Up-gradation of Zorawar and Shivaji Hall of Training Centre at NSG Camp Manesar.

EARTH WORK

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge.

All kinds of soil

Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti- termite treatment (excluding the cost of chemical emulsion) : Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration.

CONCRETE WORK

Providing and laying in position excluding cement concrete of level: specified grade the cost of centering and shuttering - All work up to plinth.

1:1.5:3 (1 Cement: 1.5 coarse sand (zone-Ill) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

1:2:4 (1 cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

1:5:10 (1 cement : 5 coarse sand (zone-Ill) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement: 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 12.5 mm nominal size derived from natural sources).

REINFORCED CEMENT CONCRETE

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :

1:1.5:3(1 cement: 1.5 coarse sand (zone-Ill) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement:

1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form for

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

MASONARY WORK

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:

Cement mortar 1:6(1 cement :6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :

Cement mortar 1:6(1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.

Cement mortar 1:4(1 cement :4 coarse sand)

Extra for providing and placing in position 2 Nos 6 mm dia. M.S. bars at every third course of half brick masonry.

CLADDING WORK

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.

Granite stone slab of colour black, Cherry/Ruby red

Area of slab upto 0.50 sqnn

Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Granite work

WOOD AND P.V.C. WORK

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :

Providing and fixing stainless steel fancy handle of approved make fixed with SS screws etc. complete as per direction of Engineer-in-charge.

Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and lnline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for (i) Sites with basic wind speed > 45 m/sec as per IS 875 — Part 3 (ii) Sites with structure height more than 20m for all wind speeds

Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body.

Using R3 series with frame (98 mm & above) x (40 mm & above) & both glazed and fly screen sash (30 mm & above) x (55 mm & above) with zinc alloy (zamak) powder coated handle on every glazed panel along with multi-point locking system. (Height upto 1.8m).

Fixed window/ ventilator without mullion /transom.

Using R1 series with frame (33 mm & above) x (35 mm & above). (Height upto 0.90 metre)

STEEL WORK

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Hot finished welded type tubes

FLOORING

Providing and laying full body vitrified tile in floor of minimum thickness 15 mm with water absorption less than 0.06% and conforming to IS:15622, of approved make, brand and manufacturer, laid on 20 mm thick base cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.30 kg / sqm including grouting the joints with white cement and matching pigments etc. The slab must be cut with the zero chipping diamond cutter only. Laying of slab will be done with the help of notch trowel, wedge, clips of required thickness, vacuum cups for lifting, leveling system and rubber mallet for placing the slab gently and easily. Size of tile 800x2400 mm of all colours and shades.

Deduct for not using 20 mm thick cement mortar 1:4 (1 cement : 4coarse sand) bedding in laying of floor tiles and jointing with grey cement slurry @ 3.3kg/sqm

Fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3mm thickness.

ROOFING

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS :5382, leaving 10 mm gap for thermal expansion.

Coupler

Single tee with door

Single tee without door

110 mm bend

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'S or 'L' hooks, bolts & nuts 8 mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafers, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified.

2 mm thick corrugated (2.5" 0r 4.2" or 6") or step-down (2" or 3" or 6" ) as specified

FINISHING

12 mm cement plaster of mix:

1:6 (1 cement: 6 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix:

1:6(1 cement: 6 coarse sand)

15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix:

1:4(1 cement: 4 fine sand)

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:

New work (Two or more coats applied @ 1.43 Itr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

Two or more coats on new work

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

REPAIR TO BUILDINGS

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge.

With cement mortar 1:4 (1cement: 4 coarse sand)

Disconnecting damaged overhead/terrace PVC water storage tank of any size from water supply line and removing from the terrace including shifting at ground level as per direction of Engineer-in-charge.

Dismantling W.C. Pan of all sizes including disposal of dismantled materials including malba all complete as per directions of Engineer-in-Charge.

DISMANTLING AND DEMOLISHING

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

Nominal concrete 1:3:6 or richer mix (including equivalent design mix)

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.

In cement mortar

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :

Of area beyond 3 sq. metres

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.

For thickness of tiles 10 mm to 25 mm

Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead

Demolishing mud phaska in terracing and disposal of material within 50 metres lead.

Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50metres lead : Up to 10 mm thick

Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead.

Dismantling C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead :

100 mm dia pipe

Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge :

15 mm to 40 mm nominal bore

Dismantling C.I. pipes including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means breaking lead caulked joints, melting of lead and making into blocks including stacking of pipes & lead at site within 50 metre lead as per direction of Engineer-in-charge:

Up to 150 mm diameter

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

ROAD WORK

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.

80 mm thick C.C. paver block of M-35 grade with approved colour design and pattern.

SANITARY INSTALLATIONS

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

WATER SUPPLY

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

20 mm nominal dia Pipes

25 mm nominal dia Pipes

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Internal work - Exposed on wall

20 mm dia nominal bore

25 mm dia nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions :

45 cm length

15 mm nominal bore

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in reinforced cement concrete slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), including necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :

With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :

20 mm nominal bore

25 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

15 mm nominal bore

DRAINAGE

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

ALUMINIUM WORK

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer- in-charge.

With stainless steel cover plate minimum 1.25 mm thickness

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

WATER PROOFING

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.

(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.

(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge.

(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.

(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. “All above operations to be done in order and as directed and specified by the Engineer-in-Charge :

With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge. With fully perforated 12 mm thick micro tegular edged or 10 mm thick square edged GRG false ceiling tiles.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

30 mm thick

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed in position with M.S hold fast/ lugs/ SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/ window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variationin profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Frame size 65 x 125 mm

Add correction factor 0.973 (i.e. 2.70%) on DSR items @ total of DSR rates x 2.70% i.e. 11192729.81X2.70%= -302203.70

Add Cost index on DSR 2023 @ 4.03%on 10890526.11= 438888.20

NON-SCHEDULE ITEMS

Providing and fixing Door lock patch fitting on existing Toughened glass shutter complete as per the architectural drawings and the directions of engineer-in-charge .

Providing and fixing Stainless steel H -type handle on existing toughtend glass shutter including holing/drilling etc all complete as per the directions of engineer-in-charge .

Providing and fixing Outdoor golden LED Signage "Zorawar Hall" and both side Logo (NSG EMBLEM) make of stainless steel 304 grade, 20 guage, Letter Size 15`` logo size 24x24``, depth approx 1.75 to 2``, PVD coated acrylic 010 3mm back side double channel letter with LED lighting of 3 year warranty, warm white colour including power supply fixures etc of one year warranty including drilling , holling in granite/RCC etc all complete as per direction of Engineer In charge.

Providing and fixing Outdoor golden LED Signage "Shiwaji Hall" and both side Logo (NSG EMBLEM) make of stainless steel 304 grade, 20 guage, Letter Size 15`` logo size 24x24``, depth approx 1.75 to 2``, PVD coated acrylic 010 3mm back side double channel letter with LED lighting of 3 year warranty, warm white colour including power supply fixures etc of one year warranty including drilling , holling in granite/RCC etc all complete as per direction of Engineer In charge.

Providing & fixing of 06mm thick both side High pressure Exterior Grade laminate of approved quality & make . These are EN 438-Part 6 complying panels, which are manufactured by high pressure and temperature in a hot press. The core of the panel consists of desired numbers of imported, long fibre virgin kraft papers, impregnated with specially formulated double hardened Phenolic resin and another top layer of imported virgin Blue wool scale passed, decorative paper layer impregnated with melamine resin. The panels are flame retardant type class 1 as per BS:476 Part 7, ASTM E84 and EN 438-Part 6. Poly-methyle methacrylate UV protecting films are provided at the top of the Deco layer for optimum UV protection (passes 1500Hrs). HPL panels have a tested Flexural Modulus of ≥ 11,000 MPa and Flexural strength of ≥ 100 MPa which makes the product enormously sturdy from inside. This product shows no distortion in extreme climatic changes such as from -20°C to +80°C or from dry climate to a relative humidity in excess of 85% - 90%. HPL panels are equipped with a maximum possible weather resistance at extreme oceanic climates as it has duly passed the salt spray test conducted for 500 Hours. HPL panels pass a 3000 hours artificial weathering and are rated with a 5 for Grey scale rating & 7/8 for Blue wool rating. Density is 1.45gm/cm3 with 10 years warranty the cladding system will be installed on aluminium frame work on wall or other surface for making grid of maximum size of 600x600mm(c/c) as frame work wall lining work using rectangular section of size 38.10x25.40x1.44mm or other equivalent sections of approved make conforming to IS:1285 i/c providing & fixing with SS Anchor/dash/wedge fasterners or required dia nd size, scaffolding etc. Aluminium sections shall be smooth , rust free, straight, mitres or unshared and jointed mechanically wherever required including cleat angle,etc. all complete as per architectural drawing and as per direction of engineer-in-charg.Installation will be done via rivets/adhesive and 3M tape.

Providing and fixing Premium quality GRC cobbles of size not less than 150x150x22 mm of approved design and shape laid in required colour and pattern in footpath & courtyard etc jointed with neat cement slurry mixed with pigment to match the shade of tiles, including cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).

