Construction of Parking Cum Commercial Complex on Municipal Corporation Land near Chotta Shimla (SH Civil work, open parking, WS and SI, Site development and rain harvesting tank ) ( Under Smart City Project)

Amount

Cutting in earth work in by mechanical in all heights and depths in all kinds of soils, including saturated soils comprising of pick work, jumper work and blasting work both in soft and hard rock with chiseling and wedging out of rock (where blasting is prohibited) and their intermediate classification of soils including, dewatering wherever required, setting of to the required lines, levels as shown on the drawing and directed by the Engineer -in-charge at site., according to the HP.PWD. specification of 1990 (one thousand nine hundred ninety) volume-I (one) and sorting out useful and unuseful material and transportation of the unuseful material for disposing at dumping site (To be arranged by the contractor) as per satisfaction of Engineer- in -charge through all modes of transportation including head load ,animal load or mechanical means along with its leveling fine dressing and with all kinds of labour, machineries, tools equipments and safety measures and incidentals necessary to complete the work by mechanical means and labour ( if required ). All useful material such as stones, shingles aggregate and slates shall be properly stacked at site to the maximum possible extent in all leads and lifts through all modes of transportation as per the directions of the Engineer-in-Charge. The recovery of stones, wheather use full or not, for 125.86 Cum ( One hundred twenty five point eight six cubic metre) @ 300/-(Rupees Three hundred seventy) per Cubic metre shall be effected on pro rata bases in all circumstances. Any loss to the public and private propriety, human being, machinery during the course of execution and disposal of serviceable and nserviceable materials shall be the absolute responsibility of the contractor and shall have to be duly compensated by him in all respects including all incidental charges.

Supply and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. including all lead and lift as per direction of the Engineer-in-Charge

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering: All work up to plinth level 1:5:10 (1 cement : 5 coarse sand): 10 graded stone aggregate 40 mm nominal Size including all lead and lift as per direction of the Engineer-in-Charge

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 cement : 4 coarse sand): 8 graded stone aggregate 40 mm nominal Size) including all lead and lift as per direction of the Engineer-in-Charge

Providing and laying cement concrete in retaining walls,return walls, walls (any thickness) including attachedpilasters, columns, piers, abutments, pillars, posts,struts, buttresses, string or lacing courses, parapets,coping, bed blocks, anchor blocks, plain window sills,fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: including all lead and lift as per direction of the Engineer-in-Charge. (i) 1:3:6 (1 cement : 3 coarse sand) : 6 graded stone aggregate 20 mm nominal size)

Boulder filling behind R/wall or abutment wall including all lead and lift as per direction of the Engineer-in-Charge

Providing and fixing PVC 100 mm dia weep hole pipe in required grade complete in all repsect.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth including all lead and lift as per direction of the Engineer-in-Charge.

Centering and shuttering including strutting, propping etc. and removal of form for including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.(i) Foundations, footings, bases of columns, etc. for mass concrete

Columns, Pillars, Piers, Abutments, Post and struts.

Lintels, beams, plinth beams, girders,bressumers and cantilevers.

Suspended floors, roofs and the like.

Stairs, (excluding landings) except spiral Staircase

Small lintels not exceeding 1.5 m clear span, moulding as in cornices,window sills, string courses, bands, copings, bed plates, anchor blocks and the like.

Edges of slabs and breaks in floors and walls.(a) Under 20 cm wide

wall any thickness

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand) : 4 graded stone aggregate 20mm nominal size). including all lead and lift as per direction of the Engineer-in-Charge

Providing & applying a coat of Dr fixit Fastflex or its equivelent pidiproof LW intgral waterproofing compound confirming to IS 2645 @200 ML for 50 kg of cement 6.5% pidicrete URP after using then cement mortar 1:5 admixture at junction of walls/beam and slab rounded off complete in all respect as per the direction of Engineer-in-Charge.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:1.5:3 (1 cement : 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size) including all lead and lift as per direction of the Engineer-in-Charge

