal or phosphorus bronze, size 75x75x25mm drilled and screw end connected to Aluminium/GI strips including 3 Nos, 8mm dia, 25mm long hexagonal head screw and fixing of test point with sheet metal enclosure on insulators to isolate from the walls, fixing of insulator on walls using suitable size of screws, washers, gutti/rawal plugs etc. including taking down of old damaged test point terminal block & making good to disturbed surfaces, complete all as specified and directed.

Supply & fixing in repair aluminium strip 25x3mm, incuding epoxy/procelain insulators of suitable size, distance between insulators not more than1mtr including fixing screws, washers etc. complete for PCC block of size 200x200x200mm for RCC roof using screws, washers, gutti/rawal plugs etc., complete all as specified and directed.

Supply & fixing in replacement air termination, single pointed Aluminium rod 12mm dia and 300mm long, including fixing of GI base on epoxy insulators of suitable size to isolate from the roof and fixing of insulators on roof over the purlin using self tapping screws of suitable length or other means to make the roof leakage proof for fixing of air terminal rod and connecting with down/roof conductors, complete all as specified and directed.

40mm bore HDPE non pressure pipe, smooth wall, non-metallic flexible, suitable for underground/wall earthing strip use, pressure rating not less than PN-2.5, minimum wall thickness 2.5mm for protection of GI strip/conductor passing through the wall and from test point upto plinth protection including PVC saddle/clamp, nut bolts etc., complete all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60cmx6mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 meters below normal ground level. connecting to the GI strip 25 x 4mm dia as earth lead by means of bolls, nuts, check nuts and washers of galvanised iron and earth wire protected by provision of GI light grade pipe 15mm bore including provision of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone aggregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM weight not less than 4 Kg/Sqm) and frame of angle iron 25x25x6mm with lugs 02 Nos and handle of 6mm dia MS bar made to shape, GI medium grade 20mm bore pipe for watering , perforated at bottom. 1.75 metre long placed on top edge of earth plate. charcoal and common salt filling with fixing arrangement, funnel wire mesh and earth work in soft soil returning filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electrical plate 3 of SSR-2009 Part-I and connecting to earth test point all as specified or indicated including testing on completion. Notes :- (i) Item of earthing includes cost of 7.5 m long GI wire of size 4 mm dia with protection pipe of 15mm dia GI medium grade, any variation in length shall be adjusted through deviation order based on SSR rates enhanced by (-) 9.00%. (ii) On testing after completion of earthing if the desired earth resistance is not obtained earthing will be re-done by the contractor at his own risk and cost.

M/S TANTRAY AND CO

osho traders

M/S U.K. ENTERPRISES

M/S JAMSHEED ALI CONSTRUCTIONS