Providing and fixing Premium quality Glazed vitrified wall tiles polished finish of size (GVT) size not less than 600x1200 with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing 'Unistone', make or equivalent Glass Reinforced Concrete (G.R.C) Screens casted with 'Spray Mix' concrete design in approved size, pattern, thickness of 50mm on the outer Border & 25-30mm for Internal member or overall thickness of 40mm and shade. The Screens should be made from ‘43 grade’ Portland Cement manufactured by ‘JK Cement’ or ‘Nuvoco’ or ‘JK Lakshmi’ or Ultratech', White Quartz fine graded sieve Silica Sand, Alkali Resistant Glass Fibre manufactured by 'NEG Japan, Owen Corning ‘Saint Gobain’ or equivalent, Super Plasticizers manufactured by ‘Karochem’ or equivalent, Polymers manufactured by ‘Nova Polychem’ or equivalent and U.V resistant Synthetic inorganic pigments should be used for pigmentation manufactured by ‘Phenochem industries or equivalent. The Screens casting shall take place with layering methodology using- Direct Power Spray machines. The GRC Screens flexural strength average L.O.P should be above or equivalent to 6 N/mm² & M.O.R should be above or equivalent to 12 N/mm² for tests done on 28 days cured samples. The fixing of Screens should be done using ‘Dry fixing’ method onto structural support members i.e. R.C.C, Brick work MS Framework. MS Galvanized CLAMPS & PINS also if required fasteners to be used of Wurth, Hilti & Fischer or equivalent. ALL CAST in SOCKET TO BE EPOXY PRIMER COATED. ELECTRODES to be used of ADVANI, MANGALAM, ESAB OR Victor brand or equivalent. Vendor shall submit shop drawings of same, the drawings to be duly approved from Engineer in charge at site.

Providing and fixing of Fabric Acoustical Wall Paneling in all heights with square edges made of Rockwool with Glasswool Tissue substrate 25mm thick and wrapped on the front side with an acoustically transparent and fire-resistant fabric with an option of colors as per the choice of the Architect/ Engineering- in charge of size 600x1200 or 600x600 mm providing a minimum sound absorption level of 0.90 NRC. The GI stud system includes G.I Stud having Size 48 mm X 36 mm X 34 mm X 0.50mm, length 3600mm, and Floor Channel Size 50 mm X 32 mm X 32 mm X 0.50 mm, length 3600 mm is fastened vertically/ horizontally at every 600mm filled with 50mm 1000GSM non-woven thermal bonded polyester wadding. Then 8 mm Gyptech HDMR Board Perforated strips of 100 mm should be Screwed to the GI frame with the help of 25 X 6 mm metal screw 25mm thick fabric acoustical panel should be pasted on the 8 mm HDMR Board strips with the help of rubber base Adhesive including scaffolding etc complete as per drawing and design approved by Engineer-in-Charge. Make: Armstrong / Anutone/Gyptech or equavalent (Manufacturer Company MTC along with NRC certificate would be required at the time of installation).

Providing and fixing uPVC soffit panel of size 288mm width and 1.5mm thick in wall lining on existing aluminium frame work. Panel should have one side decorative other side balacing design, with necessary fixing arrangment and screw etc and as per direction of engineer in charge.

Providing and fixing white vitreous china table top wash basin of catagery JDS-WHM-25907N of Jaquar make or equavalent series of make cera, hindware, Parryware with 32mm CP Brass Waste of standard pattern including making all connections : Italian collection as per direction of engineer in charge Table Top Basin, In White Matt of Size: 530x420x140 mm, Shape - Rectangular as per direction of engineer in charge all complete

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of Size: 370x665x750 mm of catagery CNS-WHT-853S220SPPSM of Jaquar make or equavalent series of make cera, hindware, Parryware including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge.

Providing and fixing single lever Basin mixture of catagery KUP-35005BPM of Jaquar make or equavalent series of make cera, hindware, Parryware including painting of fittings and brackets, cutting and making good the walls wherever required:-

Providing & Fixing toilet cubicals of approved make e.g.Greenlam, Action tesa or Duro etc of size 1303x1500x1885 with thickness of panels is 12mm and door size 600x1730 make solid compact laminate consists of layer of cellulose fibrous materal impregnated with thermosetting resin and bonded togther by the high pressure process. the surface of the both side, having decorative colours or design, are impregnated with melamine based resins. including SS 316 round top rail, Noise deafening tape, SS 316 coat Hook with Stopper, SS 316 concealed hinge ,SST 316 door knob, SST 316 door stopper channel SS 316 head rail, tabular holder, SS hollow section wall bracket, SS 316 screw, SS 316 shoe box side cover, SS 316 thumb turn lockset & U channel, complete in all respect as per direction of Engineer-in-Charge.

Excavating, supplying and filling of Malba by mechanical transport upto a lead of 5km also including ramming and watering of the malba in layers not exceeding 20 cm in floor, trenches, plinth, sides of foundation etc. complete.