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses,plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement (i)1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies,shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering,shuttering, finish-ing and reinforcement with 1:1.5:3 (1cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size) including all lead and lift as per direction of the Engineer-in-Charge

Steel reinforcement for R.C.C. work including straightening cutting, bending, placing in position and bindig all complete above plinth leve (i) Thermo-Mechanically Treated bars of grade i.Fe-500D or more including all lead and lift as per direction of the Engineer-in-Charge

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) including all lead and lift as per direction of the Engineer-in-Charge

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. In Cement mortar 1:4 (1 cement :4 coarse sand including all lead and lift as per direction of the Engineer-in-Charge

Poviding wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately) including all lead and lift as per direction of the Engineer-in-Charge. (i) 2nd Class Deodar wood.

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in charge. (i) Second class Deodar wood

Providing and fixing 4 mm thick fix glass panes with wood bead etc. complete including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.

Providing and fixing 5 mm thick fix glass panes with wood bead etc. complete including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws :including all lead and lift as per direction of the Engineer-in-Charge

Providing and fixing 2nd class teak wood lipping/ moulded beading or taj beading of size 19X6 mm fixed with wooden adhesive of approved quality and screws/nails on the edges of the Pre-laminated particle board or glazing as per direction of Engineer-in-charge

Providing and fixing 19mm thick water proof commercial board in shelves/box for cup board with butt joints & fixing with nails & screws etc complete) including all lead and lift as per direction of the Engineer-in-Charge

Providing and fixing 19mm thick water proof commercial board in shutter for cup board with butt joints & fixing with nails & screws etc complete) including all lead and lift as per direction of the Engineer-in-Charge

Providing & Fixing decorative high pressure laminated sheet of plan/wood grain in gloss/matt/suede finish with high denisty protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality (i) 1,00mm thick

Providing and fixing maganatic catcher including all lead and lift as per direction of the Engineer-in-Charge

Providing and fixing M.S Eyes and hooks including all lead and lift as per direction of the Engineer-in-Charge

Providing and fixing Aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc.complete including all lead and lift as per direction of the Engineer-in-Charge:(a)300x16mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete Including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (a)200x10 mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete including all lead and lift as per direction of the Engineer-in-Charge : (i)125 mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Providing and fixing flat pressed commercial ply exterior grade (Grade I) or graded wood particle board IS : 3087 marked lining , to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately) :6 mm thick

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position including all lead and lift as per direction of the Engineer-in-Charge (i) Kai wood 2nd class

Providing and fixing 75mmx65mm(seventy five milimetre into sixty five milimetre) moulded hand rail in straight length complete including all lead and lift as per direction of the Engineer-in-Charge

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Steel work i/c hollow section welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. including all lead and lift as per direction of the Engineer-in-Charge(a)In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.(i) 80x1.25 mm M.S. laths with 1.25 mm thick top cover including all lead and lift as per direction of the Engineer-in-Charge

Providing and fixing ball bearing for rolling shutters including all lead and lift as per direction of the Engineer-in-Charge

Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C.slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete including all lead and lift as per direction of the Engineer-in-Charge

Providing and fixing M.S. grills of required approved pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.including all lead and lift as per direction of the Engineer-in-Charge. (a)Fixed to steel windows by welding

Providing and fixing Ist quality ceramic glazed wall tiles of size 20x30cm conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. including all lead and lift as per direction of the Engineer-in-Charge

Providing and laying Precast cement concrte pavers 40 mm thick laid over a bed of cement mortar 1:4 ( one cement :4 sand) 25 mm thick laid in floors, jointed with neat cement slurry mixed with pigment to match the shade of the pavers as per detail of Arch. drg. complete in all respect. including all lead and lift as per direction of the Engineer-in-Charge

Kota stone slabs 20 mm thick in stair steps with single piece having uniform nosing/ edging , laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. (i) kota stone slab 20 mm to 25 mm thick including all lead and lift as per direction of the Engineer-in-Charge

Providing and fixing 18 mm thick Baroda Green Marble saw cut, mirror polished, premoulded and prepolished, machine cut for Wash basin kitchen platforms, vanity counters, window sills,facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. (a)Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble or equivelent. including all lead and lift as per direction of the Engineer-in-Charge

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for in floors, steps of stairs including treads, risers dully making nosing complete in all respect, kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.including all lead and lift as per direction of the Engineer-in-Charge(i) 40 mm thick.