«
Providing and fixing anodised

汢⁥慢瑴牥⁹湡⁤湩楤慣楴湯映牯爠汥祡猠慴畴⁳⽩⁣牰杯慲浭湩⁧瑡猠瑩⁥潣灭敬整愠⁳敲畱物摥‮7㄀漠瑵異⁴数⁲桰獡⁥湡⁤畳瑩扡敬映牯猠湩汧⁥桰獡⁥畳灰祬űĈ匀灵汰楹杮‬湩瑳污慬楴湯‬整瑳湩⁧湡⁤潣浭獩楳湯湩⁧景倠獡楳敶䤠普慲敲⁤倨剉 整档潮潬祧戠獡摥漠捣灵湡祣猠湥潳⁲慨楶杮栠杩⁨数晲牯慭据ⱥ渠湯爠来汵瑡湩⁧牰杯慲浭扡敬琠灹ⱥ猠極慴汢⁥潦⁲潣湮捥整⁤潬摡甠瑰〱流Ɒ映牯洠畯瑮湩⁧敨杩瑨甠⁰潴㌠洠牴愠摮映牯㔠洠搠慩敭整⁲潣敶慲敧愠敲⁡污湯⁧楷桴渠捥獥慳祲映硩湩⁧牡慲杮浥湥獴椠振瀠潲牧浡業杮愠⁴楳整攠捴‮潣灭敬整愠⁳敲畱物摥‮Űç匀灵汰楹杮愠摮䰠祡湩⁧景漠敮渠浵敢⁲污浵湩畩潣摮捵潴Ⱳ堠偌⁅湉畳慬整Ɽ倠䍖猠敨瑡敨Ɽ愠浲畯敲⁤潰敷⁲慣汢⁥景ㄠㄮ欠⁖牧摡⁥‬潣普物業杮琠卉㨠㜠㤰‸倨牡⵴⤱ㄠ㠹‸景映汯潬楷杮猠穩⁥湩琠敨攠楸瑳湩⁧䍒⽃䠠䵕⽅䴠呅䱁瀠灩⁥獡爠煥極敲⹤㌀㔮砠†〵猠浱཭⸳‵⁸ㄠ〲猠浱ၭ⸳‵⁸†㔱‰煳浭á匀灵汰楹杮‬慌楹杮愠摮映硩湩⁧景漠敮渠浵敢⁲潣灰牥挠湯畤瑣牯‬䱘䕐䤠獮汵瑡摥‬噐⁃桳慥桴摥‬牡潭牵摥瀠睯牥挠扡敬漠⁦⸱‱噫朠慲敤Ⱐ挠湯楦浲湩⁧潴䤠⁓›〷㠹⠠慐瑲ㄭ 㤱㠸漠⁦潦汬睯湩⁧楳敺漠慷汬猠牵慦散䌯扡敬琠慲⁹獡爠煥極敲⹤㐀⁣⁸㔲猠⹱洠๭挴砠ㄠ‶煳‮浭㐀⁣⁸〱猠⹱洠詭畓灰祬湩⁧湡⁤楦楸杮映汯潬楷杮猠穩⽥洠摯汵獥‬䥇戠硯愠潬杮楷桴洠摯汵牡戠獡⁥…潣敶⁲汰瑡⁥潦⁲潭畤慬⁲睳瑩档獥椠敲散獳攠捴‮獡爠煥極敲⹤㄀漠⁲′潍畤敬⠠㔷浭㝘洵⥭¤匀灵汰楹杮愠摮映硩湩⁧潦汬睯湩⁧潭畤慬⁲睳瑩档 潳正瑥漠桴⁥硥獩楴杮洠摯汵牡瀠慬整☠猠楷捴⁨潢⁸湩汣摵湩⁧潣湮捥楴湯⁳畢⁴硥汣摵湩⁧潭畤慬⁲汰瑡⁥瑥⹣愠⁳敲畱物摥ᜮ敔敬桰湯⁥潳正瑥漠瑵敬畓灰祬湩Ⱨ䰠祡湩⁧湡⁤楦楸杮漠⁦湯⁥畮扭牥猠牴湡敤⁤潣灰牥挠湯畤瑣牯‬䱘䕐䤠獮汵瑡摥‬噐⁃桳慥桴摥‬牡潭牵摥瀠睯牥挠扡敬漠⁦⸱‱噫朠慲敤Ⱐ挠湯楦浲湩⁧潴䤠⁓›〷㠹⠠慐瑲ㄭ 㤱㠸漠⁦潦汬睯湩⁧楳敺椠桴⁥硥獩楴杮倠䍖 䕍䅔⁌楰数愠⁳敲畱物摥㐮″⁣⁸⸲‵煳‮浭⠠潣浭湵捩瑡潩慣汢⁥潦⁲䑏⁕…䑉⥕"㐀挠砠㐠〮猠⹱洠瀨睯牥挠扡敬䤠啄〈‴⁣⁸〱〮猠⹱洠瀨睯牥挠扡敬传啄〈‴⁣⁸㘱〮猠⹱洠瀨睯牥挠扡敬传啄윩畓灰祬湩⁧湡⁤楦楸杮漠⁦潦汬睯湩⁧楳敺⁳景映敬楸汢⁥瑳敥潣摮極⁴污湯⁧楷桴愠捣獥潳楲獥椠畳晲捡⽥敲散獳椠据畬楤杮挠瑵楴杮琠敨眠污湡⁤慭楫杮朠潯⁤桴⁥慳敭椠慣敳漠⁦敲散獳摥挠湯畤瑩愠⁳敲畱物摥찮畓灰祬湩⁧湡⁤楦楸杮映汯潬楷杮猠穩獥†䱄⁐ⵕ噐⁃琠畲歮湩⁧眠瑩⁨潣敶Ⱳ猠灥牡瑡牯瀠牡楴楴湯愠摮†捡散獳牯敩⁳䨨楯瑮ⱳ䄠杮敬ⱳ䈠湥獤‬湅⁤慃獰‬牂捡敫獴‬畊据楴湯⁳瑥⥣漠畳晲捡⁥瑥⁣潣灭敬整愠⁳敲畱物摥ਮ㄀㔰洠⁸〵洠㈨挠浯慰瑲敭瑮⥳ŵ匀灵汰楹杮愠摮氠祡湩⁧景映汯潬楷杮猠穩⁥坄⁃䑈䕐瀠灩⁥卉⁉慭歲摥愠潬杮眠瑩⁨污捡散獳牯敩⁳楬敫猠捯敫ⱴ戠湥Ɽ挠畯汰牥⁳瑥⹣挠湯潦浲湩瑧卉ㄠ㤴〳‬慐瑲䤠潣灭敬整眠瑩⁨楦瑴湩⁧湡⁤畣瑴湩Ⱨ樠楯瑮湩⁧瑥⹣楤敲瑣椠牧畯摮⠠㔷挠敢潬⁷牧畯摮氠癥汥 湩汣摵湩⁧硥慣慶楴湯愠摮爠晥汩楬杮琠敨琠敲据⁨畢⁴硥汣摵湩⁧慳摮挠獵楨湯湩⁧湡⁤牰瑯捥楴敶挠癯牥湩⁧瑥⹣挬浯汰瑥⁥獡爠煥極敲⹤'㘀″浭搠慩⠠䑏㘭″浭☠䤠ⵄㄵ洠潮業慮⥬'㤀‰浭搠慩⠠䑏㤭‰浭☠䤠ⵄ㘷洠潮業慮⥬*㄀〲洠楤⁡伨ⵄ㈱‰浭☠䤠ⵄ〱″浭渠浯湩污﨩畓灰祬湩⁧湡⁤慬楹杮漠⁦潦汬睯湩⁧楳敺䐠䍗䠠偄⁅楰数䤠䥓洠牡敫⁤污湯⁧楷桴愠汬愠捣獥潳楲獥氠歩⁥潳正瑥‬敢摮‬潣灵敬獲攠捴‮潣普牯業杮琠卉ㄠ㤴〳‬慐瑲䤠⁉潣灭敬整眠瑩⁨楦瑴湩⁧湡⁤畣瑴湩Ⱨ樠楯瑮湩⁧瑥⹣椠桴⁥硥獩楴杮琠敲据ⱨ挠浯汰瑥⁥獡爠煥極敲⹤ώ吀敨爠慯⁤牣獯楳杮⁳景瀠睯牥挠扡敬†桴潲杵⁨牴湥档敬獳戠牯湩⹧†牔湥档敬獳栠牯穩湯慴潢楲杮甠楳杮䴠湡慵⽬䴠捡楨敮䴠汯湩⁧整档楮畱⁥愠⁴⸰㔷洠瑥敲戠汥睯琠敨朠潲湵⁤敬敶潦⁲潦汬睯湩⁧楳敺瀠灩獥‬椠据畬楤杮猠牵敶⁹景甠摮牥朠潲湵⁤琠汩瑩敩ⱳ†硥慣慶楴湯漠⁦楰獴‬洠汯湩⁧楷桴琠敨栠汯⁥楳敺渠瑯攠捸敥楤杮㈠┰漠⁦桴⁥楰数搠慩‬戠捡晫汩楬杮‬潣灭捡楴湯愠摮爠獥潴慲楴湯漠⁦桴⁥楰獴琠牯杩湩污挠湯楤楴湯攠捴‮獡爠煥極敲⹤吠敨爠瑡獥映牯洠汯湩Ⱨ愠⁳湩楤慣整⁤牡⁥湩汣獵癩⁥景†捸癡瑡潩景瀠瑩ⱳ戠捡晫汩楬杮‬潣灭捡楴湯愠摮†敲瑳牯瑡潩景琠敨瀠瑩⁳潴漠楲楧慮潣摮瑩潩⹮䄠祮搠浡条獥漠捣牵敲⁤潴漠桴牥甠楴楬楴獥搠牵湩⁧桴⁥潍楬杮漠数慲楴湯猠慨汬戠⁥浩敭楤瑡汥⁹潮楴楦摥愠摮爠捥楴楦摥戠⁹桴⁥潣瑮慲瑣牯眠瑩潨瑵愠祮挠獯⁴浩汰捩瑡潩潴琠敨䐠灥牡浴湥⹴†桔⁥敬杮桴漠⁦桴⁥潈敬⠠硥汣摵湩⁧桴⁥楳敺⁳景琠敨瀠瑩⁳湯戠瑯⁨湥獤 桳污敢挠湯楳敤敲⁤潦⁲桴⁥敭獡牵浥湥⁴景䴠汯湩⁧敬杮桴‮潈敷敶Ⱳ椠瑮牥敭楤瑡⁥楰獴眠汩潣獮摩牥椠桴⁥潭楬杮氠湥瑧⹨椊 唠瑰〲‰浭搠慩䐠䍗䠠偄⁅ ⹇⹉⼠噐⩃