Providing and laying Double charged Vitrified tiles of Kajaria /AGL / NITCO or its equivelent make of approved shade & sample in floor , with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thick-ess,including grouting of joints (Payment for grouting of joints to be made separately) including all lead and lift as per direction of the Engineer-in-Charge. (i) Size of Tile 600x600 mm

Providing and laying Double charged Vitrified tiles of Kajaria /AGL / NITCO or its equivelent make of approved shade & sample with water absorption less than 0.08 % and confor-ming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete including all lead and lift as per direction of the Engineer-in-Charge.(i)Size of Tile 600x600 mm

Providing pre-painted corrugated G.S. sheet roofing(TATA MAKE or its equivlent as approved by the Engineer) including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required including all lead and lift as per direction of the Engineer-in-Charge :i) 0.61 mm thick with zinc coating not less than 275 gm/ m²

Providing pre-painted plain G.S. sheet (TATA MAKE or its equivlent as approved by the Engineer ) ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete:(a)0.63 mm thick with zinc coating not less than 275 gm/m² including all lead and lift as per direction of the Engineer-in-Charge

Providing pre-painted plain G.S. sheet (TATA MAKE or its equivlent as approved by the Engineer) fixing 30 cm wide, 30 cm deep overall semicircular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete:(a)0.63 mm thick with zinc coating not less than 275 gm/m² including all lead and lift as per direction of the Engineer-in-Charge

Providing 2.00 M.S sheet cieling, soffits of chhajas and facia welded over angle/T-iron 25x25x5 mm or as directed by the Engineer complete also applying red lead primer two coats with iron screws or as per drawing in all respect up to all floor levels ( frame work will be paid for separately).including all lead and lift as per direction of the Engineer-in-Charge

Providing and fixing M.S. holder bat clamps of approved design to C.I. or S.C.I. or M.S rectangular rain water pipes embedded in cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good the walls etc including all lead and lift as per direction of the Engineer-in-Charge. :(i) 100 mm diametre.

Poviding and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type B,including jointing with seal ring conforming to IS : 5382,leaving 10 mm gap for thermal expa-nsion, (i) Single socketed pipes.including all lead and lift as per direction of the Engineer-in-Charge. (i)110 mm diameter

(ii) Coupler. (a) 110 mm

(iii) Shoe. (a) 110 mm

(iv) Bend 87.5 degree or required degree .(a)110 mm bend

Poviding and fixing in trench unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type B,including jointing with seal ring conforming to IS : 5382,leaving 10 mm gap for thermal expa-nsion,( earth work will be meausre and paid for separately) (i) Single socketed pipes.i)150 mm diameterincluding all lead and lift as per direction of the Engineer-in-Charge

6 mm cement plaster of mix :1:3 (1 cement : 3 course sand) upto all floor height and floor levels.including all lead and lift as per direction of the Engineer-in-Charge

20 mm cement plaster on rough side of brick masonry or stone masonry wall upto all floor level and height:(a)1:6 (1 cement: 4 coarse sand) including all lead and lift as per direction of the Engineer-in-Charge

15 mm cement plaster on fair of brick masonry or stone masonry wall upto all floor level and height:(a)1:4 (1 cement: 4 coarse sand) including all lead and lift as per direction of the Engineer-in-Charge

20 mm cement plaster in Pattern on wall or window bands etc. as per Arch. Drawing on fair or rough side of brick masonry or stone masonry wall upto all floor level and height including all lead and lift as per direction of the Engineer-in-Charge

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.including all lead and lift as per direction of the Engineer-in-Charge

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.with water thinnable cement primer on wall surface having VOC content less than 50 grams/litre including all lead and lift as per direction of the Engineer-in-Charge

Finishing walls with 100% Premium acrylic exterior emulsion/Acrlyck interiolr paint of Asian /Nerolac / Dulux having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.including all lead and lift as per direction of the Engineer-in-Charge.(a)New work (Two or more coats applied @ 1.43 litre/ 10 sqm. over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.