畓灰祬湩⁧湩瑳污慬楴湯琠獥楴杮愠摮挠浯業獳潩楮杮漠⁦〴洰睳敥⁰慷汬映湡眠瑩⁨桴牥慭癯牥潬摡洠瑯牯瀠潲整瑣潩Ɱ搠汥癩牥⁹慲整㠠‵䵃⁍瑡ㄠ㌳‰灲漨⁲敢瑴牥 畳瑩扡敬映牯漠数慲楴湯漠㈠〲㈭〴⁖湡⁤〵穈䄠⁣畳灰祬攠捴爠煥極敲⹤††††††††††††††††††††††††††††††††††††Ç匀灵汰楹杮愠摮洠歡湩⁧湥⁤整浲湩瑡潩楷桴戠慲獳挠浯牰獥楳湯朠慬摮愠摮愠畬業楮浵氠杵⁳潦⁲潦汬睯湩⁧楳敺漠⁦噐⁃湩畳慬整⁤湡⁤噐⁃桳慥桴摥⼠堠偌⁅污浵湩畩潣摮捵潴⁲慣汢⁥景ㄠㄮ䬠⁖牧摡⁥獡爠煥極敲⹤㐀堠㈠‵煳‮浭⠠㠲浭ᐩ‴⁘㘱猠⹱洠㈨洸⥭㐀堠ㄠ‰煳‮浭⠠㔲浭ᔩ⸳‵⁸㔠‰煳浭⠠㔳浭ᘩ⸳‵⁸ㄠ〲猠浱㐨洵⥭㌀㔮砠†ㄠ〵猠浱㔨洰⥭҉匀灵汰ⱹ䤠獮慴汬瑡潩Ɱ吠獥楴杮愠摮䌠浯業獳潩楮杮漠⁦㈱〰洠睳敥Ɒ䈠䕅㔠猠慴⁲慲整Ɽ挠楥楬杮映湡眠瑩⁨牂獵⁨敌獳䐠物捥⁴畃牲湥⁴䈨䑌⥃䴠瑯牯‬汣獡⁳景椠獮汵瑡潩㩮䈠‬″潮⹳戠慬敤ⱳ搠睯潲⁤灵潴㌠‰浣氠湯⁧‬′潮⹳挠湡灯敩ⱳ猠慨正敬欠瑩‬慳敦祴爠灯ⱥ挠灯数⁲楷摮湩Ⱨ倠睯牥䘠捡潴⁲潮⁴敬獳琠慨⸰ⰹ匠灵汰ⱹ䤠獮慴汬瑡潩Ɱ吠獥楴杮愠摮䌠浯業獳潩楮杮漠⁦㈱〰洠睳敥Ɒ䈠䕅㔠猠慴⁲慲整Ɽ挠楥楬杮映湡眠瑩⁨牂獵⁨敌獳䐠物捥⁴畃牲湥⁴䈨䑌⥃䴠瑯牯‬汣獡⁳景椠獮汵瑡潩㩮䈠‬″潮⹳戠慬敤ⱳ搠睯潲⁤灵潴㌠‰浣氠湯⁧‬′潮⹳挠湡灯敩ⱳ猠慨正敬欠瑩‬慳敦祴爠灯ⱥ挠灯数⁲楷摮湩Ⱨ倠睯牥䘠捡潴⁲潮⁴敬獳琠慨⸰ⰹ匠牥楶散嘠污敵⠠䵃䴯圯 業楮畭ⰸ䄠物搠汥癩牥⁹業楮畭ㄲ‵畃⽭楍Ɱ㌠〵删䵐⠠潴敬慲据⁥獡瀠牥䤠⁓›㜳ⴴ〲㤱Ⱙ吠䑈氠獥⁳桴湡ㄠ┰‬眠瑩潨瑵爠浥瑯⁥湡⁤潣灭瑡扩敬眠瑩⁨硥獩楴杮猠整⁰汥捥牴湯捩爠来汵瑡牯甠楮⁴潦⁲灳敥⁤潣瑮潲湡⁤污敲慭湩湩⁧捡散獳牯敩⁳湩汣摵湩⁧慳敦祴瀠湩‬畮⁴潢瑬ⱳ眠獡敨獲‬整灭牥瑡牵⁥楲敳㜠‵敤牧敥䌠⠠慭⹸Ⱙ椠獮汵瑡潩敲楳瑳湡散洠牯⁥桴湡㈠洠来⁡桯Ɑ猠極慴汢⁥潦⁲㌲‰ⱖ㔠‰穈‬楳杮敬瀠慨敳䄠⁃畓灰祬‬慥瑲楨杮攠捴‮潣灭敬整愠⁳敲畱物摥‮⠊䱂䍄䌠楥楬杮映湡眠瑩⁨業楮畭′敹牡圠牡慲瑮⁹景†瑁浯敢杲 獕慨 牏敩瑮⼠䠠癡汥獬⼠牃浯瑰湯†慭敫 ²匀灵汰楹杮愠摮映硩湩⁧睴潭畤敬猠整灰摥琠灹⁥汥捥牴湯捩映湡爠来汵瑡牯漠桴⁥硥獩楴杮洠摯汵牡瀠慬整猠楷捴⁨潢⁸湩汣摵湩⁧潣湮捥楴湯⁳畢⁴硥汣摵湩⁧潭畤慬⁲汰瑡⁥瑥⹣愠⁳敲畱物摥弮ंSupply, installation, testing and commissioning of COB Recessed LED downligh with DALI enabled driver delivering system lumen >2600 lumens & the luminaire shall be with system efficacy ≥ 110 Im / W. in PD aluminium powder coated white, wide beam angle and operating CCT ≥5000K , input voltage range of 140 to 270V ,THD ≤ 10% & PF ≥ 0.95, Life-50,000 Hrs LED Life with L70 Criteria. Luminaire shall have minimum surge protection of 6KV. The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacturer. [Make- LT Model No. INTENSO G5 MAX or equivalent in Havells/Regent/Phillips]3eȅ̉匀甀瀀瀀氀礀Ⰰ 椀渀猀琀愀氀氀愀琀椀漀渀Ⰰ 琀攀猀琀椀渀最 ☀ 挀漀洀洀椀猀猀椀漀渀椀渀最 漀昀 䰀䔀䐀 ⠀圀愀爀洀 䰀椀最栀琀⤀ 匀椀渀最氀攀 倀栀愀猀攀 吀爀愀挀欀 䴀漀甀渀琀攀搀 䐀䄀䰀䤀 攀渀愀戀氀攀搀 䰀椀最栀琀 昀椀砀琀甀爀攀 Ⰰ 栀漀甀猀椀渀最 洀愀搀攀 甀瀀 漀昀 䐀椀攀ⴀ挀愀猀琀 䄀氀甀洀椀渀椀甀洀 眀椀琀栀 倀䌀⼀䜀氀愀猀猀 䐀椀昀昀甀猀攀爀 搀攀氀椀瘀攀爀椀渀最 愀 洀椀渀椀洀甀洀 猀礀猀琀攀洀 氀甀洀攀渀猀 漀昀 ㄀ 氀甀洀攀渀猀 愀渀搀 洀椀渀椀洀甀洀 猀礀猀琀攀洀 氀甀洀椀渀漀甀猀 攀昀昀椀挀愀挀礀 漀昀 ㄀ 氀洀⼀圀Ⰰ 愀瘀攀爀愀最攀 氀椀昀攀 䰀㜀 䈀㔀 㨀 㔀 栀漀甀爀猀Ⰰ 吀䠀䐀 搀•㄀ ─Ⰰ 猀甀椀琀愀戀氀攀 昀漀爀 漀瀀攀爀愀琀椀漀渀 漀渀 ㄀㐀 ⴀ㈀㜀 嘀Ⰰ ㄀ꘀⰃ 㔀 䠀稀 䄀䌀 猀甀瀀瀀氀礀 猀礀猀琀攀洀Ⰰ 猀甀椀琀愀戀氀攀 昀漀爀 洀漀甀渀琀椀渀最 漀渀 猀椀渀最氀攀 瀀栀愀猀攀 ㌀ 眀椀爀攀 甀渀椀瘀攀爀猀愀氀 琀爀愀挀欀 猀礀猀琀攀洀 椀渀挀氀甀搀椀渀最 挀漀渀渀

ections and earthing etc. as required. 1zȄǵ匁甀瀀瀀氀礀Ⰰ 椀渀猀琀愀氀氀愀琀椀漀渀Ⰰ 琀攀猀琀椀渀最 ☀ 挀漀洀洀椀猀猀椀漀渀椀渀最 漀昀 䰀䔀䐀 ⠀圀愀爀洀 䰀椀最栀琀⤀ 匀椀渀最氀攀 倀栀愀猀攀 吀爀愀挀欀 䴀漀甀渀琀攀搀 䰀椀最栀琀 昀椀砀琀甀爀攀 Ⰰ 栀漀甀猀椀渀最 洀愀搀攀 甀瀀 漀昀 䐀椀攀ⴀ挀愀猀琀 䄀氀甀洀椀渀椀甀洀 眀椀琀栀 倀䌀⼀䜀氀愀猀猀 䐀椀昀昀甀猀攀爀 搀攀氀椀瘀攀爀椀渀最 愀 洀椀渀椀洀甀洀 猀礀猀琀攀洀 氀甀洀攀渀猀 漀昀 ㄀ 氀甀洀攀渀猀 愀渀搀 洀椀渀椀洀甀洀 猀礀猀琀攀洀 氀甀洀椀渀漀甀猀 攀昀昀椀挀愀挀礀 漀昀 ㄀ 氀洀⼀圀Ⰰ 愀瘀攀爀愀最攀 氀椀昀攀 䰀㜀 䈀㔀 㨀 㔀 栀漀甀爀猀Ⰰ 吀䠀䐀 搀•㄀ ─Ⰰ 猀甀椀琀愀戀氀攀 昀漀爀 漀瀀攀爀愀琀椀漀渀 漀渀 ㄀㐀 ⴀ㈀㜀 嘀Ⰰ ㄀ꘀⰃ 㔀 䠀稀 䄀䌀 猀甀瀀瀀氀礀 猀礀猀琀攀洀Ⰰ 猀甀椀琀愀戀氀攀 昀漀爀 洀漀甀渀琀椀渀最 漀渀 猀椀渀最氀攀 瀀栀愀猀攀 ㌀ 眀椀爀攀 甀渀椀瘀攀爀猀愀氀 琀爀愀挀欀 猀礀猀琀攀洀 椀渀挀氀甀搀椀渀最 挀漀渀渀攀挀琀椀漀渀猀 愀渀搀 攀愀爀琀栀椀渀最 攀琀挀⸀ 愀猀 爀攀焀甀椀爀攀搀⸀ᘀंSupply, installation, testing, and commissioning of integrated LED Batten luminaire, 1200 mm (nominal size) with a minimum system lumen output of 2400 lumen and with a minimum system luminous efficacy of 120 lm/W, made of aluminium housing having a colour temperature 5500K - 6500 K, Average life L70B50: 50000 hours, THD ≤ 10%, suitable for operation on 140-270V, 1Φ, 50Hz AC supply system, complete with all accessories, electronic driver, diffuser, directly on the ceiling/wall, including connections, earthing, etc. as required. ’œÌÔȃĉ匀甀瀀瀀氀礀Ⰰ 椀渀猀琀愀氀氀愀琀椀漀渀Ⰰ 琀攀猀琀椀渀最Ⰰ 愀渀搀 挀漀洀洀椀猀猀椀漀渀椀渀最 漀昀 䰀䔀䐀 戀甀氀欀栀攀愀搀 昀椀琀琀椀渀最猀 眀椀琀栀 䤀倀 㘀㘀 椀渀最爀攀猀猀 瀀爀漀琀攀挀琀椀漀渀Ⰰ 眀椀琀栀 愀 洀椀渀椀洀甀洀 猀礀猀琀攀洀 氀甀洀攀渀 漀甀琀瀀甀琀 漀昀 ㄀ 氀甀洀攀渀猀 愀渀搀 愀 洀椀渀椀洀甀洀 猀礀猀琀攀洀 氀甀洀椀渀漀甀猀 攀昀昀椀挀愀挀礀 漀昀 ㄀ 氀洀⼀圀Ⰰ 洀愀搀攀 漀昀 愀氀甀洀椀渀椀甀洀 栀漀甀猀椀渀最 栀愀瘀椀渀最 愀 挀漀氀漀甀爀 琀攀洀瀀攀爀愀琀甀爀攀 漀昀 㔀㔀 䬀ጀ㘠㔀 䬀Ⰰ 愀瘀攀爀愀最攀 氀椀昀攀 䰀㜀 䈀㔀 㨀 㔀 栀漀甀爀猀Ⰰ 猀甀椀琀愀戀氀攀 昀漀爀 漀瀀攀爀愀琀椀漀渀 漀渀 ㄀㐀 ⴀ㈀㜀 嘀Ⰰ ㄀ꘀⰃ 㔀 䠀稀 䄀䌀 猀甀瀀瀀氀礀 猀礀猀琀攀洀Ⰰ 挀漀洀瀀氀攀琀攀 眀椀琀栀 愀氀氀 愀挀挀攀猀猀漀爀椀攀猀Ⰰ 搀椀昀昀甀猀攀爀Ⰰ 攀氀攀挀琀爀漀渀椀挀 搀爀椀瘀攀爀Ⰰ 攀琀挀⸀ 愀猀 爀攀焀甀椀爀攀搀 搀椀爀攀挀琀氀礀 漀渀 琀栀攀 眀愀氀氀Ⰰ 椀渀挀氀甀搀椀渀最 挀漀渀渀攀挀琀椀漀渀猀Ⰰ 攀琀挀⸀ 愀猀 爀攀焀甀椀爀攀搀⸀ Ȁᬂ଀ĂSupply, installation, testing, and commissioning of integrated LED Batten luminaire, 600 mm (nominal size) with a minimum system lumen output of 1000 lumen and with a minimum system luminous efficacy of 100 lm/W, made of aluminium housing having a colour temperature 5500K - 6500 K, Average life L70B50: 50000 hours, suitable for operation on 140-270V, 1Φ, 50Hz AC supply system, complete with all accessories, electronic driver, diffuser, directly on the ceiling/wall, including connections, earthing, etc. as required. ǎĉ匀甀瀀瀀氀礀Ⰰ 椀渀猀琀愀氀氀愀琀椀漀渀Ⰰ 琀攀猀琀椀渀最 愀渀搀 挀漀洀洀椀猀猀椀漀渀椀渀最 漀昀 猀甀爀昀愀挀攀 洀漀甀渀琀攀搀 䰀䔀䐀 搀漀眀渀氀椀最栀琀攀爀 氀甀洀椀渀愀椀爀攀 椀渀 洀攀琀愀氀氀椀挀 栀漀甀猀椀渀最Ⰰ 眀椀琀栀 愀 洀椀渀椀洀甀洀 猀礀猀琀攀洀 氀甀洀攀渀 漀甀琀瀀甀琀 漀昀 ㄀㠀 氀甀洀攀渀 愀渀搀 眀椀琀栀 愀 洀椀渀椀洀甀洀 猀礀猀琀攀洀 氀甀洀椀渀漀甀猀 攀昀昀椀挀愀挀礀 漀昀 ㄀ 氀洀⼀圀Ⰰ 䄀瘀攀爀愀最攀 䰀䔀䐀 氀椀昀攀 䰀㜀 䈀㔀 㨀 㔀 栀漀甀爀猀Ⰰ 猀甀椀琀愀戀氀攀 昀漀爀 漀瀀攀爀愀琀椀漀渀 漀渀 ㄀㐀 ⴀ㈀㜀 嘀Ⰰ ㄀ꘀⰃ 㔀 䠀稀 䄀䌀 猀甀瀀瀀氀礀 猀礀猀琀攀洀Ⰰ 挀漀洀瀀氀攀琀攀 眀椀琀栀 愀氀氀 愀挀挀攀猀猀漀爀椀攀猀Ⰰ 搀椀昀昀甀猀攀爀 愀渀搀 攀氀攀挀琀爀漀渀椀挀 搀爀椀瘀攀爀Ⰰ 搀椀爀攀挀琀氀礀 漀渀 挀攀椀氀椀渀最Ⰰ 椀渀挀氀甀搀椀渀最 挀漀渀渀攀挀琀椀漀渀猀 愀渀搀 攀愀爀琀栀椀渀最 攀琀挀⸀ 愀猀 爀攀焀甀椀爀攀搀⸀ ਀촀༁䌀
畓灰祬湩⁧湡⁤湩瑳污楬杮映汯潬楷杮猠穩⁥景瀠牥潦慲整⁤潈⁴楄灰摥䜠污慶楮敳⁤牉湯挠扡敬琠慲⁹䜨污慶楮慳楴湯琠楨正敮獳渠瑯氠獥⁳桴湡㔠‰業牣湯⥳眠瑩⁨数晲牯瑡潩潮⁴潭敲琠慨㜱㔮Ⱕ椠潣癮湥敩瑮猠捥楴湯ⱳ樠楯敮⁤楷桴挠湯敮瑣牯ⱳ猠獵数摮摥映潲桴⁥散汩湩⁧楷桴䜠䤮‮畳灳湥敤獲椠据畬楤杮䜠䤮‮潢瑬⁳…畮獴‬瑥⹣愠⁳敲畱物摥⴮〱‰浭眠摩桴堠㔠‰浭搠灥桴堠ㄠ㘮洠桴捩湫獥⵳㔱‰浭眠摩桴堠㔠‰浭搠灥桴堠ㄠ㘮洠桴捩湫獥⵳〳‰浭眠摩桴堠㔠‰浭搠灥桴堠ㄠ㘮洠桴捩湫獥䅳āSupplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “bends” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.Ŀ匀灵汰楹杮愠摮椠獮慴汬湩⁧潦汬睯湩⁧楳敺漠⁦数晲牯瑡摥䠠瑯䐠灩数⁤慇癬湡獩摥䤠潲慣汢⁥牴祡∠敔≥⠠慧癬湡獩瑡潩潮⁴敬獳琠慨〵洠捩潲獮 楷桴瀠牥潦慲楴湯渠瑯洠牯⁥桴湡ㄠ⸷┵‬湩挠湯敶楮湥⁴敳瑣潩獮‬潪湩摥眠瑩⁨潣湮捥潴獲‬畳灳湥敤⁤牦浯琠敨挠楥楬杮眠瑩⁨⹇⹉猠獵数摮牥⁳湩汣摵湩⁧⹇⹉戠汯獴☠渠瑵ⱳ攠捴‮獡爠煥極敲⹤ň匁甀瀀瀀氀礀椀渀最 愀渀搀 椀渀猀琀愀氀氀椀渀最 昀漀氀氀漀眀椀渀最 猀椀稀攀 漀昀 瀀攀爀昀漀爀愀琀攀搀 䠀漀琀 䐀椀瀀瀀攀搀 䜀愀氀瘀愀渀椀猀攀搀 䤀爀漀渀 挀愀戀氀攀 琀爀愀礀 ᰀ䌠爀漀猀猀 洀攀洀戀攀爀ᴀ†⠀最愀氀瘀愀渀椀猀愀琀椀漀渀 渀漀琀 氀攀猀猀 琀栀愀渀 㔀 洀椀挀爀漀渀猀⤀ 眀椀琀栀 瀀攀爀昀漀爀愀琀椀漀渀 渀漀琀 洀漀爀攀 琀栀愀渀 ㄀㜀⸀㔀─Ⰰ 椀渀 挀漀渀瘀攀渀椀攀渀琀 猀攀挀琀椀漀渀猀Ⰰ 樀漀椀渀攀搀 眀椀琀栀 挀漀渀渀攀挀琀漀爀猀Ⰰ 猀甀猀瀀攀渀搀攀搀 昀爀漀洀 琀栀攀 挀攀椀氀椀渀最 眀椀琀栀 䜀⸀䤀⸀ 猀甀猀瀀攀渀搀攀爀猀 椀渀挀氀甀搀椀渀最 䜀⸀䤀⸀ 戀漀氀琀猀 ☀ 渀甀琀猀Ⰰ 攀琀挀⸀ 愀猀 爀攀焀甀椀爀攀搀⸀倀
畓灰祬‬湩瑳污慬楴湯‬整瑳湩⁧湡⁤潣浭獩楳湯湩⁧景䐠义刭楡潍湵⁴祴数‬㐲〰䅭倠睯牥匠灵汰⁹潍畤敬映牯传敶⁲潖瑬条⁥湡⁤桓牯⁴楃捲極⁴牰瑯捥楴湯栠癡湩⁧䍄䌯䵏䐯呁⁁潃湮捥楴湯瀠牯獴猠極慴汢⁥潴漠数慲整漠ㄱ嘰㈯〲ⱖ㔠ⴰ〶穈䄠⁃畳灰祬搠汥癩牥湩⁧畏灴瑵挠牵敲瑮漠⁦㐲〰䅭愠⁴㐲⁖䍄攠捴愠⁳敲畱物摥‮††††††††††††††††††††͓Ј匀灵汰ⱹ椠獮慴汬瑡潩Ɱ琠獥楴杮愠摮挠浯業獳潩楮杮漠⁦浳牡⁴畍瑬⵩畦据楴湯琠畯档瀠湡汥椠䉁ⱓ䍐栠獯極杮愠潬睧瑩⁨畳瑩扡敬倠湡汥瀠睯牥椠瑮牥慦散映牯漠数慲楴湯漠㈱㌭嘰䐠⁃畳灰祬眠瑩⁨潦汬睯湩⁧敦瑡牵獥㨠††††††††††††††††††††††††††††††††††††††††††††††††††††††敋⁹潍敤›楓杮敬漠⽮景ⱦ匠湩汧⁥湯‬楓杮敬漠晦‬潃扭⵩慮楴湯漠Ɱ䌠浯楢慮楴湯漠晦‬潃扭湩瑡潩湯漯晦‬潄扵敬挠楬正猠湩汧⁥湯漯晦‬潄扵敬挠楬正挠浯楢慮楴湯漠⽮景⹦䬊祥䌠湯牴汯吠灹㩥匠散敮‬敓畱湥散‬楔敭Ⱳ唠楮敶獲污匠楷捴ⱨ匠湩汧⁥桃湡敮潃瑮潲ⱬ䈠潲摡慣瑳匠散敮‬