Finishing walls with 100% Premium acrylic exterior emulsion/Apex Ultima weather proof paint of Asian /Nerolac / Dulux having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.including all lead and lift as per direction of the Engineer-in-Charge.(a)New work (Two or more coats applied @ 1.43 litre/ 10 sqm. over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications including carriage of materials in all leads and lifts by mechanical or manual means :(i) Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture including carriage of materials in all leads and lifts by mechanical or manual means.including all lead and lift as per direction of the Engineer-in-Charge.

Applying priming coat on wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture.including all lead and lift as per direction of the Engineer-in-Charge

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture.including all lead and lift as per direction of the Engineer-in-Charge

French sprit polishing on new wood work ( Two or more coats on new works including a coat of wood filler) of approved brand and manufacturere complete in all respect at all heights and floor levels.including all lead and lift as per direction of the Engineer-in-Charge

Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 75 mm to /150 mm dia PVC pipes conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-in-charge.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with squatting pan or European type water closet (Anglo Indian W.C pan of Cera or Hindware or its equivlent make ) of white shade or as per approved sample with seat & lid fixed with C.P. brass hinges and rubber buffers, 10 litre low level flushing cistern No.21001 with fitting and brackets, 40 mm flush bend, 20 mm over flow pipe, with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: including all lead and lift as per direction of the Engineer-in-Charge

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:(a)White Vitreous China Wash basin No. 10001 of size 550x400 mm with a 15 mm CP Brass single hole basin mixer of Cera ,Hindware or its equivlent make including all lead and lift as per direction of the Engineer-in-Charge.

Providing and fixing Fixing white pedestal for wash basin completely recesed at the back for reception of pipes and fittings:including all lead and lift as per direction of the Engineer-in-Charge

Providing and fixing PVC floor trap of approved quality & make complete in all respect including all lead and lift as per direction of the Engineer-in-Charge.(i)100 mm dia metre.

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white pvc automatic flushing cistern,with fittings,standard size cp brass flush pipe, spraders with unions and clamps all in cp brass with waste fittings as per IS- 2556, CI trap with outlet grating and other couplings in CP brass including painting fo fittings and cutting and making good the walls and floors where ever required:single half stall urinal with 5 litre pvc automatic flushing cistern including all lead and lift as per direction of the Engineer-in-Charge.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge including all lead and lift

Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan.including all lead and lift as per direction of the Engineer-in-Charge

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. including all lead and lift as per direction of the Engineer-in-Charge(a)Semi Rigid 40mm dia

Providing and fixing 100 mm C.P grating for gully/ floor trap including all lead and lift as per direction of the Engineer-in-Charge

Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design including all lead and lift as per direction of the Engineer-in-Charge

Providing and fixing 600x450 mm beveled edge mirror ofsuperior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P.brass screws and washers complete including all lead and lift as per direction of the Engineer-in-Charge.

Providing and fixing toilet paper holder including all lead and lift as per direction of the Engineer-in-Charge :(A) C.P. brass

Providing and fixing on under ground waste unplasticised Rigid PVC pipes conforming to IS : 13592 Type B of Supreme /Finolex make including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipe (i) (150 mm diameter overall size having 2.7 mm thickness) including all lead and lift as per direction of the Engineer-in-Charge

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC waste pipes conforming to IS : 13592 Type B of Supreme /Finolex make , including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion: including all lead and lift as per direction of the Engineer-in-Charge.(a) Plain bend or required degree(i) 150mm dia

(b) Single Tee with Door(i) 150X150X150mm

(c) Single Tee without Door (ii)150X150X150mm

Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand):including all lead and lift as per direction of the Engineer-in-Charge.(i) 150mm dia

(ii) 100 mm Dia

Providing and fixing charomium plated brass soap dish with C.P. Brass brackets fixed to wooden cleats with C.P. Brass screws of required size and shape. including all lead and lift as per direction of the Engineer-in-Charge