aspect ratio. Power input shall be AC 100–240V, 50/60 Hz. The system shall be configured to achieve a minimum resolution of 1920×1080 (Full HD). The complete system shall carry a comprehensive onsite warranty of five (5) years from the date of installation and commissioning, covering all LED modules, power supplies, receiving cards, controllers, and accessories. it should come with 5 years warranty with CE or FCC or UL certifications. »ÑǪ匀呉⁃景㔠∵倠潲敦獳潩慮汕牴⁡䑈䐠獩汰祡倠湡汥‬䬴唠䑈⠠㠳〴㉸㘱⤰删獥汯瑵潩Ɱ䈠楲桧湴獥⁳㔳‰楎獴‬潃瑮慲瑳删瑡潩⠠祔⹰㨩㐠〰㨰ⰱ嘠敩楷杮愠杮敬⠠潨楲潺瑮污☠瘠牥楴慣⥬›㜱‸ 㜱‸敤牧敥‬灏牥瑡潩慮潈牵›㘱㝸匬整敲楍楮䨠捡Ⱬ䌠湯敮瑣癩瑩㩹嘠摩潥䤠灮瑵䴺湩㈠䠠䵄⁉⸲ⰰ㈠唠䉓㈠〮‬潃瑮潲㩬删㉓㈳‬瑅敨湲瑥‬砲〱⁗畂汩⵴湩猠数歡牥ⱳ䌠㕁″⸱䜳穈儠慵ⵤ潃敲‬‸䉇䤠扮極瑬洠浥牯ⱹ䌠ⱅ䘠䍃‬䱕‬䥂ⱓ䤠体㐠〵㄰䌠牥楴楦摥攠捴愠汬挠浯汰瑥⹥传楲湥慴楴湯ⴠ䰠湡獤慣数☠倠牯牴楡⁴楷桴㔠礠慥獲眠牡慲瑮ꙹ畓灰祬愠摮䤠獮慴汬瑡潩景䌠单佔⁍呓乁⁄啗䡔吠佒䱌剅圠呉⁈ⴳ‴䑁啊呓䉁䕌䄠䝎䕌⁓湩汣摵湩⁧桷敥獬映牯爠瑯瑡湩⁧獡瀠牥搠獥杩湡⁤敤慴汩⁳灡牰癯摥戠⁹湅楧敮牥䤠据慨杲⹥ǚ匀灵汰ⱹ䤠獮慴汬瑡潩Ɱ吠獥楴杮☠挠浯業獳潩楮杮漠⁦ㄲ㔮椭据⁨畆汬䠠⁄ㄨ㈹휰〱〸 偉⁓慰敮獬漠晦牥湩⁧楷敤ㄠ㠷搭来敲⁥楶睥湩⁧湡汧獥眠瑩⁨㘱㜮洠汩楬湯挠汯牯猠灵潰瑲‮瑩猠潨汵⁤畳灰牯⁴潢桴䠠䵄⁉湡⁤䝖⁁潣湮捥楴楶祴映牯瘠牥慳楴敬搠癥捩⁥潣灭瑡扩汩瑩ⱹ漠晦牥⁳楴瑬愠橤獵浴湥⁴潦⁲潣晭牯慴汢⁥楶睥湩Ⱨ愠摮映慥畴敲⁳汵牴ⵡ汳浩戯牯敤汲獥⁳敤楳湧⁳潦⁲潭敤湲愠獥桴瑥捩⹳䄠汬愠敲䔠敮杲⁹瑓牡挠牥楴楦摥眠瑩⁨敭捲牵⵹牦敥戠捡汫杩瑨湩⁧整档潮潬祧愠摮椠据畬敤挠扡敬洠湡条浥湥⁴潳畬楴湯⹳錠畓灰祬‬湉瑳污慬楴湯‬敔瑳湩⁧…潣浭獩楳湯湩⁧景倠婔挠浡牥⁡桳污敢㐠⁋䡕⁄祴数眠瑩⁨業楮畭⼱⸲ⴵ湩档䌠位⁓敳獮牯搠汥癩牥湩⁧㠳〴㋗㘱‰敲潳畬楴湯愠⁴業楮畭〳灦⁳楷桴洠湩浩浵㌠砰稠潯慣慰楢楬祴椠䬴椠据畬楤杮挠敬牡椠慭敧稠潯湡⁤畡潴潦畣⹳䌠浡牥⁡桳污畳灰牯⁴䥁瀭睯牥摥愠瑵ⵯ牴捡楫杮映牯愠瑵湯浯畯⁳牰獥湥整⁲潦汬睯湩⁧楶⁡畢汩⵴湩瀠潲散獳湩⁧牯氠捩湥慳汢⁥潳瑦慷敲‮楓畭瑬湡潥獵瘠摩潥漠瑵異獴猠慨汬椠据畬敤䠠䵄ⱉ㌠ⵇ䑓ⱉ愠摮䤠⁐瑳敲浡湩⁧楷桴丠䥄䡼⁘牰瑯捯汯猠灵潰瑲‮慃敭慲猠慨汬瀠潲楶敤瀠湡爠湡敧넠㜱뀰‬楴瑬爠湡敧ⴠ〳₰潴⬠〹Ⲱ洠湩浩浵ㄠ〰瀠敲敳⁴潰楳楴湯ⱳ倠䕯‫潰敷Ⱳ愠摮䤠ⵐ慢敳⁤敷⁢潣普杩牵瑡潩⹮䌠ⱅ䘠䍃‬潒午挠牥楴楦摥⠠慗牲湡祴ⴠ㔠夠慥獲温䥓䍔漠⁦噁漭敶⵲偉攠据摯牥猠慨汬猠灵潰瑲㐠㙋‰㨴㨴‴楶敤湥潣楤杮漠敶⁲瑳湡慤摲ㄠ扇獰䔠桴牥敮⁴楷桴氠睯氭瑡湥祣挠摯捥‮湅潣敤⁲桳污牰癯摩⁥湯⁥单ⵂ⁃湩異⁴楷桴洠湩浩浵㘠地瀠睯牥搠汥癩牥⁹湡⁤湯⁥䑈䥍㈠〮椠灮瑵猠灵潰瑲湩⁧䑈偃㈠㈮‬楷桴愠瑵浯瑡捩漠⁲慭畮污椠灮瑵猠楷捴楨杮愠摮漠敮䠠䵄⁉潬灯畯⹴唠楮⁴桳污畳灰牯⁴䑈⁒潣瑮湥ⱴ瘠摩潥猠慣楬杮‬慦瑳猠楷捴楨杮‬湡⁤業楮畭ⴸ档湡敮䍐⁍浥敢摤摥愠摵潩眠瑩⁨敮睴牯敫⁤畡楤畳灰牯楴杮䄠卅㜶漠⁲煥極慶敬瑮‮湅潣敤⁲桳污湩汣摵⁥偉戭獡摥挠湯牴汯‬卒㈭㈳猠牥慩潰瑲‬潐⁅畳灰牯ⱴ愠摮洠汵楴潰湩⵴潴洭汵楴潰湩⁴楶敤慭牴硩挠灡扡汩瑩⹹䕃‬䍆ⱃ删䡯⁓散瑲晩敩⁤㔨夠䅅卒圠剁䅒呎⥙Ϭ匀呉⁃景㐠䁋〶嘠摩潥漠敶⁲䜱䔠据摯牥‬楷桴䠠䵄⁉⸲‰䬴㙀䠰⁺㨴㨴‴楷桴䠠䍄⁐⸲′潣灭瑡扩汩瑩ⱹㄠ⁸䑈䥍眠瑩⁨单㉂〮栠獯⁴潰瑲‬砱䠠䵄⁉潬灯畯⁴畯灴瑵‬㈱戭瑩挠汯牯搠灥桴瀠潲散獳湩⁧潦⁲敢瑴牥搠敥⁰潣潬⁲浩条ⱥ䠠剄〱‬䑈ㅒ⬰‬潄扬⁹楖楳湯‬楖敤捓污湩⁧牦浯愠祮爠獥汯瑵潩潴愠祮爠獥汯瑵潩Ɱ䰠睯氠瑡湥祣縠‱牦浡⁥湩唠瑬慲䰠睯䰠瑡湥祣䴠摯ⱥ猠灵潰瑲映獡⁴睳瑩档湩Ⱨ戠極瑬椭楖敤慗汬⼠䴠獯楡⁣楖敤慗汬猠灵潰瑲眠瑩⁨潲慴楴湯愠摮戠穥汥挠浯数獮瑡潩Ɱ嘠摩潥㤠⼰㠱⼰㜲‰潲慴楴湯‬潨楲潺瑮污愠摮瘠牥楴慣汦灩‬畍瑬灩楯瑮琠畭瑬灩楯瑮瘠摩潥琠慲獮業獳潩潦⁲楶敤癯牥攠桴牥敮⁴慭牴硩‬灯楴湯污䐠湡整䄠ⵖ⁁湉整牧瑡潩嘨摩潥匠楷捴楨杮眠瑩⁨慄瑮⁥潃瑮潲汬牥Ⱙ愠慮潬⁧浥敢摤湩⁧潴䠠䵄ⱉ愠慮潬⁧敤攭扭摥楤杮映潲䑈䥍‬剁⁃ 䅥䍒猠灵潰瑲‬灕琠‸档湡敮獬䰠䍐⁍䑈䥍漠⁲潣灭敲獳摥愠摵潩甠⁰潴䐠汯祢䄠浴獯愠摮䐠協堭‬砸‸偌䵃䐠湡整䄠摵潩䔠扭摥敤⁤楷桴䐠湡整删慥祤挠灡扡汩瑩ⱹ挠湯牴汯⁳癯牥䤠⁐湩汣摵湩⁧敓楲污眠瑩⁨敓楲污䜠湥牥瑡潩慃慰楢楬祴‬湡⁤剉漠敶⁲偉眠瑩⁨剉䜠湥牥瑡潩慃慰楢楬祴‮䕃‬䍆ⱃ删䡯⁓散瑲晩敩蝤䥓䍔漠⁦噁漭敶⵲偉攠据摯牥猠慨汬猠灵潰瑲㐠㙋‰㨴㨴‴楶敤湥潣楤杮漠敶⁲瑳湡慤摲ㄠ扇獰䔠桴牥敮⁴獵湩⁧潬⵷慬整据⁹楶畳污祬氠獯汳獥⁳潣敤⁣楷桴䠠䵄⁉⸲‰湩異⁴畳灰牯楴杮䠠䍄⁐⸲′潣灭楬湡散愠摮漠敮䠠䵄⁉潬灯畯⁴畯灴瑵‮湅潣敤⁲桳污畳灰牯⁴浥敢摤摥洠汵楴挭慨湮汥䠠䵄⁉畡楤楷桴渠瑥潷歲摥愠摵潩挠灡扡汩瑩⁹畳灰牯楴杮䄠卅㜶漠⁲煥極慶敬瑮瀠潲潴潣⹬唠楮⁴桳污牰癯摩⁥单⁂⸲‰楳湧污爠畯楴杮‬卒㈭㈳猠牥慩潣瑮潲癯牥䤠ⱐ愠摮倠䕯瀠睯牥挠灡扡汩瑩⁹楷桴䤠ⵐ慢敳⁤慭慮敧敭瑮瘠慩眠扥椠瑮牥慦散‮湅潣敤⁲桳污畳灰牯⁴畭瑬灩楯瑮琭ⵯ畭瑬灩楯瑮䤠⁐楶敤慭牴硩猠楷捴楨杮愠摮匠呒⽐䕁⁓湥牣灹整⁤瑳敲浡琠慲獮潰瑲‮䕃‬䍆ⱃ删䡯⁓散瑲晩敩⹤⠠‵䕙剁⁓䅗剒乁奔༩䥓䍔漠⁦牰景獥楳湯污札慲敤唠䉓戠楲杤⁥敤楶散‬敤楳湧摥琠湩整晲捡⁥瑳湡慤摲唠䉓攭慮汢摥挠浯異楴杮搠癥捩獥映牯挠湯敦敲据湩⁧慣敭慲愠摮愠摵潩愠灰楬慣楴湯⹳吠敨搠癥捩⁥桳污畳灰牯⁴楢楤敲瑣潩慮单⁂牴湡浳獩楳湯眠瑩⁨汰杵愭摮瀭慬⁹畦据楴湯污瑩⁹湡⁤桳污敢挠浯汰慩瑮眠瑩⁨单⁂⸲‰牯栠杩敨⁲瑳湡慤摲⹳吠敨甠楮⁴桳污湩整牧瑡⁥敳浡敬獳祬眠瑩⁨湥潣敤⁲湡⁤敤潣敤⹲吠敨搠癥捩⁥桳污湩汣摵⁥灡牰灯楲瑡⁥单⁂祔数䈭愠摮唠䉓吠灹ⵥ⁁潰瑲愠潬杮眠瑩⁨敮睴牯潣湮捥楴楶祴⠠楇慧楢⁴瑅敨湲瑥⸩吠敨搠癥捩⁥桳污敢瀠睯牥摥瘠慩倠䕯⠠潐敷⁲癯牥䔠桴牥敮⥴愠摮猠慨汬椠据畬敤猠慴畴⁳湩楤慣潴獲映牯瀠睯牥‬敮睴牯潣湮捥楴楶祴‮桔⁥湵瑩猠慨汬戠⁥畳瑩扡敬映牯爠捡⵫潭湵⁴牯甠摮牥琭扡敬椠獮慴汬瑡潩湡⁤桳污潣灭祬眠瑩⁨湩整湲瑡潩慮瑳湡慤摲⁳畳档愠⁳䕃‬䍆ⱃ愠摮删䡯⁓湡⁤潣敭⁳楷桴㔠夠慥獲眠牡慲瑮赹䥓䍔漠⁦噁漭敶⵲偉猠獹整潣瑮潲汬牥猠慨汬瀠潲楶敤挠湥牴污穩摥洠湡条浥湥⁴湡⁤潣普杩牵瑡潩景愠汬渠瑥潷歲摥瘠摩潥攠据摯牥⁳湡⁤敤潣敤獲眠瑩⁨畡潴慭楴⁣湥灤楯瑮搠獩潣敶祲‮潃瑮潲汬牥猠慨汬漠晦牥䤠ⵐ慢敳⁤慭慮敧敭瑮瘠慩眠扥䜠䥕‬敔湬瑥䄠䥐‬湡⁤卒㈭㈳猠牥慩湩整晲捡⁥畳灰牯楴杮琠楨摲瀭牡祴挠湯牴汯猠獹整湩整牧瑡潩⹮匠獹整桳污湥扡敬洠瑡楲⵸瑳汹⁥楶敤睳瑩档湩⁧湡⁤潲瑵湩⁧敢睴敥畭瑬灩敬攠据摯牥⁳湡⁤敤潣敤獲漠敶⁲瑳湡慤摲ㄠ扇獰洠湡条摥䔠桴牥敮⁴敮睴牯楷桴爠慥⵬楴敭攠摮潰湩⁴瑳瑡獵洠湯瑩牯湩⹧唠楮⁴桳污敦瑡牵⁥潐⁅潰敷⁲慣慰楢楬祴‬畤污䜠杩扡瑩䔠桴牥敮⁴潰瑲ⱳ愠摮瀠睯牥猯慴畴⁳䕌⁄湩楤慣潴獲‮䕃‬䍆ⱃ删䡯⁓散瑲晩敩⹤⠠‵䕙剁⁓䅗剒乁奔⬩ăSITC of switch with 1U rack-mount, fully managed Layer 2/Layer 3 Multi-Gigabit Ethernet switch with minimum 24× RJ45 ports supporting 1G to 10G speeds with IEEE 802.3bt PoE++ delivering minimum 60W per port and a total PoE budget of not less than 1,440W via dual hot-swappable redundant power supplies. It shall provide minimum 2× 10G SFP+ uplink ports, non-blocking switching capacity of minimum 640 Gbps, IGMP v1/v2/v3 Snooping with Querier, IEEE 1588 PTPv2, IEEE 802.1Q VLANs, MACsec encryption, 802.1X authentication, LACP link aggregation, STP/RSTP/MSTP, and stacking bandwidth of minimum 480 Gbps with hitless failover. Management shall include Web GUI, CLI, SNMP v3, REST API, and cloud management platform. Unit shall operate on 100–240V AC and comply with FCC Part 15A, CE, and UL/IEC safety standards.ɶ匀呉⁃景㐠⁋䑈䥍琠单⁂楶敤慣瑰牵⁥敤楶散猠慨汬愠捣灥⁴䑈䥍㈠〮椠灮瑵猠灵潰瑲湩⁧敲潳畬楴湯⁳灵琠䬴㙀䠰⁺㨴㨴‴楷桴䠠䍄⁐⸲′潣灭楬湡散‬䑈⁒畳灰牯ⱴ愠摮ㄠ䜸灢⁳楶敤慢摮楷瑤⹨i

Device shall provide USB 3.0 capture output with built-in 4K@60Hz downscaling to 1080p@60Hz supporting uncompressed YUV2 via USB 3.0. Unit shall support embedded HDMI audio capture and be compatible with Windows and macOS operating systems. Device shall work with standard UVC video conferencing applications including Zoom, Teams, OBS, and VLC. USB bus-powered, compact plug-and-play design. CE, FCC, RoHS certified. with 5 Years warranty support.ÆSITC 4K60 multi-window processor shall provide minimum four HDMI 2.0 inputs with HDCP 2.2 compliance, 18Gbps video bandwidth, and 4K@60Hz HDMI output on single UHD display. Processor shall support multiple windowing modes including single full-screen, picture-in-picture, side-by-side, and quad-view with seamless switching and fully customizable window arrangements. Unit shall support multi-channel audio passthrough with analog stereo audio de-embedding for external distribution systems. Controls shall include front panel buttons, RS-232, Ethernet/IP-based management, and configuration software with EDID management. Compact metal enclosure, 5-year warranty. CE, FCC, RoHS certified (Warranty - 5 Years)
Supply, installation, testing and commissioning of Wireless Presentation & Video Conferencing System with dedicated USB-C Wireless Sharing Pod/Button or equivalent native wireless sharing capability. Base unit shall support 4K video output via HDMI with one HDMI input for wired content. System shall support wireless screen sharing from iOS, Android, Windows, macOS and ChromeOS using native AirPlay, Google Cast and Miracast protocols without proprietary software installation. Minimum two simultaneous screen sharing on single display with built-in moderation/presenter control mode shall be supported. System shall support BYOM wireless video conferencing compatible with MS Teams, Zoom, Google Meet and Webex, enabling wireless bridging of room USB peripherals including camera, microphone and speakers to presenter s laptop. Built-in on-screen annotation and digital whiteboard or equivalent collaboration tools shall be provided. System shall have built-in dual-band Wi-Fi (IEEE 802.11ac or higher) with standalone access point mode, Ethernet RJ-45 LAN with DHCP, enterprise-grade encryption (WPA2 or higher), and centralized cloud-based device management with OTA firmware update capability. USB-C Sharing Pod, where provided, shall enable single-cable plug-and-play BYOD and BYOM operation without driver installation, supporting Windows and macOS. FCC/CE/BIS or equivalent certified. 5-year OEM onsite warranty.ESITC for complete cables as per detail given below and as per available site and solution required as per approval of engineer in charge. # Audio/Speaker/Microphone Cable: SITC of 4 Sqmm Audio cable with PVC or LSZH Insulation, Min. 300V operating voltage, Low resistance copper core. # In Cat 6a its, UTP Cable, Performance: 10GBASE-T, 1000BASE-T, 100BASE-TX, 10BASE-T, 155Mbps ATM, Operating Frequency: Up to 500 MHZ, Conductor: 23 AWG Solid Bare Copper. Shielding: Foil shield around all 4 pairs, Operating Temperature: -40 to 70 degree C'. # Original Nuetrik Connectors. Ï