Providing and fixing PTMT shelf 440 mm long, 124 mm width and 36 mm height of approved quality and colour, weighing not less than 300 gms.including all lead and lift as per direction of the Engineer-in-Charge

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete including all lead and lift as per direction of the Engineer-in-Charge :(i)20 to 40 mm nominal bore

Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete (cost of water meter and stop cock to be paid separately).including all lead and lift as per direction of the Engineer-in-Charge

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.including all lead and lift as per direction of the Engineer-in-Charge(i) 20 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work including all lead and lift as per direction of the Engineer-in-Charge- (i) 20 mm dia

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work including all lead and lift as per direction of the Engineer-in-Charge- (i)15mm (fifteen millimetre) nominal bore .

Providing and fixing Polyethelene-Aluminium Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including ball special fittings of composite material engin-eering plastic blend and brass inserts wherever required) e.g.elbows, tees, reducers, couplers & conne-ctors etc., with trenching, refilling and testing of joints complete including all lead and lift as per direction of the Engineer-in-Charge.(i)1216 ( 16 mm OD) pipe.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, Sintex or its equivlent make with cover and suitable locking including all lead and lift as per direction of the Engineer-in-Chargearrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.including all lead and lift as per direction of the Engineer-in-Charge

Providing and fixing Chromium plated brass ISI marked IS No.8931 of JAL/ESS ESS make or its equivelent bib cockincluding all lead and lift as per direction of the Engineer-in-Charge (i) :15 mm nominal bore

Providing and fixing brass full way valve with wheel including carriage of materials within all leads and lifts :-(i)15mm nominal bore :-

(ii)20mm nominal bore

Providing and fixing Chromium plated brass ISI marked IS No.8931 of JAL/ESS ESS make or its equivelent stop cock .including all lead and lift as per direction of the Engineer-in-Charge(i) 15 mm nominal bore

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) or any required sizes of approved make and quality as per direction of Engineer-in-charge.

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. 25 mm nominal bore, 152mm long, weighing not less than 440 gms including all lead and lift as per direction of the Engineer-in-Charge

Providing and fixing uplasticised PVC connection pipe with brass union (i) 20mm nominal bore 45 cm length

providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C.waste fittings complete.including all lead and lift as per direction of the Engineer-in-Charge

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 600x600 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 Fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:Inside dimensions 455x610 mm and 45 cm deep for single pipe line :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5. With common burnt clay F.P.S.(nonmodular) bricks of class designation 7.5 including all lead and lift as per direction of the Engineer-in-Charge

onstructing masonry Chamber 90x90x100 cm inside, inbrick work in cement mortar 1:4 (1 cement : 4 coarsesand) for sluice valve, with C.I. surface box 100 mm topdiameter, 160 mm bottom diameter and 180 mm deep(inside) with chained lid and RCC top slab 1:2:4 mix (1cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ), i/c necessary excavation, foundationconcrete 1:5:10 (1 cement : 5 fine sand : 10 gradedstone aggregate 40 mm nominal size ) and insideplastering with cement mortar 1:3 (1 cement : 3 coarsesand) 12 mm thick, finished with a floating coat of neatcement complete as per standard design :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5. With common burnt clay F.P.S.(nonmodular) bricks of class designation 7.5

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. Complete including all lead and lift as per direction of the Engineer-in-Charge (New work) :(i)15 mm nominal bore

(ii)20mm nominal bore

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : (i) 15 mm diameter pipe

20 mm dia.

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc.and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4(1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size),including finishing complete so as to make it leak proof.ncluding all lead and lift as per direction of the Engineer-in-Charge

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design(i)100x100 mm size P type.(i) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including all lead and lift as per direction of the Engineer-in-Charge

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : (i)Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : (i) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including all lead and lift as per direction of the Engineer-in-Charge

Providing and fixiung 600 mm dia metre RCC cover of NTC make or its equivelent complete including of its steel frames as required at site .including all lead and lift as per direction of the Engineer-in-Charge

Tenzin Construction Co. Pvt. Ltd.