SITC of 36U standard 19" floor standing server type rack enclosures, constructed from mild steel/CRCA with powder coated finish, 600 800 mm width and 600 1000 mm depth, suitable for Audio, Video & networking. Units shall feature 4 column rack rails, adjustable or fixed depth channels, removable side panels, front glass/ventilated locking doors

cable entry provision,

and integral grounding, with static load capacity not less than 100 500 kg depending on modelVEV/VRF System ISupply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 . tSITC of following electronic components for communication and control of ODUs and AHU as per OEM of VRF/VRV system :.Corded remote control for ductable indoor unitAHU kit Communication kit)Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : |¥T9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation U12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation U15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulationS19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation U22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation U28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation/
Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.Thickness 0.63 mm sheet
Supplying, Fixing, installation, testing and commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core in confirmation to SMACNA/IS and as per specifications complete etc. as required.
Supplying, Fixing, installation, testing and commissioning of Return air diffusers of powder coated aluminium without volume control dampers with anti smudge ring & removable core in confirmation to SMACNA/IS and as per specifications complete etc. as required.
Supplying, Fixing, installation, testing and commissioning of thermal insulated flexible duct of following sizes duly supported at regular interval as per site requirement etc. in confirmation to SMACNA/IS and as per specifications complete etc. as required. 200 mm dia./

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. [For Fabricating frame ODUs of split AC -.Design/Shape will be decided by Engineer-in-charge]ÑxTwo or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufactureEarthingõEarthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.½Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.fProviding and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.¤Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.ÍDemolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. ( Dismantling of feeder pillar / panel foundation)ÊProviding and laying in position cement concrete 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) for the repair of the road after cutting of road for cable repair and laying.Fire Fighting System×Providing and fixing CO 2 High Pressure Portable 4.5 kg Fire Extinguisher, filled with CO 2 Gas as per IS 15222, Gross Weight 16.4, empty weight 11.9 Kg, Control discharge mechanism fitted with 1 Meter Wire Braided Hose & Flat Horn with Diffuser Nozzle for dispersed discharge of CO2, Discharge Time 12 Sec, Average Discharge is 95%, Applicable on Class B, C and electrically started Fire, Fire Rating 55B, Internal coating is not applicable & External coating is of enamel spray painting, Powder Coated Handle, Valve Confirm to IS 3224 ISI Marked, CO2 Cylinder construction: hot spinning by seamless pipes & bearing ISI mark, Body confirms to IS 7285 and PESO APPROVED, Extinguishers confirmed to IS 15683:2018 and ISI marked.Ç
Providing and Fixing ABC Type Fire Extinguisher Cap. 4 kg Filled with Mono Ammonium Phosphate Powder 90% confirms to IS 4308, Stored Pressure Type, UGTS Pressure Gauge, Gross Weight 6.7 Kg, Empty Weight 2.7 Kg, Can Height 490mm, Diameter 140 ± 10mm, Discharge Time 18 Sec, Controllable discharge mechanism, Jet Range 3 Meters, Average Discharge is 92%, applicable on Class A,B & C and electrically started Fire, Fire Rating 4A:144B, Can Construction : Deep drawn & MIG welded, EPDM Rubber Hose with both end Aluminum crimped, Internal & External - Pure Polyester Powder coating (UV Resistant), Brass forged valves with safety Pin is of SS material, Made up from 1.6mm thick sheet, ISI Approved IS 15683:2018. ÆÙSupplying, installation, testing & commissioning of heat detector operating at 54ºC/57ºC with rate of rise cum fixed temperature (dual thermistor) type with mounting base complete with all connection etc. as required.•Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required.­Supplying, installation, testing & commissioning response indicator on surface/recess MS box having two LEDs etallic over complete with all connections etc. as required. ûSupplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in A.B.S. box with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required. T
Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required.4 Zone6Supplying, installation, testing & commissioning of main control and indicating panel made out of 16 SWG MS sheet to accommodate the following items duly powder coated in approved colour with louvers for ventilation, locking arrangement, audio and visual indication for fire alarm and public address system, monitoring system including connections, interconnections etc complete as required. Each 10033.00 10 Zone panel for fire alarm system 250 Watt amplifier racks suitable for operation on 230V AC/24V DC su

Device shall provide USB 3.0 capture output with built-in 4K@60Hz downscaling to 1080p@60Hz supporting uncompressed YUV2 via USB 3.0. Unit shall support embedded HDMI audio capture and be compatible with Windows and macOS operating systems. Device shall work with standard UVC video conferencing applications including Zoom, Teams, OBS, and VLC. USB bus-powered, compact plug-and-play design. CE, FCC, RoHS certified. with 5 Years warranty support.ÆSITC 4K60 multi-window processor shall provide minimum four HDMI 2.0 inputs with HDCP 2.2 compliance, 18Gbps video bandwidth, and 4K@60Hz HDMI output on single UHD display. Processor shall support multiple windowing modes including single full-screen, picture-in-picture, side-by-side, and quad-view with seamless switching and fully customizable window arrangements. Unit shall support multi-channel audio passthrough with analog stereo audio de-embedding for external distribution systems. Controls shall include front panel buttons, RS-232, Ethernet/IP-based management, and configuration software with EDID management. Compact metal enclosure, 5-year warranty. CE, FCC, RoHS certified (Warranty - 5 Years)
Supply, installation, testing and commissioning of Wireless Presentation & Video Conferencing System with dedicated USB-C Wireless Sharing Pod/Button or equivalent native wireless sharing capability. Base unit shall support 4K video output via HDMI with one HDMI input for wired content. System shall support wireless screen sharing from iOS, Android, Windows, macOS and ChromeOS using native AirPlay, Google Cast and Miracast protocols without proprietary software installation. Minimum two simultaneous screen sharing on single display with built-in moderation/presenter control mode shall be supported. System shall support BYOM wireless video conferencing compatible with MS Teams, Zoom, Google Meet and Webex, enabling wireless bridging of room USB peripherals including camera, microphone and speakers to presenter s laptop. Built-in on-screen annotation and digital whiteboard or equivalent collaboration tools shall be provided. System shall have built-in dual-band Wi-Fi (IEEE 802.11ac or higher) with standalone access point mode, Ethernet RJ-45 LAN with DHCP, enterprise-grade encryption (WPA2 or higher), and centralized cloud-based device management with OTA firmware update capability. USB-C Sharing Pod, where provided, shall enable single-cable plug-and-play BYOD and BYOM operation without driver installation, supporting Windows and macOS. FCC/CE/BIS or equivalent certified. 5-year OEM onsite warranty.ESITC for complete cables as per detail given below and as per available site and solution required as per approval of engineer in charge. # Audio/Speaker/Microphone Cable: SITC of 4 Sqmm Audio cable with PVC or LSZH Insulation, Min. 300V operating voltage, Low resistance copper core. # In Cat 6a its, UTP Cable, Performance: 10GBASE-T, 1000BASE-T, 100BASE-TX, 10BASE-T, 155Mbps ATM, Operating Frequency: Up to 500 MHZ, Conductor: 23 AWG Solid Bare Copper. Shielding: Foil shield around all 4 pairs, Operating Temperature: -40 to 70 degree C'. # Original Nuetrik Connectors. Ï

SITC of 36U standard 19" floor standing server type rack enclosures, constructed from mild steel/CRCA with powder coated finish, 600 800 mm width and 600 1000 mm depth, suitable for Audio, Video & networking. Units shall feature 4 column rack rails, adjustable or fixed depth channels, removable side panels, front glass/ventilated locking doors

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

Please Enable Macros to View BoQ information